ASoC: tas2562: Add right and left channel slot programming
PATCH 1/4 ASoC: tas2562: Add right and left channel slot programming
Add programming for the tdm slots for the right and left. This also requires configuring the RX/TX offsets for the DAI format type.
--- sound/soc/codecs/tas2562.c | 71 +++++++++++++++++++++++++++++--------- sound/soc/codecs/tas2562.h | 5 ++- 2 files changed, 59 insertions(+), 17 deletions(-)
sound/soc/codecs/tas2562.c +55 -16
@@ -175,7 +175,37 @@ static int tas2562_set_dai_tdm_slot(struct snd_soc_dai *dai, {struct snd_soc_component *component = dai->component;struct tas2562_data *tas2562 =snd_soc_component_get_drvdata (component); -int ret =0 ; +int left_slot, right_slot; +int slots_cfg; +int ret; + +if (!tx_mask) { +dev_err (component->dev,"tx masks must not be 0\n" ); +return -EINVAL ; + } + +if (slots ==1 ) { +if (tx_mask !=1 ) +return -EINVAL ; + + left_slot =0 ; + right_slot =0 ; + }else { + left_slot =__ffs (tx_mask); + tx_mask &= ~(1 << left_slot); +if (tx_mask ==0 ) { + right_slot = left_slot; + }else { + right_slot =__ffs (tx_mask); + tx_mask &= ~(1 << right_slot); + } + } + + slots_cfg = (right_slot <<TAS2562_RIGHT_SLOT_SHIFT ) | left_slot; + + ret =snd_soc_component_write (component,TAS2562_TDM_CFG3 , slots_cfg); +if (ret <0 ) +return ret;switch (slot_width) {case 16 :
@@ -208,6 +238,18 @@ static int tas2562_set_dai_tdm_slot(struct snd_soc_dai *dai,if (ret <0 )return ret; + ret =snd_soc_component_update_bits (component,TAS2562_TDM_CFG5 , +TAS2562_TDM_CFG5_VSNS_SLOT_MASK , + tas2562->v_sense_slot); +if (ret <0 ) +return ret; + + ret =snd_soc_component_update_bits (component,TAS2562_TDM_CFG6 , +TAS2562_TDM_CFG6_ISNS_SLOT_MASK , + tas2562->i_sense_slot); +if (ret <0 ) +return ret; +return 0 ; }
@@ -285,7 +327,8 @@ static int tas2562_set_dai_fmt(struct snd_soc_dai *dai, unsigned int fmt) {struct snd_soc_component *component = dai->component;struct tas2562_data *tas2562 =snd_soc_component_get_drvdata (component); -u8 tdm_rx_start_slot =0 , asi_cfg_1 =0 ; +u8 asi_cfg_1 =0 ; +u8 tdm_rx_start_slot =0 ;int ret;switch (fmt &SND_SOC_DAIFMT_INV_MASK ) {
@@ -307,27 +350,23 @@ static int tas2562_set_dai_fmt(struct snd_soc_dai *dai, unsigned int fmt)dev_err (tas2562->dev,"Failed to set RX edge\n" );return ret; } -switch (fmt &SND_SOC_DAIFMT_FORMAT_MASK ) { -case (SND_SOC_DAIFMT_I2S ): -case (SND_SOC_DAIFMT_DSP_A ): -case (SND_SOC_DAIFMT_DSP_B ): - tdm_rx_start_slot =BIT (1 ); -break ; -case (SND_SOC_DAIFMT_LEFT_J ): +case SND_SOC_DAIFMT_LEFT_J : +case SND_SOC_DAIFMT_DSP_B : tdm_rx_start_slot =0 ;break ; -default : -dev_err (tas2562->dev,"DAI Format is not found, fmt=0x%x\n" , - fmt); - ret = -EINVAL ; +case SND_SOC_DAIFMT_I2S : +case SND_SOC_DAIFMT_DSP_A : + tdm_rx_start_slot =1 ;break ; +default : +dev_err (tas2562->dev, +"DAI Format is not found, fmt=0x%x\n" , fmt); +return -EINVAL ; } ret =snd_soc_component_update_bits (component,TAS2562_TDM_CFG1 , -TAS2562_TDM_CFG1_RX_OFFSET_MASK , - tdm_rx_start_slot); - +TAS2562_RX_OFF_MASK , (tdm_rx_start_slot <<1 ));if (ret <0 )return ret;
sound/soc/codecs/tas2562.h +4 -1
@@ -34,6 +34,10 @@#define TAS2562_TDM_DET TAS2562_REG(0, 0x11)#define TAS2562_REV_ID TAS2562_REG(0, 0x7d) +#define TAS2562_RX_OFF_MASK GENMASK(5, 1) +#define TAS2562_TX_OFF_MASK GENMASK(3, 1) +#define TAS2562_RIGHT_SLOT_SHIFT 4 +/* Page 2 */ #define TAS2562_DVC_CFG1 TAS2562_REG(2, 0x0c)#define TAS2562_DVC_CFG2 TAS2562_REG(2, 0x0d)
@@ -49,7 +53,6 @@#define TAS2562_TDM_CFG1_RX_EDGE_MASK BIT(0)#define TAS2562_TDM_CFG1_RX_FALLING 1 -#define TAS2562_TDM_CFG1_RX_OFFSET_MASK GENMASK(4, 0)#define TAS2562_TDM_CFG0_RAMPRATE_MASK BIT(5)#define TAS2562_TDM_CFG0_RAMPRATE_44_1 BIT(5)
Signature · 1 line
2.26.2
PATCH 2/4 dt-bindings: tas2562: Add voltage sense slot property
Add a property to configure the slot for the voltage sense monitoring of the device. Vsense data will be sent to the processor via the slot defined by the property
--- Documentation/devicetree/bindings/sound/tas2562.txt | 3 +++ 1 file changed, 3 insertions(+)
Documentation/devicetree/bindings/sound/tas2562.txt +3 -0
@@ -11,6 +11,8 @@ Required properties: - compatible: - Should contain "ti,tas2562", "ti,tas2563". - reg: - The i2c address. Should be 0x4c, 0x4d, 0x4e or 0x4f. - ti,imon-slot-no:- TDM TX current sense time slot. + - ti,vmon-slot-no:- TDM TX voltage sense time slot. This slot must always be + greater then ti,imon-slot-no. Optional properties: - interrupt-parent: phandle to the interrupt controller which provides
@@ -30,5 +32,6 @@ tas2562@4c { shut-down-gpio = <&gpio1 15 0>; ti,imon-slot-no = <0>; + ti,vmon-slot-no = <1>; };
Signature · 1 line
2.26.2
PATCH 3/4 ASoC: tas2562: Add voltage sense slot configuration
In reply to Dan MurphyAdd Vsense slot configuration based on the device tree. Adding this property enables the slot programming to be moved to the tdm_set_slot callback. This in affect sets the slots for the Isense and Vsense and enabling this these modes are now based on whether these features were powered on or not.
