Skip to contentSkip to conversation

Kconfig: Introduce CONFIG_SYS_HAS_SRAM

PATCH Superseded Ovidiu Panait 3 participants 29 messages Jul 20, 2020 – Jul 29, 2020

Subsystems (5)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/17 Kconfig: Introduce CONFIG_SYS_HAS_SRAM

In order to be able to replace "#ifdef CONFIG_SYS_SRAM_BASE" sequences with the IS_ENABLED() equivalent, introduce a new boolean Kconfig option that signals whether the platform has SRAM support.

---

 Kconfig | 11 +++++++++++
 1 file changed, 11 insertions(+)
Kconfig +11 -0
index 566ca72c92..934c020a2f 100644
@@ -350,6 +350,17 @@ config PLATFORM_ELFENTRY
 	default "__start" if MIPS
 	default "_start"
 
+config SYS_HAS_SRAM
+	bool
+	default y if TARGET_PIC32MZDASK
+	default y if TARGET_DEVKIT8000
+	default y if TARGET_TRICORDER
+	default n
+	help
+	  Enable this to allow support for the on board SRAM.
+	  SRAM base address is controlled by CONFIG_SYS_SRAM_BASE.
+	  SRAM size is controlled by CONFIG_SYS_SRAM_SIZE.
+
 endmenu		# General setup
 
 menu "Boot images"
Signature · 1 line
2.17.1
#1 lore raw

PATCH v3 2/17 Kconfig: Convert CONFIG_SYS_SRAM_BASE to Kconfig

This converts ad-hoc CONFIG_SYS_SRAM_BASE to Kconfig.

---

 Kconfig                       | 5 +++++
 include/configs/pic32mzdask.h | 1 -
 scripts/config_whitelist.txt  | 1 -
 3 files changed, 5 insertions(+), 2 deletions(-)
Kconfig +5 -0
index 934c020a2f..4ff1000848 100644
@@ -361,6 +361,11 @@ config SYS_HAS_SRAM
 	  SRAM base address is controlled by CONFIG_SYS_SRAM_BASE.
 	  SRAM size is controlled by CONFIG_SYS_SRAM_SIZE.
 
+config SYS_SRAM_BASE
+	hex
+	default 0x80000000 if TARGET_PIC32MZDASK
+	default 0x0
+
 endmenu		# General setup
 
 menu "Boot images"
include/configs/pic32mzdask.h +0 -1
index 73edd28f1a..25b898f2e6 100644
@@ -19,7 +19,6 @@
 /*----------------------------------------------------------------------
  * Memory Layout
  */
-#define CONFIG_SYS_SRAM_BASE		0x80000000
 #define CONFIG_SYS_SRAM_SIZE		0x00080000 /* 512K */
 
 /* Initial RAM for temporary stack, global data */
scripts/config_whitelist.txt +0 -1
index 2ec7642583..93233f066b 100644
@@ -3788,7 +3788,6 @@ CONFIG_SYS_SPL_LEN
 CONFIG_SYS_SPL_MALLOC_SIZE
 CONFIG_SYS_SPL_MALLOC_START
 CONFIG_SYS_SPR
-CONFIG_SYS_SRAM_BASE
 CONFIG_SYS_SRAM_SIZE
 CONFIG_SYS_SRAM_START
 CONFIG_SYS_SRIO
Signature · 1 line
2.17.1
#2 lore raw

PATCH v3 3/17 Kconfig: Convert CONFIG_SYS_SRAM_SIZE to Kconfig

In reply to Ovidiu Panait

This converts ad-hoc CONFIG_SYS_SRAM_SIZE to Kconfig.

---

 Kconfig                       | 7 +++++++
 include/configs/devkit8000.h  | 1 -
 include/configs/pic32mzdask.h | 2 --
 include/configs/tricorder.h   | 1 -
 scripts/config_whitelist.txt  | 1 -
 5 files changed, 7 insertions(+), 5 deletions(-)
Kconfig +7 -0
index 4ff1000848..d0f7ff80d1 100644
@@ -366,6 +366,13 @@ config SYS_SRAM_BASE
 	default 0x80000000 if TARGET_PIC32MZDASK
 	default 0x0
 
+config SYS_SRAM_SIZE
+	hex
+	default 0x00080000 if TARGET_PIC32MZDASK
+	default 0x10000 if TARGET_DEVKIT8000
+	default 0x10000 if TARGET_TRICORDER
+	default 0x0
+
 endmenu		# General setup
 
 menu "Boot images"
include/configs/devkit8000.h +0 -1
index f90c1c5a18..cdf7d7aa21 100644
@@ -140,7 +140,6 @@
 
 /* SRAM config */
 #define CONFIG_SYS_SRAM_START              0x40200000
-#define CONFIG_SYS_SRAM_SIZE               0x10000
 
 /* Defines for SPL */
 
include/configs/pic32mzdask.h +0 -2
index 25b898f2e6..d50edc7715 100644
@@ -19,8 +19,6 @@
 /*----------------------------------------------------------------------
  * Memory Layout
  */
-#define CONFIG_SYS_SRAM_SIZE		0x00080000 /* 512K */
-
 /* Initial RAM for temporary stack, global data */
 #define CONFIG_SYS_INIT_RAM_SIZE	0x10000
 #define CONFIG_SYS_INIT_RAM_ADDR	\
include/configs/tricorder.h +0 -1
index 83aa3cd468..d438a7e635 100644
@@ -202,7 +202,6 @@
 
 /* SRAM config */
 #define CONFIG_SYS_SRAM_START		0x40200000
-#define CONFIG_SYS_SRAM_SIZE		0x10000
 
 /* Defines for SPL */
 
scripts/config_whitelist.txt +0 -1
index 93233f066b..392b50875f 100644
@@ -3788,7 +3788,6 @@ CONFIG_SYS_SPL_LEN
 CONFIG_SYS_SPL_MALLOC_SIZE
 CONFIG_SYS_SPL_MALLOC_START
 CONFIG_SYS_SPR
-CONFIG_SYS_SRAM_SIZE
 CONFIG_SYS_SRAM_START
 CONFIG_SYS_SRIO
 CONFIG_SYS_SRIO1_MEM_BASE
Signature · 1 line
2.17.1
#3 lore raw

PATCH v3 4/17 Kconfig: Remove CONFIG_SYS_SRAM_START

In reply to Ovidiu Panait

Remove ad-hoc CONFIG_SYS_SRAM_START and use CONFIG_SYS_SRAM_BASE instead.

