Skip to contentSkip to conversation

ARM: dt-bindings: stm32: Add missing DSI clock.

PATCH In review Adrian Pop 4 participants 7 messages Jul 2, 2020 – Jul 21, 2020

Subsystems (3)
lore
Share & tools
lore

Adrian Pop

author
#0 lore raw

PATCH v2 1/2 ARM: dt-bindings: stm32: Add missing DSI clock.

---
 include/dt-bindings/mfd/stm32f7-rcc.h | 1 +
 1 file changed, 1 insertion(+)
include/dt-bindings/mfd/stm32f7-rcc.h +1 -0
index a90f3613c584..ba5cb7456ee4 100644
@@ -107,6 +107,7 @@
 #define STM32F7_RCC_APB2_SAI1		22
 #define STM32F7_RCC_APB2_SAI2		23
 #define STM32F7_RCC_APB2_LTDC		26
+#define STM32F7_RCC_APB2_DSI		27
 
 #define STM32F7_APB2_RESET(bit)	(STM32F7_RCC_APB2_##bit + (0x24 * 8))
 #define STM32F7_APB2_CLOCK(bit)	(STM32F7_RCC_APB2_##bit + 0xA0)
Signature · 1 line
2.27.0
author
#1 lore raw

PATCH v2 2/2 ARM: dts: stm32: Enable MIPI DSI display support.

STM32f769-disco features a 4" MIPI DSI display: add support for it. On Cortex-M7 DMA can't use cached memory. For this reason I use a dedicated memory pool for DMA with no-cache attribute which is located at the end of
RAM.

---
 arch/arm/boot/dts/stm32f746.dtsi      | 34 +++++++++++++++++++
 arch/arm/boot/dts/stm32f769-disco.dts | 49 +++++++++++++++++++++++++++
 2 files changed, 83 insertions(+)
arch/arm/boot/dts/stm32f746.dtsi +34 -0
index 93c063796780..577a812ca01c 100644
@@ -48,6 +48,19 @@ / {
 	#address-cells = <1>;
 	#size-cells = <1>;
 
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,dma {
+			compatible = "shared-dma-pool";
+			linux,dma-default;
+			no-map;
+			reg = <0xc0f00000 0x100000>;
+		};
+	};
+
 	clocks {
 		clk_hse: clk-hse {
 			#clock-cells = <0>;
@@ -75,6 +88,27 @@ clk_i2s_ckin: clk-i2s-ckin {
 	};
 
 	soc {
+		ltdc: display-controller@40016800 {
+			compatible = "st,stm32-ltdc";
+			reg = <0x40016800 0x200>;
+			interrupts = <88>, <89>;
+			resets = <&rcc STM32F7_APB2_RESET(LTDC)>;
+			clocks = <&rcc 1 CLK_LCD>;
+			clock-names = "lcd";
+			status = "disabled";
+		};
+
+		dsi: dsi@40016c00 {
+			compatible = "st,stm32-dsi";
+			reg = <0x40016c00 0x800>;
+			interrupts = <98>;
+			clocks = <&rcc 1 CLK_F769_DSI>, <&clk_hse>;
+			clock-names = "pclk", "ref";
+			resets = <&rcc STM32F7_APB2_RESET(DSI)>;
+			reset-names = "apb";
+			status = "disabled";
+		};
+
 		timer2: timer@40000000 {
 			compatible = "st,stm32-timer";
 			reg = <0x40000000 0x400>;
arch/arm/boot/dts/stm32f769-disco.dts +49 -0

52 lines not on this page · raw message

Signature · 1 line
2.27.0
maintainer
#2 lore raw

Re: [PATCH v2 2/2] ARM: dts: stm32: Enable MIPI DSI display support.

Quoted 16 lines · Adrian Pop

STM32f769-disco features a 4" MIPI DSI display: add support for it. On Cortex-M7 DMA can't use cached memory. For this reason I use a dedicated memory pool for DMA with no-cache attribute which is located at the end of
RAM.

---
 arch/arm/boot/dts/stm32f746.dtsi      | 34 +++++++++++++++++++
 arch/arm/boot/dts/stm32f769-disco.dts | 49 +++++++++++++++++++++++++++
 2 files changed, 83 insertions(+)
arch/arm/boot/dts/stm32f746.dtsi +0 -0
index 93c063796780..577a812ca01c 100644

arch/arm/boot/dts/stm32f746.dtsi / { · line 56

Quoted 9 lines
arch/arm/boot/dts/stm32f746.dtsi +6 -0
@@ -48,6 +48,19 @@ / {
 	#address-cells = <1>;
 	#size-cells = <1>;
 
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,dma {

Build your DT with W=1. This will have a warning.

