Skip to contentSkip to conversation

mtd: spi-nor: Move cadence-qaudspi to spi-mem framework

PATCH Superseded Vignesh Raghavendra 2 participants 14 messages Jun 1, 2020

Subsystems (3)
lore
Share & tools
lore

Vignesh Raghavendra

author maintainer
#0 lore raw

v3 cover mtd: spi-nor: Move cadence-qaudspi to spi-mem framework

This series is a subset of "[PATCH v12 0/4] spi: cadence-quadspi: Add support for the Cadence QSPI controller" by Ramuthevar,Vadivel MuruganX <[email protected]> that intended to move cadence-quadspi driver to spi-mem framework

Those patches were trying to accomplish too many things in a single set of patches and need to split into smaller patches. This is reduced version of above series.

Changes that are intended to make migration easy are split into separate patches. Patches 1 to 3 drop features that cannot be supported under spi-mem at the moment (backward compatibility is maintained). Patch 4-5 are trivial cleanups. Patch 6 does the actual conversion to spi-mem and patch 7 moves the driver to drivers/spi folder.

I have tested both INDAC mode (used by non TI platforms like Altera SoCFPGA) and DAC mode (used by TI platforms) on TI EVMs.

Patches to move move bindings over to "Documentation/devicetree/bindings/spi/" directory and also conversion of bindig doc to YAML will be posted separately. Support for Intel platform would follow that.

v3:
Split handling of probe deferral into separate patch (out of 5/6) Split dropping of redundant WREN to separate patch (out of 5/6) Fix a possible memleak due to lack of spi_master_put() Parse all SPI slave nodes in cqspi_setup_flash() Address misc comments from Tudor on v2
Rebase onto latest spi-nor/next

v2:
Rework patch 1/6 to keep "cdns,is-decoded-cs" property supported.

Ramuthevar Vadivel Murugan (2):
mtd: spi-nor: Convert cadence-quadspi to use spi-mem framework
spi: Move cadence-quadspi driver to drivers/spi/

Vignesh Raghavendra (6):
mtd: spi-nor: cadence-quadspi: Make driver independent of flash
geometry
mtd: spi-nor: cadence-quadspi: Provide a way to disable DAC mode
mtd: spi-nor: cadence-quadspi: Don't initialize rx_dma_complete on
failure
mtd: spi-nor: cadence-quadspi: Fix error path on failure to acquire
reset lines
mtd: spi-nor: cadence-quadspi: Handle probe deferral while requesting
DMA channel
mtd: spi-nor: cadence-quadspi: Drop redundant WREN in erase path

 drivers/mtd/spi-nor/controllers/Kconfig       |  11 -
 drivers/mtd/spi-nor/controllers/Makefile      |   1 -
 drivers/spi/Kconfig                           |  11 +
 drivers/spi/Makefile                          |   1 +
 .../spi-cadence-quadspi.c}                    | 541 +++++++-----------
 5 files changed, 222 insertions(+), 343 deletions(-)
 rename drivers/{mtd/spi-nor/controllers/cadence-quadspi.c => spi/spi-cadence-quadspi.c} (74%)
Signature · 1 line
2.26.2
author maintainer
#1 lore raw

PATCH v3 1/8 mtd: spi-nor: cadence-quadspi: Make driver independent of flash geometry

Drop configuration of Flash size, erase size and page size configuration. Flash size is needed only if using AHB decoder (BIT 23 of CONFIG_REG) which is not used by the driver.
Erase size and page size are needed if IP is configured to send WREN automatically. But since SPI NOR layer takes care of sending WREN, there is no need to configure these fields either.

Therefore drop these in preparation to move the driver to spi-mem framework where flash geometry is not visible to controller driver.

---
 .../mtd/spi-nor/controllers/cadence-quadspi.c | 36 +------------------
 1 file changed, 1 insertion(+), 35 deletions(-)
drivers/mtd/spi-nor/controllers/cadence-quadspi.c +1 -35
index 494dcab4aaaa..9b8554d44fac 100644
@@ -77,9 +77,6 @@ struct cqspi_st {
 	dma_addr_t		mmap_phys_base;
 
 	int			current_cs;
-	int			current_page_size;
-	int			current_erase_size;
-	int			current_addr_width;
 	unsigned long		master_ref_clk_hz;
 	bool			is_decoded_cs;
 	u32			fifo_depth;
@@ -736,32 +733,6 @@ static void cqspi_chipselect(struct spi_nor *nor)
 	writel(reg, reg_base + CQSPI_REG_CONFIG);
 }
 
-static void cqspi_configure_cs_and_sizes(struct spi_nor *nor)
-{
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
-	struct cqspi_st *cqspi = f_pdata->cqspi;
-	void __iomem *iobase = cqspi->iobase;
-	unsigned int reg;
-
-	/* configure page size and block size. */
-	reg = readl(iobase + CQSPI_REG_SIZE);
-	reg &= ~(CQSPI_REG_SIZE_PAGE_MASK << CQSPI_REG_SIZE_PAGE_LSB);
-	reg &= ~(CQSPI_REG_SIZE_BLOCK_MASK << CQSPI_REG_SIZE_BLOCK_LSB);
-	reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
-	reg |= (nor->page_size << CQSPI_REG_SIZE_PAGE_LSB);
-	reg |= (ilog2(nor->mtd.erasesize) << CQSPI_REG_SIZE_BLOCK_LSB);
-	reg |= (nor->addr_width - 1);
-	writel(reg, iobase + CQSPI_REG_SIZE);
-
-	/* configure the chip select */
-	cqspi_chipselect(nor);
-
-	/* Store the new configuration of the controller */
-	cqspi->current_page_size = nor->page_size;
-	cqspi->current_erase_size = nor->mtd.erasesize;
-	cqspi->current_addr_width = nor->addr_width;
-}
-
 static unsigned int calculate_ticks_for_ns(const unsigned int ref_clk_hz,
 					   const unsigned int ns_val)
 {
@@ -867,18 +838,13 @@ static void cqspi_configure(struct spi_nor *nor)
 	int switch_cs = (cqspi->current_cs != f_pdata->cs);
 	int switch_ck = (cqspi->sclk != sclk);
 
-	if ((cqspi->current_page_size != nor->page_size) ||
-	    (cqspi->current_erase_size != nor->mtd.erasesize) ||
-	    (cqspi->current_addr_width != nor->addr_width))
-		switch_cs = 1;
-
 	if (switch_cs || switch_ck)
 		cqspi_controller_enable(cqspi, 0);
 
 	/* Switch chip select. */
 	if (switch_cs) {
 		cqspi->current_cs = f_pdata->cs;
-		cqspi_configure_cs_and_sizes(nor);
+		cqspi_chipselect(nor);
 	}
 
 	/* Setup baudrate divisor and delays */
Signature · 1 line
2.26.2
author maintainer
#2 lore raw

PATCH v3 2/8 mtd: spi-nor: cadence-quadspi: Provide a way to disable DAC mode

In reply to Vignesh Raghavendra

Currently direct access mode is used on platforms that have AHB window (memory mapped window) larger than flash size. This feature is limited to TI platforms as non TI platforms have < 1MB of AHB window. Therefore introduce a driver quirk to disable DAC mode and set it for non TI compatibles. This is in preparation to move to spi-mem framework where flash geometry cannot be known.

---
 drivers/mtd/spi-nor/controllers/cadence-quadspi.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/mtd/spi-nor/controllers/cadence-quadspi.c +4 -1
index 9b8554d44fac..8a9e17f79d8d 100644
@@ -34,6 +34,7 @@
 
 /* Quirks */
 #define CQSPI_NEEDS_WR_DELAY		BIT(0)
+#define CQSPI_DISABLE_DAC_MODE		BIT(1)
 
 /* Capabilities mask */
 #define CQSPI_BASE_HWCAPS_MASK					\
@@ -1261,7 +1262,8 @@ static int cqspi_setup_flash(struct cqspi_st *cqspi, struct device_node *np)
 
 		f_pdata->registered = true;
 
-		if (mtd->size <= cqspi->ahb_size) {
+		if (mtd->size <= cqspi->ahb_size &&
+		    !(ddata->quirks & CQSPI_DISABLE_DAC_MODE)) {
 			f_pdata->use_direct_mode = true;
 			dev_dbg(nor->dev, "using direct mode for %s\n",
 				mtd->name);
@@ -1457,6 +1459,7 @@ static const struct dev_pm_ops cqspi__dev_pm_ops = {
 
 static const struct cqspi_driver_platdata cdns_qspi = {
 	.hwcaps_mask = CQSPI_BASE_HWCAPS_MASK,
+	.quirks = CQSPI_DISABLE_DAC_MODE,
 };
 
 static const struct cqspi_driver_platdata k2g_qspi = {
Signature · 1 line
2.26.2
author maintainer
#3 lore raw

PATCH v3 3/8 mtd: spi-nor: cadence-quadspi: Don't initialize rx_dma_complete on failure

In reply to Vignesh Raghavendra

If driver fails to acquire DMA channel then don't initialize rx_dma_complete struct as it won't be used.