---

 Kconfig                      | 2 ++
 include/configs/devkit8000.h | 3 ---
 include/configs/tricorder.h  | 3 ---
 scripts/config_whitelist.txt | 1 -
 4 files changed, 2 insertions(+), 7 deletions(-)
Kconfig +2 -0
index d0f7ff80d1..b16ee0f57d 100644
@@ -364,6 +364,8 @@ config SYS_HAS_SRAM
 config SYS_SRAM_BASE
 	hex
 	default 0x80000000 if TARGET_PIC32MZDASK
+	default 0x40200000 if TARGET_DEVKIT8000
+	default 0x40200000 if TARGET_TRICORDER
 	default 0x0
 
 config SYS_SRAM_SIZE
include/configs/devkit8000.h +0 -3
index cdf7d7aa21..b4f649a958 100644
@@ -138,9 +138,6 @@
 
 /* Boot Argument Buffer Size */
 
-/* SRAM config */
-#define CONFIG_SYS_SRAM_START              0x40200000
-
 /* Defines for SPL */
 
 /* NAND boot config */
include/configs/tricorder.h +0 -3
index d438a7e635..8ffa39f92f 100644
@@ -200,9 +200,6 @@
 						CONFIG_SYS_INIT_RAM_SIZE - \
 						GENERATED_GBL_DATA_SIZE)
 
-/* SRAM config */
-#define CONFIG_SYS_SRAM_START		0x40200000
-
 /* Defines for SPL */
 
 #define CONFIG_SPL_NAND_BASE
scripts/config_whitelist.txt +0 -1
index 392b50875f..f840a504b6 100644
@@ -3788,7 +3788,6 @@ CONFIG_SYS_SPL_LEN
 CONFIG_SYS_SPL_MALLOC_SIZE
 CONFIG_SYS_SPL_MALLOC_START
 CONFIG_SYS_SPR
-CONFIG_SYS_SRAM_START
 CONFIG_SYS_SRIO
 CONFIG_SYS_SRIO1_MEM_BASE
 CONFIG_SYS_SRIO1_MEM_BUS
Signature · 1 line
2.17.1
#4 lore raw

PATCH v3 5/17 cmd: bdinfo: Move sram info prints to generic code

In reply to Ovidiu Panait

bi_sramstart and bi_sramsize are generic members of the bd_info structure, so move the m68k/powerpc-specific prints to generic code. Also, print them only if SRAM support is enabled via CONFIG_SYS_HAS_SRAM.

---

 arch/m68k/lib/bdinfo.c    | 4 ----
 arch/powerpc/lib/bdinfo.c | 4 ----
 cmd/bdinfo.c              | 4 ++++
 3 files changed, 4 insertions(+), 8 deletions(-)
arch/m68k/lib/bdinfo.c +0 -4
index fb4d1a52fd..b7bc6a3044 100644
@@ -15,10 +15,6 @@ void arch_print_bdinfo(void)
 {
 	struct bd_info *bd = gd->bd;
 
-#if defined(CONFIG_SYS_INIT_RAM_ADDR)
-	bdinfo_print_num("sramstart", (ulong)bd->bi_sramstart);
-	bdinfo_print_num("sramsize", (ulong)bd->bi_sramsize);
-#endif
 	bdinfo_print_mhz("busfreq", bd->bi_busfreq);
 #if defined(CONFIG_SYS_MBAR)
 	bdinfo_print_num("mbar", bd->bi_mbar_base);
arch/powerpc/lib/bdinfo.c +0 -4
index 75611e2592..07f823ee7a 100644
@@ -20,10 +20,6 @@ void arch_print_bdinfo(void)
 {
 	struct bd_info *bd = gd->bd;
 
-#if defined(CONFIG_SYS_INIT_RAM_ADDR)
-	bdinfo_print_num("sramstart", (ulong)bd->bi_sramstart);
-	bdinfo_print_num("sramsize", (ulong)bd->bi_sramsize);
-#endif
 	bdinfo_print_mhz("busfreq", bd->bi_busfreq);
 #if defined(CONFIG_MPC8xx) || defined(CONFIG_E500)
 	bdinfo_print_num("immr_base", bd->bi_immr_base);
cmd/bdinfo.c +4 -0
index 8b2c105e77..7da36f8096 100644
@@ -75,6 +75,10 @@ int do_bdinfo(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])
 	print_bi_dram(bd);
 	bdinfo_print_num("memstart", (ulong)bd->bi_memstart);
 	print_lnum("memsize", (u64)bd->bi_memsize);
+	if (IS_ENABLED(CONFIG_SYS_HAS_SRAM)) {
+		bdinfo_print_num("sramstart", (ulong)bd->bi_sramstart);
+		bdinfo_print_num("sramsize", (ulong)bd->bi_sramsize);
+	}
 	bdinfo_print_num("flashstart", (ulong)bd->bi_flashstart);
 	bdinfo_print_num("flashsize", (ulong)bd->bi_flashsize);
 	bdinfo_print_num("flashoffset", (ulong)bd->bi_flashoffset);
Signature · 1 line
2.17.1
#5 lore raw

PATCH v3 5/17 cmd: bdinfo: Move sram info prints to generic code

Quoted 5 lines · Ovidiu Panait

bi_sramstart and bi_sramsize are generic members of the bd_info structure, so move the m68k/powerpc-specific prints to generic code. Also, print them only if SRAM support is enabled via CONFIG_SYS_HAS_SRAM.

Quoted 8 lines

---

 arch/m68k/lib/bdinfo.c    | 4 ----
 arch/powerpc/lib/bdinfo.c | 4 ----
 cmd/bdinfo.c              | 4 ++++
 3 files changed, 4 insertions(+), 8 deletions(-)
#6 lore raw

PATCH v3 6/17 board_f: Introduce setup_bdinfo initcall

In reply to Ovidiu Panait

Introduce setup_bdinfo initcall as a generic routine to populate bdinfo fields.

---

 common/board_f.c |  6 ++++++
 include/init.h   | 10 ++++++++++
 2 files changed, 16 insertions(+)
common/board_f.c +6 -0
index 88ff0424a7..72446f6da5 100644
@@ -598,6 +598,11 @@ static int display_new_sp(void)
 	return 0;
 }
 
+int setup_bdinfo(void)
+{
+	return 0;
+}
+
 #if defined(CONFIG_M68K) || defined(CONFIG_MIPS) || defined(CONFIG_PPC) || \
 	defined(CONFIG_SH)
 static int setup_board_part1(void)
@@ -975,6 +980,7 @@ static const init_fnc_t init_sequence_f[] = {
 	reserve_stacks,
 	dram_init_banksize,
 	show_dram_config,
+	setup_bdinfo,
 #if defined(CONFIG_M68K) || defined(CONFIG_MIPS) || defined(CONFIG_PPC) || \
 	defined(CONFIG_SH)
 	setup_board_part1,
include/init.h +10 -0
index e727031514..2a8c910677 100644
@@ -141,6 +141,16 @@ int arch_reserve_stacks(void);
  */
 int arch_reserve_mmu(void);
 
+/**
+ * setup_bdinfo() - Generic boardinfo setup
+ *
+ * Routine for populating various generic boardinfo fields of
+ * gd->bd. It is called during the generic board init sequence.
+ *
+ * Return: 0 if OK
+ */
+int setup_bdinfo(void);
+
 /**
  * init_cache_f_r() - Turn on the cache in preparation for relocation
  *
Signature · 1 line
2.17.1
#8 lore raw

PATCH v3 7/17 board_f: Introduce arch_setup_bdinfo initcall

In reply to Ovidiu Panait

Certain architectures (ppc, mips, sh, m68k) use setup board_part1 and setup_board_part2 calls during pre-relocation init to populate gd->bd boardinfo fields. This makes the generic init sequence cluttered with arch-specific ifdefs.

