Skip to contentSkip to conversation

phy: qcom-qmp: add V4 USB PHYs

PATCH Applied Jonathan Marek 4 participants 11 messages May 24, 2020 – Jun 29, 2020

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

cover phy: qcom-qmp: add V4 USB PHYs

Add support for sm8150 secondary USB PHY and both sm8250 USB PHYs.

Jonathan Marek (3):
phy: qcom-qmp: Allow different values for second lane
phy: qcom-qmp: Add QMP V4 USB3 UNIPHY
phy: qcom-qmp: Add QMP V4 USB3 PHY support for sm8250

 drivers/phy/qualcomm/phy-qcom-qmp.c | 408 +++++++++++++++++++++++++++-
 drivers/phy/qualcomm/phy-qcom-qmp.h |   7 +
 2 files changed, 403 insertions(+), 12 deletions(-)
Signature · 1 line
2.26.1
#1 lore raw

PATCH 1/3 phy: qcom-qmp: Allow different values for second lane

The primary USB PHY on sm8250 sets some values differently for the second lane. This makes it possible to represent that.

---
 drivers/phy/qualcomm/phy-qcom-qmp.c | 52 ++++++++++++++++++++++-------
 1 file changed, 40 insertions(+), 12 deletions(-)
drivers/phy/qualcomm/phy-qcom-qmp.c +40 -12
index e91040af3394..b3e07afca3ca 100644
@@ -82,20 +82,34 @@ struct qmp_phy_init_tbl {
 	 * register part of layout ?
 	 * if yes, then offset gives index in the reg-layout
 	 */
-	int in_layout;
+	bool in_layout;
+	/*
+	 * mask of lanes for which this register is written
+	 * for cases when second lane needs different values
+	 */
+	u8 lane_mask;
 };
 
 #define QMP_PHY_INIT_CFG(o, v)		\
 	{				\
 		.offset = o,		\
 		.val = v,		\
+		.lane_mask = 0xff,	\
 	}
 
 #define QMP_PHY_INIT_CFG_L(o, v)	\
 	{				\
 		.offset = o,		\
 		.val = v,		\
-		.in_layout = 1,		\
+		.in_layout = true,	\
+		.lane_mask = 0xff,	\
+	}
+
+#define QMP_PHY_INIT_CFG_LANE(o, v, l)	\
+	{				\
+		.offset = o,		\
+		.val = v,		\
+		.lane_mask = l,		\
 	}
 
 /* set of registers with offsets different per-PHY */
@@ -1986,10 +2000,11 @@ static const struct qmp_phy_cfg sm8150_usb3phy_cfg = {
 	.is_dual_lane_phy	= true,
 };
 
-static void qcom_qmp_phy_configure(void __iomem *base,
-				   const unsigned int *regs,
-				   const struct qmp_phy_init_tbl tbl[],
-				   int num)
+static void qcom_qmp_phy_configure_lane(void __iomem *base,
+					const unsigned int *regs,
+					const struct qmp_phy_init_tbl tbl[],
+					int num,
+					u8 lane_mask)
 {
 	int i;
 	const struct qmp_phy_init_tbl *t = tbl;
@@ -1998,6 +2013,9 @@ static void qcom_qmp_phy_configure(void __iomem *base,
 		return;
 
 	for (i = 0; i < num; i++, t++) {
+		if (!(t->lane_mask & lane_mask))
+			continue;
+
 		if (t->in_layout)
 			writel(t->val, base + regs[t->offset]);
 		else
@@ -2005,6 +2023,14 @@ static void qcom_qmp_phy_configure(void __iomem *base,
 	}
 }
 
+static void qcom_qmp_phy_configure(void __iomem *base,
+				   const unsigned int *regs,
+				   const struct qmp_phy_init_tbl tbl[],
+				   int num)
+{
+	qcom_qmp_phy_configure_lane(base, regs, tbl, num, 0xff);
+}
+
 static int qcom_qmp_phy_com_init(struct qmp_phy *qphy)
 {
 	struct qcom_qmp *qmp = qphy->qmp;
@@ -2219,16 +2245,18 @@ static int qcom_qmp_phy_enable(struct phy *phy)
 	}
 
 	/* Tx, Rx, and PCS configurations */
-	qcom_qmp_phy_configure(tx, cfg->regs, cfg->tx_tbl, cfg->tx_tbl_num);
+	qcom_qmp_phy_configure_lane(tx, cfg->regs,
+				    cfg->tx_tbl, cfg->tx_tbl_num, 1);
 	/* Configuration for other LANE for USB-DP combo PHY */
 	if (cfg->is_dual_lane_phy)
-		qcom_qmp_phy_configure(qphy->tx2, cfg->regs,
-				       cfg->tx_tbl, cfg->tx_tbl_num);
+		qcom_qmp_phy_configure_lane(qphy->tx2, cfg->regs,
+					    cfg->tx_tbl, cfg->tx_tbl_num, 2);
 
-	qcom_qmp_phy_configure(rx, cfg->regs, cfg->rx_tbl, cfg->rx_tbl_num);
+	qcom_qmp_phy_configure_lane(rx, cfg->regs,
+				    cfg->rx_tbl, cfg->rx_tbl_num, 1);
 	if (cfg->is_dual_lane_phy)
-		qcom_qmp_phy_configure(qphy->rx2, cfg->regs,
-				       cfg->rx_tbl, cfg->rx_tbl_num);
+		qcom_qmp_phy_configure_lane(qphy->rx2, cfg->regs,
+					    cfg->rx_tbl, cfg->rx_tbl_num, 2);
 
 	qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
 	ret = reset_control_deassert(qmp->ufs_reset);
Signature · 1 line
2.26.1
Reviewed-by on v1 1/3
#3 lore raw

Re: [PATCH 1/3] phy: qcom-qmp: Allow different values for second lane

In reply to Jonathan Marek
Quoted 91 lines · Jonathan Marek

The primary USB PHY on sm8250 sets some values differently for the second lane. This makes it possible to represent that.