Quoted 67 lines
arch/arm/boot/dts/stm32f746.dtsi +28 -0
+			compatible = "shared-dma-pool";
+			linux,dma-default;
+			no-map;
+			reg = <0xc0f00000 0x100000>;
+		};
+	};
+
 	clocks {
 		clk_hse: clk-hse {
 			#clock-cells = <0>;
@@ -75,6 +88,27 @@ clk_i2s_ckin: clk-i2s-ckin {
 	};
 
 	soc {
+		ltdc: display-controller@40016800 {
+			compatible = "st,stm32-ltdc";
+			reg = <0x40016800 0x200>;
+			interrupts = <88>, <89>;
+			resets = <&rcc STM32F7_APB2_RESET(LTDC)>;
+			clocks = <&rcc 1 CLK_LCD>;
+			clock-names = "lcd";
+			status = "disabled";
+		};
+
+		dsi: dsi@40016c00 {
+			compatible = "st,stm32-dsi";
+			reg = <0x40016c00 0x800>;
+			interrupts = <98>;
+			clocks = <&rcc 1 CLK_F769_DSI>, <&clk_hse>;
+			clock-names = "pclk", "ref";
+			resets = <&rcc STM32F7_APB2_RESET(DSI)>;
+			reset-names = "apb";
+			status = "disabled";
+		};
+
 		timer2: timer@40000000 {
 			compatible = "st,stm32-timer";
 			reg = <0x40000000 0x400>;
arch/arm/boot/dts/stm32f769-disco.dts +21 -0
index 1626e00bb2cb..a9e81b49809c 100644
@@ -153,3 +153,52 @@ &usbotg_hs {
 	pinctrl-names = "default";
 	status = "okay";
 };
+
+&dsi {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			dsi_in: endpoint {
+				remote-endpoint = <&ltdc_out_dsi>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			dsi_out: endpoint {
+				remote-endpoint = <&dsi_in_panel>;

arch/arm/boot/dts/stm32f769-disco.dts &usbotg_hs { · line 186

Quoted 10 lines
arch/arm/boot/dts/stm32f769-disco.dts +10 -0
+			};
+		};
+
+	};
+
+	panel: panel {
+		compatible = "orisetech,otm8009a";
+		reg = <0>;
+		reset-gpios = <&gpioj 15 GPIO_ACTIVE_LOW>;
+		status = "okay";

Don't need status. Enabled is the default.

Quoted 21 lines
arch/arm/boot/dts/stm32f769-disco.dts +18 -0
+
+		port {
+			dsi_in_panel: endpoint {
+				remote-endpoint = <&dsi_out>;
+			};
+		};
+	};
+};
+
+&ltdc {
+	status = "okay";
+
+	port {
+		ltdc_out_dsi: endpoint {
+			remote-endpoint = <&dsi_in>;
+		};
+	};
+};
Signature · 1 line
2.27.0
#3 lore raw

Re: [PATCH v2 2/2] ARM: dts: stm32: Enable MIPI DSI display support.

In reply to Adrian Pop

Hi, Adrian,

Just one suggestion for you.

Quoted 23 lines · Adrian Pop <[email protected]> 于2020年7月3日周五 上午1:30写道:

STM32f769-disco features a 4" MIPI DSI display: add support for it. On Cortex-M7 DMA can't use cached memory. For this reason I use a dedicated memory pool for DMA with no-cache attribute which is located at the end of
RAM.

---
 arch/arm/boot/dts/stm32f746.dtsi      | 34 +++++++++++++++++++
 arch/arm/boot/dts/stm32f769-disco.dts | 49 +++++++++++++++++++++++++++
 2 files changed, 83 insertions(+)
arch/arm/boot/dts/stm32f746.dtsi +3 -0
index 93c063796780..577a812ca01c 100644
@@ -48,6 +48,19 @@ / {
        #address-cells = <1>;
        #size-cells = <1>;
 
+       reserved-memory {
+               #address-cells = <1>;
+               #size-cells = <1>;

arch/arm/boot/dts/stm32f746.dtsi / { · line 63

Quoted 10 lines
arch/arm/boot/dts/stm32f746.dtsi +10 -0
+               ranges;
+
+               linux,dma {
+                       compatible = "shared-dma-pool";
+                       linux,dma-default;
+                       no-map;
+                       reg = <0xc0f00000 0x100000>;
+               };
+       };
+

Christoph Hellwig was submit a patch for !CONFIG_MMU platforms to support mmap. the patch is : 1fbf57d05302 dma-direct: re-enable mmap for !CONFIG_MMU i thought there is no need to create a reserved-memory for it.

