net: dc2114x: Use PCI_DEVICE() to define PCI device compat list
PATCH 1/12 net: dc2114x: Use PCI_DEVICE() to define PCI device compat list
Use this macro to fully fill the PCI device ID table. This is mandatory for the DM PCI support, which checks all the fields.
--- drivers/net/dc2114x.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/net/dc2114x.c +2 -2
@@ -568,8 +568,8 @@ static void read_hw_addr(struct eth_device *dev, bd_t *bis) }static struct pci_device_id supported[] = { - {PCI_VENDOR_ID_DEC ,PCI_DEVICE_ID_DEC_TULIP_FAST }, - {PCI_VENDOR_ID_DEC ,PCI_DEVICE_ID_DEC_21142 }, + {PCI_DEVICE (PCI_VENDOR_ID_DEC ,PCI_DEVICE_ID_DEC_TULIP_FAST ) }, + {PCI_DEVICE (PCI_VENDOR_ID_DEC ,PCI_DEVICE_ID_DEC_21142 ) }, { } };
Signature · 1 line
2.27.0
PATCH 2/12 net: dc2114x: Support all DC2114x
For the usage in this driver, the chips are identical, so support all of them.
--- drivers/net/dc2114x.c | 9 --------- 1 file changed, 9 deletions(-)
drivers/net/dc2114x.c +0 -9
@@ -581,7 +581,6 @@ int dc21x4x_initialize(bd_t *bis)unsigned int iobase;int card_number =0 ;pci_dev_t devbusfn; -unsigned int cfrv;int idx =0 ;while (1 ) {
@@ -589,14 +588,6 @@ int dc21x4x_initialize(bd_t *bis)if (devbusfn ==-1 )break ; -/* Get the chip configuration revision register. */ -pci_read_config_dword (devbusfn,PCI_REVISION_ID , &cfrv); - -if ((cfrv &CFRV_RN ) < DC2114x_BRK) { -printf ("Error: The chip is not DC21143.\n" ); -continue ; - } -pci_read_config_word (devbusfn,PCI_COMMAND , &status); status |=PCI_COMMAND_MEMORY |PCI_COMMAND_MASTER ;pci_write_config_word (devbusfn,PCI_COMMAND , status);
Signature · 1 line
2.27.0
PATCH 3/12 net: dc2114x: Add Kconfig entries
In reply to Marek VasutAdd Kconfig entries for the dc2114x driver and convert various boards.
--- README | 3 --- configs/integratorap_cm720t_defconfig | 1 + configs/integratorap_cm920t_defconfig | 1 + configs/integratorap_cm926ejs_defconfig | 1 + configs/integratorap_cm946es_defconfig | 1 + drivers/net/Kconfig | 6 ++++++ include/configs/MPC8349EMDS.h | 1 - include/configs/MPC8349EMDS_SDRAM.h | 1 - include/configs/MPC8540ADS.h | 1 - include/configs/MPC8541CDS.h | 1 - include/configs/MPC8544DS.h | 1 - include/configs/MPC8548CDS.h | 1 - include/configs/MPC8555CDS.h | 1 - include/configs/MPC8560ADS.h | 1 - include/configs/MPC8568MDS.h | 1 - include/configs/MPC8569MDS.h | 1 - include/configs/MPC8572DS.h | 1 - include/configs/MPC8641HPCN.h | 1 - include/configs/TQM834x.h | 1 - include/configs/caddy2.h | 1 - include/configs/integratorap.h | 1 - include/configs/sbc8349.h | 1 - include/configs/sbc8548.h | 1 - include/configs/sbc8641d.h | 1 - include/configs/vme8349.h | 1 - scripts/config_whitelist.txt | 1 - 26 files changed, 10 insertions(+), 23 deletions(-)
README +0 -3
@@ -871,9 +871,6 @@ The following options need to be configured: Allow generic access to the SPI bus on the Intel 8257x, for example with the "sspi" command. - CONFIG_TULIP - Support for Digital 2114x chips. - CONFIG_NATSEMI Support for National dp83815 chips.
configs/integratorap_cm720t_defconfig +1 -0
@@ -25,6 +25,7 @@ CONFIG_FLASH_CFI_DRIVER=y CONFIG_SYS_FLASH_PROTECTION=y CONFIG_SYS_FLASH_CFI=y CONFIG_EEPRO100=y +CONFIG_TULIP=y CONFIG_PCI=y CONFIG_BAUDRATE=38400 CONFIG_OF_LIBFDT=y
configs/integratorap_cm920t_defconfig +1 -0
@@ -25,6 +25,7 @@ CONFIG_FLASH_CFI_DRIVER=y CONFIG_SYS_FLASH_PROTECTION=y CONFIG_SYS_FLASH_CFI=y CONFIG_EEPRO100=y +CONFIG_TULIP=y CONFIG_PCI=y CONFIG_BAUDRATE=38400 CONFIG_OF_LIBFDT=y
configs/integratorap_cm926ejs_defconfig +1 -0
@@ -25,6 +25,7 @@ CONFIG_FLASH_CFI_DRIVER=y CONFIG_SYS_FLASH_PROTECTION=y CONFIG_SYS_FLASH_CFI=y CONFIG_EEPRO100=y +CONFIG_TULIP=y CONFIG_PCI=y CONFIG_BAUDRATE=38400 CONFIG_OF_LIBFDT=y
configs/integratorap_cm946es_defconfig +1 -0
@@ -25,6 +25,7 @@ CONFIG_FLASH_CFI_DRIVER=y CONFIG_SYS_FLASH_PROTECTION=y CONFIG_SYS_FLASH_CFI=y CONFIG_EEPRO100=y +CONFIG_TULIP=y CONFIG_PCI=y CONFIG_BAUDRATE=38400 CONFIG_OF_LIBFDT=y
drivers/net/Kconfig +6 -0
@@ -491,6 +491,12 @@ config SH_ETHER source "drivers/net/ti/Kconfig" +config TULIP + bool "DEC Tulip DC2114x Ethernet support" + depends on (DM_ETH && DM_PCI) || !DM_ETH + help + This driver supports DEC DC2114x Fast ethernet chips. + config XILINX_AXIEMAC depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP) select PHYLIB
include/configs/MPC8349EMDS.h +0 -1
@@ -220,7 +220,6 @@#define CONFIG_83XX_PCI_STREAMING -#undef CONFIG_TULIP#if !defined(CONFIG_PCI_PNP )#define PCI_ENET0_IOADDR 0xFIXME
include/configs/MPC8349EMDS_SDRAM.h +0 -1
@@ -275,7 +275,6 @@#define CONFIG_83XX_PCI_STREAMING -#undef CONFIG_TULIP#if !defined(CONFIG_PCI_PNP )#define PCI_ENET0_IOADDR 0xFIXME
include/configs/MPC8540ADS.h +0 -1
@@ -234,7 +234,6 @@#define CONFIG_SYS_PCI1_IO_SIZE 0x100000/* 1M */ #if defined(CONFIG_PCI ) -#undef CONFIG_TULIP#if !defined(CONFIG_PCI_PNP )#define PCI_ENET0_IOADDR 0xe0000000
include/configs/MPC8541CDS.h +0 -1
@@ -280,7 +280,6 @@ extern unsigned long get_clock_freq(void);#define CONFIG_MPC85XX_PCI2 -#undef CONFIG_TULIP#undef CONFIG_PCI_SCAN_SHOW/* show pci devices on startup */ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057/* Motorola */
include/configs/MPC8544DS.h +0 -1
@@ -256,7 +256,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET#endif -#undef CONFIG_TULIP#ifndef CONFIG_PCI_PNP #define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BUS
include/configs/MPC8548CDS.h +0 -1
@@ -379,7 +379,6 @@ extern unsigned long get_clock_freq(void);#endif #if defined(CONFIG_PCI ) -#undef CONFIG_TULIP#if !defined(CONFIG_DM_PCI )#define CONFIG_FSL_PCI_INIT 1/* Use common FSL init code */
include/configs/MPC8555CDS.h +0 -1
@@ -278,7 +278,6 @@ extern unsigned long get_clock_freq(void);#define CONFIG_MPC85XX_PCI2 -#undef CONFIG_TULIP#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057/* Motorola */
include/configs/MPC8560ADS.h +0 -1
@@ -231,7 +231,6 @@#define CONFIG_SYS_PCI1_IO_SIZE 0x100000/* 1M */ #if defined(CONFIG_PCI ) -#undef CONFIG_TULIP#if !defined(CONFIG_PCI_PNP )#define PCI_ENET0_IOADDR 0xe0000000
include/configs/MPC8568MDS.h +0 -1