---
 drivers/phy/qualcomm/phy-qcom-qmp.c | 52 ++++++++++++++++++++++-------
 1 file changed, 40 insertions(+), 12 deletions(-)
drivers/phy/qualcomm/phy-qcom-qmp.c +32 -6
index e91040af3394..b3e07afca3ca 100644
@@ -82,20 +82,34 @@ struct qmp_phy_init_tbl {
 	 * register part of layout ?
 	 * if yes, then offset gives index in the reg-layout
 	 */
-	int in_layout;
+	bool in_layout;
+	/*
+	 * mask of lanes for which this register is written
+	 * for cases when second lane needs different values
+	 */
+	u8 lane_mask;
 };
 
 #define QMP_PHY_INIT_CFG(o, v)		\
 	{				\
 		.offset = o,		\
 		.val = v,		\
+		.lane_mask = 0xff,	\
 	}
 
 #define QMP_PHY_INIT_CFG_L(o, v)	\
 	{				\
 		.offset = o,		\
 		.val = v,		\
-		.in_layout = 1,		\
+		.in_layout = true,	\
+		.lane_mask = 0xff,	\
+	}
+
+#define QMP_PHY_INIT_CFG_LANE(o, v, l)	\
+	{				\
+		.offset = o,		\
+		.val = v,		\
+		.lane_mask = l,		\
 	}
 
 /* set of registers with offsets different per-PHY */
@@ -1986,10 +2000,11 @@ static const struct qmp_phy_cfg sm8150_usb3phy_cfg = {
 	.is_dual_lane_phy	= true,
 };
 
-static void qcom_qmp_phy_configure(void __iomem *base,
-				   const unsigned int *regs,
-				   const struct qmp_phy_init_tbl tbl[],
-				   int num)
+static void qcom_qmp_phy_configure_lane(void __iomem *base,
+					const unsigned int *regs,
+					const struct qmp_phy_init_tbl tbl[],
+					int num,
+					u8 lane_mask)
 {
 	int i;
 	const struct qmp_phy_init_tbl *t = tbl;
@@ -1998,6 +2013,9 @@ static void qcom_qmp_phy_configure(void __iomem *base,
 		return;
 
 	for (i = 0; i < num; i++, t++) {
+		if (!(t->lane_mask & lane_mask))
+			continue;
+
 		if (t->in_layout)
 			writel(t->val, base + regs[t->offset]);
 		else
@@ -2005,6 +2023,14 @@ static void qcom_qmp_phy_configure(void __iomem *base,
 	}
 }
 
+static void qcom_qmp_phy_configure(void __iomem *base,
+				   const unsigned int *regs,
+				   const struct qmp_phy_init_tbl tbl[],
+				   int num)
+{
+	qcom_qmp_phy_configure_lane(base, regs, tbl, num, 0xff);
+}
+
 static int qcom_qmp_phy_com_init(struct qmp_phy *qphy)
 {
 	struct qcom_qmp *qmp = qphy->qmp;

drivers/phy/qualcomm/phy-qcom-qmp.c static int qcom_qmp_phy_enable(struct phy *phy) · line 2249

Quoted 6 lines
drivers/phy/qualcomm/phy-qcom-qmp.c +2 -1
@@ -2219,16 +2245,18 @@ static int qcom_qmp_phy_enable(struct phy *phy)
 	}
 
 	/* Tx, Rx, and PCS configurations */
-	qcom_qmp_phy_configure(tx, cfg->regs, cfg->tx_tbl, cfg->tx_tbl_num);
+	qcom_qmp_phy_configure_lane(tx, cfg->regs,
+				    cfg->tx_tbl, cfg->tx_tbl_num, 1);

Please ignore the 80-char suggestion and keep this on one line.

With that...

Regards,
Bjorn

Quoted 21 lines
drivers/phy/qualcomm/phy-qcom-qmp.c +6 -5
 	/* Configuration for other LANE for USB-DP combo PHY */
 	if (cfg->is_dual_lane_phy)
-		qcom_qmp_phy_configure(qphy->tx2, cfg->regs,
-				       cfg->tx_tbl, cfg->tx_tbl_num);
+		qcom_qmp_phy_configure_lane(qphy->tx2, cfg->regs,
+					    cfg->tx_tbl, cfg->tx_tbl_num, 2);
 
-	qcom_qmp_phy_configure(rx, cfg->regs, cfg->rx_tbl, cfg->rx_tbl_num);
+	qcom_qmp_phy_configure_lane(rx, cfg->regs,
+				    cfg->rx_tbl, cfg->rx_tbl_num, 1);
 	if (cfg->is_dual_lane_phy)
-		qcom_qmp_phy_configure(qphy->rx2, cfg->regs,
-				       cfg->rx_tbl, cfg->rx_tbl_num);
+		qcom_qmp_phy_configure_lane(qphy->rx2, cfg->regs,
+					    cfg->rx_tbl, cfg->rx_tbl_num, 2);
 
 	qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
 	ret = reset_control_deassert(qmp->ufs_reset);
Signature · 1 line
2.26.1
#4 lore raw

PATCH 2/3 phy: qcom-qmp: Add QMP V4 USB3 UNIPHY

In reply to Jonathan Marek

Add support for the USB3 PHY used by the secondary usb controller on sm8150

---
 drivers/phy/qualcomm/phy-qcom-qmp.c | 150 ++++++++++++++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-qmp.h |   5 +
 2 files changed, 155 insertions(+)
drivers/phy/qualcomm/phy-qcom-qmp.c +150 -0
index b3e07afca3ca..9367f8f793b5 100644
@@ -199,6 +199,17 @@ static const unsigned int qmp_v4_usb3phy_regs_layout[QPHY_LAYOUT_SIZE] = {
 	[QPHY_START_CTRL]		= 0x44,
 	[QPHY_PCS_STATUS]		= 0x14,
 	[QPHY_PCS_POWER_DOWN_CONTROL]	= 0x40,
+	[QPHY_PCS_AUTONOMOUS_MODE_CTRL]	= 0x308,
+	[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = 0x314,
+};
+
+static const unsigned int qmp_v4_usb3_uniphy_regs_layout[QPHY_LAYOUT_SIZE] = {
+	[QPHY_SW_RESET]			= 0x00,
+	[QPHY_START_CTRL]		= 0x44,
+	[QPHY_PCS_STATUS]		= 0x14,
+	[QPHY_PCS_POWER_DOWN_CONTROL]	= 0x40,
+	[QPHY_PCS_AUTONOMOUS_MODE_CTRL]	= 0x608,
+	[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR]  = 0x614,
 };
 
 static const unsigned int sdm845_ufsphy_regs_layout[QPHY_LAYOUT_SIZE] = {
@@ -1413,6 +1424,114 @@ static const struct qmp_phy_init_tbl sm8150_usb3_pcs_tbl[] = {
 	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_RXEQTRAINING_DFE_TIME_S2, 0x07),
 };
 