In order to clean these arch-specific sequences from generic init, introduce arch_setup_bdinfo weak initcall so that everyone can define their own bdinfo setup routines.

---

 common/board_f.c |  7 ++++++-
 include/init.h   | 12 ++++++++++++
 2 files changed, 18 insertions(+), 1 deletion(-)
common/board_f.c +6 -1
index 72446f6da5..4356431488 100644
@@ -598,11 +598,16 @@ static int display_new_sp(void)
 	return 0;
 }
 
-int setup_bdinfo(void)
+__weak int arch_setup_bdinfo(void)
 {
 	return 0;
 }
 
+int setup_bdinfo(void)
+{
+	return arch_setup_bdinfo();
+}
+
 #if defined(CONFIG_M68K) || defined(CONFIG_MIPS) || defined(CONFIG_PPC) || \
 	defined(CONFIG_SH)
 static int setup_board_part1(void)
include/init.h +12 -0
index 2a8c910677..e9354e8fca 100644
@@ -141,6 +141,18 @@ int arch_reserve_stacks(void);
  */
 int arch_reserve_mmu(void);
 
+/**
+ * arch_setup_bdinfo() - Architecture dependent boardinfo setup
+ *
+ * Architecture-specific routine for populating various boardinfo fields of
+ * gd->bd. It is called during the generic board init sequence.
+ *
+ * If an implementation is not provided, it will just be a nop stub.
+ *
+ * Return: 0 if OK
+ */
+int arch_setup_bdinfo(void);
+
 /**
  * setup_bdinfo() - Generic boardinfo setup
  *
Signature · 1 line
2.17.1
#9 lore raw

PATCH v3 8/17 board_f: Introduce board_setup_bdinfo_mem initcall

In reply to Ovidiu Panait

In most cases (arc, ppc, mips, sh, m68k) gd->bd->bi_memsize and gd->bd->bi_memstart are populated in a similar fashion:

    bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;
    bd->bi_memsize = gd->ram_size;

However, there is a special case in board/cadence/xtfpga/xtfpga.c that populates those fields in a board specific manner:

    gd->bd->bi_memstart = PHYSADDR(CONFIG_SYS_SDRAM_BASE);
    gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;

Due to this fact, a weak board-specific routine is introduced to take care of this scenario. Also, move all assignments to bi_mem* fields to setup_bdinfo initcall.

Use gd->ram_base to populate bi_memstart to avoid an ifdef.

---

 arch/arc/lib/cpu.c            |  2 --
 board/cadence/xtfpga/xtfpga.c |  7 ++++++-
 common/board_f.c              | 21 +++++++++++++++------
 include/init.h                | 12 ++++++++++++
 4 files changed, 33 insertions(+), 9 deletions(-)
arch/arc/lib/cpu.c +0 -2
index 27b5832a0c..ccb7e1b265 100644
@@ -27,8 +27,6 @@ int arch_cpu_init(void)
 
 int arch_early_init_r(void)
 {
-	gd->bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;
-	gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
 	return 0;
 }
 
board/cadence/xtfpga/xtfpga.c +6 -1
index 2869e5cf68..6f168f3f9f 100644
@@ -49,7 +49,7 @@ int checkboard(void)
 	return 0;
 }
 
-int dram_init_banksize(void)
+int board_setup_bdinfo_mem(void)
 {
 	gd->bd->bi_memstart = PHYSADDR(CONFIG_SYS_SDRAM_BASE);
 	gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
@@ -57,6 +57,11 @@ int dram_init_banksize(void)
 	return 0;
 }
 
+int dram_init_banksize(void)
+{
+	return 0;
+}
+
 int board_postclk_init(void)
 {
 	/*
common/board_f.c +15 -6
index 4356431488..ac72096e3a 100644
@@ -598,6 +598,19 @@ static int display_new_sp(void)
 	return 0;
 }
 
+__weak int board_setup_bdinfo_mem(void)
+{
+	struct bd_info *bd = gd->bd;
+
+	/*
+	 * Save local variables to board info struct
+	 */
+	bd->bi_memstart = gd->ram_base;  /* start of memory */
+	bd->bi_memsize = gd->ram_size;   /* size in bytes */
+
+	return 0;
+}
+
 __weak int arch_setup_bdinfo(void)
 {
 	return 0;
@@ -605,6 +618,8 @@ __weak int arch_setup_bdinfo(void)
 
 int setup_bdinfo(void)
 {
+	board_setup_bdinfo_mem();
+
 	return arch_setup_bdinfo();
 }
 
@@ -614,12 +629,6 @@ static int setup_board_part1(void)
 {
 	struct bd_info *bd = gd->bd;
 
-	/*
-	 * Save local variables to board info struct
-	 */
-	bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;	/* start of memory */
-	bd->bi_memsize = gd->ram_size;			/* size in bytes */
-
 #ifdef CONFIG_SYS_SRAM_BASE
 	bd->bi_sramstart = CONFIG_SYS_SRAM_BASE;	/* start of SRAM */
 	bd->bi_sramsize = CONFIG_SYS_SRAM_SIZE;		/* size  of SRAM */
include/init.h +12 -0
index e9354e8fca..85c8f49095 100644
@@ -141,6 +141,18 @@ int arch_reserve_stacks(void);
  */
 int arch_reserve_mmu(void);
 
+/**
+ * board_setup_bdinfo_mem() - Populate gd->bd->bi_mem* fields
+ *
+ * Board-specific routine for populating gd->bd->bi_mem* fields.
+ * It is called during the generic board init sequence in setup_bdinfo.
+ *
+ * If an implementation is not provided, the generic one will be used.
+ *
+ * Return: 0 if OK
+ */
+int board_setup_bdinfo_mem(void);
+
 /**
  * arch_setup_bdinfo() - Architecture dependent boardinfo setup
  *
Signature · 1 line
2.17.1
#10 lore raw

PATCH v3 8/17 board_f: Introduce board_setup_bdinfo_mem initcall

Hi Ovidiu,

[snip]

arch/arc/lib/cpu.c int arch_cpu_init(void) · line 30

Quoted 11 lines
arch/arc/lib/cpu.c +0 -2
index 27b5832a0c..ccb7e1b265 100644
@@ -27,8 +27,6 @@ int arch_cpu_init(void)
 
 int arch_early_init_r(void)
 {
-       gd->bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;
-       gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
         return 0;

Do we still need an empty arch_early_init_r()?
I.e. get rid of it and:
--------------------------------->8-------------------------------

arch/Kconfig +0 -1
index 91e049b322..2cc656b641 100644
@@ -10,7 +10,6 @@ choice
 
 config ARC
        bool "ARC architecture"
-       select ARCH_EARLY_INIT_R
        select ARC_TIMER
        select CLK
        select HAVE_PRIVATE_LIBGCC

--------------------------------->8-------------------------------

-Alexey

#11 lore raw

PATCH v3 8/17 board_f: Introduce board_setup_bdinfo_mem initcall

Quoted 23 lines · Alexey Brodkin

Hi Ovidiu,

[snip]

arch/arc/lib/cpu.c int arch_cpu_init(void) · line 30

Quoted 11 lines
arch/arc/lib/cpu.c +0 -2
index 27b5832a0c..ccb7e1b265 100644
@@ -27,8 +27,6 @@ int arch_cpu_init(void)
 
  int arch_early_init_r(void)
  {
-       gd->bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;
-       gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
          return 0;

Do we still need an empty arch_early_init_r()?
I.e. get rid of it and:
--------------------------------->8-------------------------------

arch/Kconfig +0 -0
index 91e049b322..2cc656b641 100644

arch/Kconfig choice

Quoted 8 lines
arch/Kconfig +0 -2
@@ -10,7 +10,6 @@ choice
 
  config ARC
         bool "ARC architecture"
-       select ARCH_EARLY_INIT_R
         select ARC_TIMER
         select CLK
         select HAVE_PRIVATE_LIBGCC
--------------------------------->8-------------------------------

Hi Alexey,

Thanks for your input. I'll include these changes in v4.