@@ -288,7 +288,6 @@ extern unsigned long get_clock_freq(void);#endif /* CONFIG_QE */ #if defined(CONFIG_PCI ) -#undef CONFIG_TULIP#undef CONFIG_PCI_SCAN_SHOW/* show pci devices on startup */ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057/* Motorola */
include/configs/MPC8569MDS.h +0 -1
@@ -394,7 +394,6 @@ extern unsigned long get_clock_freq(void);#endif /* CONFIG_QE */ #if defined(CONFIG_PCI ) -#undef CONFIG_TULIP#undef CONFIG_PCI_SCAN_SHOW/* show pci devices on startup */
include/configs/MPC8572DS.h +0 -1
@@ -441,7 +441,6 @@#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET#endif -#undef CONFIG_TULIP#ifndef CONFIG_PCI_PNP #define PCI_ENET0_IOADDR CONFIG_SYS_PCIE3_IO_BUS
include/configs/MPC8641HPCN.h +0 -1
@@ -332,7 +332,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#undef CONFIG_TULIP/************************************************************ * USB support
include/configs/TQM834x.h +0 -1
@@ -167,7 +167,6 @@#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE#define CONFIG_SYS_PCI1_IO_SIZE 0x1000000/* 16M */ -#undef CONFIG_TULIP#if !defined(CONFIG_PCI_PNP )#define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BASE
include/configs/caddy2.h +0 -1
@@ -155,7 +155,6 @@#if defined(CONFIG_PCI ) -#undef CONFIG_TULIP#if !defined(CONFIG_PCI_PNP )#define PCI_ENET0_IOADDR 0xFIXME
include/configs/integratorap.h +0 -1
@@ -34,7 +34,6 @@* PCI definitions */ -#define CONFIG_TULIP #define CONFIG_SYS_RX_ETH_BUFFER 8/* use 8 rx buffer on eepro100 */ /*-----------------------------------------------------------------------
include/configs/sbc8349.h +0 -1
@@ -180,7 +180,6 @@#if defined(CONFIG_PCI ) -#undef CONFIG_TULIP#if !defined(CONFIG_PCI_PNP )#define PCI_ENET0_IOADDR 0xFIXME
include/configs/sbc8548.h +0 -1
@@ -432,7 +432,6 @@#endif #if defined(CONFIG_PCI ) -#undef CONFIG_TULIP#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
include/configs/sbc8641d.h +0 -1
@@ -274,7 +274,6 @@#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#undef CONFIG_TULIP#if !defined(CONFIG_PCI_PNP )#define PCI_ENET0_IOADDR 0xe0000000
include/configs/vme8349.h +0 -1
@@ -155,7 +155,6 @@#if defined(CONFIG_PCI ) -#undef CONFIG_TULIP#if !defined(CONFIG_PCI_PNP )#define PCI_ENET0_IOADDR 0xFIXME
scripts/config_whitelist.txt +0 -1
@@ -4032,7 +4032,6 @@ CONFIG_TSECV2 CONFIG_TSECV2_1 CONFIG_TSEC_TBI CONFIG_TSEC_TBICR_SETTINGS -CONFIG_TULIP CONFIG_TWL6030_INPUT CONFIG_TWL6030_POWER CONFIG_TWR
Signature · 1 line
2.27.0
PATCH 4/12 net: dc2114x: Drop update_srom()
In reply to Marek VasutThis code is never used, remove it.
--- drivers/net/dc2114x.c | 91 ------------------------------------------- 1 file changed, 91 deletions(-)
drivers/net/dc2114x.c +0 -91
@@ -11,8 +11,6 @@#define SROM_DLEVEL 0 -#undef UPDATE_SROM -/* PCI Registers. */ #define PCI_CFDA_PSM 0x43
@@ -270,92 +268,6 @@ static int read_srom(struct eth_device *dev, u_long ioaddr, int index) 3 + ee_addr_size + 16); } -#ifdef UPDATE_SROM -static int write_srom (struct eth_device *dev,u_long ioaddr,int index, -int new_value) -{ -unsigned short newval; -int ee_addr_size; -int i; - - ee_addr_size = (do_read_eeprom (dev, ioaddr,0xff ,8 ) &BIT (18 )) ?8 :6 ; - -udelay (10 *1000 );/* test-only */ - -debug_cond (SROM_DLEVEL >=1 ,"ee_addr_size=%d.\n" , ee_addr_size); -debug_cond (SROM_DLEVEL >=1 , -"Writing new entry 0x%4.4x to offset %d.\n" , - new_value, index); - -/* Enable programming modes. */ -do_eeprom_cmd (dev, ioaddr,0x4f << (ee_addr_size -4 ), -3 + ee_addr_size); - -/* Do the actual write. */ -do_eeprom_cmd (dev, ioaddr, new_value | - (((SROM_WRITE_CMD << ee_addr_size) | index) <<16 ), -3 + ee_addr_size +16 ); - -/* Poll for write finished. */ -sendto_srom (dev,SROM_RD |SROM_SR |DT_CS , ioaddr); -for (i =0 ; i <10000 ; i++) {/* Typical 2000 ticks */ -if (getfrom_srom (dev, ioaddr) &EE_DATA_READ ) -break ; - } - -debug_cond (SROM_DLEVEL >=1 ," Write finished after %d ticks.\n" , i); - -/* Disable programming. */ -do_eeprom_cmd (dev, ioaddr, (0x40 << (ee_addr_size -4 )), -3 + ee_addr_size); - -/* And read the result. */ - newval =do_eeprom_cmd (dev, ioaddr, - (((SROM_READ_CMD << ee_addr_size) | index) <<16 ) - |0xffff ,3 + ee_addr_size +16 ); - -debug_cond (SROM_DLEVEL >=1 ," New value at offset %d is %4.4x.\n" , - index, newval); - -return 1 ; -} - -static void update_srom (struct eth_device *dev,bd_t *bis) -{ -static unsigned short eeprom[0x40 ] = { -0x140b ,0x6610 ,0x0000 ,0x0000 ,/* 00 */ -0x0000 ,0x0000 ,0x0000 ,0x0000 ,/* 04 */ -0x00a3 ,0x0103 ,0x0000 ,0x0000 ,/* 08 */ -0x0000 ,0x1f00 ,0x0000 ,0x0000 ,/* 0c */ -0x0108 ,0x038d ,0x0000 ,0x0000 ,/* 10 */ -0xe078 ,0x0001 ,0x0040 ,0x0018 ,/* 14 */ -0x0000 ,0x0000 ,0x0000 ,0x0000 ,/* 18 */ -0x0000 ,0x0000 ,0x0000 ,0x0000 ,/* 1c */ -0x0000 ,0x0000 ,0x0000 ,0x0000 ,/* 20 */ -0x0000 ,0x0000 ,0x0000 ,0x0000 ,/* 24 */ -0x0000 ,0x0000 ,0x0000 ,0x0000 ,/* 28 */ -0x0000 ,0x0000 ,0x0000 ,0x0000 ,/* 2c */ -0x0000 ,0x0000 ,0x0000 ,0x0000 ,/* 30 */ -0x0000 ,0x0000 ,0x0000 ,0x0000 ,/* 34 */ -0x0000 ,0x0000 ,0x0000 ,0x0000 ,/* 38 */ -0x0000 ,0x0000 ,0x0000 ,0x4e07 ,/* 3c */ - }; -uchar enetaddr[6 ]; -int i; - -/* Ethernet Addr... */ -if (!eth_env_get_enetaddr ("ethaddr" , enetaddr)) -return ; - - eeprom[0x0a ] = (enetaddr[1 ] <<8 ) | enetaddr[0 ]; - eeprom[0x0b ] = (enetaddr[3 ] <<8 ) | enetaddr[2 ]; - eeprom[0x0c ] = (enetaddr[5 ] <<8 ) | enetaddr[4 ]; - -for (i =0 ; i <0x40 ; i++) -write_srom (dev,DE4X5_APROM , i, eeprom[i]); -} -#endif /* UPDATE_SROM */ -static void send_setup_frame (struct eth_device *dev,bd_t *bis) {char setup_frame[SETUP_FRAME_LEN ];
@@ -561,9 +473,6 @@ static void read_hw_addr(struct eth_device *dev, bd_t *bis)if (!j || j ==0x2fffd ) {memset (dev->enetaddr,0 ,ETH_ALEN );debug ("Warning: can't read HW address from SROM.\n" ); -#ifdef UPDATE_SROM -update_srom (dev, bis); -#endif } }
Signature · 1 line
2.27.0
PATCH 5/12 net: dc2114x: Use standard I/O accessors
In reply to Marek VasutThe current dc21x4x driver accesses its memory mapped registers directly instead of using the standard I/O accessors. This can cause problems on some systems as the accesses can get out of order. So convert the direct volatile dereferences to use the normal in/out macros.
