Skip to contentSkip to conversation

arm64: dts: qcom: smmu/USB nodes and HDK855/HDK865 dts

PATCH Applied Jonathan Marek 5 participants 15 messages Jun 9, 2020 – Jul 9, 2020

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

v2 cover arm64: dts: qcom: smmu/USB nodes and HDK855/HDK865 dts

Add dts nodes for apps_smmu and USB for both sm8150 and sm8250.

Also add initial dts files for HDK855 and HDK865, based on mtp dts, with a few changes. Notably, the HDK865 dts has regulator config changed a bit based on downstream (I think sm8250-mtp.dts is wrong and copied too much from sm8150).

V2 changes:
* Added two patches for sm8150 and sm8250 iommu compatibles
* Changed apps_smmu node patches to use new compatibles
* Updated commit messages for apps_smmu patches to be more correct
* Updated HDK dts patches based on Bjorn's comments

Jonathan Marek (8):
dt-bindings: arm-smmu: Add sm8150 and sm8250 compatible strings
iommu: arm-smmu-impl: Use qcom impl for sm8150 and sm8250 compatibles
arm64: dts: qcom: sm8150: add apps_smmu node
arm64: dts: qcom: sm8250: add apps_smmu node
arm64: dts: qcom: sm8150: Add secondary USB and PHY nodes
arm64: dts: qcom: sm8250: Add USB and PHY device nodes
arm64: dts: qcom: add sm8150 hdk dts
arm64: dts: qcom: add sm8250 hdk dts

 .../devicetree/bindings/iommu/arm,smmu.yaml   |   2 +
 arch/arm64/boot/dts/qcom/Makefile             |   2 +
 arch/arm64/boot/dts/qcom/sm8150-hdk.dts       | 463 ++++++++++++++++++
 arch/arm64/boot/dts/qcom/sm8150.dtsi          | 180 +++++++
 arch/arm64/boot/dts/qcom/sm8250-hdk.dts       | 454 +++++++++++++++++
 arch/arm64/boot/dts/qcom/sm8250.dtsi          | 287 +++++++++++
 drivers/iommu/arm-smmu-impl.c                 |   4 +-
 7 files changed, 1391 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm64/boot/dts/qcom/sm8150-hdk.dts
 create mode 100644 arch/arm64/boot/dts/qcom/sm8250-hdk.dts
Signature · 1 line
2.26.1
#1 lore raw

PATCH v2 1/8 dt-bindings: arm-smmu: Add sm8150 and sm8250 compatible strings

Add compatible strings for sm8150 and sm8250 iommus to documentation.

---
 Documentation/devicetree/bindings/iommu/arm,smmu.yaml | 2 ++
 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/iommu/arm,smmu.yaml +2 -0
index d7ceb4c34423..3ac741236c8b 100644
@@ -37,6 +37,8 @@ properties:
           - enum:
               - qcom,sc7180-smmu-500
               - qcom,sdm845-smmu-500
+              - qcom,sm8150-smmu-500
+              - qcom,sm8250-smmu-500
           - const: arm,mmu-500
       - items:
           - const: arm,mmu-500
Signature · 7 lines
2.26.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
maintainer Acked-by on v2 1/8
#2 lore raw

Re: [PATCH v2 1/8] dt-bindings: arm-smmu: Add sm8150 and sm8250 compatible strings

Quoted 7 lines · Jonathan Marek

Add compatible strings for sm8150 and sm8250 iommus to documentation.

---
 Documentation/devicetree/bindings/iommu/arm,smmu.yaml | 2 ++
 1 file changed, 2 insertions(+)

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu

#3 lore raw

PATCH v2 2/8 iommu: arm-smmu-impl: Use qcom impl for sm8150 and sm8250 compatibles

In reply to Jonathan Marek

Use the qcom implementation for IOMMU hardware on sm8150 and sm8250 SoCs.