Ovidiu

Quoted 1 line

-Alexey

#12 lore raw

PATCH v3 8/17 board_f: Introduce board_setup_bdinfo_mem initcall

In reply to Ovidiu Panait

Hi Ovidiu,

Quoted 19 lines · Ovidiu Panait

In most cases (arc, ppc, mips, sh, m68k) gd->bd->bi_memsize and gd->bd->bi_memstart are populated in a similar fashion:

    bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;
    bd->bi_memsize = gd->ram_size;

However, there is a special case in board/cadence/xtfpga/xtfpga.c that populates those fields in a board specific manner:

    gd->bd->bi_memstart = PHYSADDR(CONFIG_SYS_SDRAM_BASE);
    gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;

Due to this fact, a weak board-specific routine is introduced to take care of this scenario. Also, move all assignments to bi_mem* fields to setup_bdinfo initcall.

Use gd->ram_base to populate bi_memstart to avoid an ifdef.

Quoted 8 lines

---

 arch/arc/lib/cpu.c            |  2 --
 board/cadence/xtfpga/xtfpga.c |  7 ++++++-
 common/board_f.c              | 21 +++++++++++++++------
 include/init.h                | 12 ++++++++++++
 4 files changed, 33 insertions(+), 9 deletions(-)

This is unfortunate and I would much rather that some board-specific code fix it up earlier or later. But I can't see an obvious place to do this.

Regards,
Simon

#13 lore raw

PATCH v3 9/17 board_f: Move sram bdinfo assignments to generic code

In reply to Ovidiu Panait

Move sram related bdinfo from arch-specific setup_board_part1 to generic code in setup_bdinfo. Also use "if (IS_ENABLED(CONFIG_SYS_HAS_SRAM))" instead of "#ifdef CONFIG_SYS_SRAM_BASE".

---

 common/board_f.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)
common/board_f.c +7 -5
index ac72096e3a..1befab5446 100644
@@ -618,8 +618,15 @@ __weak int arch_setup_bdinfo(void)
 
 int setup_bdinfo(void)
 {
+	struct bd_info *bd = gd->bd;
+
 	board_setup_bdinfo_mem();
 
+	if (IS_ENABLED(CONFIG_SYS_HAS_SRAM)) {
+		bd->bi_sramstart = CONFIG_SYS_SRAM_BASE; /* start of SRAM */
+		bd->bi_sramsize = CONFIG_SYS_SRAM_SIZE;  /* size  of SRAM */
+	}
+
 	return arch_setup_bdinfo();
 }
 
@@ -629,11 +636,6 @@ static int setup_board_part1(void)
 {
 	struct bd_info *bd = gd->bd;
 
-#ifdef CONFIG_SYS_SRAM_BASE
-	bd->bi_sramstart = CONFIG_SYS_SRAM_BASE;	/* start of SRAM */
-	bd->bi_sramsize = CONFIG_SYS_SRAM_SIZE;		/* size  of SRAM */
-#endif
-
 #if defined(CONFIG_E500) || defined(CONFIG_MPC86xx)
 	bd->bi_immr_base = CONFIG_SYS_IMMR;	/* base  of IMMR register     */
 #endif
Signature · 1 line
2.17.1
#14 lore raw

PATCH v3 9/17 board_f: Move sram bdinfo assignments to generic code

Quoted 10 lines · Ovidiu Panait

Move sram related bdinfo from arch-specific setup_board_part1 to generic code in setup_bdinfo. Also use "if (IS_ENABLED(CONFIG_SYS_HAS_SRAM))" instead of "#ifdef CONFIG_SYS_SRAM_BASE".

---

 common/board_f.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)
#15 lore raw

PATCH v3 10/17 board_f: m68k: Factor out m68k-specific bdinfo setup

In reply to Ovidiu Panait

Factor out m68k-specific bdinfo setup to arch_setup_bdinfo in arch/m68k/lib/bdinfo.c. Also, use if(IS_ENABLED()) instead of #ifdef where possible.

---

 arch/m68k/lib/bdinfo.c | 21 +++++++++++++++++++++
 common/board_f.c       | 19 ++++---------------
 2 files changed, 25 insertions(+), 15 deletions(-)
arch/m68k/lib/bdinfo.c +21 -0
index b7bc6a3044..404e5f19ed 100644
@@ -11,6 +11,27 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
+int arch_setup_bdinfo(void)
+{
+	struct bd_info *bd = gd->bd;
+
+	bd->bi_mbar_base = CONFIG_SYS_MBAR; /* base of internal registers */
+
+	bd->bi_intfreq = gd->cpu_clk;	/* Internal Freq, in Hz */
+	bd->bi_busfreq = gd->bus_clk;	/* Bus Freq,      in Hz */
+
+	if (IS_ENABLED(CONFIG_PCI))
+		bd->bi_pcifreq = gd->pci_clk;
+
+#if defined(CONFIG_EXTRA_CLOCK)
+	bd->bi_inpfreq = gd->arch.inp_clk;	/* input Freq in Hz */
+	bd->bi_vcofreq = gd->arch.vco_clk;	/* vco Freq in Hz */
+	bd->bi_flbfreq = gd->arch.flb_clk;	/* flexbus Freq in Hz */
+#endif
+
+	return 0;
+}
+
 void arch_print_bdinfo(void)
 {
 	struct bd_info *bd = gd->bd;
common/board_f.c +4 -15
index 1befab5446..8ab76a5c7a 100644
@@ -630,7 +630,7 @@ int setup_bdinfo(void)
 	return arch_setup_bdinfo();
 }
 
-#if defined(CONFIG_M68K) || defined(CONFIG_MIPS) || defined(CONFIG_PPC) || \
+#if defined(CONFIG_MIPS) || defined(CONFIG_PPC) || \
 	defined(CONFIG_SH)
 static int setup_board_part1(void)
 {
@@ -639,9 +639,6 @@ static int setup_board_part1(void)
 #if defined(CONFIG_E500) || defined(CONFIG_MPC86xx)
 	bd->bi_immr_base = CONFIG_SYS_IMMR;	/* base  of IMMR register     */
 #endif
-#if defined(CONFIG_M68K)
-	bd->bi_mbar_base = CONFIG_SYS_MBAR;	/* base of internal registers */
-#endif
 #if defined(CONFIG_MPC83xx)
 	bd->bi_immrbar = CONFIG_SYS_IMMR;
 #endif
@@ -650,7 +647,7 @@ static int setup_board_part1(void)
 }
 #endif
 
