sifive: fu540: Add Booting from SPI
Subsystems (2)
PATCH v4 2/6 sifive: fu540: Add Booting from SPI
Add booting from SPI for SiFive Unleashed board.
---
Changes for v4:
- drop BOARD configs
.../dts/hifive-unleashed-a00-u-boot.dtsi | 12 ++++++ configs/sifive_fu540_defconfig | 4 ++ doc/board/sifive/fu540.rst | 41 +++++++++++++++++++ 3 files changed, 57 insertions(+)
arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi +12 -0
@@ -12,6 +12,10 @@ spi2 = &qspi2; }; + config { + u-boot,spl-payload-offset = <0x105000>; /* loader2 @1044KB */ + }; + hfclk { u-boot,dm-spl; };
@@ -22,6 +26,14 @@ }; +&qspi0 { + u-boot,dm-spl; + + flash at 0 { + u-boot,dm-spl; + }; +}; + &qspi2 { mmc at 0 { u-boot,dm-spl;
configs/sifive_fu540_defconfig +4 -0
@@ -2,9 +2,11 @@ CONFIG_RISCV=y CONFIG_SPL_GPIO_SUPPORT=y CONFIG_SYS_MALLOC_F_LEN=0x3000 CONFIG_ENV_SIZE=0x20000 +CONFIG_SPL_DM_SPI=y CONFIG_SPL_MMC_SUPPORT=y CONFIG_NR_DRAM_BANKS=1 CONFIG_SPL=y +CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y CONFIG_TARGET_SIFIVE_FU540=y CONFIG_ARCH_RV64I=y
@@ -15,9 +17,11 @@ CONFIG_MISC_INIT_R=y CONFIG_DISPLAY_CPUINFO=y CONFIG_DISPLAY_BOARDINFO=y CONFIG_SPL_SEPARATE_BSS=y +CONFIG_SPL_SPI_LOAD=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_OF_BOARD_FIXUP=y CONFIG_DEFAULT_DEVICE_TREE="hifive-unleashed-a00" CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_SPL_DM_SEQ_ALIAS=y CONFIG_SPL_CLK=y CONFIG_DM_MTD=y
doc/board/sifive/fu540.rst +41 -0
44 lines not on this page · raw message
Signature · 1 line
2.25.1
PATCH v4 3/6 env: Enable SPI flash env for SiFive FU540
SPI flash device on HiFive Unleashed has 32MiB Size.
This patch adds SPI flash environment after U-Boot proper partition with a size of 128KiB.
SPI flash partition layout(32MiB):
0 - 34 : reserved for GPT header
35 - 39 : unused
40 - 2087 : loader1 (SPL, FSBL)
2088 - 10279 : loader2 (U-Boot proper, U-Boot)
10280 - 10535 : environment
10536 - 65494 : rootfs
65528 - 65536 : distro script
Note: the loader1 must start from 40th sector even though there are 6 free sectors prior since 40th sector is nearest flash sector boundary.?
---
Changes for v4:
- %s/add/adds
arch/riscv/cpu/fu540/Kconfig | 13 +++++++++++++ 1 file changed, 13 insertions(+)
arch/riscv/cpu/fu540/Kconfig +13 -0
@@ -13,3 +13,16 @@ config SIFIVE_FU540 imply SPL_CPU_SUPPORT imply SPL_OPENSBI imply SPL_LOAD_FIT + +if ENV_IS_IN_SPI_FLASH + +config ENV_OFFSET + default 0x505000 + +config ENV_SIZE + default 0x20000 + +config ENV_SECT_SIZE + default 0x10000 + +endif # ENV_IS_IN_SPI_FLASH
Signature · 1 line
2.25.1
A message that is not in the archive (sent off-list or not yet received): [email protected]
PATCH v4 2/6 sifive: fu540: Add Booting from SPI
Hi Jagan
Quoted 6 lines
From: Jagan Teki [mailto:jagan at amarulasolutions.com]
Sent: Thursday, July 02, 2020 4:03 PM
To: Rick Jian-Zhi Chen(???); Atish Patra; Palmer Dabbelt; Bin Meng; Paul Walmsley; Anup Patel; Sagar Kadam
Cc: u-boot at lists.denx.de; linux-amarula at amarulasolutions.com; Jagan Teki; Bin Meng
Subject: [PATCH v4 2/6] sifive: fu540: Add Booting from SPI
Quoted 9 lines
Add booting from SPI for SiFive Unleashed board.
