v2: rr3188: change APP to 600MHz and enable bwadj for DPLL
Subsystems (2)
cover v2: rr3188: change APP to 600MHz and enable bwadj for DPLL
Hello!
Here are two patches I found usefull for rk3188.
Changes in v2:
Add u-boot at lists.denx.de as addressee.
Alexander Kochetkov (2):
rockchip: clk: rk3188: change APLL to safe 600MHz
rockchip: clk: rk3188: enable bwadj for rk3188 DPLL
drivers/clk/rockchip/clk_rk3188.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-)
Signature · 1 line
2.17.1
PATCH 1/2 rockchip: clk: rk3188: change APLL to safe 600MHz
The commit 84a6a27ae3ff ("rockchip: rk3188: init CPU freq in clock driver") changed ARM clock from 600MHz to 1600MHz. It made boot unstable due to the fact that PMIC at the start generates insufficient voltage for operation. See also: commit f4f57c58b589 ("rockchip:
rk3188: Setup the armclk in spl").
Fixes commit 84a6a27ae3ff ("rockchip: rk3188: init CPU freq in clock driver").
--- drivers/clk/rockchip/clk_rk3188.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/clk/rockchip/clk_rk3188.c +2 -1
@@ -564,7 +564,8 @@ static int rk3188_clk_probe(struct udevice *dev)rkclk_init (priv->cru, priv->grf, priv->has_bwadj);/* Init CPU frequency */ -rkclk_configure_cpu (priv->cru, priv->grf,APLL_HZ , priv->has_bwadj); +rkclk_configure_cpu (priv->cru, priv->grf,APLL_SAFE_HZ , + priv->has_bwadj);#endif return 0 ;
Signature · 1 line
2.17.1
PATCH 1/2 rockchip: clk: rk3188: change APLL to safe 600MHz
Quoted 10 lines · Alexander Kochetkov
The commit
84a6a27ae3ff("rockchip: rk3188: init CPU freq in clock driver") changed ARM clock from 600MHz to 1600MHz. It made boot unstable due to the fact that PMIC at the start generates insufficient voltage for operation. See also: commitf4f57c58b589("rockchip:
rk3188: Setup the armclk in spl").Fixes commit
84a6a27ae3ff("rockchip: rk3188: init CPU freq in clock driver").Signed-off-by Alexander Kochetkov <[email protected]>
Thanks,
- Kever
Quoted 18 lines
--- drivers/clk/rockchip/clk_rk3188.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/clk/rockchip/clk_rk3188.c +2
-1@@ -564,7 +564,8 @@ static int rk3188_clk_probe(struct udevice *dev)rkclk_init (priv->cru, priv->grf, priv->has_bwadj);/* Init CPU frequency */ -rkclk_configure_cpu (priv->cru, priv->grf,APLL_HZ , priv->has_bwadj); +rkclk_configure_cpu (priv->cru, priv->grf,APLL_SAFE_HZ , + priv->has_bwadj);#endif return 0 ;
PATCH 2/2 rockchip: clk: rk3188: enable bwadj for rk3188 DPLL
In reply to Alexander KochetkovEmpirically, I found that DPLL on rk3188 has bwadj registers. Configuring DPLL with bwadj increase DPLL stability. Because of DPLL provide clock for ethernet, enabling bwaj reduces the number of errors on the ethernet.
--- drivers/clk/rockchip/clk_rk3188.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/clk/rockchip/clk_rk3188.c +4 -4
@@ -117,7 +117,7 @@ static int rkclk_set_pll(struct rk3188_cru *cru, enum rk_clk_id clk_id, }static int rkclk_configure_ddr (struct rk3188_cru *cru,struct rk3188_grf *grf, -unsigned int hz,bool has_bwadj) +unsigned int hz) {static const struct pll_div dpll_cfg[] = { {.nf =75 , .nr =1 , .no =6 },
@@ -149,7 +149,8 @@ static int rkclk_configure_ddr(struct rk3188_cru *cru, struct rk3188_grf *grf,rk_clrsetreg (&cru->cru_mode_con,DPLL_MODE_MASK <<DPLL_MODE_SHIFT ,DPLL_MODE_SLOW <<DPLL_MODE_SHIFT ); -rkclk_set_pll (cru,CLK_DDR , &dpll_cfg[cfg], has_bwadj); +/* rk3188 and rk3188a DPLL has bwadj */ +rkclk_set_pll (cru,CLK_DDR , &dpll_cfg[cfg],1 );/* wait for pll lock */ while (!(readl (&grf->soc_status0) &SOCSTS_DPLL_LOCK ))
@@ -504,8 +505,7 @@ static ulong rk3188_clk_set_rate(struct clk *clk, ulong rate) priv->has_bwadj);break ;case CLK_DDR : - new_rate =rkclk_configure_ddr (priv->cru, priv->grf, rate, - priv->has_bwadj); + new_rate =rkclk_configure_ddr (priv->cru, priv->grf, rate);break ;case HCLK_EMMC :case HCLK_SDMMC :
Signature · 1 line
2.17.1
PATCH 2/2 rockchip: clk: rk3188: enable bwadj for rk3188 DPLL
Hi Alex,
??? I think it will be better to update the rk3188_clk_probe() function
instead of
what you have modified if the RK3188 and RK3188A has the same PLL(I'm not sure
about it now).