---
 drivers/mtd/spi-nor/controllers/cadence-quadspi.c | 1 +
 1 file changed, 1 insertion(+)
drivers/mtd/spi-nor/controllers/cadence-quadspi.c +1 -0
index 8a9e17f79d8d..379e22c11c87 100644
@@ -1180,6 +1180,7 @@ static void cqspi_request_mmap_dma(struct cqspi_st *cqspi)
 	if (IS_ERR(cqspi->rx_chan)) {
 		dev_err(&cqspi->pdev->dev, "No Rx DMA available\n");
 		cqspi->rx_chan = NULL;
+		return;
 	}
 	init_completion(&cqspi->rx_dma_complete);
 }
Signature · 1 line
2.26.2
author maintainer
#4 lore raw

PATCH v3 4/8 mtd: spi-nor: cadence-quadspi: Fix error path on failure to acquire reset lines

In reply to Vignesh Raghavendra

Make sure to undo the prior changes done by the driver when exiting due to failure to acquire reset lines.

---
 drivers/mtd/spi-nor/controllers/cadence-quadspi.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/mtd/spi-nor/controllers/cadence-quadspi.c +4 -4
index 379e22c11c87..608ca657ff7f 100644
@@ -1359,13 +1359,13 @@ static int cqspi_probe(struct platform_device *pdev)
 	rstc = devm_reset_control_get_optional_exclusive(dev, "qspi");
 	if (IS_ERR(rstc)) {
 		dev_err(dev, "Cannot get QSPI reset.\n");
-		return PTR_ERR(rstc);
+		goto probe_reset_failed;
 	}
 
 	rstc_ocp = devm_reset_control_get_optional_exclusive(dev, "qspi-ocp");
 	if (IS_ERR(rstc_ocp)) {
 		dev_err(dev, "Cannot get QSPI OCP reset.\n");
-		return PTR_ERR(rstc_ocp);
+		goto probe_reset_failed;
 	}
 
 	reset_control_assert(rstc);
@@ -1384,7 +1384,7 @@ static int cqspi_probe(struct platform_device *pdev)
 			       pdev->name, cqspi);
 	if (ret) {
 		dev_err(dev, "Cannot request IRQ.\n");
-		goto probe_irq_failed;
+		goto probe_reset_failed;
 	}
 
 	cqspi_wait_idle(cqspi);
@@ -1401,7 +1401,7 @@ static int cqspi_probe(struct platform_device *pdev)
 	return ret;
 probe_setup_failed:
 	cqspi_controller_enable(cqspi, 0);
-probe_irq_failed:
+probe_reset_failed:
 	clk_disable_unprepare(cqspi->clk);
 probe_clk_failed:
 	pm_runtime_put_sync(dev);
Signature · 1 line
2.26.2
author maintainer
#5 lore raw

PATCH v3 5/8 mtd: spi-nor: cadence-quadspi: Handle probe deferral while requesting DMA channel

In reply to Vignesh Raghavendra

dma_request_chan_by_mask() can throw EPROBE_DEFER if DMA provider is not yet probed. Currently driver just falls back to using PIO mode (which is less efficient) in this case. Instead return probe deferral error as is so that driver will be re probed once DMA provider is available.

---
 .../mtd/spi-nor/controllers/cadence-quadspi.c  | 18 +++++++++++++-----
 1 file changed, 13 insertions(+), 5 deletions(-)
drivers/mtd/spi-nor/controllers/cadence-quadspi.c +13 -5
index 608ca657ff7f..0570ebca135a 100644
@@ -1169,7 +1169,7 @@ static void cqspi_controller_init(struct cqspi_st *cqspi)
 	cqspi_controller_enable(cqspi, 1);
 }
 
-static void cqspi_request_mmap_dma(struct cqspi_st *cqspi)
+static int cqspi_request_mmap_dma(struct cqspi_st *cqspi)
 {
 	dma_cap_mask_t mask;
 
@@ -1178,11 +1178,16 @@ static void cqspi_request_mmap_dma(struct cqspi_st *cqspi)
 
 	cqspi->rx_chan = dma_request_chan_by_mask(&mask);
 	if (IS_ERR(cqspi->rx_chan)) {
-		dev_err(&cqspi->pdev->dev, "No Rx DMA available\n");
+		int ret = PTR_ERR(cqspi->rx_chan);
+
+		if (ret != -EPROBE_DEFER)
+			dev_err(&cqspi->pdev->dev, "No Rx DMA available\n");
 		cqspi->rx_chan = NULL;
-		return;
+		return ret;
 	}
 	init_completion(&cqspi->rx_dma_complete);
+
+	return 0;
 }
 
 static const struct spi_nor_controller_ops cqspi_controller_ops = {
@@ -1269,8 +1274,11 @@ static int cqspi_setup_flash(struct cqspi_st *cqspi, struct device_node *np)
 			dev_dbg(nor->dev, "using direct mode for %s\n",
 				mtd->name);
 
-			if (!cqspi->rx_chan)
-				cqspi_request_mmap_dma(cqspi);
+			if (!cqspi->rx_chan) {
+				ret = cqspi_request_mmap_dma(cqspi);
+				if (ret == -EPROBE_DEFER)
+					goto err;
+			}
 		}
 	}
 
Signature · 1 line
2.26.2
Reviewed-by on v3 5/8
#6 lore raw

Re: [PATCH v3 5/8] mtd: spi-nor: cadence-quadspi: Handle probe deferral while requesting DMA channel

Quoted 10 lines · EEST Vignesh Raghavendra

dma_request_chan_by_mask() can throw EPROBE_DEFER if DMA provider is not yet probed. Currently driver just falls back to using PIO mode (which is less efficient) in this case. Instead return probe deferral error as is so that driver will be re probed once DMA provider is available.

---
 .../mtd/spi-nor/controllers/cadence-quadspi.c  | 18 +++++++++++++-----
 1 file changed, 13 insertions(+), 5 deletions(-)
author maintainer
#7 lore raw

PATCH v3 6/8 mtd: spi-nor: cadence-quadspi: Drop redundant WREN in erase path

In reply to Vignesh Raghavendra

Drop redundant WREN command in cqspi_erase() as SPI NOR core takes care of sending WREN command before sending erase command.

---
 drivers/mtd/spi-nor/controllers/cadence-quadspi.c | 5 -----
 1 file changed, 5 deletions(-)
drivers/mtd/spi-nor/controllers/cadence-quadspi.c +0 -5
index 0570ebca135a..6b1cbad25e3f 100644
@@ -1016,11 +1016,6 @@ static int cqspi_erase(struct spi_nor *nor, loff_t offs)
 	if (ret)
 		return ret;
 
-	/* Send write enable, then erase commands. */
-	ret = nor->controller_ops->write_reg(nor, SPINOR_OP_WREN, NULL, 0);
-	if (ret)
-		return ret;
-
 	/* Set up command buffer. */
 	ret = cqspi_command_write_addr(nor, nor->erase_opcode, offs);
 	if (ret)
Signature · 1 line
2.26.2
Reviewed-by on v3 6/8
#8 lore raw

Re: [PATCH v3 6/8] mtd: spi-nor: cadence-quadspi: Drop redundant WREN in erase path

Quoted 7 lines · EEST Vignesh Raghavendra

Drop redundant WREN command in cqspi_erase() as SPI NOR core takes care of sending WREN command before sending erase command.

---
 drivers/mtd/spi-nor/controllers/cadence-quadspi.c | 5 -----
 1 file changed, 5 deletions(-)
author maintainer
#9 lore raw

PATCH v3 7/8 mtd: spi-nor: Convert cadence-quadspi to use spi-mem framework

In reply to Vignesh Raghavendra

From: Ramuthevar Vadivel Murugan <[email protected]>

Move cadence-quadspi driver to use spi-mem framework. This is required to make the driver support for SPI NAND flashes in future.

Driver is feature compliant with existing SPI NOR version.