--- sound/soc/codecs/tas2562.c | 65 ++++++++++++++++++++++++++++++-------- 1 file changed, 51 insertions(+), 14 deletions(-)
sound/soc/codecs/tas2562.c +51 -14
@@ -250,12 +250,26 @@ static int tas2562_set_dai_tdm_slot(struct snd_soc_dai *dai,if (ret <0 )return ret; + ret =snd_soc_component_update_bits (component,TAS2562_TDM_CFG5 , +TAS2562_TDM_CFG5_VSNS_SLOT_MASK , + tas2562->v_sense_slot); +if (ret <0 ) +return ret; + + ret =snd_soc_component_update_bits (component,TAS2562_TDM_CFG6 , +TAS2562_TDM_CFG6_ISNS_SLOT_MASK , + tas2562->i_sense_slot); +if (ret <0 ) +return ret; +return 0 ; }static int tas2562_set_bitwidth (struct tas2562_data *tas2562,int bitwidth) {int ret; +int val; +int sense_en;switch (bitwidth) {case SNDRV_PCM_FORMAT_S16_LE :
@@ -263,21 +277,18 @@ static int tas2562_set_bitwidth(struct tas2562_data *tas2562, int bitwidth)TAS2562_TDM_CFG2 ,TAS2562_TDM_CFG2_RXWLEN_MASK , TAS2562_TDM_CFG2_RXWLEN_16B); - tas2562->v_sense_slot = tas2562->i_sense_slot +2 ;break ;case SNDRV_PCM_FORMAT_S24_LE :snd_soc_component_update_bits (tas2562->component,TAS2562_TDM_CFG2 ,TAS2562_TDM_CFG2_RXWLEN_MASK ,TAS2562_TDM_CFG2_RXWLEN_24B ); - tas2562->v_sense_slot = tas2562->i_sense_slot +4 ;break ;case SNDRV_PCM_FORMAT_S32_LE :snd_soc_component_update_bits (tas2562->component,TAS2562_TDM_CFG2 ,TAS2562_TDM_CFG2_RXWLEN_MASK ,TAS2562_TDM_CFG2_RXWLEN_32B ); - tas2562->v_sense_slot = tas2562->i_sense_slot +4 ;break ;default :
@@ -285,17 +296,27 @@ static int tas2562_set_bitwidth(struct tas2562_data *tas2562, int bitwidth)return -EINVAL ; } - ret =snd_soc_component_update_bits (tas2562->component, -TAS2562_TDM_CFG5 , -TAS2562_TDM_CFG5_VSNS_EN |TAS2562_TDM_CFG5_VSNS_SLOT_MASK , -TAS2562_TDM_CFG5_VSNS_EN | tas2562->v_sense_slot); + val =snd_soc_component_read (tas2562->component,TAS2562_PWR_CTRL ); +if (val <0 ) +return val; + +if (val & (1 <<TAS2562_VSENSE_POWER_EN )) + sense_en =0 ; +else + sense_en =TAS2562_TDM_CFG5_VSNS_EN ; + + ret =snd_soc_component_update_bits (tas2562->component,TAS2562_TDM_CFG5 , +TAS2562_TDM_CFG5_VSNS_EN , sense_en);if (ret <0 )return ret; - ret =snd_soc_component_update_bits (tas2562->component, -TAS2562_TDM_CFG6 , -TAS2562_TDM_CFG6_ISNS_EN |TAS2562_TDM_CFG6_ISNS_SLOT_MASK , -TAS2562_TDM_CFG6_ISNS_EN | tas2562->i_sense_slot); +if (val & (1 <<TAS2562_ISENSE_POWER_EN )) + sense_en =0 ; +else + sense_en =TAS2562_TDM_CFG6_ISNS_EN ; + + ret =snd_soc_component_update_bits (tas2562->component,TAS2562_TDM_CFG6 , +TAS2562_TDM_CFG6_ISNS_EN , sense_en);if (ret <0 )return ret;
@@ -669,9 +690,25 @@ static int tas2562_parse_dt(struct tas2562_data *tas2562) ret =fwnode_property_read_u32 (dev->fwnode,"ti,imon-slot-no" , &tas2562->i_sense_slot); -if (ret) -dev_err (dev,"Looking up %s property failed %d\n" , -"ti,imon-slot-no" , ret); +if (ret) { +dev_err (dev,"Property %s is missing setting default slot\n" , +"ti,imon-slot-no" ); + tas2562->i_sense_slot =0 ; + } + + + ret =fwnode_property_read_u32 (dev->fwnode,"ti,vmon-slot-no" , + &tas2562->v_sense_slot); +if (ret) { +dev_info (dev,"Property %s is missing setting default slot\n" , +"ti,vmon-slot-no" ); + tas2562->v_sense_slot =2 ; + } + +if (tas2562->v_sense_slot < tas2562->i_sense_slot) { +dev_err (dev,"Vsense slot must be greater than Isense slot\n" ); +return -EINVAL ; + }return ret; }
Signature · 1 line
2.26.2
PATCH 4/4 dt-bindings: tas2562: Convert the tas2562 binding to yaml
In reply to Dan MurphyConvert the TAS2562 text file to yaml format.