+static const struct qmp_phy_init_tbl sm8150_usb3_uniphy_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SYSCLK_EN_SEL, 0x1a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_HSCLK_SEL, 0x11),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_HSCLK_SEL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DEC_START_MODE0, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START1_MODE0, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START2_MODE0, 0xea),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START3_MODE0, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE0, 0xca),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE0, 0x1e),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CP_CTRL_MODE0, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE1_MODE0, 0x24),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP2_MODE0, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP1_MODE0, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP_EN, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SYSCLK_BUF_ENABLE, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE2_MODE1, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE1_MODE1, 0x24),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CORECLK_DIV_MODE1, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DEC_START_MODE1, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START1_MODE1, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START2_MODE1, 0xea),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START3_MODE1, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP2_MODE1, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP1_MODE1, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CP_CTRL_MODE1, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_RCTRL_MODE1, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_CCTRL_MODE1, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE1, 0xca),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE1, 0x1e),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CMN_IPTRIM, 0x20),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_EN_CENTER, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_PER1, 0x31),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_PER2, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE1_MODE1, 0xde),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE2_MODE1, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE1_MODE0, 0xde),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE2_MODE0, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE_MAP, 0x02),
+};
+
+static const struct qmp_phy_init_tbl sm8150_usb3_uniphy_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RCV_DETECT_LVL_2, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0x95),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_PI_QEC_CTRL, 0x40),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX, 0x05),
+};
+
+static const struct qmp_phy_init_tbl sm8150_usb3_uniphy_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0xb8),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0x37),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH, 0x2f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0xef),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb3),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x0b),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0x5c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xdc),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xdc),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0x99),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH1, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH2, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN1, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN2, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x2f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0xff),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL1, 0x54),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL2, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_EN_TIMER, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x47),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x0e),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET, 0x20),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c),
+};
+
+static const struct qmp_phy_init_tbl sm8150_usb3_uniphy_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG1, 0xd0),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG2, 0x07),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG3, 0x20),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG6, 0x13),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RX_SIGDET_LVL, 0xaa),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_UNI_RXEQTRAINING_DFE_TIME_S2, 0x07),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_UNI_LFPS_DET_HIGH_COUNT_VAL, 0xf8),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_CDR_RESET_TIME, 0x0f),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG1, 0x88),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG2, 0x13),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG1, 0x4b),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG5, 0x10),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x21),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c),
+};
+
 /* struct qmp_phy_cfg - per-PHY initialization config */
 struct qmp_phy_cfg {
 	/* phy-type - PCIE/UFS/USB */
@@ -2000,6 +2119,34 @@ static const struct qmp_phy_cfg sm8150_usb3phy_cfg = {
 	.is_dual_lane_phy	= true,
 };
 
+static const struct qmp_phy_cfg sm8150_usb3_uniphy_cfg = {
+	.type			= PHY_TYPE_USB3,
+	.nlanes			= 1,
+
+	.serdes_tbl		= sm8150_usb3_uniphy_serdes_tbl,
+	.serdes_tbl_num		= ARRAY_SIZE(sm8150_usb3_uniphy_serdes_tbl),
+	.tx_tbl			= sm8150_usb3_uniphy_tx_tbl,
+	.tx_tbl_num		= ARRAY_SIZE(sm8150_usb3_uniphy_tx_tbl),
+	.rx_tbl			= sm8150_usb3_uniphy_rx_tbl,
+	.rx_tbl_num		= ARRAY_SIZE(sm8150_usb3_uniphy_rx_tbl),
+	.pcs_tbl		= sm8150_usb3_uniphy_pcs_tbl,
+	.pcs_tbl_num		= ARRAY_SIZE(sm8150_usb3_uniphy_pcs_tbl),
+	.clk_list		= qmp_v4_phy_clk_l,
+	.num_clks		= ARRAY_SIZE(qmp_v4_phy_clk_l),
+	.reset_list		= msm8996_usb3phy_reset_l,
+	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
+	.vreg_list		= qmp_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
+	.regs			= qmp_v4_usb3_uniphy_regs_layout,
+
+	.start_ctrl		= SERDES_START | PCS_START,
+	.pwrdn_ctrl		= SW_PWRDN,
+
+	.has_pwrdn_delay	= true,
+	.pwrdn_delay_min	= POWER_DOWN_DELAY_US_MIN,
+	.pwrdn_delay_max	= POWER_DOWN_DELAY_US_MAX,
+};
+
 static void qcom_qmp_phy_configure_lane(void __iomem *base,
 					const unsigned int *regs,
 					const struct qmp_phy_init_tbl tbl[],
@@ -2774,6 +2921,9 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
 	}, {
 		.compatible = "qcom,sm8150-qmp-usb3-phy",
 		.data = &sm8150_usb3phy_cfg,
+	}, {
+		.compatible = "qcom,sm8150-qmp-usb3-uni-phy",
+		.data = &sm8150_usb3_uniphy_cfg,
 	},
 	{ },
 };
drivers/phy/qualcomm/phy-qcom-qmp.h +5 -0
index 6d017a0c0c8d..f39f7a968228 100644
@@ -363,6 +363,7 @@
 /* Only for QMP V4 PHY - TX registers */
 #define QSERDES_V4_TX_RES_CODE_LANE_TX			0x34
 #define QSERDES_V4_TX_RES_CODE_LANE_RX			0x38
+#define QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX 		0x3c
 #define QSERDES_V4_TX_LANE_MODE_1			0x84
 #define QSERDES_V4_TX_RCV_DETECT_LVL_2			0x9c
 #define QSERDES_V4_TX_PWM_GEAR_1_DIVIDER_BAND0_1	0xd8
@@ -709,6 +710,10 @@
 #define QPHY_V4_PCS_USB3_SIGDET_STARTUP_TIMER_VAL	0x354
 #define QPHY_V4_PCS_USB3_TEST_CONTROL			0x358
 