--- drivers/net/dc2114x.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/net/dc2114x.c +3 -2
@@ -1,6 +1,7 @@// SPDX-License-Identifier: GPL-2.0+ #include <common.h> +#include <asm/io.h> #include <env.h> #include <malloc.h> #include <net.h>
@@ -104,12 +105,12 @@ static char tx_ring_size;static u32 dc2114x_inl (struct eth_device *dev,u32 addr) { -return le32_to_cpu (*(volatile u32 *)(addr + dev->iobase)); +return le32_to_cpu (readl (dev->iobase + addr)); }static void dc2114x_outl (struct eth_device *dev,u32 command,u32 addr) { - *(volatile u32 *)(addr + dev->iobase) =cpu_to_le32 (command); +writel (cpu_to_le32 (command), dev->iobase + addr); }static void reset_de4x5 (struct eth_device *dev)
Signature · 1 line
2.27.0
PATCH 6/12 net: dc2114x: Introduce private data
In reply to Marek VasutIntroduce dc2114x_priv, which is a super-structure around eth_device and tracks per-device state and the device IO address.
--- drivers/net/dc2114x.c | 25 ++++++++++++++++++------- 1 file changed, 18 insertions(+), 7 deletions(-)
drivers/net/dc2114x.c +18 -7
@@ -94,6 +94,13 @@ struct de4x5_desc {u32 next; }; +struct dc2114x_priv { +struct eth_device dev; +char *name; +void __iomem *iobase; +u8 *enetaddr; +}; +/* RX and TX descriptor ring */ static struct de4x5_desc rx_ring[NUM_RX_DESC ]__aligned(32) ;static struct de4x5_desc tx_ring[NUM_TX_DESC ]__aligned(32) ;
@@ -460,9 +467,9 @@ static void dc21x4x_halt(struct eth_device *dev)pci_write_config_byte (devbusfn,PCI_CFDA_PSM ,SLEEP ); } -static void read_hw_addr (struct eth_device *dev,bd_t *bis) +static void read_hw_addr (struct dc2114x_priv *priv) { -u_short tmp, *p = (u_short *)(&dev->enetaddr[0 ]); +u_short tmp, *p = (u_short *)(&priv->enetaddr[0 ]);int i, j =0 ;for (i =0 ; i < (ETH_ALEN >>1 ); i++) {
@@ -472,7 +479,7 @@ static void read_hw_addr(struct eth_device *dev, bd_t *bis) }if (!j || j ==0x2fffd ) { -memset (dev->enetaddr,0 ,ETH_ALEN ); +memset (priv->enetaddr,0 ,ETH_ALEN );debug ("Warning: can't read HW address from SROM.\n" ); } }
@@ -485,6 +492,7 @@ static struct pci_device_id supported[] = {int dc21x4x_initialize (bd_t *bis) { +struct dc2114x_priv *priv;struct eth_device *dev;unsigned short status;unsigned char timer;
@@ -526,15 +534,18 @@ int dc21x4x_initialize(bd_t *bis) iobase &=PCI_BASE_ADDRESS_MEM_MASK ;debug ("dc21x4x: DEC 21142 PCI Device @0x%x\n" , iobase); - dev = (struct eth_device *)malloc (sizeof (*dev)); -if (!dev) { + priv =malloc (sizeof (*priv)); +if (!priv) {printf ("Can not allocalte memory of dc21x4x\n" );break ; } +memset (priv,0 ,sizeof (*priv)); -memset (dev,0 ,sizeof (*dev)); + dev = &priv->dev;sprintf (dev->name,"dc21x4x#%d" , card_number); + priv->name = dev->name; + priv->enetaddr = dev->enetaddr; dev->iobase =pci_mem_to_phys (devbusfn, iobase); dev->priv = (void *)devbusfn;
@@ -548,7 +559,7 @@ int dc21x4x_initialize(bd_t *bis)udelay (10 *1000 ); -read_hw_addr (dev, bis); +read_hw_addr (priv);eth_register (dev);
Signature · 1 line
2.27.0
PATCH 7/12 net: dc2114x: Pass private data around
In reply to Marek VasutThis patch replaces the various uses of struct eth_device for accessing device private data with struct dc2114x_priv, which is compatible both with DM and non-DM operation.
--- drivers/net/dc2114x.c | 135 ++++++++++++++++++++++-------------------- 1 file changed, 71 insertions(+), 64 deletions(-)
drivers/net/dc2114x.c +71 -64
@@ -110,78 +110,78 @@ static int tx_new; /* TX descriptor ring pointer */static char rx_ring_size;static char tx_ring_size; -static u32 dc2114x_inl (struct eth_device *dev,u32 addr) +static u32 dc2114x_inl (struct dc2114x_priv *priv,u32 addr) { -return le32_to_cpu (readl (dev->iobase + addr)); +return le32_to_cpu (readl (priv->iobase + addr)); } -static void dc2114x_outl (struct eth_device *dev,u32 command,u32 addr) +static void dc2114x_outl (struct dc2114x_priv *priv,u32 command,u32 addr) { -writel (cpu_to_le32 (command), dev->iobase + addr); +writel (cpu_to_le32 (command), priv->iobase + addr); } -static void reset_de4x5 (struct eth_device *dev) +static void reset_de4x5 (struct dc2114x_priv *priv) {u32 i; - i =dc2114x_inl (dev,DE4X5_BMR ); + i =dc2114x_inl (priv,DE4X5_BMR );mdelay (1 ); -dc2114x_outl (dev, i |BMR_SWR ,DE4X5_BMR ); +dc2114x_outl (priv, i |BMR_SWR ,DE4X5_BMR );mdelay (1 ); -dc2114x_outl (dev, i,DE4X5_BMR ); +dc2114x_outl (priv, i,DE4X5_BMR );mdelay (1 );for (i =0 ; i <5 ; i++) { -dc2114x_inl (dev,DE4X5_BMR ); +dc2114x_inl (priv,DE4X5_BMR );mdelay (10 ); }mdelay (1 ); } -static void start_de4x5 (struct eth_device *dev) +static void start_de4x5 (struct dc2114x_priv *priv) {u32 omr; - omr =dc2114x_inl (dev,DE4X5_OMR ); + omr =dc2114x_inl (priv,DE4X5_OMR ); omr |=OMR_ST |OMR_SR ; -dc2114x_outl (dev, omr,DE4X5_OMR );/* Enable the TX and/or RX */ +dc2114x_outl (priv, omr,DE4X5_OMR );/* Enable the TX and/or RX */ } -static void stop_de4x5 (struct eth_device *dev) +static void stop_de4x5 (struct dc2114x_priv *priv) {u32 omr; - omr =dc2114x_inl (dev,DE4X5_OMR ); + omr =dc2114x_inl (priv,DE4X5_OMR ); omr &= ~(OMR_ST |OMR_SR ); -dc2114x_outl (dev, omr,DE4X5_OMR );/* Disable the TX and/or RX */ +dc2114x_outl (priv, omr,DE4X5_OMR );/* Disable the TX and/or RX */ }/* SROM Read and write routines. */ -static void sendto_srom (struct eth_device *dev,u_int command,u_long addr) +static void sendto_srom (struct dc2114x_priv *priv,u_int command,u_long addr) { -dc2114x_outl (dev, command, addr); +dc2114x_outl (priv, command, addr);udelay (1 ); } -static int getfrom_srom (struct eth_device *dev,u_long addr) +static int getfrom_srom (struct dc2114x_priv *priv,u_long addr) { -u32 tmp =dc2114x_inl (dev, addr); +u32 tmp =dc2114x_inl (priv, addr);udelay (1 );return tmp; }/* Note: this routine returns extra data bits for size detection. */ -static int do_read_eeprom (struct eth_device *dev,u_long ioaddr,int location, +static int do_read_eeprom (struct dc2114x_priv *priv,u_long ioaddr,int location,int addr_len) {int read_cmd = location | (SROM_READ_CMD << addr_len);unsigned int retval =0 ;int i; -sendto_srom (dev,SROM_RD |SROM_SR , ioaddr); -sendto_srom (dev,SROM_RD |SROM_SR |DT_CS , ioaddr); +sendto_srom (priv,SROM_RD |SROM_SR , ioaddr); +sendto_srom (priv,SROM_RD |SROM_SR |DT_CS , ioaddr);debug_cond (SROM_DLEVEL >=1 ," EEPROM read at %d " , location);