--- .../devicetree/bindings/sound/tas2562.txt | 37 --------- .../devicetree/bindings/sound/tas2562.yaml | 77 +++++++++++++++++++ 2 files changed, 77 insertions(+), 37 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sound/tas2562.txt create mode 100644 Documentation/devicetree/bindings/sound/tas2562.yaml
Documentation/devicetree/bindings/sound/tas2562.txt deleted +0 -37
@@ -1,37 +0,0 @@ -Texas Instruments TAS2562 Smart PA - -The TAS2562 is a mono, digital input Class-D audio amplifier optimized for -efficiently driving high peak power into small loudspeakers. -Integrated speaker voltage and current sense provides for -real time monitoring of loudspeaker behavior. - -Required properties: - - #address-cells - Should be <1>. - - #size-cells - Should be <0>. - - compatible: - Should contain "ti,tas2562", "ti,tas2563". - - reg: - The i2c address. Should be 0x4c, 0x4d, 0x4e or 0x4f. - - ti,imon-slot-no:- TDM TX current sense time slot. - - ti,vmon-slot-no:- TDM TX voltage sense time slot. This slot must always be - greater then ti,imon-slot-no. - -Optional properties: -- interrupt-parent: phandle to the interrupt controller which provides - the interrupt. -- interrupts: (GPIO) interrupt to which the chip is connected. -- shut-down-gpio: GPIO used to control the state of the device. - -Examples: -tas2562@4c { - #address-cells = <1>; - #size-cells = <0>; - compatible = "ti,tas2562"; - reg = <0x4c>; - - interrupt-parent = <&gpio1>; - interrupts = <14>; - - shut-down-gpio = <&gpio1 15 0>; - ti,imon-slot-no = <0>; - ti,vmon-slot-no = <1>; -}; -
Documentation/devicetree/bindings/sound/tas2562.yaml new file +77 -0
77 lines not on this page · raw message
Signature · 1 line
2.26.2
Rob Herring
maintainerRe: [PATCH 4/4] dt-bindings: tas2562: Convert the tas2562 binding to yaml
Quoted 59 lines · Dan Murphy
Convert the TAS2562 text file to yaml format.
Signed-off-by Dan Murphy <[email protected]>--- .../devicetree/bindings/sound/tas2562.txt | 37 --------- .../devicetree/bindings/sound/tas2562.yaml | 77 +++++++++++++++++++ 2 files changed, 77 insertions(+), 37 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sound/tas2562.txt create mode 100644 Documentation/devicetree/bindings/sound/tas2562.yamlDocumentation/devicetree/bindings/sound/tas2562.txt deleted +0
-37@@ -1,37 +0,0 @@ -Texas Instruments TAS2562 Smart PA - -The TAS2562 is a mono, digital input Class-D audio amplifier optimized for -efficiently driving high peak power into small loudspeakers. -Integrated speaker voltage and current sense provides for -real time monitoring of loudspeaker behavior. - -Required properties: - - #address-cells - Should be <1>. - - #size-cells - Should be <0>. - - compatible: - Should contain "ti,tas2562", "ti,tas2563". - - reg: - The i2c address. Should be 0x4c, 0x4d, 0x4e or 0x4f. - - ti,imon-slot-no:- TDM TX current sense time slot. - - ti,vmon-slot-no:- TDM TX voltage sense time slot. This slot must always be - greater then ti,imon-slot-no. - -Optional properties: -- interrupt-parent: phandle to the interrupt