+/* Only for QMP V4 PHY - UNI has 0x300 offset for PCS_USB3 regs */
+#define QPHY_V4_PCS_USB3_UNI_LFPS_DET_HIGH_COUNT_VAL	0x618
+#define QPHY_V4_PCS_USB3_UNI_RXEQTRAINING_DFE_TIME_S2	0x638
+
 /* Only for QMP V4 PHY - PCS_MISC registers */
 #define QPHY_V4_PCS_MISC_TYPEC_CTRL			0x00
 #define QPHY_V4_PCS_MISC_TYPEC_PWRDN_CTRL		0x04
Signature · 1 line
2.26.1
Reviewed-by on v1 2/3
#6 lore raw

Re: [PATCH 2/3] phy: qcom-qmp: Add QMP V4 USB3 UNIPHY

In reply to Jonathan Marek
Quoted 3 lines · Jonathan Marek

Add support for the USB3 PHY used by the secondary usb controller on sm8150

I've not reviewed the individual register listings, but the rest looks good.

Regards,
Bjorn

Quoted 213 lines
---
 drivers/phy/qualcomm/phy-qcom-qmp.c | 150 ++++++++++++++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-qmp.h |   5 +
 2 files changed, 155 insertions(+)
drivers/phy/qualcomm/phy-qcom-qmp.c +150 -0
index b3e07afca3ca..9367f8f793b5 100644
@@ -199,6 +199,17 @@ static const unsigned int qmp_v4_usb3phy_regs_layout[QPHY_LAYOUT_SIZE] = {
 	[QPHY_START_CTRL]		= 0x44,
 	[QPHY_PCS_STATUS]		= 0x14,
 	[QPHY_PCS_POWER_DOWN_CONTROL]	= 0x40,
+	[QPHY_PCS_AUTONOMOUS_MODE_CTRL]	= 0x308,
+	[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = 0x314,
+};
+
+static const unsigned int qmp_v4_usb3_uniphy_regs_layout[QPHY_LAYOUT_SIZE] = {
+	[QPHY_SW_RESET]			= 0x00,
+	[QPHY_START_CTRL]		= 0x44,
+	[QPHY_PCS_STATUS]		= 0x14,
+	[QPHY_PCS_POWER_DOWN_CONTROL]	= 0x40,
+	[QPHY_PCS_AUTONOMOUS_MODE_CTRL]	= 0x608,
+	[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR]  = 0x614,
 };
 
 static const unsigned int sdm845_ufsphy_regs_layout[QPHY_LAYOUT_SIZE] = {
@@ -1413,6 +1424,114 @@ static const struct qmp_phy_init_tbl sm8150_usb3_pcs_tbl[] = {
 	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_RXEQTRAINING_DFE_TIME_S2, 0x07),
 };
 
+static const struct qmp_phy_init_tbl sm8150_usb3_uniphy_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SYSCLK_EN_SEL, 0x1a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_HSCLK_SEL, 0x11),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_HSCLK_SEL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DEC_START_MODE0, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START1_MODE0, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START2_MODE0, 0xea),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START3_MODE0, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE0, 0xca),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE0, 0x1e),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CP_CTRL_MODE0, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE1_MODE0, 0x24),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP2_MODE0, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP1_MODE0, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP_EN, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SYSCLK_BUF_ENABLE, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE2_MODE1, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE1_MODE1, 0x24),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CORECLK_DIV_MODE1, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DEC_START_MODE1, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START1_MODE1, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START2_MODE1, 0xea),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START3_MODE1, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP2_MODE1, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP1_MODE1, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CP_CTRL_MODE1, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_RCTRL_MODE1, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_CCTRL_MODE1, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE1, 0xca),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE1, 0x1e),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CMN_IPTRIM, 0x20),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_EN_CENTER, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_PER1, 0x31),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_PER2, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE1_MODE1, 0xde),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE2_MODE1, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE1_MODE0, 0xde),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE2_MODE0, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE_MAP, 0x02),
+};
+
+static const struct qmp_phy_init_tbl sm8150_usb3_uniphy_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RCV_DETECT_LVL_2, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0x95),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_PI_QEC_CTRL, 0x40),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX, 0x05),
+};
+
+static const struct qmp_phy_init_tbl sm8150_usb3_uniphy_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0xb8),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0x37),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH, 0x2f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0xef),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb3),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x0b),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0x5c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xdc),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xdc),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0x99),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH1, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH2, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN1, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN2, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x2f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0xff),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL1, 0x54),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL2, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_EN_TIMER, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x47),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x0e),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET, 0x20),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c),
+};
+
+static const struct qmp_phy_init_tbl sm8150_usb3_uniphy_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG1, 0xd0),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG2, 0x07),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG3, 0x20),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG6, 0x13),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RX_SIGDET_LVL, 0xaa),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_UNI_RXEQTRAINING_DFE_TIME_S2, 0x07),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_UNI_LFPS_DET_HIGH_COUNT_VAL, 0xf8),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_CDR_RESET_TIME, 0x0f),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG1, 0x88),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG2, 0x13),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG1, 0x4b),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG5, 0x10),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x21),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c),
+};
+
 /* struct qmp_phy_cfg - per-PHY initialization config */
 struct qmp_phy_cfg {
 	/* phy-type - PCIE/UFS/USB */
@@ -2000,6 +2119,34 @@ static const struct qmp_phy_cfg sm8150_usb3phy_cfg = {
 	.is_dual_lane_phy	= true,
 };
 