---
 .../mtd/spi-nor/controllers/cadence-quadspi.c | 476 +++++++-----------
 1 file changed, 191 insertions(+), 285 deletions(-)
drivers/mtd/spi-nor/controllers/cadence-quadspi.c +191 -285
index 6b1cbad25e3f..c12a1c0191b9 100644
@@ -3,6 +3,8 @@
  * Driver for Cadence QSPI Controller
  *
  * Copyright Altera Corporation (C) 2012-2014. All rights reserved.
+ * Copyright Intel Corporation (C) 2019-2020. All rights reserved.
+ * Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com
  */
 #include <linux/clk.h>
 #include <linux/completion.h>
@@ -17,9 +19,6 @@
 #include <linux/jiffies.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/spi-nor.h>
 #include <linux/of_device.h>
 #include <linux/of.h>
 #include <linux/platform_device.h>
@@ -27,6 +26,7 @@
 #include <linux/reset.h>
 #include <linux/sched.h>
 #include <linux/spi/spi.h>
+#include <linux/spi/spi-mem.h>
 #include <linux/timer.h>
 
 #define CQSPI_NAME			"cadence-qspi"
@@ -36,16 +36,12 @@
 #define CQSPI_NEEDS_WR_DELAY		BIT(0)
 #define CQSPI_DISABLE_DAC_MODE		BIT(1)
 
-/* Capabilities mask */
-#define CQSPI_BASE_HWCAPS_MASK					\
-	(SNOR_HWCAPS_READ | SNOR_HWCAPS_READ_FAST |		\
-	SNOR_HWCAPS_READ_1_1_2 | SNOR_HWCAPS_READ_1_1_4 |	\
-	SNOR_HWCAPS_PP)
+/* Capabilities */
+#define CQSPI_SUPPORTS_OCTAL		BIT(0)
 
 struct cqspi_st;
 
 struct cqspi_flash_pdata {
-	struct spi_nor	nor;
 	struct cqspi_st	*cqspi;
 	u32		clk_rate;
 	u32		read_delay;
@@ -57,8 +53,6 @@ struct cqspi_flash_pdata {
 	u8		addr_width;
 	u8		data_width;
 	u8		cs;
-	bool		registered;
-	bool		use_direct_mode;
 };
 
 struct cqspi_st {
@@ -71,7 +65,6 @@ struct cqspi_st {
 	void __iomem		*ahb_base;
 	resource_size_t		ahb_size;
 	struct completion	transfer_complete;
-	struct mutex		bus_mutex;
 
 	struct dma_chan		*rx_chan;
 	struct completion	rx_dma_complete;
@@ -85,6 +78,7 @@ struct cqspi_st {
 	bool			rclk_en;
 	u32			trigger_address;
 	u32			wr_delay;
+	bool			use_direct_mode;
 	struct cqspi_flash_pdata f_pdata[CQSPI_MAX_CHIPSELECT];
 };
 
@@ -283,9 +277,8 @@ static irqreturn_t cqspi_irq_handler(int this_irq, void *dev)
 	return IRQ_HANDLED;
 }
 
-static unsigned int cqspi_calc_rdreg(struct spi_nor *nor)
+static unsigned int cqspi_calc_rdreg(struct cqspi_flash_pdata *f_pdata)
 {
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
 	u32 rdreg = 0;
 
 	rdreg |= f_pdata->inst_width << CQSPI_REG_RD_INSTR_TYPE_INSTR_LSB;
@@ -352,19 +345,21 @@ static int cqspi_exec_flash_cmd(struct cqspi_st *cqspi, unsigned int reg)
 	return cqspi_wait_idle(cqspi);
 }
 
-static int cqspi_command_read(struct spi_nor *nor, u8 opcode,
-			      u8 *rxbuf, size_t n_rx)
+static int cqspi_command_read(struct cqspi_flash_pdata *f_pdata,
+			      const struct spi_mem_op *op)
 {
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
 	struct cqspi_st *cqspi = f_pdata->cqspi;
 	void __iomem *reg_base = cqspi->iobase;
+	u8 *rxbuf = op->data.buf.in;
+	u8 opcode = op->cmd.opcode;
+	size_t n_rx = op->data.nbytes;
 	unsigned int rdreg;
 	unsigned int reg;
 	size_t read_len;
 	int status;
 
 	if (!n_rx || n_rx > CQSPI_STIG_DATA_LEN_MAX || !rxbuf) {
-		dev_err(nor->dev,
+		dev_err(&cqspi->pdev->dev,
 			"Invalid input argument, len %zu rxbuf 0x%p\n",
 			n_rx, rxbuf);
 		return -EINVAL;
@@ -372,7 +367,7 @@ static int cqspi_command_read(struct spi_nor *nor, u8 opcode,
 
 	reg = opcode << CQSPI_REG_CMDCTRL_OPCODE_LSB;
 
-	rdreg = cqspi_calc_rdreg(nor);
+	rdreg = cqspi_calc_rdreg(f_pdata);
 	writel(rdreg, reg_base + CQSPI_REG_RD_INSTR);
 
 	reg |= (0x1 << CQSPI_REG_CMDCTRL_RD_EN_LSB);
@@ -401,25 +396,36 @@ static int cqspi_command_read(struct spi_nor *nor, u8 opcode,
 	return 0;
 }
 
-static int cqspi_command_write(struct spi_nor *nor, const u8 opcode,
-			       const u8 *txbuf, size_t n_tx)
+static int cqspi_command_write(struct cqspi_flash_pdata *f_pdata,
+			       const struct spi_mem_op *op)
 {
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
 	struct cqspi_st *cqspi = f_pdata->cqspi;
 	void __iomem *reg_base = cqspi->iobase;
+	const u8 opcode = op->cmd.opcode;
+	const u8 *txbuf = op->data.buf.out;
+	size_t n_tx = op->data.nbytes;
 	unsigned int reg;
 	unsigned int data;
 	size_t write_len;
-	int ret;
 
 	if (n_tx > CQSPI_STIG_DATA_LEN_MAX || (n_tx && !txbuf)) {
-		dev_err(nor->dev,
+		dev_err(&cqspi->pdev->dev,
 			"Invalid input argument, cmdlen %zu txbuf 0x%p\n",
 			n_tx, txbuf);
 		return -EINVAL;
 	}
 
 	reg = opcode << CQSPI_REG_CMDCTRL_OPCODE_LSB;
+
+	if (op->addr.nbytes) {
+		reg |= (0x1 << CQSPI_REG_CMDCTRL_ADDR_EN_LSB);
+		reg |= ((op->addr.nbytes - 1) &
+			CQSPI_REG_CMDCTRL_ADD_BYTES_MASK)
+			<< CQSPI_REG_CMDCTRL_ADD_BYTES_LSB;
+
+		writel(op->addr.val, reg_base + CQSPI_REG_CMDADDRESS);
+	}
+
 	if (n_tx) {
 		reg |= (0x1 << CQSPI_REG_CMDCTRL_WR_EN_LSB);
 		reg |= ((n_tx - 1) & CQSPI_REG_CMDCTRL_WR_BYTES_MASK)
@@ -437,73 +443,46 @@ static int cqspi_command_write(struct spi_nor *nor, const u8 opcode,
 			writel(data, reg_base + CQSPI_REG_CMDWRITEDATAUPPER);
 		}
 	}
-	ret = cqspi_exec_flash_cmd(cqspi, reg);
-	return ret;
-}
-
-static int cqspi_command_write_addr(struct spi_nor *nor,
-				    const u8 opcode, const unsigned int addr)
-{
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
-	struct cqspi_st *cqspi = f_pdata->cqspi;
-	void __iomem *reg_base = cqspi->iobase;
-	unsigned int reg;
-
-	reg = opcode << CQSPI_REG_CMDCTRL_OPCODE_LSB;
-	reg |= (0x1 << CQSPI_REG_CMDCTRL_ADDR_EN_LSB);
-	reg |= ((nor->addr_width - 1) & CQSPI_REG_CMDCTRL_ADD_BYTES_MASK)
-		<< CQSPI_REG_CMDCTRL_ADD_BYTES_LSB;
-
-	writel(addr, reg_base + CQSPI_REG_CMDADDRESS);
 
 	return cqspi_exec_flash_cmd(cqspi, reg);
 }
 
-static int cqspi_read_setup(struct spi_nor *nor)
+static int cqspi_read_setup(struct cqspi_flash_pdata *f_pdata,
+			    const struct spi_mem_op *op)
 {
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
 	struct cqspi_st *cqspi = f_pdata->cqspi;
 	void __iomem *reg_base = cqspi->iobase;
 	unsigned int dummy_clk = 0;
 	unsigned int reg;
 
