Skip to contentSkip to conversation

pinctrl-single: fix pcs_parse_pinconf() return value

PATCH In review Drew Fustini 4 participants 6 messages Jun 8, 2020 – Jul 5, 2020

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 pinctrl-single: fix pcs_parse_pinconf() return value

This patch causes pcs_parse_pinconf() to return -ENOTSUPP when no pinctrl_map is added. The current behavior is to return 0 when !PCS_HAS_PINCONF or !nconfs. Thus pcs_parse_one_pinctrl_entry() incorrectly assumes that a map was added and sets num_maps = 2.

Analysis:
=========
The function pcs_parse_one_pinctrl_entry() calls pcs_parse_pinconf() if PCS_HAS_PINCONF is enabled. The function pcs_parse_pinconf() returns 0 to indicate there was no error and num_maps is then set to 2:

980 static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs,

 981                                                 struct device_node *np,
 982                                                 struct pinctrl_map **map,
 983                                                 unsigned *num_maps,
 984                                                 const char **pgnames)
 985 {
<snip>
1053         (*map)->type = PIN_MAP_TYPE_MUX_GROUP;
1054         (*map)->data.mux.group = np->name;
1055         (*map)->data.mux.function = np->name;

1056
1057 if (PCS_HAS_PINCONF && function) {
1058 res = pcs_parse_pinconf(pcs, np, function, map);
1059 if (res)
1060 goto free_pingroups;
1061 *num_maps = 2;
1062 } else {
1063 *num_maps = 1;
1064 }

However, pcs_parse_pinconf() will also return 0 if !PCS_HAS_PINCONF or !nconfs. I believe these conditions should indicate that no map was added by returning -ENOTSUPP. Otherwise pcs_parse_one_pinctrl_entry() will set num_maps = 2 even though no maps were successfully added, as it does not reach "m++" on line 940:

895 static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np,
896 struct pcs_function *func,
897 struct pinctrl_map **map)
898
899 {
900 struct pinctrl_map *m = *map;
<snip>
917 /* If pinconf isn't supported, don't parse properties in below. */
918 if (!PCS_HAS_PINCONF)
919 return 0;
920
921 /* cacluate how much properties are supported in current node */
922 for (i = 0; i < ARRAY_SIZE(prop2); i++) {
923 if (of_find_property(np, prop2[i].name, NULL))
924 nconfs++;
925 }
926 for (i = 0; i < ARRAY_SIZE(prop4); i++) {
927 if (of_find_property(np, prop4[i].name, NULL))
928 nconfs++;
929 }
930 if (!nconfs)
919 return 0;
932
933 func->conf = devm_kcalloc(pcs->dev,
934 nconfs, sizeof(struct pcs_conf_vals),
935 GFP_KERNEL);
936 if (!func->conf)
937 return -ENOMEM;

 938         func->nconfs = nconfs;
 939         conf = &(func->conf[0]);
 940         m++;

This situtation will cause a boot failure [0] on the BeagleBone Black (AM3358) when am33xx_pinmux node in arch/arm/boot/dts/am33xx-l4.dtsi has compatible = "pinconf-single" instead of "pinctrl-single".

The patch fixes this issue by returning -ENOSUPP when !PCS_HAS_PINCONF or !nconfs, so that pcs_parse_one_pinctrl_entry() will know that no map was added.

Logic is also added to pcs_parse_one_pinctrl_entry() to distinguish between -ENOSUPP and other errors. In the case of -ENOSUPP, num_maps is set to 1 as it is valid for pinconf to be enabled and a given pin group to not any pinconf properties.