+static const struct qmp_phy_cfg sm8150_usb3_uniphy_cfg = {
+	.type			= PHY_TYPE_USB3,
+	.nlanes			= 1,
+
+	.serdes_tbl		= sm8150_usb3_uniphy_serdes_tbl,
+	.serdes_tbl_num		= ARRAY_SIZE(sm8150_usb3_uniphy_serdes_tbl),
+	.tx_tbl			= sm8150_usb3_uniphy_tx_tbl,
+	.tx_tbl_num		= ARRAY_SIZE(sm8150_usb3_uniphy_tx_tbl),
+	.rx_tbl			= sm8150_usb3_uniphy_rx_tbl,
+	.rx_tbl_num		= ARRAY_SIZE(sm8150_usb3_uniphy_rx_tbl),
+	.pcs_tbl		= sm8150_usb3_uniphy_pcs_tbl,
+	.pcs_tbl_num		= ARRAY_SIZE(sm8150_usb3_uniphy_pcs_tbl),
+	.clk_list		= qmp_v4_phy_clk_l,
+	.num_clks		= ARRAY_SIZE(qmp_v4_phy_clk_l),
+	.reset_list		= msm8996_usb3phy_reset_l,
+	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
+	.vreg_list		= qmp_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
+	.regs			= qmp_v4_usb3_uniphy_regs_layout,
+
+	.start_ctrl		= SERDES_START | PCS_START,
+	.pwrdn_ctrl		= SW_PWRDN,
+
+	.has_pwrdn_delay	= true,
+	.pwrdn_delay_min	= POWER_DOWN_DELAY_US_MIN,
+	.pwrdn_delay_max	= POWER_DOWN_DELAY_US_MAX,
+};
+
 static void qcom_qmp_phy_configure_lane(void __iomem *base,
 					const unsigned int *regs,
 					const struct qmp_phy_init_tbl tbl[],
@@ -2774,6 +2921,9 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
 	}, {
 		.compatible = "qcom,sm8150-qmp-usb3-phy",
 		.data = &sm8150_usb3phy_cfg,
+	}, {
+		.compatible = "qcom,sm8150-qmp-usb3-uni-phy",
+		.data = &sm8150_usb3_uniphy_cfg,
 	},
 	{ },
 };
drivers/phy/qualcomm/phy-qcom-qmp.h +5 -0
index 6d017a0c0c8d..f39f7a968228 100644
@@ -363,6 +363,7 @@
 /* Only for QMP V4 PHY - TX registers */
 #define QSERDES_V4_TX_RES_CODE_LANE_TX			0x34
 #define QSERDES_V4_TX_RES_CODE_LANE_RX			0x38
+#define QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX 		0x3c
 #define QSERDES_V4_TX_LANE_MODE_1			0x84
 #define QSERDES_V4_TX_RCV_DETECT_LVL_2			0x9c
 #define QSERDES_V4_TX_PWM_GEAR_1_DIVIDER_BAND0_1	0xd8
@@ -709,6 +710,10 @@
 #define QPHY_V4_PCS_USB3_SIGDET_STARTUP_TIMER_VAL	0x354
 #define QPHY_V4_PCS_USB3_TEST_CONTROL			0x358
 
+/* Only for QMP V4 PHY - UNI has 0x300 offset for PCS_USB3 regs */
+#define QPHY_V4_PCS_USB3_UNI_LFPS_DET_HIGH_COUNT_VAL	0x618
+#define QPHY_V4_PCS_USB3_UNI_RXEQTRAINING_DFE_TIME_S2	0x638
+
 /* Only for QMP V4 PHY - PCS_MISC registers */
 #define QPHY_V4_PCS_MISC_TYPEC_CTRL			0x00
 #define QPHY_V4_PCS_MISC_TYPEC_PWRDN_CTRL		0x04
Signature · 1 line
2.26.1
#7 lore raw

PATCH 3/3 phy: qcom-qmp: Add QMP V4 USB3 PHY support for sm8250

In reply to Jonathan Marek

Add both the DP and UNI PHY for primary/secondary usb controllers.

The tables are very similar to sm8150 (serdes_tbl is identical), but there are some differences.

---
 drivers/phy/qualcomm/phy-qcom-qmp.c | 206 ++++++++++++++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-qmp.h |   2 +
 2 files changed, 208 insertions(+)
drivers/phy/qualcomm/phy-qcom-qmp.c +206 -0
index 9367f8f793b5..8a597cedfebe 100644
@@ -1532,6 +1532,142 @@ static const struct qmp_phy_init_tbl sm8150_usb3_uniphy_pcs_tbl[] = {
 	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c),
 };
 
