power: supply: bq24257_charger: Replace depends on REGMAP_I2C with select
Subsystems (37)
Sasha Levin
maintainerPATCH 1/172 power: supply: bq24257_charger: Replace depends on REGMAP_I2C with select
From: Enric Balletbo i Serra <[email protected]>
[ Upstream commit 87c3d579c8ed0eaea6b1567d529a8daa85a2bc6c ]
regmap is a library function that gets selected by drivers that need it. No driver modules should depend on it. Depending on REGMAP_I2C makes this driver only build if another driver already selected REGMAP_I2C, as the symbol can't be selected through the menu kernel configuration.
--- drivers/power/supply/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/power/supply/Kconfig +1 -1
@@ -555,7 +555,7 @@ config CHARGER_BQ24257 tristate "TI BQ24250/24251/24257 battery charger driver" depends on I2C depends on GPIOLIB || COMPILE_TEST - depends on REGMAP_I2C + select REGMAP_I2C help Say Y to enable support for the TI BQ24250, BQ24251, and BQ24257 battery chargers.
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 2/172 clk: sunxi: Fix incorrect usage of round_down()
From: Rikard Falkeborn <[email protected]>
[ Upstream commit ee25d9742dabed3fd18158b518f846abeb70f319 ]
round_down() can only round to powers of 2. If round_down() is asked to round to something that is not a power of 2, incorrect results are produced. The incorrect results can be both too large and too small.
Instead, use rounddown() which can round to any number.
--- drivers/clk/sunxi/clk-sunxi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/clk/sunxi/clk-sunxi.c +1 -1
@@ -98,7 +98,7 @@ static void sun6i_a31_get_pll1_factors(struct factors_request *req)* Round down the frequency to the closest multiple of either * 6 or 16 */ -u32 round_freq_6 =round_down (freq_mhz,6 ); +u32 round_freq_6 =rounddown (freq_mhz,6 );u32 round_freq_16 =round_down (freq_mhz,16 );if (round_freq_6 > round_freq_16)
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 3/172 ASoC: tegra: tegra_wm8903: Support nvidia, headset property
In reply to Sasha LevinFrom: Dmitry Osipenko <[email protected]>
[ Upstream commit 3ef9d5073b552d56bd6daf2af1e89b7e8d4df183 ]
The microphone-jack state needs to be masked in a case of a 4-pin jack when microphone and ground pins are shorted. Presence of nvidia,headset tells that WM8903 CODEC driver should mask microphone's status if short circuit is detected, i.e headphones are inserted.
--- sound/soc/tegra/tegra_wm8903.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
sound/soc/tegra/tegra_wm8903.c +5 -1
@@ -173,6 +173,7 @@ static int tegra_wm8903_init(struct snd_soc_pcm_runtime *rtd)struct snd_soc_component *component = codec_dai->component;struct snd_soc_card *card = rtd->card;struct tegra_wm8903 *machine =snd_soc_card_get_drvdata (card); +int shrt =0 ;if (gpio_is_valid (machine->gpio_hp_det)) { tegra_wm8903_hp_jack_gpio.gpio = machine->gpio_hp_det;
@@ -185,12 +186,15 @@ static int tegra_wm8903_init(struct snd_soc_pcm_runtime *rtd) &tegra_wm8903_hp_jack_gpio); } +if (of_property_read_bool (card->dev->of_node,"nvidia,headset" )) + shrt =SND_JACK_MICROPHONE ; +snd_soc_card_jack_new (rtd->card,"Mic Jack" ,SND_JACK_MICROPHONE , &tegra_wm8903_mic_jack, tegra_wm8903_mic_jack_pins,ARRAY_SIZE (tegra_wm8903_mic_jack_pins));wm8903_mic_detect (component, &tegra_wm8903_mic_jack,SND_JACK_MICROPHONE , -0 ); + shrt);snd_soc_dapm_force_enable_pin (&card->dapm,"MICBIAS" );
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 4/172 RDMA/uverbs: Make the event_queue fds return POLLERR when disassociated
In reply to Sasha LevinFrom: Jason Gunthorpe <[email protected]>
[ Upstream commit eb356e6dc15a30af604f052cd0e170450193c254 ]
If is_closed is set, and the event list is empty, then read() will return -EIO without blocking. After setting is_closed in ib_uverbs_free_event_queue(), we do trigger a wake_up on the poll_wait, but the fops->poll() function does not check it, so poll will continue to sleep on an empty list.
--- drivers/infiniband/core/uverbs_main.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/infiniband/core/uverbs_main.c +2 -0
@@ -360,6 +360,8 @@ static __poll_t ib_uverbs_event_poll(struct ib_uverbs_event_queue *ev_queue,spin_lock_irq (&ev_queue->lock);if (!list_empty (&ev_queue->event_list)) pollflags =EPOLLIN |EPOLLRDNORM ; +else if (ev_queue->is_closed) + pollflags =EPOLLERR ;spin_unlock_irq (&ev_queue->lock);return pollflags;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 5/172 i2c: piix4: Detect secondary SMBus controller on AMD AM4 chipsets
In reply to Sasha LevinFrom: Adam Honse <[email protected]>
[ Upstream commit f27237c174fd9653033330e4e532cd9d153ce824 ]
The AMD X370 and other AM4 chipsets (A/B/X 3/4/5 parts) and Threadripper equivalents have a secondary SMBus controller at I/O port address 0x0B20. This bus is used by several manufacturers to control motherboard RGB lighting via embedded controllers. I have been using this bus in my OpenRGB project to control the Aura RGB on many motherboards and ASRock also uses this bus for their Polychrome RGB controller.
I am not aware of any CZ-compatible platforms which do not have the second SMBus channel. All of AMD's AM4- and Threadripper- series chipsets that OpenRGB users have tested appear to have this secondary bus. I also noticed this secondary bus is present on older AMD platforms including my FM1 home server.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202587
--- drivers/i2c/busses/i2c-piix4.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/i2c/busses/i2c-piix4.c +2 -1
@@ -958,7 +958,8 @@ static int piix4_probe(struct pci_dev *dev, const struct pci_device_id *id) }if (dev->vendor ==PCI_VENDOR_ID_AMD && - dev->device ==PCI_DEVICE_ID_AMD_HUDSON2_SMBUS ) { + (dev->device ==PCI_DEVICE_ID_AMD_HUDSON2_SMBUS || + dev->device ==PCI_DEVICE_ID_AMD_KERNCZ_SMBUS )) { retval =piix4_setup_sb800 (dev, id,1 ); }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 6/172 iio: pressure: bmp280: Tolerate IRQ before registering
In reply to Sasha LevinFrom: Andy Shevchenko <[email protected]>
[ Upstream commit 97b31a6f5fb95b1ec6575b78a7240baddba34384 ]
With DEBUG_SHIRQ enabled we have a kernel crash
[ 116.482696] BUG: kernel NULL pointer dereference, address: 0000000000000000
...
[ 116.606571] Call Trace: [ 116.609023] <IRQ> [ 116.611047] complete+0x34/0x50 [ 116.614206] bmp085_eoc_irq+0x9/0x10 [bmp280]
because DEBUG_SHIRQ mechanism fires an IRQ before registration and drivers ought to be able to handle an interrupt happening before request_irq() returns.
--- drivers/iio/pressure/bmp280-core.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/iio/pressure/bmp280-core.c +4 -1
@@ -703,7 +703,7 @@ static int bmp180_measure(struct bmp280_data *data, u8 ctrl_meas)unsigned int ctrl;if (data->use_eoc) -init_completion (&data->done); +reinit_completion (&data->done); ret =regmap_write (data->regmap,BMP280_REG_CTRL_MEAS , ctrl_meas);if (ret)
@@ -959,6 +959,9 @@ static int bmp085_fetch_eoc_irq(struct device *dev, "trying to enforce it\n"); irq_trig =IRQF_TRIGGER_RISING ; } + +init_completion (&data->done); + ret = devm_request_threaded_irq(dev, irq, bmp085_eoc_irq,
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 7/172 iio: light: isl29125: fix iio_triggered_buffer_{predisable,postenable} positions
In reply to Sasha LevinFrom: Alexandru Ardelean <[email protected]>
[ Upstream commit 9b7a12c3e090cf3fba6f66f1f23abbc6e0e86021 ]
The iio_triggered_buffer_{predisable,postenable} functions attach/detach the poll functions.
For the predisable hook, the disable code should occur before detaching the poll func, and for the postenable hook, the poll func should be attached before the enable code.
This change reworks the predisable/postenable hooks so that the pollfunc is attached/detached in the correct position.
It also balances the calls a bit, by grouping the preenable and the iio_triggered_buffer_postenable() into a single isl29125_buffer_postenable() function.
--- drivers/iio/light/isl29125.c | 28 +++++++++++++++++++--------- 1 file changed, 19 insertions(+), 9 deletions(-)
drivers/iio/light/isl29125.c +19 -9
@@ -216,13 +216,24 @@ static const struct iio_info isl29125_info = { .attrs = &isl29125_attribute_group, }; -static int isl29125_buffer_preenable (struct iio_dev *indio_dev) +static int isl29125_buffer_postenable (struct iio_dev *indio_dev) {struct isl29125_data *data =iio_priv (indio_dev); +int err; + + err =iio_triggered_buffer_postenable (indio_dev); +if (err) +return err; data->conf1 |=ISL29125_MODE_RGB ; -return i2c_smbus_write_byte_data (data->client,ISL29125_CONF1 , + err =i2c_smbus_write_byte_data (data->client,ISL29125_CONF1 , data->conf1); +if (err) { +iio_triggered_buffer_predisable (indio_dev); +return err; + } + +return 0 ; }static int isl29125_buffer_predisable (struct iio_dev *indio_dev)
@@ -230,19 +241,18 @@ static int isl29125_buffer_predisable(struct iio_dev *indio_dev)struct isl29125_data *data =iio_priv (indio_dev);int ret; - ret =iio_triggered_buffer_predisable (indio_dev); -if (ret <0 ) -return ret; - data->conf1 &= ~ISL29125_MODE_MASK ; data->conf1 |=ISL29125_MODE_PD ; -return i2c_smbus_write_byte_data (data->client,ISL29125_CONF1 , + ret =i2c_smbus_write_byte_data (data->client,ISL29125_CONF1 , data->conf1); + +iio_triggered_buffer_predisable (indio_dev); + +return ret; }static const struct iio_buffer_setup_ops isl29125_buffer_setup_ops = { - .preenable = isl29125_buffer_preenable, - .postenable = &iio_triggered_buffer_postenable, + .postenable = isl29125_buffer_postenable, .predisable = isl29125_buffer_predisable, };
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 8/172 remoteproc: Fix IDR initialisation in rproc_alloc()
In reply to Sasha LevinFrom: Alex Elder <[email protected]>
[ Upstream commit 6442df49400b466431979e7634849a464a5f1861 ]
If ida_simple_get() returns an error when called in rproc_alloc(), put_device() is called to clean things up. By this time the rproc device type has been assigned, with rproc_type_release() as the release function.
The first thing rproc_type_release() does is call:
idr_destroy(&rproc->notifyids);
But at the time the ida_simple_get() call is made, the notifyids field in the remoteproc structure has not been initialized.
I'm not actually sure this case causes an observable problem, but it's incorrect. Fix this by initializing the notifyids field before calling ida_simple_get() in rproc_alloc().
--- drivers/remoteproc/remoteproc_core.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/remoteproc/remoteproc_core.c +1 -2
@@ -1598,6 +1598,7 @@ struct rproc *rproc_alloc(struct device *dev, const char *name, rproc->dev.type = &rproc_type; rproc->dev.class = &rproc_class; rproc->dev.driver_data = rproc; +idr_init (&rproc->notifyids);/* Assign a unique device index and name */ rproc->index =ida_simple_get (&rproc_dev_index,0 ,0 ,GFP_KERNEL );
@@ -1622,8 +1623,6 @@ struct rproc *rproc_alloc(struct device *dev, const char *name,mutex_init (&rproc->lock); -idr_init (&rproc->notifyids); -INIT_LIST_HEAD (&rproc->carveouts);INIT_LIST_HEAD (&rproc->mappings);INIT_LIST_HEAD (&rproc->traces);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 9/172 clk: qcom: msm8916: Fix the address location of pll->config_reg
In reply to Sasha LevinFrom: Bryan O'Donoghue <[email protected]>
[ Upstream commit f47ab3c2f5338828a67e89d5f688d2cef9605245 ]
During the process of debugging a processor derived from the msm8916 which we found the new processor was not starting one of its PLLs.
After tracing the addresses and writes that downstream was doing and comparing to upstream it became obvious that we were writing to a different register location than downstream when trying to configure the PLL.
This error is also present in upstream msm8916.
As an example clk-pll.c::clk_pll_recalc_rate wants to write to pll->config_reg updating the bit-field POST_DIV_RATIO. That bit-field is defined in PLL_USER_CTL not in PLL_CONFIG_CTL. Taking the BIMC PLL as an example
lm80-p0436-13_c_qc_snapdragon_410_processor_hrd.pdf
0x01823010 GCC_BIMC_PLL_USER_CTL0x01823014 GCC_BIMC_PLL_CONFIG_CTL
This pattern is repeated for gpll0, gpll1, gpll2 and bimc_pll.
This error is likely not apparent since the bootloader will already have initialized these PLLs.
This patch corrects the location of config_reg from PLL_CONFIG_CTL to PLL_USER_CTL for all relevant PLLs on msm8916.
Fixes commit 3966fab8b6ab ("clk: qcom: Add MSM8916 Global Clock Controller support")
--- drivers/clk/qcom/gcc-msm8916.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/clk/qcom/gcc-msm8916.c +4 -4
@@ -268,7 +268,7 @@ static struct clk_pll gpll0 = { .l_reg = 0x21004, .m_reg = 0x21008, .n_reg = 0x2100c, - .config_reg = 0x21014, + .config_reg = 0x21010, .mode_reg = 0x21000, .status_reg = 0x2101c, .status_bit = 17,
@@ -295,7 +295,7 @@ static struct clk_pll gpll1 = { .l_reg = 0x20004, .m_reg = 0x20008, .n_reg = 0x2000c, - .config_reg = 0x20014, + .config_reg = 0x20010, .mode_reg = 0x20000, .status_reg = 0x2001c, .status_bit = 17,
@@ -322,7 +322,7 @@ static struct clk_pll gpll2 = { .l_reg = 0x4a004, .m_reg = 0x4a008, .n_reg = 0x4a00c, - .config_reg = 0x4a014, + .config_reg = 0x4a010, .mode_reg = 0x4a000, .status_reg = 0x4a01c, .status_bit = 17,
@@ -349,7 +349,7 @@ static struct clk_pll bimc_pll = { .l_reg = 0x23004, .m_reg = 0x23008, .n_reg = 0x2300c, - .config_reg = 0x23014, + .config_reg = 0x23010, .mode_reg = 0x23000, .status_reg = 0x2301c, .status_bit = 17,
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 10/172 backlight: lp855x: Ensure regulators are disabled on probe failure
In reply to Sasha LevinFrom: Jon Hunter <[email protected]>
[ Upstream commit d8207c155a7c6015eb7f43739baa7dfb1fa638af ]
If probing the LP885x backlight fails after the regulators have been enabled, then the following warning is seen when releasing the regulators ...
WARNING: CPU: 1 PID: 289 at drivers/regulator/core.c:2051 _regulator_put.part.28+0x158/0x160 Modules linked in: tegra_xudc lp855x_bl(+) host1x pwm_tegra ip_tables x_tables ipv6 nf_defrag_ipv6 CPU: 1 PID: 289 Comm: systemd-udevd Not tainted 5.6.0-rc2-next-20200224 #1 Hardware name: NVIDIA Jetson TX1 Developer Kit (DT)
...
Call trace: _regulator_put.part.28+0x158/0x160 regulator_put+0x34/0x50 devm_regulator_release+0x10/0x18 release_nodes+0x12c/0x230 devres_release_all+0x34/0x50 really_probe+0x1c0/0x370 driver_probe_device+0x58/0x100 device_driver_attach+0x6c/0x78 __driver_attach+0xb0/0xf0 bus_for_each_dev+0x68/0xc8 driver_attach+0x20/0x28 bus_add_driver+0x160/0x1f0 driver_register+0x60/0x110 i2c_register_driver+0x40/0x80 lp855x_driver_init+0x20/0x1000 [lp855x_bl] do_one_initcall+0x58/0x1a0 do_init_module+0x54/0x1d0 load_module+0x1d80/0x21c8 __do_sys_finit_module+0xe8/0x100 __arm64_sys_finit_module+0x18/0x20 el0_svc_common.constprop.3+0xb0/0x168 do_el0_svc+0x20/0x98 el0_sync_handler+0xf4/0x1b0 el0_sync+0x140/0x180
Fix this by ensuring that the regulators are disabled, if enabled, on probe failure.
Finally, ensure that the vddio regulator is disabled in the driver remove handler.
--- drivers/video/backlight/lp855x_bl.c | 20 ++++++++++++++++---- 1 file changed, 16 insertions(+), 4 deletions(-)
drivers/video/backlight/lp855x_bl.c +16 -4
@@ -460,7 +460,7 @@ static int lp855x_probe(struct i2c_client *cl, const struct i2c_device_id *id) ret =regulator_enable (lp->enable);if (ret <0 ) {dev_err (lp->dev,"failed to enable vddio: %d\n" , ret); -return ret; + goto disable_supply; }/*
@@ -475,24 +475,34 @@ static int lp855x_probe(struct i2c_client *cl, const struct i2c_device_id *id) ret =lp855x_configure (lp);if (ret) {dev_err (lp->dev,"device config err: %d" , ret); -return ret; + goto disable_vddio; } ret =lp855x_backlight_register (lp);if (ret) {dev_err (lp->dev,"failed to register backlight. err: %d\n" , ret); -return ret; + goto disable_vddio; } ret =sysfs_create_group (&lp->dev->kobj, &lp855x_attr_group);if (ret) {dev_err (lp->dev,"failed to register sysfs. err: %d\n" , ret); -return ret; + goto disable_vddio; }backlight_update_status (lp->bl); +return 0 ; + +disable_vddio: +if (lp->enable) +regulator_disable (lp->enable); +disable_supply: +if (lp->supply) +regulator_disable (lp->supply); + +return ret; }static int lp855x_remove (struct i2c_client *cl)
@@ -501,6 +511,8 @@ static int lp855x_remove(struct i2c_client *cl) lp->bl->props.brightness =0 ;backlight_update_status (lp->bl); +if (lp->enable) +regulator_disable (lp->enable);if (lp->supply)regulator_disable (lp->supply);sysfs_remove_group (&lp->dev->kobj, &lp855x_attr_group);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 11/172 ASoC: davinci-mcasp: Fix dma_chan refcnt leak when getting dma type
In reply to Sasha LevinFrom: Xiyu Yang <[email protected]>
[ Upstream commit a697ae6ea56e23397341b027098c1b11d9ab13da ]
davinci_mcasp_get_dma_type() invokes dma_request_chan(), which returns a reference of the specified dma_chan object to "chan" with increased refcnt.
When davinci_mcasp_get_dma_type() returns, local variable "chan" becomes invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of davinci_mcasp_get_dma_type(). When chan device is NULL, the function forgets to decrease the refcnt increased by dma_request_chan(), causing a refcnt leak.
Fix this issue by calling dma_release_channel() when chan device is NULL.
--- sound/soc/davinci/davinci-mcasp.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
sound/soc/davinci/davinci-mcasp.c +3 -1
@@ -1758,8 +1758,10 @@ static int davinci_mcasp_get_dma_type(struct davinci_mcasp *mcasp) PTR_ERR(chan));return PTR_ERR (chan); } -if (WARN_ON (!chan->device || !chan->device->dev)) +if (WARN_ON (!chan->device || !chan->device->dev)) { +dma_release_channel (chan);return -EINVAL ; + }if (chan->device->dev->of_node) ret = of_property_read_string(chan->device->dev->of_node,
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 12/172 ARM: integrator: Add some Kconfig selections
In reply to Sasha LevinFrom: Linus Walleij <[email protected]>
[ Upstream commit d2854bbe5f5c4b4bec8061caf4f2e603d8819446 ]
The CMA and DMA_CMA Kconfig options need to be selected by the Integrator in order to produce boot console on some Integrator systems.
The REGULATOR and REGULATOR_FIXED_VOLTAGE need to be selected in order to boot the system from an external MMC card when using MMCI/PL181 from the device tree probe path.
Select these things directly from the Kconfig so we are sure to be able to bring the systems up with console from any device tree.
--- arch/arm/mach-integrator/Kconfig | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
arch/arm/mach-integrator/Kconfig +4 -3
@@ -3,6 +3,8 @@ menuconfig ARCH_INTEGRATOR depends on ARCH_MULTI_V4T || ARCH_MULTI_V5 || ARCH_MULTI_V6 select ARM_AMBA select COMMON_CLK_VERSATILE + select CMA + select DMA_CMA select HAVE_TCM select ICST select MFD_SYSCON
@@ -34,14 +36,13 @@ config INTEGRATOR_IMPD1 select ARM_VIC select GPIO_PL061 select GPIOLIB + select REGULATOR + select REGULATOR_FIXED_VOLTAGE help The IM-PD1 is an add-on logic module for the Integrator which allows ARM(R) Ltd PrimeCells to be developed and evaluated. The IM-PD1 can be found on the Integrator/PP2 platform. - To compile this driver as a module, choose M here: the - module will be called impd1. - config INTEGRATOR_CM7TDMI bool "Integrator/CM7TDMI core module" depends on ARCH_INTEGRATOR_AP
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Sasha Levin
maintainerPATCH 13/172 scsi: qedi: Check for buffer overflow in qedi_set_path()
In reply to Sasha LevinFrom: Dan Carpenter <[email protected]>
[ Upstream commit 4a4c0cfb4be74e216dd4446b254594707455bfc6 ]
Smatch complains that the "path_data->handle" variable is user controlled. It comes from iscsi_set_path() so that seems possible. It's harmless to add a limit check.
The qedi->ep_tbl[] array has qedi->max_active_conns elements (which is always ISCSI_MAX_SESS_PER_HBA (4096) elements). The array is allocated in the qedi_cm_alloc_mem() function.
--- drivers/scsi/qedi/qedi_iscsi.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/scsi/qedi/qedi_iscsi.c +4 -0
@@ -1217,6 +1217,10 @@ static int qedi_set_path(struct Scsi_Host *shost, struct iscsi_path *path_data) } iscsi_cid = (u32 )path_data->handle; +if (iscsi_cid >= qedi->max_active_conns) { + ret = -EINVAL ; + goto set_path_exit; + } qedi_ep = qedi->ep_tbl[iscsi_cid];QEDI_INFO (&qedi->dbg_ctx,QEDI_LOG_INFO ,"iscsi_cid=0x%x, qedi_ep=%p\n" , iscsi_cid, qedi_ep);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 14/172 ALSA: hda/realtek - Introduce polarity for micmute LED GPIO
In reply to Sasha LevinFrom: Kai-Heng Feng <[email protected]>
[ Upstream commit dbd13179780555ecd3c992dea1222ca31920e892 ]
Currently mute LED and micmute LED share the same GPIO polarity.
So split the polarity for mute and micmute, in case they have different polarities.
--- sound/pci/hda/patch_realtek.c | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-)
sound/pci/hda/patch_realtek.c +8 -6
@@ -94,6 +94,7 @@ struct alc_spec {/* mute LED for HP laptops, see alc269_fixup_mic_mute_hook() */ int mute_led_polarity; +int micmute_led_polarity;hda_nid_t mute_led_nid;hda_nid_t cap_mute_led_nid;
@@ -3862,11 +3863,9 @@ static void alc269_fixup_hp_mute_led_mic3(struct hda_codec *codec,/* update LED status via GPIO */ static void alc_update_gpio_led (struct hda_codec *codec,unsigned int mask, -bool enabled) +int polarity,bool enabled) { -struct alc_spec *spec = codec->spec; - -if (spec->mute_led_polarity) +if (polarity) enabled = !enabled;alc_update_gpio_data (codec, mask, !enabled);/* muted -> LED on */ }
@@ -3877,7 +3876,8 @@ static void alc_fixup_gpio_mute_hook(void *private_data, int enabled)struct hda_codec *codec = private_data;struct alc_spec *spec = codec->spec; -alc_update_gpio_led (codec, spec->gpio_mute_led_mask, enabled); +alc_update_gpio_led (codec, spec->gpio_mute_led_mask, + spec->mute_led_polarity, enabled); }/* turn on/off mic-mute LED via GPIO per capture hook */
@@ -3886,6 +3886,7 @@ static void alc_gpio_micmute_update(struct hda_codec *codec)struct alc_spec *spec = codec->spec;alc_update_gpio_led (codec, spec->gpio_mic_led_mask, + spec->micmute_led_polarity, spec->gen.micmute_led.led_value); }
@@ -5476,7 +5477,8 @@ static void alc280_hp_gpio4_automute_hook(struct hda_codec *codec,snd_hda_gen_hp_automute (codec, jack);/* mute_led_polarity is set to 0, so we pass inverted value here */ -alc_update_gpio_led (codec,0x10 , !spec->gen.hp_jack_present); +alc_update_gpio_led (codec,0x10 , spec->mute_led_polarity, + !spec->gen.hp_jack_present); }/* Manage GPIOs for HP EliteBook Folio 9480m.
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 15/172 ALSA: isa/wavefront: prevent out of bounds write in ioctl
In reply to Sasha LevinFrom: Dan Carpenter <[email protected]>
[ Upstream commit 7f0d5053c5a9d23fe5c2d337495a9d79038d267b ]
The "header->number" comes from the ioctl and it needs to be clamped to prevent out of bounds writes.
--- sound/isa/wavefront/wavefront_synth.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-)
sound/isa/wavefront/wavefront_synth.c +7 -1
@@ -1175,7 +1175,10 @@ wavefront_send_alias (snd_wavefront_t *dev, wavefront_patch_info *header)"alias for %d\n" , header->number, header->hdr.a.OriginalSample); - + +if (header->number >=WF_MAX_SAMPLE ) +return -EINVAL ; +munge_int32 (header->number, &alias_hdr[0 ],2 );munge_int32 (header->hdr.a.OriginalSample, &alias_hdr[2 ],2 ); munge_int32 (*((unsigned int *)&header->hdr.a.sampleStartOffset),
@@ -1206,6 +1209,9 @@ wavefront_send_multisample (snd_wavefront_t *dev, wavefront_patch_info *header)int num_samples;unsigned char *msample_hdr; +if (header->number >=WF_MAX_SAMPLE ) +return -EINVAL ; + msample_hdr =kmalloc (WF_MSAMPLE_BYTES ,GFP_KERNEL );if (! msample_hdr)return -ENOMEM ;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 16/172 PCI: Allow pci_resize_resource() for devices on root bus
In reply to Sasha LevinFrom: Ard Biesheuvel <[email protected]>
[ Upstream commit d09ddd8190fbdc07696bf34b548ae15aa1816714 ]
When resizing a BAR, pci_reassign_bridge_resources() is invoked to bring the bridge windows of parent bridges in line with the new BAR assignment.
This assumes the device whose BAR is being resized lives on a subordinate bus, but this is not necessarily the case. A device may live on the root bus, in which case dev->bus->self is NULL, and passing a NULL pci_dev pointer to pci_reassign_bridge_resources() will cause it to crash.
So let's make the call to pci_reassign_bridge_resources() conditional on whether dev->bus->self is non-NULL in the first place.
--- drivers/pci/setup-res.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-)
drivers/pci/setup-res.c +5 -4
@@ -439,10 +439,11 @@ int pci_resize_resource(struct pci_dev *dev, int resno, int size) res->end = res->start +pci_rebar_size_to_bytes (size) -1 ;/* Check if the new config works by trying to assign everything. */ - ret =pci_reassign_bridge_resources (dev->bus->self, res->flags); -if (ret) - goto error_resize; - +if (dev->bus->self) { + ret =pci_reassign_bridge_resources (dev->bus->self, res->flags); +if (ret) + goto error_resize; + }return 0 ; error_resize:
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 17/172 Smack: slab-out-of-bounds in vsscanf
In reply to Sasha LevinFrom: Casey Schaufler <[email protected]>
[ Upstream commit 84e99e58e8d1e26f04c097f4266e431a33987f36 ]
Add barrier to soob. Return -EOVERFLOW if the buffer is exceeded.
--- security/smack/smackfs.c | 10 ++++++++++ 1 file changed, 10 insertions(+)
security/smack/smackfs.c +10 -0
@@ -906,11 +906,21 @@ static ssize_t smk_set_cipso(struct file *file, const char __user *buf,else rule +=strlen (skp->smk_known) +1 ; +if (rule > data + count) { + rc = -EOVERFLOW ; + goto out; + } + ret =sscanf (rule,"%d" , &maplevel);if (ret !=1 || maplevel >SMACK_CIPSO_MAXLEVEL ) goto out; rule +=SMK_DIGITLEN ; +if (rule > data + count) { + rc = -EOVERFLOW ; + goto out; + } + ret =sscanf (rule,"%d" , &catlen);if (ret !=1 || catlen >SMACK_CIPSO_MAXCATNUM ) goto out;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 18/172 scsi: qla2xxx: Fix issue with adapter's stopping state
In reply to Sasha LevinFrom: Viacheslav Dubeyko <[email protected]>
[ Upstream commit 803e45550b11c8e43d89812356fe6f105adebdf9 ]
The goal of the following command sequence is to restart the adapter. However, the tgt_stop flag remains set, indicating that the adapter is still in stopping state even after re-enabling it.
echo 0x7fffffff > /sys/module/qla2xxx/parameters/logging modprobe target_core_mod
modprobe tcm_qla2xxx
mkdir /sys/kernel/config/target/qla2xxx
mkdir /sys/kernel/config/target/qla2xxx/<port-name>
mkdir /sys/kernel/config/target/qla2xxx/<port-name>/tpgt_1 echo 1 > /sys/kernel/config/target/qla2xxx/<port-name>/tpgt_1/enable echo 0 > /sys/kernel/config/target/qla2xxx/<port-name>/tpgt_1/enable echo 1 > /sys/kernel/config/target/qla2xxx/<port-name>/tpgt_1/enable
kernel: PID 1396:qla_target.c:1555 qlt_stop_phase1(): tgt_stop 0x0, tgt_stopped 0x0
kernel: qla2xxx [0001:00:02.0]-e803:1: PID 1396:qla_target.c:1567: Stopping target for host 1(c0000000033557e8)
kernel: PID 1396:qla_target.c:1579 qlt_stop_phase1(): tgt_stop 0x1, tgt_stopped 0x0
kernel: PID 1396:qla_target.c:1266 qlt_schedule_sess_for_deletion(): tgt_stop 0x1, tgt_stopped 0x0
kernel: qla2xxx [0001:00:02.0]-e801:1: PID 1396:qla_target.c:1316: Scheduling sess c00000002d5cd800 for deletion 21:00:00:24:ff:7f:35:c7 <skipped>
kernel: qla2xxx [0001:00:02.0]-290a:1: PID 340:qla_target.c:1187: qlt_unreg_sess sess c00000002d5cd800 for deletion 21:00:00:24:ff:7f:35:c7 <skipped>
kernel: qla2xxx [0001:00:02.0]-f801:1: PID 340:qla_target.c:1145: Unregistration of sess c00000002d5cd800 21:00:00:24:ff:7f:35:c7 finished fcp_cnt 0
kernel: PID 340:qla_target.c:1155 qlt_free_session_done(): tgt_stop 0x1, tgt_stopped 0x0
kernel: qla2xxx [0001:00:02.0]-4807:1: PID 346:qla_os.c:6329: ISP abort scheduled.
<skipped>
kernel: qla2xxx [0001:00:02.0]-28f1:1: PID 346:qla_os.c:3956: Mark all dev lost
kernel: PID 346:qla_target.c:1266 qlt_schedule_sess_for_deletion(): tgt_stop 0x1, tgt_stopped 0x0
kernel: qla2xxx [0001:00:02.0]-4808:1: PID 346:qla_os.c:6338: ISP abort end.
<skipped>
kernel: PID 1396:qla_target.c:6812 qlt_enable_vha(): tgt_stop 0x1, tgt_stopped 0x0
<skipped>
kernel: qla2xxx [0001:00:02.0]-4807:1: PID 346:qla_os.c:6329: ISP abort scheduled.
<skipped>
kernel: qla2xxx [0001:00:02.0]-4808:1: PID 346:qla_os.c:6338: ISP abort end.
qlt_handle_cmd_for_atio() rejects the request to send commands because the adapter is in the stopping state:
kernel: PID 0:qla_target.c:4442 qlt_handle_cmd_for_atio(): tgt_stop 0x1, tgt_stopped 0x0
kernel: qla2xxx [0001:00:02.0]-3861:1: PID 0:qla_target.c:4447: New command while device c000000005314600 is shutting down
kernel: qla2xxx [0001:00:02.0]-e85f:1: PID 0:qla_target.c:5728: qla_target: Unable to send command to target
This patch calls qla_stop_phase2() in addition to qlt_stop_phase1() in tcm_qla2xxx_tpg_enable_store() and tcm_qla2xxx_npiv_tpg_enable_store(). The qlt_stop_phase1() marks adapter as stopping (tgt_stop == 0x1, tgt_stopped == 0x0) but qlt_stop_phase2() marks adapter as stopped (tgt_stop == 0x0, tgt_stopped == 0x1).
--- drivers/scsi/qla2xxx/tcm_qla2xxx.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/scsi/qla2xxx/tcm_qla2xxx.c +2 -0
@@ -960,6 +960,7 @@ static ssize_t tcm_qla2xxx_tpg_enable_store(struct config_item *item,atomic_set (&tpg->lport_tpg_enabled,0 );qlt_stop_phase1 (vha->vha_tgt.qla_tgt); +qlt_stop_phase2 (vha->vha_tgt.qla_tgt); }return count;
@@ -1122,6 +1123,7 @@ static ssize_t tcm_qla2xxx_npiv_tpg_enable_store(struct config_item *item,atomic_set (&tpg->lport_tpg_enabled,0 );qlt_stop_phase1 (vha->vha_tgt.qla_tgt); +qlt_stop_phase2 (vha->vha_tgt.qla_tgt); }return count;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 19/172 iio: bmp280: fix compensation of humidity
In reply to Sasha LevinFrom: Andreas Klinger <[email protected]>
[ Upstream commit dee2dabc0e4115b80945fe2c91603e634f4b4686 ]
Limit the output of humidity compensation to the range between 0 and 100 percent.
Depending on the calibration parameters of the individual sensor it happens, that a humidity above 100 percent or below 0 percent is calculated, which don't make sense in terms of relative humidity.
Add a clamp to the compensation formula as described in the datasheet of the sensor in chapter 4.2.3.
Although this clamp is documented, it was never in the driver of the kernel.
It depends on the circumstances (calibration parameters, temperature, humidity) if one can see a value above 100 percent without the clamp. The writer of this patch was working with this type of sensor without noting this error. So it seems to be a rare event when this bug occures.
--- drivers/iio/pressure/bmp280-core.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/iio/pressure/bmp280-core.c +2 -0
@@ -261,6 +261,8 @@ static u32 bmp280_compensate_humidity(struct bmp280_data *data, + (s32)2097152) * calib->H2 + 8192) >> 14); var -= ((((var >>15 ) * (var >>15 )) >>7 ) * (s32 )calib->H1) >>4 ; + var =clamp_val (var,0 ,419430400 ); +return var >>12 ; };
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 20/172 f2fs: report delalloc reserve as non-free in statfs for project quota
In reply to Sasha LevinFrom: Konstantin Khlebnikov <[email protected]>
[ Upstream commit baaa7ebf25c78c5cb712fac16b7f549100beddd3 ]
This reserved space isn't committed yet but cannot be used for allocations. For userspace it has no difference from used space.
See the same fix in ext4 commit f06925c73942 ("ext4: report delalloc reserve as non-free in statfs for project quota").
--- fs/f2fs/super.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
fs/f2fs/super.c +2 -1
@@ -1154,7 +1154,8 @@ static int f2fs_statfs_project(struct super_block *sb, limit >>= sb->s_blocksize_bits;if (limit && buf->f_blocks > limit) { - curblock = dquot->dq_dqb.dqb_curspace >> sb->s_blocksize_bits; + curblock = (dquot->dq_dqb.dqb_curspace + + dquot->dq_dqb.dqb_rsvspace) >> sb->s_blocksize_bits; buf->f_blocks = limit; buf->f_bfree = buf->f_bavail = (buf->f_blocks > curblock) ?
Signature · 8 lines
2.25.1 _______________________________________________ Linux-f2fs-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/linux-f2fs-devel
Sasha Levin
maintainerPATCH 21/172 i2c: pxa: clear all master action bits in i2c_pxa_stop_message()
In reply to Sasha LevinFrom: Russell King <[email protected]>
[ Upstream commit e81c979f4e071d516aa27cf5a0c3939da00dc1ca ]
If we timeout during a message transfer, the control register may contain bits that cause an action to be set. Read-modify-writing the register leaving these bits set may trigger the hardware to attempt one of these actions unintentionally.
Always clear these bits when cleaning up after a message or after a timeout.
--- drivers/i2c/busses/i2c-pxa.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-)
drivers/i2c/busses/i2c-pxa.c +2 -4
@@ -709,11 +709,9 @@ static inline void i2c_pxa_stop_message(struct pxa_i2c *i2c) {u32 icr; -/* -* Clear the STOP and ACK flags -*/ +/* Clear the START, STOP, ACK, TB and MA flags */ icr =readl (_ICR (i2c)); - icr &= ~(ICR_STOP |ICR_ACKNAK ); + icr &= ~(ICR_START |ICR_STOP |ICR_ACKNAK |ICR_TB |ICR_MA );writel (icr,_ICR (i2c)); }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 22/172 clk: samsung: Mark top ISP and CAM clocks on Exynos542x as critical
In reply to Sasha LevinFrom: Marek Szyprowski <[email protected]>
[ Upstream commit e47bd937e602bb4379546095d1bd0b9871fa60c2 ]
The TOP 'aclk*_isp', 'aclk550_cam', 'gscl_wa' and 'gscl_wb' clocks must be kept enabled all the time to allow proper access to power management control for the ISP and CAM power domains. The last two clocks, although related to GScaler device and GSCL power domain, provides also the I_WRAP_CLK signal to MIPI CSIS0/1 devices, which are a part of CAM power domain and are needed for proper power on/off sequence.
Currently there are no drivers for the devices, which are part of CAM and ISP power domains yet. This patch only fixes the race between disabling the unused power domains and disabling unused clocks, which randomly resulted in the following error during boot:
Power domain CAM disable failed
Power domain ISP disable failed
--- drivers/clk/samsung/clk-exynos5420.c | 16 +++++++++------- 1 file changed, 9 insertions(+), 7 deletions(-)
drivers/clk/samsung/clk-exynos5420.c +9 -7
@@ -597,7 +597,7 @@ static const struct samsung_div_clock exynos5800_div_clks[] __initconst = {static const struct samsung_gate_clock exynos5800_gate_clks[]__initconst = {GATE (CLK_ACLK550_CAM ,"aclk550_cam" ,"mout_user_aclk550_cam" , -GATE_BUS_TOP ,24 ,0 ,0 ), +GATE_BUS_TOP ,24 ,CLK_IS_CRITICAL ,0 ),GATE (CLK_ACLK432_SCALER ,"aclk432_scaler" ,"mout_user_aclk432_scaler" ,GATE_BUS_TOP ,27 ,CLK_IS_CRITICAL ,0 ), GATE(CLK_MAU_EPLL, "mau_epll", "mout_user_mau_epll",
@@ -984,25 +984,25 @@ static const struct samsung_gate_clock exynos5x_gate_clks[] __initconst = {GATE (0 ,"aclk300_jpeg" ,"mout_user_aclk300_jpeg" ,GATE_BUS_TOP ,4 ,CLK_IGNORE_UNUSED ,0 ),GATE (0 ,"aclk333_432_isp0" ,"mout_user_aclk333_432_isp0" , -GATE_BUS_TOP ,5 ,0 ,0 ), +GATE_BUS_TOP ,5 ,CLK_IS_CRITICAL ,0 ),GATE (0 ,"aclk300_gscl" ,"mout_user_aclk300_gscl" ,GATE_BUS_TOP ,6 ,CLK_IS_CRITICAL ,0 ),GATE (0 ,"aclk333_432_gscl" ,"mout_user_aclk333_432_gscl" ,GATE_BUS_TOP ,7 ,CLK_IGNORE_UNUSED ,0 ),GATE (0 ,"aclk333_432_isp" ,"mout_user_aclk333_432_isp" , -GATE_BUS_TOP ,8 ,0 ,0 ), +GATE_BUS_TOP ,8 ,CLK_IS_CRITICAL ,0 ),GATE (CLK_PCLK66_GPIO ,"pclk66_gpio" ,"mout_user_pclk66_gpio" ,GATE_BUS_TOP ,9 ,CLK_IGNORE_UNUSED ,0 ),GATE (0 ,"aclk66_psgen" ,"mout_user_aclk66_psgen" ,GATE_BUS_TOP ,10 ,CLK_IGNORE_UNUSED ,0 ),GATE (0 ,"aclk266_isp" ,"mout_user_aclk266_isp" , -GATE_BUS_TOP ,13 ,0 ,0 ), +GATE_BUS_TOP ,13 ,CLK_IS_CRITICAL ,0 ),GATE (0 ,"aclk166" ,"mout_user_aclk166" ,GATE_BUS_TOP ,14 ,CLK_IGNORE_UNUSED ,0 ),GATE (CLK_ACLK333 ,"aclk333" ,"mout_user_aclk333" ,GATE_BUS_TOP ,15 ,CLK_IS_CRITICAL ,0 ),GATE (0 ,"aclk400_isp" ,"mout_user_aclk400_isp" , -GATE_BUS_TOP ,16 ,0 ,0 ), +GATE_BUS_TOP ,16 ,CLK_IS_CRITICAL ,0 ),GATE (0 ,"aclk400_mscl" ,"mout_user_aclk400_mscl" ,GATE_BUS_TOP ,17 ,CLK_IS_CRITICAL ,0 ), GATE(0, "aclk200_disp1", "mout_user_aclk200_disp1",
@@ -1208,8 +1208,10 @@ static const struct samsung_gate_clock exynos5x_gate_clks[] __initconst = { GATE_IP_GSCL1, 3, 0, 0),GATE (CLK_SMMU_FIMCL1 ,"smmu_fimcl1" ,"dout_gscl_blk_333" ,GATE_IP_GSCL1 ,4 ,0 ,0 ), -GATE (CLK_GSCL_WA ,"gscl_wa" ,"sclk_gscl_wa" ,GATE_IP_GSCL1 ,12 ,0 ,0 ), -GATE (CLK_GSCL_WB ,"gscl_wb" ,"sclk_gscl_wb" ,GATE_IP_GSCL1 ,13 ,0 ,0 ), +GATE (CLK_GSCL_WA ,"gscl_wa" ,"sclk_gscl_wa" ,GATE_IP_GSCL1 ,12 , +CLK_IS_CRITICAL ,0 ), +GATE (CLK_GSCL_WB ,"gscl_wb" ,"sclk_gscl_wb" ,GATE_IP_GSCL1 ,13 , +CLK_IS_CRITICAL ,0 ),GATE (CLK_SMMU_FIMCL3 ,"smmu_fimcl3," ,"dout_gscl_blk_333" ,GATE_IP_GSCL1 ,16 ,0 ,0 ), GATE(CLK_FIMC_LITE3, "fimc_lite3", "aclk333_432_gscl",
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Sasha Levin
maintainerPATCH 23/172 usblp: poison URBs upon disconnect
In reply to Sasha LevinFrom: Oliver Neukum <[email protected]>
[ Upstream commit 296a193b06120aa6ae7cf5c0d7b5e5b55968026e ]
syzkaller reported an URB that should have been killed to be active. We do not understand it, but this should fix the issue if it is real.
--- drivers/usb/class/usblp.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/usb/class/usblp.c +4 -1
@@ -468,7 +468,8 @@ static int usblp_release(struct inode *inode, struct file *file)usb_autopm_put_interface (usblp->intf);if (!usblp->present)/* finish cleanup from disconnect */ -usblp_cleanup (usblp); +usblp_cleanup (usblp);/* any URBs must be dead */ +mutex_unlock (&usblp_mutex);return 0 ; }
@@ -1375,9 +1376,11 @@ static void usblp_disconnect(struct usb_interface *intf)usblp_unlink_urbs (usblp);mutex_unlock (&usblp->mut); +usb_poison_anchored_urbs (&usblp->urbs);if (!usblp->used)usblp_cleanup (usblp); +mutex_unlock (&usblp_mutex); }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 24/172 serial: 8250: Fix max baud limit in generic 8250 port
In reply to Sasha LevinFrom: Serge Semin <[email protected]>
[ Upstream commit 7b668c064ec33f3d687c3a413d05e355172e6c92 ]
Standard 8250 UART ports are designed in a way so they can communicate with baud rates up to 1/16 of a reference frequency. It's expected from most of the currently supported UART controllers. That's why the former version of serial8250_get_baud_rate() method called uart_get_baud_rate() with min and max baud rates passed as (port->uartclk / 16 / UART_DIV_MAX) and ((port->uartclk + tolerance) / 16) respectively. Doing otherwise, like it was suggested in commit ("serial: 8250_mtk: support big baud rate."), caused acceptance of bauds, which was higher than the normal UART controllers actually supported. As a result if some user-space program requested to set a baud greater than (uartclk / 16) it would have been permitted without truncation, but then serial8250_get_divisor(baud) (which calls uart_get_divisor() to get the reference clock divisor) would have returned a zero divisor. Setting zero divisor will cause an unpredictable effect varying from chip to chip. In case of DW APB UART the communications just stop.