-	reg = nor->read_opcode << CQSPI_REG_RD_INSTR_OPCODE_LSB;
-	reg |= cqspi_calc_rdreg(nor);
+	reg = op->cmd.opcode << CQSPI_REG_RD_INSTR_OPCODE_LSB;
+	reg |= cqspi_calc_rdreg(f_pdata);
 
 	/* Setup dummy clock cycles */
-	dummy_clk = nor->read_dummy;
+	dummy_clk = op->dummy.nbytes * 8;
 	if (dummy_clk > CQSPI_DUMMY_CLKS_MAX)
 		dummy_clk = CQSPI_DUMMY_CLKS_MAX;
 
-	if (dummy_clk / 8) {
-		reg |= (1 << CQSPI_REG_RD_INSTR_MODE_EN_LSB);
-		/* Set mode bits high to ensure chip doesn't enter XIP */
-		writel(0xFF, reg_base + CQSPI_REG_MODE_BIT);
-
-		/* Need to subtract the mode byte (8 clocks). */
-		if (f_pdata->inst_width != CQSPI_INST_TYPE_QUAD)
-			dummy_clk -= 8;
-
-		if (dummy_clk)
-			reg |= (dummy_clk & CQSPI_REG_RD_INSTR_DUMMY_MASK)
-			       << CQSPI_REG_RD_INSTR_DUMMY_LSB;
-	}
+	if (dummy_clk)
+		reg |= (dummy_clk & CQSPI_REG_RD_INSTR_DUMMY_MASK)
+		       << CQSPI_REG_RD_INSTR_DUMMY_LSB;
 
 	writel(reg, reg_base + CQSPI_REG_RD_INSTR);
 
 	/* Set address width */
 	reg = readl(reg_base + CQSPI_REG_SIZE);
 	reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
-	reg |= (nor->addr_width - 1);
+	reg |= (op->addr.nbytes - 1);
 	writel(reg, reg_base + CQSPI_REG_SIZE);
 	return 0;
 }
 
-static int cqspi_indirect_read_execute(struct spi_nor *nor, u8 *rxbuf,
-				       loff_t from_addr, const size_t n_rx)
+static int cqspi_indirect_read_execute(struct cqspi_flash_pdata *f_pdata,
+				       u8 *rxbuf, loff_t from_addr,
+				       const size_t n_rx)
 {
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
 	struct cqspi_st *cqspi = f_pdata->cqspi;
+	struct device *dev = &cqspi->pdev->dev;
 	void __iomem *reg_base = cqspi->iobase;
 	void __iomem *ahb_base = cqspi->ahb_base;
 	unsigned int remaining = n_rx;
@@ -526,13 +505,13 @@ static int cqspi_indirect_read_execute(struct spi_nor *nor, u8 *rxbuf,
 
 	while (remaining > 0) {
 		if (!wait_for_completion_timeout(&cqspi->transfer_complete,
-				msecs_to_jiffies(CQSPI_READ_TIMEOUT_MS)))
+						 msecs_to_jiffies(CQSPI_READ_TIMEOUT_MS)))
 			ret = -ETIMEDOUT;
 
 		bytes_to_read = cqspi_get_rd_sram_level(cqspi);
 
 		if (ret && bytes_to_read == 0) {
-			dev_err(nor->dev, "Indirect read timeout, no bytes\n");
+			dev_err(dev, "Indirect read timeout, no bytes\n");
 			goto failrd;
 		}
 
@@ -568,8 +547,7 @@ static int cqspi_indirect_read_execute(struct spi_nor *nor, u8 *rxbuf,
 	ret = cqspi_wait_for_bit(reg_base + CQSPI_REG_INDIRECTRD,
 				 CQSPI_REG_INDIRECTRD_DONE_MASK, 0);
 	if (ret) {
-		dev_err(nor->dev,
-			"Indirect read completion error (%i)\n", ret);
+		dev_err(dev, "Indirect read completion error (%i)\n", ret);
 		goto failrd;
 	}
 
@@ -591,32 +569,32 @@ static int cqspi_indirect_read_execute(struct spi_nor *nor, u8 *rxbuf,
 	return ret;
 }
 
-static int cqspi_write_setup(struct spi_nor *nor)
+static int cqspi_write_setup(struct cqspi_flash_pdata *f_pdata,
+			     const struct spi_mem_op *op)
 {
 	unsigned int reg;
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
 	struct cqspi_st *cqspi = f_pdata->cqspi;
 	void __iomem *reg_base = cqspi->iobase;
 
 	/* Set opcode. */
-	reg = nor->program_opcode << CQSPI_REG_WR_INSTR_OPCODE_LSB;
+	reg = op->cmd.opcode << CQSPI_REG_WR_INSTR_OPCODE_LSB;
 	writel(reg, reg_base + CQSPI_REG_WR_INSTR);
-	reg = cqspi_calc_rdreg(nor);
+	reg = cqspi_calc_rdreg(f_pdata);
 	writel(reg, reg_base + CQSPI_REG_RD_INSTR);
 
 	reg = readl(reg_base + CQSPI_REG_SIZE);
 	reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
-	reg |= (nor->addr_width - 1);
+	reg |= (op->addr.nbytes - 1);
 	writel(reg, reg_base + CQSPI_REG_SIZE);
 	return 0;
 }
 
-static int cqspi_indirect_write_execute(struct spi_nor *nor, loff_t to_addr,
-					const u8 *txbuf, const size_t n_tx)
+static int cqspi_indirect_write_execute(struct cqspi_flash_pdata *f_pdata,
+					loff_t to_addr, const u8 *txbuf,
+					const size_t n_tx)
 {
-	const unsigned int page_size = nor->page_size;
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
 	struct cqspi_st *cqspi = f_pdata->cqspi;
+	struct device *dev = &cqspi->pdev->dev;
 	void __iomem *reg_base = cqspi->iobase;
 	unsigned int remaining = n_tx;
 	unsigned int write_bytes;
@@ -646,7 +624,7 @@ static int cqspi_indirect_write_execute(struct spi_nor *nor, loff_t to_addr,
 	while (remaining > 0) {
 		size_t write_words, mod_bytes;
 
-		write_bytes = remaining > page_size ? page_size : remaining;
+		write_bytes = remaining;
 		write_words = write_bytes / 4;
 		mod_bytes = write_bytes % 4;
 		/* Write 4 bytes at a time then single bytes. */
@@ -663,8 +641,8 @@ static int cqspi_indirect_write_execute(struct spi_nor *nor, loff_t to_addr,
 		}
 
 		if (!wait_for_completion_timeout(&cqspi->transfer_complete,
-					msecs_to_jiffies(CQSPI_TIMEOUT_MS))) {
-			dev_err(nor->dev, "Indirect write timeout\n");
+						 msecs_to_jiffies(CQSPI_TIMEOUT_MS))) {
+			dev_err(dev, "Indirect write timeout\n");
 			ret = -ETIMEDOUT;
 			goto failwr;
 		}
@@ -679,8 +657,7 @@ static int cqspi_indirect_write_execute(struct spi_nor *nor, loff_t to_addr,
 	ret = cqspi_wait_for_bit(reg_base + CQSPI_REG_INDIRECTWR,
 				 CQSPI_REG_INDIRECTWR_DONE_MASK, 0);
 	if (ret) {
-		dev_err(nor->dev,
-			"Indirect write completion error (%i)\n", ret);
+		dev_err(dev, "Indirect write completion error (%i)\n", ret);
 		goto failwr;
 	}
 
@@ -704,9 +681,8 @@ static int cqspi_indirect_write_execute(struct spi_nor *nor, loff_t to_addr,
 	return ret;
 }
 
-static void cqspi_chipselect(struct spi_nor *nor)
+static void cqspi_chipselect(struct cqspi_flash_pdata *f_pdata)
 {
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
 	struct cqspi_st *cqspi = f_pdata->cqspi;
 	void __iomem *reg_base = cqspi->iobase;
 	unsigned int chip_select = f_pdata->cs;
@@ -745,9 +721,8 @@ static unsigned int calculate_ticks_for_ns(const unsigned int ref_clk_hz,
 	return ticks;
 }
 
-static void cqspi_delay(struct spi_nor *nor)
+static void cqspi_delay(struct cqspi_flash_pdata *f_pdata)
 {
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
 	struct cqspi_st *cqspi = f_pdata->cqspi;
 	void __iomem *iobase = cqspi->iobase;
 	const unsigned int ref_clk_hz = cqspi->master_ref_clk_hz;
@@ -831,11 +806,10 @@ static void cqspi_controller_enable(struct cqspi_st *cqspi, bool enable)
 	writel(reg, reg_base + CQSPI_REG_CONFIG);
 }
 
