Skip to contentSkip to conversation

dt-bindings: pci: tegra: Remove PLL power supplies

PATCH Applied Thierry Reding 3 participants 12 messages Jun 23, 2020 – Jul 28, 2020

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/2 dt-bindings: pci: tegra: Remove PLL power supplies

From: Thierry Reding <[email protected]>

The XUSB pad controller, which provides access to various USB, PCI and SATA pads (or PHYs), needs to bring up the PLLs associated with these pads. In order to properly do so, it needs to control the power supplied to these PLLs.

Remove the PLL power supplies from the PCIe controller because it does not need direct access to them. Instead it will only use the configured pads provided by the XUSB pad controller.

---
Hi Rob,

I already made this change as part of the conversion series, but wanted to send this out as part of this subseries since it addresses a fairly long-standing issue that I'd like to clean up irrespective of the DT binding conversion. Since it looks like the conversion series will take a bit longer, I think it makes sense to send this out separately.

Thierry

 .../devicetree/bindings/pci/nvidia,tegra20-pcie.txt  | 12 ------------
 1 file changed, 12 deletions(-)
Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +0 -12
index 7939bca47861..d099f3476ccc 100644
@@ -112,28 +112,16 @@ Power supplies for Tegra124:
 - Required:
   - avddio-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V.
   - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
-  - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must
-    supply 1.05 V.
   - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks.
     Must supply 3.3 V.
-  - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3).
-    Must supply 3.3 V.
   - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must
     supply 2.8-3.3 V.
-  - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must
-    supply 1.05 V.
 
 Power supplies for Tegra210:
 - Required:
-  - avdd-pll-uerefe-supply: Power supply for PLLE (shared with USB3). Must
-    supply 1.05 V.
   - hvddio-pex-supply: High-voltage supply for PCIe I/O and PCIe output
     clocks. Must supply 1.8 V.
   - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
-  - dvdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must
-    supply 1.05 V.
-  - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3).
-    Must supply 3.3 V.
   - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must
     supply 1.8 V.
 
Signature · 1 line
2.27.0
#1 lore raw

PATCH v2 2/2 PCI: tegra: Remove PLL power supplies

From: Thierry Reding <[email protected]>

The Tegra PCI controller driver doesn't need to control the PLL power supplies directly, but rather uses the pads provided by the XUSB pad controller, which in turn is responsible for supplying power to the PLLs.

---
 drivers/pci/controller/pci-tegra.c | 10 ++--------
 1 file changed, 2 insertions(+), 8 deletions(-)
drivers/pci/controller/pci-tegra.c +2 -8
index 235b456698fc..f87a09d21eb0 100644
@@ -2025,7 +2025,7 @@ static int tegra_pcie_get_regulators(struct tegra_pcie *pcie, u32 lane_mask)
 		pcie->supplies[i++].supply = "hvdd-pex";
 		pcie->supplies[i++].supply = "vddio-pexctl-aud";
 	} else if (of_device_is_compatible(np, "nvidia,tegra210-pcie")) {
-		pcie->num_supplies = 6;
+		pcie->num_supplies = 3;
 
 		pcie->supplies = devm_kcalloc(pcie->dev, pcie->num_supplies,
 					      sizeof(*pcie->supplies),
@@ -2033,14 +2033,11 @@ static int tegra_pcie_get_regulators(struct tegra_pcie *pcie, u32 lane_mask)
 		if (!pcie->supplies)
 			return -ENOMEM;
 
-		pcie->supplies[i++].supply = "avdd-pll-uerefe";
 		pcie->supplies[i++].supply = "hvddio-pex";
 		pcie->supplies[i++].supply = "dvddio-pex";
-		pcie->supplies[i++].supply = "dvdd-pex-pll";
-		pcie->supplies[i++].supply = "hvdd-pex-pll-e";
 		pcie->supplies[i++].supply = "vddio-pex-ctl";
 	} else if (of_device_is_compatible(np, "nvidia,tegra124-pcie")) {
-		pcie->num_supplies = 7;
+		pcie->num_supplies = 4;
 
 		pcie->supplies = devm_kcalloc(dev, pcie->num_supplies,
 					      sizeof(*pcie->supplies),
@@ -2050,11 +2047,8 @@ static int tegra_pcie_get_regulators(struct tegra_pcie *pcie, u32 lane_mask)
 
 		pcie->supplies[i++].supply = "avddio-pex";
 		pcie->supplies[i++].supply = "dvddio-pex";
-		pcie->supplies[i++].supply = "avdd-pex-pll";
 		pcie->supplies[i++].supply = "hvdd-pex";
-		pcie->supplies[i++].supply = "hvdd-pex-pll-e";
 		pcie->supplies[i++].supply = "vddio-pex-ctl";
-		pcie->supplies[i++].supply = "avdd-pll-erefe";
 	} else if (of_device_is_compatible(np, "nvidia,tegra30-pcie")) {
 		bool need_pexa = false, need_pexb = false;
 