---
 drivers/iommu/arm-smmu-impl.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/iommu/arm-smmu-impl.c +3 -1
index c75b9d957b70..f5f6cab626be 100644
@@ -172,7 +172,9 @@ struct arm_smmu_device *arm_smmu_impl_init(struct arm_smmu_device *smmu)
 		smmu->impl = &calxeda_impl;
 
 	if (of_device_is_compatible(np, "qcom,sdm845-smmu-500") ||
-	    of_device_is_compatible(np, "qcom,sc7180-smmu-500"))
+	    of_device_is_compatible(np, "qcom,sc7180-smmu-500") ||
+	    of_device_is_compatible(np, "qcom,sm8150-smmu-500") ||
+	    of_device_is_compatible(np, "qcom,sm8250-smmu-500"))
 		return qcom_smmu_impl_init(smmu);
 
 	return smmu;
Signature · 7 lines
2.26.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
reviewer
#4 lore raw

Re: [PATCH v2 2/8] iommu: arm-smmu-impl: Use qcom impl for sm8150 and sm8250 compatibles

Quoted 1 line · Jonathan Marek

Use the qcom implementation for IOMMU hardware on sm8150 and sm8250 SoCs.

Given a promise that anyone who wants to add more of these in future converts it into an of_device_id table exported from arm-smmu-qcom,

Reviewed-by Robin Murphy <[email protected]>

Quoted 21 lines
---
  drivers/iommu/arm-smmu-impl.c | 4 +++-
  1 file changed, 3 insertions(+), 1 deletion(-)
drivers/iommu/arm-smmu-impl.c +3 -1
index c75b9d957b70..f5f6cab626be 100644
@@ -172,7 +172,9 @@ struct arm_smmu_device *arm_smmu_impl_init(struct arm_smmu_device *smmu)
  		smmu->impl = &calxeda_impl;
 
  	if (of_device_is_compatible(np, "qcom,sdm845-smmu-500") ||
-	    of_device_is_compatible(np, "qcom,sc7180-smmu-500"))
+	    of_device_is_compatible(np, "qcom,sc7180-smmu-500") ||
+	    of_device_is_compatible(np, "qcom,sm8150-smmu-500") ||
+	    of_device_is_compatible(np, "qcom,sm8250-smmu-500"))
  		return qcom_smmu_impl_init(smmu);
 
  	return smmu;
Reviewed-by on v2 2/8
#5 lore raw

Re: [PATCH v2 2/8] iommu: arm-smmu-impl: Use qcom impl for sm8150 and sm8250 compatibles

In reply to Jonathan Marek
Quoted 3 lines · Jonathan Marek

Use the qcom implementation for IOMMU hardware on sm8150 and sm8250 SoCs.

Regards,
Bjorn

Quoted 27 lines
---
 drivers/iommu/arm-smmu-impl.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/iommu/arm-smmu-impl.c +3 -1
index c75b9d957b70..f5f6cab626be 100644
@@ -172,7 +172,9 @@ struct arm_smmu_device *arm_smmu_impl_init(struct arm_smmu_device *smmu)
 		smmu->impl = &calxeda_impl;
 
 	if (of_device_is_compatible(np, "qcom,sdm845-smmu-500") ||
-	    of_device_is_compatible(np, "qcom,sc7180-smmu-500"))
+	    of_device_is_compatible(np, "qcom,sc7180-smmu-500") ||
+	    of_device_is_compatible(np, "qcom,sm8150-smmu-500") ||
+	    of_device_is_compatible(np, "qcom,sm8250-smmu-500"))
 		return qcom_smmu_impl_init(smmu);
 
 	return smmu;
Signature · 7 lines
2.26.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#6 lore raw

PATCH v2 3/8 arm64: dts: qcom: sm8150: add apps_smmu node

In reply to Jonathan Marek

Add the apps_smmu node for sm8150.

For UFS, now that the kernel initializes the iommu, the stream mappings set by the bootloader are cleared. Adding the iommus property is required so that new mappings are created for UFS.