Quoted 96 lines
arch/arm/boot/dts/stm32f746.dtsi +21 -0
        clocks {
                clk_hse: clk-hse {
                        #clock-cells = <0>;
@@ -75,6 +88,27 @@ clk_i2s_ckin: clk-i2s-ckin {
        };
 
        soc {
+               ltdc: display-controller@40016800 {
+                       compatible = "st,stm32-ltdc";
+                       reg = <0x40016800 0x200>;
+                       interrupts = <88>, <89>;
+                       resets = <&rcc STM32F7_APB2_RESET(LTDC)>;
+                       clocks = <&rcc 1 CLK_LCD>;
+                       clock-names = "lcd";
+                       status = "disabled";
+               };
+
+               dsi: dsi@40016c00 {
+                       compatible = "st,stm32-dsi";
+                       reg = <0x40016c00 0x800>;
+                       interrupts = <98>;
+                       clocks = <&rcc 1 CLK_F769_DSI>, <&clk_hse>;
+                       clock-names = "pclk", "ref";
+                       resets = <&rcc STM32F7_APB2_RESET(DSI)>;
+                       reset-names = "apb";
+                       status = "disabled";
+               };
+
                timer2: timer@40000000 {
                        compatible = "st,stm32-timer";
                        reg = <0x40000000 0x400>;
arch/arm/boot/dts/stm32f769-disco.dts +49 -1
index 1626e00bb2cb..a9e81b49809c 100644
@@ -153,3 +153,52 @@ &usbotg_hs {
        pinctrl-names = "default";
        status = "okay";
 };
+
+&dsi {
+       #address-cells = <1>;
+       #size-cells = <0>;
+       status = "okay";
+
+       ports {
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               port@0 {
+                       reg = <0>;
+                       dsi_in: endpoint {
+                               remote-endpoint = <&ltdc_out_dsi>;
+                       };
+               };
+
+               port@1 {
+                       reg = <1>;
+                       dsi_out: endpoint {
+                               remote-endpoint = <&dsi_in_panel>;
+                       };
+               };
+
+       };
+
+       panel: panel {
+               compatible = "orisetech,otm8009a";
+               reg = <0>;
+               reset-gpios = <&gpioj 15 GPIO_ACTIVE_LOW>;
+               status = "okay";
+
+               port {
+                       dsi_in_panel: endpoint {
+                               remote-endpoint = <&dsi_out>;
+                       };
+               };
+       };
+};
+
+&ltdc {
+       status = "okay";
+
+       port {
+               ltdc_out_dsi: endpoint {
+                       remote-endpoint = <&dsi_in>;
+               };
+       };
+};
--

2.27.0

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

author
#4 lore raw

Re: [PATCH v2 2/2] ARM: dts: stm32: Enable MIPI DSI display support.

Hello Hua,

Thank you for your review,

Quoted 26 lines · Hua Dillon

Hi, Adrian,

Just one suggestion for you.

Quoted 20 lines · Adrian Pop <[email protected]> 于2020年7月3日周五 上午1:30写道:

STM32f769-disco features a 4" MIPI DSI display: add support for it. On Cortex-M7 DMA can't use cached memory. For this reason I use a dedicated memory pool for DMA with no-cache attribute which is located at the end of
RAM.

---
 arch/arm/boot/dts/stm32f746.dtsi      | 34 +++++++++++++++++++
 arch/arm/boot/dts/stm32f769-disco.dts | 49 +++++++++++++++++++++++++++
 2 files changed, 83 insertions(+)
arch/arm/boot/dts/stm32f746.dtsi +0 -0
index 93c063796780..577a812ca01c 100644
@@ -48,6 +48,19 @@ / {
        #address-cells = <1>;
        #size-cells = <1>;
 
Quoted 16 lines

arch/arm/boot/dts/stm32f746.dtsi / { · line 63

Quoted 13 lines
arch/arm/boot/dts/stm32f746.dtsi +13 -0
+       reserved-memory {
+               #address-cells = <1>;
+               #size-cells = <1>;
+               ranges;
+
+               linux,dma {
+                       compatible = "shared-dma-pool";
+                       linux,dma-default;
+                       no-map;
+                       reg = <0xc0f00000 0x100000>;
+               };
+       };
+

Christoph Hellwig was submit a patch for !CONFIG_MMU platforms to support mmap. the patch is : 1fbf57d05302 dma-direct: re-enable mmap for !CONFIG_MMU i thought there is no need to create a reserved-memory for it.