-static void cqspi_configure(struct spi_nor *nor)
+static void cqspi_configure(struct cqspi_flash_pdata *f_pdata,
+			    unsigned long sclk)
 {
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
 	struct cqspi_st *cqspi = f_pdata->cqspi;
-	const unsigned int sclk = f_pdata->clk_rate;
 	int switch_cs = (cqspi->current_cs != f_pdata->cs);
 	int switch_ck = (cqspi->sclk != sclk);
 
@@ -845,14 +819,14 @@ static void cqspi_configure(struct spi_nor *nor)
 	/* Switch chip select. */
 	if (switch_cs) {
 		cqspi->current_cs = f_pdata->cs;
-		cqspi_chipselect(nor);
+		cqspi_chipselect(f_pdata);
 	}
 
 	/* Setup baudrate divisor and delays */
 	if (switch_ck) {
 		cqspi->sclk = sclk;
 		cqspi_config_baudrate_div(cqspi);
-		cqspi_delay(nor);
+		cqspi_delay(f_pdata);
 		cqspi_readdata_capture(cqspi, !cqspi->rclk_en,
 				       f_pdata->read_delay);
 	}
@@ -861,26 +835,25 @@ static void cqspi_configure(struct spi_nor *nor)
 		cqspi_controller_enable(cqspi, 1);
 }
 
-static int cqspi_set_protocol(struct spi_nor *nor, const int read)
+static int cqspi_set_protocol(struct cqspi_flash_pdata *f_pdata,
+			      const struct spi_mem_op *op)
 {
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
-
 	f_pdata->inst_width = CQSPI_INST_TYPE_SINGLE;
 	f_pdata->addr_width = CQSPI_INST_TYPE_SINGLE;
 	f_pdata->data_width = CQSPI_INST_TYPE_SINGLE;
 
-	if (read) {
-		switch (nor->read_proto) {
-		case SNOR_PROTO_1_1_1:
+	if (op->data.dir == SPI_MEM_DATA_IN) {
+		switch (op->data.buswidth) {
+		case 1:
 			f_pdata->data_width = CQSPI_INST_TYPE_SINGLE;
 			break;
-		case SNOR_PROTO_1_1_2:
+		case 2:
 			f_pdata->data_width = CQSPI_INST_TYPE_DUAL;
 			break;
-		case SNOR_PROTO_1_1_4:
+		case 4:
 			f_pdata->data_width = CQSPI_INST_TYPE_QUAD;
 			break;
-		case SNOR_PROTO_1_1_8:
+		case 8:
 			f_pdata->data_width = CQSPI_INST_TYPE_OCTAL;
 			break;
 		default:
@@ -888,36 +861,32 @@ static int cqspi_set_protocol(struct spi_nor *nor, const int read)
 		}
 	}
 
-	cqspi_configure(nor);
-
 	return 0;
 }
 
-static ssize_t cqspi_write(struct spi_nor *nor, loff_t to,
-			   size_t len, const u_char *buf)
+static ssize_t cqspi_write(struct cqspi_flash_pdata *f_pdata,
+			   const struct spi_mem_op *op)
 {
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
 	struct cqspi_st *cqspi = f_pdata->cqspi;
+	loff_t to = op->addr.val;
+	size_t len = op->data.nbytes;
+	const u_char *buf = op->data.buf.out;
 	int ret;
 
-	ret = cqspi_set_protocol(nor, 0);
+	ret = cqspi_set_protocol(f_pdata, op);
 	if (ret)
 		return ret;
 
-	ret = cqspi_write_setup(nor);
+	ret = cqspi_write_setup(f_pdata, op);
 	if (ret)
 		return ret;
 
-	if (f_pdata->use_direct_mode) {
+	if (cqspi->use_direct_mode && ((to + len) <= cqspi->ahb_size)) {
 		memcpy_toio(cqspi->ahb_base + to, buf, len);
-		ret = cqspi_wait_idle(cqspi);
-	} else {
-		ret = cqspi_indirect_write_execute(nor, to, buf, len);
+		return cqspi_wait_idle(cqspi);
 	}
-	if (ret)
-		return ret;
 
-	return len;
+	return cqspi_indirect_write_execute(f_pdata, to, buf, len);
 }
 
 static void cqspi_rx_dma_callback(void *param)
@@ -927,11 +896,11 @@ static void cqspi_rx_dma_callback(void *param)
 	complete(&cqspi->rx_dma_complete);
 }
 
-static int cqspi_direct_read_execute(struct spi_nor *nor, u_char *buf,
-				     loff_t from, size_t len)
+static int cqspi_direct_read_execute(struct cqspi_flash_pdata *f_pdata,
+				     u_char *buf, loff_t from, size_t len)
 {
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
 	struct cqspi_st *cqspi = f_pdata->cqspi;
+	struct device *dev = &cqspi->pdev->dev;
 	enum dma_ctrl_flags flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
 	dma_addr_t dma_src = (dma_addr_t)cqspi->mmap_phys_base + from;
 	int ret = 0;
@@ -944,15 +913,15 @@ static int cqspi_direct_read_execute(struct spi_nor *nor, u_char *buf,
 		return 0;
 	}
 
-	dma_dst = dma_map_single(nor->dev, buf, len, DMA_FROM_DEVICE);
-	if (dma_mapping_error(nor->dev, dma_dst)) {
-		dev_err(nor->dev, "dma mapping failed\n");
+	dma_dst = dma_map_single(dev, buf, len, DMA_FROM_DEVICE);
+	if (dma_mapping_error(dev, dma_dst)) {
+		dev_err(dev, "dma mapping failed\n");
 		return -ENOMEM;
 	}
 	tx = dmaengine_prep_dma_memcpy(cqspi->rx_chan, dma_dst, dma_src,
 				       len, flags);
 	if (!tx) {
-		dev_err(nor->dev, "device_prep_dma_memcpy error\n");
+		dev_err(dev, "device_prep_dma_memcpy error\n");
 		ret = -EIO;
 		goto err_unmap;
 	}
@@ -964,7 +933,7 @@ static int cqspi_direct_read_execute(struct spi_nor *nor, u_char *buf,
 
 	ret = dma_submit_error(cookie);
 	if (ret) {
-		dev_err(nor->dev, "dma_submit_error %d\n", cookie);
+		dev_err(dev, "dma_submit_error %d\n", cookie);
 		ret = -EIO;
 		goto err_unmap;
 	}
@@ -973,94 +942,68 @@ static int cqspi_direct_read_execute(struct spi_nor *nor, u_char *buf,
 	if (!wait_for_completion_timeout(&cqspi->rx_dma_complete,
 					 msecs_to_jiffies(len))) {
 		dmaengine_terminate_sync(cqspi->rx_chan);
-		dev_err(nor->dev, "DMA wait_for_completion_timeout\n");
+		dev_err(dev, "DMA wait_for_completion_timeout\n");
 		ret = -ETIMEDOUT;
 		goto err_unmap;
 	}
 
 err_unmap:
-	dma_unmap_single(nor->dev, dma_dst, len, DMA_FROM_DEVICE);
+	dma_unmap_single(dev, dma_dst, len, DMA_FROM_DEVICE);
 
 	return ret;
 }
 
-static ssize_t cqspi_read(struct spi_nor *nor, loff_t from,
-			  size_t len, u_char *buf)
+static ssize_t cqspi_read(struct cqspi_flash_pdata *f_pdata,
+			  const struct spi_mem_op *op)
 {
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
+	struct cqspi_st *cqspi = f_pdata->cqspi;
+	loff_t from = op->addr.val;
+	size_t len = op->data.nbytes;
+	u_char *buf = op->data.buf.in;
 	int ret;
 
-	ret = cqspi_set_protocol(nor, 1);
+	ret = cqspi_set_protocol(f_pdata, op);
 	if (ret)
 		return ret;
 
-	ret = cqspi_read_setup(nor);
+	ret = cqspi_read_setup(f_pdata, op);
 	if (ret)
 		return ret;
 
-	if (f_pdata->use_direct_mode)
-		ret = cqspi_direct_read_execute(nor, buf, from, len);
-	else
-		ret = cqspi_indirect_read_execute(nor, buf, from, len);
-	if (ret)
-		return ret;
+	if (cqspi->use_direct_mode && ((from + len) <= cqspi->ahb_size))
+		return cqspi_direct_read_execute(f_pdata, buf, from, len);
 