Lets fix this problem by getting back the limitation of (uartclk + tolerance) / 16 maximum baud supported by the generic 8250 port. Mediatek 8250 UART ports driver developer shouldn't have touched it in the first place notably seeing he already provided a custom version of set_termios() callback in that glue-driver which took into account the extended baud rate values and accordingly updated the standard and vendor-specific divisor latch registers anyway.
--- drivers/tty/serial/8250/8250_port.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/tty/serial/8250/8250_port.c +3 -1
@@ -2628,6 +2628,8 @@ static unsigned int serial8250_get_baud_rate(struct uart_port *port,struct ktermios *termios, struct ktermios *old) { + unsigned int tolerance = port->uartclk / 100; +/* * Ask the core to calculate the divisor for us. * Allow 1% tolerance at the upper limit so uart clks marginally
@@ -2636,7 +2638,7 @@ static unsigned int serial8250_get_baud_rate(struct uart_port *port,*/ return uart_get_baud_rate (port, termios, old, port->uartclk /16 /UART_DIV_MAX , - port->uartclk); + (port->uartclk + tolerance) /16 ); }void
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 25/172 dm mpath: switch paths in dm_blk_ioctl() code path
In reply to Sasha LevinFrom: Martin Wilck <[email protected]>
[ Upstream commit 2361ae595352dec015d14292f1b539242d8446d6 ]
SCSI LUN passthrough code such as qemu's "scsi-block" device model pass every IO to the host via SG_IO ioctls. Currently, dm-multipath calls choose_pgpath() only in the block IO code path, not in the ioctl code path (unless current_pgpath is NULL). This has the effect that no path switching and thus no load balancing is done for SCSI-passthrough IO, unless the active path fails.
Fix this by using the same logic in multipath_prepare_ioctl() as in multipath_clone_and_map().
Note: The allegedly best path selection algorithm, service-time, still wouldn't work perfectly, because the io size of the current request is always set to 0. Changing that for the IO passthrough case would require the ioctl cmd and arg to be passed to dm's prepare_ioctl() method.
--- drivers/md/dm-mpath.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/md/dm-mpath.c +1 -1
@@ -1868,7 +1868,7 @@ static int multipath_prepare_ioctl(struct dm_target *ti,int r; current_pgpath =READ_ONCE (m->current_pgpath); -if (!current_pgpath) +if (!current_pgpath || !test_bit (MPATHF_QUEUE_IO , &m->flags)) current_pgpath =choose_pgpath (m,0 );if (current_pgpath) {
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 26/172 PCI: aardvark: Don't blindly enable ASPM L0s and don't write to read-only register
In reply to Sasha LevinFrom: Pali Rohár <[email protected]>
[ Upstream commit 90c6cb4a355e7befcb557d217d1d8b8bd5875a05 ]
Trying to change Link Status register does not have any effect as this is a read-only register. Trying to overwrite bits for Negotiated Link Width does not make sense.
In future proper change of link width can be done via Lane Count Select bits in PCIe Control 0 register.
Trying to unconditionally enable ASPM L0s via ASPM Control bits in Link Control register is wrong. There should be at least some detection if endpoint supports L0s as isn't mandatory.
Moreover ASPM Control bits in Link Control register are controlled by pcie/aspm.c code which sets it according to system ASPM settings, immediately after aardvark driver probes. So setting these bits by aardvark driver has no long running effect.
Remove code which touches ASPM L0s bits from this driver and let kernel's ASPM implementation to set ASPM state properly.
Some users are reporting issues that this code is problematic for some Intel wifi cards and removing it fixes them, see e.g.:
https://bugzilla.kernel.org/show_bug.cgi?id=196339
If problems with Intel wifi cards occur even after this commit, then pcie/aspm.c code could be modified / hooked to not enable ASPM L0s state for affected problematic cards.
--- drivers/pci/controller/pci-aardvark.c | 4 ---- 1 file changed, 4 deletions(-)
drivers/pci/controller/pci-aardvark.c +0 -4
@@ -321,10 +321,6 @@ static void advk_pcie_setup_hw(struct advk_pcie *pcie)advk_pcie_wait_for_link (pcie); - reg =PCIE_CORE_LINK_L0S_ENTRY | - (1 <<PCIE_CORE_LINK_WIDTH_SHIFT ); -advk_writel (pcie, reg,PCIE_CORE_LINK_CTRL_STAT_REG ); - reg =advk_readl (pcie,PCIE_CORE_CMD_STATUS_REG ); reg |=PCIE_CORE_CMD_MEM_ACCESS_EN | PCIE_CORE_CMD_IO_ACCESS_EN |
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Sasha Levin
maintainerPATCH 27/172 ps3disk: use the default segment boundary
In reply to Sasha LevinFrom: Emmanuel Nicolet <[email protected]>
[ Upstream commit 720bc316690bd27dea9d71510b50f0cd698ffc32 ]
Since commit dcebd755926b ("block: use bio_for_each_bvec() to compute multi-page bvec count"), the kernel will bug_on on the PS3 because bio_split() is called with sectors == 0:
kernel BUG at block/bio.c:1853!
Oops: Exception in kernel mode, sig: 5 [#1] BE PAGE_SIZE=4K MMU=Hash PREEMPT SMP NR_CPUS=8 NUMA PS3 Modules linked in: firewire_sbp2 rtc_ps3(+) soundcore ps3_gelic(+) \ ps3rom(+) firewire_core ps3vram(+) usb_common crc_itu_t CPU: 0 PID: 97 Comm: blkid Not tainted 5.3.0-rc4 #1 NIP: c00000000027d0d0 LR: c00000000027d0b0 CTR: 0000000000000000 REGS: c00000000135ae90 TRAP: 0700 Not tainted (5.3.0-rc4) MSR: 8000000000028032 <SF,EE,IR,DR,RI> CR: 44008240 XER: 20000000 IRQMASK: 0 GPR00: c000000000289368 c00000000135b120 c00000000084a500 c000000004ff8300 GPR04: 0000000000000c00 c000000004c905e0 c000000004c905e0 000000000000ffff GPR08: 0000000000000000 0000000000000001 0000000000000000 000000000000ffff GPR12: 0000000000000000 c0000000008ef000 000000000000003e 0000000000080001 GPR16: 0000000000000100 000000000000ffff 0000000000000000 0000000000000004 GPR20: c00000000062fd7e 0000000000000001 000000000000ffff 0000000000000080 GPR24: c000000000781788 c00000000135b350 0000000000000080 c000000004c905e0 GPR28: c00000000135b348 c000000004ff8300 0000000000000000 c000000004c90000 NIP [c00000000027d0d0] .bio_split+0x28/0xac LR [c00000000027d0b0] .bio_split+0x8/0xac Call Trace: [c00000000135b120] [c00000000027d130] .bio_split+0x88/0xac (unreliable) [c00000000135b1b0] [c000000000289368] .__blk_queue_split+0x11c/0x53c [c00000000135b2d0] [c00000000028f614] .blk_mq_make_request+0x80/0x7d4 [c00000000135b3d0] [c000000000283a8c] .generic_make_request+0x118/0x294 [c00000000135b4b0] [c000000000283d34] .submit_bio+0x12c/0x174 [c00000000135b580] [c000000000205a44] .mpage_bio_submit+0x3c/0x4c [c00000000135b600] [c000000000206184] .mpage_readpages+0xa4/0x184 [c00000000135b750] [c0000000001ff8fc] .blkdev_readpages+0x24/0x38 [c00000000135b7c0] [c0000000001589f0] .read_pages+0x6c/0x1a8 [c00000000135b8b0] [c000000000158c74] .__do_page_cache_readahead+0x118/0x184 [c00000000135b9b0] [c0000000001591a8] .force_page_cache_readahead+0xe4/0xe8 [c00000000135ba50] [c00000000014fc24] .generic_file_read_iter+0x1d8/0x830 [c00000000135bb50] [c0000000001ffadc] .blkdev_read_iter+0x40/0x5c [c00000000135bbc0] [c0000000001b9e00] .new_sync_read+0x144/0x1a0 [c00000000135bcd0] [c0000000001bc454] .vfs_read+0xa0/0x124 [c00000000135bd70] [c0000000001bc7a4] .ksys_read+0x70/0xd8 [c00000000135be20] [c00000000000a524] system_call+0x5c/0x70 Instruction dump: 7fe3fb78 482e30dc 7c0802a6 482e3085 7c9e2378 f821ff71 7ca42b78 7d3e00d0 7c7d1b78 79290fe0 7cc53378 69290001 <0b090000> 81230028 7bca0020 7929ba62 [ end trace 313fec760f30aa1f ]---
The problem originates from setting the segment boundary of the request queue to -1UL. This makes get_max_segment_size() return zero when offset is zero, whatever the max segment size. The test with BLK_SEG_BOUNDARY_MASK fails and 'mask - (mask & offset) + 1' overflows to zero in the return statement.
Not setting the segment boundary and using the default value (BLK_SEG_BOUNDARY_MASK) fixes the problem.
--- drivers/block/ps3disk.c | 1 - 1 file changed, 1 deletion(-)
drivers/block/ps3disk.c +0 -1
@@ -466,7 +466,6 @@ static int ps3disk_probe(struct ps3_system_bus_device *_dev) queue->queuedata = dev;blk_queue_max_hw_sectors (queue, dev->bounce_size >>9 ); -blk_queue_segment_boundary (queue,-1UL );blk_queue_dma_alignment (queue, dev->blk_size-1 );blk_queue_logical_block_size (queue, dev->blk_size);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 28/172 vfio/pci: fix memory leaks in alloc_perm_bits()
In reply to Sasha LevinFrom: Qian Cai <[email protected]>
[ Upstream commit 3e63b94b6274324ff2e7d8615df31586de827c4e ]
vfio_pci_disable() calls vfio_config_free() but forgets to call free_perm_bits() resulting in memory leaks,
unreferenced object 0xc000000c4db2dee0 (size 16):
comm "qemu-kvm", pid 4305, jiffies 4295020272 (age 3463.780s) hex dump (first 16 bytes):
00 00 ff 00 ff ff ff ff ff ff ff ff ff ff 00 00 ................
backtrace:
[<00000000a6a4552d>] alloc_perm_bits+0x58/0xe0 [vfio_pci]
[<00000000ac990549>] vfio_config_init+0xdf0/0x11b0 [vfio_pci]
init_pci_cap_msi_perm at drivers/vfio/pci/vfio_pci_config.c:1125
(inlined by) vfio_msi_cap_len at drivers/vfio/pci/vfio_pci_config.c:1180
(inlined by) vfio_cap_len at drivers/vfio/pci/vfio_pci_config.c:1241
(inlined by) vfio_cap_init at drivers/vfio/pci/vfio_pci_config.c:1468
(inlined by) vfio_config_init at drivers/vfio/pci/vfio_pci_config.c:1707
[<000000006db873a1>] vfio_pci_open+0x234/0x700 [vfio_pci]
[<00000000630e1906>] vfio_group_fops_unl_ioctl+0x8e0/0xb84 [vfio]
[<000000009e34c54f>] ksys_ioctl+0xd8/0x130
[<000000006577923d>] sys_ioctl+0x28/0x40
[<000000006d7b1cf2>] system_call_exception+0x114/0x1e0
[<0000000008ea7dd5>] system_call_common+0xf0/0x278
unreferenced object 0xc000000c4db2e330 (size 16):
comm "qemu-kvm", pid 4305, jiffies 4295020272 (age 3463.780s)
hex dump (first 16 bytes):
00 ff ff 00 ff ff ff ff ff ff ff ff ff ff 00 00 ................
backtrace:
[<000000004c71914f>] alloc_perm_bits+0x44/0xe0 [vfio_pci]
[<00000000ac990549>] vfio_config_init+0xdf0/0x11b0 [vfio_pci]
[<000000006db873a1>] vfio_pci_open+0x234/0x700 [vfio_pci]
[<00000000630e1906>] vfio_group_fops_unl_ioctl+0x8e0/0xb84 [vfio]
[<000000009e34c54f>] ksys_ioctl+0xd8/0x130
[<000000006577923d>] sys_ioctl+0x28/0x40
[<000000006d7b1cf2>] system_call_exception+0x114/0x1e0
[<0000000008ea7dd5>] system_call_common+0xf0/0x278--- drivers/vfio/pci/vfio_pci_config.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/vfio/pci/vfio_pci_config.c +5 -2
@@ -1732,8 +1732,11 @@ void vfio_config_free(struct vfio_pci_device *vdev) vdev->vconfig =NULL ;kfree (vdev->pci_config_map); vdev->pci_config_map =NULL ; -kfree (vdev->msi_perm); - vdev->msi_perm =NULL ; +if (vdev->msi_perm) { +free_perm_bits (vdev->msi_perm); +kfree (vdev->msi_perm); + vdev->msi_perm =NULL ; + } }/*
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 29/172 RDMA/mlx5: Add init2init as a modify command
In reply to Sasha LevinFrom: Aharon Landau <[email protected]>
[ Upstream commit 819f7427bafd494ef7ca4942ec6322db20722d7b ]
Missing INIT2INIT entry in the list of modify commands caused DEVX applications to be unable to modify_qp for this transition state. Add the MLX5_CMD_OP_INIT2INIT_QP opcode to the list of allowed DEVX opcodes.
--- drivers/infiniband/hw/mlx5/devx.c | 1 + 1 file changed, 1 insertion(+)
drivers/infiniband/hw/mlx5/devx.c +1 -0
@@ -328,6 +328,7 @@ static bool devx_is_obj_modify_cmd(const void *in)case MLX5_CMD_OP_SET_L2_TABLE_ENTRY :case MLX5_CMD_OP_RST2INIT_QP :case MLX5_CMD_OP_INIT2RTR_QP : +case MLX5_CMD_OP_INIT2INIT_QP :case MLX5_CMD_OP_RTR2RTS_QP :case MLX5_CMD_OP_RTS2RTS_QP :case MLX5_CMD_OP_SQERR2RTS_QP :
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 30/172 m68k/PCI: Fix a memory leak in an error handling path
In reply to Sasha LevinFrom: Christophe JAILLET <[email protected]>
[ Upstream commit c3f4ec050f56eeab7c1f290321f9b762c95bd332 ]
If 'ioremap' fails, we must free 'bridge', as done in other error handling path bellow.
--- arch/m68k/coldfire/pci.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
arch/m68k/coldfire/pci.c +3 -1
@@ -216,8 +216,10 @@ static int __init mcf_pci_init(void)/* Keep a virtual mapping to IO/config space active */ iospace = (unsigned long )ioremap (PCI_IO_PA ,PCI_IO_SIZE ); -if (iospace ==0 ) +if (iospace ==0 ) { +pci_free_host_bridge (bridge);return -ENODEV ; + }pr_info ("Coldfire: PCI IO/config window mapped to 0x%x\n" , (u32 ) iospace);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 31/172 gpio: dwapb: Call acpi_gpiochip_free_interrupts() on GPIO chip de-registration
In reply to Sasha LevinFrom: Andy Shevchenko <[email protected]>
[ Upstream commit 494a94e38dcf62543a32a4424d646ff80b4b28bd ]
Add missed acpi_gpiochip_free_interrupts() call when unregistering ports.
While at it, drop extra check to call acpi_gpiochip_request_interrupts(). There is no need to have an additional check to call acpi_gpiochip_request_interrupts(). Even without any interrupts available the registered ACPI Event handlers can be useful for debugging purposes.
--- drivers/gpio/gpio-dwapb.c | 25 ++++++++++++++++--------- 1 file changed, 16 insertions(+), 9 deletions(-)
drivers/gpio/gpio-dwapb.c +16 -9
@@ -535,26 +535,33 @@ static int dwapb_gpio_add_port(struct dwapb_gpio *gpio,dwapb_configure_irqs (gpio, port, pp); err =gpiochip_add_data (&port->gc, port); -if (err) +if (err) {dev_err (gpio->dev,"failed to register gpiochip for port%d\n" , port->idx); -else - port->is_registered = true; +return err; + }/* Add GPIO-signaled ACPI event support */ -if (pp->has_irq) -acpi_gpiochip_request_interrupts (&port->gc); +acpi_gpiochip_request_interrupts (&port->gc); -return err; + port->is_registered = true; + +return 0 ; }static void dwapb_gpio_unregister (struct dwapb_gpio *gpio) {unsigned int m; -for (m =0 ; m < gpio->nr_ports; ++m) -if (gpio->ports[m].is_registered) -gpiochip_remove (&gpio->ports[m].gc); +for (m =0 ; m < gpio->nr_ports; ++m) { +struct dwapb_gpio_port *port = &gpio->ports[m]; + +if (!port->is_registered) +continue ; + +acpi_gpiochip_free_interrupts (&port->gc); +gpiochip_remove (&port->gc); + } } static struct dwapb_platform_data *
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 32/172 mfd: wm8994: Fix driver operation if loaded as modules
In reply to Sasha LevinFrom: Marek Szyprowski <[email protected]>
[ Upstream commit d4f9b5428b53dd67f49ee8deed8d4366ed6b1933 ]
WM8994 chip has built-in regulators, which might be used for chip operation. They are controlled by a separate wm8994-regulator driver, which should be loaded before this driver calls regulator_get(), because that driver also provides consumer-supply mapping for the them. If that driver is not yet loaded, regulator core substitute them with dummy regulator, what breaks chip operation, because the built-in regulators are never enabled. Fix this by annotating this driver with MODULE_SOFTDEP() "pre" dependency to "wm8994_regulator" module.
--- drivers/mfd/wm8994-core.c | 1 + 1 file changed, 1 insertion(+)
drivers/mfd/wm8994-core.c +1 -0
@@ -704,3 +704,4 @@ module_i2c_driver(wm8994_i2c_driver);MODULE_DESCRIPTION ("Core support for the WM8994 audio CODEC" );MODULE_LICENSE ("GPL" );MODULE_AUTHOR ("Mark Brown <[email protected]>" ); +MODULE_SOFTDEP ("pre: wm8994_regulator" );
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 33/172 scsi: lpfc: Fix lpfc_nodelist leak when processing unsolicited event
In reply to Sasha LevinFrom: Xiyu Yang <[email protected]>
[ Upstream commit 7217e6e694da3aae6d17db8a7f7460c8d4817ebf ]
In order to create or activate a new node, lpfc_els_unsol_buffer() invokes lpfc_nlp_init() or lpfc_enable_node() or lpfc_nlp_get(), all of them will return a reference of the specified lpfc_nodelist object to "ndlp" with increased refcnt.
When lpfc_els_unsol_buffer() returns, local variable "ndlp" becomes invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of lpfc_els_unsol_buffer(). When "ndlp" in DEV_LOSS, the function forgets to decrease the refcnt increased by lpfc_nlp_init() or lpfc_enable_node() or lpfc_nlp_get(), causing a refcnt leak.
Fix this issue by calling lpfc_nlp_put() when "ndlp" in DEV_LOSS.
--- drivers/scsi/lpfc/lpfc_els.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/scsi/lpfc/lpfc_els.c +2 -0
@@ -7949,6 +7949,8 @@ lpfc_els_unsol_buffer(struct lpfc_hba *phba, struct lpfc_sli_ring *pring,spin_lock_irq (shost->host_lock);if (ndlp->nlp_flag &NLP_IN_DEV_LOSS ) {spin_unlock_irq (shost->host_lock); +if (newnode) +lpfc_nlp_put (ndlp); goto dropit; }spin_unlock_irq (shost->host_lock);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 34/172 clk: clk-flexgen: fix clock-critical handling
In reply to Sasha LevinFrom: Alain Volmat <[email protected]>
[ Upstream commit a403bbab1a73d798728d76931cab3ff0399b9560 ]
Fixes an issue leading to having all clocks following a critical clocks marked as well as criticals.
--- drivers/clk/st/clk-flexgen.c | 1 + 1 file changed, 1 insertion(+)
drivers/clk/st/clk-flexgen.c +1 -0
@@ -373,6 +373,7 @@ static void __init st_of_flexgen_setup(struct device_node *np)break ; } + flex_flags &= ~CLK_IS_CRITICAL ;of_clk_detect_critical (np, i, &flex_flags);/*
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 35/172 powerpc/perf/hv-24x7: Fix inconsistent output values incase multiple hv-24x7 events run
In reply to Sasha LevinFrom: Kajol Jain <[email protected]>
[ Upstream commit b4ac18eead28611ff470d0f47a35c4e0ac080d9c ]
Commit 2b206ee6b0df ("powerpc/perf/hv-24x7: Display change in counter values")' added to print _change_ in the counter value rather then raw value for 24x7 counters. Incase of transactions, the event count is set to 0 at the beginning of the transaction. It also sets the event's prev_count to the raw value at the time of initialization. Because of setting event count to 0, we are seeing some weird behaviour, whenever we run multiple 24x7 events at a time.
For example:
command#: ./perf stat -e "{hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=0/,
hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=1/}"
-C 0 -I 1000 sleep 100
1.000121704 120 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=0/
1.000121704 5 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=1/
2.000357733 8 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=0/
2.000357733 10 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=1/
3.000495215 18,446,744,073,709,551,616 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=0/
3.000495215 18,446,744,073,709,551,616 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=1/
4.000641884 56 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=0/
4.000641884 18,446,744,073,709,551,616 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=1/
5.000791887 18,446,744,073,709,551,616 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=0/Getting these large values in case we do -I.
As we are setting event_count to 0, for interval case, overall event_count is not coming in incremental order. As we may can get new delta lesser then previous count. Because of which when we print intervals, we are getting negative value which create these large values.
This patch removes part where we set event_count to 0 in function 'h_24x7_event_read'. There won't be much impact as we do set event->hw.prev_count to the raw value at the time of initialization to print change value.
With this patch
In power9 platform
command#: ./perf stat -e "{hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=0/,
hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=1/}"
-C 0 -I 1000 sleep 100
1.000117685 93 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=0/
1.000117685 1 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=1/
2.000349331 98 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=0/
2.000349331 2 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=1/
3.000495900 131 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=0/
3.000495900 4 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=1/
4.000645920 204 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=0/
4.000645920 61 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=1/
4.284169997 22 hv_24x7/PM_MCS01_128B_RD_DISP_PORT01,chip=0/--- arch/powerpc/perf/hv-24x7.c | 10 ---------- 1 file changed, 10 deletions(-)
arch/powerpc/perf/hv-24x7.c +0 -10
@@ -1413,16 +1413,6 @@ static void h_24x7_event_read(struct perf_event *event) h24x7hw = &get_cpu_var (hv_24x7_hw); h24x7hw->events[i] = event;put_cpu_var (h24x7hw); -/* -* Clear the event count so we can compute the _change_ -* in the 24x7 raw counter value at the end of the txn. -* -* Note that we could alternatively read the 24x7 value -* now and save its value in event->hw.prev_count. But -* that would require issuing a hcall, which would then -* defeat the purpose of using the txn interface. -*/ -local64_set (&event->count,0 ); }put_cpu_var (hv_24x7_reqb);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 36/172 nfsd: Fix svc_xprt refcnt leak when setup callback client failed
In reply to Sasha LevinFrom: Xiyu Yang <[email protected]>
[ Upstream commit a4abc6b12eb1f7a533c2e7484cfa555454ff0977 ]
nfsd4_process_cb_update() invokes svc_xprt_get(), which increases the refcount of the "c->cn_xprt".
The reference counting issue happens in one exception handling path of nfsd4_process_cb_update(). When setup callback client failed, the function forgets to decrease the refcnt increased by svc_xprt_get(), causing a refcnt leak.
Fix this issue by calling svc_xprt_put() when setup callback client failed.
--- fs/nfsd/nfs4callback.c | 2 ++ 1 file changed, 2 insertions(+)
fs/nfsd/nfs4callback.c +2 -0
@@ -1149,6 +1149,8 @@ static void nfsd4_process_cb_update(struct nfsd4_callback *cb) err =setup_callback_client (clp, &conn, ses);if (err) {nfsd4_mark_cb_down (clp, err); +if (c) +svc_xprt_put (c->cn_xprt);return ; } }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 37/172 PCI: vmd: Filter resource type bits from shadow register
In reply to Sasha LevinFrom: Jon Derrick <[email protected]>
[ Upstream commit 3e5095eebe015d5a4d566aa5e03c8621add5f0a7 ]
Versions of VMD with the Host Physical Address shadow register use this register to calculate the bus address offset needed to do guest passthrough of the domain. This register shadows the Host Physical Address registers including the resource type bits. After calculating the offset, the extra resource type bits lead to the VMD resources being over-provisioned at the front and under-provisioned at the back.
Example:
pci 10000:80:02.0: reg 0x10: [mem 0xf801fffc-0xf803fffb 64bit]
Expected:
pci 10000:80:02.0: reg 0x10: [mem 0xf8020000-0xf803ffff 64bit]
If other devices are mapped in the over-provisioned front, it could lead to resource conflict issues with VMD or those devices.
--- drivers/pci/controller/vmd.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/pci/controller/vmd.c +4 -2
@@ -617,9 +617,11 @@ static int vmd_enable_domain(struct vmd_dev *vmd, unsigned long features)if (!membar2)return -ENOMEM ; offset[0 ] = vmd->dev->resource[VMD_MEMBAR1 ].start - -readq (membar2 +MB2_SHADOW_OFFSET ); + (readq (membar2 +MB2_SHADOW_OFFSET ) & +PCI_BASE_ADDRESS_MEM_MASK ); offset[1 ] = vmd->dev->resource[VMD_MEMBAR2 ].start - -readq (membar2 +MB2_SHADOW_OFFSET +8 ); + (readq (membar2 +MB2_SHADOW_OFFSET +8 ) & +PCI_BASE_ADDRESS_MEM_MASK );pci_iounmap (vmd->dev, membar2); } }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 38/172 powerpc/crashkernel: Take "mem=" option into account
In reply to Sasha LevinFrom: Pingfan Liu <[email protected]>
[ Upstream commit be5470e0c285a68dc3afdea965032f5ddc8269d7 ]
'mem=" option is an easy way to put high pressure on memory during some test. Hence after applying the memory limit, instead of total mem, the actual usable memory should be considered when reserving mem for crashkernel. Otherwise the boot up may experience OOM issue.
E.g. it would reserve 4G prior to the change and 512M afterward, if passing crashkernel="2G-4G:384M,4G-16G:512M,16G-64G:1G,64G-128G:2G,128G-:4G", and mem=5G on a 256G machine.
This issue is powerpc specific because it puts higher priority on fadump and kdump reservation than on "mem=". Referring the following code:
if (fadump_reserve_mem() == 0)
reserve_crashkernel();
...
/* Ensure that total memory size is page-aligned. */
limit = ALIGN(memory_limit ?: memblock_phys_mem_size(), PAGE_SIZE);
memblock_enforce_memory_limit(limit);While on other arches, the effect of "mem=" takes a higher priority and pass through memblock_phys_mem_size() before calling reserve_crashkernel().
--- arch/powerpc/kernel/machine_kexec.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-)
arch/powerpc/kernel/machine_kexec.c +5 -3
@@ -116,11 +116,12 @@ void machine_kexec(struct kimage *image)void __init reserve_crashkernel (void ) { -unsigned long long crash_size, crash_base; +unsigned long long crash_size, crash_base, total_mem_sz;int ret; + total_mem_sz = memory_limit ? memory_limit :memblock_phys_mem_size ();/* use common parsing */ - ret =parse_crashkernel (boot_command_line,memblock_phys_mem_size (), + ret =parse_crashkernel (boot_command_line, total_mem_sz, &crash_size, &crash_base);if (ret ==0 && crash_size >0 ) { crashk_res.start = crash_base;
@@ -179,6 +180,7 @@ void __init reserve_crashkernel(void)/* Crash kernel trumps memory limit */ if (memory_limit && memory_limit <= crashk_res.end) { memory_limit = crashk_res.end +1 ; + total_mem_sz = memory_limit;printk ("Adjusted memory limit for crashkernel, now 0x%llx\n" , memory_limit); }
@@ -187,7 +189,7 @@ void __init reserve_crashkernel(void)"for crashkernel (System RAM: %ldMB)\n" , (unsigned long )(crash_size >>20 ), (unsigned long )(crashk_res.start >>20 ), - (unsigned long)(memblock_phys_mem_size() >> 20)); + (unsigned long)(total_mem_sz >> 20));if (!memblock_is_region_memory (crashk_res.start, crash_size) ||memblock_reserve (crashk_res.start, crash_size)) {
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 39/172 pwm: img: Call pm_runtime_put() in pm_runtime_get_sync() failed case
In reply to Sasha LevinFrom: Navid Emamdoost <[email protected]>
[ Upstream commit ca162ce98110b98e7d97b7157328d34dcfdd40a9 ]
Even in failed case of pm_runtime_get_sync(), the usage_count is incremented. In order to keep the usage_count with correct value call appropriate pm_runtime_put().
--- drivers/pwm/pwm-img.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)
drivers/pwm/pwm-img.c +6 -2
@@ -132,8 +132,10 @@ static int img_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm, duty =DIV_ROUND_UP (timebase * duty_ns, period_ns); ret =pm_runtime_get_sync (chip->dev); -if (ret <0 ) +if (ret <0 ) { +pm_runtime_put_autosuspend (chip->dev);return ret; + } val =img_pwm_readl (pwm_chip,PWM_CTRL_CFG ); val &= ~(PWM_CTRL_CFG_DIV_MASK <<PWM_CTRL_CFG_DIV_SHIFT (pwm->hwpwm));
@@ -334,8 +336,10 @@ static int img_pwm_remove(struct platform_device *pdev)int ret; ret =pm_runtime_get_sync (&pdev->dev); -if (ret <0 ) +if (ret <0 ) { +pm_runtime_put (&pdev->dev);return ret; + }for (i =0 ; i < pwm_chip->chip.npwm; i++) { val =img_pwm_readl (pwm_chip,PWM_CTRL_CFG );
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 40/172 yam: fix possible memory leak in yam_init_driver
In reply to Sasha LevinFrom: Wang Hai <[email protected]>
[ Upstream commit 98749b7188affbf2900c2aab704a8853901d1139 ]
If register_netdev(dev) fails, free_netdev(dev) needs to be called, otherwise a memory leak will occur.
--- drivers/net/hamradio/yam.c | 1 + 1 file changed, 1 insertion(+)
drivers/net/hamradio/yam.c +1 -0
@@ -1148,6 +1148,7 @@ static int __init yam_init_driver(void) err =register_netdev (dev);if (err) {printk (KERN_WARNING "yam: cannot register net device %s\n" , dev->name); +free_netdev (dev); goto error; } yam_devs[i] = dev;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 41/172 fat: don't allow to mount if the FAT length == 0
In reply to Sasha LevinFrom: OGAWA Hirofumi <[email protected]>
[ Upstream commit b1b65750b8db67834482f758fc385bfa7560d228 ]
If FAT length == 0, the image doesn't have any data. And it can be the cause of overlapping the root dir and FAT entries.
Also Windows treats it as invalid format.
--- fs/fat/inode.c | 6 ++++++ 1 file changed, 6 insertions(+)
fs/fat/inode.c +6 -0
@@ -1519,6 +1519,12 @@ static int fat_read_bpb(struct super_block *sb, struct fat_boot_sector *b, goto out; } +if (bpb->fat_fat_length ==0 && bpb->fat32_length ==0 ) { +if (!silent) +fat_msg (sb,KERN_ERR ,"bogus number of FAT sectors" ); + goto out; + } + error =0 ; out:
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 42/172 NTB: ntb_pingpong: Choose doorbells based on port number
In reply to Sasha LevinFrom: Logan Gunthorpe <[email protected]>
[ Upstream commit ca93c45755da98302c93abdd788fc09113baf9e0 ]
This commit fixes pingpong support for existing drivers that do not implement ntb_default_port_number() and ntb_default_peer_port_number(). This is required for hardware (like the crosslink topology of switchtec) which cannot assign reasonable port numbers to each port due to its perfect symmetry.
Instead of picking the doorbell to use based on the the index of the peer, we use the peer's port number. This is a bit clearer and easier to understand.
--- drivers/ntb/test/ntb_pingpong.c | 14 ++++++-------- 1 file changed, 6 insertions(+), 8 deletions(-)
drivers/ntb/test/ntb_pingpong.c +6 -8
@@ -121,15 +121,14 @@ static int pp_find_next_peer(struct pp_ctx *pp) link =ntb_link_is_up (pp->ntb,NULL ,NULL );/* Find next available peer */ -if (link & pp->nmask) { +if (link & pp->nmask) pidx =__ffs64 (link & pp->nmask); - out_db =BIT_ULL (pidx +1 ); - }else if (link & pp->pmask) { +else if (link & pp->pmask) pidx =__ffs64 (link & pp->pmask); - out_db =BIT_ULL (pidx); - }else { +else return -ENODEV ; - } + + out_db =BIT_ULL (ntb_peer_port_number (pp->ntb, pidx));spin_lock (&pp->lock); pp->out_pidx = pidx;
@@ -303,7 +302,7 @@ static void pp_init_flds(struct pp_ctx *pp)break ; } - pp->in_db =BIT_ULL (pidx); + pp->in_db =BIT_ULL (lport); pp->pmask =GENMASK_ULL (pidx,0 ) >>1 ; pp->nmask =GENMASK_ULL (pcnt -1 , pidx);
@@ -435,4 +434,3 @@ static void __exit pp_exit(void)debugfs_remove_recursive (pp_dbgfs_topdir); }module_exit (pp_exit); -
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 43/172 NTB: Fix the default port and peer numbers for legacy drivers
In reply to Sasha LevinFrom: Logan Gunthorpe <[email protected]>
[ Upstream commit fc8b086d9dbd57458d136c4fa70ee26f832c3a2e ]
When the commit adding ntb_default_port_number() and ntb_default_peer_port_number() entered the kernel there was no users of it so it was impossible to tell what the API needed.
When a user finally landed a year later (ntb_pingpong) there were more NTB topologies were created and no consideration was considered to how other drivers had changed.
Now that there is a user it can be fixed to provide a sensible default for the legacy drivers that do not implement ntb_{peer_}port_number(). Seeing ntb_pingpong doesn't check error codes returning EINVAL was also not sensible.
Patches for ntb_pingpong and ntb_perf follow (which are broken otherwise) to support hardware that doesn't have port numbers. This is important not only to not break support with existing drivers but for the cross link topology which, due to its perfect symmetry, cannot assign unique port numbers to each side.
--- drivers/ntb/ntb.c | 8 ++------ 1 file changed, 2 insertions(+), 6 deletions(-)
drivers/ntb/ntb.c +2 -6
@@ -214,10 +214,8 @@ int ntb_default_port_number(struct ntb_dev *ntb)case NTB_TOPO_B2B_DSD :return NTB_PORT_SEC_DSD ;default : -break ; +return 0 ; } - -return -EINVAL ; }EXPORT_SYMBOL (ntb_default_port_number);
@@ -240,10 +238,8 @@ int ntb_default_peer_port_number(struct ntb_dev *ntb, int pidx)case NTB_TOPO_B2B_DSD :return NTB_PORT_PRI_USD ;default : -break ; +return 0 ; } - -return -EINVAL ; }EXPORT_SYMBOL (ntb_default_peer_port_number);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 44/172 mksysmap: Fix the mismatch of '.L' symbols in System.map
In reply to Sasha LevinFrom: ashimida <[email protected]>
[ Upstream commit 72d24accf02add25e08733f0ecc93cf10fcbd88c ]
When System.map was generated, the kernel used mksysmap to filter the kernel symbols, but all the symbols with the second letter 'L' in the kernel were filtered out, not just the symbols starting with 'dot + L'.
For example:
ashimida@ubuntu:~/linux$ cat System.map |grep ' .L' ashimida@ubuntu:~/linux$ nm -n vmlinux |grep ' .L' ffff0000088028e0 t bLength_show ...... ffff0000092e0408 b PLLP_OUTC_lock ffff0000092e0410 b PLLP_OUTA_lock
The original intent should be to filter out all local symbols starting with '.L', so the dot should be escaped.
--- scripts/mksysmap | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
scripts/mksysmap +1 -1
@@ -41,4 +41,4 @@ # so we just ignore them to let readprofile continue to work. # (At least sparc64 has __crc_ in the middle). -$NM -n $1 | grep -v '\( [aNUw] \)\|\(__crc_\)\|\( \$[adt]\)\|\( .L\)' > $2 +$NM -n $1 | grep -v '\( [aNUw] \)\|\(__crc_\)\|\( \$[adt]\)\|\( \.L\)' > $2
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 45/172 apparmor: fix introspection of of task mode for unconfined tasks
In reply to Sasha LevinFrom: John Johansen <[email protected]>
[ Upstream commit dd2569fbb053719f7df7ef8fdbb45cf47156a701 ]
Fix two issues with introspecting the task mode.
1. If a task is attached to a unconfined profile that is not the ns->unconfined profile then. Mode the mode is always reported as -
$ ps -Z
LABEL PID TTY TIME CMD
unconfined 1287 pts/0 00:00:01 bash
test (-) 1892 pts/0 00:00:00 psinstead of the correct value of (unconfined) as shown below
$ ps -Z
LABEL PID TTY TIME CMD
unconfined 2483 pts/0 00:00:01 bash
test (unconfined) 3591 pts/0 00:00:00 ps2. if a task is confined by a stack of profiles that are unconfined the output of label mode is again the incorrect value of (-) like above, instead of (unconfined). This is because the visibile profile count increment is skipped by the special casing of unconfined.
--- security/apparmor/label.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
security/apparmor/label.c +2 -2
@@ -1535,13 +1535,13 @@ static const char *label_modename(struct aa_ns *ns, struct aa_label *label,label_for_each (i, label, profile) {if (aa_ns_visible (ns, profile->ns, flags &FLAG_VIEW_SUBNS )) { -if (profile->mode ==APPARMOR_UNCONFINED ) + count++; +if (profile == profile->ns->unconfined)/* special case unconfined so stacks with * unconfined don't report as mixed. ie. * profile_foo//&:ns1:unconfined (mixed) */ continue ; - count++;if (mode ==-1 ) mode = profile->mode;else if (mode != profile->mode)
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 46/172 apparmor: check/put label on apparmor_sk_clone_security()
In reply to Sasha LevinFrom: Mauricio Faria de Oliveira <[email protected]>
[ Upstream commit 3b646abc5bc6c0df649daea4c2c976bd4d47e4c8 ]
Currently apparmor_sk_clone_security() does not check for existing label/peer in the 'new' struct sock; it just overwrites it, if any (with another reference to the label of the source sock.)
static void apparmor_sk_clone_security(const struct sock *sk,
struct sock *newsk)
{
struct aa_sk_ctx *ctx = SK_CTX(sk);
struct aa_sk_ctx *new = SK_CTX(newsk);
new->label = aa_get_label(ctx->label);
new->peer = aa_get_label(ctx->peer);
}This might leak label references, which might overflow under load. Thus, check for and put labels, to prevent such errors.
Note this is similarly done on:
static int apparmor_socket_post_create(struct socket *sock, ...)
...
if (sock->sk) {
struct aa_sk_ctx *ctx = SK_CTX(sock->sk);
aa_put_label(ctx->label);
ctx->label = aa_get_label(label);
}
...Context:
-------
The label reference count leak is observed if apparmor_sock_graft() is called previously: this sets the 'ctx->label' field by getting a reference to the current label (later overwritten, without put.)
static void apparmor_sock_graft(struct sock *sk, ...)
{
struct aa_sk_ctx *ctx = SK_CTX(sk);
if (!ctx->label)
ctx->label = aa_get_current_label();
}And that is the case on crypto/af_alg.c:af_alg_accept():
int af_alg_accept(struct sock *sk, struct socket *newsock, ...)
...
struct sock *sk2;
...
sk2 = sk_alloc(...);
...
security_sock_graft(sk2, newsock);
security_sk_clone(sk, sk2);
...Apparently both calls are done on their own right, especially for other LSMs, being introduced in 2010/2014, before apparmor socket mediation in 2017 (see commits [1,2,3,4]).
So, it looks OK there! Let's fix the reference leak in apparmor.
Test-case:
---------
Exercise that code path enough to overflow label reference count.
$ cat aa-refcnt-af_alg.c
#include <stdio.h>
#include <string.h>
#include <unistd.h>
#include <sys/socket.h>
#include <linux/if_alg.h> int main() {
int sockfd;
struct sockaddr_alg sa;
/* Setup the crypto API socket */
sockfd = socket(AF_ALG, SOCK_SEQPACKET, 0);
if (sockfd < 0) {
perror("socket");
return 1;
}
memset(&sa, 0, sizeof(sa));
sa.salg_family = AF_ALG;
strcpy((char *) sa.salg_type, "rng");
strcpy((char *) sa.salg_name, "stdrng");
if (bind(sockfd, (struct sockaddr *) &sa, sizeof(sa)) < 0) {
perror("bind");
return 1;
}
/* Accept a "connection" and close it; repeat. */
while (!close(accept(sockfd, NULL, 0)));
return 0;
}
$ gcc -o aa-refcnt-af_alg aa-refcnt-af_alg.c
$ ./aa-refcnt-af_alg
<a few hours later>
[ 9928.475953] refcount_t overflow at apparmor_sk_clone_security+0x37/0x70 in aa-refcnt-af_alg[1322], uid/euid: 1000/1000
...
[ 9928.507443] RIP: 0010:apparmor_sk_clone_security+0x37/0x70
...
[ 9928.514286] security_sk_clone+0x33/0x50
[ 9928.514807] af_alg_accept+0x81/0x1c0 [af_alg]
[ 9928.516091] alg_accept+0x15/0x20 [af_alg]
[ 9928.516682] SYSC_accept4+0xff/0x210
[ 9928.519609] SyS_accept+0x10/0x20
[ 9928.520190] do_syscall_64+0x73/0x130
[ 9928.520808] entry_SYSCALL_64_after_hwframe+0x3d/0xa2Note that other messages may be seen, not just overflow, depending on the value being incremented by kref_get(); on another run:
[ 7273.182666] refcount_t: saturated; leaking memory.
...
[ 7273.185789] refcount_t: underflow; use-after-free.Kprobes:
-------
Using kprobe events to monitor sk -> sk_security -> label -> count (kref):
Original v5.7 (one reference leak every iteration)
... (af_alg_accept+0x0/0x1c0) label=0xffff8a0f36c25eb0 label_refcnt=0x11fd2 ... (af_alg_release_parent+0x0/0xd0) label=0xffff8a0f36c25eb0 label_refcnt=0x11fd4 ... (af_alg_accept+0x0/0x1c0) label=0xffff8a0f36c25eb0 label_refcnt=0x11fd3 ... (af_alg_release_parent+0x0/0xd0) label=0xffff8a0f36c25eb0 label_refcnt=0x11fd5 ... (af_alg_accept+0x0/0x1c0) label=0xffff8a0f36c25eb0 label_refcnt=0x11fd4 ... (af_alg_release_parent+0x0/0xd0) label=0xffff8a0f36c25eb0 label_refcnt=0x11fd6
Patched v5.7 (zero reference leak per iteration)
... (af_alg_accept+0x0/0x1c0) label=0xffff9ff376c25eb0 label_refcnt=0x593 ... (af_alg_release_parent+0x0/0xd0) label=0xffff9ff376c25eb0 label_refcnt=0x594 ... (af_alg_accept+0x0/0x1c0) label=0xffff9ff376c25eb0 label_refcnt=0x593 ... (af_alg_release_parent+0x0/0xd0) label=0xffff9ff376c25eb0 label_refcnt=0x594 ... (af_alg_accept+0x0/0x1c0) label=0xffff9ff376c25eb0 label_refcnt=0x593 ... (af_alg_release_parent+0x0/0xd0) label=0xffff9ff376c25eb0 label_refcnt=0x594
Commits:
-------
[1] commit 507cad355fc9 ("crypto: af_alg - Make sure sk_security is initialized on accept()ed sockets")
[2] commit 4c63f83c2c2e ("crypto: af_alg - properly label AF_ALG socket")
[3] commit 2acce6aa9f65 ("Networking") a.k.a ("crypto: af_alg - Avoid sock_graft call warning)
[4] commit 56974a6fcfef ("apparmor: add base infastructure for socket mediation")
--- security/apparmor/lsm.c | 5 +++++ 1 file changed, 5 insertions(+)
security/apparmor/lsm.c +5 -0
@@ -797,7 +797,12 @@ static void apparmor_sk_clone_security(const struct sock *sk,struct aa_sk_ctx *ctx =SK_CTX (sk);struct aa_sk_ctx *new =SK_CTX (newsk); +if (new->label) +aa_put_label (new->label); new->label =aa_get_label (ctx->label); + +if (new->peer) +aa_put_label (new->peer); new->peer =aa_get_label (ctx->peer); }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 47/172 ASoC: meson: add missing free_irq() in error path
In reply to Sasha LevinFrom: "Pavel Machek (CIP)" <[email protected]>
[ Upstream commit 3b8a299a58b2afce464ae11324b59dcf0f1d10a7 ]
free_irq() is missing in case of error, fix that.