+static const struct qmp_phy_init_tbl sm8250_usb3_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_TX, 0x60),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_RX, 0x60),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX, 0x11),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_RX, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0xd5),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RCV_DETECT_LVL_2, 0x12),
+	QMP_PHY_INIT_CFG_LANE(QSERDES_V4_TX_PI_QEC_CTRL, 0x40, 1),
+	QMP_PHY_INIT_CFG_LANE(QSERDES_V4_TX_PI_QEC_CTRL, 0x54, 2),
+};
+
+static const struct qmp_phy_init_tbl sm8250_usb3_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x2f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0xff),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0x99),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH1, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH2, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN1, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN2, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL1, 0x54),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL2, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x0e),
+	QMP_PHY_INIT_CFG_LANE(QSERDES_V4_RX_RX_MODE_00_LOW, 0xff, 1),
+	QMP_PHY_INIT_CFG_LANE(QSERDES_V4_RX_RX_MODE_00_LOW, 0x7f, 2),
+	QMP_PHY_INIT_CFG_LANE(QSERDES_V4_RX_RX_MODE_00_HIGH, 0x7f, 1),
+	QMP_PHY_INIT_CFG_LANE(QSERDES_V4_RX_RX_MODE_00_HIGH, 0xff, 2),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0x97),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xdc),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xdc),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0x5c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x7b),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb4),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_EN_TIMER, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_AUX_DATA_TCOARSE_TFINE, 0xa0),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VTH_CODE, 0x10),
+};
+
+static const struct qmp_phy_init_tbl sm8250_usb3_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG1, 0xd0),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG2, 0x07),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG3, 0x20),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG6, 0x13),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x21),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RX_SIGDET_LVL, 0xa9),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_CDR_RESET_TIME, 0x0a),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG1, 0x88),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG2, 0x13),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG1, 0x4b),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG5, 0x10),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_LFPS_DET_HIGH_COUNT_VAL, 0xf8),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_RXEQTRAINING_DFE_TIME_S2, 0x07),
+};
+
+static const struct qmp_phy_init_tbl sm8250_usb3_uniphy_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RCV_DETECT_LVL_2, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0xd5),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_2, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_PI_QEC_CTRL, 0x40),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX, 0x11),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_RX, 0x02),
+};
+
+static const struct qmp_phy_init_tbl sm8250_usb3_uniphy_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0xb8),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0xff),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0xbf),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb4),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x7b),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0x5c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xdc),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xdc),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0x99),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH1, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH2, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN1, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN2, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x2f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0xff),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL1, 0x54),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL2, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_EN_TIMER, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x47),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x0e),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x1f),
+};
+
+static const struct qmp_phy_init_tbl sm8250_usb3_uniphy_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG1, 0xd0),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG2, 0x07),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG3, 0x20),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG6, 0x13),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RX_SIGDET_LVL, 0xa9),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_UNI_RXEQTRAINING_DFE_TIME_S2, 0x07),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_UNI_LFPS_DET_HIGH_COUNT_VAL, 0xf8),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_CDR_RESET_TIME, 0x0a),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG1, 0x88),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG2, 0x13),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG1, 0x4b),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG5, 0x10),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x21),
+};
+
 /* struct qmp_phy_cfg - per-PHY initialization config */
 struct qmp_phy_cfg {
 	/* phy-type - PCIE/UFS/USB */
@@ -1700,6 +1836,11 @@ static const char * const qmp_v4_phy_clk_l[] = {
 	"aux", "ref_clk_src", "ref", "com_aux",
 };
 
+/* the primary usb3 phy on sm8250 doesn't have a ref clock */
+static const char * const qmp_v4_sm8250_usbphy_clk_l[] = {
+	"aux", "ref_clk_src", "com_aux"
+};
+
 static const char * const sdm845_ufs_phy_clk_l[] = {
 	"ref", "ref_aux",
 };
@@ -2147,6 +2288,65 @@ static const struct qmp_phy_cfg sm8150_usb3_uniphy_cfg = {
 	.pwrdn_delay_max	= POWER_DOWN_DELAY_US_MAX,
 };
 
+static const struct qmp_phy_cfg sm8250_usb3phy_cfg = {
+	.type			= PHY_TYPE_USB3,
+	.nlanes			= 1,
+
+	.serdes_tbl		= sm8150_usb3_serdes_tbl,
+	.serdes_tbl_num		= ARRAY_SIZE(sm8150_usb3_serdes_tbl),
+	.tx_tbl			= sm8250_usb3_tx_tbl,
+	.tx_tbl_num		= ARRAY_SIZE(sm8250_usb3_tx_tbl),
+	.rx_tbl			= sm8250_usb3_rx_tbl,
+	.rx_tbl_num		= ARRAY_SIZE(sm8250_usb3_rx_tbl),
+	.pcs_tbl		= sm8250_usb3_pcs_tbl,
+	.pcs_tbl_num		= ARRAY_SIZE(sm8250_usb3_pcs_tbl),
+	.clk_list		= qmp_v4_sm8250_usbphy_clk_l,
+	.num_clks		= ARRAY_SIZE(qmp_v4_sm8250_usbphy_clk_l),
+	.reset_list		= msm8996_usb3phy_reset_l,
+	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
+	.vreg_list		= qmp_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
+	.regs			= qmp_v4_usb3phy_regs_layout,
+
+	.start_ctrl		= SERDES_START | PCS_START,
+	.pwrdn_ctrl		= SW_PWRDN,
+
+	.has_pwrdn_delay	= true,
+	.pwrdn_delay_min	= POWER_DOWN_DELAY_US_MIN,
+	.pwrdn_delay_max	= POWER_DOWN_DELAY_US_MAX,
+
+	.has_phy_dp_com_ctrl	= true,
+	.is_dual_lane_phy	= true,
+};
+
+static const struct qmp_phy_cfg sm8250_usb3_uniphy_cfg = {
+	.type			= PHY_TYPE_USB3,
+	.nlanes			= 1,
+
+	.serdes_tbl		= sm8150_usb3_uniphy_serdes_tbl,
+	.serdes_tbl_num		= ARRAY_SIZE(sm8150_usb3_uniphy_serdes_tbl),
+	.tx_tbl			= sm8250_usb3_uniphy_tx_tbl,
+	.tx_tbl_num		= ARRAY_SIZE(sm8250_usb3_uniphy_tx_tbl),
+	.rx_tbl			= sm8250_usb3_uniphy_rx_tbl,
+	.rx_tbl_num		= ARRAY_SIZE(sm8250_usb3_uniphy_rx_tbl),
+	.pcs_tbl		= sm8250_usb3_uniphy_pcs_tbl,
+	.pcs_tbl_num		= ARRAY_SIZE(sm8250_usb3_uniphy_pcs_tbl),
+	.clk_list		= qmp_v4_phy_clk_l,
+	.num_clks		= ARRAY_SIZE(qmp_v4_phy_clk_l),
+	.reset_list		= msm8996_usb3phy_reset_l,
+	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
+	.vreg_list		= qmp_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
+	.regs			= qmp_v4_usb3_uniphy_regs_layout,
+
+	.start_ctrl		= SERDES_START | PCS_START,
+	.pwrdn_ctrl		= SW_PWRDN,
+
+	.has_pwrdn_delay	= true,
+	.pwrdn_delay_min	= POWER_DOWN_DELAY_US_MIN,
+	.pwrdn_delay_max	= POWER_DOWN_DELAY_US_MAX,
+};
+
 static void qcom_qmp_phy_configure_lane(void __iomem *base,
 					const unsigned int *regs,
 					const struct qmp_phy_init_tbl tbl[],
@@ -2924,6 +3124,12 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
 	}, {
 		.compatible = "qcom,sm8150-qmp-usb3-uni-phy",
 		.data = &sm8150_usb3_uniphy_cfg,
+	}, {
+		.compatible = "qcom,sm8250-qmp-usb3-phy",
+		.data = &sm8250_usb3phy_cfg,
+	}, {
+		.compatible = "qcom,sm8250-qmp-usb3-uni-phy",
+		.data = &sm8250_usb3_uniphy_cfg,
 	},
 	{ },
 };
drivers/phy/qualcomm/phy-qcom-qmp.h +2 -0
index f39f7a968228..4277f592684b 100644
@@ -364,7 +364,9 @@
 #define QSERDES_V4_TX_RES_CODE_LANE_TX			0x34
 #define QSERDES_V4_TX_RES_CODE_LANE_RX			0x38
 #define QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX 		0x3c
+#define QSERDES_V4_TX_RES_CODE_LANE_OFFSET_RX 		0x40
 #define QSERDES_V4_TX_LANE_MODE_1			0x84
+#define QSERDES_V4_TX_LANE_MODE_2			0x88
 #define QSERDES_V4_TX_RCV_DETECT_LVL_2			0x9c
 #define QSERDES_V4_TX_PWM_GEAR_1_DIVIDER_BAND0_1	0xd8
 #define QSERDES_V4_TX_PWM_GEAR_2_DIVIDER_BAND0_1	0xdC
Signature · 1 line
2.26.1
Reviewed-by on v1 3/3
#9 lore raw