[0] https://lore.kernel.org/linux-omap/20200529175544.GA3766151@x1/

Fixes 9dddb4df90d1 ("pinctrl: single: support generic pinconf")

---
changes from V1 [0]:
- if pcs_parse_pinconf() returns -ENOSUPP, then set num_maps to 1 and proceed normally as it is valid for group to have no pinconf props
- added Fixes: tag thanks to Gustavo A. R. Silva

[0] https://lore.kernel.org/linux-omap/20200531204147.GA664833@x1/

 drivers/pinctrl/pinctrl-single.c | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)
drivers/pinctrl/pinctrl-single.c +7 -4
index 1e0614daee9b..a9d511982780 100644
@@ -916,7 +916,7 @@ static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np,
 
 	/* If pinconf isn't supported, don't parse properties in below. */
 	if (!PCS_HAS_PINCONF)
-		return 0;
+		return -ENOTSUPP;
 
 	/* cacluate how much properties are supported in current node */
 	for (i = 0; i < ARRAY_SIZE(prop2); i++) {
@@ -928,7 +928,7 @@ static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np,
 			nconfs++;
 	}
 	if (!nconfs)
-		return 0;
+		return -ENOTSUPP;
 
 	func->conf = devm_kcalloc(pcs->dev,
 				  nconfs, sizeof(struct pcs_conf_vals),
@@ -1056,9 +1056,12 @@ static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs,
 
 	if (PCS_HAS_PINCONF && function) {
 		res = pcs_parse_pinconf(pcs, np, function, map);
-		if (res)
+		if (res == 0)
+			*num_maps = 2;
+		else if (res == -ENOTSUPP)
+			*num_maps = 1;
+		else
 			goto free_pingroups;
-		*num_maps = 2;
 	} else {
 		*num_maps = 1;
 	}
Signature · 1 line
2.25.1
maintainer Acked-by on v2 1/1
#1 lore raw
Quoted 4 lines · Drew Fustini

This patch causes pcs_parse_pinconf() to return -ENOTSUPP when no pinctrl_map is added. The current behavior is to return 0 when !PCS_HAS_PINCONF or !nconfs. Thus pcs_parse_one_pinctrl_entry() incorrectly assumes that a map was added and sets num_maps = 2.

...

Quoted 1 line
Fixes 9dddb4df90d1 ("pinctrl: single: support generic pinconf")

It would be good to get an ack/tested-by from Haojian for this.

The patch looks right to me:

#2 lore raw
In reply to Drew Fustini
Quoted 82 lines · Drew Fustini

This patch causes pcs_parse_pinconf() to return -ENOTSUPP when no pinctrl_map is added. The current behavior is to return 0 when !PCS_HAS_PINCONF or !nconfs. Thus pcs_parse_one_pinctrl_entry() incorrectly assumes that a map was added and sets num_maps = 2.

Analysis:
=========
The function pcs_parse_one_pinctrl_entry() calls pcs_parse_pinconf() if PCS_HAS_PINCONF is enabled. The function pcs_parse_pinconf() returns 0 to indicate there was no error and num_maps is then set to 2:

980 static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs,

 981                                                 struct device_node *np,
 982                                                 struct pinctrl_map **map,
 983                                                 unsigned *num_maps,
 984                                                 const char **pgnames)
 985 {
<snip>
1053         (*map)->type = PIN_MAP_TYPE_MUX_GROUP;
1054         (*map)->data.mux.group = np->name;
1055         (*map)->data.mux.function = np->name;

1056
1057 if (PCS_HAS_PINCONF && function) {
1058 res = pcs_parse_pinconf(pcs, np, function, map);
1059 if (res)
1060 goto free_pingroups;
1061 *num_maps = 2;
1062 } else {
1063 *num_maps = 1;
1064 }

However, pcs_parse_pinconf() will also return 0 if !PCS_HAS_PINCONF or !nconfs. I believe these conditions should indicate that no map was added by returning -ENOTSUPP. Otherwise pcs_parse_one_pinctrl_entry() will set num_maps = 2 even though no maps were successfully added, as it does not reach "m++" on line 940:

895 static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np,
896 struct pcs_function *func,
897 struct pinctrl_map **map)
898
899 {
900 struct pinctrl_map *m = *map;
<snip>
917 /* If pinconf isn't supported, don't parse properties in below. */
918 if (!PCS_HAS_PINCONF)
919 return 0;
920
921 /* cacluate how much properties are supported in current node */
922 for (i = 0; i < ARRAY_SIZE(prop2); i++) {
923 if (of_find_property(np, prop2[i].name, NULL))
924 nconfs++;
925 }
926 for (i = 0; i < ARRAY_SIZE(prop4); i++) {
927 if (of_find_property(np, prop4[i].name, NULL))
928 nconfs++;
929 }
930 if (!nconfs)
919 return 0;
932
933 func->conf = devm_kcalloc(pcs->dev,
934 nconfs, sizeof(struct pcs_conf_vals),
935 GFP_KERNEL);
936 if (!func->conf)
937 return -ENOMEM;