-	return len;
+	return cqspi_indirect_read_execute(f_pdata, buf, from, len);
 }
 
-static int cqspi_erase(struct spi_nor *nor, loff_t offs)
+static int cqspi_mem_process(struct spi_mem *mem, const struct spi_mem_op *op)
 {
-	int ret;
-
-	ret = cqspi_set_protocol(nor, 0);
-	if (ret)
-		return ret;
-
-	/* Set up command buffer. */
-	ret = cqspi_command_write_addr(nor, nor->erase_opcode, offs);
-	if (ret)
-		return ret;
-
-	return 0;
-}
-
-static int cqspi_prep(struct spi_nor *nor)
-{
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
-	struct cqspi_st *cqspi = f_pdata->cqspi;
-
-	mutex_lock(&cqspi->bus_mutex);
-
-	return 0;
-}
+	struct cqspi_st *cqspi = spi_master_get_devdata(mem->spi->master);
+	struct cqspi_flash_pdata *f_pdata;
 
-static void cqspi_unprep(struct spi_nor *nor)
-{
-	struct cqspi_flash_pdata *f_pdata = nor->priv;
-	struct cqspi_st *cqspi = f_pdata->cqspi;
+	f_pdata = &cqspi->f_pdata[mem->spi->chip_select];
+	cqspi_configure(f_pdata, mem->spi->max_speed_hz);
 
-	mutex_unlock(&cqspi->bus_mutex);
-}
+	if (op->data.dir == SPI_MEM_DATA_IN && op->data.buf.in) {
+		if (!op->addr.nbytes)
+			return cqspi_command_read(f_pdata, op);
 
-static int cqspi_read_reg(struct spi_nor *nor, u8 opcode, u8 *buf, size_t len)
-{
-	int ret;
+		return cqspi_read(f_pdata, op);
+	}
 
-	ret = cqspi_set_protocol(nor, 0);
-	if (!ret)
-		ret = cqspi_command_read(nor, opcode, buf, len);
+	if (!op->addr.nbytes || !op->data.buf.out)
+		return cqspi_command_write(f_pdata, op);
 
-	return ret;
+	return cqspi_write(f_pdata, op);
 }
 
-static int cqspi_write_reg(struct spi_nor *nor, u8 opcode, const u8 *buf,
-			   size_t len)
+static int cqspi_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
 {
 	int ret;
 
-	ret = cqspi_set_protocol(nor, 0);
-	if (!ret)
-		ret = cqspi_command_write(nor, opcode, buf, len);
+	ret = cqspi_mem_process(mem, op);
+	if (ret)
+		dev_err(&mem->spi->dev, "operation failed with %d\n", ret);
 
 	return ret;
 }
@@ -1102,26 +1045,26 @@ static int cqspi_of_get_flash_pdata(struct platform_device *pdev,
 	return 0;
 }
 
-static int cqspi_of_get_pdata(struct platform_device *pdev)
+static int cqspi_of_get_pdata(struct cqspi_st *cqspi)
 {
-	struct device_node *np = pdev->dev.of_node;
-	struct cqspi_st *cqspi = platform_get_drvdata(pdev);
+	struct device *dev = &cqspi->pdev->dev;
+	struct device_node *np = dev->of_node;
 
 	cqspi->is_decoded_cs = of_property_read_bool(np, "cdns,is-decoded-cs");
 
 	if (of_property_read_u32(np, "cdns,fifo-depth", &cqspi->fifo_depth)) {
-		dev_err(&pdev->dev, "couldn't determine fifo-depth\n");
+		dev_err(dev, "couldn't determine fifo-depth\n");
 		return -ENXIO;
 	}
 
 	if (of_property_read_u32(np, "cdns,fifo-width", &cqspi->fifo_width)) {
-		dev_err(&pdev->dev, "couldn't determine fifo-width\n");
+		dev_err(dev, "couldn't determine fifo-width\n");
 		return -ENXIO;
 	}
 
 	if (of_property_read_u32(np, "cdns,trigger-address",
 				 &cqspi->trigger_address)) {
-		dev_err(&pdev->dev, "couldn't determine trigger-address\n");
+		dev_err(dev, "couldn't determine trigger-address\n");
 		return -ENXIO;
 	}
 
@@ -1185,47 +1128,30 @@ static int cqspi_request_mmap_dma(struct cqspi_st *cqspi)
 	return 0;
 }
 
-static const struct spi_nor_controller_ops cqspi_controller_ops = {
-	.prepare = cqspi_prep,
-	.unprepare = cqspi_unprep,
-	.read_reg = cqspi_read_reg,
-	.write_reg = cqspi_write_reg,
-	.read = cqspi_read,
-	.write = cqspi_write,
-	.erase = cqspi_erase,
+static const struct spi_controller_mem_ops cqspi_mem_ops = {
+	.exec_op = cqspi_exec_mem_op,
 };
 
-static int cqspi_setup_flash(struct cqspi_st *cqspi, struct device_node *np)
+static int cqspi_setup_flash(struct cqspi_st *cqspi)
 {
 	struct platform_device *pdev = cqspi->pdev;
 	struct device *dev = &pdev->dev;
-	const struct cqspi_driver_platdata *ddata;
-	struct spi_nor_hwcaps hwcaps;
+	struct device_node *np = dev->of_node;
 	struct cqspi_flash_pdata *f_pdata;
-	struct spi_nor *nor;
-	struct mtd_info *mtd;
 	unsigned int cs;
-	int i, ret;
-
-	ddata = of_device_get_match_data(dev);
-	if (!ddata) {
-		dev_err(dev, "Couldn't find driver data\n");
-		return -EINVAL;
-	}
-	hwcaps.mask = ddata->hwcaps_mask;
+	int ret;
 
 	/* Get flash device data */
 	for_each_available_child_of_node(dev->of_node, np) {
 		ret = of_property_read_u32(np, "reg", &cs);
 		if (ret) {
 			dev_err(dev, "Couldn't determine chip select.\n");
-			goto err;
+			return ret;
 		}
 
 		if (cs >= CQSPI_MAX_CHIPSELECT) {
-			ret = -EINVAL;
 			dev_err(dev, "Chip select %d out of range.\n", cs);
-			goto err;
+			return -EINVAL;
 		}
 
 		f_pdata = &cqspi->f_pdata[cs];
@@ -1234,90 +1160,51 @@ static int cqspi_setup_flash(struct cqspi_st *cqspi, struct device_node *np)
 
 		ret = cqspi_of_get_flash_pdata(pdev, f_pdata, np);
 		if (ret)
-			goto err;
-
-		nor = &f_pdata->nor;
-		mtd = &nor->mtd;
-
-		mtd->priv = nor;
-
-		nor->dev = dev;
-		spi_nor_set_flash_node(nor, np);
-		nor->priv = f_pdata;
-		nor->controller_ops = &cqspi_controller_ops;
-
-		mtd->name = devm_kasprintf(dev, GFP_KERNEL, "%s.%d",
-					   dev_name(dev), cs);
-		if (!mtd->name) {
-			ret = -ENOMEM;
-			goto err;
-		}
-
-		ret = spi_nor_scan(nor, NULL, &hwcaps);
-		if (ret)
-			goto err;
-
-		ret = mtd_device_register(mtd, NULL, 0);
-		if (ret)
-			goto err;
-
-		f_pdata->registered = true;
-
-		if (mtd->size <= cqspi->ahb_size &&
-		    !(ddata->quirks & CQSPI_DISABLE_DAC_MODE)) {
-			f_pdata->use_direct_mode = true;
-			dev_dbg(nor->dev, "using direct mode for %s\n",
-				mtd->name);
-
-			if (!cqspi->rx_chan) {
-				ret = cqspi_request_mmap_dma(cqspi);
-				if (ret == -EPROBE_DEFER)
-					goto err;
-			}
-		}
+			return ret;
 	}
 
 	return 0;
-
-err:
-	for (i = 0; i < CQSPI_MAX_CHIPSELECT; i++)
-		if (cqspi->f_pdata[i].registered)
-			mtd_device_unregister(&cqspi->f_pdata[i].nor.mtd);
-	return ret;
 }
 
 static int cqspi_probe(struct platform_device *pdev)
 {
-	struct device_node *np = pdev->dev.of_node;
+	const struct cqspi_driver_platdata *ddata;
+	struct reset_control *rstc, *rstc_ocp;
 	struct device *dev = &pdev->dev;
+	struct spi_master *master;
+	struct resource *res_ahb;
 	struct cqspi_st *cqspi;
 	struct resource *res;
-	struct resource *res_ahb;
-	struct reset_control *rstc, *rstc_ocp;
-	const struct cqspi_driver_platdata *ddata;
 	int ret;
 	int irq;
 