Signature · 1 line
2.27.0
#2 lore raw

Re: [PATCH v2 2/2] PCI: tegra: Remove PLL power supplies

Quoted 11 lines · Thierry Reding

From: Thierry Reding <[email protected]>

The Tegra PCI controller driver doesn't need to control the PLL power supplies directly, but rather uses the pads provided by the XUSB pad controller, which in turn is responsible for supplying power to the PLLs.

---
 drivers/pci/controller/pci-tegra.c | 10 ++--------
 1 file changed, 2 insertions(+), 8 deletions(-)

Hi Lorenzo,

do you have any comments on this? Can we get this into v5.9?

Thanks,
Thierry

Quoted 44 lines
drivers/pci/controller/pci-tegra.c +2 -8
index 235b456698fc..f87a09d21eb0 100644
@@ -2025,7 +2025,7 @@ static int tegra_pcie_get_regulators(struct tegra_pcie *pcie, u32 lane_mask)
 		pcie->supplies[i++].supply = "hvdd-pex";
 		pcie->supplies[i++].supply = "vddio-pexctl-aud";
 	} else if (of_device_is_compatible(np, "nvidia,tegra210-pcie")) {
-		pcie->num_supplies = 6;
+		pcie->num_supplies = 3;
 
 		pcie->supplies = devm_kcalloc(pcie->dev, pcie->num_supplies,
 					      sizeof(*pcie->supplies),
@@ -2033,14 +2033,11 @@ static int tegra_pcie_get_regulators(struct tegra_pcie *pcie, u32 lane_mask)
 		if (!pcie->supplies)
 			return -ENOMEM;
 
-		pcie->supplies[i++].supply = "avdd-pll-uerefe";
 		pcie->supplies[i++].supply = "hvddio-pex";
 		pcie->supplies[i++].supply = "dvddio-pex";
-		pcie->supplies[i++].supply = "dvdd-pex-pll";
-		pcie->supplies[i++].supply = "hvdd-pex-pll-e";
 		pcie->supplies[i++].supply = "vddio-pex-ctl";
 	} else if (of_device_is_compatible(np, "nvidia,tegra124-pcie")) {
-		pcie->num_supplies = 7;
+		pcie->num_supplies = 4;
 
 		pcie->supplies = devm_kcalloc(dev, pcie->num_supplies,
 					      sizeof(*pcie->supplies),
@@ -2050,11 +2047,8 @@ static int tegra_pcie_get_regulators(struct tegra_pcie *pcie, u32 lane_mask)
 
 		pcie->supplies[i++].supply = "avddio-pex";
 		pcie->supplies[i++].supply = "dvddio-pex";
-		pcie->supplies[i++].supply = "avdd-pex-pll";
 		pcie->supplies[i++].supply = "hvdd-pex";
-		pcie->supplies[i++].supply = "hvdd-pex-pll-e";
 		pcie->supplies[i++].supply = "vddio-pex-ctl";
-		pcie->supplies[i++].supply = "avdd-pll-erefe";
 	} else if (of_device_is_compatible(np, "nvidia,tegra30-pcie")) {
 		bool need_pexa = false, need_pexb = false;
 
Signature · 1 line
2.27.0
#3 lore raw

Re: [PATCH v2 2/2] PCI: tegra: Remove PLL power supplies

Quoted 8 lines · Thierry Reding
Quoted 7 lines · Thierry Reding

From: Thierry Reding <[email protected]>

The Tegra PCI controller driver doesn't need to control the PLL power supplies directly, but rather uses the pads provided by the XUSB pad controller, which in turn is responsible for supplying power to the PLLs.

Quoted 8 lines
Quoted 4 lines
---
 drivers/pci/controller/pci-tegra.c | 10 ++--------
 1 file changed, 2 insertions(+), 8 deletions(-)

Hi Lorenzo,

do you have any comments on this? Can we get this into v5.9?

Yes we can if Rob is happy with patch (1).