Just tried with his patch, if I don't have the reserved-memory, I get:

[drm] Initialized stm 1.0.0 20170330 for 40016800.display-controller on minor 0

------------[ cut here ]------------
WARNING: CPU: 0 PID: 5 at arch/arm/mm/dma-mapping-nommu.c:50 0xc000b8e9
CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.8.0-rc1-next-20200616 #4
Hardware name: STM32 (Device Tree Support)
Workqueue: events 0xc0150fc1

This is the reason I added the reserved memory in the first place.

Quoted 93 lines
Quoted 93 lines
arch/arm/boot/dts/stm32f746.dtsi +21 -0
        clocks {
                clk_hse: clk-hse {
                        #clock-cells = <0>;
@@ -75,6 +88,27 @@ clk_i2s_ckin: clk-i2s-ckin {
        };
 
        soc {
+               ltdc: display-controller@40016800 {
+                       compatible = "st,stm32-ltdc";
+                       reg = <0x40016800 0x200>;
+                       interrupts = <88>, <89>;
+                       resets = <&rcc STM32F7_APB2_RESET(LTDC)>;
+                       clocks = <&rcc 1 CLK_LCD>;
+                       clock-names = "lcd";
+                       status = "disabled";
+               };
+
+               dsi: dsi@40016c00 {
+                       compatible = "st,stm32-dsi";
+                       reg = <0x40016c00 0x800>;
+                       interrupts = <98>;
+                       clocks = <&rcc 1 CLK_F769_DSI>, <&clk_hse>;
+                       clock-names = "pclk", "ref";
+                       resets = <&rcc STM32F7_APB2_RESET(DSI)>;
+                       reset-names = "apb";
+                       status = "disabled";
+               };
+
                timer2: timer@40000000 {
                        compatible = "st,stm32-timer";
                        reg = <0x40000000 0x400>;
arch/arm/boot/dts/stm32f769-disco.dts +49 -1
index 1626e00bb2cb..a9e81b49809c 100644
@@ -153,3 +153,52 @@ &usbotg_hs {
        pinctrl-names = "default";
        status = "okay";
 };
+
+&dsi {
+       #address-cells = <1>;
+       #size-cells = <0>;
+       status = "okay";
+
+       ports {
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               port@0 {
+                       reg = <0>;
+                       dsi_in: endpoint {
+                               remote-endpoint = <&ltdc_out_dsi>;
+                       };
+               };
+
+               port@1 {
+                       reg = <1>;
+                       dsi_out: endpoint {
+                               remote-endpoint = <&dsi_in_panel>;
+                       };
+               };
+
+       };
+
+       panel: panel {
+               compatible = "orisetech,otm8009a";
+               reg = <0>;
+               reset-gpios = <&gpioj 15 GPIO_ACTIVE_LOW>;
+               status = "okay";
+
+               port {
+                       dsi_in_panel: endpoint {
+                               remote-endpoint = <&dsi_out>;
+                       };
+               };
+       };
+};
+
+&ltdc {
+       status = "okay";
+
+       port {
+               ltdc_out_dsi: endpoint {
+                       remote-endpoint = <&dsi_in>;
+               };
+       };
+};
--

2.27.0

Quoted 4 lines
Quoted 4 lines

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Regards,
Adrian

#5 lore raw

Re: [PATCH v2 2/2] ARM: dts: stm32: Enable MIPI DSI display support.

Hi Adrian,

Quoted 51 lines · Adrian Pop <[email protected]> 于2020年7月19日周日 下午10:54写道:

Hello Hua,

Thank you for your review,

Quoted 26 lines · Hua Dillon

Hi, Adrian,

Just one suggestion for you.

Quoted 20 lines · Adrian Pop <[email protected]> 于2020年7月3日周五 上午1:30写道:

STM32f769-disco features a 4" MIPI DSI display: add support for it. On Cortex-M7 DMA can't use cached memory. For this reason I use a dedicated memory pool for DMA with no-cache attribute which is located at the end of
RAM.