--- sound/soc/meson/axg-fifo.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-)
sound/soc/meson/axg-fifo.c +8 -2
@@ -209,7 +209,7 @@ static int axg_fifo_pcm_open(struct snd_pcm_substream *ss)/* Enable pclk to access registers and clock the fifo ip */ ret =clk_prepare_enable (fifo->pclk);if (ret) -return ret; + goto free_irq;/* Setup status2 so it reports the memory pointer */ regmap_update_bits(fifo->map, FIFO_CTRL1,
@@ -229,8 +229,14 @@ static int axg_fifo_pcm_open(struct snd_pcm_substream *ss)/* Take memory arbitror out of reset */ ret =reset_control_deassert (fifo->arb);if (ret) -clk_disable_unprepare (fifo->pclk); + goto free_clk; + +return 0 ; +free_clk: +clk_disable_unprepare (fifo->pclk); +free_irq: +free_irq (fifo->irq, ss);return ret; }
Signature · 1 line
2.25.1
Re: [PATCH AUTOSEL 4.19 047/172] ASoC: meson: add missing free_irq() in error path
Hi!
Quoted 11 lines
From: "Pavel Machek (CIP)" <[email protected]>
[ Upstream commit
3b8a299a58b2afce464ae11324b59dcf0f1d10a7]
free_irq()is missing in case of error, fix that.Signed-off-by Pavel Machek (CIP) <[email protected]>Reviewed-by Jerome Brunet <[email protected]>
Notice that the bug this fixes is theoretical (found by code review) and the fix itself was not tested by me as I don't have the hardware.
It may be good idea to for mainline to test the change a bit...
Best regards,
Pavel
Signature · 2 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Sasha Levin
maintainerPATCH 48/172 scsi: sr: Fix sr_probe() missing deallocate of device minor
In reply to Sasha LevinFrom: Simon Arlott <[email protected]>
[ Upstream commit 6555781b3fdec5e94e6914511496144241df7dee ]
If the cdrom fails to be registered then the device minor should be deallocated.
--- drivers/scsi/sr.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/scsi/sr.c +5 -1
@@ -748,7 +748,7 @@ static int sr_probe(struct device *dev) cd->cdi.disk = disk;if (register_cdrom (&cd->cdi)) - goto fail_put; + goto fail_minor;/* * Initialize block layer runtime PM stuffs before the
@@ -766,6 +766,10 @@ static int sr_probe(struct device *dev)return 0 ; +fail_minor: +spin_lock (&sr_index_lock); +clear_bit (minor, sr_index_bits); +spin_unlock (&sr_index_lock); fail_put:put_disk (disk); fail_free:
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 49/172 scsi: ibmvscsi: Don't send host info in adapter info MAD after LPM
In reply to Sasha LevinFrom: Tyrel Datwyler <[email protected]>
[ Upstream commit 4919b33b63c8b69d8dcf2b867431d0e3b6dc6d28 ]
The adapter info MAD is used to send the client info and receive the host info as a response. A persistent buffer is used and as such the client info is overwritten after the response. During the course of a normal adapter reset the client info is refreshed in the buffer in preparation for sending the adapter info MAD.
However, in the special case of LPM where we reenable the CRQ instead of a full CRQ teardown and reset we fail to refresh the client info in the adapter info buffer. As a result, after Live Partition Migration (LPM) we erroneously report the host's info as our own.
[mkp: typos]
--- drivers/scsi/ibmvscsi/ibmvscsi.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/scsi/ibmvscsi/ibmvscsi.c +2 -0
@@ -429,6 +429,8 @@ static int ibmvscsi_reenable_crq_queue(struct crq_queue *queue,int rc =0 ;struct vio_dev *vdev =to_vio_dev (hostdata->dev); +set_adapter_info (hostdata); +/* Re-enable the CRQ */ do { if (rc)
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 50/172 apparmor: fix nnp subset test for unconfined
In reply to Sasha LevinFrom: John Johansen <[email protected]>
[ Upstream commit 3ed4aaa94fc07db3cd0c91be95e3e1b9782a2710 ]
The subset test is not taking into account the unconfined exception which will cause profile transitions in the stacked confinement case to fail when no_new_privs is applied.
This fixes a regression introduced in the fix for
https://bugs.launchpad.net/bugs/1839037
--- security/apparmor/domain.c | 9 +++++---- security/apparmor/include/label.h | 1 + security/apparmor/label.c | 33 +++++++++++++++++++++++++++++++ 3 files changed, 39 insertions(+), 4 deletions(-)
security/apparmor/domain.c +5 -4
@@ -939,7 +939,8 @@ int apparmor_bprm_set_creds(struct linux_binprm *bprm)* aways results in a further reduction of permissions. */ if ((bprm->unsafe &LSM_UNSAFE_NO_NEW_PRIVS ) && - !unconfined (label) && !aa_label_is_subset (new, ctx->nnp)) { + !unconfined (label) && + !aa_label_is_unconfined_subset (new, ctx->nnp)) { error = -EPERM ; info ="no new privs" ; goto audit;
@@ -1217,7 +1218,7 @@ int aa_change_hat(const char *hats[], int count, u64 token, int flags)* reduce restrictions. */ if (task_no_new_privs (current) && !unconfined (label) && - !aa_label_is_subset (new, ctx->nnp)) { + !aa_label_is_unconfined_subset (new, ctx->nnp)) {/* not an apparmor denial per se, so don't log it */ AA_DEBUG ("no_new_privs - change_hat denied" ); error = -EPERM ;
@@ -1238,7 +1239,7 @@ int aa_change_hat(const char *hats[], int count, u64 token, int flags)* reduce restrictions. */ if (task_no_new_privs (current) && !unconfined (label) && - !aa_label_is_subset (previous, ctx->nnp)) { + !aa_label_is_unconfined_subset (previous, ctx->nnp)) {/* not an apparmor denial per se, so don't log it */ AA_DEBUG ("no_new_privs - change_hat denied" ); error = -EPERM ;
@@ -1433,7 +1434,7 @@ int aa_change_profile(const char *fqname, int flags)* reduce restrictions. */ if (task_no_new_privs (current) && !unconfined (label) && - !aa_label_is_subset (new, ctx->nnp)) { + !aa_label_is_unconfined_subset (new, ctx->nnp)) {/* not an apparmor denial per se, so don't log it */ AA_DEBUG ("no_new_privs - change_hat denied" ); error = -EPERM ;
security/apparmor/include/label.h +1 -0
@@ -285,6 +285,7 @@ bool aa_label_init(struct aa_label *label, int size, gfp_t gfp);struct aa_label *aa_label_alloc (int size,struct aa_proxy *proxy,gfp_t gfp);bool aa_label_is_subset (struct aa_label *set,struct aa_label *sub); +bool aa_label_is_unconfined_subset (struct aa_label *set,struct aa_label *sub);struct aa_profile *__aa_label_next_not_in_set (struct label_it *I ,struct aa_label *set,struct aa_label *sub);
security/apparmor/label.c +33 -0
@@ -554,6 +554,39 @@ bool aa_label_is_subset(struct aa_label *set, struct aa_label *sub)return __aa_label_next_not_in_set (&i, set, sub) ==NULL ; } +/** +* aa_label_is_unconfined_subset - test if @sub is a subset of @set +* @set: label to test against +* @sub: label to test if is subset of @set +* +* This checks for subset but taking into account unconfined. IF +* @sub contains an unconfined profile that does not have a matching +* unconfined in @set then this will not cause the test to fail. +* Conversely we don't care about an unconfined in @set that is not in +* @sub +* +* Returns: true if @sub is special_subset of @set +* else false +*/ +bool aa_label_is_unconfined_subset (struct aa_label *set,struct aa_label *sub) +{ +struct label_it i = { }; +struct aa_profile *p; + +AA_BUG (!set); +AA_BUG (!sub); + +if (sub == set) +return true; + +do { + p =__aa_label_next_not_in_set (&i, set, sub); +if (p && !profile_unconfined (p)) +break ; + }while (p); + +return p ==NULL ; +}/**
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 51/172 x86/purgatory: Disable various profiling and sanitizing options
In reply to Sasha LevinFrom: Hans de Goede <[email protected]>
[ Upstream commit e2ac07c06058ae2d58b45bbf2a2a352771d76fcb ]
Since the purgatory is a special stand-alone binary, various profiling and sanitizing options must be disabled. Having these options enabled typically will cause dependencies on various special symbols exported by special libs / stubs used by these frameworks. Since the purgatory is special, it is not linked against these stubs causing missing symbols in the purgatory if these options are not disabled.
Sync the set of disabled profiling and sanitizing options with that from drivers/firmware/efi/libstub/Makefile, adding -DDISABLE_BRANCH_PROFILING to the CFLAGS and setting:
GCOV_PROFILE := n
UBSAN_SANITIZE := n
This fixes broken references to ftrace_likely_update() when CONFIG_TRACE_BRANCH_PROFILING is enabled and to __gcov_init() and __gcov_exit() when CONFIG_GCOV_KERNEL is enabled.
--- arch/x86/purgatory/Makefile | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
arch/x86/purgatory/Makefile +4 -1
@@ -15,7 +15,10 @@ $(obj)/sha256.o: $(srctree)/lib/sha256.c FORCE LDFLAGS_purgatory.ro := -e purgatory_start -r --no-undefined -nostdlib -z nodefaultlib targets += purgatory.ro +# Sanitizer, etc. runtimes are unavailable and cannot be linked here. +GCOV_PROFILE := n KASAN_SANITIZE := n +UBSAN_SANITIZE := n KCOV_INSTRUMENT := n # These are adjustments to the compiler flags used for objects that
@@ -23,7 +26,7 @@ KCOV_INSTRUMENT := n PURGATORY_CFLAGS_REMOVE := -mcmodel=kernel PURGATORY_CFLAGS := -mcmodel=large -ffreestanding -fno-zero-initialized-in-bss -PURGATORY_CFLAGS += $(DISABLE_STACKLEAK_PLUGIN) +PURGATORY_CFLAGS += $(DISABLE_STACKLEAK_PLUGIN) -DDISABLE_BRANCH_PROFILING # Default KBUILD_CFLAGS can have -pg option set when FTRACE is enabled. That # in turn leaves some undefined symbols like __fentry__ in purgatory and not
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 52/172 staging: greybus: fix a missing-check bug in gb_lights_light_config()
In reply to Sasha LevinFrom: Chen Zhou <[email protected]>
[ Upstream commit 9bb086e5ba9495ac150fbbcc5c8c2bccc06261dd ]
In gb_lights_light_config(), 'light->name' is allocated by kstrndup(). It returns NULL when fails, add check for it.
--- drivers/staging/greybus/light.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/staging/greybus/light.c +2 -1
@@ -1028,7 +1028,8 @@ static int gb_lights_light_config(struct gb_lights *glights, u8 id) light->channels_count = conf.channel_count; light->name =kstrndup (conf.name,NAMES_MAX ,GFP_KERNEL ); - +if (!light->name) +return -ENOMEM ; light->channels =kcalloc (light->channels_count,sizeof (struct gb_channel ),GFP_KERNEL );if (!light->channels)
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 53/172 staging: rtl8712: fix multiline derefernce warnings
In reply to Sasha LevinFrom: Aiman Najjar <[email protected]>
[ Upstream commit 269da10b1477c31c660288633c8d613e421b131f ]
This patch fixes remaining checkpatch warnings
in rtl871x_xmit.c:
WARNING: Avoid multiple line dereference - prefer 'psecuritypriv->PrivacyKeyIndex' 636: FILE: drivers/staging//rtl8712/rtl871x_xmit.c:636:
+ (u8)psecuritypriv->
+ PrivacyKeyIndex);
WARNING: Avoid multiple line dereference - prefer 'psecuritypriv->XGrpKeyid' 643: FILE: drivers/staging//rtl8712/rtl871x_xmit.c:643:
+ (u8)psecuritypriv->
+ XGrpKeyid);
WARNING: Avoid multiple line dereference - prefer 'psecuritypriv->XGrpKeyid' 652: FILE: drivers/staging//rtl8712/rtl871x_xmit.c:652:
+ (u8)psecuritypriv->
+ XGrpKeyid);
--- drivers/staging/rtl8712/rtl871x_xmit.c | 11 ++++------- 1 file changed, 4 insertions(+), 7 deletions(-)
drivers/staging/rtl8712/rtl871x_xmit.c +4 -7
@@ -601,7 +601,7 @@ sint r8712_xmitframe_coalesce(struct _adapter *padapter, _pkt *pkt,addr_t addr;u8 *pframe, *mem_start, *ptxdesc;struct sta_info *psta; -struct security_priv *psecuritypriv = &padapter->securitypriv; +struct security_priv *psecpriv = &padapter->securitypriv;struct mlme_priv *pmlmepriv = &padapter->mlmepriv;struct xmit_priv *pxmitpriv = &padapter->xmitpriv;struct pkt_attrib *pattrib = &pxmitframe->attrib;
@@ -644,15 +644,13 @@ sint r8712_xmitframe_coalesce(struct _adapter *padapter, _pkt *pkt,case _WEP40_:case _WEP104_:WEP_IV (pattrib->iv, psta->txpn, - (u8 )psecuritypriv-> - PrivacyKeyIndex); + (u8 )psecpriv->PrivacyKeyIndex);break ;case _TKIP_:if (bmcst)TKIP_IV (pattrib->iv, psta->txpn, - (u8 )psecuritypriv-> - XGrpKeyid); + (u8 )psecpriv->XGrpKeyid);else TKIP_IV (pattrib->iv, psta->txpn,0 );
@@ -660,8 +658,7 @@ sint r8712_xmitframe_coalesce(struct _adapter *padapter, _pkt *pkt,case _AES_:if (bmcst)AES_IV (pattrib->iv, psta->txpn, - (u8 )psecuritypriv-> - XGrpKeyid); + (u8 )psecpriv->XGrpKeyid);else AES_IV (pattrib->iv, psta->txpn,0 );
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 54/172 arm64: dts: mt8173: fix unit name warnings
In reply to Sasha LevinFrom: Hsin-Yi Wang <[email protected]>
[ Upstream commit 72b29215aced394d01ca25e432963b619daa0098 ]
Fixing several unit name warnings:
Warning (unit_address_vs_reg): /oscillator@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /oscillator@1: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /oscillator@2: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/trips/trip-point@0: node has a unit name, but no reg property Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/trips/trip-point@1: node has a unit name, but no reg property Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/trips/cpu_crit@0: node has a unit name, but no reg property Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/cooling-maps/map@0: node has a unit name, but no reg property Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/cooling-maps/map@1: node has a unit name, but no reg property Warning (unit_address_vs_reg): /reserved-memory/vpu_dma_mem_region: node has a reg or ranges property, but no unit name Warning (simple_bus_reg): /soc/pinctrl@10005000: simple-bus unit address format error, expected "1000b000" Warning (simple_bus_reg): /soc/interrupt-controller@10220000: simple-bus unit address format error, expected "10221000"
--- arch/arm64/boot/dts/mediatek/mt8173.dtsi | 22 +++++++++++----------- 1 file changed, 11 insertions(+), 11 deletions(-)
arch/arm64/boot/dts/mediatek/mt8173.dtsi +11 -11
@@ -223,21 +223,21 @@ psci { cpu_on = <0x84000003>; }; - clk26m: oscillator@0 { + clk26m: oscillator0 { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <26000000>; clock-output-names = "clk26m"; }; - clk32k: oscillator@1 { + clk32k: oscillator1 { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <32000>; clock-output-names = "clk32k"; }; - cpum_ck: oscillator@2 { + cpum_ck: oscillator2 { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <0>;
@@ -253,19 +253,19 @@ cpu_thermal: cpu_thermal { sustainable-power = <1500>; /* milliwatts */ trips { - threshold: trip-point@0 { + threshold: trip-point0 { temperature = <68000>; hysteresis = <2000>; type = "passive"; }; - target: trip-point@1 { + target: trip-point1 { temperature = <85000>; hysteresis = <2000>; type = "passive"; }; - cpu_crit: cpu_crit@0 { + cpu_crit: cpu_crit0 { temperature = <115000>; hysteresis = <2000>; type = "critical";
@@ -273,12 +273,12 @@ cpu_crit: cpu_crit@0 { }; cooling-maps { - map@0 { + map0 { trip = <&target>; cooling-device = <&cpu0 0 0>; contribution = <3072>; }; - map@1 { + map1 { trip = <&target>; cooling-device = <&cpu2 0 0>; contribution = <1024>;
@@ -291,7 +291,7 @@ reserved-memory { #address-cells = <2>; #size-cells = <2>; ranges; - vpu_dma_reserved: vpu_dma_mem_region { + vpu_dma_reserved: vpu_dma_mem_region@b7000000 { compatible = "shared-dma-pool"; reg = <0 0xb7000000 0 0x500000>; alignment = <0x1000>;
@@ -343,7 +343,7 @@ syscfg_pctl_a: syscfg_pctl_a@10005000 { reg = <0 0x10005000 0 0x1000>; }; - pio: pinctrl@10005000 { + pio: pinctrl@1000b000 { compatible = "mediatek,mt8173-pinctrl"; reg = <0 0x1000b000 0 0x1000>; mediatek,pctl-regmap = <&syscfg_pctl_a>;
@@ -541,7 +541,7 @@ mipi_tx1: mipi-dphy@10216000 { status = "disabled"; }; - gic: interrupt-controller@10220000 { + gic: interrupt-controller@10221000 { compatible = "arm,gic-400"; #interrupt-cells = <3>; interrupt-parent = <&gic>;
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Sasha Levin
maintainerPATCH 55/172 scsi: qedi: Do not flush offload work if ARP not resolved
In reply to Sasha LevinFrom: Nilesh Javali <[email protected]>
[ Upstream commit 927527aea0e2a9c1d336c7d33f77f1911481d008 ]
For an unreachable target, offload_work is not initialized and the endpoint state is set to OFLDCONN_NONE. This results in a WARN_ON due to the check of the work function field being set to zero.
------------[ cut here ]------------
WARNING: CPU: 24 PID: 18587 at ../kernel/workqueue.c:3037 __flush_work+0x1c1/0x1d0
:
Hardware name: HPE ProLiant DL380 Gen10/ProLiant DL380 Gen10, BIOS U30 02/01/2020
RIP: 0010:__flush_work+0x1c1/0x1d0
Code: ba 6d 00 03 80 c9 f0 eb b6 48 c7 c7 20 ee 6c a4 e8 52 d3 04 00 0f 0b 31 c0 e9 d1 fe ff
ff 48 c7 c7 20 ee 6c a4 e8 3d d3 04 00 <0f> 0b 31 c0 e9 bc fe ff ff e8 11 f3 f
00 31 f6
RSP: 0018:ffffac5a8cd47a80 EFLAGS: 00010282
RAX: 0000000000000024 RBX: ffff98d68c1fcaf0 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff98ce9fd99898 RDI: ffff98ce9fd99898
RBP: ffff98d68c1fcbc0 R08: 00000000000006fa R09: 0000000000000001
R10: ffffac5a8cd47b50 R11: 0000000000000001 R12: 0000000000000000
R13: 000000000000489b R14: ffff98d68c1fc800 R15: ffff98d692132c00
FS: 00007f65f7f62280(0000) GS:ffff98ce9fd80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffd2435e880 CR3: 0000000809334003 CR4: 00000000007606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
? class_create_release+0x40/0x40
? klist_put+0x2c/0x80
qedi_ep_disconnect+0xdd/0x400 [qedi]
iscsi_if_ep_disconnect.isra.20+0x59/0x70 [scsi_transport_iscsi]
iscsi_if_rx+0x129b/0x1670 [scsi_transport_iscsi]
? __netlink_lookup+0xe7/0x160
netlink_unicast+0x21d/0x300
netlink_sendmsg+0x30f/0x430
sock_sendmsg+0x5b/0x60
____sys_sendmsg+0x1e2/0x240
? copy_msghdr_from_user+0xd9/0x160
___sys_sendmsg+0x88/0xd0
? ___sys_recvmsg+0xa2/0xe0
? hrtimer_try_to_cancel+0x25/0x100
? do_nanosleep+0x9c/0x170
? __sys_sendmsg+0x5e/0xa0
__sys_sendmsg+0x5e/0xa0
do_syscall_64+0x60/0x1f0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7f65f6f16107
Code: 64 89 02 48 c7 c0 ff ff ff ff eb b9 0f 1f 80 00 00 00 00 8b 05 aa d2 2b 00 48 63 d2 48
63 ff 85 c0 75 18 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 59 f3 c3 0f 1f 8
0 00 00 00 00 53 48 89 f3 48
RSP: 002b:00007ffd24367ca8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 000055a7aeaaf110 RCX: 00007f65f6f16107
RDX: 0000000000000000 RSI: 00007ffd24367cc0 RDI: 0000000000000003
RBP: 0000000000000070 R08: 0000000000000000 R09: 0000000000000000
R10: 000000000000075c R11: 0000000000000246 R12: 00007ffd24367cc0
R13: 000055a7ae560008 R14: 00007ffd24367db0 R15: 0000000000000000
---[ end trace 54f499c05d41f8bb ]---Only flush if the connection endpoint state if different from OFLDCONN_NONE.
[mkp: clarified commit desc]
--- drivers/scsi/qedi/qedi_iscsi.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/scsi/qedi/qedi_iscsi.c +2 -1
@@ -1000,7 +1000,8 @@ static void qedi_ep_disconnect(struct iscsi_endpoint *ep)if (qedi_ep->state ==EP_STATE_OFLDCONN_START ) goto ep_exit_recover; -flush_work (&qedi_ep->offload_work); +if (qedi_ep->state !=EP_STATE_OFLDCONN_NONE ) +flush_work (&qedi_ep->offload_work);if (qedi_ep->conn) { qedi_conn = qedi_ep->conn;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 56/172 ARM: dts: sun8i-h2-plus-bananapi-m2-zero: Fix led polarity
In reply to Sasha LevinFrom: Vincent Stehlé <[email protected]>
[ Upstream commit 34b6826df7462c541752cf8b1de2691b26d78ae0 ]
The PWR-LED on the bananapi m2 zero board is on when gpio PL10 is low. This has been verified on a board and in the schematics [1].
[1]: http://wiki.banana-pi.org/Banana_Pi_BPI-M2_ZERO#Documents
--- arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts +1 -1
@@ -32,7 +32,7 @@ leds { pwr_led { label = "bananapi-m2-zero:red:pwr"; - gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ + gpios = <&r_pio 0 10 GPIO_ACTIVE_LOW>; /* PL10 */ default-state = "on"; }; };
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 57/172 gpio: dwapb: Append MODULE_ALIAS for platform driver
In reply to Sasha LevinFrom: Andy Shevchenko <[email protected]>
[ Upstream commit c58220cba2e03618659fa7d5dfae31f5ad4ae9d0 ]
The commit 3d2613c4289f
("GPIO: gpio-dwapb: Enable platform driver binding to MFD driver")
introduced a use of the platform driver but missed to add the following line to it:
MODULE_ALIAS("platform:gpio-dwapb");
Add this to get driver loaded automatically if platform device is registered.
--- drivers/gpio/gpio-dwapb.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-)
drivers/gpio/gpio-dwapb.c +6 -3
@@ -51,7 +51,9 @@#define GPIO_EXT_PORTC 0x58#define GPIO_EXT_PORTD 0x5c +#define DWAPB_DRIVER_NAME "gpio-dwapb"#define DWAPB_MAX_PORTS 4 +#define GPIO_EXT_PORT_STRIDE 0x04/* register stride 32 bits */ #define GPIO_SWPORT_DR_STRIDE 0x0c/* register stride 3*32 bits */ #define GPIO_SWPORT_DDR_STRIDE 0x0c/* register stride 3*32 bits */
@@ -400,7 +402,7 @@ static void dwapb_configure_irqs(struct dwapb_gpio *gpio,return ; err =irq_alloc_domain_generic_chips (gpio->domain, ngpio,2 , -"gpio-dwapb" , handle_level_irq, +DWAPB_DRIVER_NAME , handle_level_irq,IRQ_NOREQUEST ,0 ,IRQ_GC_INIT_NESTED_LOCK );if (err) {
@@ -457,7 +459,7 @@ static void dwapb_configure_irqs(struct dwapb_gpio *gpio,*/ err =devm_request_irq (gpio->dev, pp->irq[0 ], dwapb_irq_handler_mfd, -IRQF_SHARED ,"gpio-dwapb-mfd" , gpio); +IRQF_SHARED ,DWAPB_DRIVER_NAME , gpio);if (err) {dev_err (gpio->dev,"error requesting IRQ\n" );irq_domain_remove (gpio->domain);
@@ -849,7 +851,7 @@ static SIMPLE_DEV_PM_OPS(dwapb_gpio_pm_ops, dwapb_gpio_suspend,static struct platform_driver dwapb_gpio_driver = { .driver = { - .name ="gpio-dwapb" , + .name =DWAPB_DRIVER_NAME , .pm = &dwapb_gpio_pm_ops, .of_match_table =of_match_ptr (dwapb_of_match), .acpi_match_table =ACPI_PTR (dwapb_acpi_match),
@@ -863,3 +865,4 @@ module_platform_driver(dwapb_gpio_driver);MODULE_LICENSE ("GPL" );MODULE_AUTHOR ("Jamie Iles" );MODULE_DESCRIPTION ("Synopsys DesignWare APB GPIO driver" ); +MODULE_ALIAS ("platform:" DWAPB_DRIVER_NAME );
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 58/172 scsi: qedf: Fix crash when MFW calls for protocol stats while function is still probing
In reply to Sasha LevinFrom: Chad Dupuis <[email protected]>
[ Upstream commit ad40f5256095c68dc17c991eb976261d5ea2daaa ]
The MFW may make a call to qed and then to qedf for protocol statistics while the function is still probing. If this happens it's possible that some members of the struct qedf_ctx may not be fully initialized which can result in a NULL pointer dereference or general protection fault.
To prevent this, add a new flag call QEDF_PROBING and set it when the __qedf_probe() function is active. Then in the qedf_get_protocol_tlv_data() function we can check if the function is still probing and return immediantely before any uninitialized structures can be touched.
--- drivers/scsi/qedf/qedf.h | 1 + drivers/scsi/qedf/qedf_main.c | 35 +++++++++++++++++++++++++++++++---- 2 files changed, 32 insertions(+), 4 deletions(-)
drivers/scsi/qedf/qedf.h +1 -0
@@ -335,6 +335,7 @@ struct qedf_ctx {#define QEDF_GRCDUMP_CAPTURE 4#define QEDF_IN_RECOVERY 5#define QEDF_DBG_STOP_IO 6 +#define QEDF_PROBING 8unsigned long flags;/* Miscellaneous state flags */ int fipvlan_retries;u8 num_queues;
drivers/scsi/qedf/qedf_main.c +31 -4
@@ -2961,7 +2961,7 @@ static int __qedf_probe(struct pci_dev *pdev, int mode) {int rc = -EINVAL ;struct fc_lport *lport; -struct qedf_ctx *qedf; +struct qedf_ctx *qedf =NULL ;struct Scsi_Host *host;bool is_vf = false;struct qed_ll2_params params;
@@ -2989,6 +2989,7 @@ static int __qedf_probe(struct pci_dev *pdev, int mode)/* Initialize qedf_ctx */ qedf =lport_priv (lport); +set_bit (QEDF_PROBING , &qedf->flags); qedf->lport = lport; qedf->ctlr.lp = lport; qedf->pdev = pdev;
@@ -3011,9 +3012,12 @@ static int __qedf_probe(struct pci_dev *pdev, int mode) }else {/* Init pointers during recovery */ qedf =pci_get_drvdata (pdev); +set_bit (QEDF_PROBING , &qedf->flags); lport = qedf->lport; } +QEDF_INFO (&qedf->dbg_ctx,QEDF_LOG_DISC ,"Probe started.\n" ); + host = lport->host;/* Allocate mempool for qedf_io_work structs */
@@ -3312,6 +3316,10 @@ static int __qedf_probe(struct pci_dev *pdev, int mode)else fc_fabric_login (lport); +QEDF_INFO (&qedf->dbg_ctx,QEDF_LOG_DISC ,"Probe done.\n" ); + +clear_bit (QEDF_PROBING , &qedf->flags); +/* All good */ return 0 ;
@@ -3337,6 +3345,11 @@ static int __qedf_probe(struct pci_dev *pdev, int mode) err1:scsi_host_put (lport->host); err0: +if (qedf) { +QEDF_INFO (&qedf->dbg_ctx,QEDF_LOG_DISC ,"Probe done.\n" ); + +clear_bit (QEDF_PROBING , &qedf->flags); + }return rc; }
@@ -3484,11 +3497,25 @@ void qedf_get_protocol_tlv_data(void *dev, void *data) {struct qedf_ctx *qedf = dev;struct qed_mfw_tlv_fcoe *fcoe = data; -struct fc_lport *lport = qedf->lport; -struct Scsi_Host *host = lport->host; -struct fc_host_attrs *fc_host =shost_to_fc_host (host); +struct fc_lport *lport; +struct Scsi_Host *host; +struct fc_host_attrs *fc_host;struct fc_host_statistics *hst; +if (!qedf) { +QEDF_ERR (NULL ,"qedf is null.\n" ); +return ; + } + +if (test_bit (QEDF_PROBING , &qedf->flags)) { +QEDF_ERR (&qedf->dbg_ctx,"Function is still probing.\n" ); +return ; + } + + lport = qedf->lport; + host = lport->host; + fc_host =shost_to_fc_host (host); +/* Force a refresh of the fc_host stats including offload stats */ hst =qedf_fc_get_host_stats (host);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 59/172 iio: buffer: Don't allow buffers without any channels enabled to be activated
In reply to Sasha LevinFrom: Lars-Peter Clausen <[email protected]>
[ Upstream commit b7329249ea5b08b2a1c2c3f24a2f4c495c4f14b8 ]
Before activating a buffer make sure that at least one channel is enabled. Activating a buffer with 0 channels enabled doesn't make too much sense and disallowing this case makes sure that individual driver don't have to add special case code to handle it.
Currently, without this patch enabling a buffer is possible and no error is produced. With this patch -EINVAL is returned.
An example of execution with this patch and some instrumented print-code:
root@analog:~# cd /sys/bus/iio/devices/iio\:device3/buffer root@analog:/sys/bus/iio/devices/iio:device3/buffer# echo 1 > enable 0: iio_verify_update 748 indio_dev->masklength 2 *insert_buffer->scan_mask 00000000 1: iio_verify_update 753 2:__iio_update_buffers 1115 ret -22 3: iio_buffer_store_enable 1241 ret -22 -bash: echo: write error: Invalid argument 1, 2 & 3 are exit-error paths. 0 the first print in iio_verify_update() rergardless of error path.
Without this patch (and same instrumented print-code):
root@analog:~# cd /sys/bus/iio/devices/iio\:device3/buffer root@analog:/sys/bus/iio/devices/iio:device3/buffer# echo 1 > enable 0: iio_verify_update 748 indio_dev->masklength 2 *insert_buffer->scan_mask 00000000 root@analog:/sys/bus/iio/devices/iio:device3/buffer# Buffer is enabled with no error.
Note from Jonathan: Probably not suitable for automatic application to stable. This has been there from the very start. It tidies up an odd corner case but won't effect any 'real' users.
--- drivers/iio/industrialio-buffer.c | 7 +++++++ 1 file changed, 7 insertions(+)
drivers/iio/industrialio-buffer.c +7 -0
@@ -691,6 +691,13 @@ static int iio_verify_update(struct iio_dev *indio_dev,bool scan_timestamp;unsigned int modes; +if (insert_buffer && +bitmap_empty (insert_buffer->scan_mask, indio_dev->masklength)) { +dev_dbg (&indio_dev->dev, +"At least one scan element must be enabled first\n" ); +return -EINVAL ; + } +memset (config,0 ,sizeof (*config)); config->watermark = ~0 ;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 60/172 pinctrl: rza1: Fix wrong array assignment of rza1l_swio_entries
In reply to Sasha LevinFrom: Jason Yan <[email protected]>
[ Upstream commit 4b4e8e93eccc2abc4209fe226ec89e7fbe9f3c61 ]
The rza1l_swio_entries referred to the wrong array rza1h_swio_pins, which was intended to be rza1l_swio_pins. So let's fix it.
This is detected by the following gcc warning:
drivers/pinctrl/pinctrl-rza1.c:401:35: warning: ‘rza1l_swio_pins’ defined but not used [-Wunused-const-variable=]
static const struct rza1_swio_pin rza1l_swio_pins[] = {
^~~~~~~~~~~~~~~--- drivers/pinctrl/pinctrl-rza1.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/pinctrl/pinctrl-rza1.c +1 -1
@@ -421,7 +421,7 @@ static const struct rza1_bidir_entry rza1l_bidir_entries[RZA1_NPORTS] = { };static const struct rza1_swio_entry rza1l_swio_entries[] = { - [0 ] = {ARRAY_SIZE (rza1h_swio_pins), rza1h_swio_pins }, + [0 ] = {ARRAY_SIZE (rza1l_swio_pins), rza1l_swio_pins }, };/* RZ/A1L (r7s72102x) pinmux flags table */
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 61/172 firmware: qcom_scm: fix bogous abuse of dma-direct internals
In reply to Sasha LevinFrom: Christoph Hellwig <[email protected]>
[ Upstream commit 459b1f86f1cba7de813fbc335df476c111feec22 ]
As far as the device is concerned the dma address is the physical address. There is no need to convert it to a physical address, especially not using dma-direct internals that are not available to drivers and which will interact badly with IOMMUs. Last but not least the commit introducing it claimed to just fix a type issue, but actually changed behavior.
--- drivers/firmware/qcom_scm.c | 9 +++------ 1 file changed, 3 insertions(+), 6 deletions(-)
drivers/firmware/qcom_scm.c +3 -6
@@ -18,7 +18,6 @@#include <linux/init.h> #include <linux/cpumask.h> #include <linux/export.h> -#include <linux/dma-direct.h> #include <linux/dma-mapping.h> #include <linux/module.h> #include <linux/types.h>
@@ -449,8 +448,7 @@ int qcom_scm_assign_mem(phys_addr_t mem_addr, size_t mem_sz,struct qcom_scm_mem_map_info *mem_to_map;phys_addr_t mem_to_map_phys;phys_addr_t dest_phys; -phys_addr_t ptr_phys; -dma_addr_t ptr_dma; +dma_addr_t ptr_phys;size_t mem_to_map_sz;size_t dest_sz;size_t src_sz;
@@ -468,10 +466,9 @@ int qcom_scm_assign_mem(phys_addr_t mem_addr, size_t mem_sz, ptr_sz =ALIGN (src_sz,SZ_64 ) +ALIGN (mem_to_map_sz,SZ_64 ) +ALIGN (dest_sz,SZ_64 ); - ptr =dma_alloc_coherent (__scm->dev, ptr_sz, &ptr_dma,GFP_KERNEL ); + ptr =dma_alloc_coherent (__scm->dev, ptr_sz, &ptr_phys,GFP_KERNEL );if (!ptr)return -ENOMEM ; - ptr_phys =dma_to_phys (__scm->dev, ptr_dma);/* Fill source vmid detail */ src = ptr;
@@ -501,7 +498,7 @@ int qcom_scm_assign_mem(phys_addr_t mem_addr, size_t mem_sz, ret =__qcom_scm_assign_mem (__scm->dev, mem_to_map_phys, mem_to_map_sz, ptr_phys, src_sz, dest_phys, dest_sz); -dma_free_coherent (__scm->dev, ptr_sz, ptr, ptr_dma); +dma_free_coherent (__scm->dev, ptr_sz, ptr, ptr_phys);if (ret) {dev_err (__scm->dev,"Assign memory protection call failed %d.\n" , ret);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 62/172 staging: gasket: Fix mapping refcnt leak when put attribute fails
In reply to Sasha LevinFrom: Xiyu Yang <[email protected]>
[ Upstream commit 57a66838e1494cd881b7f4e110ec685736e8e3ca ]
gasket_sysfs_put_attr() invokes get_mapping(), which returns a reference of the specified gasket_sysfs_mapping object to "mapping" with increased refcnt.
When gasket_sysfs_put_attr() returns, local variable "mapping" becomes invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one path of gasket_sysfs_put_attr(). When mapping attribute is unknown, the function forgets to decrease the refcnt increased by get_mapping(), causing a refcnt leak.
Fix this issue by calling put_mapping() when put attribute fails due to unknown attribute.
--- drivers/staging/gasket/gasket_sysfs.c | 1 + 1 file changed, 1 insertion(+)
drivers/staging/gasket/gasket_sysfs.c +1 -0
@@ -343,6 +343,7 @@ void gasket_sysfs_put_attr(struct device *device,dev_err (device,"Unable to put unknown attribute: %s\n" , attr->attr.attr.name); +put_mapping (mapping); }EXPORT_SYMBOL (gasket_sysfs_put_attr);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 63/172 staging: gasket: Fix mapping refcnt leak when register/store fails
In reply to Sasha LevinFrom: Xiyu Yang <[email protected]>
[ Upstream commit e3436ce60cf5f5eaedda2b8c622f69feb97595e2 ]
gasket_sysfs_register_store() invokes get_mapping(), which returns a reference of the specified gasket_sysfs_mapping object to "mapping" with increased refcnt.
When gasket_sysfs_register_store() returns, local variable "mapping" becomes invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of gasket_sysfs_register_store(). When gasket_dev is NULL, the function forgets to decrease the refcnt increased by get_mapping(), causing a refcnt leak.
Fix this issue by calling put_mapping() when gasket_dev is NULL.
--- drivers/staging/gasket/gasket_sysfs.c | 1 + 1 file changed, 1 insertion(+)
drivers/staging/gasket/gasket_sysfs.c +1 -0
@@ -377,6 +377,7 @@ ssize_t gasket_sysfs_register_store(struct device *device, gasket_dev = mapping->gasket_dev;if (!gasket_dev) {dev_err (device,"Device driver may have been removed\n" ); +put_mapping (mapping);return 0 ; }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 64/172 ALSA: usb-audio: Improve frames size computation
In reply to Sasha LevinFrom: Alexander Tsoy <[email protected]>
[ Upstream commit f0bd62b64016508938df9babe47f65c2c727d25c ]
For computation of the the next frame size current value of fs/fps and accumulated fractional parts of fs/fps are used, where values are stored in Q16.16 format. This is quite natural for computing frame size for asynchronous endpoints driven by explicit feedback, since in this case fs/fps is a value provided by the feedback endpoint and it's already in the Q format. If an error is accumulated over time, the device can adjust fs/fps value to prevent buffer overruns/underruns.
But for synchronous endpoints the accuracy provided by these computations is not enough. Due to accumulated error the driver periodically produces frames with incorrect size (+/- 1 audio sample).
This patch fixes this issue by implementing a different algorithm for frame size computation. It is based on accumulating of the remainders from division fs/fps and it doesn't accumulate errors over time. This new method is enabled for synchronous and adaptive playback endpoints.
--- sound/usb/card.h | 4 ++++ sound/usb/endpoint.c | 43 ++++++++++++++++++++++++++++++++++++++----- sound/usb/endpoint.h | 1 + sound/usb/pcm.c | 2 ++ 4 files changed, 45 insertions(+), 5 deletions(-)
sound/usb/card.h +4 -0
@@ -83,6 +83,10 @@ struct snd_usb_endpoint {dma_addr_t sync_dma;/* DMA address of syncbuf */ unsigned int pipe;/* the data i/o pipe */ +unsigned int framesize[2 ];/* small/large frame sizes in samples */ +unsigned int sample_rem;/* remainder from division fs/fps */ +unsigned int sample_accum;/* sample accumulator */ +unsigned int fps;/* frames per second */ unsigned int freqn;/* nominal sampling rate in fs/fps in Q16.16 format */ unsigned int freqm;/* momentary sampling rate in fs/fps in Q16.16 format */ int freqshift;/* how much to shift the feedback value to get Q16.16 */
sound/usb/endpoint.c +38 -5
78 lines not on this page · raw message
sound/usb/endpoint.h +1 -0
@@ -28,6 +28,7 @@ void snd_usb_endpoint_release(struct snd_usb_endpoint *ep);void snd_usb_endpoint_free (struct snd_usb_endpoint *ep);int snd_usb_endpoint_implicit_feedback_sink (struct snd_usb_endpoint *ep); +int snd_usb_endpoint_slave_next_packet_size (struct snd_usb_endpoint *ep);int snd_usb_endpoint_next_packet_size (struct snd_usb_endpoint *ep); void snd_usb_handle_sync_urb(struct snd_usb_endpoint *ep,
sound/usb/pcm.c +2 -0
@@ -1558,6 +1558,8 @@ static void prepare_playback_urb(struct snd_usb_substream *subs,for (i =0 ; i < ctx->packets; i++) {if (ctx->packet_size[i]) counts = ctx->packet_size[i]; +else if (ep->sync_master) + counts =snd_usb_endpoint_slave_next_packet_size (ep);else counts =snd_usb_endpoint_next_packet_size (ep);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 65/172 ALSA: usb-audio: Fix racy list management in output queue
In reply to Sasha LevinFrom: Takashi Iwai <[email protected]>
[ Upstream commit 5b6cc38f3f3f37109ce72b60bda215a5f6892c0b ]
The linked list entry from FIFO is peeked at queue_pending_output_urbs() but the actual element pop-out is performed outside the spinlock, and it's potentially racy.
Do delete the link at the right place inside the spinlock.
--- sound/usb/endpoint.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
sound/usb/endpoint.c +3 -3
@@ -359,17 +359,17 @@ static void queue_pending_output_urbs(struct snd_usb_endpoint *ep) ep->next_packet_read_pos %=MAX_URBS ;/* take URB out of FIFO */ -if (!list_empty (&ep->ready_playback_urbs)) +if (!list_empty (&ep->ready_playback_urbs)) { ctx =list_first_entry (&ep->ready_playback_urbs, struct snd_urb_ctx, ready_list); +list_del_init (&ctx->ready_list); + } }spin_unlock_irqrestore (&ep->lock, flags);if (ctx ==NULL )return ; -list_del_init (&ctx->ready_list); -/* copy over the length information */ for (i =0 ; i < packet->packets; i++) ctx->packet_size[i] = packet->packet_size[i];
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 66/172 Input: mms114 - add extra compatible for mms345l
In reply to Sasha LevinFrom: Stephan Gerhold <[email protected]>
[ Upstream commit 7842087b0196d674ed877d768de8f2a34d7fdc53 ]
MMS345L is another first generation touch screen from Melfas, which uses mostly the same registers as MMS152.
However, there is some garbage printed during initialization. Apparently MMS345L does not have the MMS152_COMPAT_GROUP register that is read+printed during initialization.
TSP FW Rev: bootloader 0x6 / core 0x26 / config 0x26, Compat group: \x06
On earlier kernel versions the compat group was actually printed as an ASCII control character, seems like it gets escaped now.
But we probably shouldn't print something from a random register.
Add a separate "melfas,mms345l" compatible that avoids reading from the MMS152_COMPAT_GROUP register. This might also help in case there is some other device-specific quirk in the future.
--- drivers/input/touchscreen/mms114.c | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-)
drivers/input/touchscreen/mms114.c +15 -2
@@ -54,6 +54,7 @@enum mms_type {TYPE_MMS114 =114 ,TYPE_MMS152 =152 , +TYPE_MMS345L =345 , };struct mms114_data {
@@ -250,6 +251,15 @@ static int mms114_get_version(struct mms114_data *data)int error;switch (data->type) { +case TYPE_MMS345L : + error =__mms114_read_reg (data,MMS152_FW_REV ,3 , buf); +if (error) +return error; + +dev_info (dev,"TSP FW Rev: bootloader 0x%x / core 0x%x / config 0x%x\n" , + buf[0 ], buf[1 ], buf[2 ]); +break ; +case TYPE_MMS152 : error =__mms114_read_reg (data,MMS152_FW_REV ,3 , buf);if (error)
@@ -287,8 +297,8 @@ static int mms114_setup_regs(struct mms114_data *data)if (error <0 )return error; -/* MMS152 has no configuration or power on registers */ -if (data->type ==TYPE_MMS152 ) +/* Only MMS114 has configuration and power on registers */ +if (data->type !=TYPE_MMS114 )return 0 ; error =mms114_set_active (data, true);
@@ -600,6 +610,9 @@ static const struct of_device_id mms114_dt_match[] = { }, { .compatible = "melfas,mms152", .data = (void *)TYPE_MMS152, + }, { + .compatible = "melfas,mms345l", + .data = (void *)TYPE_MMS345L, }, { } };
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 67/172 s390/qdio: put thinint indicator after early error
In reply to Sasha LevinFrom: Julian Wiedmann <[email protected]>
[ Upstream commit 75e82bec6b2622c6f455b7a543fb5476a5d0eed7 ]
qdio_establish() calls qdio_setup_thinint() via qdio_setup_irq(). If the subsequent qdio_establish_thinint() fails, we miss to put the DSCI again. Thus the DSCI isn't available for re-use. Given enough of such errors, we could end up with having only the shared DSCI available.