Re: [PATCH 3/3] phy: qcom-qmp: Add QMP V4 USB3 PHY support for sm8250

In reply to Jonathan Marek
Quoted 6 lines · Jonathan Marek

Add both the DP and UNI PHY for primary/secondary usb controllers.

The tables are very similar to sm8150 (serdes_tbl is identical), but there are some differences.

Regards,
Bjorn

Quoted 260 lines
---
 drivers/phy/qualcomm/phy-qcom-qmp.c | 206 ++++++++++++++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-qmp.h |   2 +
 2 files changed, 208 insertions(+)
drivers/phy/qualcomm/phy-qcom-qmp.c +206 -0
index 9367f8f793b5..8a597cedfebe 100644
@@ -1532,6 +1532,142 @@ static const struct qmp_phy_init_tbl sm8150_usb3_uniphy_pcs_tbl[] = {
 	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c),
 };
 
+static const struct qmp_phy_init_tbl sm8250_usb3_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_TX, 0x60),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_RX, 0x60),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX, 0x11),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_RX, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0xd5),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RCV_DETECT_LVL_2, 0x12),
+	QMP_PHY_INIT_CFG_LANE(QSERDES_V4_TX_PI_QEC_CTRL, 0x40, 1),
+	QMP_PHY_INIT_CFG_LANE(QSERDES_V4_TX_PI_QEC_CTRL, 0x54, 2),
+};
+
+static const struct qmp_phy_init_tbl sm8250_usb3_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x2f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0xff),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0x99),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH1, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH2, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN1, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN2, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL1, 0x54),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL2, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x0e),
+	QMP_PHY_INIT_CFG_LANE(QSERDES_V4_RX_RX_MODE_00_LOW, 0xff, 1),
+	QMP_PHY_INIT_CFG_LANE(QSERDES_V4_RX_RX_MODE_00_LOW, 0x7f, 2),
+	QMP_PHY_INIT_CFG_LANE(QSERDES_V4_RX_RX_MODE_00_HIGH, 0x7f, 1),
+	QMP_PHY_INIT_CFG_LANE(QSERDES_V4_RX_RX_MODE_00_HIGH, 0xff, 2),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0x97),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xdc),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xdc),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0x5c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x7b),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb4),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_EN_TIMER, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_AUX_DATA_TCOARSE_TFINE, 0xa0),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VTH_CODE, 0x10),
+};
+
+static const struct qmp_phy_init_tbl sm8250_usb3_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG1, 0xd0),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG2, 0x07),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG3, 0x20),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG6, 0x13),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x21),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RX_SIGDET_LVL, 0xa9),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_CDR_RESET_TIME, 0x0a),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG1, 0x88),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG2, 0x13),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG1, 0x4b),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG5, 0x10),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_LFPS_DET_HIGH_COUNT_VAL, 0xf8),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_RXEQTRAINING_DFE_TIME_S2, 0x07),
+};
+
+static const struct qmp_phy_init_tbl sm8250_usb3_uniphy_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RCV_DETECT_LVL_2, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0xd5),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_2, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_PI_QEC_CTRL, 0x40),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX, 0x11),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_RX, 0x02),
+};
+
+static const struct qmp_phy_init_tbl sm8250_usb3_uniphy_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0xb8),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0xff),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0xbf),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb4),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x7b),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0x5c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xdc),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xdc),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0x99),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH1, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH2, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN1, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN2, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x2f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0xff),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL1, 0x54),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL2, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_EN_TIMER, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x47),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x0e),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x1f),
+};
+
+static const struct qmp_phy_init_tbl sm8250_usb3_uniphy_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG1, 0xd0),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG2, 0x07),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG3, 0x20),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG6, 0x13),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RX_SIGDET_LVL, 0xa9),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_UNI_RXEQTRAINING_DFE_TIME_S2, 0x07),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_UNI_LFPS_DET_HIGH_COUNT_VAL, 0xf8),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_CDR_RESET_TIME, 0x0a),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG1, 0x88),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG2, 0x13),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG1, 0x4b),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG5, 0x10),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x21),
+};
+
 /* struct qmp_phy_cfg - per-PHY initialization config */
 struct qmp_phy_cfg {
 	/* phy-type - PCIE/UFS/USB */
@@ -1700,6 +1836,11 @@ static const char * const qmp_v4_phy_clk_l[] = {
 	"aux", "ref_clk_src", "ref", "com_aux",
 };
 