---
 arch/arm64/boot/dts/qcom/sm8150.dtsi | 91 ++++++++++++++++++++++++++++
 1 file changed, 91 insertions(+)
arch/arm64/boot/dts/qcom/sm8150.dtsi +91 -0
index a36512d1f6a1..5b48dbaee2d8 100644
@@ -442,6 +442,8 @@ ufs_mem_hc: ufshc@1d84000 {
 			resets = <&gcc GCC_UFS_PHY_BCR>;
 			reset-names = "rst";
 
+			iommus = <&apps_smmu 0x300 0>;
+
 			clock-names =
 				"core_clk",
 				"bus_aggr_clk",
@@ -706,6 +708,7 @@ usb_1_dwc3: dwc3@a600000 {
 				compatible = "snps,dwc3";
 				reg = <0 0x0a600000 0 0xcd00>;
 				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x140 0>;
 				snps,dis_u2_susphy_quirk;
 				snps,dis_enblslpm_quirk;
 				phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
@@ -742,6 +745,94 @@ spmi_bus: spmi@c440000 {
 			cell-index = <0>;
 		};
 
+		apps_smmu: iommu@15000000 {
+			compatible = "qcom,sm8150-smmu-500", "arm,mmu-500";
+			reg = <0 0x15000000 0 0x100000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <1>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		remoteproc_adsp: remoteproc@17300000 {
 			compatible = "qcom,sm8150-adsp-pas";
 			reg = <0x0 0x17300000 0x0 0x4040>;
Signature · 1 line
2.26.1
#7 lore raw

PATCH v2 4/8 arm64: dts: qcom: sm8250: add apps_smmu node

In reply to Jonathan Marek

Add the apps_smmu node for sm8250.

For UFS, now that the kernel initializes the iommu, the stream mappings set by the bootloader are cleared. Adding the iommus property is required so that new mappings are created for UFS.

---
 arch/arm64/boot/dts/qcom/sm8250.dtsi | 107 +++++++++++++++++++++++++++
 1 file changed, 107 insertions(+)
arch/arm64/boot/dts/qcom/sm8250.dtsi +107 -0
index 2f99c350c287..035f4552a0ff 100644
@@ -323,6 +323,8 @@ ufs_mem_hc: ufshc@1d84000 {
 
 			power-domains = <&gcc UFS_PHY_GDSC>;
 
+			iommus = <&apps_smmu 0x0e0 0>, <&apps_smmu 0x4e0 0>;
+
 			clock-names =
 				"core_clk",
 				"bus_aggr_clk",
@@ -428,6 +430,111 @@ tlmm: pinctrl@f100000 {
 			wakeup-parent = <&pdc>;
 		};
 
+		apps_smmu: iommu@15000000 {
+			compatible = "qcom,sm8250-smmu-500", "arm,mmu-500";
+			reg = <0 0x15000000 0 0x100000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <2>;
+			interrupts =    <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 690 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 691 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 692 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 693 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 694 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 695 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 696 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 697 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		intc: interrupt-controller@17a00000 {
 			compatible = "arm,gic-v3";
 			#interrupt-cells = <3>;
Signature · 1 line
2.26.1
#8 lore raw

PATCH v2 5/8 arm64: dts: qcom: sm8150: Add secondary USB and PHY nodes

In reply to Jonathan Marek

Add dts nodes for the secondary USB controller and related PHY nodes.

---
 arch/arm64/boot/dts/qcom/sm8150.dtsi | 89 ++++++++++++++++++++++++++++
 1 file changed, 89 insertions(+)
arch/arm64/boot/dts/qcom/sm8150.dtsi +89 -0
index 5b48dbaee2d8..f928ef9fa3a3 100644
@@ -636,6 +636,19 @@ usb_1_hsphy: phy@88e2000 {
 			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
 		};
 
+		usb_2_hsphy: phy@88e3000 {
+			compatible = "qcom,sm8150-usb-hs-phy",
+				     "qcom,usb-snps-hs-7nm-phy";
+			reg = <0 0x088e3000 0 0x400>;
+			status = "disabled";
+			#phy-cells = <0>;
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
+		};
+
 		usb_1_qmpphy: phy@88e9000 {
 			compatible = "qcom,sm8150-qmp-usb3-phy";
 			reg = <0 0x088e9000 0 0x18c>,
@@ -671,6 +684,37 @@ usb_1_ssphy: lanes@88e9200 {
 			};
 		};
 