-#if defined(CONFIG_PPC) || defined(CONFIG_M68K)
+#if defined(CONFIG_PPC)
 static int setup_board_part2(void)
 {
 	struct bd_info *bd = gd->bd;
@@ -663,14 +660,6 @@ static int setup_board_part2(void)
 	bd->bi_sccfreq = gd->arch.scc_clk;
 	bd->bi_vco = gd->arch.vco_out;
 #endif /* CONFIG_CPM2 */
-#if defined(CONFIG_M68K) && defined(CONFIG_PCI)
-	bd->bi_pcifreq = gd->pci_clk;
-#endif
-#if defined(CONFIG_EXTRA_CLOCK)
-	bd->bi_inpfreq = gd->arch.inp_clk;	/* input Freq in Hz */
-	bd->bi_vcofreq = gd->arch.vco_clk;	/* vco Freq in Hz */
-	bd->bi_flbfreq = gd->arch.flb_clk;	/* flexbus Freq in Hz */
-#endif
 
 	return 0;
 }
@@ -997,11 +986,11 @@ static const init_fnc_t init_sequence_f[] = {
 	dram_init_banksize,
 	show_dram_config,
 	setup_bdinfo,
-#if defined(CONFIG_M68K) || defined(CONFIG_MIPS) || defined(CONFIG_PPC) || \
+#if defined(CONFIG_MIPS) || defined(CONFIG_PPC) || \
 	defined(CONFIG_SH)
 	setup_board_part1,
 #endif
-#if defined(CONFIG_PPC) || defined(CONFIG_M68K)
+#if defined(CONFIG_PPC)
 	INIT_FUNC_WATCHDOG_RESET
 	setup_board_part2,
 #endif
Signature · 1 line
2.17.1
#16 lore raw

PATCH v3 10/17 board_f: m68k: Factor out m68k-specific bdinfo setup

Quoted 11 lines · Ovidiu Panait

Factor out m68k-specific bdinfo setup to arch_setup_bdinfo in arch/m68k/lib/bdinfo.c. Also, use if(IS_ENABLED()) instead of #ifdef where possible.

---

 arch/m68k/lib/bdinfo.c | 21 +++++++++++++++++++++
 common/board_f.c       | 19 ++++---------------
 2 files changed, 25 insertions(+), 15 deletions(-)
#17 lore raw

PATCH v3 11/17 board_f: ppc: Factor out ppc-specific bdinfo setup

In reply to Ovidiu Panait

Factor out ppc-specific bdinfo setup from generic init sequence to arch_setup_bdinfo in arch/powerpc/lib/bdinfo.c.

---

 arch/powerpc/lib/bdinfo.c | 25 +++++++++++++++++++++++++
 common/board_f.c          | 36 ++----------------------------------
 2 files changed, 27 insertions(+), 34 deletions(-)
arch/powerpc/lib/bdinfo.c +25 -0
index 07f823ee7a..36c9c99ee6 100644
@@ -11,6 +11,31 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
+int arch_setup_bdinfo(void)
+{
+	struct bd_info *bd = gd->bd;
+
+#if defined(CONFIG_E500) || defined(CONFIG_MPC86xx)
+	bd->bi_immr_base = CONFIG_SYS_IMMR;	/* base  of IMMR register     */
+#endif
+
+#if defined(CONFIG_MPC83xx)
+	bd->bi_immrbar = CONFIG_SYS_IMMR;
+#endif
+
+	bd->bi_intfreq = gd->cpu_clk;	/* Internal Freq, in Hz */
+	bd->bi_busfreq = gd->bus_clk;	/* Bus Freq,      in Hz */
+
+#if defined(CONFIG_CPM2)
+	bd->bi_cpmfreq = gd->arch.cpm_clk;
+	bd->bi_brgfreq = gd->arch.brg_clk;
+	bd->bi_sccfreq = gd->arch.scc_clk;
+	bd->bi_vco = gd->arch.vco_out;
+#endif /* CONFIG_CPM2 */
+
+	return 0;
+}
+
 void __weak board_detail(void)
 {
 	/* Please define board_detail() for your PPC platform */
common/board_f.c +2 -34
index 8ab76a5c7a..7eb65fc224 100644
@@ -630,37 +630,9 @@ int setup_bdinfo(void)
 	return arch_setup_bdinfo();
 }
 
-#if defined(CONFIG_MIPS) || defined(CONFIG_PPC) || \
-	defined(CONFIG_SH)
+#if defined(CONFIG_MIPS) || defined(CONFIG_SH)
 static int setup_board_part1(void)
 {
-	struct bd_info *bd = gd->bd;
-
-#if defined(CONFIG_E500) || defined(CONFIG_MPC86xx)
-	bd->bi_immr_base = CONFIG_SYS_IMMR;	/* base  of IMMR register     */
-#endif
-#if defined(CONFIG_MPC83xx)
-	bd->bi_immrbar = CONFIG_SYS_IMMR;
-#endif
-
-	return 0;
-}
-#endif
-
-#if defined(CONFIG_PPC)
-static int setup_board_part2(void)
-{
-	struct bd_info *bd = gd->bd;
-
-	bd->bi_intfreq = gd->cpu_clk;	/* Internal Freq, in Hz */
-	bd->bi_busfreq = gd->bus_clk;	/* Bus Freq,      in Hz */
-#if defined(CONFIG_CPM2)
-	bd->bi_cpmfreq = gd->arch.cpm_clk;
-	bd->bi_brgfreq = gd->arch.brg_clk;
-	bd->bi_sccfreq = gd->arch.scc_clk;
-	bd->bi_vco = gd->arch.vco_out;
-#endif /* CONFIG_CPM2 */
-
 	return 0;
 }
 #endif
@@ -986,14 +958,10 @@ static const init_fnc_t init_sequence_f[] = {
 	dram_init_banksize,
 	show_dram_config,
 	setup_bdinfo,
-#if defined(CONFIG_MIPS) || defined(CONFIG_PPC) || \
-	defined(CONFIG_SH)
+#if defined(CONFIG_MIPS) || defined(CONFIG_SH)
 	setup_board_part1,
 #endif
-#if defined(CONFIG_PPC)
 	INIT_FUNC_WATCHDOG_RESET
-	setup_board_part2,
-#endif
 	display_new_sp,
 #ifdef CONFIG_OF_BOARD_FIXUP
 	fix_fdt,
Signature · 1 line
2.17.1
#18 lore raw

PATCH v3 11/17 board_f: ppc: Factor out ppc-specific bdinfo setup

Quoted 10 lines · Ovidiu Panait

Factor out ppc-specific bdinfo setup from generic init sequence to arch_setup_bdinfo in arch/powerpc/lib/bdinfo.c.

---

 arch/powerpc/lib/bdinfo.c | 25 +++++++++++++++++++++++++
 common/board_f.c          | 36 ++----------------------------------
 2 files changed, 27 insertions(+), 34 deletions(-)

Could this be a way to remove the weak SDRAM function?