+/* the primary usb3 phy on sm8250 doesn't have a ref clock */
+static const char * const qmp_v4_sm8250_usbphy_clk_l[] = {
+	"aux", "ref_clk_src", "com_aux"
+};
+
 static const char * const sdm845_ufs_phy_clk_l[] = {
 	"ref", "ref_aux",
 };
@@ -2147,6 +2288,65 @@ static const struct qmp_phy_cfg sm8150_usb3_uniphy_cfg = {
 	.pwrdn_delay_max	= POWER_DOWN_DELAY_US_MAX,
 };
 
+static const struct qmp_phy_cfg sm8250_usb3phy_cfg = {
+	.type			= PHY_TYPE_USB3,
+	.nlanes			= 1,
+
+	.serdes_tbl		= sm8150_usb3_serdes_tbl,
+	.serdes_tbl_num		= ARRAY_SIZE(sm8150_usb3_serdes_tbl),
+	.tx_tbl			= sm8250_usb3_tx_tbl,
+	.tx_tbl_num		= ARRAY_SIZE(sm8250_usb3_tx_tbl),
+	.rx_tbl			= sm8250_usb3_rx_tbl,
+	.rx_tbl_num		= ARRAY_SIZE(sm8250_usb3_rx_tbl),
+	.pcs_tbl		= sm8250_usb3_pcs_tbl,
+	.pcs_tbl_num		= ARRAY_SIZE(sm8250_usb3_pcs_tbl),
+	.clk_list		= qmp_v4_sm8250_usbphy_clk_l,
+	.num_clks		= ARRAY_SIZE(qmp_v4_sm8250_usbphy_clk_l),
+	.reset_list		= msm8996_usb3phy_reset_l,
+	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
+	.vreg_list		= qmp_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
+	.regs			= qmp_v4_usb3phy_regs_layout,
+
+	.start_ctrl		= SERDES_START | PCS_START,
+	.pwrdn_ctrl		= SW_PWRDN,
+
+	.has_pwrdn_delay	= true,
+	.pwrdn_delay_min	= POWER_DOWN_DELAY_US_MIN,
+	.pwrdn_delay_max	= POWER_DOWN_DELAY_US_MAX,
+
+	.has_phy_dp_com_ctrl	= true,
+	.is_dual_lane_phy	= true,
+};
+
+static const struct qmp_phy_cfg sm8250_usb3_uniphy_cfg = {
+	.type			= PHY_TYPE_USB3,
+	.nlanes			= 1,
+
+	.serdes_tbl		= sm8150_usb3_uniphy_serdes_tbl,
+	.serdes_tbl_num		= ARRAY_SIZE(sm8150_usb3_uniphy_serdes_tbl),
+	.tx_tbl			= sm8250_usb3_uniphy_tx_tbl,
+	.tx_tbl_num		= ARRAY_SIZE(sm8250_usb3_uniphy_tx_tbl),
+	.rx_tbl			= sm8250_usb3_uniphy_rx_tbl,
+	.rx_tbl_num		= ARRAY_SIZE(sm8250_usb3_uniphy_rx_tbl),
+	.pcs_tbl		= sm8250_usb3_uniphy_pcs_tbl,
+	.pcs_tbl_num		= ARRAY_SIZE(sm8250_usb3_uniphy_pcs_tbl),
+	.clk_list		= qmp_v4_phy_clk_l,
+	.num_clks		= ARRAY_SIZE(qmp_v4_phy_clk_l),
+	.reset_list		= msm8996_usb3phy_reset_l,
+	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
+	.vreg_list		= qmp_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
+	.regs			= qmp_v4_usb3_uniphy_regs_layout,
+
+	.start_ctrl		= SERDES_START | PCS_START,
+	.pwrdn_ctrl		= SW_PWRDN,
+
+	.has_pwrdn_delay	= true,
+	.pwrdn_delay_min	= POWER_DOWN_DELAY_US_MIN,
+	.pwrdn_delay_max	= POWER_DOWN_DELAY_US_MAX,
+};
+
 static void qcom_qmp_phy_configure_lane(void __iomem *base,
 					const unsigned int *regs,
 					const struct qmp_phy_init_tbl tbl[],
@@ -2924,6 +3124,12 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
 	}, {
 		.compatible = "qcom,sm8150-qmp-usb3-uni-phy",
 		.data = &sm8150_usb3_uniphy_cfg,
+	}, {
+		.compatible = "qcom,sm8250-qmp-usb3-phy",
+		.data = &sm8250_usb3phy_cfg,
+	}, {
+		.compatible = "qcom,sm8250-qmp-usb3-uni-phy",
+		.data = &sm8250_usb3_uniphy_cfg,
 	},
 	{ },
 };
drivers/phy/qualcomm/phy-qcom-qmp.h +2 -0
index f39f7a968228..4277f592684b 100644
@@ -364,7 +364,9 @@
 #define QSERDES_V4_TX_RES_CODE_LANE_TX			0x34
 #define QSERDES_V4_TX_RES_CODE_LANE_RX			0x38
 #define QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX 		0x3c
+#define QSERDES_V4_TX_RES_CODE_LANE_OFFSET_RX 		0x40
 #define QSERDES_V4_TX_LANE_MODE_1			0x84
+#define QSERDES_V4_TX_LANE_MODE_2			0x88
 #define QSERDES_V4_TX_RCV_DETECT_LVL_2			0x9c
 #define QSERDES_V4_TX_PWM_GEAR_1_DIVIDER_BAND0_1	0xd8
 #define QSERDES_V4_TX_PWM_GEAR_2_DIVIDER_BAND0_1	0xdC
Signature · 1 line
2.26.1
maintainer Applied
#10 lore raw
In reply to Jonathan Marek
Quoted 1 line · Jonathan Marek

Add support for sm8150 secondary USB PHY and both sm8250 USB PHYs.

Applied all, thanks

Signature · 1 line
~Vinod