lan743x: Added fixed link and RGMII support
Subsystems (3)
PATCH 1/1 lan743x: Added fixed link and RGMII support
Microchip lan7431 is frequently connected to a phy. However, it can also be directly connected to a MII remote peer without any phy in between. For supporting such a phyless hardware setup in Linux we utilized phylib, which supports a fixed-link configuration via the device tree. And we added support for defining the connection type R/GMII in the device tree.
New behavior:
-------------
. The automatic speed and duplex detection of the lan743x silicon
between mac and phy is disabled. Instead phylib is used like in other typical Linux drivers. The usage of phylib allows to specify fixed-link parameters in the device tree.
. The device tree entry phy-connection-type is supported now with
the modes RGMII or (G)MII (default).
Development state:
------------------
. Tested with fixed-phy configurations. Not yet tested in normal
configurations with phy. Microchip kindly offered testing as soon as the Corona measures allow this.
. All review findings of Andrew Lunn are included
Example:
--------
&pcie {
status = "okay";
host@0 {
reg = <0 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
ethernet@0 {
compatible = "weyland-yutani,noscom1", "microchip,lan743x";
status = "okay";
reg = <0 0 0 0 0>;
phy-connection-type = "rgmii";
fixed-link {
speed = <100>;
full-duplex;
};
};
};
};--- .../net/ethernet/microchip/lan743x_ethtool.c | 4 +- drivers/net/ethernet/microchip/lan743x_main.c | 81 ++++++++++++++++--- drivers/net/ethernet/microchip/lan743x_main.h | 6 ++ drivers/net/ethernet/microchip/lan743x_ptp.c | 2 +- 4 files changed, 80 insertions(+), 13 deletions(-)
drivers/net/ethernet/microchip/lan743x_ethtool.c +2 -2
@@ -2,11 +2,11 @@/* Copyright (C) 2018 Microchip Technology Inc. */ #include <linux/netdevice.h> -#include "lan743x_main.h" -#include "lan743x_ethtool.h" #include <linux/net_tstamp.h> #include <linux/pci.h> #include <linux/phy.h> +#include "lan743x_main.h" +#include "lan743x_ethtool.h" /* eeprom */ #define LAN743X_EEPROM_MAGIC (0x74A5)
drivers/net/ethernet/microchip/lan743x_main.c +71 -10
119 lines not on this page · raw message
drivers/net/ethernet/microchip/lan743x_main.h +6 -0
@@ -4,6 +4,7 @@#ifndef _LAN743X_H#define _LAN743X_H +#include <linux/phy.h> #include "lan743x_ptp.h" #define DRIVER_AUTHOR "Bryan Whitehead <[email protected]>"
@@ -104,10 +105,14 @@ ((value << 0) & FCT_FLOW_CTL_ON_THRESHOLD_)#define MAC_CR (0x100) +#define MAC_CR_MII_EN_ BIT(19)#define MAC_CR_EEE_EN_ BIT(17)#define MAC_CR_ADD_ BIT(12)#define MAC_CR_ASD_ BIT(11)#define MAC_CR_CNTR_RST_ BIT(5) +#define MAC_CR_DPX_ BIT(3) +#define MAC_CR_CFG_H_ BIT(2) +#define MAC_CR_CFG_L_ BIT(1)#define MAC_CR_RST_ BIT(0)#define MAC_RX (0x104)
@@ -698,6 +703,7 @@ struct lan743x_rx {struct lan743x_adapter {struct net_device *netdev;struct mii_bus *mdiobus; +phy_interface_t phy_mode;int msg_enable;#ifdef CONFIG_PM u32 wolopts;
drivers/net/ethernet/microchip/lan743x_ptp.c +1 -1
@@ -2,12 +2,12 @@/* Copyright (C) 2018 Microchip Technology Inc. */ #include <linux/netdevice.h> -#include "lan743x_main.h" #include <linux/ptp_clock_kernel.h> #include <linux/module.h> #include <linux/pci.h> #include <linux/net_tstamp.h> +#include "lan743x_main.h" #include "lan743x_ptp.h"
Signature · 1 line
2.25.1
Quoted 50 lines · Roelof Berg
Microchip lan7431 is frequently connected to a phy. However, it can also be directly connected to a MII remote peer without any phy in between. For supporting such a phyless hardware setup in Linux we utilized phylib, which supports a fixed-link configuration via the device tree. And we added support for defining the connection type R/GMII in the device tree.