#19 lore raw

PATCH v3 11/17 board_f: ppc: Factor out ppc-specific bdinfo setup

Hi Simon,

Quoted 7 lines · Simon Glass
Quoted 6 lines · Ovidiu Panait

Factor out ppc-specific bdinfo setup from generic init sequence to arch_setup_bdinfo in arch/powerpc/lib/bdinfo.c.

---

Quoted 6 lines
Quoted 3 lines
  arch/powerpc/lib/bdinfo.c | 25 +++++++++++++++++++++++++
  common/board_f.c          | 36 ++----------------------------------
  2 files changed, 27 insertions(+), 34 deletions(-)

Could this be a way to remove the weak SDRAM function?

I think the SDRAM weak function can be eliminated by overwriting the values set in common/board_f.c using the xtensa-specific arch_setup_bdinfo (arch/xtensa/lib/bdinfo.c), as you suggested.

I plan to replace the weak SDRAM function patch with this one:

iff --git a/arch/Kconfig b/arch/Kconfig
index 9be02d1319..4d9557959c 100644

arch/Kconfig +0 -1
@@ -10,7 +10,6 @@ choice
 
 ?config ARC
 ???? bool "ARC architecture"
-??? select ARCH_EARLY_INIT_R
 ???? select ARC_TIMER
 ???? select CLK
 ???? select HAVE_PRIVATE_LIBGCC
arch/arc/lib/cpu.c +0 -7
index 27b5832a0c..d66a8c867a 100644
@@ -25,13 +25,6 @@ int arch_cpu_init(void)
 ???? return 0;
 ?}
 
-int arch_early_init_r(void)
-{
-??? gd->bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;
-??? gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
-??? return 0;
-}
-
 ?/* This is a dummy function on arc */
 ?int dram_init(void)
 ?{
arch/xtensa/lib/bdinfo.c new file +20 -0
new file mode 100644
index 0000000000..b3ab7227aa
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * XTENSA-specific information for the 'bd' command
+ *
+ * (C) Copyright 2003
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ */
+
+#include <common.h>
+#include <init.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int arch_setup_bdinfo(void)
+{
+??? struct bd_info *bd = gd->bd;
+
+??? gd->bd->bi_memstart = PHYSADDR(CONFIG_SYS_SDRAM_BASE);
+??? gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
+}
board/cadence/xtfpga/xtfpga.c +0 -3
index 2869e5cf68..4b49b6e5c8 100644
@@ -51,9 +51,6 @@ int checkboard(void)
 
 ?int dram_init_banksize(void)
 ?{
-??? gd->bd->bi_memstart = PHYSADDR(CONFIG_SYS_SDRAM_BASE);
-??? gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
-
 ???? return 0;
 ?}
 
common/board_f.c +5 -6
index 4356431488..3b11f08725 100644
@@ -605,6 +605,11 @@ __weak int arch_setup_bdinfo(void)
 
 ?int setup_bdinfo(void)
 ?{
+??? struct bd_info *bd = gd->bd;
+
+??? bd->bi_memstart = gd->ram_base;? /* start of memory */
+??? bd->bi_memsize = gd->ram_size;?? /* size in bytes */
+
 ???? return arch_setup_bdinfo();
 ?}
 
@@ -614,12 +619,6 @@ static int setup_board_part1(void)
 ?{
 ???? struct bd_info *bd = gd->bd;
 
-??? /*
-??? ?* Save local variables to board info struct
-??? ?*/
-??? bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;??? /* start of memory */
-??? bd->bi_memsize = gd->ram_size;??? ??? ??? /* size in bytes */
-
 ?#ifdef CONFIG_SYS_SRAM_BASE
 ???? bd->bi_sramstart = CONFIG_SYS_SRAM_BASE;??? /* start of SRAM */
 ???? bd->bi_sramsize = CONFIG_SYS_SRAM_SIZE;??? ??? /* size? of SRAM */

Do you think this is a better approach?

Ovidiu

#20 lore raw

PATCH v3 11/17 board_f: ppc: Factor out ppc-specific bdinfo setup

Hi Ovidiu,

Quoted 125 lines · Ovidiu Panait

Hi Simon,

Quoted 7 lines · Simon Glass
Quoted 6 lines · Ovidiu Panait

Factor out ppc-specific bdinfo setup from generic init sequence to arch_setup_bdinfo in arch/powerpc/lib/bdinfo.c.

---

Quoted 6 lines
Quoted 3 lines
  arch/powerpc/lib/bdinfo.c | 25 +++++++++++++++++++++++++
  common/board_f.c          | 36 ++----------------------------------
  2 files changed, 27 insertions(+), 34 deletions(-)

Could this be a way to remove the weak SDRAM function?

I think the SDRAM weak function can be eliminated by overwriting the values set in common/board_f.c using the xtensa-specific arch_setup_bdinfo (arch/xtensa/lib/bdinfo.c), as you suggested.

I plan to replace the weak SDRAM function patch with this one:

iff --git a/arch/Kconfig b/arch/Kconfig
index 9be02d1319..4d9557959c 100644

arch/Kconfig +0 -1
@@ -10,7 +10,6 @@ choice
 
  config ARC
      bool "ARC architecture"
-    select ARCH_EARLY_INIT_R
      select ARC_TIMER
      select CLK
      select HAVE_PRIVATE_LIBGCC
arch/arc/lib/cpu.c +0 -7
index 27b5832a0c..d66a8c867a 100644
@@ -25,13 +25,6 @@ int arch_cpu_init(void)
      return 0;
  }
 
-int arch_early_init_r(void)
-{
-    gd->bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;
-    gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
-    return 0;
-}
-
  /* This is a dummy function on arc */
  int dram_init(void)
  {
arch/xtensa/lib/bdinfo.c new file +20 -0
new file mode 100644
index 0000000000..b3ab7227aa
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * XTENSA-specific information for the 'bd' command
+ *
+ * (C) Copyright 2003
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ */
+
+#include <common.h>
+#include <init.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int arch_setup_bdinfo(void)
+{
+    struct bd_info *bd = gd->bd;
+
+    gd->bd->bi_memstart = PHYSADDR(CONFIG_SYS_SDRAM_BASE);
+    gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
+}
board/cadence/xtfpga/xtfpga.c +0 -3
index 2869e5cf68..4b49b6e5c8 100644
@@ -51,9 +51,6 @@ int checkboard(void)
 
  int dram_init_banksize(void)
  {
-    gd->bd->bi_memstart = PHYSADDR(CONFIG_SYS_SDRAM_BASE);
-    gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
-
      return 0;
  }
 
common/board_f.c +5 -6
index 4356431488..3b11f08725 100644
@@ -605,6 +605,11 @@ __weak int arch_setup_bdinfo(void)
 
  int setup_bdinfo(void)
  {
+    struct bd_info *bd = gd->bd;
+
+    bd->bi_memstart = gd->ram_base;  /* start of memory */
+    bd->bi_memsize = gd->ram_size;   /* size in bytes */
+
      return arch_setup_bdinfo();
  }
 
@@ -614,12 +619,6 @@ static int setup_board_part1(void)
  {
      struct bd_info *bd = gd->bd;
 
-    /*
-     * Save local variables to board info struct
-     */
-    bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;    /* start of memory */
-    bd->bi_memsize = gd->ram_size;            /* size in bytes */
-
  #ifdef CONFIG_SYS_SRAM_BASE
      bd->bi_sramstart = CONFIG_SYS_SRAM_BASE;    /* start of SRAM */
      bd->bi_sramsize = CONFIG_SYS_SRAM_SIZE;        /* size  of SRAM */
Quoted 1 line

Do you think this is a better approach?