@@ -189,35 +189,35 @@ static int do_read_eeprom(struct eth_device *dev, u_long ioaddr, int location,for (i =4 + addr_len; i >=0 ; i--) {short dataval = (read_cmd & (1 << i)) ?EE_DATA_WRITE :0 ; -sendto_srom (dev,SROM_RD |SROM_SR |DT_CS | dataval, +sendto_srom (priv,SROM_RD |SROM_SR |DT_CS | dataval, ioaddr);udelay (10 ); -sendto_srom (dev,SROM_RD |SROM_SR |DT_CS | dataval |DT_CLK , +sendto_srom (priv,SROM_RD |SROM_SR |DT_CS | dataval |DT_CLK , ioaddr);udelay (10 );debug_cond (SROM_DLEVEL >=2 ,"%X" , -getfrom_srom (dev, ioaddr) &15 ); +getfrom_srom (priv, ioaddr) &15 ); retval = (retval <<1 ) | - !!(getfrom_srom (dev, ioaddr) &EE_DATA_READ ); + !!(getfrom_srom (priv, ioaddr) &EE_DATA_READ ); } -sendto_srom (dev,SROM_RD |SROM_SR |DT_CS , ioaddr); +sendto_srom (priv,SROM_RD |SROM_SR |DT_CS , ioaddr); -debug_cond (SROM_DLEVEL >=2 ," :%X:" ,getfrom_srom (dev, ioaddr) &15 ); +debug_cond (SROM_DLEVEL >=2 ," :%X:" ,getfrom_srom (priv, ioaddr) &15 );for (i =16 ; i >0 ; i--) { -sendto_srom (dev,SROM_RD |SROM_SR |DT_CS |DT_CLK , ioaddr); +sendto_srom (priv,SROM_RD |SROM_SR |DT_CS |DT_CLK , ioaddr);udelay (10 );debug_cond (SROM_DLEVEL >=2 ,"%X" , -getfrom_srom (dev, ioaddr) &15 ); +getfrom_srom (priv, ioaddr) &15 ); retval = (retval <<1 ) | - !!(getfrom_srom (dev, ioaddr) &EE_DATA_READ ); -sendto_srom (dev,SROM_RD |SROM_SR |DT_CS , ioaddr); + !!(getfrom_srom (priv, ioaddr) &EE_DATA_READ ); +sendto_srom (priv,SROM_RD |SROM_SR |DT_CS , ioaddr);udelay (10 ); }/* Terminate the EEPROM access. */ -sendto_srom (dev,SROM_RD |SROM_SR , ioaddr); +sendto_srom (priv,SROM_RD |SROM_SR , ioaddr);debug_cond (SROM_DLEVEL >=2 ," EEPROM value at %d is %5.5x.\n" , location, retval);
@@ -230,54 +230,55 @@ static int do_read_eeprom(struct eth_device *dev, u_long ioaddr, int location,* enable. It returns the data output from the EEPROM, and thus may * also be used for reads. */ -static int do_eeprom_cmd (struct eth_device *dev,u_long ioaddr,int cmd, +static int do_eeprom_cmd (struct dc2114x_priv *priv,u_long ioaddr,int cmd,int cmd_len) {unsigned int retval =0 ;debug_cond (SROM_DLEVEL >=1 ," EEPROM op 0x%x: " , cmd); -sendto_srom (dev,SROM_RD |SROM_SR |DT_CS |DT_CLK , ioaddr); +sendto_srom (priv,SROM_RD |SROM_SR |DT_CS |DT_CLK , ioaddr);/* Shift the command bits out. */ do {short dataval = (cmd &BIT (cmd_len)) ?EE_WRITE_1 :EE_WRITE_0 ; -sendto_srom (dev, dataval, ioaddr); +sendto_srom (priv, dataval, ioaddr);udelay (10 );debug_cond (SROM_DLEVEL >=2 ,"%X" , -getfrom_srom (dev, ioaddr) &15 ); +getfrom_srom (priv, ioaddr) &15 ); -sendto_srom (dev, dataval |DT_CLK , ioaddr); +sendto_srom (priv, dataval |DT_CLK , ioaddr);udelay (10 ); retval = (retval <<1 ) | - !!(getfrom_srom (dev, ioaddr) &EE_DATA_READ ); + !!(getfrom_srom (priv, ioaddr) &EE_DATA_READ ); }while (--cmd_len >=0 ); -sendto_srom (dev,SROM_RD |SROM_SR |DT_CS , ioaddr); +sendto_srom (priv,SROM_RD |SROM_SR |DT_CS , ioaddr);/* Terminate the EEPROM access. */ -sendto_srom (dev,SROM_RD |SROM_SR , ioaddr); +sendto_srom (priv,SROM_RD |SROM_SR , ioaddr);debug_cond (SROM_DLEVEL >=1 ," EEPROM result is 0x%5.5x.\n" , retval);return retval; } -static int read_srom (struct eth_device *dev,u_long ioaddr,int index) +static int read_srom (struct dc2114x_priv *priv,u_long ioaddr,int index) {int ee_addr_size; - ee_addr_size = (do_read_eeprom (dev, ioaddr,0xff ,8 ) &BIT (18 )) ?8 :6 ; + ee_addr_size = (do_read_eeprom (priv, ioaddr,0xff ,8 ) &BIT (18 )) ?8 :6 ; -return do_eeprom_cmd (dev, ioaddr,0xffff | +return do_eeprom_cmd (priv, ioaddr,0xffff | (((SROM_READ_CMD << ee_addr_size) | index) <<16 ),3 + ee_addr_size +16 ); } -static void send_setup_frame (struct eth_device *dev,bd_t *bis) +static void send_setup_frame (struct dc2114x_priv *priv,bd_t *bis) { +struct eth_device *dev = &priv->dev;char setup_frame[SETUP_FRAME_LEN ];char *pa = &setup_frame[0 ];int i;
@@ -285,7 +286,7 @@ static void send_setup_frame(struct eth_device *dev, bd_t *bis)memset (pa,0xff ,SETUP_FRAME_LEN );for (i =0 ; i <ETH_ALEN ; i++) { - *(pa + (i &1 )) = dev->enetaddr[i]; + *(pa + (i &1 )) = priv->enetaddr[i];if (i &0x01 ) pa +=4 ; }
@@ -294,7 +295,7 @@ static void send_setup_frame(struct eth_device *dev, bd_t *bis)if (i <TOUT_LOOP )continue ; -printf ("%s: tx error buffer not ready\n" , dev->name); +printf ("%s: tx error buffer not ready\n" , priv->name);return ; }
@@ -302,13 +303,13 @@ static void send_setup_frame(struct eth_device *dev, bd_t *bis) tx_ring[tx_new].des1 =cpu_to_le32 (TD_TER |TD_SET |SETUP_FRAME_LEN ); tx_ring[tx_new].status =cpu_to_le32 (T_OWN ); -dc2114x_outl (dev,POLL_DEMAND ,DE4X5_TPD ); +dc2114x_outl (priv,POLL_DEMAND ,DE4X5_TPD );for (i =0 ; tx_ring[tx_new].status &cpu_to_le32 (T_OWN ); i++) {if (i <TOUT_LOOP )continue ; -printf ("%s: tx buffer not ready\n" , dev->name); +printf ("%s: tx buffer not ready\n" , priv->name);return ; }
@@ -322,11 +323,13 @@ static void send_setup_frame(struct eth_device *dev, bd_t *bis)static int dc21x4x_send (struct eth_device *dev,void *packet,int length) { +struct dc2114x_priv *priv = + container_of(dev, struct dc2114x_priv, dev);int status =-1 ;int i;if (length <=0 ) { -printf ("%s: bad packet size: %d\n" , dev->name, length); +printf ("%s: bad packet size: %d\n" , priv->name, length); goto done; }
@@ -334,7 +337,7 @@ static int dc21x4x_send(struct eth_device *dev, void *packet, int length)if (i <TOUT_LOOP )continue ; -printf ("%s: tx error buffer not ready\n" , dev->name); +printf ("%s: tx error buffer not ready\n" , priv->name); goto done; }
@@ -342,13 +345,13 @@ static int dc21x4x_send(struct eth_device *dev, void *packet, int length) tx_ring[tx_new].des1 =cpu_to_le32 (TD_TER |TD_LS |TD_FS | length); tx_ring[tx_new].status =cpu_to_le32 (T_OWN ); -dc2114x_outl (dev,POLL_DEMAND ,DE4X5_TPD ); +dc2114x_outl (priv,POLL_DEMAND ,DE4X5_TPD );for (i =0 ; tx_ring[tx_new].status &cpu_to_le32 (T_OWN ); i++) {if (i <TOUT_LOOP )continue ; -printf (".%s: tx buffer not ready\n" , dev->name); +printf (".%s: tx buffer not ready\n" , priv->name); goto done; }