New behavior:
-------------
. The automatic speed and duplex detection of the lan743x silicon
between mac and phy is disabled. Instead phylib is used like in other typical Linux drivers. The usage of phylib allows to specify fixed-link parameters in the device tree.. The device tree entry phy-connection-type is supported now with
the modes RGMII or (G)MII (default).Development state:
------------------
. Tested with fixed-phy configurations. Not yet tested in normal
configurations with phy. Microchip kindly offered testing as soon as the Corona measures allow this.. All review findings of Andrew Lunn are included
Example:
--------&pcie { status = "okay"; host@0 { reg = <0 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; ethernet@0 { compatible = "weyland-yutani,noscom1", "microchip,lan743x"; status = "okay"; reg = <0 0 0 0 0>; phy-connection-type = "rgmii"; fixed-link { speed = <100>; full-duplex; }; }; }; };
Quoted 1 line
Signed-off-by Roelof Berg <[email protected]>
Hi Roelof
It looks like you took my suggestion as a basis. So i should give you:
since i did not include one in my posting. I'm happy to see it helped, and fixed some other issues you were seeing.
Andrew
From: Roelof Berg <[email protected]>
Date: Fri, 29 May 2020 21:30:02 +0200
Quoted 6 lines
Microchip lan7431 is frequently connected to a phy. However, it can also be directly connected to a MII remote peer without any phy in between. For supporting such a phyless hardware setup in Linux we utilized phylib, which supports a fixed-link configuration via the device tree. And we added support for defining the connection type R/GMII in the device tree.
...
Applied, thank you.
Re: [PATCH] lan743x: Added fixed link and RGMII support / BROKEN PATCH
TEST REPORT: BROKEN PATCH
Thanks to everyone for working on the fixed link feature of lan743x eth driver.
I received more test hardware today, and one piece of hardware (EVBlan7430) becomes incompatible by the patch. We need to roll back for now. Sorry.
I’ll discuss about options of how to proceed in a second e-mail.
Thank you and best regards,
Roelof
Quoted 12 lines
David Miller <[email protected]>:
Quoted 6 lines
Microchip lan7431 is frequently connected to a phy. However, it can also be directly connected to a MII remote peer without any phy in between. For supporting such a phyless hardware setup in Linux we utilized phylib, which supports a fixed-link configuration via the device tree. And we added support for defining the connection type R/GMII in the device tree.
...
Applied, thank you.
Re: [PATCH] lan743x: Added fixed link and RGMII support / BROKEN PATCH
Quoted 8 lines · Roelof Berg
TEST REPORT: BROKEN PATCH
Thanks to everyone for working on the fixed link feature of lan743x eth driver.
I received more test hardware today, and one piece of hardware (EVBlan7430) becomes incompatible by the patch. We need to roll back for now. Sorry.
Hi Roelof
We have a bit of time to fix this, before it becomes too critical. So lets try to fix it.
How did it break?
Thanks
Andrew
Re: [PATCH] lan743x: Added fixed link and RGMII support / debugging
Ok, let's proceed :) The code runs well, dmesg looks good, ip addr shows me a link up, speed/duplex looks ok. But it does not transfer any data.
Debugging steps (A/B versions):
- Check clocks with oscilloscope (10/100/1000)
- Dump actual register settings
- Trace Phy-Phy autonegotiation and ensure that our patch catches up the result
Research topic:
I will also look if in my test hardware uses distinct MDIO traces or in-band MDIO (MDIO via MII). Would inband MDIO need the autosense feature to talk to the phy before phy-phy auto negotiation is complete ? E.g. for triggering phy-phy autoneg ? And is this (inband mdio) maybe the reason why the may-phy autosense feature exists in the silicon ?
Thanks,
Roelof
Quoted 22 lines
Am 03.06.2020 um 17:59 schrieb Andrew Lunn <[email protected]>:
Quoted 8 lines · Roelof Berg
TEST REPORT: BROKEN PATCH
Thanks to everyone for working on the fixed link feature of lan743x eth driver.