Merge qdio_setup_thinint() into qdio_establish_thinint(), and deal with such an error internally.
--- drivers/s390/cio/qdio.h | 1 - drivers/s390/cio/qdio_setup.c | 1 - drivers/s390/cio/qdio_thinint.c | 14 ++++++++------ 3 files changed, 8 insertions(+), 8 deletions(-)
drivers/s390/cio/qdio.h +0 -1
@@ -377,7 +377,6 @@ static inline int multicast_outbound(struct qdio_q *q)extern u64 last_ai_time;/* prototypes for thin interrupt */ -void qdio_setup_thinint (struct qdio_irq *irq_ptr);int qdio_establish_thinint (struct qdio_irq *irq_ptr);void qdio_shutdown_thinint (struct qdio_irq *irq_ptr);void tiqdio_add_input_queues (struct qdio_irq *irq_ptr);
drivers/s390/cio/qdio_setup.c +0 -1
@@ -480,7 +480,6 @@ int qdio_setup_irq(struct qdio_initialize *init_data)setup_queues (irq_ptr, init_data);setup_qib (irq_ptr, init_data); -qdio_setup_thinint (irq_ptr); set_impl_params(irq_ptr, init_data->qib_param_field_format, init_data->qib_param_field, init_data->input_slib_elements,
drivers/s390/cio/qdio_thinint.c +8 -6
@@ -267,17 +267,19 @@ int __init tiqdio_register_thinints(void)int qdio_establish_thinint (struct qdio_irq *irq_ptr) { +int rc; +if (!is_thinint_irq (irq_ptr))return 0 ; -return set_subchannel_ind (irq_ptr,0 ); -} -void qdio_setup_thinint (struct qdio_irq *irq_ptr) -{ -if (!is_thinint_irq (irq_ptr)) -return ; irq_ptr->dsci =get_indicator ();DBF_HEX (&irq_ptr->dsci,sizeof (void *)); + + rc =set_subchannel_ind (irq_ptr,0 ); +if (rc) +put_indicator (irq_ptr->dsci); + +return rc; }void qdio_shutdown_thinint (struct qdio_irq *irq_ptr)
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 68/172 tty: hvc: Fix data abort due to race in hvc_open
In reply to Sasha LevinFrom: Raghavendra Rao Ananta <[email protected]>
[ Upstream commit e2bd1dcbe1aa34ff5570b3427c530e4332ecf0fe ]
Potentially, hvc_open() can be called in parallel when two tasks calls open() on /dev/hvcX. In such a scenario, if the hp->ops->notifier_add() callback in the function fails, where it sets the tty->driver_data to NULL, the parallel hvc_open() can see this NULL and cause a memory abort. Hence, serialize hvc_open and check if tty->private_data is NULL before proceeding ahead.
The issue can be easily reproduced by launching two tasks simultaneously that does nothing but open() and close() on /dev/hvcX.
For example:
$ ./simple_open_close /dev/hvc0 & ./simple_open_close /dev/hvc0 &
--- drivers/tty/hvc/hvc_console.c | 16 ++++++++++++++-- 1 file changed, 14 insertions(+), 2 deletions(-)
drivers/tty/hvc/hvc_console.c +14 -2
@@ -75,6 +75,8 @@ static LIST_HEAD(hvc_structs);*/ static DEFINE_MUTEX (hvc_structs_mutex); +/* Mutex to serialize hvc_open */ +static DEFINE_MUTEX (hvc_open_mutex);/* * This value is used to assign a tty->index value to a hvc_struct based * upon order of exposure via hvc_probe(), when we can not match it to
@@ -346,16 +348,24 @@ static int hvc_install(struct tty_driver *driver, struct tty_struct *tty)*/ static int hvc_open (struct tty_struct *tty,struct file * filp) { -struct hvc_struct *hp = tty->driver_data; +struct hvc_struct *hp;unsigned long flags;int rc =0 ; +mutex_lock (&hvc_open_mutex); + + hp = tty->driver_data; +if (!hp) { + rc = -EIO ; + goto out; + } +spin_lock_irqsave (&hp->port.lock, flags);/* Check and then increment for fast path open. */ if (hp->port.count++ >0 ) {spin_unlock_irqrestore (&hp->port.lock, flags);hvc_kick (); -return 0 ; + goto out; }/* else count == 0 */ spin_unlock_irqrestore (&hp->port.lock, flags);
@@ -383,6 +393,8 @@ static int hvc_open(struct tty_struct *tty, struct file * filp)/* Force wakeup of the polling thread */ hvc_kick (); +out: +mutex_unlock (&hvc_open_mutex);return rc; }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 69/172 slimbus: ngd: get drvdata from correct device
In reply to Sasha LevinFrom: Srinivas Kandagatla <[email protected]>
[ Upstream commit b58c663059b484f7ff547d076a34cf6d7a302e56 ]
Get drvdata directly from parent instead of ngd dev, as ngd dev can probe defer and previously set drvdata will become null.
--- drivers/slimbus/qcom-ngd-ctrl.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/slimbus/qcom-ngd-ctrl.c +2 -2
@@ -1350,7 +1350,6 @@ static int of_qcom_slim_ngd_register(struct device *parent, ngd->pdev->driver_override =QCOM_SLIM_NGD_DRV_NAME ; ngd->pdev->dev.of_node = node; ctrl->ngd = ngd; -platform_set_drvdata (ngd->pdev, ctrl);platform_device_add (ngd->pdev); ngd->base = ctrl->base + ngd->id * data->offset +
@@ -1365,12 +1364,13 @@ static int of_qcom_slim_ngd_register(struct device *parent,static int qcom_slim_ngd_probe (struct platform_device *pdev) { -struct qcom_slim_ngd_ctrl *ctrl =platform_get_drvdata (pdev);struct device *dev = &pdev->dev; +struct qcom_slim_ngd_ctrl *ctrl =dev_get_drvdata (dev->parent);int ret; ctrl->ctrl.dev = dev; +platform_set_drvdata (pdev, ctrl);pm_runtime_use_autosuspend (dev);pm_runtime_set_autosuspend_delay (dev,QCOM_SLIM_NGD_AUTOSUSPEND );pm_runtime_set_suspended (dev);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 70/172 thermal/drivers/ti-soc-thermal: Avoid dereferencing ERR_PTR
In reply to Sasha LevinFrom: Sudip Mukherjee <[email protected]>
[ Upstream commit 7440f518dad9d861d76c64956641eeddd3586f75 ]
On error the function ti_bandgap_get_sensor_data() returns the error code in ERR_PTR() but we only checked if the return value is NULL or not. And, so we can dereference an error code inside ERR_PTR. While at it, convert a check to IS_ERR_OR_NULL.
--- drivers/thermal/ti-soc-thermal/ti-thermal-common.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/thermal/ti-soc-thermal/ti-thermal-common.c +3 -3
@@ -183,7 +183,7 @@ int ti_thermal_expose_sensor(struct ti_bandgap *bgp, int id, data =ti_bandgap_get_sensor_data (bgp, id); -if (!data ||IS_ERR (data)) +if (!IS_ERR_OR_NULL (data)) data =ti_thermal_build_data (bgp, id);if (!data)
@@ -210,7 +210,7 @@ int ti_thermal_remove_sensor(struct ti_bandgap *bgp, int id) data =ti_bandgap_get_sensor_data (bgp, id); -if (data && data->ti_thermal) { +if (!IS_ERR_OR_NULL (data) && data->ti_thermal) {if (data->our_zone)thermal_zone_device_unregister (data->ti_thermal); }
@@ -276,7 +276,7 @@ int ti_thermal_unregister_cpu_cooling(struct ti_bandgap *bgp, int id) data =ti_bandgap_get_sensor_data (bgp, id); -if (data) { +if (!IS_ERR_OR_NULL (data)) {cpufreq_cooling_unregister (data->cool_dev);if (data->policy)cpufreq_cpu_put (data->policy);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 71/172 soundwire: slave: don't init debugfs on device registration error
In reply to Sasha LevinFrom: Pierre-Louis Bossart <[email protected]>
[ Upstream commit 8893ab5e8ee5d7c12e0fc1dca4a309475064473d ]
The error handling flow seems incorrect, there is no reason to try and add debugfs support if the device registration did not succeed. Return on error.
--- drivers/soundwire/slave.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/soundwire/slave.c +2 -0
@@ -55,6 +55,8 @@ static int sdw_slave_add(struct sdw_bus *bus,list_del (&slave->node);mutex_unlock (&bus->bus_lock);put_device (&slave->dev); + +return ret; }return ret;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 72/172 usb: dwc3: gadget: Properly handle failed kick_transfer
In reply to Sasha LevinFrom: Thinh Nguyen <[email protected]>
[ Upstream commit 8d99087c2db863c5fa3a4a1f3cb82b3a493705ca ]
If dwc3 fails to issue START_TRANSFER/UPDATE_TRANSFER command, then we should properly end an active transfer and give back all the started requests. However if it's for an isoc endpoint, the failure maybe due to bus-expiry status. In this case, don't give back the requests and wait for the next retry.
--- drivers/usb/dwc3/gadget.c | 24 ++++++++++++++++-------- 1 file changed, 16 insertions(+), 8 deletions(-)
drivers/usb/dwc3/gadget.c +16 -8
@@ -1217,6 +1217,8 @@ static void dwc3_prepare_trbs(struct dwc3_ep *dep) } } +static void dwc3_gadget_ep_cleanup_cancelled_requests (struct dwc3_ep *dep); +static int __dwc3_gadget_kick_transfer (struct dwc3_ep *dep) {struct dwc3_gadget_ep_cmd_params params;
@@ -1253,14 +1255,20 @@ static int __dwc3_gadget_kick_transfer(struct dwc3_ep *dep) ret =dwc3_send_gadget_ep_cmd (dep, cmd, ¶ms);if (ret <0 ) { -/* -* FIXME we need to iterate over the list of requests -* here and stop, unmap, free and del each of the linked -* requests instead of what we do now. -*/ -if (req->trb) -memset (req->trb,0 ,sizeof (struct dwc3_trb )); -dwc3_gadget_del_and_unmap_request (dep, req, ret); +struct dwc3_request *tmp; + +if (ret == -EAGAIN ) +return ret; + +dwc3_stop_active_transfer (dep, true, true); + +list_for_each_entry_safe (req, tmp, &dep->started_list, list) +dwc3_gadget_move_cancelled_request (req); + +/* If ep isn't started, then there's no end transfer pending */ +if (!(dep->flags &DWC3_EP_END_TRANSFER_PENDING )) +dwc3_gadget_ep_cleanup_cancelled_requests (dep); +return ret; }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 73/172 staging: sm750fb: add missing case while setting FB_VISUAL
In reply to Sasha LevinFrom: Matej Dujava <[email protected]>
[ Upstream commit fa90133377f4a7f15a937df6ad55133bb57c5665 ]
Switch statement does not contain all cases: 8, 16, 24, 32. This patch will add missing one (24)
--- drivers/staging/sm750fb/sm750.c | 1 + 1 file changed, 1 insertion(+)
drivers/staging/sm750fb/sm750.c +1 -0
@@ -897,6 +897,7 @@ static int lynxfb_set_fbinfo(struct fb_info *info, int index) fix->visual =FB_VISUAL_PSEUDOCOLOR ;break ;case 16 : +case 24 :case 32 : fix->visual =FB_VISUAL_TRUECOLOR ;break ;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 74/172 PCI: v3-semi: Fix a memory leak in v3_pci_probe() error handling paths
In reply to Sasha LevinFrom: Christophe JAILLET <[email protected]>
[ Upstream commit bca718988b9008d0d5f504e2d318178fc84958c1 ]
If we fails somewhere in 'v3_pci_probe()', we need to free 'host'.
Use the managed version of 'pci_alloc_host_bridge()' to do that easily. The use of managed resources is already widely used in this driver.
--- drivers/pci/controller/pci-v3-semi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/pci/controller/pci-v3-semi.c +1 -1
@@ -743,7 +743,7 @@ static int v3_pci_probe(struct platform_device *pdev)int ret;LIST_HEAD (res); - host =pci_alloc_host_bridge (sizeof (*v3)); + host =devm_pci_alloc_host_bridge (dev,sizeof (*v3));if (!host)return -ENOMEM ;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 75/172 i2c: pxa: fix i2c_pxa_scream_blue_murder() debug output
In reply to Sasha LevinFrom: Russell King <[email protected]>
[ Upstream commit 88b73ee7ca4c90baf136ed5a8377fc5a9b73ac08 ]
The IRQ log output is supposed to appear on a single line. However, commit 3a2dc1677b60 ("i2c: pxa: Update debug function to dump more info on error") resulted in it being printed one-entry-per-line, which is excessively long.
Fixing this is not a trivial matter; using pr_cont() doesn't work as the previous dev_dbg() may not have been compiled in, or may be dynamic.
Since the rest of this function output is at error level, and is also debug output, promote this to error level as well to avoid this problem.
Reduce the number of always zero prefix digits to save screen real- estate.
--- drivers/i2c/busses/i2c-pxa.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-)
drivers/i2c/busses/i2c-pxa.c +3 -4
@@ -315,11 +315,10 @@ static void i2c_pxa_scream_blue_murder(struct pxa_i2c *i2c, const char *why)dev_err (dev,"IBMR: %08x IDBR: %08x ICR: %08x ISR: %08x\n" ,readl (_IBMR (i2c)),readl (_IDBR (i2c)),readl (_ICR (i2c)),readl (_ISR (i2c))); -dev_dbg (dev,"log: " ); +dev_err (dev,"log:" );for (i =0 ; i < i2c->irqlogidx; i++) -pr_debug ("[%08x:%08x] " , i2c->isrlog[i], i2c->icrlog[i]); - - pr_debug("\n"); +pr_cont (" [%03x:%05x]" , i2c->isrlog[i], i2c->icrlog[i]); + pr_cont("\n"); }#else /* ifdef DEBUG */
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 76/172 serial: amba-pl011: Make sure we initialize the port.lock spinlock
In reply to Sasha LevinFrom: John Stultz <[email protected]>
[ Upstream commit 8508f4cba308f785b2fd4b8c38849c117b407297 ]
Valentine reported seeing:
[ 3.626638] INFO: trying to register non-static key. [ 3.626639] the code is fine but needs lockdep annotation. [ 3.626640] turning off the locking correctness validator. [ 3.626644] CPU: 7 PID: 51 Comm: kworker/7:1 Not tainted 5.7.0-rc2-00115-g8c2e9790f196 #116 [ 3.626646] Hardware name: HiKey960 (DT) [ 3.626656] Workqueue: events deferred_probe_work_func [ 3.632476] sd 0:0:0:0: [sda] Optimal transfer size 8192 bytes not a multiple of physical block size (16384 bytes) [ 3.640220] Call trace: [ 3.640225] dump_backtrace+0x0/0x1b8 [ 3.640227] show_stack+0x20/0x30 [ 3.640230] dump_stack+0xec/0x158 [ 3.640234] register_lock_class+0x598/0x5c0 [ 3.640235] __lock_acquire+0x80/0x16c0 [ 3.640236] lock_acquire+0xf4/0x4a0 [ 3.640241] _raw_spin_lock_irqsave+0x70/0xa8 [ 3.640245] uart_add_one_port+0x388/0x4b8 [ 3.640248] pl011_register_port+0x70/0xf0 [ 3.640250] pl011_probe+0x184/0x1b8 [ 3.640254] amba_probe+0xdc/0x180 [ 3.640256] really_probe+0xe0/0x338 [ 3.640257] driver_probe_device+0x60/0xf8 [ 3.640259] __device_attach_driver+0x8c/0xd0 [ 3.640260] bus_for_each_drv+0x84/0xd8 [ 3.640261] __device_attach+0xe4/0x140 [ 3.640263] device_initial_probe+0x1c/0x28 [ 3.640265] bus_probe_device+0xa4/0xb0 [ 3.640266] deferred_probe_work_func+0x7c/0xb8 [ 3.640269] process_one_work+0x2c0/0x768 [ 3.640271] worker_thread+0x4c/0x498 [ 3.640272] kthread+0x14c/0x158 [ 3.640275] ret_from_fork+0x10/0x1c
Which seems to be due to the fact that after allocating the uap structure, nothing initializes the spinlock.
Its a little confusing, as uart_port_spin_lock_init() is one place where the lock is supposed to be initialized, but it has an exception for the case where the port is a console.
This makes it seem like a deeper fix is needed to properly register the console, but I'm not sure what that entails, and Andy suggested that this approach is less invasive.
Thus, this patch resolves the issue by initializing the spinlock in the driver, and resolves the resulting warning.
--- drivers/tty/serial/amba-pl011.c | 1 + 1 file changed, 1 insertion(+)
drivers/tty/serial/amba-pl011.c +1 -0
@@ -2585,6 +2585,7 @@ static int pl011_setup_port(struct device *dev, struct uart_amba_port *uap, uap->port.fifosize = uap->fifosize; uap->port.flags =UPF_BOOT_AUTOCONF ; uap->port.line = index; +spin_lock_init (&uap->port.lock); amba_ports[index] = uap;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 77/172 drivers: base: Fix NULL pointer exception in __platform_driver_probe() if a driver developer is foolish
In reply to Sasha LevinFrom: Kuppuswamy Sathyanarayanan <[email protected]>
[ Upstream commit 388bcc6ecc609fca1b4920de7dc3806c98ec535e ]
If platform bus driver registration is failed then, accessing platform bus spin lock (&drv->driver.bus->p->klist_drivers.k_lock) in __platform_driver_probe() without verifying the return value __platform_driver_register() can lead to NULL pointer exception.
So check the return value before attempting the spin lock.
One such example is below:
For a custom usecase, I have intentionally failed the platform bus registration and I expected all the platform device/driver registrations to fail gracefully. But I came across this panic issue.
[ 1.331067] BUG: kernel NULL pointer dereference, address: 00000000000000c8 [ 1.331118] #PF: supervisor write access in kernel mode [ 1.331163] #PF: error_code(0x0002) - not-present page [ 1.331208] PGD 0 P4D 0 [ 1.331233] Oops: 0002 [#1] PREEMPT SMP [ 1.331268] CPU: 3 PID: 1 Comm: swapper/0 Tainted: G W 5.6.0-00049-g670d35fb0144 #165 [ 1.331341] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015 [ 1.331406] RIP: 0010:_raw_spin_lock+0x15/0x30 [ 1.331588] RSP: 0000:ffffc9000001be70 EFLAGS: 00010246 [ 1.331632] RAX: 0000000000000000 RBX: 00000000000000c8 RCX: 0000000000000001 [ 1.331696] RDX: 0000000000000001 RSI: 0000000000000092 RDI: 0000000000000000 [ 1.331754] RBP: 00000000ffffffed R08: 0000000000000501 R09: 0000000000000001 [ 1.331817] R10: ffff88817abcc520 R11: 0000000000000670 R12: 00000000ffffffed [ 1.331881] R13: ffffffff82dbc268 R14: ffffffff832f070a R15: 0000000000000000 [ 1.331945] FS: 0000000000000000(0000) GS:ffff88817bd80000(0000) knlGS:0000000000000000 [ 1.332008] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1.332062] CR2: 00000000000000c8 CR3: 000000000681e001 CR4: 00000000003606e0 [ 1.332126] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 1.332189] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 1.332252] Call Trace: [ 1.332281] __platform_driver_probe+0x92/0xee [ 1.332323] ? rtc_dev_init+0x2b/0x2b [ 1.332358] cmos_init+0x37/0x67 [ 1.332396] do_one_initcall+0x7d/0x168 [ 1.332428] kernel_init_freeable+0x16c/0x1c9 [ 1.332473] ? rest_init+0xc0/0xc0 [ 1.332508] kernel_init+0x5/0x100 [ 1.332543] ret_from_fork+0x1f/0x30 [ 1.332579] CR2: 00000000000000c8 [ 1.332616] ---[ end trace 3bd87f12e9010b87 ]--- [ 1.333549] note: swapper/0[1] exited with preempt_count 1 [ 1.333592] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009 [ 1.333736] Kernel Offset: disabled
Note, this can only be triggered if a driver errors out from this call, which should never happen. If it does, the driver needs to be fixed.
--- drivers/base/platform.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/base/platform.c +2 -0
@@ -700,6 +700,8 @@ int __init_or_module __platform_driver_probe(struct platform_driver *drv,/* temporary section violation during probe() */ drv->probe = probe; retval = code =__platform_driver_register (drv, module); +if (retval) +return retval;/* * Fixup that section violation, being paranoid about code scanning
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 78/172 PCI: rcar: Fix incorrect programming of OB windows
In reply to Sasha LevinFrom: Andrew Murray <[email protected]>
[ Upstream commit 2b9f217433e31d125fb697ca7974d3de3ecc3e92 ]
The outbound windows (PCIEPAUR(x), PCIEPALR(x)) describe a mapping between a CPU address (which is determined by the window number 'x') and a programmed PCI address - Thus allowing the controller to translate CPU accesses into PCI accesses.
However the existing code incorrectly writes the CPU address - lets fix this by writing the PCI address instead.
For memory transactions, existing DT users describe a 1:1 identity mapping and thus this change should have no effect. However the same isn't true for I/O.
--- drivers/pci/controller/pcie-rcar.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-)
drivers/pci/controller/pcie-rcar.c +5 -4
@@ -335,11 +335,12 @@ static struct pci_ops rcar_pcie_ops = { };static void rcar_pcie_setup_window (int win,struct rcar_pcie *pcie, -struct resource *res) +struct resource_entry *window) {/* Setup PCIe address space mappings for each resource */ resource_size_t size;resource_size_t res_start; +struct resource *res = window->res;u32 mask;rcar_pci_write_reg (pcie,0x00000000 ,PCIEPTCTLR (win));
@@ -353,9 +354,9 @@ static void rcar_pcie_setup_window(int win, struct rcar_pcie *pcie,rcar_pci_write_reg (pcie, mask <<7 ,PCIEPAMR (win));if (res->flags &IORESOURCE_IO ) - res_start =pci_pio_to_address (res->start); + res_start =pci_pio_to_address (res->start) - window->offset;else - res_start = res->start; + res_start = res->start - window->offset;rcar_pci_write_reg (pcie,upper_32_bits (res_start),PCIEPAUR (win)); rcar_pci_write_reg(pcie, lower_32_bits(res_start) & ~0x7F,
@@ -384,7 +385,7 @@ static int rcar_pcie_setup(struct list_head *resource, struct rcar_pcie *pci)switch (resource_type (res)) {case IORESOURCE_IO :case IORESOURCE_MEM : -rcar_pcie_setup_window (i, pci, res); +rcar_pcie_setup_window (i, pci, win); i++;break ;case IORESOURCE_BUS :
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 79/172 PCI/ASPM: Allow ASPM on links to PCIe-to-PCI/PCI-X Bridges
In reply to Sasha LevinFrom: Kai-Heng Feng <[email protected]>
[ Upstream commit 66ff14e59e8a30690755b08bc3042359703fb07a ]
7d715a6c1ae5 ("PCI: add PCI Express ASPM support") added the ability for Linux to enable ASPM, but for some undocumented reason, it didn't enable ASPM on links where the downstream component is a PCIe-to-PCI/PCI-X Bridge.
Remove this exclusion so we can enable ASPM on these links.
The Dell OptiPlex 7080 mentioned in the bugzilla has a TI XIO2001 PCIe-to-PCI Bridge. Enabling ASPM on the link leading to it allows the Intel SoC to enter deeper Package C-states, which is a significant power savings.
[bhelgaas: commit log]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=207571
--- drivers/pci/pcie/aspm.c | 10 ---------- 1 file changed, 10 deletions(-)
drivers/pci/pcie/aspm.c +0 -10
@@ -633,16 +633,6 @@ static void pcie_aspm_cap_init(struct pcie_link_state *link, int blacklist)/* Setup initial capable state. Will be updated later */ link->aspm_capable = link->aspm_support; -/* -* If the downstream component has pci bridge function, don't -* do ASPM for now. -*/ -list_for_each_entry (child, &linkbus->devices, bus_list) { -if (pci_pcie_type (child) ==PCI_EXP_TYPE_PCI_BRIDGE ) { - link->aspm_disable =ASPM_STATE_ALL ; -break ; - } - }/* Get and check endpoint acceptable latencies */ list_for_each_entry (child, &linkbus->devices, bus_list) {
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 80/172 scsi: qla2xxx: Fix warning after FC target reset
In reply to Sasha LevinFrom: Viacheslav Dubeyko <[email protected]>
[ Upstream commit f839544ccff60cbe534282aac68858fc3fb278ca ]
Currently, FC target reset finishes with the warning message:
[84010.596893] ------------[ cut here ]------------
[84010.596917] WARNING: CPU: 238 PID: 279973 at ../drivers/scsi/qla2xxx/qla_target.c:6644 qlt_enable_vha+0x1d0/0x260 [qla2xxx]
[84010.596918] Modules linked in: vrf af_packet 8021q garp mrp stp llc netlink_diag target_tatlin_tblock(OEX) dm_ec(OEX) ttln_rdma(OEX) dm_frontend(OEX) nvme_rdma nvmet tcm_qla2xxx iscsi_target_mod target_core_mod at24 nvmem_core pnv_php ipmi_watchdog ipmi_ssif vmx_crypto gf128mul crct10dif_vpmsum qla2xxx rpcrdma nvme_fc powernv_flash(X) nvme_fabrics uio_pdrv_genirq mtd rtc_opal(X) ibmpowernv(X) opal_prd(X) uio scsi_transport_fc i2c_opal(X) ses enclosure ipmi_poweroff ast i2c_algo_bit ttm bmc_mcu(OEX) drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops drm drm_panel_orientation_quirks agpgart nfsd auth_rpcgss nfs_acl ipmi_powernv(X) lockd ipmi_devintf ipmi_msghandler grace dummy ext4 crc16 jbd2 mbcache sd_mod rdma_ucm ib_iser rdma_cm ib_umad iw_cm ib_ipoib libiscsi scsi_transport_iscsi ib_cm
[84010.596975] configfs mlx5_ib ib_uverbs ib_core mlx5_core crc32c_vpmsum xhci_pci xhci_hcd mpt3sas(OEX) tg3 usbcore mlxfw tls raid_class libphy scsi_transport_sas devlink ptp pps_core nvme nvme_core sunrpc dm_mirror dm_region_hash dm_log sg dm_multipath dm_mod scsi_dh_rdac scsi_dh_emc scsi_dh_alua scsi_mod autofs4
[84010.597001] Supported: Yes, External
[84010.597004] CPU: 238 PID: 279973 Comm: bash Tainted: G OE 4.12.14-197.29-default #1 SLE15-SP1
[84010.597006] task: c000000a104c0000 task.stack: c000000b52188000
[84010.597007] NIP: d00000001ffd7f78 LR: d00000001ffd7f6c CTR: c0000000001676c0
[84010.597008] REGS: c000000b5218b910 TRAP: 0700 Tainted: G OE (4.12.14-197.29-default)
[84010.597008] MSR: 900000010282b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE,TM[E]>
[84010.597015] CR: 48242424 XER: 00000000
[84010.597016] CFAR: d00000001ff45d08 SOFTE: 1
GPR00: d00000001ffd7f6c c000000b5218bb90 d00000002001b228 0000000000000102
GPR04: 0000000000000001 0000000000000001 00013d91ed0a5e2d 0000000000000000
GPR08: c000000007793300 0000000000000000 0000000000000000 c000000a086e7818
GPR12: 0000000000002200 c000000007793300 0000000000000000 000000012bc937c0
GPR16: 000000012bbf7ed0 0000000000000000 000000012bc3dd10 0000000000000000
GPR20: 000000012bc4db28 0000010036442810 000000012bc97828 000000012bc96c70
GPR24: 00000100365b1550 0000000000000000 00000100363f3d80 c000000be20d3080
GPR28: c000000bda7eae00 c000000be20db7e8 c000000be20d3778 c000000be20db7e8
[84010.597042] NIP [d00000001ffd7f78] qlt_enable_vha+0x1d0/0x260 [qla2xxx]
[84010.597051] LR [d00000001ffd7f6c] qlt_enable_vha+0x1c4/0x260 [qla2xxx]
[84010.597051] Call Trace:
[84010.597061] [c000000b5218bb90] [d00000001ffd7f6c] qlt_enable_vha+0x1c4/0x260 [qla2xxx] (unreliable)
[84010.597064] [c000000b5218bc20] [d000000009820b6c] tcm_qla2xxx_tpg_enable_store+0xc4/0x130 [tcm_qla2xxx]
[84010.597067] [c000000b5218bcb0] [d0000000185d0e68] configfs_write_file+0xd0/0x190 [configfs]
[84010.597072] [c000000b5218bd00] [c0000000003d0edc] __vfs_write+0x3c/0x1e0
[84010.597074] [c000000b5218bd90] [c0000000003d2ea8] vfs_write+0xd8/0x220
[84010.597076] [c000000b5218bde0] [c0000000003d4ddc] SyS_write+0x6c/0x110
[84010.597079] [c000000b5218be30] [c00000000000b188] system_call+0x3c/0x130
[84010.597080] Instruction dump:
[84010.597082] 7d0050a8 7d084b78 7d0051ad 40c2fff4 7fa3eb78 4bf73965 60000000 7fa3eb78
[84010.597086] 4bf6dcd9 60000000 2fa30000 419eff40 <0fe00000> 4bffff38 e95f0058 a12a0180
[84010.597090] ---[ end trace e32abaf6e6fee826 ]---To reproduce:
echo 0x7fffffff > /sys/module/qla2xxx/parameters/logging modprobe target_core_mod
modprobe tcm_qla2xxx
mkdir /sys/kernel/config/target/qla2xxx
mkdir /sys/kernel/config/target/qla2xxx/<port-name>
mkdir /sys/kernel/config/target/qla2xxx/<port-name>/tpgt_1 echo 1 > /sys/kernel/config/target/qla2xxx/<port-name>/tpgt_1/enable echo 0 > /sys/kernel/config/target/qla2xxx/<port-name>/tpgt_1/enable echo 1 > /sys/kernel/config/target/qla2xxx/<port-name>/tpgt_1/enable
SYSTEM START
kernel: pid 327:drivers/scsi/qla2xxx/qla_init.c:2174 qla2x00_initialize_adapter(): vha->flags.online 0x0 <...>
kernel: pid 327:drivers/scsi/qla2xxx/qla_os.c:3444 qla2x00_probe_one(): vha->flags.online 0x1
echo 1 > /sys/kernel/config/target/qla2xxx/21:00:00:24:ff:86:a6:2a/tpgt_1/enable
kernel: pid 348:drivers/scsi/qla2xxx/qla_init.c:6641 qla2x00_abort_isp_cleanup(): vha->flags.online 0x0, ISP_ABORT_NEEDED 0x0 <...>
kernel: pid 348:drivers/scsi/qla2xxx/qla_init.c:6998 qla2x00_restart_isp(): vha->flags.online 0x0
echo 0 > /sys/kernel/config/target/qla2xxx/21:00:00:24:ff:86:a6:2a/tpgt_1/enable
kernel: pid 348:drivers/scsi/qla2xxx/qla_init.c:6641 qla2x00_abort_isp_cleanup(): vha->flags.online 0x0, ISP_ABORT_NEEDED 0x0 <...>
kernel: pid 1404:drivers/scsi/qla2xxx/qla_os.c:1107 qla2x00_wait_for_hba_online(): base_vha->flags.online 0x0
echo 1 > /sys/kernel/config/target/qla2xxx/21:00:00:24:ff:86:a6:2a/tpgt_1/enable
kernel: pid 1404:drivers/scsi/qla2xxx/qla_os.c:1107 qla2x00_wait_for_hba_online(): base_vha->flags.online 0x0
kernel: -----------[ cut here ]-----------
kernel: WARNING: CPU: 1 PID: 1404 at drivers/scsi/qla2xxx/qla_target.c:6654 qlt_enable_vha+0x1e0/0x280 [qla2xxx]
The issue happens because no real ISP reset is executed. The qla2x00_abort_isp(scsi_qla_host_t *vha) function expects that vha->flags.online will be not zero for ISP reset procedure. This patch sets vha->flags.online to 1 before calling ->abort_isp() for starting the ISP reset.
--- drivers/scsi/qla2xxx/qla_os.c | 1 + 1 file changed, 1 insertion(+)
drivers/scsi/qla2xxx/qla_os.c +1 -0
@@ -6085,6 +6085,7 @@ qla2x00_do_dpc(void *data)if (do_reset && !(test_and_set_bit (ABORT_ISP_ACTIVE , &base_vha->dpc_flags))) { + base_vha->flags.online =1 ;ql_dbg (ql_dbg_dpc, base_vha,0x4007 ,"ISP abort scheduled.\n" );if (ha->isp_ops->abort_isp (base_vha)) {
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 81/172 power: supply: lp8788: Fix an error handling path in 'lp8788_charger_probe()'
In reply to Sasha LevinFrom: Christophe JAILLET <[email protected]>
[ Upstream commit 934ed3847a4ebc75b655659c4d2349ba4337941c ]
In the probe function, in case of error, resources allocated in 'lp8788_setup_adc_channel()' must be released.
This can be achieved easily by using the devm_ variant of 'iio_channel_get()'.
This has the extra benefit to simplify the remove function and to axe the 'lp8788_release_adc_channel()' function which is now useless.
--- drivers/power/supply/lp8788-charger.c | 18 ++---------------- 1 file changed, 2 insertions(+), 16 deletions(-)
drivers/power/supply/lp8788-charger.c +2 -16
@@ -600,27 +600,14 @@ static void lp8788_setup_adc_channel(struct device *dev,return ;/* ADC channel for battery voltage */ - chan =iio_channel_get (dev, pdata->adc_vbatt); + chan =devm_iio_channel_get (dev, pdata->adc_vbatt); pchg->chan[LP8788_VBATT ] =IS_ERR (chan) ?NULL : chan;/* ADC channel for battery temperature */ - chan =iio_channel_get (dev, pdata->adc_batt_temp); + chan =devm_iio_channel_get (dev, pdata->adc_batt_temp); pchg->chan[LP8788_BATT_TEMP ] =IS_ERR (chan) ?NULL : chan; } -static void lp8788_release_adc_channel (struct lp8788_charger *pchg) -{ -int i; - -for (i =0 ; i <LP8788_NUM_CHG_ADC ; i++) { -if (!pchg->chan[i]) -continue ; - -iio_channel_release (pchg->chan[i]); - pchg->chan[i] =NULL ; - } -} -static ssize_t lp8788_show_charger_status (struct device *dev,struct device_attribute *attr,char *buf) {
@@ -747,7 +734,6 @@ static int lp8788_charger_remove(struct platform_device *pdev)lp8788_irq_unregister (pdev, pchg);sysfs_remove_group (&pdev->dev.kobj, &lp8788_attr_group);lp8788_psy_unregister (pchg); -lp8788_release_adc_channel (pchg);return 0 ; }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 82/172 power: supply: smb347-charger: IRQSTAT_D is volatile
In reply to Sasha LevinFrom: Dmitry Osipenko <[email protected]>
[ Upstream commit c32ea07a30630ace950e07ffe7a18bdcc25898e1 ]
Fix failure when USB cable is connected:
smb347 2-006a: reading IRQSTAT_D failed
--- drivers/power/supply/smb347-charger.c | 1 + 1 file changed, 1 insertion(+)
drivers/power/supply/smb347-charger.c +1 -0
@@ -1141,6 +1141,7 @@ static bool smb347_volatile_reg(struct device *dev, unsigned int reg)switch (reg) {case IRQSTAT_A :case IRQSTAT_C : +case IRQSTAT_D :case IRQSTAT_E :case IRQSTAT_F :case STAT_A :
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 83/172 scsi: mpt3sas: Fix double free warnings
In reply to Sasha LevinFrom: Suganath Prabu S <[email protected]>
[ Upstream commit cbbfdb2a2416c9f0cde913cf09670097ac281282 ]
Fix following warning from Smatch static analyser:
drivers/scsi/mpt3sas/mpt3sas_base.c:5256 _base_allocate_memory_pools()
warn: 'ioc->hpr_lookup' double freed
drivers/scsi/mpt3sas/mpt3sas_base.c:5256 _base_allocate_memory_pools()
warn: 'ioc->internal_lookup' double freed
--- drivers/scsi/mpt3sas/mpt3sas_base.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/scsi/mpt3sas/mpt3sas_base.c +2 -0
@@ -4284,7 +4284,9 @@ _base_release_memory_pools(struct MPT3SAS_ADAPTER *ioc) }kfree (ioc->hpr_lookup); + ioc->hpr_lookup =NULL ;kfree (ioc->internal_lookup); + ioc->internal_lookup =NULL ;if (ioc->chain_lookup) {for (i =0 ; i < ioc->scsiio_depth; i++) { for (j = ioc->chains_per_prp_buffer;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 84/172 pinctrl: rockchip: fix memleak in rockchip_dt_node_to_map
In reply to Sasha LevinFrom: Dafna Hirschfeld <[email protected]>
[ Upstream commit d7faa8ffb6be57bf8233a4b5a636d76b83c51ce7 ]
In function rockchip_dt_node_to_map, a new_map variable is allocated by:
new_map = devm_kcalloc(pctldev->dev, map_num, sizeof(*new_map),
GFP_KERNEL);
This uses devres and attaches new_map to the pinctrl driver. This cause a leak since new_map is not released when the probed driver is removed. Fix it by using kcalloc to allocate new_map and free it in rockchip_dt_free_map
--- drivers/pinctrl/pinctrl-rockchip.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/pinctrl/pinctrl-rockchip.c +4 -3
@@ -507,8 +507,8 @@ static int rockchip_dt_node_to_map(struct pinctrl_dev *pctldev, } map_num += grp->npins; - new_map =devm_kcalloc (pctldev->dev, map_num,sizeof (*new_map), -GFP_KERNEL ); + + new_map =kcalloc (map_num,sizeof (*new_map),GFP_KERNEL );if (!new_map)return -ENOMEM ;
@@ -518,7 +518,7 @@ static int rockchip_dt_node_to_map(struct pinctrl_dev *pctldev,/* create mux map */ parent =of_get_parent (np);if (!parent) { -devm_kfree (pctldev->dev, new_map); +kfree (new_map);return -EINVAL ; } new_map[0 ].type =PIN_MAP_TYPE_MUX_GROUP ;
@@ -545,6 +545,7 @@ static int rockchip_dt_node_to_map(struct pinctrl_dev *pctldev,static void rockchip_dt_free_map (struct pinctrl_dev *pctldev,struct pinctrl_map *map,unsigned num_maps) { +kfree (map); }static const struct pinctrl_ops rockchip_pctrl_ops = {
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 85/172 dlm: remove BUG() before panic()
In reply to Sasha LevinFrom: Arnd Bergmann <[email protected]>
[ Upstream commit fe204591cc9480347af7d2d6029b24a62e449486 ]
Building a kernel with clang sometimes fails with an objtool error in dlm:
fs/dlm/lock.o: warning: objtool: revert_lock_pc()+0xbd: can't find jump dest instruction at .text+0xd7fc
The problem is that BUG() never returns and the compiler knows that anything after it is unreachable, however the panic still emits some code that does not get fully eliminated.
Having both BUG() and panic() is really pointless as the BUG() kills the current process and the subsequent panic() never hits. In most cases, we probably don't really want either and should replace the DLM_ASSERT() statements with WARN_ON(), as has been done for some of them.
Remove the BUG() here so the user at least sees the panic message and we can reliably build randconfig kernels.
--- fs/dlm/dlm_internal.h | 1 - 1 file changed, 1 deletion(-)
fs/dlm/dlm_internal.h +0 -1
@@ -99,7 +99,6 @@ do { \ __LINE__, __FILE__, #x, jiffies); \ {do} \ printk("\n"); \ - BUG(); \ panic("DLM: Record message above and reboot.\n"); \ } \ }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 86/172 clk: ti: composite: fix memory leak
In reply to Sasha LevinFrom: Tero Kristo <[email protected]>
[ Upstream commit c7c1cbbc9217ebb5601b88d138d4a5358548de9d ]
The parent_names is never released for a component clock definition, causing some memory leak. Fix by releasing it once it is no longer needed.
--- drivers/clk/ti/composite.c | 1 + 1 file changed, 1 insertion(+)
drivers/clk/ti/composite.c +1 -0
@@ -196,6 +196,7 @@ static void __init _register_composite(void *user,if (!cclk->comp_clks[i])continue ;list_del (&cclk->comp_clks[i]->link); +kfree (cclk->comp_clks[i]->parent_names);kfree (cclk->comp_clks[i]); }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 87/172 PCI: Fix pci_register_host_bridge() device_register() error handling
In reply to Sasha LevinFrom: Rob Herring <[email protected]>
[ Upstream commit 1b54ae8327a4d630111c8d88ba7906483ec6010b ]
If device_register() has an error, we should bail out of pci_register_host_bridge() rather than continuing on.
--- drivers/pci/probe.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/pci/probe.c +3 -2
@@ -818,9 +818,10 @@ static int pci_register_host_bridge(struct pci_host_bridge *bridge) goto free; err =device_register (&bridge->dev); -if (err) +if (err) {put_device (&bridge->dev); - + goto free; + } bus->bridge =get_device (&bridge->dev);device_enable_async_suspend (bus->bridge);pci_set_bus_of_node (bus);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 88/172 powerpc/64: Don't initialise init_task->thread.regs
In reply to Sasha LevinFrom: Michael Ellerman <[email protected]>
[ Upstream commit 7ffa8b7dc11752827329e4e84a574ea6aaf24716 ]
Aneesh increased the size of struct pt_regs by 16 bytes and started seeing this WARN_ON:
smp: Bringing up secondary CPUs ...
------------[ cut here ]------------ WARNING: CPU: 0 PID: 0 at arch/powerpc/kernel/process.c:455 giveup_all+0xb4/0x110 Modules linked in: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.7.0-rc2-gcc-8.2.0-1.g8f6a41f-default+ #318 NIP: c00000000001a2b4 LR: c00000000001a29c CTR: c0000000031d0000 REGS: c0000000026d3980 TRAP: 0700 Not tainted (5.7.0-rc2-gcc-8.2.0-1.g8f6a41f-default+) MSR: 800000000282b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 48048224 XER: 00000000 CFAR: c000000000019cc8 IRQMASK: 1 GPR00: c00000000001a264 c0000000026d3c20 c0000000026d7200 800000000280b033 GPR04: 0000000000000001 0000000000000000 0000000000000077 30206d7372203164 GPR08: 0000000000002000 0000000002002000 800000000280b033 3230303030303030 GPR12: 0000000000008800 c0000000031d0000 0000000000800050 0000000002000066 GPR16: 000000000309a1a0 000000000309a4b0 000000000309a2d8 000000000309a890 GPR20: 00000000030d0098 c00000000264da40 00000000fd620000 c0000000ff798080 GPR24: c00000000264edf0 c0000001007469f0 00000000fd620000 c0000000020e5e90 GPR28: c00000000264edf0 c00000000264d200 000000001db60000 c00000000264d200 NIP [c00000000001a2b4] giveup_all+0xb4/0x110 LR [c00000000001a29c] giveup_all+0x9c/0x110 Call Trace: [c0000000026d3c20] [c00000000001a264] giveup_all+0x64/0x110 (unreliable) [c0000000026d3c90] [c00000000001ae34] __switch_to+0x104/0x480 [c0000000026d3cf0] [c000000000e0b8a0] __schedule+0x320/0x970 [c0000000026d3dd0] [c000000000e0c518] schedule_idle+0x38/0x70 [c0000000026d3df0] [c00000000019c7c8] do_idle+0x248/0x3f0 [c0000000026d3e70] [c00000000019cbb8] cpu_startup_entry+0x38/0x40 [c0000000026d3ea0] [c000000000011bb0] rest_init+0xe0/0xf8 [c0000000026d3ed0] [c000000002004820] start_kernel+0x990/0x9e0 [c0000000026d3f90] [c00000000000c49c] start_here_common+0x1c/0x400
Which was unexpected. The warning is checking the thread.regs->msr value of the task we are switching from:
usermsr = tsk->thread.regs->msr; ... WARN_ON((usermsr & MSR_VSX) && !((usermsr & MSR_FP) && (usermsr & MSR_VEC)));
ie. if MSR_VSX is set then both of MSR_FP and MSR_VEC are also set.