Signed-off-by Jagan Teki <[email protected]>Reviewed-by Bin Meng <[email protected]>Tested-by Bin Meng <[email protected]>---
Changes for v4:
- drop BOARD configs
Can you rebase and send the whole patches of v4 again ? When I tried to pick up others from v3, there have some conflicts.
Thanks,
Rick
Quoted 114 lines
.../dts/hifive-unleashed-a00-u-boot.dtsi | 12 ++++++ configs/sifive_fu540_defconfig | 4 ++ doc/board/sifive/fu540.rst | 41 +++++++++++++++++++ 3 files changed, 57 insertions(+)arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi +12
-0@@ -12,6 +12,10 @@ spi2 = &qspi2; }; + config { + u-boot,spl-payload-offset = <0x105000>; /* loader2 @1044KB */ + }; + hfclk { u-boot,dm-spl; };@@ -22,6 +26,14 @@ }; +&qspi0 { + u-boot,dm-spl; + + flash at 0 { + u-boot,dm-spl; + }; +}; + &qspi2 { mmc at 0 { u-boot,dm-spl;configs/sifive_fu540_defconfig +4
-0@@ -2,9 +2,11 @@ CONFIG_RISCV=y CONFIG_SPL_GPIO_SUPPORT=y CONFIG_SYS_MALLOC_F_LEN=0x3000 CONFIG_ENV_SIZE=0x20000 +CONFIG_SPL_DM_SPI=y CONFIG_SPL_MMC_SUPPORT=y CONFIG_NR_DRAM_BANKS=1 CONFIG_SPL=y +CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y CONFIG_TARGET_SIFIVE_FU540=y CONFIG_ARCH_RV64I=y@@ -15,9 +17,11 @@ CONFIG_MISC_INIT_R=y CONFIG_DISPLAY_CPUINFO=y CONFIG_DISPLAY_BOARDINFO=y CONFIG_SPL_SEPARATE_BSS=y +CONFIG_SPL_SPI_LOAD=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_OF_BOARD_FIXUP=y CONFIG_DEFAULT_DEVICE_TREE="hifive-unleashed-a00" CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_SPL_DM_SEQ_ALIAS=y CONFIG_SPL_CLK=y CONFIG_DM_MTD=ydoc/board/sifive/fu540.rst +42
-1@@ -533,3 +533,44 @@ Sample boot log from HiFive Unleashed board type: 0fc63daf-8483-4772-8e79-3d69d8477de4 type: linux guid: 9faa81b6-39b1-4418-af5e-89c48f29c20d + +Booting from SPI +---------------- + +Use Building steps from "Booting from MMC using U-Boot SPL" section. + +Partition the SPI in Linux via mtdblock. (Require to boot the board in +SD boot mode by enabling MTD block in Linux) + +Use prebuilt image from here [1], which support to partition the SPI flash. + +.. code-block:: none + + # sgdisk --clear \ + > --set-alignment=2 \ + > --new=1:40:2087 --change-name=1:loader1 + --typecode=1:5B193300-FC78-40CD-8002-E86C45580B47 \ > + --new=2:2088:10279 --change-name=2:loader2 + --typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \ > + --new=3:10536:65494 --change-name=3:rootfs + --typecode=3:0FC63DAF-8483-4772-8E79-3D69D8477DE4 \ > /dev/mtdblock0 + +Program the SPI (Require to boot the board in SD boot mode) + +Execute below steps on U-Boot proper, + +.. code-block:: none + + tftpboot $kernel_addr_r u-boot-spl.bin sf erase 0x5000 $filesize sf + write $kernel_addr_r 0x5000 $filesize + + tftpboot $kernel_addr_r u-boot.itb + sf erase 0x105000 $filesize + sf write $kernel_addr_r 0x105000 $filesize + +Power off the board + +Change DIP switches MSEL[3:0] are set to 0110 + +Power up the board. + +[1] https://github.com/amarula/bsp-sifive --2.25.1