+		usb_2_qmpphy: phy@88eb000 {
+			compatible = "qcom,sm8150-qmp-usb3-uni-phy";
+			reg = <0 0x088eb000 0 0x200>;
+			status = "disabled";
+			#clock-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_SEC_CLKREF_CLK>,
+				 <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
+			clock-names = "aux", "ref_clk_src", "ref", "com_aux";
+
+			resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
+				 <&gcc GCC_USB3_PHY_SEC_BCR>;
+			reset-names = "phy", "common";
+
+			usb_2_ssphy: lane@88eb200 {
+				reg = <0 0x088eb200 0 0x200>,
+				      <0 0x088eb400 0 0x200>,
+				      <0 0x088eb800 0 0x800>,
+				      <0 0x088eb600 0 0x200>;
+				#phy-cells = <0>;
+				clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb3_uni_phy_pipe_clk_src";
+			};
+		};
+
 		usb_1: usb@a6f8800 {
 			compatible = "qcom,sm8150-dwc3", "qcom,dwc3";
 			reg = <0 0x0a6f8800 0 0x400>;
@@ -716,6 +760,51 @@ usb_1_dwc3: dwc3@a600000 {
 			};
 		};
 
+		usb_2: usb@a8f8800 {
+			compatible = "qcom,sm8150-dwc3", "qcom,dwc3";
+			reg = <0 0x0a8f8800 0 0x400>;
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			dma-ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
+				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
+				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB30_SEC_SLEEP_CLK>,
+				 <&gcc GCC_USB3_SEC_CLKREF_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+				      "sleep", "xo";
+
+			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 487 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 490 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 491 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hs_phy_irq", "ss_phy_irq",
+					  "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+			power-domains = <&gcc USB30_SEC_GDSC>;
+
+			resets = <&gcc GCC_USB30_SEC_BCR>;
+
+			usb_2_dwc3: dwc3@a800000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a800000 0 0xcd00>;
+				interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x160 0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				phys = <&usb_2_hsphy>, <&usb_2_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
+
 		aoss_qmp: power-controller@c300000 {
 			compatible = "qcom,sm8150-aoss-qmp";
 			reg = <0x0 0x0c300000 0x0 0x100000>;
Signature · 1 line
2.26.1
#9 lore raw

PATCH v2 6/8 arm64: dts: qcom: sm8250: Add USB and PHY device nodes

In reply to Jonathan Marek

Add device nodes for the USB3 controller, QMP SS PHY and SNPS HS PHY.

---
 arch/arm64/boot/dts/qcom/sm8250.dtsi | 180 +++++++++++++++++++++++++++
 1 file changed, 180 insertions(+)
arch/arm64/boot/dts/qcom/sm8250.dtsi +180 -0
index 035f4552a0ff..25224d8cac4e 100644
@@ -387,6 +387,186 @@ tcsr_mutex: hwlock@1f40000 {
 			#hwlock-cells = <1>;
 		};
 