@@ -406,20 +409,22 @@ static int dc21x4x_recv(struct eth_device *dev)static int dc21x4x_init (struct eth_device *dev,bd_t *bis) { -int i; +struct dc2114x_priv *priv = + container_of(dev, struct dc2114x_priv, dev);int devbusfn = (int )dev->priv; +int i;/* Ensure we're not sleeping. */ pci_write_config_byte (devbusfn,PCI_CFDA_PSM ,WAKEUP ); -reset_de4x5 (dev); +reset_de4x5 (priv); -if (dc2114x_inl (dev,DE4X5_STS ) & (STS_TS |STS_RS )) { +if (dc2114x_inl (priv,DE4X5_STS ) & (STS_TS |STS_RS )) {printf ("Error: Cannot reset ethernet controller.\n" );return -1 ; } -dc2114x_outl (dev,OMR_SDP |OMR_PS |OMR_PM ,DE4X5_OMR ); +dc2114x_outl (priv,OMR_SDP |OMR_PS |OMR_PM ,DE4X5_OMR );for (i =0 ; i <NUM_RX_DESC ; i++) { rx_ring[i].status =cpu_to_le32 (R_OWN );
@@ -444,25 +449,27 @@ static int dc21x4x_init(struct eth_device *dev, bd_t *bis) tx_ring[tx_ring_size -1 ].des1 |=cpu_to_le32 (TD_TER );/* Tell the adapter where the TX/RX rings are located. */ -dc2114x_outl (dev,phys_to_bus ((u32)&rx_ring),DE4X5_RRBA ); -dc2114x_outl (dev,phys_to_bus ((u32)&tx_ring),DE4X5_TRBA ); +dc2114x_outl (priv,phys_to_bus ((u32)&rx_ring),DE4X5_RRBA ); +dc2114x_outl (priv,phys_to_bus ((u32)&tx_ring),DE4X5_TRBA ); -start_de4x5 (dev); +start_de4x5 (priv); tx_new =0 ; rx_new =0 ; -send_setup_frame (dev, bis); +send_setup_frame (priv, bis);return 0 ; }static void dc21x4x_halt (struct eth_device *dev) { +struct dc2114x_priv *priv = + container_of(dev, struct dc2114x_priv, dev);int devbusfn = (int )dev->priv; -stop_de4x5 (dev); -dc2114x_outl (dev,0 ,DE4X5_SICR ); +stop_de4x5 (priv); +dc2114x_outl (priv,0 ,DE4X5_SICR );pci_write_config_byte (devbusfn,PCI_CFDA_PSM ,SLEEP ); }
@@ -473,7 +480,7 @@ static void read_hw_addr(struct dc2114x_priv *priv)int i, j =0 ;for (i =0 ; i < (ETH_ALEN >>1 ); i++) { - tmp =read_srom (dev,DE4X5_APROM , (SROM_HWADD >>1 ) + i); + tmp =read_srom (priv,DE4X5_APROM , (SROM_HWADD >>1 ) + i); *p =le16_to_cpu (tmp); j += *p++; }
Signature · 1 line
2.27.0
PATCH 8/12 net: dc2114x: Pass PCI BDF into phys_to_bus()
In reply to Marek VasutThis is a trick in preparation for adding DM support. By passing in the PCI BDF into the phys_to_bus() macros and calling that dev, we can substitute dev with udevice when DM support lands and do minor adjustment to the macros to support both DM and non-DM operation. No functional change.
--- drivers/net/dc2114x.c | 29 ++++++++++++++++------------- 1 file changed, 16 insertions(+), 13 deletions(-)
drivers/net/dc2114x.c +16 -13
@@ -74,9 +74,9 @@#define POLL_DEMAND 1#if defined(CONFIG_E500 ) -#define phys_to_bus (a) (a) +#define phys_to_bus (dev, a) (a)#else -#define phys_to_bus (a) pci_phys_to_mem((pci_dev_t)dev->priv, a) +#define phys_to_bus (dev, a) pci_phys_to_mem((dev), (a))#endif #define NUM_RX_DESC PKTBUFSRX
@@ -96,6 +96,7 @@ struct de4x5_desc {struct dc2114x_priv {struct eth_device dev; +pci_dev_t devno;char *name;void __iomem *iobase;u8 *enetaddr;
@@ -278,7 +279,6 @@ static int read_srom(struct dc2114x_priv *priv, u_long ioaddr, int index)static void send_setup_frame (struct dc2114x_priv *priv,bd_t *bis) { -struct eth_device *dev = &priv->dev;char setup_frame[SETUP_FRAME_LEN ];char *pa = &setup_frame[0 ];int i;
@@ -299,7 +299,8 @@ static void send_setup_frame(struct dc2114x_priv *priv, bd_t *bis)return ; } - tx_ring[tx_new].buf =cpu_to_le32 (phys_to_bus ((u32)&setup_frame[0 ])); + tx_ring[tx_new].buf =cpu_to_le32 (phys_to_bus (priv->devno, + (u32)&setup_frame[0 ])); tx_ring[tx_new].des1 =cpu_to_le32 (TD_TER |TD_SET |SETUP_FRAME_LEN ); tx_ring[tx_new].status =cpu_to_le32 (T_OWN );
@@ -341,7 +342,8 @@ static int dc21x4x_send(struct eth_device *dev, void *packet, int length) goto done; } - tx_ring[tx_new].buf =cpu_to_le32 (phys_to_bus ((u32 )packet)); + tx_ring[tx_new].buf =cpu_to_le32 (phys_to_bus (priv->devno, + (u32 )packet)); tx_ring[tx_new].des1 =cpu_to_le32 (TD_TER |TD_LS |TD_FS | length); tx_ring[tx_new].status =cpu_to_le32 (T_OWN );
@@ -411,11 +413,10 @@ static int dc21x4x_init(struct eth_device *dev, bd_t *bis) {struct dc2114x_priv *priv = container_of(dev, struct dc2114x_priv, dev); -int devbusfn = (int )dev->priv;int i;/* Ensure we're not sleeping. */ -pci_write_config_byte (devbusfn,PCI_CFDA_PSM ,WAKEUP ); +pci_write_config_byte (priv->devno,PCI_CFDA_PSM ,WAKEUP );reset_de4x5 (priv);
@@ -429,8 +430,8 @@ static int dc21x4x_init(struct eth_device *dev, bd_t *bis)for (i =0 ; i <NUM_RX_DESC ; i++) { rx_ring[i].status =cpu_to_le32 (R_OWN ); rx_ring[i].des1 =cpu_to_le32 (RX_BUFF_SZ ); - rx_ring[i].buf = -cpu_to_le32 (phys_to_bus ((u32 )net_rx_packets[i])); + rx_ring[i].buf =cpu_to_le32 (phys_to_bus (priv->devno, + (u32 )net_rx_packets[i])); rx_ring[i].next =0 ; }
@@ -449,8 +450,10 @@ static int dc21x4x_init(struct eth_device *dev, bd_t *bis) tx_ring[tx_ring_size -1 ].des1 |=cpu_to_le32 (TD_TER );/* Tell the adapter where the TX/RX rings are located. */ -dc2114x_outl (priv,phys_to_bus ((u32)&rx_ring),DE4X5_RRBA ); -dc2114x_outl (priv,phys_to_bus ((u32)&tx_ring),DE4X5_TRBA ); +dc2114x_outl (priv,phys_to_bus (priv->devno, (u32)&rx_ring), +DE4X5_RRBA ); +dc2114x_outl (priv,phys_to_bus (priv->devno, (u32)&tx_ring), +DE4X5_TRBA );start_de4x5 (priv);
@@ -466,12 +469,11 @@ static void dc21x4x_halt(struct eth_device *dev) {struct dc2114x_priv *priv = container_of(dev, struct dc2114x_priv, dev); -int devbusfn = (int )dev->priv;stop_de4x5 (priv);dc2114x_outl (priv,0 ,DE4X5_SICR ); -pci_write_config_byte (devbusfn,PCI_CFDA_PSM ,SLEEP ); +pci_write_config_byte (priv->devno,PCI_CFDA_PSM ,SLEEP ); }static void read_hw_addr (struct dc2114x_priv *priv)
@@ -551,6 +553,7 @@ int dc21x4x_initialize(bd_t *bis) dev = &priv->dev;sprintf (dev->name,"dc21x4x#%d" , card_number); + priv->devno = devbusfn; priv->name = dev->name; priv->enetaddr = dev->enetaddr;
Signature · 1 line
2.27.0
PATCH 9/12 net: dc2114x: Add RX/TX rings into the private data
In reply to Marek VasutThe RX/TX DMA descriptor rings are per-device-instance private data, so move them into the private data.