 938         func->nconfs = nconfs;
 939         conf = &(func->conf[0]);
 940         m++;

This situtation will cause a boot failure [0] on the BeagleBone Black (AM3358) when am33xx_pinmux node in arch/arm/boot/dts/am33xx-l4.dtsi has compatible = "pinconf-single" instead of "pinctrl-single".

The patch fixes this issue by returning -ENOSUPP when !PCS_HAS_PINCONF or !nconfs, so that pcs_parse_one_pinctrl_entry() will know that no map was added.

Logic is also added to pcs_parse_one_pinctrl_entry() to distinguish between -ENOSUPP and other errors. In the case of -ENOSUPP, num_maps is set to 1 as it is valid for pinconf to be enabled and a given pin group to not any pinconf properties.

Quoted 4 lines

[0] https://lore.kernel.org/linux-omap/20200529175544.GA3766151@x1/

Fixes 9dddb4df90d1 ("pinctrl: single: support generic pinconf")

Patch applied as non-critical (for-next) fix.

If there is no hurry let's merge it this way with lots of testing along the way.

Yours,
Linus Walleij

#3 lore raw
Quoted 89 lines · Linus Walleij
Quoted 82 lines · Drew Fustini

This patch causes pcs_parse_pinconf() to return -ENOTSUPP when no pinctrl_map is added. The current behavior is to return 0 when !PCS_HAS_PINCONF or !nconfs. Thus pcs_parse_one_pinctrl_entry() incorrectly assumes that a map was added and sets num_maps = 2.

Analysis:
=========
The function pcs_parse_one_pinctrl_entry() calls pcs_parse_pinconf() if PCS_HAS_PINCONF is enabled. The function pcs_parse_pinconf() returns 0 to indicate there was no error and num_maps is then set to 2:

980 static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs,

 981                                                 struct device_node *np,
 982                                                 struct pinctrl_map **map,
 983                                                 unsigned *num_maps,
 984                                                 const char **pgnames)
 985 {
<snip>
1053         (*map)->type = PIN_MAP_TYPE_MUX_GROUP;
1054         (*map)->data.mux.group = np->name;
1055         (*map)->data.mux.function = np->name;

1056
1057 if (PCS_HAS_PINCONF && function) {
1058 res = pcs_parse_pinconf(pcs, np, function, map);
1059 if (res)
1060 goto free_pingroups;
1061 *num_maps = 2;
1062 } else {
1063 *num_maps = 1;
1064 }

However, pcs_parse_pinconf() will also return 0 if !PCS_HAS_PINCONF or !nconfs. I believe these conditions should indicate that no map was added by returning -ENOTSUPP. Otherwise pcs_parse_one_pinctrl_entry() will set num_maps = 2 even though no maps were successfully added, as it does not reach "m++" on line 940:

895 static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np,
896 struct pcs_function *func,
897 struct pinctrl_map **map)
898
899 {
900 struct pinctrl_map *m = *map;
<snip>
917 /* If pinconf isn't supported, don't parse properties in below. */
918 if (!PCS_HAS_PINCONF)
919 return 0;
920
921 /* cacluate how much properties are supported in current node */
922 for (i = 0; i < ARRAY_SIZE(prop2); i++) {
923 if (of_find_property(np, prop2[i].name, NULL))
924 nconfs++;
925 }
926 for (i = 0; i < ARRAY_SIZE(prop4); i++) {
927 if (of_find_property(np, prop4[i].name, NULL))
928 nconfs++;
929 }
930 if (!nconfs)
919 return 0;
932
933 func->conf = devm_kcalloc(pcs->dev,
934 nconfs, sizeof(struct pcs_conf_vals),
935 GFP_KERNEL);
936 if (!func->conf)
937 return -ENOMEM;

 938         func->nconfs = nconfs;
 939         conf = &(func->conf[0]);
 940         m++;

This situtation will cause a boot failure [0] on the BeagleBone Black (AM3358) when am33xx_pinmux node in arch/arm/boot/dts/am33xx-l4.dtsi has compatible = "pinconf-single" instead of "pinctrl-single".