-	cqspi = devm_kzalloc(dev, sizeof(*cqspi), GFP_KERNEL);
-	if (!cqspi)
+	master = spi_alloc_master(&pdev->dev, sizeof(*cqspi));
+	if (!master) {
+		dev_err(&pdev->dev, "spi_alloc_master failed\n");
 		return -ENOMEM;
+	}
+	master->mode_bits = SPI_RX_QUAD | SPI_RX_DUAL;
+	master->mem_ops = &cqspi_mem_ops;
+	master->dev.of_node = pdev->dev.of_node;
+
+	cqspi = spi_master_get_devdata(master);
 
-	mutex_init(&cqspi->bus_mutex);
 	cqspi->pdev = pdev;
-	platform_set_drvdata(pdev, cqspi);
 
 	/* Obtain configuration from OF. */
-	ret = cqspi_of_get_pdata(pdev);
+	ret = cqspi_of_get_pdata(cqspi);
 	if (ret) {
 		dev_err(dev, "Cannot get mandatory OF data.\n");
-		return -ENODEV;
+		ret = -ENODEV;
+		goto probe_master_put;
 	}
 
 	/* Obtain QSPI clock. */
 	cqspi->clk = devm_clk_get(dev, NULL);
 	if (IS_ERR(cqspi->clk)) {
 		dev_err(dev, "Cannot claim QSPI clock.\n");
-		return PTR_ERR(cqspi->clk);
+		ret = PTR_ERR(cqspi->clk);
+		goto probe_master_put;
 	}
 
 	/* Obtain and remap controller address. */
@@ -1325,7 +1212,8 @@ static int cqspi_probe(struct platform_device *pdev)
 	cqspi->iobase = devm_ioremap_resource(dev, res);
 	if (IS_ERR(cqspi->iobase)) {
 		dev_err(dev, "Cannot remap controller address.\n");
-		return PTR_ERR(cqspi->iobase);
+		ret = PTR_ERR(cqspi->iobase);
+		goto probe_master_put;
 	}
 
 	/* Obtain and remap AHB address. */
@@ -1333,7 +1221,8 @@ static int cqspi_probe(struct platform_device *pdev)
 	cqspi->ahb_base = devm_ioremap_resource(dev, res_ahb);
 	if (IS_ERR(cqspi->ahb_base)) {
 		dev_err(dev, "Cannot remap AHB address.\n");
-		return PTR_ERR(cqspi->ahb_base);
+		ret = PTR_ERR(cqspi->ahb_base);
+		goto probe_master_put;
 	}
 	cqspi->mmap_phys_base = (dma_addr_t)res_ahb->start;
 	cqspi->ahb_size = resource_size(res_ahb);
@@ -1342,14 +1231,16 @@ static int cqspi_probe(struct platform_device *pdev)
 
 	/* Obtain IRQ line. */
 	irq = platform_get_irq(pdev, 0);
-	if (irq < 0)
-		return -ENXIO;
+	if (irq < 0) {
+		ret = -ENXIO;
+		goto probe_master_put;
+	}
 
 	pm_runtime_enable(dev);
 	ret = pm_runtime_get_sync(dev);
 	if (ret < 0) {
 		pm_runtime_put_noidle(dev);
-		return ret;
+		goto probe_master_put;
 	}
 
 	ret = clk_prepare_enable(cqspi->clk);
@@ -1379,9 +1270,15 @@ static int cqspi_probe(struct platform_device *pdev)
 
 	cqspi->master_ref_clk_hz = clk_get_rate(cqspi->clk);
 	ddata  = of_device_get_match_data(dev);
-	if (ddata && (ddata->quirks & CQSPI_NEEDS_WR_DELAY))
-		cqspi->wr_delay = 5 * DIV_ROUND_UP(NSEC_PER_SEC,
-						   cqspi->master_ref_clk_hz);
+	if (ddata) {
+		if (ddata->quirks & CQSPI_NEEDS_WR_DELAY)
+			cqspi->wr_delay = 5 * DIV_ROUND_UP(NSEC_PER_SEC,
+						cqspi->master_ref_clk_hz);
+		if (ddata->hwcaps_mask & CQSPI_SUPPORTS_OCTAL)
+			master->mode_bits |= SPI_RX_OCTAL;
+		if (!(ddata->quirks & CQSPI_DISABLE_DAC_MODE))
+			cqspi->use_direct_mode = true;
+	}
 
 	ret = devm_request_irq(dev, irq, cqspi_irq_handler, 0,
 			       pdev->name, cqspi);
@@ -1395,13 +1292,25 @@ static int cqspi_probe(struct platform_device *pdev)
 	cqspi->current_cs = -1;
 	cqspi->sclk = 0;
 
-	ret = cqspi_setup_flash(cqspi, np);
+	ret = cqspi_setup_flash(cqspi);
 	if (ret) {
-		dev_err(dev, "Cadence QSPI NOR probe failed %d\n", ret);
+		dev_err(dev, "failed to setup flash parameters %d\n", ret);
 		goto probe_setup_failed;
 	}
 
-	return ret;
+	if (cqspi->use_direct_mode) {
+		ret = cqspi_request_mmap_dma(cqspi);
+		if (ret == -EPROBE_DEFER)
+			goto probe_setup_failed;
+	}
+
+	ret = devm_spi_register_master(dev, master);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to register SPI ctlr %d\n", ret);
+		goto probe_setup_failed;
+	}
+
+	return 0;
 probe_setup_failed:
 	cqspi_controller_enable(cqspi, 0);
 probe_reset_failed:
@@ -1409,17 +1318,14 @@ static int cqspi_probe(struct platform_device *pdev)
 probe_clk_failed:
 	pm_runtime_put_sync(dev);
 	pm_runtime_disable(dev);
+probe_master_put:
+	spi_master_put(master);
 	return ret;
 }
 
 static int cqspi_remove(struct platform_device *pdev)
 {
 	struct cqspi_st *cqspi = platform_get_drvdata(pdev);
-	int i;
-
-	for (i = 0; i < CQSPI_MAX_CHIPSELECT; i++)
-		if (cqspi->f_pdata[i].registered)
-			mtd_device_unregister(&cqspi->f_pdata[i].nor.mtd);
 
 	cqspi_controller_enable(cqspi, 0);
 
@@ -1462,17 +1368,15 @@ static const struct dev_pm_ops cqspi__dev_pm_ops = {
 #endif
 
 static const struct cqspi_driver_platdata cdns_qspi = {
-	.hwcaps_mask = CQSPI_BASE_HWCAPS_MASK,
 	.quirks = CQSPI_DISABLE_DAC_MODE,
 };
 
 static const struct cqspi_driver_platdata k2g_qspi = {
-	.hwcaps_mask = CQSPI_BASE_HWCAPS_MASK,
 	.quirks = CQSPI_NEEDS_WR_DELAY,
 };
 
 static const struct cqspi_driver_platdata am654_ospi = {
-	.hwcaps_mask = CQSPI_BASE_HWCAPS_MASK | SNOR_HWCAPS_READ_1_1_8,
+	.hwcaps_mask = CQSPI_SUPPORTS_OCTAL,
 	.quirks = CQSPI_NEEDS_WR_DELAY,
 };
 
@@ -1511,3 +1415,5 @@ MODULE_LICENSE("GPL v2");
 MODULE_ALIAS("platform:" CQSPI_NAME);
 MODULE_AUTHOR("Ley Foon Tan <[email protected]>");
 MODULE_AUTHOR("Graham Moore <[email protected]>");
+MODULE_AUTHOR("Vadivel Murugan R <[email protected]>");
+MODULE_AUTHOR("Vignesh Raghavendra <[email protected]>");
Signature · 1 line
2.26.2
Reviewed-by on v3 7/8
#10 lore raw

Re: [PATCH v3 7/8] mtd: spi-nor: Convert cadence-quadspi to use spi-mem framework

Quoted 6 lines · EEST Vignesh Raghavendra

From: Ramuthevar Vadivel Murugan
<[email protected]>

Move cadence-quadspi driver to use spi-mem framework. This is required to make the driver support for SPI NAND flashes in future.

Quoted 8 lines

Driver is feature compliant with existing SPI NOR version.