---
 arch/arm/boot/dts/stm32f746.dtsi      | 34 +++++++++++++++++++
 arch/arm/boot/dts/stm32f769-disco.dts | 49 +++++++++++++++++++++++++++
 2 files changed, 83 insertions(+)
arch/arm/boot/dts/stm32f746.dtsi +0 -0
index 93c063796780..577a812ca01c 100644
@@ -48,6 +48,19 @@ / {
        #address-cells = <1>;
        #size-cells = <1>;
 
Quoted 16 lines

arch/arm/boot/dts/stm32f746.dtsi / { · line 63

Quoted 13 lines
arch/arm/boot/dts/stm32f746.dtsi +13 -0
+       reserved-memory {
+               #address-cells = <1>;
+               #size-cells = <1>;
+               ranges;
+
+               linux,dma {
+                       compatible = "shared-dma-pool";
+                       linux,dma-default;
+                       no-map;
+                       reg = <0xc0f00000 0x100000>;
+               };
+       };
+

Christoph Hellwig was submit a patch for !CONFIG_MMU platforms to support mmap. the patch is : 1fbf57d05302 dma-direct: re-enable mmap for !CONFIG_MMU i thought there is no need to create a reserved-memory for it.

Just tried with his patch, if I don't have the reserved-memory, I get:

Quoted 9 lines

[drm] Initialized stm 1.0.0 20170330 for 40016800.display-controller on minor 0

------------[ cut here ]------------
WARNING: CPU: 0 PID: 5 at arch/arm/mm/dma-mapping-nommu.c:50 0xc000b8e9
CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.8.0-rc1-next-20200616 #4
Hardware name: STM32 (Device Tree Support)
Workqueue: events 0xc0150fc1

This is the reason I added the reserved memory in the first place.

Oh, sorry, i forget stm32f7 with cache inside. yes, you need a reserve memory for that case.
but, "reg = <0xc0f00000 0x100000>;" should big enough for framebuffer, as your know this is
a global reserve memory for all devices, it's might need more for other devices, like camera etc.
or use per-device reserve memory region.

thanks.

Quoted 100 lines
Quoted 93 lines
Quoted 93 lines
arch/arm/boot/dts/stm32f746.dtsi +21 -0
        clocks {
                clk_hse: clk-hse {
                        #clock-cells = <0>;
@@ -75,6 +88,27 @@ clk_i2s_ckin: clk-i2s-ckin {
        };
 
        soc {
+               ltdc: display-controller@40016800 {
+                       compatible = "st,stm32-ltdc";
+                       reg = <0x40016800 0x200>;
+                       interrupts = <88>, <89>;
+                       resets = <&rcc STM32F7_APB2_RESET(LTDC)>;
+                       clocks = <&rcc 1 CLK_LCD>;
+                       clock-names = "lcd";
+                       status = "disabled";
+               };
+
+               dsi: dsi@40016c00 {
+                       compatible = "st,stm32-dsi";
+                       reg = <0x40016c00 0x800>;
+                       interrupts = <98>;
+                       clocks = <&rcc 1 CLK_F769_DSI>, <&clk_hse>;
+                       clock-names = "pclk", "ref";
+                       resets = <&rcc STM32F7_APB2_RESET(DSI)>;
+                       reset-names = "apb";
+                       status = "disabled";
+               };
+
                timer2: timer@40000000 {
                        compatible = "st,stm32-timer";
                        reg = <0x40000000 0x400>;
arch/arm/boot/dts/stm32f769-disco.dts +49 -1
index 1626e00bb2cb..a9e81b49809c 100644
@@ -153,3 +153,52 @@ &usbotg_hs {
        pinctrl-names = "default";
        status = "okay";
 };
+
+&dsi {
+       #address-cells = <1>;
+       #size-cells = <0>;
+       status = "okay";
+
+       ports {
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               port@0 {
+                       reg = <0>;
+                       dsi_in: endpoint {
+                               remote-endpoint = <&ltdc_out_dsi>;
+                       };
+               };
+
+               port@1 {
+                       reg = <1>;
+                       dsi_out: endpoint {
+                               remote-endpoint = <&dsi_in_panel>;
+                       };
+               };
+
+       };
+
+       panel: panel {
+               compatible = "orisetech,otm8009a";
+               reg = <0>;
+               reset-gpios = <&gpioj 15 GPIO_ACTIVE_LOW>;
+               status = "okay";
+
+               port {
+                       dsi_in_panel: endpoint {
+                               remote-endpoint = <&dsi_out>;
+                       };
+               };
+       };
+};
+
+&ltdc {
+       status = "okay";
+
+       port {
+               ltdc_out_dsi: endpoint {
+                       remote-endpoint = <&dsi_in>;
+               };
+       };
+};
--

2.27.0

Quoted 4 lines
Quoted 4 lines

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Regards,
Adrian

#6 lore raw

Re: [PATCH v2 2/2] ARM: dts: stm32: Enable MIPI DSI display support.