The patch fixes this issue by returning -ENOSUPP when !PCS_HAS_PINCONF or !nconfs, so that pcs_parse_one_pinctrl_entry() will know that no map was added.

Logic is also added to pcs_parse_one_pinctrl_entry() to distinguish between -ENOSUPP and other errors. In the case of -ENOSUPP, num_maps is set to 1 as it is valid for pinconf to be enabled and a given pin group to not any pinconf properties.

Quoted 4 lines

[0] https://lore.kernel.org/linux-omap/20200529175544.GA3766151@x1/

Fixes 9dddb4df90d1 ("pinctrl: single: support generic pinconf")
Quoted 7 lines

Patch applied as non-critical (for-next) fix.

If there is no hurry let's merge it this way with lots of testing along the way.

Yours,
Linus Walleij

Thanks, I agree more testing is a good idea.

In particular, do you have a way to followup with Haojian Zhuang within Linaro?

Haojian added the generic pinconf support back in 2013, so it would be good to get his review.

Also, neither Tony or I have the Hikey hardware to test.

The most important to test would be those which include a .dtsi with "pinconf-single" compatible. I do plan to add pinconf-single to the AM3358 BeagleBone (which is what I am testing on), but the current mainline users are:

arch/arm/boot/dts/hi3620.dtsi
|- arch/arm/boot/dts/hi3620-hi4511.dts

arch/arm/boot/dts/pxa3xx.dtsi
|- arch/arm/boot/dts/pxa300-raumfeld-common.dtsi
|- arch/arm/boot/dts/pxa300-raumfeld-connector.dts
arch/arm/boot/dts/pxa300-raumfeld-controller.dts arch/arm/boot/dts/pxa300-raumfeld-speaker-l.dts arch/arm/boot/dts/pxa300-raumfeld-speaker-m.dts arch/arm/boot/dts/pxa300-raumfeld-speaker-one.dts arch/arm/boot/dts/pxa300-raumfeld-speaker-s.dts

I am cc'ing Daniel Mack and Robert Jarzmi as they are listed as maintainers for the pxa300 related dts files.

Those platforms using compatible = "pinctrl-single" should not be effected by this patch:

arch/arm/boot/dts/am33xx-l4.dtsi (I have changed to pinconf for test) arch/arm/boot/dts/da850.dtsi
arch/arm/boot/dts/dm814x.dtsi arch/arm/boot/dts/dm816x.dtsi arch/arm/boot/dts/hi3620.dtsi arch/arm/boot/dts/keystone-k2g.dtsi arch/arm/boot/dts/keystone-k2l.dtsi arch/arm/boot/dts/omap3-gta04.dtsi

Thanks,
Drew

#4 lore raw
Quoted 95 lines · Drew Fustini
Quoted 94 lines · Linus Walleij
Quoted 82 lines · Drew Fustini

This patch causes pcs_parse_pinconf() to return -ENOTSUPP when no pinctrl_map is added. The current behavior is to return 0 when !PCS_HAS_PINCONF or !nconfs. Thus pcs_parse_one_pinctrl_entry() incorrectly assumes that a map was added and sets num_maps = 2.

Analysis:
=========
The function pcs_parse_one_pinctrl_entry() calls pcs_parse_pinconf() if PCS_HAS_PINCONF is enabled. The function pcs_parse_pinconf() returns 0 to indicate there was no error and num_maps is then set to 2:

980 static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs,

 981                                                 struct device_node *np,
 982                                                 struct pinctrl_map **map,
 983                                                 unsigned *num_maps,
 984                                                 const char **pgnames)
 985 {
<snip>
1053         (*map)->type = PIN_MAP_TYPE_MUX_GROUP;
1054         (*map)->data.mux.group = np->name;
1055         (*map)->data.mux.function = np->name;