I received more test hardware today, and one piece of hardware (EVBlan7430) becomes incompatible by the patch. We need to roll back for now. Sorry.
Hi Roelof
We have a bit of time to fix this, before it becomes too critical. So lets try to fix it.
How did it break?
Thanks
Andrew
Re: [PATCH] lan743x: Added fixed link and RGMII support / debugging
Quoted 6 lines · Roelof Berg
Ok, let's proceed :) The code runs well, dmesg looks good, ip addr shows me a link up, speed/duplex looks ok. But it does not transfer any data.
Debugging steps (A/B versions):
- Check clocks with oscilloscope (10/100/1000)
- Dump actual register settings
- Trace Phy-Phy autonegotiation and ensure that our patch catches up the result
Adding #define DEBUG to the top of drivers/net/phy/phy.c will get you some debug info.
What PHY is being used?
Is it using RGMII?
If it looks like the PHY and the MAC are happy, just that frames are not being transferred between them, it could be RGMII delays.
Andrew
Re: [PATCH] lan743x: Added fixed link and RGMII support / debugging
I’m testing with Microchip Lan7430, which is an integrated circuit that contains MAC and PHY in one package. With the release kernel the hardware works fine, so the overall configuration is ok (jumpers).
I will verify wether the effective RGMII and delay settings, you mention, are equal in both driver versions.
Quoted 9 lines
Quoted 1 line
Ok, let's proceed :)
What PHY is being used?
Is it using RGMII?If it looks like the PHY and the MAC are happy, just that frames are not being transferred between them, it could be RGMII delays.
Andrew
Re: [PATCH] lan743x: Added fixed link and RGMII support / debugging
In reply to Andrew LunnThanks, I found the cause, the delta patch is submitted. Lan7430 runs now in different speeds, also ‚hot swap‘ between different speeds works well. Normal mode and fixed-phy mode coexist properly.
So, I guess we’re done :) However, I’ll spend some more time testing to ensure we’re really safe.
(I’m sending this e-mail through a Microchip Lan7430 by the way :)
Roelof Berg
Quoted 8 lines
Adding #define DEBUG to the top of
drivers/net/phy/phy.cwill get you some debug info.[…]
Andrew
Re: [PATCH] lan743x: Added fixed link and RGMII support / debugging
In reply to Andrew LunnIf I find a fix, would I need to submit a delta patch (to our last one) or a full patch ?
Thanks.
Quoted 5 lines
So lets try to fix it.
Thanks
Andrew
Re: [PATCH] lan743x: Added fixed link and RGMII support / debugging
Quoted 1 line · Roelof Berg
If I find a fix, would I need to submit a delta patch (to our last one) or a full patch ?
A delta.
Andrew
A message that is not in the archive (sent off-list or not yet received): [email protected]
Re: [PATCH] lan743x: Added fixed link and RGMII support / Options for proceeding ?
Hi,
we need to decide how to continue with the lan743x patch for fixed phy support. Thanks everyone for the valuable time.
Summary of the development steps so far:
The patch initially had low influence on the installed base, but lacked some compatibility to Linux best practices. During the review process we found improvement potential. We decided to make the patch more similar to the majority of Linux drivers, by avoiding a special autodetection silicon feature that is unique. However, now, with more test hardware available, this road becomes more difficult than we initially assumed.
Would it be ok to split the topics into two distinct patches ?
Topic a: New feature: Add fixed link and RGMII support in a minimal invasive way. (Including fixing a reboot-issue that the last patch fixed.)
Topic b: Refactor old driver: Understand, and if possible remove, the silicon’s Mac-Phy auto-negotiation feature.
Maybe splitting distinct features into distinct patches is the most defensive approach, now that device testing disconfirmed our promising approach ?
Thanks everyone for cooperating on this feature,
Roelof
Quoted 10 lines
Roelof Berg <[email protected]>:
Testing note [...]
- Different from prior approaches it affects the installed base. So we need some more testing (with hardware I don’t have available yet) and I’m in contact with Microchip already.Thanks for guiding us to a proper solution,
Roelof BergQuoted 2 lines
. The automatic speed and duplex detection of the lan743x silicon between mac and phy is disabled.