+		usb_1_hsphy: phy@88e3000 {
+			compatible = "qcom,sm8250-usb-hs-phy",
+				     "qcom,usb-snps-hs-7nm-phy";
+			reg = <0 0x088e3000 0 0x400>;
+			status = "disabled";
+			#phy-cells = <0>;
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+		};
+
+		usb_2_hsphy: phy@88e4000 {
+			compatible = "qcom,sm8250-usb-hs-phy",
+				     "qcom,usb-snps-hs-7nm-phy";
+			reg = <0 0x088e4000 0 0x400>;
+			status = "disabled";
+			#phy-cells = <0>;
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
+		};
+
+		usb_1_qmpphy: phy@88e9000 {
+			compatible = "qcom,sm8250-qmp-usb3-phy";
+			reg = <0 0x088e9000 0 0x200>,
+			      <0 0x088e8000 0 0x20>;
+			reg-names = "reg-base", "dp_com";
+			status = "disabled";
+			#clock-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
+			clock-names = "aux", "ref_clk_src", "com_aux";
+
+			resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
+				 <&gcc GCC_USB3_PHY_PRIM_BCR>;
+			reset-names = "phy", "common";
+
+			usb_1_ssphy: lanes@88e9200 {
+				reg = <0 0x088e9200 0 0x200>,
+				      <0 0x088e9400 0 0x200>,
+				      <0 0x088e9c00 0 0x400>,
+				      <0 0x088e9600 0 0x200>,
+				      <0 0x088e9800 0 0x200>,
+				      <0 0x088e9a00 0 0x100>;
+				#phy-cells = <0>;
+				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb3_phy_pipe_clk_src";
+			};
+		};
+
+		usb_2_qmpphy: phy@88eb000 {
+			compatible = "qcom,sm8250-qmp-usb3-uni-phy";
+			reg = <0 0x088eb000 0 0x200>;
+			status = "disabled";
+			#clock-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_SEC_CLKREF_EN>,
+				 <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
+			clock-names = "aux", "ref_clk_src", "ref", "com_aux";
+
+			resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
+				 <&gcc GCC_USB3_PHY_SEC_BCR>;
+			reset-names = "phy", "common";
+
+			usb_2_ssphy: lane@88eb200 {
+				reg = <0 0x088eb200 0 0x200>,
+				      <0 0x088eb400 0 0x200>,
+				      <0 0x088eb800 0 0x800>;
+				#phy-cells = <0>;
+				clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb3_uni_phy_pipe_clk_src";
+			};
+		};
+
+		usb_1: usb@a6f8800 {
+			compatible = "qcom,sm8250-dwc3", "qcom,dwc3";
+			reg = <0 0x0a6f8800 0 0x400>;
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			dma-ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB3_SEC_CLKREF_EN>;
+			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+				      "sleep", "xo";
+
+			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hs_phy_irq", "dp_hs_phy_irq",
+					  "dm_hs_phy_irq", "ss_phy_irq";
+
+			power-domains = <&gcc USB30_PRIM_GDSC>;
+
+			resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+			usb_1_dwc3: dwc3@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a600000 0 0xcd00>;
+				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x0 0x0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
+
+		usb_2: usb@a8f8800 {
+			compatible = "qcom,sm8250-dwc3", "qcom,dwc3";
+			reg = <0 0x0a8f8800 0 0x400>;
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			dma-ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
+				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
+				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB30_SEC_SLEEP_CLK>,
+				 <&gcc GCC_USB3_SEC_CLKREF_EN>;
+			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+				      "sleep", "xo";
+
+			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 12 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 13 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 16 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hs_phy_irq", "dp_hs_phy_irq",
+					  "dm_hs_phy_irq", "ss_phy_irq";
+
+			power-domains = <&gcc USB30_SEC_GDSC>;
+
+			resets = <&gcc GCC_USB30_SEC_BCR>;
+
+			usb_2_dwc3: dwc3@a800000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a800000 0 0xcd00>;
+				interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x20 0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				phys = <&usb_2_hsphy>, <&usb_2_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
+
 		pdc: interrupt-controller@b220000 {
 			compatible = "qcom,sm8250-pdc", "qcom,pdc";
 			reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
Signature · 1 line
2.26.1
#10 lore raw

PATCH v2 7/8 arm64: dts: qcom: add sm8150 hdk dts

In reply to Jonathan Marek

Add initial HDK855 dts, based on sm8150-mtp, with a few changes.

---
 arch/arm64/boot/dts/qcom/Makefile       |   1 +
 arch/arm64/boot/dts/qcom/sm8150-hdk.dts | 463 ++++++++++++++++++++++++
 2 files changed, 464 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm8150-hdk.dts
arch/arm64/boot/dts/qcom/Makefile +1 -0
index 0f2c33d611df..ad9d2c1a2f84 100644
@@ -23,6 +23,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-db845c.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm850-lenovo-yoga-c630.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-hdk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
arch/arm64/boot/dts/qcom/sm8150-hdk.dts new file +463 -0

463 lines not on this page · raw message

Signature · 1 line
2.26.1
#11 lore raw

PATCH v2 8/8 arm64: dts: qcom: add sm8250 hdk dts

In reply to Jonathan Marek

Add initial HDK865 dts, based on sm8250-mtp, with a few changes. Notably, regulator configs are changed a bit.

---
 arch/arm64/boot/dts/qcom/Makefile       |   1 +
 arch/arm64/boot/dts/qcom/sm8250-hdk.dts | 454 ++++++++++++++++++++++++
 2 files changed, 455 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm8250-hdk.dts
arch/arm64/boot/dts/qcom/Makefile +1 -0
index ad9d2c1a2f84..0ce50602e75a 100644
@@ -25,6 +25,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm850-lenovo-yoga-c630.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-hdk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-hdk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
arch/arm64/boot/dts/qcom/sm8250-hdk.dts new file +454 -0

454 lines not on this page · raw message

Signature · 1 line
2.26.1
maintainer
#12 lore raw
In reply to Jonathan Marek
Quoted 12 lines · Jonathan Marek

Add dts nodes for apps_smmu and USB for both sm8150 and sm8250.