Thanks,
Lorenzo

Quoted 47 lines

Thanks,
Thierry

Quoted 44 lines
drivers/pci/controller/pci-tegra.c +2 -8
index 235b456698fc..f87a09d21eb0 100644
@@ -2025,7 +2025,7 @@ static int tegra_pcie_get_regulators(struct tegra_pcie *pcie, u32 lane_mask)
 		pcie->supplies[i++].supply = "hvdd-pex";
 		pcie->supplies[i++].supply = "vddio-pexctl-aud";
 	} else if (of_device_is_compatible(np, "nvidia,tegra210-pcie")) {
-		pcie->num_supplies = 6;
+		pcie->num_supplies = 3;
 
 		pcie->supplies = devm_kcalloc(pcie->dev, pcie->num_supplies,
 					      sizeof(*pcie->supplies),
@@ -2033,14 +2033,11 @@ static int tegra_pcie_get_regulators(struct tegra_pcie *pcie, u32 lane_mask)
 		if (!pcie->supplies)
 			return -ENOMEM;
 
-		pcie->supplies[i++].supply = "avdd-pll-uerefe";
 		pcie->supplies[i++].supply = "hvddio-pex";
 		pcie->supplies[i++].supply = "dvddio-pex";
-		pcie->supplies[i++].supply = "dvdd-pex-pll";
-		pcie->supplies[i++].supply = "hvdd-pex-pll-e";
 		pcie->supplies[i++].supply = "vddio-pex-ctl";
 	} else if (of_device_is_compatible(np, "nvidia,tegra124-pcie")) {
-		pcie->num_supplies = 7;
+		pcie->num_supplies = 4;
 
 		pcie->supplies = devm_kcalloc(dev, pcie->num_supplies,
 					      sizeof(*pcie->supplies),
@@ -2050,11 +2047,8 @@ static int tegra_pcie_get_regulators(struct tegra_pcie *pcie, u32 lane_mask)
 
 		pcie->supplies[i++].supply = "avddio-pex";
 		pcie->supplies[i++].supply = "dvddio-pex";
-		pcie->supplies[i++].supply = "avdd-pex-pll";
 		pcie->supplies[i++].supply = "hvdd-pex";
-		pcie->supplies[i++].supply = "hvdd-pex-pll-e";
 		pcie->supplies[i++].supply = "vddio-pex-ctl";
-		pcie->supplies[i++].supply = "avdd-pll-erefe";
 	} else if (of_device_is_compatible(np, "nvidia,tegra30-pcie")) {
 		bool need_pexa = false, need_pexb = false;
 
Signature · 1 line
2.27.0
#4 lore raw

Re: [PATCH v2 2/2] PCI: tegra: Remove PLL power supplies

Quoted 14 lines · Lorenzo Pieralisi
Quoted 13 lines · Thierry Reding
Quoted 11 lines · Thierry Reding

From: Thierry Reding <[email protected]>

The Tegra PCI controller driver doesn't need to control the PLL power supplies directly, but rather uses the pads provided by the XUSB pad controller, which in turn is responsible for supplying power to the PLLs.

---
 drivers/pci/controller/pci-tegra.c | 10 ++--------
 1 file changed, 2 insertions(+), 8 deletions(-)
Quoted 5 lines
Quoted 3 lines

Hi Lorenzo,

do you have any comments on this? Can we get this into v5.9?

Yes we can if Rob is happy with patch (1).

I think this is mostly orthogonal to the bindings. We're already controlling these supplies from the UPHY driver and controlling them from the PCI driver is completely broken.

So I think technically these two patches could be applied separately, but it's fine if you want to wait for Rob's feedback.

Thierry

#5 lore raw

Re: [PATCH v2 2/2] PCI: tegra: Remove PLL power supplies

In reply to Thierry Reding
Quoted 8 lines · Thierry Reding

From: Thierry Reding <[email protected]>

The Tegra PCI controller driver doesn't need to control the PLL power supplies directly, but rather uses the pads provided by the XUSB pad controller, which in turn is responsible for supplying power to the PLLs.

Quoted 4 lines
---
 drivers/pci/controller/pci-tegra.c | 10 ++--------
 1 file changed, 2 insertions(+), 8 deletions(-)

What's going to happen here with a new dtb and an old kernel? Is it going to error out due to missing supplies?