Dumping tsk->thread.regs->msr we see that it's: 0x1db60000
Which is not a normal looking MSR, in fact the only valid bit is MSR_VSX, all the other bits are reserved in the current definition of the MSR.
We can see from the oops that it was swapper/0 that we were switching from when we hit the warning, ie. init_task. So its thread.regs points to the base (high addresses) in init_stack.
Dumping the content of init_task->thread.regs, with the members of pt_regs annotated (the 16 bytes larger version), we see:
0000000000000000 c000000002780080 gpr[0] gpr[1] 0000000000000000 c000000002666008 gpr[2] gpr[3] c0000000026d3ed0 0000000000000078 gpr[4] gpr[5] c000000000011b68 c000000002780080 gpr[6] gpr[7] 0000000000000000 0000000000000000 gpr[8] gpr[9] c0000000026d3f90 0000800000002200 gpr[10] gpr[11] c000000002004820 c0000000026d7200 gpr[12] gpr[13] 000000001db60000 c0000000010aabe8 gpr[14] gpr[15] c0000000010aabe8 c0000000010aabe8 gpr[16] gpr[17] c00000000294d598 0000000000000000 gpr[18] gpr[19] 0000000000000000 0000000000001ff8 gpr[20] gpr[21] 0000000000000000 c00000000206d608 gpr[22] gpr[23] c00000000278e0cc 0000000000000000 gpr[24] gpr[25] 000000002fff0000 c000000000000000 gpr[26] gpr[27] 0000000002000000 0000000000000028 gpr[28] gpr[29] 000000001db60000 0000000004750000 gpr[30] gpr[31] 0000000002000000 000000001db60000 nip msr 0000000000000000 0000000000000000 orig_r3 ctr c00000000000c49c 0000000000000000 link xer 0000000000000000 0000000000000000 ccr softe 0000000000000000 0000000000000000 trap dar 0000000000000000 0000000000000000 dsisr result 0000000000000000 0000000000000000 ppr kuap 0000000000000000 0000000000000000 pad[2] pad[3]
This looks suspiciously like stack frames, not a pt_regs. If we look closely we can see return addresses from the stack trace above, c000000002004820 (start_kernel) and c00000000000c49c (start_here_common).
init_task->thread.regs is setup at build time in processor.h:
#define INIT_THREAD { \
.ksp = INIT_SP, \
.regs = (struct pt_regs *)INIT_SP - 1, /* XXX bogus, I think */ \The early boot code where we setup the initial stack is:
LOAD_REG_ADDR(r3,init_thread_union)
/* set up a stack pointer */
LOAD_REG_IMMEDIATE(r1,THREAD_SIZE)
add r1,r3,r1
li r0,0
stdu r0,-STACK_FRAME_OVERHEAD(r1)
Which creates a stack frame of size 112 bytes (STACK_FRAME_OVERHEAD). Which is far too small to contain a pt_regs.
So the result is init_task->thread.regs is pointing at some stack frames on the init stack, not at a pt_regs.
We have gotten away with this for so long because with pt_regs at its current size the MSR happens to point into the first frame, at a location that is not written to by the early asm. With the 16 byte expansion the MSR falls into the second frame, which is used by the compiler, and collides with a saved register that tends to be non-zero.
As far as I can see this has been wrong since the original merge of 64-bit ppc support, back in 2002.
Conceptually swapper should have no regs, it never entered from userspace, and in fact that's what we do on 32-bit. It's also presumably what the "bogus" comment is referring to.
So I think the right fix is to just not-initialise regs at all. I'm slightly worried this will break some code that isn't prepared for a NULL regs, but we'll have to see.
Remove the comment in head_64.S which refers to us setting up the regs (even though we never did), and is otherwise not really accurate any more.
--- arch/powerpc/include/asm/processor.h | 1 - arch/powerpc/kernel/head_64.S | 9 +-------- 2 files changed, 1 insertion(+), 9 deletions(-)
arch/powerpc/include/asm/processor.h +0 -1
@@ -386,7 +386,6 @@ struct thread_struct {#else #define INIT_THREAD { \ .ksp = INIT_SP, \ - .regs = (struct pt_regs *)INIT_SP - 1, /* XXX bogus, I think */ \ .addr_limit = KERNEL_DS, \ .fpexc_mode = 0, \ .ppr = INIT_PPR, \
arch/powerpc/kernel/head_64.S +1 -8
@@ -950,15 +950,8 @@ start_here_multiplatform: std r0,0(r4) #endif - /* The following gets the stack set up with the regs */ - /* pointing to the real addr of the kernel stack. This is */ - /* all done to support the C function call below which sets */ - /* up the htab. This is done because we have relocated the */ - /* kernel but are still running in real mode. */ - - LOAD_REG_ADDR(r3,init_thread_union) - /* set up a stack pointer */ + LOAD_REG_ADDR(r3,init_thread_union) LOAD_REG_IMMEDIATE(r1,THREAD_SIZE) add r1,r3,r1 li r0,0
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 89/172 tty: n_gsm: Fix SOF skipping
In reply to Sasha LevinFrom: Gregory CLEMENT <[email protected]>
[ Upstream commit 84d6f81c1fb58b56eba81ff0a36cf31946064b40 ]
For at least some modems like the TELIT LE910, skipping SOF makes transfers blocking indefinitely after a short amount of data transferred.
Given the small improvement provided by skipping the SOF (just one byte on about 100 bytes), it seems better to completely remove this "feature" than make it optional.
--- drivers/tty/n_gsm.c | 8 +------- 1 file changed, 1 insertion(+), 7 deletions(-)
drivers/tty/n_gsm.c +1 -7
@@ -669,7 +669,6 @@ static void gsm_data_kick(struct gsm_mux *gsm) {struct gsm_msg *msg, *nmsg;int len; -int skip_sof =0 ;list_for_each_entry_safe (msg, nmsg, &gsm->tx_list, list) {if (gsm->constipated && msg->addr)
@@ -691,15 +690,10 @@ static void gsm_data_kick(struct gsm_mux *gsm)print_hex_dump_bytes ("gsm_data_kick: " ,DUMP_PREFIX_OFFSET , gsm->txframe, len); - -if (gsm->output (gsm, gsm->txframe + skip_sof, - len - skip_sof) <0 ) +if (gsm->output (gsm, gsm->txframe, len) <0 )break ;/* FIXME: Can eliminate one SOF in many more cases */ gsm->tx_bytes -= msg->len; -/* For a burst of frames skip the extra SOF within the -burst */ - skip_sof =1 ;list_del (&msg->list);kfree (msg);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 90/172 tty: n_gsm: Fix waking up upper tty layer when room available
In reply to Sasha LevinFrom: Gregory CLEMENT <[email protected]>
[ Upstream commit 01dbb362f0a114fbce19c8abe4cd6f4710e934d5 ]
Warn the upper layer when n_gms is ready to receive data again. Without this the associated virtual tty remains blocked indefinitely.
--- drivers/tty/n_gsm.c | 26 ++++++++++++++++++++++---- 1 file changed, 22 insertions(+), 4 deletions(-)
drivers/tty/n_gsm.c +22 -4
@@ -665,7 +665,7 @@ static struct gsm_msg *gsm_data_alloc(struct gsm_mux *gsm, u8 addr, int len,* FIXME: lock against link layer control transmissions */ -static void gsm_data_kick (struct gsm_mux *gsm) +static void gsm_data_kick (struct gsm_mux *gsm,struct gsm_dlci *dlci) {struct gsm_msg *msg, *nmsg;int len;
@@ -697,6 +697,24 @@ static void gsm_data_kick(struct gsm_mux *gsm)list_del (&msg->list);kfree (msg); + +if (dlci) { +tty_port_tty_wakeup (&dlci->port); + }else { +int i =0 ; + +for (i =0 ; i <NUM_DLCI ; i++) { +struct gsm_dlci *dlci; + + dlci = gsm->dlci[i]; +if (dlci ==NULL ) { + i++; +continue ; + } + +tty_port_tty_wakeup (&dlci->port); + } + } } }
@@ -748,7 +766,7 @@ static void __gsm_data_queue(struct gsm_dlci *dlci, struct gsm_msg *msg)/* Add to the actual output queue */ list_add_tail (&msg->list, &gsm->tx_list); gsm->tx_bytes += msg->len; -gsm_data_kick (gsm); +gsm_data_kick (gsm, dlci); }/**
@@ -1209,7 +1227,7 @@ static void gsm_control_message(struct gsm_mux *gsm, unsigned int command,gsm_control_reply (gsm,CMD_FCON ,NULL ,0 );/* Kick the link in case it is idling */ spin_lock_irqsave (&gsm->tx_lock, flags); -gsm_data_kick (gsm); +gsm_data_kick (gsm,NULL );spin_unlock_irqrestore (&gsm->tx_lock, flags);break ;case CMD_FCOFF :
@@ -2406,7 +2424,7 @@ static void gsmld_write_wakeup(struct tty_struct *tty)/* Queue poll */ clear_bit (TTY_DO_WRITE_WAKEUP , &tty->flags);spin_lock_irqsave (&gsm->tx_lock, flags); -gsm_data_kick (gsm); +gsm_data_kick (gsm,NULL );if (gsm->tx_bytes <TX_THRESH_LO ) {gsm_dlci_data_sweep (gsm); }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 91/172 HID: Add quirks for Trust Panora Graphic Tablet
In reply to Sasha LevinFrom: Cristian Klein <[email protected]>
[ Upstream commit fb68ada81e65d593b51544fa43c284322107a742 ]
The Trust Panora Graphic Tablet has two interfaces. Interface zero reports pen movement, pen pressure and pen buttons. Interface one reports tablet buttons and tablet scroll. Both use the mouse protocol.
Without these quirks, libinput gets confused about what device it talks to.
For completeness, here is the usbhid-dump:
``` $ sudo usbhid-dump -d 145f:0212 003:013:001:DESCRIPTOR 1588949402.559961 05 0D 09 01 A1 01 85 07 A1 02 09 00 75 08 95 07 81 02 C0 C0 09 0E A1 01 85 05 09 23 A1 02 09 52 09 53 25 0A 75 08 95 02 B1 02 C0 C0 05 0C 09 36 A1 00 85 06 05 09 19 01 29 20 15 00 25 01 95 20 75 01 81 02 C0 003:013:000:DESCRIPTOR 1588949402.563942 05 01 09 02 A1 01 85 08 09 01 A1 00 05 09 19 01 29 03 15 00 25 01 95 03 75 01 81 02 95 05 81 01 05 01 09 30 09 31 09 38 09 00 15 81 25 7F 75 08 95 04 81 06 C0 C0 05 01 09 02 A1 01 85 09 09 01 A1 00 05 09 19 01 29 03 15 00 25 01 95 03 75 01 81 02 95 05 81 01 05 01 09 30 09 31 26 FF 7F 95 02 75 10 81 02 05 0D 09 30 26 FF 03 95 01 75 10 81 02 C0 C0 05 01 09 00 A1 01 85 04 A1 00 26 FF 00 09 00 75 08 95 07 B1 02 C0 C0 ```
--- drivers/hid/hid-ids.h | 3 +++ drivers/hid/hid-quirks.c | 1 + 2 files changed, 4 insertions(+)
drivers/hid/hid-ids.h +3 -0
@@ -1121,6 +1121,9 @@#define USB_DEVICE_ID_TPV_OPTICAL_TOUCHSCREEN_8882 0x8882#define USB_DEVICE_ID_TPV_OPTICAL_TOUCHSCREEN_8883 0x8883 +#define USB_VENDOR_ID_TRUST 0x145f +#define USB_DEVICE_ID_TRUST_PANORA_TABLET 0x0212 +#define USB_VENDOR_ID_TURBOX 0x062a#define USB_DEVICE_ID_TURBOX_KEYBOARD 0x0201#define USB_DEVICE_ID_ASUS_MD_5110 0x5110
drivers/hid/hid-quirks.c +1 -0
@@ -168,6 +168,7 @@ static const struct hid_device_id hid_quirks[] = { { HID_USB_DEVICE(USB_VENDOR_ID_TOUCHPACK, USB_DEVICE_ID_TOUCHPACK_RTS), HID_QUIRK_MULTI_INPUT }, { HID_USB_DEVICE(USB_VENDOR_ID_TPV, USB_DEVICE_ID_TPV_OPTICAL_TOUCHSCREEN_8882), HID_QUIRK_NOGET }, { HID_USB_DEVICE(USB_VENDOR_ID_TPV, USB_DEVICE_ID_TPV_OPTICAL_TOUCHSCREEN_8883), HID_QUIRK_NOGET }, + { HID_USB_DEVICE(USB_VENDOR_ID_TRUST, USB_DEVICE_ID_TRUST_PANORA_TABLET), HID_QUIRK_MULTI_INPUT | HID_QUIRK_HIDINPUT_FORCE }, { HID_USB_DEVICE(USB_VENDOR_ID_TURBOX, USB_DEVICE_ID_TURBOX_KEYBOARD), HID_QUIRK_NOGET }, { HID_USB_DEVICE(USB_VENDOR_ID_UCLOGIC, USB_DEVICE_ID_UCLOGIC_TABLET_KNA5), HID_QUIRK_MULTI_INPUT }, { HID_USB_DEVICE(USB_VENDOR_ID_UCLOGIC, USB_DEVICE_ID_UCLOGIC_TABLET_TWA60), HID_QUIRK_MULTI_INPUT },
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 92/172 ipmi: use vzalloc instead of kmalloc for user creation
In reply to Sasha LevinFrom: Feng Tang <[email protected]>
[ Upstream commit 7c47a219b95d0e06b5ef5fcc7bad807895015eac ]
We met mulitple times of failure of staring bmc-watchdog, due to the runtime memory allocation failure of order 4.
bmc-watchdog: page allocation failure: order:4, mode:0x40cc0(GFP_KERNEL|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0-1
CPU: 1 PID: 2571 Comm: bmc-watchdog Not tainted 5.5.0-00045-g7d6bb61d6188c #1
Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.00.01.0015.110720180833 11/07/2018
Call Trace:
dump_stack+0x66/0x8b
warn_alloc+0xfe/0x160
__alloc_pages_slowpath+0xd3e/0xd80
__alloc_pages_nodemask+0x2f0/0x340
kmalloc_order+0x18/0x70
kmalloc_order_trace+0x1d/0xb0
ipmi_create_user+0x55/0x2c0 [ipmi_msghandler]
ipmi_open+0x72/0x110 [ipmi_devintf]
chrdev_open+0xcb/0x1e0
do_dentry_open+0x1ce/0x380
path_openat+0x305/0x14f0
do_filp_open+0x9b/0x110
do_sys_open+0x1bd/0x250
do_syscall_64+0x5b/0x1f0
entry_SYSCALL_64_after_hwframe+0x44/0xa9Using vzalloc/vfree for creating ipmi_user heals the problem
Thanks to Stephen Rothwell for finding the vmalloc.h inclusion issue.
--- drivers/char/ipmi/ipmi_msghandler.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/char/ipmi/ipmi_msghandler.c +4 -3
@@ -30,6 +30,7 @@#include <linux/workqueue.h> #include <linux/uuid.h> #include <linux/nospec.h> +#include <linux/vmalloc.h> #define PFX "IPMI message handler: "
@@ -1089,7 +1090,7 @@ static void free_user_work(struct work_struct *work) remove_work);cleanup_srcu_struct (&user->release_barrier); -kfree (user); +vfree (user); } int ipmi_create_user(unsigned int if_num,
@@ -1121,7 +1122,7 @@ int ipmi_create_user(unsigned int if_num,if (rv)return rv; - new_user =kmalloc (sizeof (*new_user),GFP_KERNEL ); + new_user =vzalloc (sizeof (*new_user));if (!new_user)return -ENOMEM ;
@@ -1170,7 +1171,7 @@ int ipmi_create_user(unsigned int if_num, out_kfree:srcu_read_unlock (&ipmi_interfaces_srcu, index); -kfree (new_user); +vfree (new_user);return rv; }EXPORT_SYMBOL (ipmi_create_user);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 93/172 powerpc/pseries/ras: Fix FWNMI_VALID off by one
In reply to Sasha LevinFrom: Nicholas Piggin <[email protected]>
[ Upstream commit deb70f7a35a22dffa55b2c3aac71bc6fb0f486ce ]
This was discovered developing qemu fwnmi sreset support. This off-by-one bug means the last 16 bytes of the rtas area can not be used for a 16 byte save area.
It's not a serious bug, and QEMU implementation has to retain a workaround for old kernels, but it's good to tighten it.
--- arch/powerpc/platforms/pseries/ras.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
arch/powerpc/platforms/pseries/ras.c +3 -2
@@ -328,10 +328,11 @@ static irqreturn_t ras_error_interrupt(int irq, void *dev_id)/* * Some versions of FWNMI place the buffer inside the 4kB page starting at * 0x7000. Other versions place it inside the rtas buffer. We check both. +* Minimum size of the buffer is 16 bytes. */ #define VALID_FWNMI_BUFFER (A ) \ - ((((A) >= 0x7000) && ((A) < 0x7ff0)) || \ - (((A) >= rtas.base) && ((A) < (rtas.base + rtas.size - 16)))) + ((((A) >= 0x7000) && ((A) <= 0x8000 - 16)) || \ + (((A) >= rtas.base) && ((A) <= (rtas.base + rtas.size - 16))))static inline struct rtas_error_log *fwnmi_get_errlog (void ) {
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 94/172 powerpc/ps3: Fix kexec shutdown hang
In reply to Sasha LevinFrom: Geoff Levand <[email protected]>
[ Upstream commit 126554465d93b10662742128918a5fc338cda4aa ]
The ps3_mm_region_destroy() and ps3_mm_vas_destroy() routines are called very late in the shutdown via kexec's mmu_cleanup_all routine. By the time mmu_cleanup_all runs it is too late to use udbg_printf, and calling it will cause PS3 systems to hang.
Remove all debugging statements from ps3_mm_region_destroy() and ps3_mm_vas_destroy() and replace any error reporting with calls to lv1_panic.
With this change builds with 'DEBUG' defined will not cause kexec reboots to hang, and builds with 'DEBUG' defined or not will end in lv1_panic if an error is encountered.
--- arch/powerpc/platforms/ps3/mm.c | 22 ++++++++++++---------- 1 file changed, 12 insertions(+), 10 deletions(-)
arch/powerpc/platforms/ps3/mm.c +12 -10
@@ -212,13 +212,14 @@ void ps3_mm_vas_destroy(void) {int result; -DBG ("%s:%d: map.vas_id = %llu\n" , __func__, __LINE__, map.vas_id); -if (map.vas_id) { result =lv1_select_virtual_address_space (0 ); -BUG_ON (result); - result =lv1_destruct_virtual_address_space (map.vas_id); -BUG_ON (result); + result +=lv1_destruct_virtual_address_space (map.vas_id); + +if (result) { +lv1_panic (0 ); + } + map.vas_id =0 ; } }
@@ -316,19 +317,20 @@ static void ps3_mm_region_destroy(struct mem_region *r)int result;if (!r->destroy) { -pr_info ("%s:%d: Not destroying high region: %llxh %llxh\n" , - __func__, __LINE__, r->base, r->size);return ; } -DBG ("%s:%d: r->base = %llxh\n" , __func__, __LINE__, r->base); -if (r->base) { result =lv1_release_memory (r->base); -BUG_ON (result); + +if (result) { +lv1_panic (0 ); + } + r->size = r->base = r->offset =0 ; map.total = map.rm.size; } +ps3_mm_set_repository_highmem (NULL ); }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 95/172 vfio-pci: Mask cap zero
In reply to Sasha LevinFrom: Alex Williamson <[email protected]>
[ Upstream commit bc138db1b96264b9c1779cf18d5a3b186aa90066 ]
The PCI Code and ID Assignment Specification changed capability ID 0 from reserved to a NULL capability in the v1.1 revision. The NULL capability is defined to include only the 16-bit capability header, ie. only the ID and next pointer. Unfortunately vfio-pci creates a map of config space, where ID 0 is used to reserve the standard type 0 header. Finding an actual capability with this ID therefore results in a bogus range marked in that map and conflicts with subsequent capabilities. As this seems to be a dummy capability anyway and we already support dropping capabilities, let's hide this one rather than delving into the potentially subtle dependencies within our map.
Seen on an NVIDIA Tesla T4.
--- drivers/vfio/pci/vfio_pci_config.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)
drivers/vfio/pci/vfio_pci_config.c +6 -1
@@ -1464,7 +1464,12 @@ static int vfio_cap_init(struct vfio_pci_device *vdev)if (ret)return ret; -if (cap <=PCI_CAP_ID_MAX ) { +/* +* ID 0 is a NULL capability, conflicting with our fake +* PCI_CAP_ID_BASIC. As it has no content, consider it +* hidden for now. +*/ +if (cap && cap <=PCI_CAP_ID_MAX ) { len = pci_cap_length[cap];if (len ==0xFF ) {/* Variable length */ len =vfio_cap_len (vdev, cap, pos);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 96/172 usb/ohci-platform: Fix a warning when hibernating
In reply to Sasha LevinFrom: Qais Yousef <[email protected]>
[ Upstream commit 1cb3b0095c3d0bb96912bfbbce4fc006d41f367c ]
The following warning was observed when attempting to suspend to disk using a USB flash as a swap device.
[ 111.779649] ------------[ cut here ]------------ [ 111.788382] URB (____ptrval____) submitted while active [ 111.796646] WARNING: CPU: 3 PID: 365 at drivers/usb/core/urb.c:363 usb_submit_urb+0x3d8/0x590 [ 111.805417] Modules linked in: [ 111.808584] CPU: 3 PID: 365 Comm: kworker/3:2 Not tainted 5.6.0-rc6-00002-gdfd1731f9a3e-dirty #545 [ 111.817796] Hardware name: ARM Juno development board (r2) (DT) [ 111.823896] Workqueue: usb_hub_wq hub_event [ 111.828217] pstate: 60000005 (nZCv daif -PAN -UAO) [ 111.833156] pc : usb_submit_urb+0x3d8/0x590 [ 111.837471] lr : usb_submit_urb+0x3d8/0x590 [ 111.841783] sp : ffff800018de38b0 [ 111.845205] x29: ffff800018de38b0 x28: 0000000000000003 [ 111.850682] x27: ffff000970530b20 x26: ffff8000133fd000 [ 111.856159] x25: ffff8000133fd000 x24: ffff800018de3b38 [ 111.861635] x23: 0000000000000004 x22: 0000000000000c00 [ 111.867112] x21: 0000000000000000 x20: 00000000fffffff0 [ 111.872589] x19: ffff0009704e7a00 x18: ffffffffffffffff [ 111.878065] x17: 00000000a7c8f4bc x16: 000000002af33de8 [ 111.883542] x15: ffff8000133fda88 x14: 0720072007200720 [ 111.889019] x13: 0720072007200720 x12: 0720072007200720 [ 111.894496] x11: 0000000000000000 x10: 00000000a5286134 [ 111.899973] x9 : 0000000000000002 x8 : ffff000970c837a0 [ 111.905449] x7 : 0000000000000000 x6 : ffff800018de3570 [ 111.910926] x5 : 0000000000000001 x4 : 0000000000000003 [ 111.916401] x3 : 0000000000000000 x2 : ffff800013427118 [ 111.921879] x1 : 9d4e965b4b7d7c00 x0 : 0000000000000000 [ 111.927356] Call trace: [ 111.929892] usb_submit_urb+0x3d8/0x590 [ 111.933852] hub_activate+0x108/0x7f0 [ 111.937633] hub_resume+0xac/0x148 [ 111.941149] usb_resume_interface.isra.10+0x60/0x138 [ 111.946265] usb_resume_both+0xe4/0x140 [ 111.950225] usb_runtime_resume+0x24/0x30 [ 111.954365] __rpm_callback+0xdc/0x138 [ 111.958236] rpm_callback+0x34/0x98 [ 111.961841] rpm_resume+0x4a8/0x720 [ 111.965445] rpm_resume+0x50c/0x720 [ 111.969049] __pm_runtime_resume+0x4c/0xb8 [ 111.973276] usb_autopm_get_interface+0x28/0x60 [ 111.977948] hub_event+0x80/0x16d8 [ 111.981466] process_one_work+0x2a4/0x748 [ 111.985604] worker_thread+0x48/0x498 [ 111.989387] kthread+0x13c/0x140 [ 111.992725] ret_from_fork+0x10/0x18 [ 111.996415] irq event stamp: 354 [ 111.999756] hardirqs last enabled at (353): [<ffff80001019ea1c>] console_unlock+0x504/0x5b8 [ 112.008441] hardirqs last disabled at (354): [<ffff8000100a95d0>] do_debug_exception+0x1a8/0x258 [ 112.017479] softirqs last enabled at (350): [<ffff8000100818a4>] __do_softirq+0x4bc/0x568 [ 112.025984] softirqs last disabled at (343): [<ffff8000101145a4>] irq_exit+0x144/0x150 [ 112.034129] ---[ end trace dc96030b9cf6c8a3 ]---
The problem was tracked down to a missing call to pm_runtime_set_active() on resume in ohci-platform.
--- drivers/usb/host/ohci-platform.c | 5 +++++ 1 file changed, 5 insertions(+)
drivers/usb/host/ohci-platform.c +5 -0
@@ -301,6 +301,11 @@ static int ohci_platform_resume(struct device *dev) }ohci_resume (hcd, false); + +pm_runtime_disable (dev); +pm_runtime_set_active (dev); +pm_runtime_enable (dev); +return 0 ; }#endif /* CONFIG_PM_SLEEP */
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Sasha Levin
maintainerPATCH 97/172 drm/msm/mdp5: Fix mdp5_init error path for failed mdp5_kms allocation
In reply to Sasha LevinFrom: Roy Spliet <[email protected]>
[ Upstream commit e4337877c5d578722c0716f131fb774522013cf5 ]
When allocation for mdp5_kms fails, calling mdp5_destroy() leads to undefined behaviour, likely a nullptr exception or use-after-free troubles.
--- drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c +2 -1
@@ -1021,7 +1021,8 @@ static int mdp5_init(struct platform_device *pdev, struct drm_device *dev)return 0 ; fail: -mdp5_destroy (pdev); +if (mdp5_kms) +mdp5_destroy (pdev);return ret; }
Signature · 6 lines
2.25.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sasha Levin
maintainerPATCH 98/172 ASoC: Intel: bytcr_rt5640: Add quirk for Toshiba Encore WT8-A tablet
In reply to Sasha LevinFrom: Hans de Goede <[email protected]>
[ Upstream commit 0e0e10fde0e9808d1991268f5dca69fb36c025f7 ]
The Toshiba Encore WT8-A tablet almost fully works with the default settings for non-CR Bay Trail devices. The only problem is that its jack-detect switch is not inverted (it is active high instead of the normal active low).
Add a quirk for this model using the default settings + BYT_RT5640_JD_NOT_INV.
--- sound/soc/intel/boards/bytcr_rt5640.c | 12 ++++++++++++ 1 file changed, 12 insertions(+)
sound/soc/intel/boards/bytcr_rt5640.c +12 -0
@@ -712,6 +712,18 @@ static const struct dmi_system_id byt_rt5640_quirk_table[] = {BYT_RT5640_SSP0_AIF1 | BYT_RT5640_MCLK_EN), }, + { /* Toshiba Encore WT8-A */ + .matches = { +DMI_EXACT_MATCH (DMI_SYS_VENDOR ,"TOSHIBA" ), + DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "TOSHIBA WT8-A"), + }, + .driver_data = (void *)(BYT_RT5640_DMIC1_MAP | +BYT_RT5640_JD_SRC_JD2_IN4N | +BYT_RT5640_OVCD_TH_2000UA | +BYT_RT5640_OVCD_SF_0P75 | +BYT_RT5640_JD_NOT_INV | + BYT_RT5640_MCLK_EN), + }, { /* Catch-all for generic Insyde tablets, must be last */ .matches = { DMI_MATCH(DMI_SYS_VENDOR, "Insyde"),
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 99/172 USB: host: ehci-mxc: Add error handling in ehci_mxc_drv_probe()
In reply to Sasha LevinFrom: Tang Bin <[email protected]>
[ Upstream commit d49292025f79693d3348f8e2029a8b4703be0f0a ]
The function ehci_mxc_drv_probe() does not perform sufficient error checking after executing platform_get_irq(), thus fix it.
--- drivers/usb/host/ehci-mxc.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/usb/host/ehci-mxc.c +2 -0
@@ -50,6 +50,8 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev) } irq =platform_get_irq (pdev,0 ); +if (irq <0 ) +return irq; hcd =usb_create_hcd (&ehci_mxc_hc_driver, dev,dev_name (dev));if (!hcd)
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 100/172 tty: n_gsm: Fix bogus i++ in gsm_data_kick
In reply to Sasha LevinFrom: Gregory CLEMENT <[email protected]>
[ Upstream commit 4dd31f1ffec6c370c3c2e0c605628bf5e16d5c46 ]
When submitting the previous fix "tty: n_gsm: Fix waking up upper tty layer when room available". It was suggested to switch from a while to a for loop, but when doing it, there was a remaining bogus i++.
This patch removes this i++ and also reorganizes the code making it more compact.
--- drivers/tty/n_gsm.c | 14 +++----------- 1 file changed, 3 insertions(+), 11 deletions(-)
drivers/tty/n_gsm.c +3 -11
@@ -703,17 +703,9 @@ static void gsm_data_kick(struct gsm_mux *gsm, struct gsm_dlci *dlci) }else {int i =0 ; -for (i =0 ; i <NUM_DLCI ; i++) { -struct gsm_dlci *dlci; - - dlci = gsm->dlci[i]; -if (dlci ==NULL ) { - i++; -continue ; - } - -tty_port_tty_wakeup (&dlci->port); - } +for (i =0 ; i <NUM_DLCI ; i++) +if (gsm->dlci[i]) +tty_port_tty_wakeup (&gsm->dlci[i]->port); } } }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 101/172 fpga: dfl: afu: Corrected error handling levels
In reply to Sasha LevinFrom: Souptick Joarder <[email protected]>
[ Upstream commit c9d7e3da1f3c4cf5dddfc5d7ce4d76d013aba1cc ]
Corrected error handling goto sequnece. Level put_pages should be called when pinned pages >= 0 && pinned != npages. Level free_pages should be called when pinned pages < 0.
--- drivers/fpga/dfl-afu-dma-region.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/fpga/dfl-afu-dma-region.c +2 -2
@@ -106,10 +106,10 @@ static int afu_dma_pin_pages(struct dfl_feature_platform_data *pdata, region->pages);if (pinned <0 ) { ret = pinned; - goto put_pages; + goto free_pages; }else if (pinned != npages) { ret = -EFAULT ; - goto free_pages; + goto put_pages; }dev_dbg (dev,"%d pages pinned\n" , pinned);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 102/172 clk: samsung: exynos5433: Add IGNORE_UNUSED flag to sclk_i2s1
In reply to Sasha LevinFrom: Marek Szyprowski <[email protected]>
[ Upstream commit 25bdae0f1c6609ceaf55fe6700654f0be2253d8e ]
Mark the SCLK clock for Exynos5433 I2S1 device with IGNORE_UNUSED flag to match its behaviour with SCLK clock for AUD_I2S (I2S0) device until a proper fix for Exynos I2S driver is ready.
This fixes the following synchronous abort issue revealed by the probe order change caused by the commit 93d2e4322aa7 ("of: platform: Batch fwnode parsing when adding all top level devices")
Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP Modules linked in: CPU: 0 PID: 50 Comm: kworker/0:1 Not tainted 5.7.0-rc5+ #701 Hardware name: Samsung TM2E board (DT) Workqueue: events deferred_probe_work_func pstate: 60000005 (nZCv daif -PAN -UAO) pc : samsung_i2s_probe+0x768/0x8f0 lr : samsung_i2s_probe+0x688/0x8f0 ... Call trace: samsung_i2s_probe+0x768/0x8f0 platform_drv_probe+0x50/0xa8 really_probe+0x108/0x370 driver_probe_device+0x54/0xb8 __device_attach_driver+0x90/0xc0 bus_for_each_drv+0x70/0xc8 __device_attach+0xdc/0x140 device_initial_probe+0x10/0x18 bus_probe_device+0x94/0xa0 deferred_probe_work_func+0x70/0xa8 process_one_work+0x2a8/0x718 worker_thread+0x48/0x470 kthread+0x134/0x160 ret_from_fork+0x10/0x1c Code: 17ffffaf d503201f f94086c0 91003000 (88dffc00) ---[ end trace ccf721c9400ddbd6 ]---
--- drivers/clk/samsung/clk-exynos5433.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/clk/samsung/clk-exynos5433.c +2 -1
@@ -1680,7 +1680,8 @@ static const struct samsung_gate_clock peric_gate_clks[] __initconst = {GATE (CLK_SCLK_PCM1 ,"sclk_pcm1" ,"sclk_pcm1_peric" ,ENABLE_SCLK_PERIC ,7 ,CLK_SET_RATE_PARENT ,0 ),GATE (CLK_SCLK_I2S1 ,"sclk_i2s1" ,"sclk_i2s1_peric" , -ENABLE_SCLK_PERIC ,6 ,CLK_SET_RATE_PARENT ,0 ), +ENABLE_SCLK_PERIC ,6 , +CLK_SET_RATE_PARENT |CLK_IGNORE_UNUSED ,0 ),GATE (CLK_SCLK_SPI2 ,"sclk_spi2" ,"sclk_spi2_peric" ,ENABLE_SCLK_PERIC ,5 ,CLK_SET_RATE_PARENT ,0 ), GATE(CLK_SCLK_SPI1, "sclk_spi1", "sclk_spi1_peric", ENABLE_SCLK_PERIC,
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Sasha Levin
maintainerPATCH 103/172 ARM: dts: meson: Switch existing boards with RGMII PHY to "rgmii-id"
In reply to Sasha LevinFrom: Martin Blumenstingl <[email protected]>
[ Upstream commit 005231128e9e97461e81fa32421957a7664317ca ]
Let the PHY generate the RX and TX delay on the Odroid-C1 and MXIII Plus.
Previously we did not know that these boards used an RX delay. We assumed that setting the TX delay on the MAC side It turns out that these boards also require an RX delay of 2ns (verified on Odroid-C1, but the u-boot code uses the same setup on both boards). Ethernet only worked because u-boot added this RX delay on the MAC side.
The 4ns TX delay was also wrong and the result of using an unsupported RGMII TX clock divider setting. This has been fixed in the driver with commit bd6f48546b9cb7 ("net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs").
Switch to phy-mode "rgmii-id" to let the PHY side handle all the delays, (as recommended by the Ethernet maintainers anyways) to correctly describe the need for a 2ns RX as well as 2ns TX delay on these boards. This fixes the Ethernet performance on Odroid-C1 where there was a huge amount of packet loss when transmitting data due to the incorrect TX delay.
--- arch/arm/boot/dts/meson8b-odroidc1.dts | 3 +-- arch/arm/boot/dts/meson8m2-mxiii-plus.dts | 4 +--- 2 files changed, 2 insertions(+), 5 deletions(-)
arch/arm/boot/dts/meson8b-odroidc1.dts +1 -2
@@ -113,9 +113,8 @@ ðmac { pinctrl-0 = <ð_rgmii_pins>; pinctrl-names = "default"; - phy-mode = "rgmii"; phy-handle = <ð_phy>; - amlogic,tx-delay-ns = <4>; + phy-mode = "rgmii-id"; mdio { compatible = "snps,dwmac-mdio";
arch/arm/boot/dts/meson8m2-mxiii-plus.dts +1 -3
@@ -63,9 +63,7 @@ ðmac { pinctrl-names = "default"; phy-handle = <ð_phy0>; - phy-mode = "rgmii"; - - amlogic,tx-delay-ns = <4>; + phy-mode = "rgmii-id"; snps,reset-gpio = <&gpio GPIOH_4 0>; snps,reset-delays-us = <0 10000 1000000>;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 104/172 scsi: target: tcmu: Userspace must not complete queued commands
In reply to Sasha LevinFrom: Bodo Stroesser <[email protected]>
[ Upstream commit 61fb2482216679b9e1e797440c148bb143a5040a ]
When tcmu queues a new command - no matter whether in command ring or in qfull_queue - a cmd_id from IDR udev->commands is assigned to the command.
If userspace sends a wrong command completion containing the cmd_id of a command on the qfull_queue, tcmu_handle_completions() finds the command in the IDR and calls tcmu_handle_completion() for it. This might do some nasty things because commands in qfull_queue do not have a valid dbi list.
To fix this bug, we no longer add queued commands to the idr. Instead the cmd_id is assign when a command is written to the command ring.
Due to this change I had to adapt the source code at several places where up to now an idr_for_each had been done.
[mkp: fix checkpatch warnings]
--- drivers/target/target_core_user.c | 154 ++++++++++++++---------------- 1 file changed, 71 insertions(+), 83 deletions(-)
drivers/target/target_core_user.c +71 -83
@@ -893,41 +893,24 @@ static inline size_t tcmu_cmd_get_cmd_size(struct tcmu_cmd *tcmu_cmd,return command_size; } -static int tcmu_setup_cmd_timer (struct tcmu_cmd *tcmu_cmd,unsigned int tmo, -struct timer_list *timer) +static void tcmu_setup_cmd_timer (struct tcmu_cmd *tcmu_cmd,unsigned int tmo, +struct timer_list *timer) { -struct tcmu_dev *udev = tcmu_cmd->tcmu_dev; -int cmd_id; - -if (tcmu_cmd->cmd_id) - goto setup_timer; - - cmd_id =idr_alloc (&udev->commands, tcmu_cmd,1 ,USHRT_MAX ,GFP_NOWAIT ); -if (cmd_id <0 ) { -pr_err ("tcmu: Could not allocate cmd id.\n" ); -return cmd_id; - } - tcmu_cmd->cmd_id = cmd_id; - -pr_debug ("allocated cmd %u for dev %s tmo %lu\n" , tcmu_cmd->cmd_id, - udev->name, tmo /MSEC_PER_SEC ); - -setup_timer:if (!tmo) -return 0 ; +return ; tcmu_cmd->deadline =round_jiffies_up (jiffies +msecs_to_jiffies (tmo));if (!timer_pending (timer))mod_timer (timer, tcmu_cmd->deadline); -return 0 ; +pr_debug ("Timeout set up for cmd %p, dev = %s, tmo = %lu\n" , tcmu_cmd, + tcmu_cmd->tcmu_dev->name, tmo /MSEC_PER_SEC ); }static int add_to_qfull_queue (struct tcmu_cmd *tcmu_cmd) {struct tcmu_dev *udev = tcmu_cmd->tcmu_dev;unsigned int tmo; -int ret;/* * For backwards compat if qfull_time_out is not set use
@@ -942,13 +925,11 @@ static int add_to_qfull_queue(struct tcmu_cmd *tcmu_cmd)else tmo =TCMU_TIME_OUT ; - ret =tcmu_setup_cmd_timer (tcmu_cmd, tmo, &udev->qfull_timer); -if (ret) -return ret; +tcmu_setup_cmd_timer (tcmu_cmd, tmo, &udev->qfull_timer);list_add_tail (&tcmu_cmd->queue_entry, &udev->qfull_queue); -pr_debug ("adding cmd %u on dev %s to ring space wait queue\n" , - tcmu_cmd->cmd_id, udev->name); +pr_debug ("adding cmd %p on dev %s to ring space wait queue\n" , + tcmu_cmd, udev->name);return 0 ; }
@@ -970,7 +951,7 @@ static int queue_cmd_ring(struct tcmu_cmd *tcmu_cmd, sense_reason_t *scsi_err)struct tcmu_mailbox *mb;struct tcmu_cmd_entry *entry;struct iovec *iov; -int iov_cnt, ret; +int iov_cnt, cmd_id;uint32_t cmd_head;uint64_t cdb_off;bool copy_to_data_area;
@@ -1071,14 +1052,21 @@ static int queue_cmd_ring(struct tcmu_cmd *tcmu_cmd, sense_reason_t *scsi_err) } entry->req.iov_bidi_cnt = iov_cnt; - ret =tcmu_setup_cmd_timer (tcmu_cmd, udev->cmd_time_out, - &udev->cmd_timer); -if (ret) { -tcmu_cmd_free_data (tcmu_cmd, tcmu_cmd->dbi_cnt); + cmd_id =idr_alloc (&udev->commands, tcmu_cmd,1 ,USHRT_MAX ,GFP_NOWAIT ); +if (cmd_id <0 ) { +pr_err ("tcmu: Could not allocate cmd id.\n" ); +tcmu_cmd_free_data (tcmu_cmd, tcmu_cmd->dbi_cnt); *scsi_err =TCM_OUT_OF_RESOURCES ;return -1 ; } + tcmu_cmd->cmd_id = cmd_id; + +pr_debug ("allocated cmd id %u for cmd %p dev %s\n" , tcmu_cmd->cmd_id, + tcmu_cmd, udev->name); + +tcmu_setup_cmd_timer (tcmu_cmd, udev->cmd_time_out, &udev->cmd_timer); + entry->hdr.cmd_id = tcmu_cmd->cmd_id;/*
@@ -1290,50 +1278,39 @@ static unsigned int tcmu_handle_completions(struct tcmu_dev *udev)return handled; } -static int tcmu_check_expired_cmd (int id,void *p,void *data) +static void tcmu_check_expired_ring_cmd (struct tcmu_cmd *cmd) { -struct tcmu_cmd *cmd = p; -struct tcmu_dev *udev = cmd->tcmu_dev; -u8 scsi_status;struct se_cmd *se_cmd; -bool is_running; - -if (test_bit (TCMU_CMD_BIT_EXPIRED , &cmd->flags)) -return 0 ;if (!time_after (jiffies, cmd->deadline)) -return 0 ; +return ; - is_running =test_bit (TCMU_CMD_BIT_INFLIGHT , &cmd->flags); +set_bit (TCMU_CMD_BIT_EXPIRED , &cmd->flags); +list_del_init (&cmd->queue_entry); se_cmd = cmd->se_cmd; + cmd->se_cmd =NULL ; -if (is_running) { -/* -* If cmd_time_out is disabled but qfull is set deadline -* will only reflect the qfull timeout. Ignore it. -*/ -if (!udev->cmd_time_out) -return 0 ; +pr_debug ("Timing out inflight cmd %u on dev %s.\n" , + cmd->cmd_id, cmd->tcmu_dev->name); -set_bit (TCMU_CMD_BIT_EXPIRED , &cmd->flags); -/* -* target_complete_cmd will translate this to LUN COMM FAILURE -*/ - scsi_status =SAM_STAT_CHECK_CONDITION ; -list_del_init (&cmd->queue_entry); - cmd->se_cmd =NULL ; - }else { -list_del_init (&cmd->queue_entry); -idr_remove (&udev->commands, id); -tcmu_free_cmd (cmd); - scsi_status =SAM_STAT_TASK_SET_FULL ; - } +target_complete_cmd (se_cmd,SAM_STAT_CHECK_CONDITION ); +} -pr_debug ("Timing out cmd %u on dev %s that is %s.\n" , - id, udev->name, is_running ?"inflight" :"queued" ); +static void tcmu_check_expired_queue_cmd (struct tcmu_cmd *cmd) +{ +struct se_cmd *se_cmd; -target_complete_cmd (se_cmd, scsi_status); -return 0 ; +if (!time_after (jiffies, cmd->deadline)) +return ; + +list_del_init (&cmd->queue_entry); + se_cmd = cmd->se_cmd; +tcmu_free_cmd (cmd); + +pr_debug ("Timing out queued cmd %p on dev %s.\n" , + cmd, cmd->tcmu_dev->name); + +target_complete_cmd (se_cmd,SAM_STAT_TASK_SET_FULL ); }static void tcmu_device_timedout (struct tcmu_dev *udev)
@@ -1418,16 +1395,15 @@ static struct se_device *tcmu_alloc_device(struct se_hba *hba, const char *name)return &udev->se_dev; } -static bool run_qfull_queue (struct tcmu_dev *udev,bool fail) +static void run_qfull_queue (struct tcmu_dev *udev,bool fail) {struct tcmu_cmd *tcmu_cmd, *tmp_cmd;LIST_HEAD (cmds); -bool drained = true;sense_reason_t scsi_ret;int ret;if (list_empty (&udev->qfull_queue)) -return true; +return ;pr_debug ("running %s's cmdr queue forcefail %d\n" , udev->name, fail);
@@ -1436,11 +1412,10 @@ static bool run_qfull_queue(struct tcmu_dev *udev, bool fail)list_for_each_entry_safe (tcmu_cmd, tmp_cmd, &cmds, queue_entry) {list_del_init (&tcmu_cmd->queue_entry); -pr_debug ("removing cmd %u on dev %s from queue\n" , - tcmu_cmd->cmd_id, udev->name); +pr_debug ("removing cmd %p on dev %s from queue\n" , + tcmu_cmd, udev->name);if (fail) { -idr_remove (&udev->commands, tcmu_cmd->cmd_id);/* * We were not able to even start the command, so * fail with busy to allow a retry in case runner
@@ -1455,10 +1430,8 @@ static bool run_qfull_queue(struct tcmu_dev *udev, bool fail) ret =queue_cmd_ring (tcmu_cmd, &scsi_ret);if (ret <0 ) { -pr_debug ("cmd %u on dev %s failed with %u\n" , - tcmu_cmd->cmd_id, udev->name, scsi_ret); - -idr_remove (&udev->commands, tcmu_cmd->cmd_id); +pr_debug ("cmd %p on dev %s failed with %u\n" , + tcmu_cmd, udev->name, scsi_ret);/* * Ignore scsi_ret for now. target_complete_cmd * drops it.