Signed-off-by: Ramuthevar Vadivel Murugan <[email protected]> Signed-off-by: Vignesh Raghavendra <[email protected]>

---
 .../mtd/spi-nor/controllers/cadence-quadspi.c | 476 +++++++-----------
 1 file changed, 191 insertions(+), 285 deletions(-)
author maintainer
#11 lore raw

PATCH v3 8/8 spi: Move cadence-quadspi driver to drivers/spi/

In reply to Vignesh Raghavendra

From: Ramuthevar Vadivel Murugan <[email protected]>

Now that cadence-quadspi has been converted to use spi-mem framework, move it under drivers/spi/

Update license header to match SPI subsystem style

---
 drivers/mtd/spi-nor/controllers/Kconfig            | 11 -----------
 drivers/mtd/spi-nor/controllers/Makefile           |  1 -
 drivers/spi/Kconfig                                | 11 +++++++++++
 drivers/spi/Makefile                               |  1 +
 .../spi-cadence-quadspi.c}                         | 14 +++++++-------
 5 files changed, 19 insertions(+), 19 deletions(-)
 rename drivers/{mtd/spi-nor/controllers/cadence-quadspi.c => spi/spi-cadence-quadspi.c} (99%)
drivers/mtd/spi-nor/controllers/Kconfig +0 -11
index d89a5ea9446a..5c0e0ec2e6d1 100644
@@ -9,17 +9,6 @@ config SPI_ASPEED_SMC
 	  and support for the SPI flash memory controller (SPI) for
 	  the host firmware. The implementation only supports SPI NOR.
 
-config SPI_CADENCE_QUADSPI
-	tristate "Cadence Quad SPI controller"
-	depends on OF && (ARM || ARM64 || COMPILE_TEST)
-	help
-	  Enable support for the Cadence Quad SPI Flash controller.
-
-	  Cadence QSPI is a specialized controller for connecting an SPI
-	  Flash over 1/2/4-bit wide bus. Enable this option if you have a
-	  device with a Cadence QSPI controller and want to access the
-	  Flash as an MTD device.
-
 config SPI_HISI_SFC
 	tristate "Hisilicon FMC SPI NOR Flash Controller(SFC)"
 	depends on ARCH_HISI || COMPILE_TEST
drivers/mtd/spi-nor/controllers/Makefile +0 -1
index 46e6fbe586e3..e7abba491d98 100644
@@ -1,6 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
 obj-$(CONFIG_SPI_ASPEED_SMC)	+= aspeed-smc.o
-obj-$(CONFIG_SPI_CADENCE_QUADSPI)	+= cadence-quadspi.o
 obj-$(CONFIG_SPI_HISI_SFC)	+= hisi-sfc.o
 obj-$(CONFIG_SPI_NXP_SPIFI)	+= nxp-spifi.o
 obj-$(CONFIG_SPI_INTEL_SPI)	+= intel-spi.o
drivers/spi/Kconfig +11 -0
index 099d6a75a371..2de8098b26c1 100644
@@ -200,6 +200,17 @@ config SPI_CADENCE
 	  This selects the Cadence SPI controller master driver
 	  used by Xilinx Zynq and ZynqMP.
 
+config SPI_CADENCE_QUADSPI
+	tristate "Cadence Quad SPI controller"
+	depends on OF && (ARM || ARM64 || COMPILE_TEST)
+	help
+	  Enable support for the Cadence Quad SPI Flash controller.
+
+	  Cadence QSPI is a specialized controller for connecting an SPI
+	  Flash over 1/2/4-bit wide bus. Enable this option if you have a
+	  device with a Cadence QSPI controller and want to access the
+	  Flash as an MTD device.
+
 config SPI_CLPS711X
 	tristate "CLPS711X host SPI controller"
 	depends on ARCH_CLPS711X || COMPILE_TEST
drivers/spi/Makefile +1 -0
index 889368f4ad53..f03834d1d312 100644
@@ -31,6 +31,7 @@ obj-$(CONFIG_SPI_BCM_QSPI)		+= spi-iproc-qspi.o spi-brcmstb-qspi.o spi-bcm-qspi.
 obj-$(CONFIG_SPI_BITBANG)		+= spi-bitbang.o
 obj-$(CONFIG_SPI_BUTTERFLY)		+= spi-butterfly.o
 obj-$(CONFIG_SPI_CADENCE)		+= spi-cadence.o
+obj-$(CONFIG_SPI_CADENCE_QUADSPI)	+= spi-cadence-quadspi.o
 obj-$(CONFIG_SPI_CLPS711X)		+= spi-clps711x.o
 obj-$(CONFIG_SPI_COLDFIRE_QSPI)		+= spi-coldfire-qspi.o
 obj-$(CONFIG_SPI_DAVINCI)		+= spi-davinci.o
drivers/spi/spi-cadence-quadspi.c renamed from drivers/mtd/spi-nor/controllers/cadence-quadspi.c +7 -7
similarity index 99%
rename from drivers/mtd/spi-nor/controllers/cadence-quadspi.c
rename to drivers/spi/spi-cadence-quadspi.c
index c12a1c0191b9..1c1a9d17eec0 100644
@@ -1,11 +1,11 @@
 // SPDX-License-Identifier: GPL-2.0-only
-/*
- * Driver for Cadence QSPI Controller
- *
- * Copyright Altera Corporation (C) 2012-2014. All rights reserved.
- * Copyright Intel Corporation (C) 2019-2020. All rights reserved.
- * Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com
- */
+//
+// Driver for Cadence QSPI Controller
+//
+// Copyright Altera Corporation (C) 2012-2014. All rights reserved.
+// Copyright Intel Corporation (C) 2019-2020. All rights reserved.
+// Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com
+
 #include <linux/clk.h>
 #include <linux/completion.h>
 #include <linux/delay.h>
Signature · 1 line
2.26.2
Reviewed-by on v3 8/8
#12 lore raw

Re: [PATCH v3 8/8] spi: Move cadence-quadspi driver to drivers/spi/

Hi, Mark,

Quoted 19 lines · EEST Vignesh Raghavendra

From: Ramuthevar Vadivel Murugan
<[email protected]>

Now that cadence-quadspi has been converted to use spi-mem framework, move it under drivers/spi/

Update license header to match SPI subsystem style

Signed-off-by: Ramuthevar Vadivel Murugan <[email protected]> Signed-off-by: Vignesh Raghavendra <[email protected]>

---
 drivers/mtd/spi-nor/controllers/Kconfig            | 11 -----------
 drivers/mtd/spi-nor/controllers/Makefile           |  1 -
 drivers/spi/Kconfig                                | 11 +++++++++++
 drivers/spi/Makefile                               |  1 +
 .../spi-cadence-quadspi.c}                         | 14 +++++++-------
 5 files changed, 19 insertions(+), 19 deletions(-)
 rename drivers/{mtd/spi-nor/controllers/cadence-quadspi.c =>
Quoted 1 line

spi/spi-cadence-quadspi.c} (99%)

If this patch set looks good to you, would you take it through the SPI tree? If so, I would need an immutable tag, so I can merge back in spi-nor/next in order to fix a small conflict that will appear in drivers/mtd/spi-nor/ controllers/Kconfig. Vignesh would have to respin this patch on top of v5.7- rc1. With this addressed:

author maintainer
#13 lore raw

Re: [PATCH v3 8/8] spi: Move cadence-quadspi driver to drivers/spi/

Quoted 24 lines · On 01/06/20 12:30 pm, [email protected] wrote:

Hi, Mark,

Quoted 19 lines · EEST Vignesh Raghavendra

From: Ramuthevar Vadivel Murugan
<[email protected]>

Now that cadence-quadspi has been converted to use spi-mem framework, move it under drivers/spi/

Update license header to match SPI subsystem style

Signed-off-by: Ramuthevar Vadivel Murugan <[email protected]> Signed-off-by: Vignesh Raghavendra <[email protected]>

---
 drivers/mtd/spi-nor/controllers/Kconfig            | 11 -----------
 drivers/mtd/spi-nor/controllers/Makefile           |  1 -
 drivers/spi/Kconfig                                | 11 +++++++++++
 drivers/spi/Makefile                               |  1 +
 .../spi-cadence-quadspi.c}                         | 14 +++++++-------
 5 files changed, 19 insertions(+), 19 deletions(-)
 rename drivers/{mtd/spi-nor/controllers/cadence-quadspi.c =>
Quoted 1 line

spi/spi-cadence-quadspi.c} (99%)

Quoted 8 lines

If this patch set looks good to you, would you take it through the SPI tree? If so, I would need an immutable tag, so I can merge back in spi-nor/next in order to fix a small conflict that will appear in drivers/mtd/spi-nor/ controllers/Kconfig. Vignesh would have to respin this patch on top of v5.7- rc1. With this addressed:

I have resent v3 on top of v5.7-rc1 (also applies cleanly on spi tree's for-next branch):

https://lore.kernel.org/linux-spi/[email protected]/T/#t