Rob

#6 lore raw

Re: [PATCH v2 2/2] PCI: tegra: Remove PLL power supplies

Quoted 9 lines · Rob Herring
Quoted 8 lines · Thierry Reding

From: Thierry Reding <[email protected]>

The Tegra PCI controller driver doesn't need to control the PLL power supplies directly, but rather uses the pads provided by the XUSB pad controller, which in turn is responsible for supplying power to the PLLs.

Quoted 7 lines
Quoted 4 lines
---
 drivers/pci/controller/pci-tegra.c | 10 ++--------
 1 file changed, 2 insertions(+), 8 deletions(-)

What's going to happen here with a new dtb and an old kernel? Is it going to error out due to missing supplies?

It's not going to error out but fallback to the "dummy" regulator, so this should be fine from a forwards-compatibility point of view. Though I didn't think we technically cared about that direction very much.

Thierry

Reviewed-by
#7 lore raw

Re: [PATCH v2 2/2] PCI: tegra: Remove PLL power supplies

Quoted 16 lines · Thierry Reding
Quoted 14 lines · Rob Herring
Quoted 12 lines · Thierry Reding

From: Thierry Reding <[email protected]>

The Tegra PCI controller driver doesn't need to control the PLL power supplies directly, but rather uses the pads provided by the XUSB pad controller, which in turn is responsible for supplying power to the PLLs.

---
 drivers/pci/controller/pci-tegra.c | 10 ++--------
 1 file changed, 2 insertions(+), 8 deletions(-)
Quoted 6 lines
Quoted 2 lines

What's going to happen here with a new dtb and an old kernel? Is it going to error out due to missing supplies?

It's not going to error out but fallback to the "dummy" regulator, so this should be fine from a forwards-compatibility point of view. Though I didn't think we technically cared about that direction very much.

AIUI, SUSE ships newer DTs with stable kernels. Of course, the dtb's shouldn't really come from the OS vendors, but you wouldn't want a newer firmware (w/ dtb) to break your OS either.

In any case,

Rob

#8 lore raw
In reply to Thierry Reding
Quoted 21 lines · Thierry Reding

From: Thierry Reding <[email protected]>

The XUSB pad controller, which provides access to various USB, PCI and SATA pads (or PHYs), needs to bring up the PLLs associated with these pads. In order to properly do so, it needs to control the power supplied to these PLLs.

Remove the PLL power supplies from the PCIe controller because it does not need direct access to them. Instead it will only use the configured pads provided by the XUSB pad controller.

---
Hi Rob,

I already made this change as part of the conversion series, but wanted to send this out as part of this subseries since it addresses a fairly long-standing issue that I'd like to clean up irrespective of the DT binding conversion. Since it looks like the conversion series will take a bit longer, I think it makes sense to send this out separately.

Quoted 4 lines

Thierry

 .../devicetree/bindings/pci/nvidia,tegra20-pcie.txt  | 12 ------------
 1 file changed, 12 deletions(-)

Hi Rob, any feedback on this?

Thanks,
Thierry

Quoted 36 lines
Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +0 -12
index 7939bca47861..d099f3476ccc 100644
@@ -112,28 +112,16 @@ Power supplies for Tegra124:
 - Required:
   - avddio-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V.
   - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
-  - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must
-    supply 1.05 V.
   - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks.
     Must supply 3.3 V.
-  - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3).
-    Must supply 3.3 V.
   - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must
     supply 2.8-3.3 V.
-  - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must
-    supply 1.05 V.
 
 Power supplies for Tegra210:
 - Required:
-  - avdd-pll-uerefe-supply: Power supply for PLLE (shared with USB3). Must
-    supply 1.05 V.
   - hvddio-pex-supply: High-voltage supply for PCIe I/O and PCIe output
     clocks. Must supply 1.8 V.
   - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
-  - dvdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must
-    supply 1.05 V.
-  - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3).
-    Must supply 3.3 V.
   - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must
     supply 1.8 V.
 
Signature · 1 line
2.27.0
#9 lore raw
Quoted 22 lines · Thierry Reding
Quoted 21 lines · Thierry Reding

From: Thierry Reding <[email protected]>

The XUSB pad controller, which provides access to various USB, PCI and SATA pads (or PHYs), needs to bring up the PLLs associated with these pads. In order to properly do so, it needs to control the power supplied to these PLLs.

Remove the PLL power supplies from the PCIe controller because it does not need direct access to them. Instead it will only use the configured pads provided by the XUSB pad controller.