1056
1057 if (PCS_HAS_PINCONF && function) {
1058 res = pcs_parse_pinconf(pcs, np, function, map);
1059 if (res)
1060 goto free_pingroups;
1061 *num_maps = 2;
1062 } else {
1063 *num_maps = 1;
1064 }

However, pcs_parse_pinconf() will also return 0 if !PCS_HAS_PINCONF or !nconfs. I believe these conditions should indicate that no map was added by returning -ENOTSUPP. Otherwise pcs_parse_one_pinctrl_entry() will set num_maps = 2 even though no maps were successfully added, as it does not reach "m++" on line 940:

895 static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np,
896 struct pcs_function *func,
897 struct pinctrl_map **map)
898
899 {
900 struct pinctrl_map *m = *map;
<snip>
917 /* If pinconf isn't supported, don't parse properties in below. */
918 if (!PCS_HAS_PINCONF)
919 return 0;
920
921 /* cacluate how much properties are supported in current node */
922 for (i = 0; i < ARRAY_SIZE(prop2); i++) {
923 if (of_find_property(np, prop2[i].name, NULL))
924 nconfs++;
925 }
926 for (i = 0; i < ARRAY_SIZE(prop4); i++) {
927 if (of_find_property(np, prop4[i].name, NULL))
928 nconfs++;
929 }
930 if (!nconfs)
919 return 0;
932
933 func->conf = devm_kcalloc(pcs->dev,
934 nconfs, sizeof(struct pcs_conf_vals),
935 GFP_KERNEL);
936 if (!func->conf)
937 return -ENOMEM;

 938         func->nconfs = nconfs;
 939         conf = &(func->conf[0]);
 940         m++;

This situtation will cause a boot failure [0] on the BeagleBone Black (AM3358) when am33xx_pinmux node in arch/arm/boot/dts/am33xx-l4.dtsi has compatible = "pinconf-single" instead of "pinctrl-single".

The patch fixes this issue by returning -ENOSUPP when !PCS_HAS_PINCONF or !nconfs, so that pcs_parse_one_pinctrl_entry() will know that no map was added.

Logic is also added to pcs_parse_one_pinctrl_entry() to distinguish between -ENOSUPP and other errors. In the case of -ENOSUPP, num_maps is set to 1 as it is valid for pinconf to be enabled and a given pin group to not any pinconf properties.

Quoted 4 lines

[0] https://lore.kernel.org/linux-omap/20200529175544.GA3766151@x1/

Fixes 9dddb4df90d1 ("pinctrl: single: support generic pinconf")

Patch applied as non-critical (for-next) fix.

If there is no hurry let's merge it this way with lots of testing along the way.

Quoted 8 lines
Quoted 2 lines

Yours,
Linus Walleij

Thanks, I agree more testing is a good idea.

In particular, do you have a way to followup with Haojian Zhuang within Linaro?

Linus - do you have a way to contact Haojian Zhuan?

I found them on Freenode but they have been idle since beginning of June. Last email I can find on the mailing list is from March.

Tony and I would both like someone familiar with Hisilicon to comment on this patch as it is using pinctrl-single.

Thanks,
Drew

maintainer Tested-by on v2 1/1
#5 lore raw
In reply to Drew Fustini
Quoted 136 lines · Drew Fustini

This patch causes pcs_parse_pinconf() to return -ENOTSUPP when no pinctrl_map is added. The current behavior is to return 0 when !PCS_HAS_PINCONF or !nconfs. Thus pcs_parse_one_pinctrl_entry() incorrectly assumes that a map was added and sets num_maps = 2.

Analysis:
=========
The function pcs_parse_one_pinctrl_entry() calls pcs_parse_pinconf() if PCS_HAS_PINCONF is enabled. The function pcs_parse_pinconf() returns 0 to indicate there was no error and num_maps is then set to 2:

980 static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs,

 981                                                 struct device_node *np,
 982                                                 struct pinctrl_map **map,
 983                                                 unsigned *num_maps,
 984                                                 const char **pgnames)
 985 {
<snip>
1053         (*map)->type = PIN_MAP_TYPE_MUX_GROUP;
1054         (*map)->data.mux.group = np->name;
1055         (*map)->data.mux.function = np->name;