@@ -1473,13 +1446,11 @@ static bool run_qfull_queue(struct tcmu_dev *udev, bool fail)* the queue */ list_splice_tail (&cmds, &udev->qfull_queue); - drained = false;break ; } }tcmu_set_next_deadline (&udev->qfull_queue, &udev->qfull_timer); -return drained; }static int tcmu_irqcontrol (struct uio_info *info,s32 irq_on)
@@ -1663,6 +1634,8 @@ static void tcmu_dev_kref_release(struct kref *kref)if (tcmu_check_and_free_pending_cmd (cmd) !=0 ) all_expired = false; } +if (!list_empty (&udev->qfull_queue)) + all_expired = false;idr_destroy (&udev->commands);WARN_ON (!all_expired);
@@ -2031,9 +2004,6 @@ static void tcmu_reset_ring(struct tcmu_dev *udev, u8 err_level)mutex_lock (&udev->cmdr_lock);idr_for_each_entry (&udev->commands, cmd, i) { -if (!test_bit (TCMU_CMD_BIT_INFLIGHT , &cmd->flags)) -continue ; -pr_debug ("removing cmd %u on dev %s from ring (is expired %d)\n" , cmd->cmd_id, udev->name,test_bit (TCMU_CMD_BIT_EXPIRED , &cmd->flags));
@@ -2071,6 +2041,8 @@ static void tcmu_reset_ring(struct tcmu_dev *udev, u8 err_level)del_timer (&udev->cmd_timer); +run_qfull_queue (udev, false); +mutex_unlock (&udev->cmdr_lock); }
@@ -2692,6 +2664,7 @@ static void find_free_blocks(void)static void check_timedout_devices (void ) {struct tcmu_dev *udev, *tmp_dev; +struct tcmu_cmd *cmd, *tmp_cmd;LIST_HEAD (devs);spin_lock_bh (&timed_out_udevs_lock);
@@ -2702,9 +2675,24 @@ static void check_timedout_devices(void)spin_unlock_bh (&timed_out_udevs_lock);mutex_lock (&udev->cmdr_lock); -idr_for_each (&udev->commands, tcmu_check_expired_cmd,NULL ); -tcmu_set_next_deadline (&udev->inflight_queue, &udev->cmd_timer); +/* +* If cmd_time_out is disabled but qfull is set deadline +* will only reflect the qfull timeout. Ignore it. +*/ +if (udev->cmd_time_out) { +list_for_each_entry_safe (cmd, tmp_cmd, + &udev->inflight_queue, + queue_entry) { +tcmu_check_expired_ring_cmd (cmd); + } +tcmu_set_next_deadline (&udev->inflight_queue, + &udev->cmd_timer); + } +list_for_each_entry_safe (cmd, tmp_cmd, &udev->qfull_queue, + queue_entry) { +tcmu_check_expired_queue_cmd (cmd); + }tcmu_set_next_deadline (&udev->qfull_queue, &udev->qfull_timer);mutex_unlock (&udev->cmdr_lock);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 105/172 arm64: tegra: Fix ethernet phy-mode for Jetson Xavier
In reply to Sasha LevinFrom: Jon Hunter <[email protected]>
[ Upstream commit bba25915b172c72f6fa635f091624d799e3c9cae ]
The 'phy-mode' property is currently defined as 'rgmii' for Jetson Xavier. This indicates that the RGMII RX and TX delays are set by the MAC and the internal delays set by the PHY are not used.
If the Marvell PHY driver is enabled, such that it is used and not the generic PHY, ethernet failures are seen (DHCP is failing to obtain an IP address) and this is caused because the Marvell PHY driver is disabling the internal RX and TX delays. For Jetson Xavier the internal PHY RX and TX delay should be used and so fix this by setting the 'phy-mode' to 'rgmii-id' and not 'rgmii'.
--- arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi +1 -1
@@ -32,7 +32,7 @@ ethernet@2490000 { phy-reset-gpios = <&gpio TEGRA194_MAIN_GPIO(G, 5) GPIO_ACTIVE_LOW>; phy-handle = <&phy>; - phy-mode = "rgmii"; + phy-mode = "rgmii-id"; mdio { #address-cells = <1>;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 106/172 powerpc/64s/pgtable: fix an undefined behaviour
In reply to Sasha LevinFrom: Qian Cai <[email protected]>
[ Upstream commit c2e929b18cea6cbf71364f22d742d9aad7f4677a ]
Booting a power9 server with hash MMU could trigger an undefined behaviour because pud_offset(p4d, 0) will do,
0 >> (PAGE_SHIFT:16 + PTE_INDEX_SIZE:8 + H_PMD_INDEX_SIZE:10)
Fix it by converting pud_index() and friends to static inline functions.
UBSAN: shift-out-of-bounds in arch/powerpc/mm/ptdump/ptdump.c:282:15 shift exponent 34 is too large for 32-bit type 'int' CPU: 6 PID: 1 Comm: swapper/0 Not tainted 5.6.0-rc4-next-20200303+ #13 Call Trace: dump_stack+0xf4/0x164 (unreliable) ubsan_epilogue+0x18/0x78 __ubsan_handle_shift_out_of_bounds+0x160/0x21c walk_pagetables+0x2cc/0x700 walk_pud at arch/powerpc/mm/ptdump/ptdump.c:282 (inlined by) walk_pagetables at arch/powerpc/mm/ptdump/ptdump.c:311 ptdump_check_wx+0x8c/0xf0 mark_rodata_ro+0x48/0x80 kernel_init+0x74/0x194 ret_from_kernel_thread+0x5c/0x74
--- arch/powerpc/include/asm/book3s/64/pgtable.h | 23 ++++++++++++++++---- 1 file changed, 19 insertions(+), 4 deletions(-)
arch/powerpc/include/asm/book3s/64/pgtable.h +19 -4
@@ -985,10 +985,25 @@ extern struct page *pgd_page(pgd_t pgd);#define pud_page_vaddr (pud) __va(pud_val(pud) & ~PUD_MASKED_BITS)#define pgd_page_vaddr (pgd) __va(pgd_val(pgd) & ~PGD_MASKED_BITS) -#define pgd_index (address) (((address) >> (PGDIR_SHIFT)) & (PTRS_PER_PGD - 1)) -#define pud_index (address) (((address) >> (PUD_SHIFT)) & (PTRS_PER_PUD - 1)) -#define pmd_index (address) (((address) >> (PMD_SHIFT)) & (PTRS_PER_PMD - 1)) -#define pte_index (address) (((address) >> (PAGE_SHIFT)) & (PTRS_PER_PTE - 1)) +static inline unsigned long pgd_index (unsigned long address) +{ +return (address >>PGDIR_SHIFT ) & (PTRS_PER_PGD -1 ); +} + +static inline unsigned long pud_index (unsigned long address) +{ +return (address >>PUD_SHIFT ) & (PTRS_PER_PUD -1 ); +} + +static inline unsigned long pmd_index (unsigned long address) +{ +return (address >>PMD_SHIFT ) & (PTRS_PER_PMD -1 ); +} + +static inline unsigned long pte_index (unsigned long address) +{ +return (address >>PAGE_SHIFT ) & (PTRS_PER_PTE -1 ); +}/* * Find an entry in a page-table-directory. We combine the address region
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 107/172 dm zoned: return NULL if dmz_get_zone_for_reclaim() fails to find a zone
In reply to Sasha LevinFrom: Hannes Reinecke <[email protected]>
[ Upstream commit 489dc0f06a5837f87482c0ce61d830d24e17082e ]
The only case where dmz_get_zone_for_reclaim() cannot return a zone is if the respective lists are empty. So we should just return a simple NULL value here as we really don't have an error code which would make sense.
--- drivers/md/dm-zoned-metadata.c | 4 ++-- drivers/md/dm-zoned-reclaim.c | 4 ++-- 2 files changed, 4 insertions(+), 4 deletions(-)
drivers/md/dm-zoned-metadata.c +2 -2
@@ -1580,7 +1580,7 @@ static struct dm_zone *dmz_get_rnd_zone_for_reclaim(struct dmz_metadata *zmd)return dzone; } -return ERR_PTR (-EBUSY ); +return NULL ; }/*
@@ -1600,7 +1600,7 @@ static struct dm_zone *dmz_get_seq_zone_for_reclaim(struct dmz_metadata *zmd)return zone; } -return ERR_PTR (-EBUSY ); +return NULL ; }/*
drivers/md/dm-zoned-reclaim.c +2 -2
@@ -348,8 +348,8 @@ static int dmz_do_reclaim(struct dmz_reclaim *zrc)/* Get a data zone */ dzone =dmz_get_zone_for_reclaim (zmd); -if (IS_ERR (dzone)) -return PTR_ERR (dzone); +if (!dzone) +return -EBUSY ; start = jiffies;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 108/172 PCI/PTM: Inherit Switch Downstream Port PTM settings from Upstream Port
In reply to Sasha LevinFrom: Bjorn Helgaas <[email protected]>
[ Upstream commit 7b38fd9760f51cc83d80eed2cfbde8b5ead9e93a ]
Except for Endpoints, we enable PTM at enumeration-time. Previously we did not account for the fact that Switch Downstream Ports are not permitted to have a PTM capability; their PTM behavior is controlled by the Upstream Port (PCIe r5.0, sec 7.9.16). Since Downstream Ports don't have a PTM capability, we did not mark them as "ptm_enabled", which meant that pci_enable_ptm() on an Endpoint failed because there was no PTM path to it.
Mark Downstream Ports as "ptm_enabled" if their Upstream Port has PTM enabled.
--- drivers/pci/pcie/ptm.c | 22 +++++++++++++++++----- 1 file changed, 17 insertions(+), 5 deletions(-)
drivers/pci/pcie/ptm.c +17 -5
@@ -39,10 +39,6 @@ void pci_ptm_init(struct pci_dev *dev)if (!pci_is_pcie (dev))return ; - pos =pci_find_ext_capability (dev,PCI_EXT_CAP_ID_PTM ); -if (!pos) -return ; -/* * Enable PTM only on interior devices (root ports, switch ports, * etc.) on the assumption that it causes no link traffic until an
@@ -52,6 +48,23 @@ void pci_ptm_init(struct pci_dev *dev) pci_pcie_type(dev) == PCI_EXP_TYPE_RC_END))return ; +/* +* Switch Downstream Ports are not permitted to have a PTM +* capability; their PTM behavior is controlled by the Upstream +* Port (PCIe r5.0, sec 7.9.16). +*/ + ups =pci_upstream_bridge (dev); +if (pci_pcie_type (dev) ==PCI_EXP_TYPE_DOWNSTREAM && + ups && ups->ptm_enabled) { + dev->ptm_granularity = ups->ptm_granularity; + dev->ptm_enabled =1 ; +return ; + } + + pos =pci_find_ext_capability (dev,PCI_EXT_CAP_ID_PTM ); +if (!pos) +return ; +pci_read_config_dword (dev, pos +PCI_PTM_CAP , &cap); local_clock = (cap &PCI_PTM_GRANULARITY_MASK ) >>8 ;
@@ -61,7 +74,6 @@ void pci_ptm_init(struct pci_dev *dev)* the spec recommendation (PCIe r3.1, sec 7.32.3), select the * furthest upstream Time Source as the PTM Root. */ - ups =pci_upstream_bridge (dev);if (ups && ups->ptm_enabled) { ctrl =PCI_PTM_CTRL_ENABLE ;if (ups->ptm_granularity ==0 )
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 109/172 PCI: dwc: Fix inner MSI IRQ domain registration
In reply to Sasha LevinFrom: Marc Zyngier <[email protected]>
[ Upstream commit 0414b93e78d87ecc24ae1a7e61fe97deb29fa2f4 ]
On a system that uses the internal DWC MSI widget, I get this warning from debugfs when CONFIG_GENERIC_IRQ_DEBUGFS is selected:
debugfs: File ':soc:pcie@fc000000' in directory 'domains' already present!
This is due to the fact that the DWC MSI code tries to register two IRQ domains for the same firmware node, without telling the low level code how to distinguish them (by setting a bus token). This further confuses debugfs which tries to create corresponding files for each domain.
Fix it by tagging the inner domain as DOMAIN_BUS_NEXUS, which is the closest thing we have as to "generic MSI".
--- drivers/pci/controller/dwc/pcie-designware-host.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/pci/controller/dwc/pcie-designware-host.c +2 -0
@@ -285,6 +285,8 @@ int dw_pcie_allocate_domains(struct pcie_port *pp)return -ENOMEM ; } +irq_domain_update_bus_token (pp->irq_domain,DOMAIN_BUS_NEXUS ); + pp->msi_domain =pci_msi_create_irq_domain (fwnode, &dw_pcie_msi_domain_info, pp->irq_domain);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 110/172 IB/cma: Fix ports memory leak in cma_configfs
In reply to Sasha LevinFrom: Maor Gottlieb <[email protected]>
[ Upstream commit 63a3345c2d42a9b29e1ce2d3a4043689b3995cea ]
The allocated ports structure in never freed. The free function should be called by release_cma_ports_group, but the group is never released since we don't remove its default group.
Remove default groups when device group is deleted.
--- drivers/infiniband/core/cma_configfs.c | 13 +++++++++++++ 1 file changed, 13 insertions(+)
drivers/infiniband/core/cma_configfs.c +13 -0
@@ -319,8 +319,21 @@ static struct config_group *make_cma_dev(struct config_group *group,return ERR_PTR (err); } +static void drop_cma_dev (struct config_group *cgroup,struct config_item *item) +{ +struct config_group *group = + container_of(item, struct config_group, cg_item); +struct cma_dev_group *cma_dev_group = + container_of(group, struct cma_dev_group, device_group); + +configfs_remove_default_groups (&cma_dev_group->ports_group); +configfs_remove_default_groups (&cma_dev_group->device_group); +config_item_put (item); +} +static struct configfs_group_operations cma_subsys_group_ops = { .make_group = make_cma_dev, + .drop_item = drop_cma_dev, };static const struct config_item_type cma_subsys_type = {
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 111/172 watchdog: da9062: No need to ping manually before setting timeout
In reply to Sasha LevinFrom: Stefan Riedmueller <[email protected]>
[ Upstream commit a0948ddba65f4f6d3cfb5e2b84685485d0452966 ]
There is actually no need to ping the watchdog before disabling it during timeout change. Disabling the watchdog already takes care of resetting the counter.
This fixes an issue during boot when the userspace watchdog handler takes over and the watchdog is already running. Opening the watchdog in this case leads to the first ping and directly after that without the required heartbeat delay a second ping issued by the set_timeout call. Due to the missing delay this resulted in a reset.
--- drivers/watchdog/da9062_wdt.c | 5 ----- 1 file changed, 5 deletions(-)
drivers/watchdog/da9062_wdt.c +0 -5
@@ -60,11 +60,6 @@ static int da9062_wdt_update_timeout_register(struct da9062_watchdog *wdt, unsigned int regval) {struct da9062 *chip = wdt->hw; -int ret; - - ret =da9062_reset_watchdog_timer (wdt); -if (ret) -return ret; regmap_update_bits(chip->regmap, DA9062AA_CONTROL_D,
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 112/172 usb: dwc2: gadget: move gadget resume after the core is in L0 state
In reply to Sasha LevinFrom: Fabrice Gasnier <[email protected]>
[ Upstream commit 8c935deacebb8fac8f41378701eb79d12f3c2e2d ]
When the remote wakeup interrupt is triggered, lx_state is resumed from L2 to L0 state. But when the gadget resume is called, lx_state is still L2. This prevents the resume callback to queue any request. Any attempt to queue a request from resume callback will result in:
- "submit request only in active state" debug message to be issued
- dwc2_hsotg_ep_queue() returns -EAGAIN
Call the gadget resume routine after the core is in L0 state.
--- drivers/usb/dwc2/core_intr.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/usb/dwc2/core_intr.c +5 -2
@@ -421,10 +421,13 @@ static void dwc2_handle_wakeup_detected_intr(struct dwc2_hsotg *hsotg)if (ret && (ret != -ENOTSUPP ))dev_err (hsotg->dev,"exit power_down failed\n" ); +/* Change to L0 state */ + hsotg->lx_state =DWC2_L0 ;call_gadget (hsotg, resume); + }else { +/* Change to L0 state */ + hsotg->lx_state =DWC2_L0 ; } -/* Change to L0 state */ - hsotg->lx_state =DWC2_L0 ; }else {if (hsotg->params.power_down)return ;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 113/172 USB: gadget: udc: s3c2410_udc: Remove pointless NULL check in s3c2410_udc_nuke
In reply to Sasha LevinFrom: Nathan Chancellor <[email protected]>
[ Upstream commit 7a0fbcf7c308920bc6116b3a5fb21c8cc5fec128 ]
Clang warns:
drivers/usb/gadget/udc/s3c2410_udc.c:255:11: warning: comparison of address of 'ep->queue' equal to a null pointer is always false [-Wtautological-pointer-compare]
if (&ep->queue == NULL)
~~~~^~~~~ ~~~~1 warning generated.
It is not wrong, queue is not a pointer so if ep is not NULL, the address of queue cannot be NULL. No other driver does a check like this and this check has been around since the driver was first introduced, presumably with no issues so it does not seem like this check should be something else. Just remove it.
Commit afe956c577b2d ("kbuild: Enable -Wtautological-compare") exposed this but it is not the root cause of the warning.
--- drivers/usb/gadget/udc/s3c2410_udc.c | 4 ---- 1 file changed, 4 deletions(-)
drivers/usb/gadget/udc/s3c2410_udc.c +0 -4
@@ -264,10 +264,6 @@ static void s3c2410_udc_done(struct s3c2410_ep *ep,static void s3c2410_udc_nuke (struct s3c2410_udc *udc,struct s3c2410_ep *ep,int status) { -/* Sanity check */ -if (&ep->queue ==NULL ) -return ; -while (!list_empty (&ep->queue)) {struct s3c2410_request *req; req = list_entry(ep->queue.next, struct s3c2410_request,
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 114/172 usb: gadget: lpc32xx_udc: don't dereference ep pointer before null check
In reply to Sasha LevinFrom: Colin Ian King <[email protected]>
[ Upstream commit eafa80041645cd7604c4357b1a0cd4a3c81f2227 ]
Currently pointer ep is being dereferenced before it is null checked leading to a null pointer dereference issue. Fix this by only assigning pointer udc once ep is known to be not null. Also remove a debug message that requires a valid udc which may not be possible at that point.
Addresses-Coverity: ("Dereference before null check")
--- drivers/usb/gadget/udc/lpc32xx_udc.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-)
drivers/usb/gadget/udc/lpc32xx_udc.c +6 -5
@@ -1602,17 +1602,17 @@ static int lpc32xx_ep_enable(struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc) { struct lpc32xx_ep *ep = container_of(_ep, struct lpc32xx_ep, ep); -struct lpc32xx_udc *udc = ep->udc; +struct lpc32xx_udc *udc;u16 maxpacket;u32 tmp;unsigned long flags;/* Verify EP data */ if ((!_ep) || (!ep) || (!desc) || - (desc->bDescriptorType !=USB_DT_ENDPOINT )) { -dev_dbg (udc->dev,"bad ep or descriptor\n" ); + (desc->bDescriptorType !=USB_DT_ENDPOINT ))return -EINVAL ; - } + + udc = ep->udc; maxpacket =usb_endpoint_maxp (desc);if ((maxpacket ==0 ) || (maxpacket > ep->maxpacket)) {dev_dbg (udc->dev,"bad ep descriptor's packet size\n" );
@@ -1860,7 +1860,7 @@ static int lpc32xx_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req)static int lpc32xx_ep_set_halt (struct usb_ep *_ep,int value) { struct lpc32xx_ep *ep = container_of(_ep, struct lpc32xx_ep, ep); -struct lpc32xx_udc *udc = ep->udc; +struct lpc32xx_udc *udc;unsigned long flags;if ((!ep) || (ep->hwep_num <=1 ))
@@ -1870,6 +1870,7 @@ static int lpc32xx_ep_set_halt(struct usb_ep *_ep, int value)if (ep->is_in)return -EAGAIN ; + udc = ep->udc;spin_lock_irqsave (&udc->lock, flags);if (value ==1 ) {
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 115/172 usb: gadget: fix potential double-free in m66592_probe.
In reply to Sasha LevinFrom: Qiushi Wu <[email protected]>
[ Upstream commit 44734a594196bf1d474212f38fe3a0d37a73278b ]
m66592_free_request() is called under label "err_add_udc" and "clean_up", and m66592->ep0_req is not set to NULL after first free, leading to a double-free. Fix this issue by setting m66592->ep0_req to NULL after the first free.
--- drivers/usb/gadget/udc/m66592-udc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/usb/gadget/udc/m66592-udc.c +1 -1
@@ -1667,7 +1667,7 @@ static int m66592_probe(struct platform_device *pdev) err_add_udc:m66592_free_request (&m66592->ep[0 ].ep, m66592->ep0_req); - + m66592->ep0_req =NULL ; clean_up3:if (m66592->pdata->on_chip) {clk_disable (m66592->clk);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 116/172 usb: gadget: Fix issue with config_ep_by_speed function
In reply to Sasha LevinFrom: Pawel Laszczak <[email protected]>
[ Upstream commit 5d363120aa548ba52d58907a295eee25f8207ed2 ]
This patch adds new config_ep_by_speed_and_alt function which extends the config_ep_by_speed about alt parameter.
This additional parameter allows to find proper usb_ss_ep_comp_descriptor.
Problem has appeared during testing f_tcm (BOT/UAS) driver function.
f_tcm function for SS use array of headers for both BOT/UAS alternate setting:
static struct usb_descriptor_header *uasp_ss_function_desc[] = {
(struct usb_descriptor_header *) &bot_intf_desc, (struct usb_descriptor_header *) &uasp_ss_bi_desc, (struct usb_descriptor_header *) &bot_bi_ep_comp_desc, (struct usb_descriptor_header *) &uasp_ss_bo_desc, (struct usb_descriptor_header *) &bot_bo_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_intf_desc, (struct usb_descriptor_header *) &uasp_ss_bi_desc, (struct usb_descriptor_header *) &uasp_bi_ep_comp_desc, (struct usb_descriptor_header *) &uasp_bi_pipe_desc, (struct usb_descriptor_header *) &uasp_ss_bo_desc, (struct usb_descriptor_header *) &uasp_bo_ep_comp_desc, (struct usb_descriptor_header *) &uasp_bo_pipe_desc, (struct usb_descriptor_header *) &uasp_ss_status_desc, (struct usb_descriptor_header *) &uasp_status_in_ep_comp_desc, (struct usb_descriptor_header *) &uasp_status_pipe_desc, (struct usb_descriptor_header *) &uasp_ss_cmd_desc, (struct usb_descriptor_header *) &uasp_cmd_comp_desc, (struct usb_descriptor_header *) &uasp_cmd_pipe_desc, NULL,
};
The first 5 descriptors are associated with BOT alternate setting, and others are associated with UAS.
During handling UAS alternate setting f_tcm driver invokes config_ep_by_speed and this function sets incorrect companion endpoint descriptor in usb_ep object.
Instead setting ep->comp_desc to uasp_bi_ep_comp_desc function in this case set ep->comp_desc to uasp_ss_bi_desc.
This is due to the fact that it searches endpoint based on endpoint address:
for_each_ep_desc(speed_desc, d_spd) {
chosen_desc = (struct usb_endpoint_descriptor *)*d_spd;
if (chosen_desc->bEndpoitAddress == _ep->address)
goto ep_found;
}And in result it uses the descriptor from BOT alternate setting instead UAS.
Finally, it causes that controller driver during enabling endpoints detect that just enabled endpoint for bot.
--- drivers/usb/gadget/composite.c | 78 ++++++++++++++++++++++++++-------- include/linux/usb/composite.h | 3 ++ 2 files changed, 64 insertions(+), 17 deletions(-)
drivers/usb/gadget/composite.c +61 -17
@@ -96,40 +96,43 @@ function_descriptors(struct usb_function *f, }/** -* next_ep_desc() - advance to the next EP descriptor +* next_desc() - advance to the next desc_type descriptor * @t: currect pointer within descriptor array +* @desc_type: descriptor type * -* Return: next EP descriptor or NULL +* Return: next desc_type descriptor or NULL * -* Iterate over @t until either EP descriptor found or +* Iterate over @t until either desc_type descriptor found or * NULL (that indicates end of list) encountered */ static struct usb_descriptor_header ** -next_ep_desc (struct usb_descriptor_header **t) +next_desc (struct usb_descriptor_header **t,u8 desc_type) {for (; *t; t++) { -if ((*t)->bDescriptorType ==USB_DT_ENDPOINT ) +if ((*t)->bDescriptorType == desc_type)return t; }return NULL ; }/* -* for_each_ep_desc()- iterate over endpoint descriptors in the -* descriptors list -* @start: pointer within descriptor array. -* @ep_desc: endpoint descriptor to use as the loop cursor +* for_each_desc() - iterate over desc_type descriptors in the +* descriptors list +* @start: pointer within descriptor array. +* @iter_desc: desc_type descriptor to use as the loop cursor +* @desc_type: wanted descriptr type */ -#define for_each_ep_desc (start, ep_desc) \ - for (ep_desc = next_ep_desc(start); \ - ep_desc; ep_desc = next_ep_desc(ep_desc+1)) +#define for_each_desc (start, iter_desc, desc_type) \ + for (iter_desc = next_desc(start, desc_type); \ + iter_desc; iter_desc = next_desc(iter_desc + 1, desc_type))/** -* config_ep_by_speed() - configures the given endpoint +* config_ep_by_speed_and_alt() - configures the given endpoint * according to gadget speed. * @g: pointer to the gadget * @f: usb function * @_ep: the endpoint to configure +* @alt: alternate setting number * * Return: error code, 0 on success *
@@ -142,11 +145,13 @@ next_ep_desc(struct usb_descriptor_header **t)* Note: the supplied function should hold all the descriptors * for supported speeds */ -int config_ep_by_speed (struct usb_gadget *g, -struct usb_function *f, -struct usb_ep *_ep) +int config_ep_by_speed_and_alt (struct usb_gadget *g, +struct usb_function *f, +struct usb_ep *_ep, +u8 alt) {struct usb_endpoint_descriptor *chosen_desc =NULL ; +struct usb_interface_descriptor *int_desc =NULL ;struct usb_descriptor_header **speed_desc =NULL ;struct usb_ss_ep_comp_descriptor *comp_desc =NULL ;
@@ -182,8 +187,21 @@ int config_ep_by_speed(struct usb_gadget *g,default : speed_desc = f->fs_descriptors; } + +/* find correct alternate setting descriptor */ +for_each_desc (speed_desc, d_spd,USB_DT_INTERFACE ) { + int_desc = (struct usb_interface_descriptor *)*d_spd; + +if (int_desc->bAlternateSetting == alt) { + speed_desc = d_spd; + goto intf_found; + } + } +return -EIO ; + +intf_found:/* find descriptors */ -for_each_ep_desc (speed_desc, d_spd) { +for_each_desc (speed_desc, d_spd,USB_DT_ENDPOINT ) { chosen_desc = (struct usb_endpoint_descriptor *)*d_spd;if (chosen_desc->bEndpointAddress == _ep->address) goto ep_found;
@@ -237,6 +255,32 @@ int config_ep_by_speed(struct usb_gadget *g, }return 0 ; } +EXPORT_SYMBOL_GPL (config_ep_by_speed_and_alt); + +/** +* config_ep_by_speed() - configures the given endpoint +* according to gadget speed. +* @g: pointer to the gadget +* @f: usb function +* @_ep: the endpoint to configure +* +* Return: error code, 0 on success +* +* This function chooses the right descriptors for a given +* endpoint according to gadget speed and saves it in the +* endpoint desc field. If the endpoint already has a descriptor +* assigned to it - overwrites it with currently corresponding +* descriptor. The endpoint maxpacket field is updated according +* to the chosen descriptor. +* Note: the supplied function should hold all the descriptors +* for supported speeds +*/ +int config_ep_by_speed (struct usb_gadget *g, +struct usb_function *f, +struct usb_ep *_ep) +{ +return config_ep_by_speed_and_alt (g, f, _ep,0 ); +}EXPORT_SYMBOL_GPL (config_ep_by_speed);/**
include/linux/usb/composite.h +3 -0
@@ -249,6 +249,9 @@ int usb_function_activate(struct usb_function *);int usb_interface_id (struct usb_configuration *,struct usb_function *); +int config_ep_by_speed_and_alt (struct usb_gadget *g,struct usb_function *f, +struct usb_ep *_ep,u8 alt); +int config_ep_by_speed (struct usb_gadget *g,struct usb_function *f,struct usb_ep *_ep);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 117/172 RDMA/iw_cxgb4: cleanup device debugfs entries on ULD remove
In reply to Sasha LevinFrom: Potnuri Bharat Teja <[email protected]>
[ Upstream commit 49ea0c036ede81f126f1a9389d377999fdf5c5a1 ]
Remove device specific debugfs entries immediately if LLD detaches a particular ULD device in case of fatal PCI errors.
--- drivers/infiniband/hw/cxgb4/device.c | 1 + 1 file changed, 1 insertion(+)
drivers/infiniband/hw/cxgb4/device.c +1 -0
@@ -945,6 +945,7 @@ void c4iw_dealloc(struct uld_ctx *ctx)static void c4iw_remove (struct uld_ctx *ctx) {pr_debug ("c4iw_dev %p\n" , ctx->dev); +debugfs_remove_recursive (ctx->dev->debugfs_root);c4iw_unregister_device (ctx->dev);c4iw_dealloc (ctx); }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 118/172 x86/apic: Make TSC deadline timer detection message visible
In reply to Sasha LevinFrom: Borislav Petkov <[email protected]>
[ Upstream commit de308d1815c9e8fe602a958c5c76142ff6501d75 ]
The commit
c84cb3735fd5 ("x86/apic: Move TSC deadline timer debug printk")
removed the message which said that the deadline timer was enabled. It added a pr_debug() message which is issued when deadline timer validation succeeds.
Well, issued only when CONFIG_DYNAMIC_DEBUG is enabled - otherwise pr_debug() calls get optimized away if DEBUG is not defined in the compilation unit.
Therefore, make the above message pr_info() so that it is visible in dmesg.
--- arch/x86/kernel/apic/apic.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/x86/kernel/apic/apic.c +1 -1
@@ -2024,7 +2024,7 @@ void __init init_apic_mappings(void)unsigned int new_apicid;if (apic_validate_deadline_timer ()) -pr_debug ("TSC deadline timer available\n" ); +pr_info ("TSC deadline timer available\n" );if (x2apic_mode) { boot_cpu_physical_apicid =read_apic_id ();
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 119/172 ASoC: fix incomplete error-handling in img_i2s_in_probe.
In reply to Sasha LevinFrom: Qiushi Wu <[email protected]>
[ Upstream commit 25bf943e4e7b47282bd86ae7d39e039217ebb007 ]
Function "pm_runtime_get_sync()" is not handled by "pm_runtime_put()" if "PTR_ERR(rst) == -EPROBE_DEFER". Fix this issue by adding "pm_runtime_put()" into this error path.
--- sound/soc/img/img-i2s-in.c | 1 + 1 file changed, 1 insertion(+)
sound/soc/img/img-i2s-in.c +1 -0
@@ -485,6 +485,7 @@ static int img_i2s_in_probe(struct platform_device *pdev)if (IS_ERR (rst)) {if (PTR_ERR (rst) == -EPROBE_DEFER ) { ret = -EPROBE_DEFER ; +pm_runtime_put (&pdev->dev); goto err_suspend; }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 120/172 vfio/pci: fix memory leaks of eventfd ctx
In reply to Sasha LevinFrom: Qian Cai <[email protected]>
[ Upstream commit 1518ac272e789cae8c555d69951b032a275b7602 ]
Finished a qemu-kvm (-device vfio-pci,host=0001:01:00.0) triggers a few memory leaks after a while because vfio_pci_set_ctx_trigger_single() calls eventfd_ctx_fdget() without the matching eventfd_ctx_put() later. Fix it by calling eventfd_ctx_put() for those memory in vfio_pci_release() before vfio_device_release().
unreferenced object 0xebff008981cc2b00 (size 128):
comm "qemu-kvm", pid 4043, jiffies 4294994816 (age 9796.310s) hex dump (first 32 bytes):
01 00 00 00 6b 6b 6b 6b 00 00 00 00 ad 4e ad de ....kkkk.....N.. ff ff ff ff 6b 6b 6b 6b ff ff ff ff ff ff ff ff ....kkkk........
backtrace:
[<00000000917e8f8d>] slab_post_alloc_hook+0x74/0x9c
[<00000000df0f2aa2>] kmem_cache_alloc_trace+0x2b4/0x3d4
[<000000005fcec025>] do_eventfd+0x54/0x1ac
[<0000000082791a69>] __arm64_sys_eventfd2+0x34/0x44
[<00000000b819758c>] do_el0_svc+0x128/0x1dc
[<00000000b244e810>] el0_sync_handler+0xd0/0x268
[<00000000d495ef94>] el0_sync+0x164/0x180unreferenced object 0x29ff008981cc4180 (size 128):
comm "qemu-kvm", pid 4043, jiffies 4294994818 (age 9796.290s) hex dump (first 32 bytes):
01 00 00 00 6b 6b 6b 6b 00 00 00 00 ad 4e ad de ....kkkk.....N.. ff ff ff ff 6b 6b 6b 6b ff ff ff ff ff ff ff ff ....kkkk........
backtrace:
[<00000000917e8f8d>] slab_post_alloc_hook+0x74/0x9c
[<00000000df0f2aa2>] kmem_cache_alloc_trace+0x2b4/0x3d4
[<000000005fcec025>] do_eventfd+0x54/0x1ac
[<0000000082791a69>] __arm64_sys_eventfd2+0x34/0x44
[<00000000b819758c>] do_el0_svc+0x128/0x1dc
[<00000000b244e810>] el0_sync_handler+0xd0/0x268
[<00000000d495ef94>] el0_sync+0x164/0x180--- drivers/vfio/pci/vfio_pci.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/vfio/pci/vfio_pci.c +4 -0
@@ -407,6 +407,10 @@ static void vfio_pci_release(void *device_data)if (!(--vdev->refcnt)) {vfio_spapr_pci_eeh_release (vdev->pdev);vfio_pci_disable (vdev); +if (vdev->err_trigger) +eventfd_ctx_put (vdev->err_trigger); +if (vdev->req_trigger) +eventfd_ctx_put (vdev->req_trigger); }mutex_unlock (&driver_lock);
Signature · 1 line
2.25.1
Re: [PATCH AUTOSEL 4.19 120/172] vfio/pci: fix memory leaks of eventfd ctx
Quoted 49 lines · On Wed, 17 Jun 2020 21:21:26 -0400 Sasha Levin <[email protected]> wrote:
From: Qian Cai <[email protected]>
[ Upstream commit
1518ac272e789cae8c555d69951b032a275b7602]Finished a qemu-kvm (-device vfio-pci,host=0001:01:00.0) triggers a few memory leaks after a while because
vfio_pci_set_ctx_trigger_single()callseventfd_ctx_fdget()without the matchingeventfd_ctx_put()later. Fix it by callingeventfd_ctx_put()for those memory invfio_pci_release()beforevfio_device_release().unreferenced object
0xebff008981cc2b00(size 128):
comm "qemu-kvm", pid 4043, jiffies 4294994816 (age 9796.310s) hex dump (first 32 bytes):
01 00 00 00 6b 6b 6b 6b 00 00 00 00 ad 4e ad de ....kkkk.....N.. ff ff ff ff 6b 6b 6b 6b ff ff ff ff ff ff ff ff ....kkkk........
backtrace:[<00000000917e8f8d>] slab_post_alloc_hook+0x74/0x9c [<00000000df0f2aa2>] kmem_cache_alloc_trace+0x2b4/0x3d4 [<000000005fcec025>] do_eventfd+0x54/0x1ac [<0000000082791a69>] __arm64_sys_eventfd2+0x34/0x44 [<00000000b819758c>] do_el0_svc+0x128/0x1dc [<00000000b244e810>] el0_sync_handler+0xd0/0x268 [<00000000d495ef94>] el0_sync+0x164/0x180unreferenced object
0x29ff008981cc4180(size 128):
comm "qemu-kvm", pid 4043, jiffies 4294994818 (age 9796.290s) hex dump (first 32 bytes):
01 00 00 00 6b 6b 6b 6b 00 00 00 00 ad 4e ad de ....kkkk.....N.. ff ff ff ff 6b 6b 6b 6b ff ff ff ff ff ff ff ff ....kkkk........
backtrace:[<00000000917e8f8d>] slab_post_alloc_hook+0x74/0x9c [<00000000df0f2aa2>] kmem_cache_alloc_trace+0x2b4/0x3d4 [<000000005fcec025>] do_eventfd+0x54/0x1ac [<0000000082791a69>] __arm64_sys_eventfd2+0x34/0x44 [<00000000b819758c>] do_el0_svc+0x128/0x1dc [<00000000b244e810>] el0_sync_handler+0xd0/0x268 [<00000000d495ef94>] el0_sync+0x164/0x180Signed-off-by Qian Cai <[email protected]>Signed-off-by Alex Williamson <[email protected]>Signed-off-by Sasha Levin <[email protected]>--- drivers/vfio/pci/vfio_pci.c | 4 ++++ 1 file changed, 4 insertions(+)drivers/vfio/pci/vfio_pci.c +0
-0
drivers/vfio/pci/vfio_pci.c static void vfio_pci_release(void *device_data) · line 416
Quoted 10 lines
drivers/vfio/pci/vfio_pci.c +4
-0@@ -407,6 +407,10 @@ static void vfio_pci_release(void *device_data)if (!(--vdev->refcnt)) {vfio_spapr_pci_eeh_release (vdev->pdev);vfio_pci_disable (vdev); +if (vdev->err_trigger) +eventfd_ctx_put (vdev->err_trigger); +if (vdev->req_trigger) +eventfd_ctx_put (vdev->req_trigger); }mutex_unlock (&driver_lock);
This has a fix pending, I'd suggest not picking it on its own:
https://lore.kernel.org/kvm/[email protected]/
https://lore.kernel.org/kvm/[email protected]/
Thanks,
Alex
Sasha Levin
maintainerPATCH 121/172 scsi: target: tcmu: Fix a use after free in tcmu_check_expired_queue_cmd()
In reply to Sasha LevinFrom: Dan Carpenter <[email protected]>
[ Upstream commit 9d7464b18892332e35ff37f0b024429a1a9835e6 ]
The pr_debug() dereferences "cmd" after we already freed it by calling tcmu_free_cmd(cmd). The debug printk needs to be done earlier.
--- drivers/target/target_core_user.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/target/target_core_user.c +3 -3
@@ -1303,13 +1303,13 @@ static void tcmu_check_expired_queue_cmd(struct tcmu_cmd *cmd)if (!time_after (jiffies, cmd->deadline))return ; +pr_debug ("Timing out queued cmd %p on dev %s.\n" , + cmd, cmd->tcmu_dev->name); +list_del_init (&cmd->queue_entry); se_cmd = cmd->se_cmd;tcmu_free_cmd (cmd); -pr_debug ("Timing out queued cmd %p on dev %s.\n" , - cmd, cmd->tcmu_dev->name); -target_complete_cmd (se_cmd,SAM_STAT_TASK_SET_FULL ); }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 122/172 clk: bcm2835: Fix return type of bcm2835_register_gate
In reply to Sasha LevinFrom: Nathan Chancellor <[email protected]>
[ Upstream commit f376c43bec4f8ee8d1ba5c5c4cfbd6e84fb279cb ]
bcm2835_register_gate is used as a callback for the clk_register member of bcm2835_clk_desc, which expects a struct clk_hw * return type but bcm2835_register_gate returns a struct clk *.
This discrepancy is hidden by the fact that bcm2835_register_gate is cast to the typedef bcm2835_clk_register by the _REGISTER macro. This turns out to be a control flow integrity violation, which is how this was noticed.
Change the return type of bcm2835_register_gate to be struct clk_hw * and use clk_hw_register_gate to do so. This should be a non-functional change as clk_register_gate calls clk_hw_register_gate anyways but this is needed to avoid issues with further changes.
--- drivers/clk/bcm/clk-bcm2835.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-)
drivers/clk/bcm/clk-bcm2835.c +5 -5
@@ -1447,13 +1447,13 @@ static struct clk_hw *bcm2835_register_clock(struct bcm2835_cprman *cprman,return &clock->hw; } -static struct clk *bcm2835_register_gate (struct bcm2835_cprman *cprman, +static struct clk_hw *bcm2835_register_gate (struct bcm2835_cprman *cprman,const struct bcm2835_gate_data *data) { -return clk_register_gate (cprman->dev, data->name, data->parent, -CLK_IGNORE_UNUSED |CLK_SET_RATE_GATE , - cprman->regs + data->ctl_reg, -CM_GATE_BIT ,0 , &cprman->regs_lock); +return clk_hw_register_gate (cprman->dev, data->name, data->parent, +CLK_IGNORE_UNUSED |CLK_SET_RATE_GATE , + cprman->regs + data->ctl_reg, +CM_GATE_BIT ,0 , &cprman->regs_lock); } typedef struct clk_hw *(*bcm2835_clk_register)(struct bcm2835_cprman *cprman,
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Sasha Levin
maintainerPATCH 123/172 scsi: ufs-qcom: Fix scheduling while atomic issue
In reply to Sasha LevinFrom: Jeffrey Hugo <[email protected]>
[ Upstream commit 3be60b564de49875e47974c37fabced893cd0931 ]
ufs_qcom_dump_dbg_regs() uses usleep_range, a sleeping function, but can be called from atomic context in the following flow:
ufshcd_intr -> ufshcd_sl_intr -> ufshcd_check_errors -> ufshcd_print_host_regs -> ufshcd_vops_dbg_register_dump -> ufs_qcom_dump_dbg_regs
This causes a boot crash on the Lenovo Miix 630 when the interrupt is handled on the idle thread.
Fix the issue by switching to udelay().
--- drivers/scsi/ufs/ufs-qcom.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/scsi/ufs/ufs-qcom.c +3 -3
@@ -1635,11 +1635,11 @@ static void ufs_qcom_dump_dbg_regs(struct ufs_hba *hba)/* sleep a bit intermittently as we are dumping too much data */ ufs_qcom_print_hw_debug_reg_all (hba,NULL , ufs_qcom_dump_regs_wrapper); -usleep_range (1000 ,1100 ); +udelay (1000 );ufs_qcom_testbus_read (hba); -usleep_range (1000 ,1100 ); +udelay (1000 );ufs_qcom_print_unipro_testbus (hba); -usleep_range (1000 ,1100 ); +udelay (1000 ); }/**
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 124/172 KVM: PPC: Book3S HV: Ignore kmemleak false positives
In reply to Sasha LevinFrom: Qian Cai <[email protected]>
[ Upstream commit 0aca8a5575544bd21b3363058afb8f1e81505150 ]
kvmppc_pmd_alloc() and kvmppc_pte_alloc() allocate some memory but then pud_populate() and pmd_populate() will use __pa() to reference the newly allocated memory.