--- drivers/net/dc2114x.c | 92 +++++++++++++++++++++---------------------- 1 file changed, 46 insertions(+), 46 deletions(-)
drivers/net/dc2114x.c +46 -46
@@ -95,6 +95,12 @@ struct de4x5_desc { };struct dc2114x_priv { +struct de4x5_desc rx_ring[NUM_RX_DESC ]__aligned(32) ; +struct de4x5_desc tx_ring[NUM_TX_DESC ]__aligned(32) ; +int rx_new;/* RX descriptor ring pointer */ +int tx_new;/* TX descriptor ring pointer */ +char rx_ring_size; +char tx_ring_size;struct eth_device dev;pci_dev_t devno;char *name;
@@ -103,14 +109,6 @@ struct dc2114x_priv { };/* RX and TX descriptor ring */ -static struct de4x5_desc rx_ring[NUM_RX_DESC ]__aligned(32) ; -static struct de4x5_desc tx_ring[NUM_TX_DESC ]__aligned(32) ; -static int rx_new;/* RX descriptor ring pointer */ -static int tx_new;/* TX descriptor ring pointer */ - -static char rx_ring_size; -static char tx_ring_size; -static u32 dc2114x_inl (struct dc2114x_priv *priv,u32 addr) {return le32_to_cpu (readl (priv->iobase + addr));
@@ -291,7 +289,7 @@ static void send_setup_frame(struct dc2114x_priv *priv, bd_t *bis) pa +=4 ; } -for (i =0 ; tx_ring[tx_new].status &cpu_to_le32 (T_OWN ); i++) { +for (i =0 ; priv->tx_ring[priv->tx_new].status &cpu_to_le32 (T_OWN ); i++) {if (i <TOUT_LOOP )continue ;
@@ -299,14 +297,14 @@ static void send_setup_frame(struct dc2114x_priv *priv, bd_t *bis)return ; } - tx_ring[tx_new].buf =cpu_to_le32 (phys_to_bus (priv->devno, + priv->tx_ring[priv->tx_new].buf =cpu_to_le32 (phys_to_bus (priv->devno, (u32)&setup_frame[0 ])); - tx_ring[tx_new].des1 =cpu_to_le32 (TD_TER |TD_SET |SETUP_FRAME_LEN ); - tx_ring[tx_new].status =cpu_to_le32 (T_OWN ); + priv->tx_ring[priv->tx_new].des1 =cpu_to_le32 (TD_TER |TD_SET |SETUP_FRAME_LEN ); + priv->tx_ring[priv->tx_new].status =cpu_to_le32 (T_OWN );dc2114x_outl (priv,POLL_DEMAND ,DE4X5_TPD ); -for (i =0 ; tx_ring[tx_new].status &cpu_to_le32 (T_OWN ); i++) { +for (i =0 ; priv->tx_ring[priv->tx_new].status &cpu_to_le32 (T_OWN ); i++) {if (i <TOUT_LOOP )continue ;
@@ -314,12 +312,12 @@ static void send_setup_frame(struct dc2114x_priv *priv, bd_t *bis)return ; } -if (le32_to_cpu (tx_ring[tx_new].status) !=0x7FFFFFFF ) { +if (le32_to_cpu (priv->tx_ring[priv->tx_new].status) !=0x7FFFFFFF ) {printf ("TX error status2 = 0x%08X\n" , -le32_to_cpu (tx_ring[tx_new].status)); +le32_to_cpu (priv->tx_ring[priv->tx_new].status)); } - tx_new = (tx_new +1 ) %NUM_TX_DESC ; + priv->tx_new = (priv->tx_new +1 ) %NUM_TX_DESC ; }static int dc21x4x_send (struct eth_device *dev,void *packet,int length)
@@ -334,7 +332,7 @@ static int dc21x4x_send(struct eth_device *dev, void *packet, int length) goto done; } -for (i =0 ; tx_ring[tx_new].status &cpu_to_le32 (T_OWN ); i++) { +for (i =0 ; priv->tx_ring[priv->tx_new].status &cpu_to_le32 (T_OWN ); i++) {if (i <TOUT_LOOP )continue ;
@@ -342,14 +340,14 @@ static int dc21x4x_send(struct eth_device *dev, void *packet, int length) goto done; } - tx_ring[tx_new].buf =cpu_to_le32 (phys_to_bus (priv->devno, + priv->tx_ring[priv->tx_new].buf =cpu_to_le32 (phys_to_bus (priv->devno, (u32 )packet)); - tx_ring[tx_new].des1 =cpu_to_le32 (TD_TER |TD_LS |TD_FS | length); - tx_ring[tx_new].status =cpu_to_le32 (T_OWN ); + priv->tx_ring[priv->tx_new].des1 =cpu_to_le32 (TD_TER |TD_LS |TD_FS | length); + priv->tx_ring[priv->tx_new].status =cpu_to_le32 (T_OWN );dc2114x_outl (priv,POLL_DEMAND ,DE4X5_TPD ); -for (i =0 ; tx_ring[tx_new].status &cpu_to_le32 (T_OWN ); i++) { +for (i =0 ; priv->tx_ring[priv->tx_new].status &cpu_to_le32 (T_OWN ); i++) {if (i <TOUT_LOOP )continue ;
@@ -357,25 +355,27 @@ static int dc21x4x_send(struct eth_device *dev, void *packet, int length) goto done; } -if (le32_to_cpu (tx_ring[tx_new].status) &TD_ES ) { - tx_ring[tx_new].status =0x0 ; +if (le32_to_cpu (priv->tx_ring[priv->tx_new].status) &TD_ES ) { + priv->tx_ring[priv->tx_new].status =0x0 ; goto done; } status = length; done: - tx_new = (tx_new +1 ) %NUM_TX_DESC ; + priv->tx_new = (priv->tx_new +1 ) %NUM_TX_DESC ;return status; }static int dc21x4x_recv (struct eth_device *dev) { +struct dc2114x_priv *priv = + container_of(dev, struct dc2114x_priv, dev);int length =0 ;u32 status;while (true) { - status =le32_to_cpu (rx_ring[rx_new].status); + status =le32_to_cpu (priv->rx_ring[priv->rx_new].status);if (status &R_OWN )break ;
@@ -387,23 +387,23 @@ static int dc21x4x_recv(struct eth_device *dev)printf ("RX error status = 0x%08X\n" , status); }else {/* A valid frame received. */ - length = (le32_to_cpu (rx_ring[rx_new].status) + length = (le32_to_cpu (priv->rx_ring[priv->rx_new].status) >>16 );/* Pass the packet up to the protocol layers */ net_process_received_packet - (net_rx_packets[rx_new], length -4 ); + (net_rx_packets[priv->rx_new], length -4 ); }/* * Change buffer ownership for this frame, * back to the adapter. */ - rx_ring[rx_new].status =cpu_to_le32 (R_OWN ); + priv->rx_ring[priv->rx_new].status =cpu_to_le32 (R_OWN ); }/* Update entry information. */ - rx_new = (rx_new +1 ) % rx_ring_size; + priv->rx_new = (priv->rx_new +1 ) % priv->rx_ring_size; }return length;
@@ -428,37 +428,37 @@ static int dc21x4x_init(struct eth_device *dev, bd_t *bis)dc2114x_outl (priv,OMR_SDP |OMR_PS |OMR_PM ,DE4X5_OMR );for (i =0 ; i <NUM_RX_DESC ; i++) { - rx_ring[i].status =cpu_to_le32 (R_OWN ); - rx_ring[i].des1 =cpu_to_le32 (RX_BUFF_SZ ); - rx_ring[i].buf =cpu_to_le32 (phys_to_bus (priv->devno, + priv->rx_ring[i].status =cpu_to_le32 (R_OWN ); + priv->rx_ring[i].des1 =cpu_to_le32 (RX_BUFF_SZ ); + priv->rx_ring[i].buf =cpu_to_le32 (phys_to_bus (priv->devno, (u32 )net_rx_packets[i])); - rx_ring[i].next =0 ; + priv->rx_ring[i].next =0 ; }for (i =0 ; i <NUM_TX_DESC ; i++) { - tx_ring[i].status =0 ; - tx_ring[i].des1 =0 ; - tx_ring[i].buf =0 ; - tx_ring[i].next =0 ; + priv->tx_ring[i].status =0 ; + priv->tx_ring[i].des1 =0 ; + priv->tx_ring[i].buf =0 ; + priv->tx_ring[i].next =0 ; } - rx_ring_size =NUM_RX_DESC ; - tx_ring_size =NUM_TX_DESC ; + priv->rx_ring_size =NUM_RX_DESC ; + priv->tx_ring_size =NUM_TX_DESC ;/* Write the end of list marker to the descriptor lists. */ - rx_ring[rx_ring_size -1 ].des1 |=cpu_to_le32 (RD_RER ); - tx_ring[tx_ring_size -1 ].des1 |=cpu_to_le32 (TD_TER ); + priv->rx_ring[priv->rx_ring_size -1 ].des1 |=cpu_to_le32 (RD_RER ); + priv->tx_ring[priv->tx_ring_size -1 ].des1 |=cpu_to_le32 (TD_TER );/* Tell the adapter where the TX/RX rings are located. */ -dc2114x_outl (priv,phys_to_bus (priv->devno, (u32)&rx_ring), +dc2114x_outl (priv,phys_to_bus (priv->devno, (u32)&priv->rx_ring),DE4X5_RRBA ); -dc2114x_outl (priv,phys_to_bus (priv->devno, (u32)&tx_ring), +dc2114x_outl (priv,phys_to_bus (priv->devno, (u32)&priv->tx_ring),DE4X5_TRBA );start_de4x5 (priv); - tx_new =0 ; - rx_new =0 ; + priv->tx_new =0 ; + priv->rx_new =0 ;send_setup_frame (priv, bis);