1056
1057 if (PCS_HAS_PINCONF && function) {
1058 res = pcs_parse_pinconf(pcs, np, function, map);
1059 if (res)
1060 goto free_pingroups;
1061 *num_maps = 2;
1062 } else {
1063 *num_maps = 1;
1064 }

However, pcs_parse_pinconf() will also return 0 if !PCS_HAS_PINCONF or !nconfs. I believe these conditions should indicate that no map was added by returning -ENOTSUPP. Otherwise pcs_parse_one_pinctrl_entry() will set num_maps = 2 even though no maps were successfully added, as it does not reach "m++" on line 940:

895 static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np,
896 struct pcs_function *func,
897 struct pinctrl_map **map)
898
899 {
900 struct pinctrl_map *m = *map;
<snip>
917 /* If pinconf isn't supported, don't parse properties in below. */
918 if (!PCS_HAS_PINCONF)
919 return 0;
920
921 /* cacluate how much properties are supported in current node */
922 for (i = 0; i < ARRAY_SIZE(prop2); i++) {
923 if (of_find_property(np, prop2[i].name, NULL))
924 nconfs++;
925 }
926 for (i = 0; i < ARRAY_SIZE(prop4); i++) {
927 if (of_find_property(np, prop4[i].name, NULL))
928 nconfs++;
929 }
930 if (!nconfs)
919 return 0;
932
933 func->conf = devm_kcalloc(pcs->dev,
934 nconfs, sizeof(struct pcs_conf_vals),
935 GFP_KERNEL);
936 if (!func->conf)
937 return -ENOMEM;

 938         func->nconfs = nconfs;
 939         conf = &(func->conf[0]);
 940         m++;

This situtation will cause a boot failure [0] on the BeagleBone Black (AM3358) when am33xx_pinmux node in arch/arm/boot/dts/am33xx-l4.dtsi has compatible = "pinconf-single" instead of "pinctrl-single".

The patch fixes this issue by returning -ENOSUPP when !PCS_HAS_PINCONF or !nconfs, so that pcs_parse_one_pinctrl_entry() will know that no map was added.

Logic is also added to pcs_parse_one_pinctrl_entry() to distinguish between -ENOSUPP and other errors. In the case of -ENOSUPP, num_maps is set to 1 as it is valid for pinconf to be enabled and a given pin group to not any pinconf properties.

[0] https://lore.kernel.org/linux-omap/20200529175544.GA3766151@x1/

Fixes 9dddb4df90d1 ("pinctrl: single: support generic pinconf")

---
changes from V1 [0]:
- if pcs_parse_pinconf() returns -ENOSUPP, then set num_maps to 1 and proceed normally as it is valid for group to have no pinconf props
- added Fixes: tag thanks to Gustavo A. R. Silva

[0] https://lore.kernel.org/linux-omap/20200531204147.GA664833@x1/

 drivers/pinctrl/pinctrl-single.c | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)
drivers/pinctrl/pinctrl-single.c +7 -5
index 1e0614daee9b..a9d511982780 100644
@@ -916,7 +916,7 @@ static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np,
 
        /* If pinconf isn't supported, don't parse properties in below. */
        if (!PCS_HAS_PINCONF)
-               return 0;
+               return -ENOTSUPP;
 
        /* cacluate how much properties are supported in current node */
        for (i = 0; i < ARRAY_SIZE(prop2); i++) {
@@ -928,7 +928,7 @@ static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np,
                        nconfs++;
        }
        if (!nconfs)
-               return 0;
+               return -ENOTSUPP;
 
        func->conf = devm_kcalloc(pcs->dev,
                                  nconfs, sizeof(struct pcs_conf_vals),
@@ -1056,9 +1056,12 @@ static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs,
 
        if (PCS_HAS_PINCONF && function) {
                res = pcs_parse_pinconf(pcs, np, function, map);
-               if (res)
+               if (res == 0)
+                       *num_maps = 2;
+               else if (res == -ENOTSUPP)
+                       *num_maps = 1;
+               else
                        goto free_pingroups;
-               *num_maps = 2;
        } else {
                *num_maps = 1;
        }
--
Quoted 1 line

2.25.1