In reply to Adrian Pop

Hi Adrian

Quoted 22 lines · Adrian Pop

STM32f769-disco features a 4" MIPI DSI display: add support for it. On Cortex-M7 DMA can't use cached memory. For this reason I use a dedicated memory pool for DMA with no-cache attribute which is located at the end of
RAM.

---
  arch/arm/boot/dts/stm32f746.dtsi      | 34 +++++++++++++++++++
  arch/arm/boot/dts/stm32f769-disco.dts | 49 +++++++++++++++++++++++++++
  2 files changed, 83 insertions(+)
arch/arm/boot/dts/stm32f746.dtsi +3 -0
index 93c063796780..577a812ca01c 100644
@@ -48,6 +48,19 @@ / {
  	#address-cells = <1>;
  	#size-cells = <1>;
 
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;

arch/arm/boot/dts/stm32f746.dtsi / { · line 63

Quoted 10 lines
arch/arm/boot/dts/stm32f746.dtsi +10 -0
+		ranges;
+
+		linux,dma {
+			compatible = "shared-dma-pool";
+			linux,dma-default;
+			no-map;
+			reg = <0xc0f00000 0x100000>;
+		};
+	};
+

Please check Rob's remark (make W=1). Furthermore this node should be declared in board dts file is should depend on SDRAM size embedded on board.

Quoted 18 lines
arch/arm/boot/dts/stm32f746.dtsi +11 -0
  	clocks {
  		clk_hse: clk-hse {
  			#clock-cells = <0>;
@@ -75,6 +88,27 @@ clk_i2s_ckin: clk-i2s-ckin {
  	};
 
  	soc {
+		ltdc: display-controller@40016800 {
+			compatible = "st,stm32-ltdc";
+			reg = <0x40016800 0x200>;
+			interrupts = <88>, <89>;
+			resets = <&rcc STM32F7_APB2_RESET(LTDC)>;
+			clocks = <&rcc 1 CLK_LCD>;
+			clock-names = "lcd";
+			status = "disabled";
+		};
+
+		dsi: dsi@40016c00 {

arch/arm/boot/dts/stm32f746.dtsi clk_i2s_ckin: clk-i2s-ckin { · line 111

Quoted 10 lines
arch/arm/boot/dts/stm32f746.dtsi +10 -0
+			compatible = "st,stm32-dsi";
+			reg = <0x40016c00 0x800>;
+			interrupts = <98>;
+			clocks = <&rcc 1 CLK_F769_DSI>, <&clk_hse>;
+			clock-names = "pclk", "ref";
+			resets = <&rcc STM32F7_APB2_RESET(DSI)>;
+			reset-names = "apb";
+			status = "disabled";
+		};
+

Nodes are ordered by address in soc dtsi file. Please follow it.

Quoted 60 lines
arch/arm/boot/dts/stm32f746.dtsi +0 -0
  		timer2: timer@40000000 {
  			compatible = "st,stm32-timer";
  			reg = <0x40000000 0x400>;
arch/arm/boot/dts/stm32f769-disco.dts +49 -0
index 1626e00bb2cb..a9e81b49809c 100644
@@ -153,3 +153,52 @@ &usbotg_hs {
  	pinctrl-names = "default";
  	status = "okay";
  };
+
+&dsi {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			dsi_in: endpoint {
+				remote-endpoint = <&ltdc_out_dsi>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			dsi_out: endpoint {
+				remote-endpoint = <&dsi_in_panel>;
+			};
+		};
+
+	};
+
+	panel: panel {
+		compatible = "orisetech,otm8009a";
+		reg = <0>;
+		reset-gpios = <&gpioj 15 GPIO_ACTIVE_LOW>;
+		status = "okay";
+
+		port {
+			dsi_in_panel: endpoint {
+				remote-endpoint = <&dsi_out>;
+			};
+		};
+	};
+};
+
+&ltdc {
+	status = "okay";
+
+	port {
+		ltdc_out_dsi: endpoint {
+			remote-endpoint = <&dsi_in>;
+		};
+	};
+};