Skip to contentSkip to conversation

drm/vmwgfx: Fix two list_for_each loop exit tests

PATCH Applied Dan Carpenter 2 participants 4 messages Jun 26, 2020 – Jul 15, 2020

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 drm/vmwgfx: Fix two list_for_each loop exit tests

These if statements are supposed to be true if we ended the list_for_each_entry() loops without hitting a break statement but they don't work.

In the first loop, we increment "i" after the "if (i = unit)" condition so we don't necessarily know that "i" is not equal to unit at the end of the loop.

In the second loop we exit when mode is not pointing to a valid drm_display_mode struct so it doesn't make sense to check "mode->type".

Fixes a278724aa23c ("drm/vmwgfx: Implement fbdev on kms v2")

---
I reversed the second condition as well, just because I was copy and pasting the exit condition. Plus I always feel like error handling is better than success handling. If anyone feel strongly, then I can send a v2.

 drivers/gpu/drm/vmwgfx/vmwgfx_kms.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/gpu/drm/vmwgfx/vmwgfx_kms.c +4 -4
index 3c97654b5a43..44168a7d7b44 100644
@@ -2576,7 +2576,7 @@ int vmw_kms_fbdev_init_data(struct vmw_private *dev_priv,
 		++i;
 	}
 
-	if (i != unit) {
+	if (&con->head = &dev_priv->dev->mode_config.connector_list) {
 		DRM_ERROR("Could not find initial display unit.\n");
 		ret = -EINVAL;
 		goto out_unlock;
@@ -2600,13 +2600,13 @@ int vmw_kms_fbdev_init_data(struct vmw_private *dev_priv,
 			break;
 	}
 
-	if (mode->type & DRM_MODE_TYPE_PREFERRED)
-		*p_mode = mode;
-	else {
+	if (&mode->head = &con->modes) {
 		WARN_ONCE(true, "Could not find initial preferred mode.\n");
 		*p_mode = list_first_entry(&con->modes,
 					   struct drm_display_mode,
 					   head);
+	} else {
+		*p_mode = mode;
 	}
 
  out_unlock:
Signature · 1 line
2.27.0
#1 lore raw

Am 26.06.20 um 12:39 schrieb Dan Carpenter:

Quoted 7 lines

These if statements are supposed to be true if we ended the list_for_each_entry() loops without hitting a break statement but they don't work.

In the first loop, we increment "i" after the "if (i = unit)" condition so we don't necessarily know that "i" is not equal to unit at the end of the loop.

So, if I understand this right, this would only really be a problem if there's no list entries at all, right? That is i = unit = 0.
Not sure if that can actually happen, but in any case the fix looks correct.

Quoted 3 lines

In the second loop we exit when mode is not pointing to a valid drm_display_mode struct so it doesn't make sense to check "mode->type".

Looks good to me too, condition order seems fine to me as well, though I wouldn't particularly care.

Applied to vmwgfx-next as well, thanks.

Roland

Quoted 43 lines
Fixes a278724aa23c ("drm/vmwgfx: Implement fbdev on kms v2")

---
I reversed the second condition as well, just because I was copy and pasting the exit condition. Plus I always feel like error handling is better than success handling. If anyone feel strongly, then I can send a v2.

 drivers/gpu/drm/vmwgfx/vmwgfx_kms.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/gpu/drm/vmwgfx/vmwgfx_kms.c +4 -4
index 3c97654b5a43..44168a7d7b44 100644
@@ -2576,7 +2576,7 @@ int vmw_kms_fbdev_init_data(struct vmw_private *dev_priv,
 		++i;
 	}
 
-	if (i != unit) {
+	if (&con->head = &dev_priv->dev->mode_config.connector_list) {
 		DRM_ERROR("Could not find initial display unit.\n");
 		ret = -EINVAL;
 		goto out_unlock;
@@ -2600,13 +2600,13 @@ int vmw_kms_fbdev_init_data(struct vmw_private *dev_priv,
 			break;
 	}
 
-	if (mode->type & DRM_MODE_TYPE_PREFERRED)
-		*p_mode = mode;
-	else {
+	if (&mode->head = &con->modes) {
 		WARN_ONCE(true, "Could not find initial preferred mode.\n");
 		*p_mode = list_first_entry(&con->modes,
 					   struct drm_display_mode,
 					   head);
+	} else {
+		*p_mode = mode;
 	}
 
  out_unlock:
#2 lore raw
Quoted 11 lines · Roland Scheidegger

Am 26.06.20 um 12:39 schrieb Dan Carpenter:

Quoted 7 lines

These if statements are supposed to be true if we ended the list_for_each_entry() loops without hitting a break statement but they don't work.

In the first loop, we increment "i" after the "if (i = unit)" condition so we don't necessarily know that "i" is not equal to unit at the end of the loop.

So, if I understand this right, this would only really be a problem if there's no list entries at all, right? That is i = unit = 0.
Not sure if that can actually happen, but in any case the fix looks correct.

An empty list and there is another potential issue where unit is exactly off by one.

	list_for_each_entry(con, &dev_priv->dev->mode_config.connector_list,
			    head) {
		if (i = unit)
			break;
		++i;  <-- this is the last iteration and it's off by one
			  so now i = unit but we didn't exit via the
			  break statement.
	}

	if (i != unit) {
            ^^^^^^^^^

Since we didn't exit by the break statement we want this to be true but it's false instead.

		DRM_ERROR("Could not find initial display unit.\n");

I don't know how *likely* this is, but static checkers complain. Technically correct is the best kind of correct! ;)

regards,
dan carpenter

#3 lore raw

Am 14.07.20 um 10:25 schrieb Dan Carpenter:

Quoted 27 lines · Roland Scheidegger
Quoted 11 lines

Am 26.06.20 um 12:39 schrieb Dan Carpenter:

Quoted 7 lines

These if statements are supposed to be true if we ended the list_for_each_entry() loops without hitting a break statement but they don't work.

In the first loop, we increment "i" after the "if (i = unit)" condition so we don't necessarily know that "i" is not equal to unit at the end of the loop.

So, if I understand this right, this would only really be a problem if there's no list entries at all, right? That is i = unit = 0.
Not sure if that can actually happen, but in any case the fix looks correct.

An empty list and there is another potential issue where unit is exactly off by one.

	list_for_each_entry(con, &dev_priv->dev->mode_config.connector_list,
			    head) {
		if (i = unit)
			break;
		++i;  <-- this is the last iteration and it's off by one
			  so now i = unit but we didn't exit via the
			  break statement.
	}

	if (i != unit) {
            ^^^^^^^^^
Quoted 7 lines

Since we didn't exit by the break statement we want this to be true but it's false instead.

		DRM_ERROR("Could not find initial display unit.\n");

I don't know how *likely* this is, but static checkers complain. Technically correct is the best kind of correct! ;)

Ahh indeed seems obvious now. But kinda difficult to spot :-).

Thanks again,

Roland

Quoted 4 lines

regards,
dan carpenter