Since kmemleak is unable to track the physical memory resulting in false positives, silence those by using kmemleak_ignore().
unreferenced object 0xc000201c382a1000 (size 4096):
comm "qemu-kvm", pid 124828, jiffies 4295733767 (age 341.250s) hex dump (first 32 bytes):
c0 00 20 09 f4 60 03 87 c0 00 20 10 72 a0 03 87 .. ..`.... .r... c0 00 20 0e 13 a0 03 87 c0 00 20 1b dc c0 03 87 .. ....... .....
backtrace:
[<000000004cc2790f>] kvmppc_create_pte+0x838/0xd20 [kvm_hv] kvmppc_pmd_alloc at arch/powerpc/kvm/book3s_64_mmu_radix.c:366 (inlined by) kvmppc_create_pte at arch/powerpc/kvm/book3s_64_mmu_radix.c:590 [<00000000d123c49a>] kvmppc_book3s_instantiate_page+0x2e0/0x8c0 [kvm_hv] [<00000000bb549087>] kvmppc_book3s_radix_page_fault+0x1b4/0x2b0 [kvm_hv] [<0000000086dddc0e>] kvmppc_book3s_hv_page_fault+0x214/0x12a0 [kvm_hv] [<000000005ae9ccc2>] kvmppc_vcpu_run_hv+0xc5c/0x15f0 [kvm_hv] [<00000000d22162ff>] kvmppc_vcpu_run+0x34/0x48 [kvm] [<00000000d6953bc4>] kvm_arch_vcpu_ioctl_run+0x314/0x420 [kvm] [<000000002543dd54>] kvm_vcpu_ioctl+0x33c/0x950 [kvm] [<0000000048155cd6>] ksys_ioctl+0xd8/0x130 [<0000000041ffeaa7>] sys_ioctl+0x28/0x40 [<000000004afc4310>] system_call_exception+0x114/0x1e0 [<00000000fb70a873>] system_call_common+0xf0/0x278
unreferenced object 0xc0002001f0c03900 (size 256):
comm "qemu-kvm", pid 124830, jiffies 4295735235 (age 326.570s) hex dump (first 32 bytes):
c0 00 20 10 fa a0 03 87 c0 00 20 10 fa a1 03 87 .. ....... ..... c0 00 20 10 fa a2 03 87 c0 00 20 10 fa a3 03 87 .. ....... .....
backtrace:
[<0000000023f675b8>] kvmppc_create_pte+0x854/0xd20 [kvm_hv] kvmppc_pte_alloc at arch/powerpc/kvm/book3s_64_mmu_radix.c:356 (inlined by) kvmppc_create_pte at arch/powerpc/kvm/book3s_64_mmu_radix.c:593 [<00000000d123c49a>] kvmppc_book3s_instantiate_page+0x2e0/0x8c0 [kvm_hv] [<00000000bb549087>] kvmppc_book3s_radix_page_fault+0x1b4/0x2b0 [kvm_hv] [<0000000086dddc0e>] kvmppc_book3s_hv_page_fault+0x214/0x12a0 [kvm_hv] [<000000005ae9ccc2>] kvmppc_vcpu_run_hv+0xc5c/0x15f0 [kvm_hv] [<00000000d22162ff>] kvmppc_vcpu_run+0x34/0x48 [kvm] [<00000000d6953bc4>] kvm_arch_vcpu_ioctl_run+0x314/0x420 [kvm] [<000000002543dd54>] kvm_vcpu_ioctl+0x33c/0x950 [kvm] [<0000000048155cd6>] ksys_ioctl+0xd8/0x130 [<0000000041ffeaa7>] sys_ioctl+0x28/0x40 [<000000004afc4310>] system_call_exception+0x114/0x1e0 [<00000000fb70a873>] system_call_common+0xf0/0x278
--- arch/powerpc/kvm/book3s_64_mmu_radix.c | 16 ++++++++++++++-- 1 file changed, 14 insertions(+), 2 deletions(-)
arch/powerpc/kvm/book3s_64_mmu_radix.c +14 -2
@@ -171,7 +171,13 @@ static struct kmem_cache *kvm_pmd_cache;static pte_t *kvmppc_pte_alloc (void ) { -return kmem_cache_alloc (kvm_pte_cache,GFP_KERNEL ); +pte_t *pte; + + pte =kmem_cache_alloc (kvm_pte_cache,GFP_KERNEL ); +/* pmd_populate() will only reference _pa(pte). */ +kmemleak_ignore (pte); + +return pte; }static void kvmppc_pte_free (pte_t *ptep)
@@ -187,7 +193,13 @@ static inline int pmd_is_leaf(pmd_t pmd)static pmd_t *kvmppc_pmd_alloc (void ) { -return kmem_cache_alloc (kvm_pmd_cache,GFP_KERNEL ); +pmd_t *pmd; + + pmd =kmem_cache_alloc (kvm_pmd_cache,GFP_KERNEL ); +/* pud_populate() will only reference _pa(pmd). */ +kmemleak_ignore (pmd); + +return pmd; }static void kvmppc_pmd_free (pmd_t *pmdp)
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 125/172 clk: sprd: return correct type of value for _sprd_pll_recalc_rate
In reply to Sasha LevinFrom: Chunyan Zhang <[email protected]>
[ Upstream commit c2f30986d418f26abefc2eec90ebf06716c970d2 ]
The function _sprd_pll_recalc_rate() defines return value to unsigned long, but it would return a negative value when malloc fail, changing to return its parent_rate makes more sense, since if the callback .recalc_rate() is not set, the framework returns the parent_rate as well.
--- drivers/clk/sprd/pll.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/clk/sprd/pll.c +1 -1
@@ -105,7 +105,7 @@ static unsigned long _sprd_pll_recalc_rate(const struct sprd_pll *pll, cfg =kcalloc (regs_num,sizeof (*cfg),GFP_KERNEL );if (!cfg) -return -ENOMEM ; +return parent_rate;for (i =0 ; i < regs_num; i++) cfg[i] =sprd_pll_read (pll, i);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 126/172 net: sunrpc: Fix off-by-one issues in 'rpc_ntop6'
In reply to Sasha LevinFrom: Fedor Tokarev <[email protected]>
[ Upstream commit 118917d696dc59fd3e1741012c2f9db2294bed6f ]
Fix off-by-one issues in 'rpc_ntop6':
- 'snprintf' returns the number of characters which would have been written if enough space had been available, excluding the terminating null byte. Thus, a return value of 'sizeof(scopebuf)' means that the last character was dropped.
- 'strcat' adds a terminating null byte to the string, thus if len == buflen, the null byte is written past the end of the buffer.
--- net/sunrpc/addr.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
net/sunrpc/addr.c +2 -2
@@ -81,11 +81,11 @@ static size_t rpc_ntop6(const struct sockaddr *sap, rc =snprintf (scopebuf,sizeof (scopebuf),"%c%u" ,IPV6_SCOPE_DELIMITER , sin6->sin6_scope_id); -if (unlikely ((size_t )rc >sizeof (scopebuf))) +if (unlikely ((size_t )rc >=sizeof (scopebuf)))return 0 ; len += rc; -if (unlikely (len > buflen)) +if (unlikely (len >= buflen))return 0 ;strcat (buf, scopebuf);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 127/172 NFSv4.1 fix rpc_call_done assignment for BIND_CONN_TO_SESSION
In reply to Sasha LevinFrom: Olga Kornievskaia <[email protected]>
[ Upstream commit 1c709b766e73e54d64b1dde1b7cfbcf25bcb15b9 ]
--- fs/nfs/nfs4proc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
fs/nfs/nfs4proc.c +1 -1
@@ -7624,7 +7624,7 @@ nfs4_bind_one_conn_to_session_done(struct rpc_task *task, void *calldata) }static const struct rpc_call_ops nfs4_bind_one_conn_to_session_ops = { - .rpc_call_done = &nfs4_bind_one_conn_to_session_done, + .rpc_call_done = nfs4_bind_one_conn_to_session_done, };/*
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 128/172 PCI: Avoid FLR for AMD Matisse HD Audio & USB 3.0
In reply to Sasha LevinFrom: Marcos Scriven <[email protected]>
[ Upstream commit 0d14f06cd6657ba3446a5eb780672da487b068e7 ]
The AMD Matisse HD Audio & USB 3.0 devices advertise Function Level Reset support, but hang when an FLR is triggered.
To reproduce the problem, attach the device to a VM, then detach and try to attach again.
Rename the existing quirk_intel_no_flr(), which was not Intel-specific, to quirk_no_flr(), and apply it to prevent the use of FLR on these AMD devices.
--- drivers/pci/quirks.c | 18 ++++++++++++++---- 1 file changed, 14 insertions(+), 4 deletions(-)
drivers/pci/quirks.c +14 -4
@@ -4956,13 +4956,23 @@ static void quirk_intel_qat_vf_cap(struct pci_dev *pdev) }DECLARE_PCI_FIXUP_EARLY (PCI_VENDOR_ID_INTEL ,0x443 , quirk_intel_qat_vf_cap); -/* FLR may cause some 82579 devices to hang */ -static void quirk_intel_no_flr (struct pci_dev *dev) +/* +* FLR may cause the following to devices to hang: +* +* AMD Starship/Matisse HD Audio Controller 0x1487 +* AMD Matisse USB 3.0 Host Controller 0x149c +* Intel 82579LM Gigabit Ethernet Controller 0x1502 +* Intel 82579V Gigabit Ethernet Controller 0x1503 +* +*/ +static void quirk_no_flr (struct pci_dev *dev) { dev->dev_flags |=PCI_DEV_FLAGS_NO_FLR_RESET ; } -DECLARE_PCI_FIXUP_EARLY (PCI_VENDOR_ID_INTEL ,0x1502 , quirk_intel_no_flr); -DECLARE_PCI_FIXUP_EARLY (PCI_VENDOR_ID_INTEL ,0x1503 , quirk_intel_no_flr); +DECLARE_PCI_FIXUP_EARLY (PCI_VENDOR_ID_AMD ,0x1487 , quirk_no_flr); +DECLARE_PCI_FIXUP_EARLY (PCI_VENDOR_ID_AMD ,0x149c , quirk_no_flr); +DECLARE_PCI_FIXUP_EARLY (PCI_VENDOR_ID_INTEL ,0x1502 , quirk_no_flr); +DECLARE_PCI_FIXUP_EARLY (PCI_VENDOR_ID_INTEL ,0x1503 , quirk_no_flr);static void quirk_no_ext_tags (struct pci_dev *pdev) {
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 129/172 PCI: Avoid FLR for AMD Starship USB 3.0
In reply to Sasha LevinFrom: Kevin Buettner <[email protected]>
[ Upstream commit 5727043c73fdfe04597971b5f3f4850d879c1f4f ]
The AMD Starship USB 3.0 host controller advertises Function Level Reset support, but it apparently doesn't work. Add a quirk to prevent use of FLR on this device.
Without this quirk, when attempting to assign (pass through) an AMD Starship USB 3.0 host controller to a guest OS, the system becomes increasingly unresponsive over the course of several minutes, eventually requiring a hard reset. Shortly after attempting to start the guest, I see these messages:
vfio-pci 0000:05:00.3: not ready 1023ms after FLR; waiting vfio-pci 0000:05:00.3: not ready 2047ms after FLR; waiting vfio-pci 0000:05:00.3: not ready 4095ms after FLR; waiting vfio-pci 0000:05:00.3: not ready 8191ms after FLR; waiting
And then eventually:
vfio-pci 0000:05:00.3: not ready 65535ms after FLR; giving up
INFO: NMI handler (perf_event_nmi_handler) took too long to run: 0.000 msecs
perf: interrupt took too long (642744 > 2500), lowering kernel.perf_event_max_sample_rate to 1000
INFO: NMI handler (perf_event_nmi_handler) took too long to run: 82.270 msecs
INFO: NMI handler (perf_event_nmi_handler) took too long to run: 680.608 msecs
INFO: NMI handler (perf_event_nmi_handler) took too long to run: 100.952 msecs
...
watchdog: BUG: soft lockup - CPU#3 stuck for 22s! [qemu-system-x86:7487]
Tested on a Micro-Star International Co., Ltd. MS-7C59/Creator TRX40 motherboard with an AMD Ryzen Threadripper 3970X.
--- drivers/pci/quirks.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/pci/quirks.c +2 -0
@@ -4960,6 +4960,7 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x443, quirk_intel_qat_vf_cap);* FLR may cause the following to devices to hang: * * AMD Starship/Matisse HD Audio Controller 0x1487 +* AMD Starship USB 3.0 Host Controller 0x148c * AMD Matisse USB 3.0 Host Controller 0x149c * Intel 82579LM Gigabit Ethernet Controller 0x1502 * Intel 82579V Gigabit Ethernet Controller 0x1503
@@ -4970,6 +4971,7 @@ static void quirk_no_flr(struct pci_dev *dev) dev->dev_flags |=PCI_DEV_FLAGS_NO_FLR_RESET ; }DECLARE_PCI_FIXUP_EARLY (PCI_VENDOR_ID_AMD ,0x1487 , quirk_no_flr); +DECLARE_PCI_FIXUP_EARLY (PCI_VENDOR_ID_AMD ,0x148c , quirk_no_flr);DECLARE_PCI_FIXUP_EARLY (PCI_VENDOR_ID_AMD ,0x149c , quirk_no_flr);DECLARE_PCI_FIXUP_EARLY (PCI_VENDOR_ID_INTEL ,0x1502 , quirk_no_flr);DECLARE_PCI_FIXUP_EARLY (PCI_VENDOR_ID_INTEL ,0x1503 , quirk_no_flr);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 130/172 of: Fix a refcounting bug in __of_attach_node_sysfs()
In reply to Sasha LevinFrom: Dan Carpenter <[email protected]>
[ Upstream commit 8a325dd06f2358ea0888e4ff1c9ca4bc23bd53f3 ]
The problem in this code is that if kobject_add() fails, then it should call of_node_put(np) to drop the reference count. I've actually moved the of_node_get(np) later in the function to avoid needing to do clean up.
--- drivers/of/kobj.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/of/kobj.c +1 -2
@@ -134,8 +134,6 @@ int __of_attach_node_sysfs(struct device_node *np)if (!name)return -ENOMEM ; -of_node_get (np); - rc =kobject_add (&np->kobj, parent,"%s" , name);kfree (name);if (rc)
@@ -144,6 +142,7 @@ int __of_attach_node_sysfs(struct device_node *np)for_each_property_of_node (np, pp)__of_add_property_sysfs (np, pp); +of_node_get (np);return 0 ; }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 131/172 powerpc/4xx: Don't unmap NULL mbase
In reply to Sasha LevinFrom: huhai <[email protected]>
[ Upstream commit bcec081ecc940fc38730b29c743bbee661164161 ]
--- arch/powerpc/platforms/4xx/pci.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-)
arch/powerpc/platforms/4xx/pci.c +1 -3
@@ -1242,7 +1242,7 @@ static void __init ppc460sx_pciex_check_link(struct ppc4xx_pciex_port *port)if (mbase ==NULL ) {printk (KERN_ERR "%pOF: Can't map internal config space !" , port->node); - goto done; +return ; } while (attempt && (0 == (in_le32(mbase + PECFG_460SX_DLLSTA)
@@ -1252,9 +1252,7 @@ static void __init ppc460sx_pciex_check_link(struct ppc4xx_pciex_port *port) }if (attempt) port->link =1 ; -done:iounmap (mbase); - }static struct ppc4xx_pciex_hwops ppc460sx_pcie_hwops__initdata = {
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 132/172 extcon: adc-jack: Fix an error handling path in 'adc_jack_probe()'
In reply to Sasha LevinFrom: Christophe JAILLET <[email protected]>
[ Upstream commit bc84cff2c92ae5ccb2c37da73756e7174b1b430f ]
In some error handling paths, a call to 'iio_channel_get()' is not balanced by a corresponding call to 'iio_channel_release()'.
This can be achieved easily by using the devm_ variant of 'iio_channel_get()'.
This has the extra benefit to simplify the remove function.
--- drivers/extcon/extcon-adc-jack.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/extcon/extcon-adc-jack.c +1 -2
@@ -128,7 +128,7 @@ static int adc_jack_probe(struct platform_device *pdev)for (i =0 ; data->adc_conditions[i].id !=EXTCON_NONE ; i++); data->num_conditions = i; - data->chan =iio_channel_get (&pdev->dev, pdata->consumer_channel); + data->chan =devm_iio_channel_get (&pdev->dev, pdata->consumer_channel);if (IS_ERR (data->chan))return PTR_ERR (data->chan);
@@ -170,7 +170,6 @@ static int adc_jack_remove(struct platform_device *pdev)free_irq (data->irq, data);cancel_work_sync (&data->handler.work); -iio_channel_release (data->chan);return 0 ; }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 133/172 ASoC: fsl_asrc_dma: Fix dma_chan leak when config DMA channel failed
In reply to Sasha LevinFrom: Xiyu Yang <[email protected]>
[ Upstream commit 36124fb19f1ae68a500cd76a76d40c6e81bee346 ]
fsl_asrc_dma_hw_params() invokes dma_request_channel() or fsl_asrc_get_dma_channel(), which returns a reference of the specified dma_chan object to "pair->dma_chan[dir]" with increased refcnt.
The reference counting issue happens in one exception handling path of fsl_asrc_dma_hw_params(). When config DMA channel failed for Back-End, the function forgets to decrease the refcnt increased by dma_request_channel() or fsl_asrc_get_dma_channel(), causing a refcnt leak.
Fix this issue by calling dma_release_channel() when config DMA channel failed.
--- sound/soc/fsl/fsl_asrc_dma.c | 1 + 1 file changed, 1 insertion(+)
sound/soc/fsl/fsl_asrc_dma.c +1 -0
@@ -241,6 +241,7 @@ static int fsl_asrc_dma_hw_params(struct snd_pcm_substream *substream, ret =dmaengine_slave_config (pair->dma_chan[dir], &config_be);if (ret) {dev_err (dev,"failed to config DMA channel for Back-End\n" ); +dma_release_channel (pair->dma_chan[dir]);return ret; }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 134/172 vfio/mdev: Fix reference count leak in add_mdev_supported_type
In reply to Sasha LevinFrom: Qiushi Wu <[email protected]>
[ Upstream commit aa8ba13cae3134b8ef1c1b6879f66372531da738 ]
kobject_init_and_add() takes reference even when it fails. If this function returns an error, kobject_put() must be called to properly clean up the memory associated with the object. Thus, replace kfree() by kobject_put() to fix this issue. Previous commit "b8eb718348b8" fixed a similar problem.
--- drivers/vfio/mdev/mdev_sysfs.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/vfio/mdev/mdev_sysfs.c +1 -1
@@ -113,7 +113,7 @@ struct mdev_type *add_mdev_supported_type(struct mdev_parent *parent,"%s-%s" ,dev_driver_string (parent->dev), group->name);if (ret) { -kfree (type); +kobject_put (&type->kobj);return ERR_PTR (ret); }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 135/172 rxrpc: Adjust /proc/net/rxrpc/calls to display call->debug_id not user_ID
In reply to Sasha LevinFrom: David Howells <[email protected]>
[ Upstream commit 32f71aa497cfb23d37149c2ef16ad71fce2e45e2 ]
The user ID value isn't actually much use - and leaks a kernel pointer or a userspace value - so replace it with the call debug ID, which appears in trace points.
--- net/rxrpc/proc.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
net/rxrpc/proc.c +3 -3
@@ -72,7 +72,7 @@ static int rxrpc_call_seq_show(struct seq_file *seq, void *v)"Proto Local " " Remote " " SvID ConnID CallID End Use State Abort " - " UserID TxSeq TW RxSeq RW RxSerial RxTimo\n"); + " DebugId TxSeq TW RxSeq RW RxSerial RxTimo\n");return 0 ; }
@@ -104,7 +104,7 @@ static int rxrpc_call_seq_show(struct seq_file *seq, void *v) rx_hard_ack =READ_ONCE (call->rx_hard_ack); seq_printf(seq, "UDP %-47.47s %-47.47s %4x %08x %08x %s %3u" - " %-8.8s %08x %lx %08x %02x %08x %02x %08x %06lx\n", + " %-8.8s %08x %08x %08x %02x %08x %02x %08x %06lx\n", lbuff, rbuff, call->service_id,
@@ -114,7 +114,7 @@ static int rxrpc_call_seq_show(struct seq_file *seq, void *v)atomic_read (&call->usage), rxrpc_call_states[call->state], call->abort_code, - call->user_call_ID, + call->debug_id, tx_hard_ack,READ_ONCE (call->tx_top) - tx_hard_ack, rx_hard_ack,READ_ONCE (call->rx_top) - rx_hard_ack, call->rx_serial,
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 136/172 openrisc: Fix issue with argument clobbering for clone/fork
In reply to Sasha LevinFrom: Stafford Horne <[email protected]>
[ Upstream commit 6bd140e14d9aaa734ec37985b8b20a96c0ece948 ]
Working on the OpenRISC glibc port I found that sometimes clone was working strange. That the tls data argument sent in r7 was always wrong. Further investigation revealed that the arguments were getting clobbered in the entry code. This patch removes the code that writes to the argument registers. This was likely due to some old code hanging around.
This patch fixes this up for clone and fork. This fork clobber is harmless but also useless so remove.
--- arch/openrisc/kernel/entry.S | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/openrisc/kernel/entry.S +2 -2
@@ -1170,13 +1170,13 @@ ENTRY(__sys_clone) l.movhi r29,hi(sys_clone) l.ori r29,r29,lo(sys_clone) l.j _fork_save_extra_regs_and_call - l.addi r7,r1,0 + l.nop ENTRY(__sys_fork) l.movhi r29,hi(sys_fork) l.ori r29,r29,lo(sys_fork) l.j _fork_save_extra_regs_and_call - l.addi r3,r1,0 + l.nop ENTRY(sys_rt_sigreturn) l.jal _sys_rt_sigreturn
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 137/172 gfs2: Allow lock_nolock mount to specify jid=X
In reply to Sasha LevinFrom: Bob Peterson <[email protected]>
[ Upstream commit ea22eee4e6027d8927099de344f7fff43c507ef9 ]
Before this patch, a simple typo accidentally added \n to the jid= string for lock_nolock mounts. This made it impossible to mount a gfs2 file system with a journal other than journal0. Thus:
mount -tgfs2 -o hostdata="jid=1" <device> <mount pt>
Resulted in:
mount: wrong fs type, bad option, bad superblock on <device>
In most cases this is not a problem. However, for debugging and testing purposes we sometimes want to test the integrity of other journals. This patch removes the unnecessary \n and thus allows lock_nolock users to specify an alternate journal.
--- fs/gfs2/ops_fstype.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
fs/gfs2/ops_fstype.c +1 -1
@@ -903,7 +903,7 @@ static int init_per_node(struct gfs2_sbd *sdp, int undo) }static const match_table_t nolock_tokens = { - { Opt_jid,"jid=%d\n" , }, + { Opt_jid,"jid=%d" , }, { Opt_err,NULL }, };
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 138/172 ovl: verify permissions in ovl_path_open()
In reply to Sasha LevinFrom: Miklos Szeredi <[email protected]>
[ Upstream commit 56230d956739b9cb1cbde439d76227d77979a04d ]
Check permission before opening a real file.
ovl_path_open() is used by readdir and copy-up routines.
ovl_permission() theoretically already checked copy up permissions, but it doesn't hurt to re-do these checks during the actual copy-up.
For directory reading ovl_permission() only checks access to topmost underlying layer. Readdir on a merged directory accesses layers below the topmost one as well. Permission wasn't checked for these layers.
Note: modifying ovl_permission() to perform this check would be far more complex and hence more bug prone. The result is less precise permissions returned in access(2). If this turns out to be an issue, we can revisit this bug.
--- fs/overlayfs/util.c | 27 ++++++++++++++++++++++++++- 1 file changed, 26 insertions(+), 1 deletion(-)
fs/overlayfs/util.c +26 -1
@@ -479,7 +479,32 @@ bool ovl_is_whiteout(struct dentry *dentry)struct file *ovl_path_open (struct path *path,int flags) { -return dentry_open (path, flags |O_NOATIME ,current_cred ()); +struct inode *inode =d_inode (path->dentry); +int err, acc_mode; + +if (flags & ~(O_ACCMODE |O_LARGEFILE )) +BUG (); + +switch (flags &O_ACCMODE ) { +case O_RDONLY : + acc_mode =MAY_READ ; +break ; +case O_WRONLY : + acc_mode =MAY_WRITE ; +break ; +default : +BUG (); + } + + err =inode_permission (inode, acc_mode |MAY_OPEN ); +if (err) +return ERR_PTR (err); + +/* O_NOATIME is an optimization, don't fail if not permitted */ +if (inode_owner_or_capable (inode)) + flags |=O_NOATIME ; + +return dentry_open (path, flags,current_cred ()); }/* Caller should hold ovl_inode->lock */
Signature · 1 line
2.25.1
Re: [PATCH AUTOSEL 4.19 138/172] ovl: verify permissions in ovl_path_open()
Quoted 32 lines · Sasha Levin
From: Miklos Szeredi <[email protected]>
[ Upstream commit
56230d956739b9cb1cbde439d76227d77979a04d]Check permission before opening a real file.
ovl_path_open()is used by readdir and copy-up routines.
ovl_permission()theoretically already checked copy up permissions, but it doesn't hurt to re-do these checks during the actual copy-up.For directory reading
ovl_permission()only checks access to topmost underlying layer. Readdir on a merged directory accesses layers below the topmost one as well. Permission wasn't checked for these layers.Note: modifying
ovl_permission()to perform this check would be far more complex and hence more bug prone. The result is less precise permissions returned in access(2). If this turns out to be an issue, we can revisit this bug.Signed-off-by Miklos Szeredi <[email protected]>Signed-off-by Sasha Levin <[email protected]>--- fs/overlayfs/util.c | 27 ++++++++++++++++++++++++++- 1 file changed, 26 insertions(+), 1 deletion(-)fs/overlayfs/util.c +0
-0
fs/overlayfs/util.c bool ovl_is_whiteout(struct dentry *dentry) · line 486
Quoted 9 lines
fs/overlayfs/util.c +5
-1@@ -479,7 +479,32 @@ bool ovl_is_whiteout(struct dentry *dentry)struct file *ovl_path_open (struct path *path,int flags) { -return dentry_open (path, flags |O_NOATIME ,current_cred ()); +struct inode *inode =d_inode (path->dentry); +int err, acc_mode; + +if (flags & ~(O_ACCMODE |O_LARGEFILE )) +BUG ();
This BUG: triggered on stable-rc 5.7, 5.4, 4.19 and 4.14 on arm64 architecture.
steps to reproduce:
- cd /opt/ltp
- ./runltp -s execveat03
tst_device.c:262: INFO: Using test device LTP_DEV='/dev/loop0' tst_mkfs.c:90: INFO: Formatting /dev/loop0 with ext2 opts='' extra opts='' mke2fs 1.43.8 (1-Jan-2018)
[ 407.103235] ------------[ cut here ]------------ [ 407.107890] kernel BUG at fs/overlayfs/util.c:486! [ 407.112704] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP [ 407.118209] Modules linked in: overlay rfkill crc32_ce crct10dif_ce fuse [ 407.124965] Process execveat03 (pid: 17583, stack limit = 0x0000000043f145d5) [ 407.132136] CPU: 5 PID: 17583 Comm: execveat03 Not tainted 4.19.130-rc1-00442-g6c3e013be752 #1 [ 407.140774] Hardware name: ARM Juno development board (r2) (DT) [ 407.146718] pstate: 60000005 (nZCv daif -PAN -UAO) [ 407.151634] pc : ovl_path_open+0xc4/0xc8 [overlay] [ 407.156537] lr : ovl_path_open+0x2c/0xc8 [overlay] [ 407.161345] sp : ffff800909eaf8c0 [ 407.164673] x29: ffff800909eaf8c0 x28: ffff800909eafb40 [ 407.170011] x27: 0000000000000000 x26: ffff2000012de1c0 [ 407.175349] x25: ffff800909785e6c x24: ffff8009042073f0 [ 407.180687] x23: ffff800909eafb40 x22: ffff200009d4d8c8 [ 407.186026] x21: ffff800909eafb40 x20: ffff8008e4e25238 [ 407.191364] x19: 0000000000004000 x18: 0000000000000000 [ 407.196700] x17: 0000000000000000 x16: 0000000000000000 [ 407.202037] x15: 0000000000000000 x14: ffff200008340864 [ 407.207375] x13: ffff20000833f61c x12: ffff20000833b7bc [ 407.212714] x11: ffff20000830c52c x10: ffff2000012c8158 [ 407.218052] x9 : ffff20000830b12c x8 : ffff200008084788 [ 407.223390] x7 : 0000000041b58ab3 x6 : 00000000f1f1f1f1 [ 407.228726] x5 : 00000000f3000000 x4 : dfff200000000000 [ 407.234064] x3 : dfff200000000000 x2 : 0000000000000007 [ 407.239401] x1 : 0000000000004000 x0 : 0000000000000000 [ 407.244736] Call trace: [ 407.247289] ovl_path_open+0xc4/0xc8 [overlay] [ 407.251846] ovl_check_d_type_supported+0x9c/0x178 [overlay] [ 407.257616] ovl_fill_super+0x8d4/0x1ad8 [overlay] [ 407.262437] mount_nodev+0x4c/0xb8 [ 407.265942] ovl_mount+0x18/0x20 [overlay] [ 407.270060] mount_fs+0x64/0x1d8 [ 407.273314] vfs_kern_mount.part.0+0x4c/0x1a0 [ 407.277696] do_mount+0x27c/0x1080 [ 407.281121] ksys_mount+0x8c/0xe8 [ 407.284459] __arm64_sys_mount+0x64/0x80 [ 407.288409] el0_svc_common+0xac/0x1e8 [ 407.292182] el0_svc_handler+0x38/0x80 [ 407.295951] el0_svc+0x8/0xc [ 407.298859] Code: f94013f5 a8c37bfd d65f03c0 d4210000 (d4210000) [ 407.304977] ---[ end trace 50a1985db0cfa610 ]---
https://lkft.validation.linaro.org/scheduler/job/1515127#L3772
metadata:
git branch: linux-4.19.y
git repo: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
git commit: 6c3e013be752bf70e7321d7c813d68eac8ac36b0
git describe: v4.19.128-442-g6c3e013be752
make_kernelversion: 4.19.130-rc1
kernel-config:
https://builds.tuxbuild.com/xGjDe8DWEXpxwsygVrqa6Q/kernel.config
build-url: https://gitlab.com/Linaro/lkft/kernel-runs/-/pipelines/158883698
Signature · 2 lines
Linaro LKFT https://lkft.linaro.org
Sasha Levin
maintainerPATCH 139/172 scsi: iscsi: Fix reference count leak in iscsi_boot_create_kobj
In reply to Sasha LevinFrom: Qiushi Wu <[email protected]>
[ Upstream commit 0267ffce562c8bbf9b57ebe0e38445ad04972890 ]
kobject_init_and_add() takes reference even when it fails. If this function returns an error, kobject_put() must be called to properly clean up the memory associated with the object.
--- drivers/scsi/iscsi_boot_sysfs.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/scsi/iscsi_boot_sysfs.c +1 -1
@@ -360,7 +360,7 @@ iscsi_boot_create_kobj(struct iscsi_boot_kset *boot_kset, boot_kobj->kobj.kset = boot_kset->kset;if (kobject_init_and_add (&boot_kobj->kobj, &iscsi_boot_ktype,NULL , name, index)) { -kfree (boot_kobj); +kobject_put (&boot_kobj->kobj);return NULL ; } boot_kobj->data = data;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 140/172 scsi: ufs: Don't update urgent bkops level when toggling auto bkops
In reply to Sasha LevinFrom: Can Guo <[email protected]>
[ Upstream commit be32acff43800c87dc5c707f5d47cc607b76b653 ]
Urgent bkops level is used to compare against actual bkops status read from UFS device. Urgent bkops level is set during initialization and might be updated in exception event handler during runtime. But it should not be updated to the actual bkops status every time when auto bkops is toggled. Otherwise, if urgent bkops level is updated to 0, auto bkops shall always be kept enabled.
--- drivers/scsi/ufs/ufshcd.c | 1 - 1 file changed, 1 deletion(-)
drivers/scsi/ufs/ufshcd.c +0 -1
@@ -5122,7 +5122,6 @@ static int ufshcd_bkops_ctrl(struct ufs_hba *hba, err =ufshcd_enable_auto_bkops (hba); else err =ufshcd_disable_auto_bkops (hba); - hba->urgent_bkops_lvl = curr_status; out:return err; }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 141/172 pinctrl: imxl: Fix an error handling path in 'imx1_pinctrl_core_probe()'
In reply to Sasha LevinFrom: Christophe JAILLET <[email protected]>
[ Upstream commit 9eb728321286c4b31e964d2377fca2368526d408 ]
When 'pinctrl_register()' has been turned into 'devm_pinctrl_register()', an error handling path has not been updated.
Axe a now unneeded 'pinctrl_unregister()'.
--- drivers/pinctrl/freescale/pinctrl-imx1-core.c | 1 - 1 file changed, 1 deletion(-)
drivers/pinctrl/freescale/pinctrl-imx1-core.c +0 -1
@@ -638,7 +638,6 @@ int imx1_pinctrl_core_probe(struct platform_device *pdev, ret =of_platform_populate (pdev->dev.of_node,NULL ,NULL , &pdev->dev);if (ret) { -pinctrl_unregister (ipctl->pctl);dev_err (&pdev->dev,"Failed to populate subdevices\n" );return ret; }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 142/172 pinctrl: freescale: imx: Fix an error handling path in 'imx_pinctrl_probe()'
In reply to Sasha LevinFrom: Christophe JAILLET <[email protected]>
[ Upstream commit 11d8da5cabf7c6c3263ba2cd9c00260395867048 ]
'pinctrl_unregister()' should not be called to undo 'devm_pinctrl_register_and_init()', it is already handled by the framework.
This simplifies the error handling paths of the probe function. The 'imx_free_resources()' can be removed as well.
--- drivers/pinctrl/freescale/pinctrl-imx.c | 19 ++----------------- 1 file changed, 2 insertions(+), 17 deletions(-)
drivers/pinctrl/freescale/pinctrl-imx.c +2 -17
@@ -662,16 +662,6 @@ static int imx_pinctrl_probe_dt(struct platform_device *pdev,return 0 ; } -/* -* imx_free_resources() - free memory used by this driver -* @info: info driver instance -*/ -static void imx_free_resources (struct imx_pinctrl *ipctl) -{ -if (ipctl->pctl) -pinctrl_unregister (ipctl->pctl); -} -int imx_pinctrl_probe (struct platform_device *pdev,const struct imx_pinctrl_soc_info *info) {
@@ -762,21 +752,16 @@ int imx_pinctrl_probe(struct platform_device *pdev, &ipctl->pctl);if (ret) {dev_err (&pdev->dev,"could not register IMX pinctrl driver\n" ); - goto free; +return ret; } ret =imx_pinctrl_probe_dt (pdev, ipctl);if (ret) {dev_err (&pdev->dev,"fail to probe dt properties\n" ); - goto free; +return ret; }dev_info (&pdev->dev,"initialized IMX pinctrl driver\n" );return pinctrl_enable (ipctl->pctl); - -free: -imx_free_resources (ipctl); - -return ret; }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 143/172 crypto: omap-sham - add proper load balancing support for multicore
In reply to Sasha LevinFrom: Tero Kristo <[email protected]>
[ Upstream commit 281c377872ff5d15d80df25fc4df02d2676c7cde ]
The current implementation of the multiple accelerator core support for OMAP SHA does not work properly. It always picks up the first probed accelerator core if this is available, and rest of the book keeping also gets confused if there are two cores available. Add proper load balancing support for SHA, and also fix any bugs related to the multicore support while doing it.
--- drivers/crypto/omap-sham.c | 64 ++++++++++++++++++-------------------- 1 file changed, 31 insertions(+), 33 deletions(-)
drivers/crypto/omap-sham.c +31 -33
@@ -168,8 +168,6 @@ struct omap_sham_hmac_ctx { };struct omap_sham_ctx { -struct omap_sham_dev *dd; -unsigned long flags;/* fallback stuff */
@@ -921,27 +919,35 @@ static int omap_sham_update_dma_stop(struct omap_sham_dev *dd)return 0 ; } +struct omap_sham_dev *omap_sham_find_dev (struct omap_sham_reqctx *ctx) +{ +struct omap_sham_dev *dd; + +if (ctx->dd) +return ctx->dd; + +spin_lock_bh (&sham.lock); + dd = list_first_entry(&sham.dev_list, struct omap_sham_dev, list); +list_move_tail (&dd->list, &sham.dev_list); + ctx->dd = dd; +spin_unlock_bh (&sham.lock); + +return dd; +} +static int omap_sham_init (struct ahash_request *req) {struct crypto_ahash *tfm =crypto_ahash_reqtfm (req);struct omap_sham_ctx *tctx =crypto_ahash_ctx (tfm);struct omap_sham_reqctx *ctx =ahash_request_ctx (req); -struct omap_sham_dev *dd =NULL , *tmp; +struct omap_sham_dev *dd;int bs =0 ; -spin_lock_bh (&sham.lock); -if (!tctx->dd) { -list_for_each_entry (tmp, &sham.dev_list, list) { - dd = tmp; -break ; - } - tctx->dd = dd; - }else { - dd = tctx->dd; - } -spin_unlock_bh (&sham.lock); + ctx->dd =NULL ; - ctx->dd = dd; + dd =omap_sham_find_dev (ctx); +if (!dd) +return -ENODEV ; ctx->flags =0 ;
@@ -1191,8 +1197,7 @@ static int omap_sham_handle_queue(struct omap_sham_dev *dd,static int omap_sham_enqueue (struct ahash_request *req,unsigned int op) {struct omap_sham_reqctx *ctx =ahash_request_ctx (req); -struct omap_sham_ctx *tctx =crypto_tfm_ctx (req->base.tfm); -struct omap_sham_dev *dd = tctx->dd; +struct omap_sham_dev *dd = ctx->dd; ctx->op = op;
@@ -1202,7 +1207,7 @@ static int omap_sham_enqueue(struct ahash_request *req, unsigned int op)static int omap_sham_update (struct ahash_request *req) {struct omap_sham_reqctx *ctx =ahash_request_ctx (req); -struct omap_sham_dev *dd = ctx->dd; +struct omap_sham_dev *dd =omap_sham_find_dev (ctx);if (!req->nbytes)return 0 ;
@@ -1307,21 +1312,8 @@ static int omap_sham_setkey(struct crypto_ahash *tfm, const u8 *key,struct omap_sham_hmac_ctx *bctx = tctx->base;int bs =crypto_shash_blocksize (bctx->shash);int ds =crypto_shash_digestsize (bctx->shash); -struct omap_sham_dev *dd =NULL , *tmp;int err, i; -spin_lock_bh (&sham.lock); -if (!tctx->dd) { -list_for_each_entry (tmp, &sham.dev_list, list) { - dd = tmp; -break ; - } - tctx->dd = dd; - }else { - dd = tctx->dd; - } -spin_unlock_bh (&sham.lock); - err =crypto_shash_setkey (tctx->fallback, key, keylen);if (err)return err;
@@ -1339,7 +1331,7 @@ static int omap_sham_setkey(struct crypto_ahash *tfm, const u8 *key,memset (bctx->ipad + keylen,0 , bs - keylen); -if (!test_bit (FLAGS_AUTO_XOR , &dd->flags)) { +if (!test_bit (FLAGS_AUTO_XOR , &sham.flags)) {memcpy (bctx->opad, bctx->ipad, bs);for (i =0 ; i < bs; i++) {
@@ -2142,6 +2134,7 @@ static int omap_sham_probe(struct platform_device *pdev) } dd->flags |= dd->pdata->flags; + sham.flags |= dd->pdata->flags;pm_runtime_use_autosuspend (dev);pm_runtime_set_autosuspend_delay (dev,DEFAULT_AUTOSUSPEND_DELAY );
@@ -2169,6 +2162,9 @@ static int omap_sham_probe(struct platform_device *pdev)spin_unlock (&sham.lock);for (i =0 ; i < dd->pdata->algs_info_size; i++) { +if (dd->pdata->algs_info[i].registered) +break ; +for (j =0 ; j < dd->pdata->algs_info[i].size; j++) {struct ahash_alg *alg;
@@ -2220,9 +2216,11 @@ static int omap_sham_remove(struct platform_device *pdev)list_del (&dd->list);spin_unlock (&sham.lock);for (i = dd->pdata->algs_info_size -1 ; i >=0 ; i--) -for (j = dd->pdata->algs_info[i].registered -1 ; j >=0 ; j--) +for (j = dd->pdata->algs_info[i].registered -1 ; j >=0 ; j--) {crypto_unregister_ahash ( &dd->pdata->algs_info[i].algs_list[j]); + dd->pdata->algs_info[i].registered--; + }tasklet_kill (&dd->done_task);pm_runtime_disable (&pdev->dev);
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 144/172 geneve: change from tx_error to tx_dropped on missing metadata
In reply to Sasha LevinFrom: Jiri Benc <[email protected]>
[ Upstream commit 9d149045b3c0e44c049cdbce8a64e19415290017 ]
If the geneve interface is in collect_md (external) mode, it can't send any packets submitted directly to its net interface, as such packets won't have metadata attached. This is expected.
However, the kernel itself sends some packets to the interface, most notably, IPv6 DAD, IPv6 multicast listener reports, etc. This is not wrong, as tunnel metadata can be specified in routing table (although technically, that has never worked for IPv6, but hopefully will be fixed eventually) and then the interface must correctly participate in IPv6 housekeeping.
The problem is that any such attempt increases the tx_error counter. Just bringing up a geneve interface with IPv6 enabled is enough to see a number of tx_errors. That causes confusion among users, prompting them to find a network error where there is none.
Change the counter used to tx_dropped. That better conveys the meaning (there's nothing wrong going on, just some packets are getting dropped) and hopefully will make admins panic less.
--- drivers/net/geneve.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/net/geneve.c +4 -3
@@ -911,9 +911,10 @@ static netdev_tx_t geneve_xmit(struct sk_buff *skb, struct net_device *dev)if (geneve->collect_md) { info =skb_tunnel_info (skb);if (unlikely (!info || !(info->mode &IP_TUNNEL_INFO_TX ))) { - err = -EINVAL ;netdev_dbg (dev,"no tunnel metadata\n" ); - goto tx_error; +dev_kfree_skb (skb); + dev->stats.tx_dropped++; +return NETDEV_TX_OK ; } }else { info = &geneve->info;
@@ -930,7 +931,7 @@ static netdev_tx_t geneve_xmit(struct sk_buff *skb, struct net_device *dev)if (likely (!err))return NETDEV_TX_OK ; -tx_error: +dev_kfree_skb (skb);if (err == -ELOOP )
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 145/172 lib/zlib: remove outdated and incorrect pre-increment optimization
In reply to Sasha LevinFrom: Jann Horn <[email protected]>
[ Upstream commit acaab7335bd6f0c0b54ce3a00bd7f18222ce0f5f ]
The zlib inflate code has an old micro-optimization based on the assumption that for pre-increment memory accesses, the compiler will generate code that fits better into the processor's pipeline than what would be generated for post-increment memory accesses.
This optimization was already removed in upstream zlib in 2016:
https://github.com/madler/zlib/commit/9aaec95e8211
This optimization causes UB according to C99, which says in section 6.5.6 "Additive operators": "If both the pointer operand and the result point to elements of the same array object, or one past the last element of the array object, the evaluation shall not produce an overflow; otherwise, the behavior is undefined".
This UB is not only a theoretical concern, but can also cause trouble for future work on compiler-based sanitizers.
According to the zlib commit, this optimization also is not optimal anymore with modern compilers.
Replace uses of OFF, PUP and UP_UNALIGNED with their definitions in the POSTINC case, and remove the macro definitions, just like in the upstream patch.