controller which provides - the interrupt. -- interrupts: (GPIO) interrupt to which the chip is connected. -- shut-down-gpio: GPIO used to control the state of the device. - -Examples: -tas2562@4c { - #address-cells = <1>; - #size-cells = <0>; - compatible = "ti,tas2562"; - reg = <0x4c>; - - interrupt-parent = <&gpio1>; - interrupts = <14>; - - shut-down-gpio = <&gpio1 15 0>; - ti,imon-slot-no = <0>; - ti,vmon-slot-no = <1>; -}; -Documentation/devicetree/bindings/sound/tas2562.yaml new file +0
-0
Documentation/devicetree/bindings/sound/tas2562.yaml line 1
Quoted 1 line
Documentation/devicetree/bindings/sound/tas2562.yaml new file +1
-0@@ -0,0 +1,77 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause)
Same licensing comment here as tas2770
Quoted 21 lines
Documentation/devicetree/bindings/sound/tas2562.yaml new file +21
-0+# Copyright (C) 2019 Texas Instruments Incorporated +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/sound/tas2562.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Texas Instruments TAS2562 Smart PA + +maintainers: + - Dan Murphy <[email protected]> + +description: | + The TAS2562 is a mono, digital input Class-D audio amplifier optimized for + efficiently driving high peak power into small loudspeakers. + Integrated speaker voltage and current sense provides for + real time monitoring of loudspeaker behavior. + +properties: + compatible: + enum: + - ti,tas2562
Documentation/devicetree/bindings/sound/tas2562.yaml line 32
Quoted 10 lines
Documentation/devicetree/bindings/sound/tas2562.yaml new file +10
-0+ - ti,tas2563 + + reg: + maxItems: 1 + description: | + I2C address of the device can be one of these 0x4c, 0x4d, 0x4e or 0x4f + + shut-down-gpio: + description: GPIO used to control the state of the device. + deprecated: true
Why do we need this as the driver never worked?
Documentation/devicetree/bindings/sound/tas2562.yaml line 35
Quoted 3 lines
Documentation/devicetree/bindings/sound/tas2562.yaml new file +3
-0+ + shutdown-gpio: + description: GPIO used to control the state of the device.
-gpios is the preferred form: shutdown-gpios
Quoted 45 lines
Documentation/devicetree/bindings/sound/tas2562.yaml new file +42
-0+ + interrupts: + maxItems: 1 + + ti,imon-slot-no: + $ref: /schemas/types.yaml#/definitions/uint32 + description: TDM TX current sense time slot. + + ti,vmon-slot-no: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + TDM TX voltage sense time slot. This slot must always be greater then + ti,imon-slot-no. + + '#sound-dai-cells': + const: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + codec: codec@4c { + compatible = "ti,tas2562"; + reg = <0x4c>; + #sound-dai-cells = <1>; + interrupt-parent = <&gpio1>; + interrupts = <14>; + shutdown-gpio = <&gpio1 15 0>; + ti,imon-slot-no = <0>; + ti,vmon-slot-no = <2>; + }; + }; + +...Signature · 1 line
2.26.2
Re: [PATCH 4/4] dt-bindings: tas2562: Convert the tas2562 binding to yaml
Rob
Quoted 54 lines · Rob Herring
Quoted 53 lines · Dan Murphy
Convert the TAS2562 text file to yaml format.