Also add initial dts files for HDK855 and HDK865, based on mtp dts, with a few changes. Notably, the HDK865 dts has regulator config changed a bit based on downstream (I think sm8250-mtp.dts is wrong and copied too much from sm8150).

V2 changes:
* Added two patches for sm8150 and sm8250 iommu compatibles
* Changed apps_smmu node patches to use new compatibles
* Updated commit messages for apps_smmu patches to be more correct
* Updated HDK dts patches based on Bjorn's comments

Quoted 9 lines

Jonathan Marek (8):
dt-bindings: arm-smmu: Add sm8150 and sm8250 compatible strings
iommu: arm-smmu-impl: Use qcom impl for sm8150 and sm8250 compatibles
arm64: dts: qcom: sm8150: add apps_smmu node
arm64: dts: qcom: sm8250: add apps_smmu node
arm64: dts: qcom: sm8150: Add secondary USB and PHY nodes
arm64: dts: qcom: sm8250: Add USB and PHY device nodes
arm64: dts: qcom: add sm8150 hdk dts
arm64: dts: qcom: add sm8250 hdk dts

What's your plan for merging this? I can take the first two patches via arm-smmu, if you like. Please just let me know.

Will

#13 lore raw
Quoted 23 lines · Will Deacon
Quoted 12 lines · Jonathan Marek

Add dts nodes for apps_smmu and USB for both sm8150 and sm8250.

Also add initial dts files for HDK855 and HDK865, based on mtp dts, with a few changes. Notably, the HDK865 dts has regulator config changed a bit based on downstream (I think sm8250-mtp.dts is wrong and copied too much from sm8150).

V2 changes:
* Added two patches for sm8150 and sm8250 iommu compatibles
* Changed apps_smmu node patches to use new compatibles
* Updated commit messages for apps_smmu patches to be more correct
* Updated HDK dts patches based on Bjorn's comments

Quoted 9 lines

Jonathan Marek (8):
dt-bindings: arm-smmu: Add sm8150 and sm8250 compatible strings
iommu: arm-smmu-impl: Use qcom impl for sm8150 and sm8250 compatibles
arm64: dts: qcom: sm8150: add apps_smmu node
arm64: dts: qcom: sm8250: add apps_smmu node
arm64: dts: qcom: sm8150: Add secondary USB and PHY nodes
arm64: dts: qcom: sm8250: Add USB and PHY device nodes
arm64: dts: qcom: add sm8150 hdk dts
arm64: dts: qcom: add sm8250 hdk dts

Quoted 3 lines

What's your plan for merging this? I can take the first two patches via arm-smmu, if you like. Please just let me know.

Please pick up the binding and driver patch through your tree.

Regards,
Bjorn

maintainer Applied
#14 lore raw
In reply to Jonathan Marek
Quoted 6 lines · Jonathan Marek

Add dts nodes for apps_smmu and USB for both sm8150 and sm8250.

Also add initial dts files for HDK855 and HDK865, based on mtp dts, with a few changes. Notably, the HDK865 dts has regulator config changed a bit based on downstream (I think sm8250-mtp.dts is wrong and copied too much from sm8150).

Quoted 7 lines

V2 changes:
* Added two patches for sm8150 and sm8250 iommu compatibles
* Changed apps_smmu node patches to use new compatibles
* Updated commit messages for apps_smmu patches to be more correct
* Updated HDK dts patches based on Bjorn's comments

[...]

Applied to will (for-joerg/arm-smmu/updates), thanks!

[1/2] dt-bindings: arm-smmu: Add sm8150 and sm8250 compatible strings

      https://git.kernel.org/will/c/7b6b70d88b10
[2/2] iommu: arm-smmu-impl: Use qcom impl for sm8150 and sm8250 compatibles
      https://git.kernel.org/will/c/2c5c3cfb2da5

Cheers,

Signature · 5 lines
Will

https://fixes.arm64.dev
https://next.arm64.dev
https://will.arm64.dev