Thanks,
- Kever
Quoted 43 lines · Alexander Kochetkov
Empirically, I found that DPLL on rk3188 has bwadj registers. Configuring DPLL with bwadj increase DPLL stability. Because of DPLL provide clock for ethernet, enabling bwaj reduces the number of errors on the ethernet.
Signed-off-by Alexander Kochetkov <[email protected]>--- drivers/clk/rockchip/clk_rk3188.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)drivers/clk/rockchip/clk_rk3188.c +4
-4@@ -117,7 +117,7 @@ static int rkclk_set_pll(struct rk3188_cru *cru, enum rk_clk_id clk_id, }static int rkclk_configure_ddr (struct rk3188_cru *cru,struct rk3188_grf *grf, -unsigned int hz,bool has_bwadj) +unsigned int hz) {static const struct pll_div dpll_cfg[] = { {.nf =75 , .nr =1 , .no =6 },@@ -149,7 +149,8 @@ static int rkclk_configure_ddr(struct rk3188_cru *cru, struct rk3188_grf *grf,rk_clrsetreg (&cru->cru_mode_con,DPLL_MODE_MASK <<DPLL_MODE_SHIFT ,DPLL_MODE_SLOW <<DPLL_MODE_SHIFT ); -rkclk_set_pll (cru,CLK_DDR , &dpll_cfg[cfg], has_bwadj); +/* rk3188 and rk3188a DPLL has bwadj */ +rkclk_set_pll (cru,CLK_DDR , &dpll_cfg[cfg],1 );/* wait for pll lock */ while (!(readl (&grf->soc_status0) &SOCSTS_DPLL_LOCK ))@@ -504,8 +505,7 @@ static ulong rk3188_clk_set_rate(struct clk *clk, ulong rate) priv->has_bwadj);break ;case CLK_DDR : - new_rate =rkclk_configure_ddr (priv->cru, priv->grf, rate, - priv->has_bwadj); + new_rate =rkclk_configure_ddr (priv->cru, priv->grf, rate);break ;case HCLK_EMMC :case HCLK_SDMMC :
PATCH 2/2 rockchip: clk: rk3188: enable bwadj for rk3188 DPLL
Hi Kever,
Strange? Then I tested a year ago I saw, that writing into bwadj registers had no effect for some PLLs. But now I did another test. See patch and output. Looks like rk3188 allow writing into bwadj fields.
So I do something like 'priv->has_bwadj = 1' in the rk3188_clk_probe() and send try 2.