@@ -543,7 +543,7 @@ int dc21x4x_initialize(bd_t *bis) iobase &=PCI_BASE_ADDRESS_MEM_MASK ;debug ("dc21x4x: DEC 21142 PCI Device @0x%x\n" , iobase); - priv =malloc (sizeof (*priv)); + priv =memalign (32 ,sizeof (*priv));if (!priv) {printf ("Can not allocalte memory of dc21x4x\n" );break ;
Signature · 1 line
2.27.0
PATCH 10/12 net: dc2114x: Split RX path
In reply to Marek VasutSplit the RX data check from the rest of the RX function, so that the check can be performed separately from the processing of the packet and the release of the received packet once the processing is finished.
--- drivers/net/dc2114x.c | 67 +++++++++++++++++++++++++++---------------- 1 file changed, 43 insertions(+), 24 deletions(-)
drivers/net/dc2114x.c +43 -24
@@ -367,41 +367,60 @@ done:return status; } +static int dc21x4x_recv_check (struct dc2114x_priv *priv) +{ +int length =0 ; +u32 status; + + status =le32_to_cpu (priv->rx_ring[priv->rx_new].status); + +if (status &R_OWN ) +return 0 ; + +if (status &RD_LS ) { +/* Valid frame status. */ +if (status &RD_ES ) { +/* There was an error. */ +printf ("RX error status = 0x%08X\n" , status); +return -EINVAL ; + }else { +/* A valid frame received. */ + length = (le32_to_cpu (priv->rx_ring[priv->rx_new].status) + >>16 ); + +return length; + } + } + +return -EAGAIN ; +} +static int dc21x4x_recv (struct eth_device *dev) {struct dc2114x_priv *priv = container_of(dev, struct dc2114x_priv, dev);int length =0 ; -u32 status; +int ret;while (true) { - status =le32_to_cpu (priv->rx_ring[priv->rx_new].status); - -if (status &R_OWN ) + ret =dc21x4x_recv_check (priv); +if (!ret)break ; -if (status &RD_LS ) { -/* Valid frame status. */ -if (status &RD_ES ) { -/* There was an error. */ -printf ("RX error status = 0x%08X\n" , status); - }else { -/* A valid frame received. */ - length = (le32_to_cpu (priv->rx_ring[priv->rx_new].status) - >>16 ); - -/* Pass the packet up to the protocol layers */ -net_process_received_packet - (net_rx_packets[priv->rx_new], length -4 ); - } - -/* -* Change buffer ownership for this frame, -* back to the adapter. -*/ - priv->rx_ring[priv->rx_new].status =cpu_to_le32 (R_OWN ); +if (ret >0 ) { + length = ret; +/* Pass the packet up to the protocol layers */ +net_process_received_packet + (net_rx_packets[priv->rx_new], length -4 ); } +/* +* Change buffer ownership for this frame, +* back to the adapter. +*/ +if (ret != -EAGAIN ) + priv->rx_ring[priv->rx_new].status =cpu_to_le32 (R_OWN ); +/* Update entry information. */ priv->rx_new = (priv->rx_new +1 ) % priv->rx_ring_size; }
Signature · 1 line
2.27.0
PATCH 11/12 net: dc2114x: Split common parts of non-DM functions out
In reply to Marek VasutSplit the common code from the non-DM code, so it can be reused by the DM code later. As always, the recv() function had to be split into the actual receiving part and free_pkt part to fit with the DM.
--- drivers/net/dc2114x.c | 117 ++++++++++++++++++++++++------------------ 1 file changed, 67 insertions(+), 50 deletions(-)
drivers/net/dc2114x.c +67 -50
@@ -275,7 +275,7 @@ static int read_srom(struct dc2114x_priv *priv, u_long ioaddr, int index) 3 + ee_addr_size + 16); } -static void send_setup_frame (struct dc2114x_priv *priv,bd_t *bis) +static void send_setup_frame (struct dc2114x_priv *priv) {char setup_frame[SETUP_FRAME_LEN ];char *pa = &setup_frame[0 ];
@@ -320,10 +320,8 @@ static void send_setup_frame(struct dc2114x_priv *priv, bd_t *bis) priv->tx_new = (priv->tx_new +1 ) %NUM_TX_DESC ; } -static int dc21x4x_send (struct eth_device *dev,void *packet,int length) +static int dc21x4x_send_common (struct dc2114x_priv *priv,void *packet,int length) { -struct dc2114x_priv *priv = - container_of(dev, struct dc2114x_priv, dev);int status =-1 ;int i;
@@ -395,48 +393,10 @@ static int dc21x4x_recv_check(struct dc2114x_priv *priv)return -EAGAIN ; } -static int dc21x4x_recv (struct eth_device *dev) -{ -struct dc2114x_priv *priv = - container_of(dev, struct dc2114x_priv, dev); -int length =0 ; -int ret; - -while (true) { - ret =dc21x4x_recv_check (priv); -if (!ret) -break ; - -if (ret >0 ) { - length = ret; -/* Pass the packet up to the protocol layers */ -net_process_received_packet - (net_rx_packets[priv->rx_new], length -4 ); - } - -/* -* Change buffer ownership for this frame, -* back to the adapter. -*/ -if (ret != -EAGAIN ) - priv->rx_ring[priv->rx_new].status =cpu_to_le32 (R_OWN ); - -/* Update entry information. */ - priv->rx_new = (priv->rx_new +1 ) % priv->rx_ring_size; - } - -return length; -} - -static int dc21x4x_init (struct eth_device *dev,bd_t *bis) +static int dc21x4x_init_common (struct dc2114x_priv *priv) { -struct dc2114x_priv *priv = - container_of(dev, struct dc2114x_priv, dev);int i; -/* Ensure we're not sleeping. */ -pci_write_config_byte (priv->devno,PCI_CFDA_PSM ,WAKEUP ); -reset_de4x5 (priv);if (dc2114x_inl (priv,DE4X5_STS ) & (STS_TS |STS_RS )) {
@@ -479,20 +439,15 @@ static int dc21x4x_init(struct eth_device *dev, bd_t *bis) priv->tx_new =0 ; priv->rx_new =0 ; -send_setup_frame (priv, bis); +send_setup_frame (priv);return 0 ; } -static void dc21x4x_halt (struct eth_device *dev) +static void dc21x4x_halt_common (struct dc2114x_priv *priv) { -struct dc2114x_priv *priv = - container_of(dev, struct dc2114x_priv, dev); -stop_de4x5 (priv);dc2114x_outl (priv,0 ,DE4X5_SICR ); - -pci_write_config_byte (priv->devno,PCI_CFDA_PSM ,SLEEP ); }static void read_hw_addr (struct dc2114x_priv *priv)