Yes it looks better to me.

Regards,
Simon

#21 lore raw

PATCH v3 11/17 board_f: ppc: Factor out ppc-specific bdinfo setup

Hi Simon,

Quoted 126 lines · Simon Glass

Hi Ovidiu,

Quoted 123 lines · Ovidiu Panait

Hi Simon,

Quoted 7 lines · Simon Glass
Quoted 6 lines · Ovidiu Panait

Factor out ppc-specific bdinfo setup from generic init sequence to arch_setup_bdinfo in arch/powerpc/lib/bdinfo.c.

---

Quoted 6 lines
Quoted 3 lines
   arch/powerpc/lib/bdinfo.c | 25 +++++++++++++++++++++++++
   common/board_f.c          | 36 ++----------------------------------
   2 files changed, 27 insertions(+), 34 deletions(-)

Could this be a way to remove the weak SDRAM function?

I think the SDRAM weak function can be eliminated by overwriting the values set in common/board_f.c using the xtensa-specific arch_setup_bdinfo (arch/xtensa/lib/bdinfo.c), as you suggested.

I plan to replace the weak SDRAM function patch with this one:

iff --git a/arch/Kconfig b/arch/Kconfig
index 9be02d1319..4d9557959c 100644

arch/Kconfig +0 -1
@@ -10,7 +10,6 @@ choice
 
   config ARC
       bool "ARC architecture"
-    select ARCH_EARLY_INIT_R
       select ARC_TIMER
       select CLK
       select HAVE_PRIVATE_LIBGCC
arch/arc/lib/cpu.c +0 -7
index 27b5832a0c..d66a8c867a 100644
@@ -25,13 +25,6 @@ int arch_cpu_init(void)
       return 0;
   }
 
-int arch_early_init_r(void)
-{
-    gd->bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;
-    gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
-    return 0;
-}
-
   /* This is a dummy function on arc */
   int dram_init(void)
   {
arch/xtensa/lib/bdinfo.c new file +20 -0
new file mode 100644
index 0000000000..b3ab7227aa
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * XTENSA-specific information for the 'bd' command
+ *
+ * (C) Copyright 2003
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ */
+
+#include <common.h>
+#include <init.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int arch_setup_bdinfo(void)
+{
+    struct bd_info *bd = gd->bd;
+
+    gd->bd->bi_memstart = PHYSADDR(CONFIG_SYS_SDRAM_BASE);
+    gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
+}
board/cadence/xtfpga/xtfpga.c +0 -3
index 2869e5cf68..4b49b6e5c8 100644
@@ -51,9 +51,6 @@ int checkboard(void)
 
   int dram_init_banksize(void)
   {
-    gd->bd->bi_memstart = PHYSADDR(CONFIG_SYS_SDRAM_BASE);
-    gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
-
       return 0;
   }
 
common/board_f.c +5 -6
index 4356431488..3b11f08725 100644
@@ -605,6 +605,11 @@ __weak int arch_setup_bdinfo(void)
 
   int setup_bdinfo(void)
   {
+    struct bd_info *bd = gd->bd;
+
+    bd->bi_memstart = gd->ram_base;  /* start of memory */
+    bd->bi_memsize = gd->ram_size;   /* size in bytes */
+
       return arch_setup_bdinfo();
   }
 
@@ -614,12 +619,6 @@ static int setup_board_part1(void)
   {
       struct bd_info *bd = gd->bd;
 
-    /*
-     * Save local variables to board info struct
-     */
-    bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;    /* start of memory */
-    bd->bi_memsize = gd->ram_size;            /* size in bytes */
-
   #ifdef CONFIG_SYS_SRAM_BASE
       bd->bi_sramstart = CONFIG_SYS_SRAM_BASE;    /* start of SRAM */
       bd->bi_sramsize = CONFIG_SYS_SRAM_SIZE;        /* size  of SRAM */
Quoted 2 lines
Quoted 1 line

Do you think this is a better approach?

Yes it looks better to me.

In the meantime, I have sent the v4 for this series, containing the above mentioned changes:

https://lists.denx.de/pipermail/u-boot/2020-July/421283.html

Thanks,

Ovidiu

Quoted 2 lines

Regards,
Simon

#22 lore raw

PATCH v3 12/17 board_f: Remove setup_board_part1

In reply to Ovidiu Panait

Now that all arch specific code was converted to setup_bdinfo, we can remove setup_board_part1.

---

 common/board_f.c | 12 +-----------
 1 file changed, 1 insertion(+), 11 deletions(-)
common/board_f.c +1 -11
index 7eb65fc224..25e805faa1 100644
@@ -630,13 +630,6 @@ int setup_bdinfo(void)
 	return arch_setup_bdinfo();
 }
 
-#if defined(CONFIG_MIPS) || defined(CONFIG_SH)
-static int setup_board_part1(void)
-{
-	return 0;
-}
-#endif
-
 #ifdef CONFIG_POST
 static int init_post(void)
 {
@@ -957,11 +950,8 @@ static const init_fnc_t init_sequence_f[] = {
 	reserve_stacks,
 	dram_init_banksize,
 	show_dram_config,
-	setup_bdinfo,
-#if defined(CONFIG_MIPS) || defined(CONFIG_SH)
-	setup_board_part1,
-#endif
 	INIT_FUNC_WATCHDOG_RESET
+	setup_bdinfo,
 	display_new_sp,
 #ifdef CONFIG_OF_BOARD_FIXUP
 	fix_fdt,
Signature · 1 line
2.17.1
#24 lore raw

PATCH v3 13/17 dm: blk: Use IS_ENABLED() instead of #ifdefs in blk_post_probe

In reply to Ovidiu Panait

Use IS_ENABLED() instead of #ifdef in blk_post_probe function.

No functional change intended.

---

 drivers/block/blk-uclass.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)
drivers/block/blk-uclass.c +5 -4
index b19375cbc8..b2738f5717 100644
@@ -644,11 +644,12 @@ int blk_unbind_all(int if_type)
 
 static int blk_post_probe(struct udevice *dev)
 {
-#if defined(CONFIG_PARTITIONS) && defined(CONFIG_HAVE_BLOCK_DEVICE)
-	struct blk_desc *desc = dev_get_uclass_platdata(dev);
+	if (IS_ENABLED(CONFIG_PARTITIONS) &&
+	    IS_ENABLED(CONFIG_HAVE_BLOCK_DEV)) {
+		struct blk_desc *desc = dev_get_uclass_platdata(dev);
 
-	part_init(desc);
-#endif
+		part_init(desc);
+	}
 
 	return 0;
 }
Signature · 1 line
2.17.1
#25 lore raw

PATCH v3 14/17 drivers: serial: Make serial_initialize return int

In reply to Ovidiu Panait

serial_initialize is called only during the common init sequence, after relocation (in common/board_r.c). Because it has a void return value, it has to wrapped in initr_serial. In order to be able to get rid of this indirection, make serial_initialize return int.