--------------------------------------
drivers/clk/rockchip/clk_rk3188.c +9 -3
@@ -91,7 +91,7 @@ static int rkclk_set_pll(struct rk3188_cru *cru, enum rk_clk_id clk_id,uint vco_hz =OSC_HZ /1000 * div->nf / div->nr *1000 ;uint output_hz = vco_hz / div->no; -debug ("PLL at %x: nf=%d, nr=%d, no=%d, vco=%u Hz, output=%u Hz\n" , +printf ("PLL at %x: nf=%d, nr=%d, no=%d, vco=%u Hz, output=%u Hz\n" , (uint )pll, div->nf, div->nr, div->no, vco_hz, output_hz); assert(vco_hz >= VCO_MIN_HZ && vco_hz <= VCO_MAX_HZ && output_hz >= OUTPUT_MIN_HZ && output_hz <= OUTPUT_MAX_HZ &&
@@ -105,8 +105,12 @@ static int rkclk_set_pll(struct rk3188_cru *cru, enum rk_clk_id clk_id, ((div->nr - 1) << CLKR_SHIFT) | (div->no - 1));rk_clrsetreg (&pll->con1,CLKF_MASK , div->nf -1 ); -if (has_bwadj) +if (has_bwadj) { +printf ("before: %p: con2=%x, clr=%x, set=%x\n" , + &pll->con2,readl (&pll->con2),PLL_BWADJ_MASK , (div->nf >>1 ) -1 );rk_clrsetreg (&pll->con2,PLL_BWADJ_MASK , (div->nf >>1 ) -1 ); +printf ("after: %p: con2=%x\n" , &pll->con2,readl (&pll->con2)); + }udelay (10 );
@@ -552,7 +556,9 @@ static int rk3188_clk_probe(struct udevice *dev) priv->grf =syscon_get_first_range (ROCKCHIP_SYSCON_GRF );if (IS_ERR (priv->grf))return PTR_ERR (priv->grf); - priv->has_bwadj = (type ==RK3188A_CRU ) ?1 :0 ; +printf ("type %d\n" , type); +//priv->has_bwadj = (type == RK3188A_CRU) ? 1 : 0; + priv->has_bwadj =1 ; ?????????????????????
type 0
PLL at 20000030: nf=64, nr=1, no=2, vco=1536000000 Hz, output=768000000 Hz
before: 20000038: con2=94, clr=fff, set=1f
after: 20000038: con2=1f
PLL at 20000020: nf=32, nr=1, no=2, vco=768000000 Hz, output=384000000 Hz
before: 20000028: con2=63, clr=fff, set=f
after: 20000028: con2=f
PLL at 20000000: nf=50, nr=1, no=2, vco=1200000000 Hz, output=600000000 Hz
before: 20000008: con2=18, clr=fff, set=18
after: 20000008: con2=18
PLL at 20000010: nf=75, nr=1, no=4, vco=1800000000 Hz, output=450000000 Hz
before: 20000018: con2=10b, clr=fff, set=24
after: 20000018: con2=24
Quoted 58 lines
27 ???? 2020 ?., ? 18:17, Kever Yang <[email protected]> ???????(?):
Hi Alex,
I think it will be better to update the
rk3188_clk_probe()function instead ofwhat you have modified if the RK3188 and RK3188A has the same PLL(I'm not sure
about it now).
Thanks,
- Kever
Quoted 40 lines · Alexander Kochetkov
Empirically, I found that DPLL on rk3188 has bwadj registers. Configuring DPLL with bwadj increase DPLL stability. Because of DPLL provide clock for ethernet, enabling bwaj reduces the number of errors on the ethernet.
Signed-off-by Alexander Kochetkov <[email protected]>--- drivers/clk/rockchip/clk_rk3188.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)drivers/clk/rockchip/clk_rk3188.c +4
-3@@ -117,7 +117,7 @@ static int rkclk_set_pll(struct rk3188_cru *cru, enum rk_clk_id clk_id, }static int rkclk_configure_ddr (struct rk3188_cru *cru,struct rk3188_grf *grf, -unsigned int hz,bool has_bwadj) +unsigned int hz) {static const struct pll_div dpll_cfg[] = { {.nf =75 , .nr =1 , .no =6 },@@ -149,7 +149,8 @@ static int rkclk_configure_ddr(struct rk3188_cru *cru, struct rk3188_grf *grf,rk_clrsetreg (&cru->cru_mode_con,DPLL_MODE_MASK <<DPLL_MODE_SHIFT ,DPLL_MODE_SLOW <<DPLL_MODE_SHIFT ); -rkclk_set_pll (cru,CLK_DDR , &dpll_cfg[cfg], has_bwadj); +/* rk3188 and rk3188a DPLL has bwadj */ +rkclk_set_pll (cru,CLK_DDR , &dpll_cfg[cfg],1 );/* wait for pll lock */ while (!(readl (&grf->soc_status0) &SOCSTS_DPLL_LOCK ))@@ -504,8 +505,7 @@ static ulong rk3188_clk_set_rate(struct clk *clk, ulong rate) priv->has_bwadj);break ;case CLK_DDR : - new_rate =rkclk_configure_ddr (priv->cru, priv->grf, rate, - priv->has_bwadj); + new_rate =rkclk_configure_ddr (priv->cru, priv->grf, rate);break ;case HCLK_EMMC :case HCLK_SDMMC :