--- lib/zlib_inflate/inffast.c | 91 +++++++++++++++----------------------- 1 file changed, 35 insertions(+), 56 deletions(-)
lib/zlib_inflate/inffast.c +35 -56
@@ -10,17 +10,6 @@ #ifndef ASMINF -/* Allow machine dependent optimization for post-increment or pre-increment. - Based on testing to date, - Pre-increment preferred for: - - PowerPC G3 (Adler) - - MIPS R5000 (Randers-Pehrson) - Post-increment preferred for: - - none - No measurable difference: - - Pentium III (Anderson) - - M68060 (Nikl) - */ union uu { unsigned short us; unsigned char b[2];
@@ -38,16 +27,6 @@ get_unaligned16(const unsigned short *p)return mm.us; } -#ifdef POSTINC -# define OFF 0 -# define PUP (a) *(a)++ -# define UP_UNALIGNED (a) get_unaligned16((a)++) -#else -# define OFF 1 -# define PUP (a) *++(a) -# define UP_UNALIGNED (a) get_unaligned16(++(a)) -#endif -/* Decode literal, length, and distance codes and write out the resulting literal and match bytes until either not enough input or output is
@@ -115,9 +94,9 @@ void inflate_fast(z_streamp strm, unsigned start)/* copy state to local variables */ state = (struct inflate_state *)strm->state; - in = strm->next_in -OFF ; + in = strm->next_in; last = in + (strm->avail_in -5 ); - out = strm->next_out -OFF ; + out = strm->next_out; beg = out - (start - strm->avail_out); end = out + (strm->avail_out -257 );#ifdef INFLATE_STRICT
@@ -138,9 +117,9 @@ void inflate_fast(z_streamp strm, unsigned start)input data or output space */ do { if (bits < 15) { - hold += (unsigned long)(PUP(in)) << bits; + hold += (unsigned long)(*in++) << bits; bits += 8; - hold += (unsigned long)(PUP(in)) << bits; + hold += (unsigned long)(*in++) << bits; bits += 8; } this = lcode[hold & lmask];
@@ -150,14 +129,14 @@ void inflate_fast(z_streamp strm, unsigned start) bits -= op; op = (unsigned )(this.op);if (op ==0 ) {/* literal */ -PUP (out) = (unsigned char )(this.val); + *out++ = (unsigned char )(this.val); }else if (op &16 ) {/* length base */ len = (unsigned )(this.val); op &=15 ;/* number of extra bits */ if (op) {if (bits < op) { - hold += (unsigned long )(PUP (in)) << bits; + hold += (unsigned long )(*in++) << bits; bits +=8 ; } len += (unsigned )hold & ((1U << op) -1 );
@@ -165,9 +144,9 @@ void inflate_fast(z_streamp strm, unsigned start) bits -= op; }if (bits <15 ) { - hold += (unsigned long )(PUP (in)) << bits; + hold += (unsigned long )(*in++) << bits; bits +=8 ; - hold += (unsigned long )(PUP (in)) << bits; + hold += (unsigned long )(*in++) << bits; bits +=8 ; } this = dcode[hold & dmask];
@@ -180,10 +159,10 @@ void inflate_fast(z_streamp strm, unsigned start) dist = (unsigned )(this.val); op &=15 ;/* number of extra bits */ if (bits < op) { - hold += (unsigned long )(PUP (in)) << bits; + hold += (unsigned long )(*in++) << bits; bits +=8 ;if (bits < op) { - hold += (unsigned long )(PUP (in)) << bits; + hold += (unsigned long )(*in++) << bits; bits +=8 ; } }
@@ -205,13 +184,13 @@ void inflate_fast(z_streamp strm, unsigned start) state->mode =BAD ;break ; } - from = window -OFF ; + from = window;if (write ==0 ) {/* very common case */ from += wsize - op;if (op < len) {/* some from window */ len -= op;do { -PUP (out) =PUP (from); + *out++ = *from++; }while (--op); from = out - dist;/* rest from output */ }
@@ -222,14 +201,14 @@ void inflate_fast(z_streamp strm, unsigned start)if (op < len) {/* some from end of window */ len -= op;do { -PUP (out) =PUP (from); + *out++ = *from++; }while (--op); - from = window -OFF ; + from = window;if (write < len) {/* some from start of window */ op = write; len -= op;do { -PUP (out) =PUP (from); + *out++ = *from++; }while (--op); from = out - dist;/* rest from output */ }
@@ -240,21 +219,21 @@ void inflate_fast(z_streamp strm, unsigned start)if (op < len) {/* some from window */ len -= op;do { -PUP (out) =PUP (from); + *out++ = *from++; }while (--op); from = out - dist;/* rest from output */ } }while (len >2 ) { -PUP (out) =PUP (from); -PUP (out) =PUP (from); -PUP (out) =PUP (from); + *out++ = *from++; + *out++ = *from++; + *out++ = *from++; len -=3 ; }if (len) { -PUP (out) =PUP (from); + *out++ = *from++;if (len >1 ) -PUP (out) =PUP (from); + *out++ = *from++; } }else {
@@ -264,29 +243,29 @@ void inflate_fast(z_streamp strm, unsigned start) from = out - dist;/* copy direct from output */ /* minimum length is three */ /* Align out addr */ -if (!((long )(out -1 +OFF ) &1 )) { -PUP (out) =PUP (from); +if (!((long )(out -1 ) &1 )) { + *out++ = *from++; len--; } - sout = (unsigned short *)(out -OFF ); + sout = (unsigned short *)(out);if (dist >2 ) {unsigned short *sfrom; - sfrom = (unsigned short *)(from -OFF ); + sfrom = (unsigned short *)(from); loops = len >>1 ; do#ifdef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS -PUP (sout) =PUP (sfrom); + *sout++ = *sfrom++;#else -PUP (sout) =UP_UNALIGNED (sfrom); + *sout++ =get_unaligned16 (sfrom++);#endif while (--loops); - out = (unsigned char *)sout +OFF ; - from = (unsigned char *)sfrom +OFF ; + out = (unsigned char *)sout; + from = (unsigned char *)sfrom; }else {/* dist == 1 or dist == 2 */ unsigned short pat16; - pat16 = *(sout-1 +OFF ); + pat16 = *(sout-1 );if (dist ==1 ) {union uu mm;/* copy one char pattern to both bytes */
@@ -296,12 +275,12 @@ void inflate_fast(z_streamp strm, unsigned start) } loops = len >>1 ;do -PUP (sout) = pat16; + *sout++ = pat16;while (--loops); - out = (unsigned char *)sout +OFF ; + out = (unsigned char *)sout; }if (len &1 ) -PUP (out) =PUP (from); + *out++ = *from++; } }else if ((op &64 ) ==0 ) {/* 2nd level distance code */
@@ -336,8 +315,8 @@ void inflate_fast(z_streamp strm, unsigned start) hold &= (1U << bits) -1 ;/* update state and return */ - strm->next_in = in +OFF ; - strm->next_out = out +OFF ; + strm->next_in = in; + strm->next_out = out; strm->avail_in = (unsigned )(in < last ?5 + (last - in) :5 - (in - last)); strm->avail_out = (unsigned )(out < end ?257 + (end - out) :257 - (out - end));
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 146/172 include/linux/bitops.h: avoid clang shift-count-overflow warnings
In reply to Sasha LevinFrom: Arnd Bergmann <[email protected]>
[ Upstream commit bd93f003b7462ae39a43c531abca37fe7073b866 ]
Clang normally does not warn about certain issues in inline functions when it only happens in an eliminated code path. However if something else goes wrong, it does tend to complain about the definition of hweight_long() on 32-bit targets:
include/linux/bitops.h:75:41: error: shift count >= width of type [-Werror,-Wshift-count-overflow]
return sizeof(w) == 4 ? hweight32(w) : hweight64(w);
^~~~~~~~~~~~
include/asm-generic/bitops/const_hweight.h:29:49: note: expanded from macro 'hweight64'
define hweight64(w) (__builtin_constant_p(w) ? __const_hweight64(w) : __arch_hweight64(w))
^~~~~~~~~~~~~~~~~~~~
include/asm-generic/bitops/const_hweight.h:21:76: note: expanded from macro '__const_hweight64'
define __const_hweight64(w) (__const_hweight32(w) + __const_hweight32((w) >> 32))
^ ~~
include/asm-generic/bitops/const_hweight.h:20:49: note: expanded from macro '__const_hweight32'
define __const_hweight32(w) (__const_hweight16(w) + __const_hweight16((w) >> 16))
^
include/asm-generic/bitops/const_hweight.h:19:72: note: expanded from macro '__const_hweight16'
define __const_hweight16(w) (__const_hweight8(w) + __const_hweight8((w) >> 8 ))
^
include/asm-generic/bitops/const_hweight.h:12:9: note: expanded from macro '__const_hweight8'
(!!((w) & (1ULL << 2))) + \Adding an explicit cast to __u64 avoids that warning and makes it easier to read other output.
--- include/linux/bitops.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
include/linux/bitops.h +1 -1
@@ -50,7 +50,7 @@ static inline int get_bitmask_order(unsigned int count)static __always_inline unsigned long hweight_long (unsigned long w) { -return sizeof (w) ==4 ?hweight32 (w) :hweight64 (w); +return sizeof (w) ==4 ?hweight32 (w) :hweight64 ((__u64 )w); }/**
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 147/172 elfnote: mark all .note sections SHF_ALLOC
In reply to Sasha LevinFrom: Nick Desaulniers <[email protected]>
[ Upstream commit 51da9dfb7f20911ae4e79e9b412a9c2d4c373d4b ]
ELFNOTE_START allows callers to specify flags for .pushsection assembler directives. All callsites but ELF_NOTE use "a" for SHF_ALLOC. For vdso's that explicitly use ELF_NOTE_START and BUILD_SALT, the same section is specified twice after preprocessing, once with "a" flag, once without. Example:
.pushsection .note.Linux, "a", @note ;
.pushsection .note.Linux, "", @note ;
While GNU as allows this ordering, it warns for the opposite ordering, making these directives position dependent. We'd prefer not to precisely match this behavior in Clang's integrated assembler. Instead, the non __ASSEMBLY__ definition of ELF_NOTE uses __attribute__((section(".note.Linux"))) which is created with SHF_ALLOC, so let's make the __ASSEMBLY__ definition of ELF_NOTE consistent with C and just always use "a" flag.
This allows Clang to assemble a working mainline (5.6) kernel via:
$ make CC=clang AS=clang
--- include/linux/elfnote.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
include/linux/elfnote.h +1 -1
@@ -54,7 +54,7 @@ .popsection ;#define ELFNOTE (name, type, desc) \ - ELFNOTE_START(name, type, "") \ + ELFNOTE_START(name, type, "a") \ desc ; \ ELFNOTE_END
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 148/172 selftests/vm/pkeys: fix alloc_random_pkey() to make it really random
In reply to Sasha LevinFrom: Ram Pai <[email protected]>
[ Upstream commit 6e373263ce07eeaa6410843179535fbdf561fc31 ]
alloc_random_pkey() was allocating the same pkey every time. Not all pkeys were geting tested. This fixes it.
--- tools/testing/selftests/x86/protection_keys.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
tools/testing/selftests/x86/protection_keys.c +2 -1
@@ -24,6 +24,7 @@#define _GNU_SOURCE#include <errno.h> #include <linux/futex.h> +#include <time.h> #include <sys/time.h> #include <sys/syscall.h> #include <string.h>
@@ -612,10 +613,10 @@ int alloc_random_pkey(void)int nr_alloced =0 ;int random_index;memset (alloced_pkeys,0 ,sizeof (alloced_pkeys)); +srand ((unsigned int )time (NULL ));/* allocate every possible key and make a note of which ones we got */ max_nr_pkey_allocs =NR_PKEYS ; - max_nr_pkey_allocs =1 ;for (i =0 ; i < max_nr_pkey_allocs; i++) {int new_pkey =alloc_pkey ();if (new_pkey <0 )
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 149/172 blktrace: use errno instead of bi_status
In reply to Sasha LevinFrom: Chaitanya Kulkarni <[email protected]>
[ Upstream commit 48bc3cd3e07a1486f45d9971c75d6090976c3b1b ]
In blk_add_trace_spliti() blk_add_trace_bio_remap() use blk_status_to_errno() to pass the error instead of pasing the bi_status. This fixes the sparse warning.
--- kernel/trace/blktrace.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-)
kernel/trace/blktrace.c +6 -3
@@ -1004,8 +1004,10 @@ static void blk_add_trace_split(void *ignore,__blk_add_trace (bt, bio->bi_iter.bi_sector, bio->bi_iter.bi_size,bio_op (bio), bio->bi_opf, -BLK_TA_SPLIT , bio->bi_status,sizeof (rpdu), - &rpdu,blk_trace_bio_get_cgid (q, bio)); +BLK_TA_SPLIT , +blk_status_to_errno (bio->bi_status), +sizeof (rpdu), &rpdu, +blk_trace_bio_get_cgid (q, bio)); }rcu_read_unlock (); }
@@ -1042,7 +1044,8 @@ static void blk_add_trace_bio_remap(void *ignore, r.sector_from =cpu_to_be64 (from);__blk_add_trace (bt, bio->bi_iter.bi_sector, bio->bi_iter.bi_size, -bio_op (bio), bio->bi_opf,BLK_TA_REMAP , bio->bi_status, +bio_op (bio), bio->bi_opf,BLK_TA_REMAP , +blk_status_to_errno (bio->bi_status),sizeof (r), &r,blk_trace_bio_get_cgid (q, bio));rcu_read_unlock (); }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 150/172 blktrace: fix endianness in get_pdu_int()
In reply to Sasha LevinFrom: Chaitanya Kulkarni <[email protected]>
[ Upstream commit 71df3fd82e7cccec7b749a8607a4662d9f7febdd ]
In function get_pdu_len() replace variable type from __u64 to __be64. This fixes sparse warning.
--- kernel/trace/blktrace.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
kernel/trace/blktrace.c +1 -1
@@ -1267,7 +1267,7 @@ static inline __u16 t_error(const struct trace_entry *ent)static __u64 get_pdu_int (const struct trace_entry *ent,bool has_cg) { -const __u64 *val =pdu_start (ent, has_cg); +const __be64 *val =pdu_start (ent, has_cg);return be64_to_cpu (*val); }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 151/172 blktrace: fix endianness for blk_log_remap()
In reply to Sasha LevinFrom: Chaitanya Kulkarni <[email protected]>
[ Upstream commit 5aec598c456fe3c1b71a1202cbb42bdc2a643277 ]
The function blk_log_remap() can be simplified by removing the call to get_pdu_remap() that copies the values into extra variable to print the data, which also fixes the endiannness warning reported by sparse.
--- kernel/trace/blktrace.c | 19 ++++--------------- 1 file changed, 4 insertions(+), 15 deletions(-)
kernel/trace/blktrace.c +4 -15
@@ -1271,17 +1271,6 @@ static __u64 get_pdu_int(const struct trace_entry *ent, bool has_cg)return be64_to_cpu (*val); } -static void get_pdu_remap (const struct trace_entry *ent, -struct blk_io_trace_remap *r,bool has_cg) -{ -const struct blk_io_trace_remap *__r =pdu_start (ent, has_cg); -__u64 sector_from = __r->sector_from; - - r->device_from =be32_to_cpu (__r->device_from); - r->device_to =be32_to_cpu (__r->device_to); - r->sector_from =be64_to_cpu (sector_from); -} -typedef void (blk_log_action_t ) (struct trace_iterator *iter,const char *act,bool has_cg);
@@ -1407,13 +1396,13 @@ static void blk_log_with_error(struct trace_seq *s,static void blk_log_remap (struct trace_seq *s,const struct trace_entry *ent,bool has_cg) { -struct blk_io_trace_remap r = { .device_from =0 , }; +const struct blk_io_trace_remap *__r =pdu_start (ent, has_cg); -get_pdu_remap (ent, &r, has_cg);trace_seq_printf (s,"%llu + %u <- (%d,%d) %llu\n" ,t_sector (ent),t_sec (ent), -MAJOR (r.device_from),MINOR (r.device_from), - (unsigned long long )r.sector_from); +MAJOR (be32_to_cpu (__r->device_from)), +MINOR (be32_to_cpu (__r->device_from)), +be64_to_cpu (__r->sector_from)); }static void blk_log_plug (struct trace_seq *s,const struct trace_entry *ent,bool has_cg)
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 152/172 gfs2: fix use-after-free on transaction ail lists
In reply to Sasha LevinFrom: Bob Peterson <[email protected]>
[ Upstream commit 83d060ca8d90fa1e3feac227f995c013100862d3 ]
Before this patch, transactions could be merged into the system transaction by function gfs2_merge_trans(), but the transaction ail lists were never merged. Because the ail flushing mechanism can run separately, bd elements can be attached to the transaction's buffer list during the transaction (trans_add_meta, etc) but quickly moved to its ail lists. Later, in function gfs2_trans_end, the transaction can be freed (by gfs2_trans_end) while it still has bd elements queued to its ail lists, which can cause it to either lose track of the bd elements altogether (memory leak) or worse, reference the bd elements after the parent transaction has been freed.
Although I've not seen any serious consequences, the problem becomes apparent with the previous patch's addition of:
gfs2_assert_warn(sdp, list_empty(&tr->tr_ail1_list));
to function gfs2_trans_free().
This patch adds logic into gfs2_merge_trans() to move the merged transaction's ail lists to the sdp transaction. This prevents the use-after-free. To do this properly, we need to hold the ail lock, so we pass sdp into the function instead of the transaction itself.
--- fs/gfs2/log.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-)
fs/gfs2/log.c +9 -2
@@ -877,8 +877,10 @@ void gfs2_log_flush(struct gfs2_sbd *sdp, struct gfs2_glock *gl, u32 flags)* @new: New transaction to be merged */ -static void gfs2_merge_trans (struct gfs2_trans *old,struct gfs2_trans *new) +static void gfs2_merge_trans (struct gfs2_sbd *sdp,struct gfs2_trans *new) { +struct gfs2_trans *old = sdp->sd_log_tr; +WARN_ON_ONCE (!test_bit (TR_ATTACHED , &old->tr_flags)); old->tr_num_buf_new += new->tr_num_buf_new;
@@ -890,6 +892,11 @@ static void gfs2_merge_trans(struct gfs2_trans *old, struct gfs2_trans *new)list_splice_tail_init (&new->tr_databuf, &old->tr_databuf);list_splice_tail_init (&new->tr_buf, &old->tr_buf); + +spin_lock (&sdp->sd_ail_lock); +list_splice_tail_init (&new->tr_ail1_list, &old->tr_ail1_list); +list_splice_tail_init (&new->tr_ail2_list, &old->tr_ail2_list); +spin_unlock (&sdp->sd_ail_lock); }static void log_refund (struct gfs2_sbd *sdp,struct gfs2_trans *tr)
@@ -901,7 +908,7 @@ static void log_refund(struct gfs2_sbd *sdp, struct gfs2_trans *tr)gfs2_log_lock (sdp);if (sdp->sd_log_tr) { -gfs2_merge_trans (sdp->sd_log_tr, tr); +gfs2_merge_trans (sdp, tr); }else if (tr->tr_num_buf_new || tr->tr_num_databuf_new) {gfs2_assert_withdraw (sdp,test_bit (TR_ALLOCED , &tr->tr_flags)); sdp->sd_log_tr = tr;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 153/172 ntb_perf: pass correct struct device to dma_alloc_coherent
In reply to Sasha LevinFrom: Sanjay R Mehta <[email protected]>
[ Upstream commit 98f4e140264eeb52f22ff05be6b6dd48237255ac ]
Currently, ntb->dev is passed to dma_alloc_coherent and dma_free_coherent calls. The returned dma_addr_t is the CPU physical address. This works fine as long as IOMMU is disabled. But when IOMMU is enabled, we need to make sure that IOVA is returned for dma_addr_t. So the correct way to achieve this is by changing the first parameter of dma_alloc_coherent() as ntb->pdev->dev instead.
--- drivers/ntb/test/ntb_perf.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/ntb/test/ntb_perf.c +4 -4
@@ -559,7 +559,7 @@ static void perf_free_inbuf(struct perf_peer *peer)return ; (void )ntb_mw_clear_trans (peer->perf->ntb, peer->pidx, peer->gidx); -dma_free_coherent (&peer->perf->ntb->dev, peer->inbuf_size, +dma_free_coherent (&peer->perf->ntb->pdev->dev, peer->inbuf_size, peer->inbuf, peer->inbuf_xlat); peer->inbuf =NULL ; }
@@ -588,8 +588,9 @@ static int perf_setup_inbuf(struct perf_peer *peer)perf_free_inbuf (peer); - peer->inbuf =dma_alloc_coherent (&perf->ntb->dev, peer->inbuf_size, - &peer->inbuf_xlat,GFP_KERNEL ); + peer->inbuf =dma_alloc_coherent (&perf->ntb->pdev->dev, + peer->inbuf_size, &peer->inbuf_xlat, +GFP_KERNEL );if (!peer->inbuf) {dev_err (&perf->ntb->dev,"Failed to alloc inbuf of %pa\n" , &peer->inbuf_size);
@@ -1512,4 +1513,3 @@ static void __exit perf_exit(void)destroy_workqueue (perf_wq); }module_exit (perf_exit); -
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 154/172 ntb_tool: pass correct struct device to dma_alloc_coherent
In reply to Sasha LevinFrom: Sanjay R Mehta <[email protected]>
[ Upstream commit 433efe720674efd9fdbcef78be75793393cf05db ]
Currently, ntb->dev is passed to dma_alloc_coherent and dma_free_coherent calls. The returned dma_addr_t is the CPU physical address. This works fine as long as IOMMU is disabled. But when IOMMU is enabled, we need to make sure that IOVA is returned for dma_addr_t. So the correct way to achieve this is by changing the first parameter of dma_alloc_coherent() as ntb->pdev->dev instead.
--- drivers/ntb/test/ntb_tool.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/ntb/test/ntb_tool.c +3 -3
@@ -590,7 +590,7 @@ static int tool_setup_mw(struct tool_ctx *tc, int pidx, int widx, inmw->size =min_t (resource_size_t, req_size, size); inmw->size =round_up (inmw->size, addr_align); inmw->size =round_up (inmw->size, size_align); - inmw->mm_base =dma_alloc_coherent (&tc->ntb->dev, inmw->size, + inmw->mm_base =dma_alloc_coherent (&tc->ntb->pdev->dev, inmw->size, &inmw->dma_base,GFP_KERNEL );if (!inmw->mm_base)return -ENOMEM ;
@@ -612,7 +612,7 @@ static int tool_setup_mw(struct tool_ctx *tc, int pidx, int widx,return 0 ; err_free_dma: -dma_free_coherent (&tc->ntb->dev, inmw->size, inmw->mm_base, +dma_free_coherent (&tc->ntb->pdev->dev, inmw->size, inmw->mm_base, inmw->dma_base); inmw->mm_base =NULL ; inmw->dma_base =0 ;
@@ -629,7 +629,7 @@ static void tool_free_mw(struct tool_ctx *tc, int pidx, int widx)if (inmw->mm_base !=NULL ) {ntb_mw_clear_trans (tc->ntb, pidx, widx); -dma_free_coherent (&tc->ntb->dev, inmw->size, +dma_free_coherent (&tc->ntb->pdev->dev, inmw->size, inmw->mm_base, inmw->dma_base); }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 155/172 NTB: ntb_tool: reading the link file should not end in a NULL byte
In reply to Sasha LevinFrom: Logan Gunthorpe <[email protected]>
[ Upstream commit 912e12813dd03c602e4922fc34709ec4d4380cf0 ]
When running ntb_test this warning is issued:
./ntb_test.sh: line 200: warning: command substitution: ignored null byte in input
This is caused by the kernel returning one more byte than is necessary when reading the link file.
Reduce the number of bytes read back to 2 as it was before the commit that regressed this.
--- drivers/ntb/test/ntb_tool.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/ntb/test/ntb_tool.c +1 -2
@@ -504,7 +504,7 @@ static ssize_t tool_peer_link_read(struct file *filep, char __user *ubuf, buf[1 ] ='\n' ; buf[2 ] ='\0' ; -return simple_read_from_buffer (ubuf, size, offp, buf,3 ); +return simple_read_from_buffer (ubuf, size, offp, buf,2 ); } static TOOL_FOPS_RDWR(tool_peer_link_fops,
@@ -1690,4 +1690,3 @@ static void __exit tool_exit(void)debugfs_remove_recursive (tool_dbgfs_topdir); }module_exit (tool_exit); -
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 156/172 NTB: Revert the change to use the NTB device dev for DMA allocations
In reply to Sasha LevinFrom: Logan Gunthorpe <[email protected]>
[ Upstream commit 40da7d9a93c8941737ef4a1208d32c13ce017fe1 ]
Commit 417cf39cfea9 ("NTB: Set dma mask and dma coherent mask to NTB devices") started using the NTB device for DMA allocations which was turns out was wrong. If the IOMMU is enabled, such alloctanions will always fail with messages such as:
DMAR: Allocating domain for 0000:02:00.1 failed
This is because the IOMMU has not setup the device for such use.
Change the tools back to using the PCI device for allocations seeing it doesn't make sense to add an IOMMU group for the non-physical NTB device. Also remove the code that sets the DMA mask as it no longer makes sense to do this.
--- drivers/ntb/ntb.c | 1 - 1 file changed, 1 deletion(-)
drivers/ntb/ntb.c +0 -1
@@ -311,4 +311,3 @@ static void __exit ntb_driver_exit(void)bus_unregister (&ntb_bus); }module_exit (ntb_driver_exit); -
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 157/172 NTB: perf: Don't require one more memory window than number of peers
In reply to Sasha LevinFrom: Logan Gunthorpe <[email protected]>
[ Upstream commit a9c4211ac918ade1522aced6b5acfbe824722f7d ]
ntb_perf should not require more than one memory window per peer. This was probably an off-by-one error.
--- drivers/ntb/test/ntb_perf.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/ntb/test/ntb_perf.c +1 -1
@@ -656,7 +656,7 @@ static int perf_init_service(struct perf_ctx *perf) {u64 mask; -if (ntb_peer_mw_count (perf->ntb) < perf->pcnt +1 ) { +if (ntb_peer_mw_count (perf->ntb) < perf->pcnt) {dev_err (&perf->ntb->dev,"Not enough memory windows\n" );return -EINVAL ; }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 158/172 NTB: perf: Fix support for hardware that doesn't have port numbers
In reply to Sasha LevinFrom: Logan Gunthorpe <[email protected]>
[ Upstream commit b54369a248c2e033bfcf5d6917e08cf9d73d54a6 ]
Legacy drivers do not have port numbers (but is reliably only two ports) and was broken by the recent commit that added mult-port support to ntb_perf. This is especially important to support the cross link topology which is perfectly symmetric and cannot assign unique port numbers easily.
Hardware that returns zero for both the local port and the peer should just always use gidx=0 for the only peer.
--- drivers/ntb/test/ntb_perf.c | 10 ++++++++++ 1 file changed, 10 insertions(+)
drivers/ntb/test/ntb_perf.c +10 -0
@@ -1418,6 +1418,16 @@ static int perf_init_peers(struct perf_ctx *perf)if (perf->gidx ==-1 ) perf->gidx = pidx; +/* +* Hardware with only two ports may not have unique port +* numbers. In this case, the gidxs should all be zero. +*/ +if (perf->pcnt ==1 &&ntb_port_number (perf->ntb) ==0 && +ntb_peer_port_number (perf->ntb,0 ) ==0 ) { + perf->gidx =0 ; + perf->peers[0 ].gidx =0 ; + } +for (pidx =0 ; pidx < perf->pcnt; pidx++) { ret =perf_setup_peer_mw (&perf->peers[pidx]);if (ret)
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 159/172 NTB: perf: Fix race condition when run with ntb_test
In reply to Sasha LevinFrom: Logan Gunthorpe <[email protected]>
[ Upstream commit 34d8673a01b053b6231a995a4eec9341163d63be ]
When running ntb_test, the script tries to run the ntb_perf test immediately after probing the modules. Since adding multi-port support, this fails seeing the new initialization procedure in ntb_perf can not complete instantly.
To fix this we add a completion which is waited on when a test is started. In this way, run can be written any time after the module is loaded and it will wait for the initialization to complete instead of sending an error.
--- drivers/ntb/test/ntb_perf.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-)
drivers/ntb/test/ntb_perf.c +8 -2
@@ -158,6 +158,8 @@ struct perf_peer {/* NTB connection setup service */ struct work_struct service;unsigned long sts; + +struct completion init_comp; };#define to_peer_service (__work) \ container_of(__work, struct perf_peer, service)
@@ -549,6 +551,7 @@ static int perf_setup_outbuf(struct perf_peer *peer)/* Initialization is finally done */ set_bit (PERF_STS_DONE , &peer->sts); +complete_all (&peer->init_comp);return 0 ; }
@@ -640,6 +643,7 @@ static void perf_service_work(struct work_struct *work)perf_setup_outbuf (peer);if (test_and_clear_bit (PERF_CMD_CLEAR , &peer->sts)) { +init_completion (&peer->init_comp);clear_bit (PERF_STS_DONE , &peer->sts);if (test_bit (0 , &peer->perf->busy_flag) && peer == peer->perf->test_peer) {
@@ -1047,8 +1051,9 @@ static int perf_submit_test(struct perf_peer *peer)struct perf_thread *pthr;int tidx, ret; -if (!test_bit (PERF_STS_DONE , &peer->sts)) -return -ENOLINK ; + ret =wait_for_completion_interruptible (&peer->init_comp); +if (ret <0 ) +return ret;if (test_and_set_bit_lock (0 , &perf->busy_flag))return -EBUSY ;
@@ -1414,6 +1419,7 @@ static int perf_init_peers(struct perf_ctx *perf) peer->gidx = pidx; }INIT_WORK (&peer->service, perf_service_work); +init_completion (&peer->init_comp); }if (perf->gidx ==-1 ) perf->gidx = pidx;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 160/172 NTB: ntb_test: Fix bug when counting remote files
In reply to Sasha LevinFrom: Logan Gunthorpe <[email protected]>
[ Upstream commit 2130c0ba69d69bb21f5c52787f2587db00d13d8a ]
When remote files are counted in get_files_count, without using SSH, the code returns 0 because there is a colon prepended to $LOC. $VPATH should have been used instead of $LOC.
--- tools/testing/selftests/ntb/ntb_test.sh | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
tools/testing/selftests/ntb/ntb_test.sh +1 -1
@@ -250,7 +250,7 @@ function get_files_count() split_remote $LOC if [[ "$REMOTE" == "" ]]; then - echo $(ls -1 "$LOC"/${NAME}* 2>/dev/null | wc -l) + echo $(ls -1 "$VPATH"/${NAME}* 2>/dev/null | wc -l) else echo $(ssh "$REMOTE" "ls -1 \"$VPATH\"/${NAME}* | \ wc -l" 2> /dev/null)
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 161/172 drivers/perf: hisi: Fix wrong value for all counters enable
In reply to Sasha LevinFrom: Shaokun Zhang <[email protected]>
[ Upstream commit 961abd78adcb4c72c343fcd9f9dc5e2ebbe9b448 ]
In L3C uncore PMU drivers, bit16 is used to control all counters enable & disable. Wrong value is given in the driver and its default value is 1'b1, it can work because each PMU counter has its own control bits too. Let's fix the wrong value.
--- drivers/perf/hisilicon/hisi_uncore_l3c_pmu.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/perf/hisilicon/hisi_uncore_l3c_pmu.c +1 -1
@@ -38,7 +38,7 @@/* L3C has 8-counters */ #define L3C_NR_COUNTERS 0x8 -#define L3C_PERF_CTRL_EN 0x20000 +#define L3C_PERF_CTRL_EN 0x10000#define L3C_EVTYPE_NONE 0xff/*
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 162/172 selftests/net: in timestamping, strncpy needs to preserve null byte
In reply to Sasha LevinFrom: tannerlove <[email protected]>
[ Upstream commit 8027bc0307ce59759b90679fa5d8b22949586d20 ]
If user passed an interface option longer than 15 characters, then device.ifr_name and hwtstamp.ifr_name became non-null-terminated strings. The compiler warned about this:
timestamping.c:353:2: warning: ‘strncpy’ specified bound 16 equals \
destination size [-Wstringop-truncation]
353 | strncpy(device.ifr_name, interface, sizeof(device.ifr_name));
--- .../selftests/networking/timestamping/timestamping.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-)
tools/testing/selftests/networking/timestamping/timestamping.c +8 -2
@@ -332,10 +332,16 @@ int main(int argc, char **argv)int val;socklen_t len;struct timeval next; +size_t if_len;if (argc <2 )usage (0 ); interface = argv[1 ]; + if_len =strlen (interface); +if (if_len >=IFNAMSIZ ) { +printf ("interface name exceeds IFNAMSIZ\n" ); +exit (1 ); + }for (i =2 ; i < argc; i++) {if (!strcasecmp (argv[i],"SO_TIMESTAMP" ))
@@ -369,12 +375,12 @@ int main(int argc, char **argv)bail ("socket" );memset (&device,0 ,sizeof (device)); -strncpy (device.ifr_name, interface,sizeof (device.ifr_name)); +memcpy (device.ifr_name, interface, if_len +1 );if (ioctl (sock,SIOCGIFADDR , &device) <0 )bail ("getting interface IP address" );memset (&hwtstamp,0 ,sizeof (hwtstamp)); -strncpy (hwtstamp.ifr_name, interface,sizeof (hwtstamp.ifr_name)); +memcpy (hwtstamp.ifr_name, interface, if_len +1 ); hwtstamp.ifr_data = (void *)&hwconfig;memset (&hwconfig,0 ,sizeof (hwconfig)); hwconfig.tx_type =
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 163/172 afs: Fix memory leak in afs_put_sysnames()
In reply to Sasha LevinFrom: Zhihao Cheng <[email protected]>
[ Upstream commit 2ca068be09bf8e285036603823696140026dcbe7 ]
Fix afs_put_sysnames() to actually free the specified afs_sysnames object after its reference count has been decreased to zero and its contents have been released.
--- fs/afs/proc.c | 1 + 1 file changed, 1 insertion(+)
fs/afs/proc.c +1 -0
@@ -512,6 +512,7 @@ void afs_put_sysnames(struct afs_sysnames *sysnames)if (sysnames->subs[i] != afs_init_sysname && sysnames->subs[i] != sysnames->blank)kfree (sysnames->subs[i]); +kfree (sysnames); } }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 164/172 ASoC: core: only convert non DPCM link to DPCM link
In reply to Sasha LevinFrom: Bard Liao <[email protected]>
[ Upstream commit 607fa205a7e4dfad28b8a67ab1c985756ddbccb0 ]
Additional checks for valid DAIs expose a corner case, where existing BE dailinks get modified, e.g. HDMI links are tagged with dpcm_capture=1 even if the DAIs are for playback.
This patch makes those changes conditional and flags configuration issues when a BE dailink is has no_pcm=0 but dpcm_playback or dpcm_capture=1 (which makes no sense).
As discussed on the alsa-devel mailing list, there are redundant flags for dpcm_playback, dpcm_capture, playback_only, capture_only. This will have to be cleaned-up in a future update. For now only correct and flag problematic configurations.
--- sound/soc/soc-core.c | 22 +++++++++++++++++++--- 1 file changed, 19 insertions(+), 3 deletions(-)
sound/soc/soc-core.c +19 -3
@@ -1920,9 +1920,25 @@ static void soc_check_tplg_fes(struct snd_soc_card *card) dai_link->platform_name = component->name;/* convert non BE into BE */ - dai_link->no_pcm =1 ; - dai_link->dpcm_playback =1 ; - dai_link->dpcm_capture =1 ; +if (!dai_link->no_pcm) { + dai_link->no_pcm =1 ; + +if (dai_link->dpcm_playback) +dev_warn (card->dev, +"invalid configuration, dailink %s has flags no_pcm=0 and dpcm_playback=1\n" , + dai_link->name); +if (dai_link->dpcm_capture) +dev_warn (card->dev, +"invalid configuration, dailink %s has flags no_pcm=0 and dpcm_capture=1\n" , + dai_link->name); + +/* convert normal link into DPCM one */ +if (!(dai_link->dpcm_playback || + dai_link->dpcm_capture)) { + dai_link->dpcm_playback = !dai_link->capture_only; + dai_link->dpcm_capture = !dai_link->playback_only; + } + }/* override any BE fixups */ dai_link->be_hw_params_fixup =
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 165/172 ASoC: Intel: bytcr_rt5640: Add quirk for Toshiba Encore WT10-A tablet
In reply to Sasha LevinFrom: Hans de Goede <[email protected]>
[ Upstream commit 199a5e8fda54ab3c8c6f6bf980c004e97ebf5ccb ]
The Toshiba Encore WT10-A tablet almost fully works with the default settings for Bay Trail CR devices. The only issue is that it uses a digital mic. connected the the DMIC1 input instead of an analog mic.
Add a quirk for this model using the default settings with the input-map replaced with BYT_RT5640_DMIC1_MAP.
--- sound/soc/intel/boards/bytcr_rt5640.c | 12 ++++++++++++ 1 file changed, 12 insertions(+)
sound/soc/intel/boards/bytcr_rt5640.c +12 -0
@@ -724,6 +724,18 @@ static const struct dmi_system_id byt_rt5640_quirk_table[] = {BYT_RT5640_JD_NOT_INV | BYT_RT5640_MCLK_EN), }, + { /* Toshiba Encore WT10-A */ + .matches = { +DMI_EXACT_MATCH (DMI_SYS_VENDOR ,"TOSHIBA" ), + DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "TOSHIBA WT10-A-103"), + }, + .driver_data = (void *)(BYT_RT5640_DMIC1_MAP | +BYT_RT5640_JD_SRC_JD1_IN4P | +BYT_RT5640_OVCD_TH_2000UA | +BYT_RT5640_OVCD_SF_0P75 | +BYT_RT5640_SSP0_AIF2 | + BYT_RT5640_MCLK_EN), + }, { /* Catch-all for generic Insyde tablets, must be last */ .matches = { DMI_MATCH(DMI_SYS_VENDOR, "Insyde"),
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 166/172 ASoC: rt5645: Add platform-data for Asus T101HA
In reply to Sasha LevinFrom: Hans de Goede <[email protected]>
[ Upstream commit 79d4f823a06796656289f97b922493da5690e46c ]
The Asus T101HA uses the default jack-detect mode 3, but instead of using an analog microphone it is using a DMIC on dmic-data-pin 1, like the Asus T100HA. Note unlike the T100HA its jack-detect is not inverted.
Add a DMI quirk with the correct settings for this model.
--- sound/soc/codecs/rt5645.c | 14 ++++++++++++++ 1 file changed, 14 insertions(+)
sound/soc/codecs/rt5645.c +14 -0
@@ -3656,6 +3656,12 @@ static const struct rt5645_platform_data asus_t100ha_platform_data = { .inv_jd1_1 = true, }; +static const struct rt5645_platform_data asus_t101ha_platform_data = { + .dmic1_data_pin =RT5645_DMIC_DATA_IN2N , + .dmic2_data_pin =RT5645_DMIC2_DISABLE , + .jd_mode =3 , +}; +static const struct rt5645_platform_data lenovo_ideapad_miix_310_pdata = { .jd_mode =3 , .in2_diff = true,
@@ -3733,6 +3739,14 @@ static const struct dmi_system_id dmi_platform_data[] = { }, .driver_data = (void *)&asus_t100ha_platform_data, }, + { + .ident = "ASUS T101HA", + .matches = { +DMI_MATCH (DMI_SYS_VENDOR ,"ASUSTeK COMPUTER INC." ), + DMI_MATCH(DMI_PRODUCT_NAME, "T101HA"), + }, + .driver_data = (void *)&asus_t101ha_platform_data, + }, { .ident ="MINIX Z83-4" , .matches = {
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 167/172 selftests/net: in rxtimestamp getopt_long needs terminating null entry
In reply to Sasha LevinFrom: tannerlove <[email protected]>
[ Upstream commit 865a6cbb2288f8af7f9dc3b153c61b7014fdcf1e ]
getopt_long requires the last element to be filled with zeros. Otherwise, passing an unrecognized option can cause a segfault.
--- tools/testing/selftests/networking/timestamping/rxtimestamp.c | 1 + 1 file changed, 1 insertion(+)
tools/testing/selftests/networking/timestamping/rxtimestamp.c +1 -0
@@ -114,6 +114,7 @@ static struct option long_options[] = { { "tcp", no_argument, 0, 't' }, { "udp", no_argument, 0, 'u' }, { "ip", no_argument, 0, 'i' }, + { NULL, 0, NULL, 0 }, };static int next_port =19999 ;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 168/172 drm/sun4i: hdmi ddc clk: Fix size of m divider
In reply to Sasha LevinFrom: Jernej Skrabec <[email protected]>
[ Upstream commit 54e1e06bcf1cf6e7ac3f86daa5f7454add24b494 ]
m divider in DDC clock register is 4 bits wide. Fix that.
--- drivers/gpu/drm/sun4i/sun4i_hdmi.h | 2 +- drivers/gpu/drm/sun4i/sun4i_hdmi_ddc_clk.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
drivers/gpu/drm/sun4i/sun4i_hdmi.h +1 -1
@@ -152,7 +152,7 @@#define SUN4I_HDMI_DDC_CMD_IMPLICIT_WRITE 3#define SUN4I_HDMI_DDC_CLK_REG 0x528 -#define SUN4I_HDMI_DDC_CLK_M (m) (((m) & 0x7) << 3) +#define SUN4I_HDMI_DDC_CLK_M (m) (((m) & 0xf) << 3)#define SUN4I_HDMI_DDC_CLK_N (n) ((n) & 0x7)#define SUN4I_HDMI_DDC_LINE_CTRL_REG 0x540
drivers/gpu/drm/sun4i/sun4i_hdmi_ddc_clk.c +1 -1
@@ -37,7 +37,7 @@ static unsigned long sun4i_ddc_calc_divider(unsigned long rate,unsigned long best_rate =0 ;u8 best_m =0 , best_n =0 , _m, _n; -for (_m =0 ; _m <8 ; _m++) { +for (_m =0 ; _m <16 ; _m++) {for (_n =0 ; _n <8 ; _n++) {unsigned long tmp_rate;
Signature · 6 lines
2.25.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sasha Levin
maintainerPATCH 169/172 scsi: acornscsi: Fix an error handling path in acornscsi_probe()
In reply to Sasha LevinFrom: Christophe JAILLET <[email protected]>
[ Upstream commit 42c76c9848e13dbe0538d7ae0147a269dfa859cb ]
'ret' is known to be 0 at this point. Explicitly return -ENOMEM if one of the 'ecardm_iomap()' calls fail.
--- drivers/scsi/arm/acornscsi.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/scsi/arm/acornscsi.c +3 -1
@@ -2914,8 +2914,10 @@ static int acornscsi_probe(struct expansion_card *ec, const struct ecard_id *id) ashost->base =ecardm_iomap (ec,ECARD_RES_MEMC ,0 ,0 ); ashost->fast =ecardm_iomap (ec,ECARD_RES_IOCFAST ,0 ,0 ); -if (!ashost->base || !ashost->fast) +if (!ashost->base || !ashost->fast) { + ret = -ENOMEM ; goto out_put; + } host->irq = ec->irq; ashost->host = host;
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 170/172 x86/idt: Keep spurious entries unset in system_vectors
In reply to Sasha LevinFrom: Vitaly Kuznetsov <[email protected]>
[ Upstream commit 1f1fbc70c10e81f70e9fbe2102d439c883269811 ]
With commit dc20b2d52653 ("x86/idt: Move interrupt gate initialization to IDT code") non assigned system vectors are also marked as used in 'used_vectors' (now 'system_vectors') bitmap. This makes checks in arch_show_interrupts() whether a particular system vector is allocated to always pass and e.g. 'Hyper-V reenlightenment interrupts' entry always shows up in /proc/interrupts.
Another side effect of having all unassigned system vectors marked as used is that irq_matrix_debug_show() will wrongly count them among 'System' vectors.
As it is now ensured that alloc_intr_gate() is not called after init, it is possible to leave unused entries in 'system_vectors' unset to fix these issues.
--- arch/x86/kernel/idt.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
arch/x86/kernel/idt.c +5 -1
@@ -320,7 +320,11 @@ void __init idt_setup_apic_and_irq_gates(void)#ifdef CONFIG_X86_LOCAL_APIC for_each_clear_bit_from (i, system_vectors,NR_VECTORS ) { -set_bit (i, system_vectors); +/* +* Don't set the non assigned system vectors in the +* system_vectors bitmap. Otherwise they show up in +* /proc/interrupts. +*/ entry = spurious_entries_start +8 * (i -FIRST_SYSTEM_VECTOR );set_intr_gate (i, entry); }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 171/172 net/filter: Permit reading NET in load_bytes_relative when MAC not set
In reply to Sasha LevinFrom: YiFei Zhu <[email protected]>
[ Upstream commit 0f5d82f187e1beda3fe7295dfc500af266a5bd80 ]
Added a check in the switch case on start_header that checks for the existence of the header, and in the case that MAC is not set and the caller requests for MAC, -EFAULT. If the caller requests for NET then MAC's existence is completely ignored.
There is no function to check NET header's existence and as far as cgroup_skb/egress is concerned it should always be set.
Removed for ptr >= the start of header, considering offset is bounded unsigned and should always be true. len <= end - mac is redundant to ptr + len <= end.
--- net/core/filter.c | 16 +++++++++------- 1 file changed, 9 insertions(+), 7 deletions(-)
net/core/filter.c +9 -7
@@ -1730,25 +1730,27 @@ BPF_CALL_5(bpf_skb_load_bytes_relative, const struct sk_buff *, skb, u32, offset, void *, to, u32, len, u32, start_header) {u8 *end =skb_tail_pointer (skb); -u8 *net =skb_network_header (skb); -u8 *mac =skb_mac_header (skb); -u8 *ptr; +u8 *start, *ptr; -if (unlikely (offset >0xffff || len > (end - mac))) +if (unlikely (offset >0xffff )) goto err_clear;switch (start_header) {case BPF_HDR_START_MAC : - ptr = mac + offset; +if (unlikely (!skb_mac_header_was_set (skb))) + goto err_clear; + start =skb_mac_header (skb);break ;case BPF_HDR_START_NET : - ptr = net + offset; + start =skb_network_header (skb);break ;default : goto err_clear; } -if (likely (ptr >= mac && ptr + len <= end)) { + ptr = start + offset; + +if (likely (ptr + len <= end)) {memcpy (to, ptr, len);return 0 ; }
Signature · 1 line
2.25.1
Sasha Levin
maintainerPATCH 172/172 xdp: Fix xsk_generic_xmit errno
In reply to Sasha LevinFrom: Li RongQing <[email protected]>
[ Upstream commit aa2cad0600ed2ca6a0ab39948d4db1666b6c962b ]
Propagate sock_alloc_send_skb error code, not set it to EAGAIN unconditionally, when fail to allocate skb, which might cause that user space unnecessary loops.
--- net/xdp/xsk.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-)
net/xdp/xsk.c +1 -3
@@ -233,10 +233,8 @@ static int xsk_generic_xmit(struct sock *sk, struct msghdr *m, len = desc.len; skb =sock_alloc_send_skb (sk, len,1 , &err); -if (unlikely (!skb)) { - err = -EAGAIN ; +if (unlikely (!skb)) goto out; - }skb_put (skb, len); addr = desc.addr;
Signature · 1 line
2.25.1