@@ -518,6 +473,68 @@ static struct pci_device_id supported[] = { { } }; +static int dc21x4x_init (struct eth_device *dev,bd_t *bis) +{ +struct dc2114x_priv *priv = + container_of(dev, struct dc2114x_priv, dev); + +/* Ensure we're not sleeping. */ +pci_write_config_byte (priv->devno,PCI_CFDA_PSM ,WAKEUP ); + +return dc21x4x_init_common (priv); +} + +static void dc21x4x_halt (struct eth_device *dev) +{ +struct dc2114x_priv *priv = + container_of(dev, struct dc2114x_priv, dev); + +dc21x4x_halt_common (priv); + +pci_write_config_byte (priv->devno,PCI_CFDA_PSM ,SLEEP ); +} + +static int dc21x4x_send (struct eth_device *dev,void *packet,int length) +{ +struct dc2114x_priv *priv = + container_of(dev, struct dc2114x_priv, dev); + +return dc21x4x_send_common (priv, packet, length); +} + +static int dc21x4x_recv (struct eth_device *dev) +{ +struct dc2114x_priv *priv = + container_of(dev, struct dc2114x_priv, dev); +int length =0 ; +int ret; + +while (true) { + ret =dc21x4x_recv_check (priv); +if (!ret) +break ; + +if (ret >0 ) { + length = ret; +/* Pass the packet up to the protocol layers */ +net_process_received_packet + (net_rx_packets[priv->rx_new], length -4 ); + } + +/* +* Change buffer ownership for this frame, +* back to the adapter. +*/ +if (ret != -EAGAIN ) + priv->rx_ring[priv->rx_new].status =cpu_to_le32 (R_OWN ); + +/* Update entry information. */ + priv->rx_new = (priv->rx_new +1 ) % priv->rx_ring_size; + } + +return length; +} +int dc21x4x_initialize (bd_t *bis) {struct dc2114x_priv *priv;
Signature · 1 line
2.27.0
PATCH 12/12 net: dc2114x: Add DM support
In reply to Marek VasutWith all the changes in place, add support for DM into the dc2114x driver.
--- drivers/net/dc2114x.c | 147 +++++++++++++++++++++++++++++++++++++++++- 1 file changed, 145 insertions(+), 2 deletions(-)
drivers/net/dc2114x.c +145 -2
@@ -2,7 +2,7 @@#include <common.h> #include <asm/io.h> -#include <env.h> +#include <dm.h> #include <malloc.h> #include <net.h> #include <netdev.h>
@@ -73,7 +73,9 @@#define POLL_DEMAND 1 -#if defined(CONFIG_E500 ) +#if defined(CONFIG_DM_ETH ) +#define phys_to_bus (dev, a) dm_pci_phys_to_mem((dev), (a)) +#elif defined(CONFIG_E500 )#define phys_to_bus (dev, a) (a)#else #define phys_to_bus (dev, a) pci_phys_to_mem((dev), (a))
@@ -101,8 +103,12 @@ struct dc2114x_priv {int tx_new;/* TX descriptor ring pointer */ char rx_ring_size;char tx_ring_size; +#ifdef CONFIG_DM_ETH +struct udevice *devno; +#else struct eth_device dev;pci_dev_t devno; +#endif char *name;void __iomem *iobase;u8 *enetaddr;
@@ -473,6 +479,7 @@ static struct pci_device_id supported[] = { { } }; +#ifndef CONFIG_DM_ETH static int dc21x4x_init (struct eth_device *dev,bd_t *bis) { struct dc2114x_priv *priv =
@@ -614,3 +621,139 @@ int dc21x4x_initialize(bd_t *bis)return card_number; } + +#else /* DM_ETH */ +static int dc2114x_start (struct udevice *dev) +{ +struct eth_pdata *plat =dev_get_platdata (dev); +struct dc2114x_priv *priv =dev_get_priv (dev); + +memcpy (priv->enetaddr, plat->enetaddr,sizeof (plat->enetaddr)); + +/* Ensure we're not sleeping. */ +dm_pci_write_config8 (dev,PCI_CFDA_PSM ,WAKEUP ); + +return dc21x4x_init_common (priv); +} + +static void dc2114x_stop (struct udevice *dev) +{ +struct dc2114x_priv *priv =dev_get_priv (dev); + +dc21x4x_halt_common (priv); + +dm_pci_write_config8 (dev,PCI_CFDA_PSM ,SLEEP ); +} + +static int dc2114x_send (struct udevice *dev,void *packet,int length) +{ +struct dc2114x_priv *priv =dev_get_priv (dev); +int ret; + + ret =dc21x4x_send_common (priv, packet, length); + +return ret ?0 : -ETIMEDOUT ; +} + +static int dc2114x_recv (struct udevice *dev,int flags,uchar **packetp) +{ +struct dc2114x_priv *priv =dev_get_priv (dev); +int ret; + + ret =dc21x4x_recv_check (priv); + +if (ret <0 ) { +/* Update entry information. */ + priv->rx_new = (priv->rx_new +1 ) % priv->rx_ring_size; + ret =0 ; + } + +if (!ret) +return 0 ; + + *packetp = net_rx_packets[priv->rx_new]; + +return ret -4 ; +} + +static int dc2114x_free_pkt (struct udevice *dev,uchar *packet,int length) +{ +struct dc2114x_priv *priv =dev_get_priv (dev); + + priv->rx_ring[priv->rx_new].status =cpu_to_le32 (R_OWN ); + +/* Update entry information. */ + priv->rx_new = (priv->rx_new +1 ) % priv->rx_ring_size; + +return 0 ; +} + +static int dc2114x_read_rom_hwaddr (struct udevice *dev) +{ +struct dc2114x_priv *priv =dev_get_priv (dev); + +read_hw_addr (priv); + +return 0 ; +} + +static int dc2114x_bind (struct udevice *dev) +{ +static int card_number; +char name[16 ]; + +sprintf (name,"dc2114x#%u" , card_number++); + +return device_set_name (dev, name); +} + +static int dc2114x_probe (struct udevice *dev) +{ +struct eth_pdata *plat =dev_get_platdata (dev); +struct dc2114x_priv *priv =dev_get_priv (dev); +u16 command, status; +u32 iobase; + +dm_pci_read_config32 (dev,PCI_BASE_ADDRESS_1 , &iobase); + iobase &= ~0xf ; + +debug ("dc2114x: DEC 2114x PCI Device @0x%x\n" , iobase); + + priv->devno = dev; + priv->enetaddr = plat->enetaddr; + priv->iobase = (void __iomem *)dm_pci_mem_to_phys (dev, iobase); + + command =PCI_COMMAND_MEMORY |PCI_COMMAND_MASTER ; +dm_pci_write_config16 (dev,PCI_COMMAND , command); +dm_pci_read_config16 (dev,PCI_COMMAND , &status); +if ((status & command) != command) { +printf ("dc2114x: Couldn't enable IO access or Bus Mastering\n" ); +return -EINVAL ; + } + +dm_pci_write_config8 (dev,PCI_LATENCY_TIMER ,0x60 ); + +return 0 ; +} + +static const struct eth_ops dc2114x_ops = { + .start = dc2114x_start, + .send = dc2114x_send, + .recv = dc2114x_recv, + .stop = dc2114x_stop, + .free_pkt = dc2114x_free_pkt, + .read_rom_hwaddr = dc2114x_read_rom_hwaddr, +}; + +U_BOOT_DRIVER (eth_dc2114x) = { + .name ="eth_dc2114x" , + .id =UCLASS_ETH , + .bind = dc2114x_bind, + .probe = dc2114x_probe, + .ops = &dc2114x_ops, + .priv_auto_alloc_size =sizeof (struct dc2114x_priv ), + .platdata_auto_alloc_size =sizeof (struct eth_pdata ), +}; + +U_BOOT_PCI_DEVICE (eth_dc2114x, supported); +#endif
Signature · 1 line
2.27.0