Skip to contentSkip to conversation

arm: Add extra boot device (UART) to run Ymodem u-boot.img boot on XEA (imx28)

PATCH New Lukasz Majewski 3 participants 3 messages Jul 10, 2020 – Jul 16, 2020 Arm i.MX and Layerscape

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 arm: Add extra boot device (UART) to run Ymodem u-boot.img boot on XEA (imx28)

This commit enables imx28 based XEA board's u-boot.sb (SPL) to download u-boot proper (u-boot.img) via Ymodem protocol.

This is extremely useful in the recovery scenario where u-boot.sb is downloaded via uuu utility to SDRAM [*], and then one can upload u-boot proper via serial console to fully debrick the device.

Note - debricking procedure of imx28 devices:
- NXP's original USB based tools (like mxsldr or uuu) expect single u-boot.sb which is a relic of the old U-Boot (~2013) without SPL and U-Boot proper distinction.

[*] On Host:
------------
cat << EOF > imx28_xea.lst
uuu_version 1.3.0
SDPS: boot -f /srv/tftp/xea/u-boot.sb
SDPU: done
EOF

Please start picocom:
sudo picocom -b 115200 -s "sz -vv" /dev/ttyUSB1
sudo ./uuu/uuu -V imx28_xea.lst

On the U-boot console one shall see:
Trying to boot from UART
CCC

Then please press CTRL+A, S
and type u-boot.img

---

 board/liebherr/xea/xea.c    | 1 +
 configs/imx28_xea_defconfig | 1 +
 2 files changed, 2 insertions(+)
board/liebherr/xea/xea.c +1 -0
index 8159f3a2d9..4062c6fb82 100644
@@ -116,6 +116,7 @@ void board_boot_order(u32 *spl_boot_list)
 {
 	spl_boot_list[0] = BOOT_DEVICE_MMC1;
 	spl_boot_list[1] = BOOT_DEVICE_SPI;
+	spl_boot_list[2] = BOOT_DEVICE_UART;
 }
 
 int spl_start_uboot(void)
configs/imx28_xea_defconfig +1 -0
index b879de5042..38f3fa6871 100644
@@ -36,6 +36,7 @@ CONFIG_SPL_MMC_TINY=y
 CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SPL_OS_BOOT=y
 CONFIG_SPL_SPI_LOAD=y
+CONFIG_SPL_YMODEM_SUPPORT=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_SPL=y
 CONFIG_CMD_ASKENV=y
Signature · 1 line
2.20.1
#1 lore raw

PATCH 1/1 arm: Add extra boot device (UART) to run Ymodem u-boot.img boot on XEA (imx28)

Quoted 31 lines

Subject: [PATCH] arm: Add extra boot device (UART) to run Ymodem u-boot.img boot on XEA (imx28)

This commit enables imx28 based XEA board's u-boot.sb (SPL) to download u-boot proper (u-boot.img) via Ymodem protocol.

This is extremely useful in the recovery scenario where u-boot.sb is downloaded via uuu utility to SDRAM [*], and then one can upload u-boot proper via serial console to fully debrick the device.

Note - debricking procedure of imx28 devices:
- NXP's original USB based tools (like mxsldr or uuu) expect single u-boot.sb which is a relic of the old U-Boot (~2013) without SPL and U-Boot proper distinction.

[*] On Host:
------------
cat << EOF > imx28_xea.lst
uuu_version 1.3.0
SDPS: boot -f /srv/tftp/xea/u-boot.sb
SDPU: done
EOF

Please start picocom:
sudo picocom -b 115200 -s "sz -vv" /dev/ttyUSB1 sudo ./uuu/uuu -V imx28_xea.lst

On the U-boot console one shall see:
Trying to boot from UART
CCC

Quoted 5 lines

Then please press CTRL+A, S
and type u-boot.img

Quoted 31 lines

---

 board/liebherr/xea/xea.c    | 1 +
 configs/imx28_xea_defconfig | 1 +
 2 files changed, 2 insertions(+)
board/liebherr/xea/xea.c index renamed from board/liebherr/xea/xea.c +0 -0

8159f3a2d9..4062c6fb82 100644

board/liebherr/xea/xea.c +1 -0
@@ -116,6 +116,7 @@ void board_boot_order(u32 *spl_boot_list)  {
 	spl_boot_list[0] = BOOT_DEVICE_MMC1;
 	spl_boot_list[1] = BOOT_DEVICE_SPI;
+	spl_boot_list[2] = BOOT_DEVICE_UART;
 }
 
 int spl_start_uboot(void)
configs/imx28_xea_defconfig index renamed from configs/imx28_xea_defconfig +0 -0

b879de5042..38f3fa6871 100644

configs/imx28_xea_defconfig +1 -1
@@ -36,6 +36,7 @@ CONFIG_SPL_MMC_TINY=y
 CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SPL_OS_BOOT=y
 CONFIG_SPL_SPI_LOAD=y
+CONFIG_SPL_YMODEM_SUPPORT=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_SPL=y
 CONFIG_CMD_ASKENV=y
--

2.20.1

#2 lore raw

PATCH 1/1 arm: Add extra boot device (UART) to run Ymodem u-boot.img boot on XEA (imx28)

In reply to Lukasz Majewski
Quoted 24 lines

This commit enables imx28 based XEA board's u-boot.sb (SPL) to download u-boot proper (u-boot.img) via Ymodem protocol.
This is extremely useful in the recovery scenario where u-boot.sb is downloaded via uuu utility to SDRAM [*], and then one can upload u-boot proper via serial console to fully debrick the device.
Note - debricking procedure of imx28 devices:
- NXP's original USB based tools (like mxsldr or uuu) expect single u-boot.sb which is a relic of the old U-Boot (~2013) without SPL and U-Boot proper distinction.
[*] On Host:
------------
cat << EOF > imx28_xea.lst
uuu_version 1.3.0
SDPS: boot -f /srv/tftp/xea/u-boot.sb
SDPU: done
EOF
Please start picocom:
sudo picocom -b 115200 -s "sz -vv" /dev/ttyUSB1
sudo ./uuu/uuu -V imx28_xea.lst
On the U-boot console one shall see:
Trying to boot from UART
CCC
Then please press CTRL+A, S
and type u-boot.img

Quoted 2 lines

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================