---
Hi Rob,

I already made this change as part of the conversion series, but wanted to send this out as part of this subseries since it addresses a fairly long-standing issue that I'd like to clean up irrespective of the DT binding conversion. Since it looks like the conversion series will take a bit longer, I think it makes sense to send this out separately.

Quoted 6 lines
Quoted 4 lines

Thierry

 .../devicetree/bindings/pci/nvidia,tegra20-pcie.txt  | 12 ------------
 1 file changed, 12 deletions(-)

Hi Rob, any feedback on this?

Hi Rob,

I'd like to queue both patches, please let me know if that's OK with you.

Thank you very much.

Lorenzo

Quoted 35 lines
Quoted 35 lines

index 7939bca47861..d099f3476ccc 100644

Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +0 -12
@@ -112,28 +112,16 @@ Power supplies for Tegra124:
 - Required:
   - avddio-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V.
   - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
-  - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must
-    supply 1.05 V.
   - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks.
     Must supply 3.3 V.
-  - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3).
-    Must supply 3.3 V.
   - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must
     supply 2.8-3.3 V.
-  - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must
-    supply 1.05 V.
 
 Power supplies for Tegra210:
 - Required:
-  - avdd-pll-uerefe-supply: Power supply for PLLE (shared with USB3). Must
-    supply 1.05 V.
   - hvddio-pex-supply: High-voltage supply for PCIe I/O and PCIe output
     clocks. Must supply 1.8 V.
   - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
-  - dvdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must
-    supply 1.05 V.
-  - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3).
-    Must supply 3.3 V.
   - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must
     supply 1.8 V.
 
Signature · 1 line
2.27.0
Reviewed-by on v2 1/2
#10 lore raw
In reply to Thierry Reding
Quoted 22 lines · Thierry Reding

From: Thierry Reding <[email protected]>

The XUSB pad controller, which provides access to various USB, PCI and SATA pads (or PHYs), needs to bring up the PLLs associated with these pads. In order to properly do so, it needs to control the power supplied to these PLLs.

Remove the PLL power supplies from the PCIe controller because it does not need direct access to them. Instead it will only use the configured pads provided by the XUSB pad controller.

---
Hi Rob,

I already made this change as part of the conversion series, but wanted to send this out as part of this subseries since it addresses a fairly long-standing issue that I'd like to clean up irrespective of the DT binding conversion. Since it looks like the conversion series will take a bit longer, I think it makes sense to send this out separately.

Quoted 4 lines

Thierry

 .../devicetree/bindings/pci/nvidia,tegra20-pcie.txt  | 12 ------------
 1 file changed, 12 deletions(-)
#11 lore raw
In reply to Thierry Reding
Quoted 12 lines · Thierry Reding

From: Thierry Reding <[email protected]>

The XUSB pad controller, which provides access to various USB, PCI and SATA pads (or PHYs), needs to bring up the PLLs associated with these pads. In order to properly do so, it needs to control the power supplied to these PLLs.

Remove the PLL power supplies from the PCIe controller because it does not need direct access to them. Instead it will only use the configured pads provided by the XUSB pad controller.

Quoted 8 lines

---
Hi Rob,

I already made this change as part of the conversion series, but wanted to send this out as part of this subseries since it addresses a fairly long-standing issue that I'd like to clean up irrespective of the DT binding conversion. Since it looks like the conversion series will take a bit longer, I think it makes sense to send this out separately.

Applied the series to pci/tegra, thanks.

Lorenzo

Quoted 41 lines

Thierry

 .../devicetree/bindings/pci/nvidia,tegra20-pcie.txt  | 12 ------------
 1 file changed, 12 deletions(-)
Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +0 -12
index 7939bca47861..d099f3476ccc 100644
@@ -112,28 +112,16 @@ Power supplies for Tegra124:
 - Required:
   - avddio-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V.
   - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
-  - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must
-    supply 1.05 V.
   - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks.
     Must supply 3.3 V.
-  - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3).
-    Must supply 3.3 V.
   - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must
     supply 2.8-3.3 V.
-  - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must
-    supply 1.05 V.
 
 Power supplies for Tegra210:
 - Required:
-  - avdd-pll-uerefe-supply: Power supply for PLLE (shared with USB3). Must
-    supply 1.05 V.
   - hvddio-pex-supply: High-voltage supply for PCIe I/O and PCIe output
     clocks. Must supply 1.8 V.
   - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
-  - dvdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must
-    supply 1.05 V.
-  - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3).
-    Must supply 3.3 V.
   - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must
     supply 1.8 V.
 
Signature · 1 line
2.27.0