Signed-off-by Dan Murphy <[email protected]>--- .../devicetree/bindings/sound/tas2562.txt | 37 --------- .../devicetree/bindings/sound/tas2562.yaml | 77 +++++++++++++++++++ 2 files changed, 77 insertions(+), 37 deletions(-)delete mode 100644
Documentation/devicetree/bindings/sound/tas2562.txtcreate mode 100644Documentation/devicetree/bindings/sound/tas2562.yamlDocumentation/devicetree/bindings/sound/tas2562.txt deleted +0
-37@@ -1,37 +0,0 @@ -Texas Instruments TAS2562 Smart PA - -The TAS2562 is a mono, digital input Class-D audio amplifier optimized for -efficiently driving high peak power into small loudspeakers. -Integrated speaker voltage and current sense provides for -real time monitoring of loudspeaker behavior. - -Required properties: - - #address-cells - Should be <1>. - - #size-cells - Should be <0>. - - compatible: - Should contain "ti,tas2562", "ti,tas2563". - - reg: - The i2c address. Should be 0x4c, 0x4d, 0x4e or 0x4f. - - ti,imon-slot-no:- TDM TX current sense time slot. - - ti,vmon-slot-no:- TDM TX voltage sense time slot. This slot must always be - greater then ti,imon-slot-no. - -Optional properties: -- interrupt-parent: phandle to the interrupt controller which provides - the interrupt. -- interrupts: (GPIO) interrupt to which the chip is connected. -- shut-down-gpio: GPIO used to control the state of the device. - -Examples: -tas2562@4c { - #address-cells = <1>; - #size-cells = <0>; - compatible = "ti,tas2562"; - reg = <0x4c>; - - interrupt-parent = <&gpio1>; - interrupts = <14>; - - shut-down-gpio = <&gpio1 15 0>; - ti,imon-slot-no = <0>; - ti,vmon-slot-no = <1>; -}; -
Quoted 8 lines
Documentation/devicetree/bindings/sound/tas2562.yaml line 1
Quoted 7 lines
Documentation/devicetree/bindings/sound/tas2562.yaml new file +1
-0@@ -0,0 +1,77 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause)Same licensing comment here as tas2770
OK I will fix it like I did with the other TAS2770 patches
Quoted 24 lines
Quoted 24 lines
Documentation/devicetree/bindings/sound/tas2562.yaml new file +24
-0+# Copyright (C) 2019 Texas Instruments Incorporated +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/sound/tas2562.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Texas Instruments TAS2562 Smart PA + +maintainers: + - Dan Murphy <[email protected]> + +description: | + The TAS2562 is a mono, digital input Class-D audio amplifier optimized for + efficiently driving high peak power into small loudspeakers. + Integrated speaker voltage and current sense provides for + real time monitoring of loudspeaker behavior. + +properties: + compatible: + enum: + - ti,tas2562 + - ti,tas2563 + + reg:
Quoted 8 lines
Documentation/devicetree/bindings/sound/tas2562.yaml line 32
Quoted 7 lines
Documentation/devicetree/bindings/sound/tas2562.yaml new file +7
-0+ maxItems: 1 + description: | + I2C address of the device can be one of these 0x4c, 0x4d, 0x4e or 0x4f + + shut-down-gpio: + description: GPIO used to control the state of the device. + deprecated: trueWhy do we need this as the driver never worked?
Not sure what you are asking.
Driver has been fixed for this specific binding in sound for-next.
Quoted 5 lines
Documentation/devicetree/bindings/sound/tas2562.yaml line 35
Quoted 4 lines
Documentation/devicetree/bindings/sound/tas2562.yaml new file +3
-0+ + shutdown-gpio: + description: GPIO used to control the state of the device.-gpios is the preferred form: shutdown-gpios
So the plural form of gpio is preferred even if the gpio is singular? I would think gpio would be plural if this was an array of gpios.
I am waiting for the yaml to be accepted before adding this shutdown property to the driver.
Dan
Rob Herring
maintainerRe: [PATCH 4/4] dt-bindings: tas2562: Convert the tas2562 binding to yaml
Quoted 103 lines · Dan Murphy
Rob
Quoted 54 lines · Rob Herring
Quoted 53 lines · Dan Murphy
Convert the TAS2562 text file to yaml format.