Remove extern from prototype in order to silence the following checkpatch warning:
check: extern prototypes should be avoided in .h files

---

 drivers/serial/serial-uclass.c | 4 ++--
 drivers/serial/serial.c        | 4 +++-
 include/serial.h               | 2 +-
 3 files changed, 6 insertions(+), 4 deletions(-)
drivers/serial/serial-uclass.c +2 -2
index a0af0e6bfd..0027625ebf 100644
@@ -170,9 +170,9 @@ int serial_init(void)
 }
 
 /* Called after relocation */
-void serial_initialize(void)
+int serial_initialize(void)
 {
-	serial_init();
+	return serial_init();
 }
 
 static void _serial_putc(struct udevice *dev, char ch)
drivers/serial/serial.c +3 -1
index da017dc5b3..53358acb81 100644
@@ -170,7 +170,7 @@ void serial_register(struct serial_device *dev)
  * serial port to the serial core. That serial port is then used as a
  * default output.
  */
-void serial_initialize(void)
+int serial_initialize(void)
 {
 	atmel_serial_initialize();
 	mcf_serial_initialize();
@@ -183,6 +183,8 @@ void serial_initialize(void)
 	mtk_serial_initialize();
 
 	serial_assign(default_serial_console()->name);
+
+	return 0;
 }
 
 static int serial_stub_start(struct stdio_dev *sdev)
include/serial.h +1 -1
index c590637b1f..6d1e62c677 100644
@@ -42,10 +42,10 @@ extern struct serial_device eserial5_device;
 extern struct serial_device eserial6_device;
 
 extern void serial_register(struct serial_device *);
-extern void serial_initialize(void);
 extern void serial_stdio_init(void);
 extern int serial_assign(const char *name);
 extern void serial_reinit_all(void);
+int serial_initialize(void);
 
 /* For usbtty */
 #ifdef CONFIG_USB_TTY
Signature · 1 line
2.17.1
#26 lore raw

PATCH v3 15/17 common/board_r: Remove initr_serial wrapper

In reply to Ovidiu Panait

Remove the initr_serial->serial_initialize indirection and call serial_initialize directly.

---

 common/board_r.c | 8 +-------
 1 file changed, 1 insertion(+), 7 deletions(-)
common/board_r.c +1 -7
index 67dc25c7d2..79772135a4 100644
@@ -187,12 +187,6 @@ static int initr_reloc_global_data(void)
 	return 0;
 }
 
-static int initr_serial(void)
-{
-	serial_initialize();
-	return 0;
-}
-
 #if defined(CONFIG_PPC) || defined(CONFIG_M68K) || defined(CONFIG_MIPS)
 static int initr_trap(void)
 {
@@ -705,7 +699,7 @@ static init_fnc_t init_sequence_r[] = {
 #endif
 	initr_dm_devices,
 	stdio_init_tables,
-	initr_serial,
+	serial_initialize,
 	initr_announce,
 #if CONFIG_IS_ENABLED(WDT)
 	initr_watchdog,
Signature · 1 line
2.17.1
#27 lore raw

PATCH v3 16/17 blkcache: Extend blkcache_init to cover CONFIG_NEEDS_MANUAL_RELOC

In reply to Ovidiu Panait

Extend manual relocation of block_cache list pointers to all platforms that enable CONFIG_NEEDS_MANUAL_RELOC. Remove m68k-specific checks and provide a single implementation that adds gd->reloc_off to the pre-relocation pointers.

---

 common/board_r.c         |  2 +-
 drivers/block/blkcache.c | 13 +++++++------
 2 files changed, 8 insertions(+), 7 deletions(-)
common/board_r.c +1 -1
index 79772135a4..63c53b7b96 100644
@@ -836,7 +836,7 @@ static init_fnc_t init_sequence_r[] = {
 #if defined(CONFIG_PRAM)
 	initr_mem,
 #endif
-#if defined(CONFIG_M68K) && defined(CONFIG_BLOCK_CACHE)
+#if defined(CONFIG_NEEDS_MANUAL_RELOC) && defined(CONFIG_BLOCK_CACHE)
 	blkcache_init,
 #endif
 	run_main_loop,
drivers/block/blkcache.c +7 -6
index b6fc72fe98..d97ee99cf4 100644
@@ -12,6 +12,8 @@
 #include <linux/ctype.h>
 #include <linux/list.h>
 
+DECLARE_GLOBAL_DATA_PTR;
+
 struct block_cache_node {
 	struct list_head lh;
 	int iftype;
@@ -22,21 +24,20 @@ struct block_cache_node {
 	char *cache;
 };
 
-#ifndef CONFIG_M68K
 static LIST_HEAD(block_cache);
-#else
-static struct list_head block_cache;
-#endif
 
 static struct block_cache_stats _stats = {
 	.max_blocks_per_entry = 8,
 	.max_entries = 32
 };
 
-#ifdef CONFIG_M68K
+#ifdef CONFIG_NEEDS_MANUAL_RELOC
 int blkcache_init(void)
 {
-	INIT_LIST_HEAD(&block_cache);
+	struct list_head *head = &block_cache;
+
+	head->next = (uintptr_t)head->next + gd->reloc_off;
+	head->prev = (uintptr_t)head->prev + gd->reloc_off;
 
 	return 0;
 }
Signature · 1 line
2.17.1
#28 lore raw

PATCH v3 17/17 common/board_r: Move blkcache_init call earlier in the boot sequence

In reply to Ovidiu Panait

blkcache_init manually relocates blkcache list pointers when CONFIG_NEEDS_MANUAL_RELOC is enabled. However, it is called very late in the boot sequence, which could be a problem if previous boot calls execute blkcache operations with the non-relocated pointers. For example, mmc is initialized earlier and might call blkcache_invalidate (in mmc_select_hwpart()) when trying to load the environment from mmc via env_load().

To fix this issue, move blkcache_init boot call earlier, before mmc gets initialized.

---

 common/board_r.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
common/board_r.c +3 -3
index 63c53b7b96..1c307383d5 100644
@@ -705,6 +705,9 @@ static init_fnc_t init_sequence_r[] = {
 	initr_watchdog,
 #endif
 	INIT_FUNC_WATCHDOG_RESET
+#if defined(CONFIG_NEEDS_MANUAL_RELOC) && defined(CONFIG_BLOCK_CACHE)
+	blkcache_init,
+#endif
 #ifdef CONFIG_NEEDS_MANUAL_RELOC
 	initr_manual_reloc_cmdtable,
 #endif
@@ -835,9 +838,6 @@ static init_fnc_t init_sequence_r[] = {
 #endif
 #if defined(CONFIG_PRAM)
 	initr_mem,
-#endif
-#if defined(CONFIG_NEEDS_MANUAL_RELOC) && defined(CONFIG_BLOCK_CACHE)
-	blkcache_init,
 #endif
 	run_main_loop,
 };
Signature · 1 line
2.17.1