Skip to contentSkip to conversation

pinctrl: meson: fix drive strength register and bit calculation

PATCH Applied Hyeonki Hong 3 participants 3 messages Jun 18, 2020 – Aug 17, 2020

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 pinctrl: meson: fix drive strength register and bit calculation

If a GPIO bank has greater than 16 pins, PAD_DS_REG is split into two or more registers. However, when register and bit were calculated, the first register defined in the bank was used, and the bit was calculated based on the first pin. This causes problems in setting the driving strength.

The following method was used to solve this problem:
A bit is calculated first using predefined strides. Then, If the bit is 32 or more, the register is changed by the quotient of the bit divided by 32. And the bit is set to the remainder.

---
 drivers/pinctrl/meson/pinctrl-meson.c | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)
drivers/pinctrl/meson/pinctrl-meson.c +7 -4
index bbc919bef2bf..bf116c2e45c0 100644
@@ -56,6 +56,10 @@
 #include "../pinctrl-utils.h"
 #include "pinctrl-meson.h"
 
+static const unsigned int meson_bit_strides[] = {
+	1, 1, 1, 1, 1, 2, 1
+};
+
 /**
  * meson_get_bank() - find the bank containing a given pin
  *
@@ -96,8 +100,9 @@ static void meson_calc_reg_and_bit(struct meson_bank *bank, unsigned int pin,
 {
 	struct meson_reg_desc *desc = &bank->regs[reg_type];
 
-	*reg = desc->reg * 4;
-	*bit = desc->bit + pin - bank->first;
+	*bit = (desc->bit + pin - bank->first) * meson_bit_strides[reg_type];
+	*reg = (desc->reg + (*bit / 32)) * 4;
+	*bit &= 0x1f;
 }
 
 static int meson_get_groups_count(struct pinctrl_dev *pcdev)
@@ -314,7 +319,6 @@ static int meson_pinconf_set_drive_strength(struct meson_pinctrl *pc,
 		return ret;
 
 	meson_calc_reg_and_bit(bank, pin, REG_DS, &reg, &bit);
-	bit = bit << 1;
 
 	if (drive_strength_ua <= 500) {
 		ds_val = MESON_PINCONF_DRV_500UA;
@@ -441,7 +445,6 @@ static int meson_pinconf_get_drive_strength(struct meson_pinctrl *pc,
 		return ret;
 
 	meson_calc_reg_and_bit(bank, pin, REG_DS, &reg, &bit);
-	bit = bit << 1;
 
 	ret = regmap_read(pc->reg_ds, reg, &val);
 	if (ret)
Signature · 1 line
2.17.1
#1 lore raw
Quoted 6 lines · Hyeonki Hong

If a GPIO bank has greater than 16 pins, PAD_DS_REG is split into two or more registers. However, when register and bit were calculated, the first register defined in the bank was used, and the bit was calculated based on the first pin. This causes problems in setting the driving strength.

Quoted 6 lines

The following method was used to solve this problem:
A bit is calculated first using predefined strides. Then, If the bit is 32 or more, the register is changed by the quotient of the bit divided by 32. And the bit is set to the remainder.

Patch applied.

Yours,
Linus Walleij

#2 lore raw
In reply to Hyeonki Hong
This patch was applied to khilman/linux-amlogic.git (refs/heads/for-next).

Hello:

This patch was applied to khilman/linux-amlogic.git (refs/heads/for-next).

Quoted 6 lines · On Thu, 18 Jun 2020 11:59:22 +0900 you wrote:

If a GPIO bank has greater than 16 pins, PAD_DS_REG is split into two or more registers. However, when register and bit were calculated, the first register defined in the bank was used, and the bit was calculated based on the first pin. This causes problems in setting the driving strength.

Quoted 6 lines

The following method was used to solve this problem:
A bit is calculated first using predefined strides. Then, If the bit is 32 or more, the register is changed by the quotient of the bit divided by 32. And the bit is set to the remainder.

[...]

Here is a summary with links:
- [v2] pinctrl: meson: fix drive strength register and bit calculation

    https://git.kernel.org/khilman/linux-amlogic/c/f088ab6d4f4ce49d422c220074b7e605f54e2299

You are awesome, thank you!

Signature · 7 lines
Deet-doot-dot, I am a bot.
https://korg.wiki.kernel.org/userdoc/pwbot

_______________________________________________
linux-amlogic mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-amlogic