Signed-off-by Dan Murphy <[email protected]>--- .../devicetree/bindings/sound/tas2562.txt | 37 --------- .../devicetree/bindings/sound/tas2562.yaml | 77 +++++++++++++++++++ 2 files changed, 77 insertions(+), 37 deletions(-)delete mode 100644
Documentation/devicetree/bindings/sound/tas2562.txtcreate mode 100644Documentation/devicetree/bindings/sound/tas2562.yamlDocumentation/devicetree/bindings/sound/tas2562.txt deleted +0
-37@@ -1,37 +0,0 @@ -Texas Instruments TAS2562 Smart PA - -The TAS2562 is a mono, digital input Class-D audio amplifier optimized for -efficiently driving high peak power into small loudspeakers. -Integrated speaker voltage and current sense provides for -real time monitoring of loudspeaker behavior. - -Required properties: - - #address-cells - Should be <1>. - - #size-cells - Should be <0>. - - compatible: - Should contain "ti,tas2562", "ti,tas2563". - - reg: - The i2c address. Should be 0x4c, 0x4d, 0x4e or 0x4f. - - ti,imon-slot-no:- TDM TX current sense time slot. - - ti,vmon-slot-no:- TDM TX voltage sense time slot. This slot must always be - greater then ti,imon-slot-no. - -Optional properties: -- interrupt-parent: phandle to the interrupt controller which provides - the interrupt. -- interrupts: (GPIO) interrupt to which the chip is connected. -- shut-down-gpio: GPIO used to control the state of the device. - -Examples: -tas2562@4c { - #address-cells = <1>; - #size-cells = <0>; - compatible = "ti,tas2562"; - reg = <0x4c>; - - interrupt-parent = <&gpio1>; - interrupts = <14>; - - shut-down-gpio = <&gpio1 15 0>; - ti,imon-slot-no = <0>; - ti,vmon-slot-no = <1>; -}; -Quoted 8 lines
Documentation/devicetree/bindings/sound/tas2562.yaml line 1
Quoted 7 lines
Documentation/devicetree/bindings/sound/tas2562.yaml new file +1
-0@@ -0,0 +1,77 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause)Same licensing comment here as tas2770
OK I will fix it like I did with the other TAS2770 patches
Quoted 24 lines
Quoted 24 lines
Documentation/devicetree/bindings/sound/tas2562.yaml new file +24
-0+# Copyright (C) 2019 Texas Instruments Incorporated +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/sound/tas2562.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Texas Instruments TAS2562 Smart PA + +maintainers: + - Dan Murphy <[email protected]> + +description: | + The TAS2562 is a mono, digital input Class-D audio amplifier optimized for + efficiently driving high peak power into small loudspeakers. + Integrated speaker voltage and current sense provides for + real time monitoring of loudspeaker behavior. + +properties: + compatible: + enum: + - ti,tas2562 + - ti,tas2563 + + reg:Quoted 8 lines
Documentation/devicetree/bindings/sound/tas2562.yaml line 32
Quoted 7 lines
Documentation/devicetree/bindings/sound/tas2562.yaml new file +7
-0+ maxItems: 1 + description: | + I2C address of the device can be one of these 0x4c, 0x4d, 0x4e or 0x4f + + shut-down-gpio: + description: GPIO used to control the state of the device. + deprecated: trueWhy do we need this as the driver never worked?
Quoted 5 lines
Not sure what you are asking.
Driver has been fixed for this specific binding in sound for-next.
Why fix the driver and then have to maintain compatibility? Just update everything to use 'shutdown-gpios' and move on.
Rob
Mark Brown
maintainerQuoted 2 lines · Dan Murphy
Add programming for the tdm slots for the right and left. This also requires configuring the RX/TX offsets for the DAI format type.
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next
Thanks!
[1/3] ASoC: tas2562: Add right and left channel slot programming
commit: d7bd40ae55ce339a3c9be7fc2087c671d3d80894
[2/3] ASoC: tas2562: Add voltage sense slot property
commit: f10b6c99c08433861d1ed62267fa57ced7dbdf50
[3/3] ASoC: tas2562: Add voltage sense slot configuration
commit: 09ed395b05feb7d0f77ab52c48d2f77c1b44d2abAll being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark