Skip to contentSkip to conversation

kernel-fitimage: build configuration for image tree when dtb is not present

PATCH New Usama Arif 1 participant 1 message Jul 20, 2020

lore
Share & tools
lore

Usama Arif

author
#0 lore raw

PATCH v2 1/1 kernel-fitimage: build configuration for image tree when dtb is not present

This patch adds support for adding configuration node even when dtb is not part of the FIT image. The conf and default node number are therefore changed to point to kernel ID rather than dtb ID when dtb does not exist.

---
 meta/classes/kernel-fitimage.bbclass | 29 ++++++++++++++++++++++++++--
 1 file changed, 27 insertions(+), 2 deletions(-)
meta/classes/kernel-fitimage.bbclass +27 -2
index 72b05ff8d1..fa4ea6feef 100644
@@ -257,12 +257,21 @@ fitimage_emit_section_config() {
 	# Test if we have any DTBs at all
 	sep=""
 	conf_desc=""
+	conf_node="conf@"
 	kernel_line=""
 	fdt_line=""
 	ramdisk_line=""
 	setup_line=""
 	default_line=""
 
+	# conf node name is selected based on dtb ID if it is present,
+	# otherwise its selected based on kernel ID
+	if [ -n "${3}" ]; then
+		conf_node=$conf_node${3}
+	else
+		conf_node=$conf_node${2}
+	fi
+
 	if [ -n "${2}" ]; then
 		conf_desc="Linux kernel"
 		sep=", "
@@ -287,12 +296,18 @@ fitimage_emit_section_config() {
 	fi
 
 	if [ "${6}" = "1" ]; then
-		default_line="default = \"conf@${3}\";"
+		# default node is selected based on dtb ID if it is present,
+		# otherwise its selected based on kernel ID
+		if [ -n "${3}" ]; then
+			default_line="default = \"conf@${3}\";"
+		else
+			default_line="default = \"conf@${2}\";"
+		fi
 	fi
 
 	cat << EOF >> ${1}
                 ${default_line}
-                conf@${3} {
+                $conf_node {
 			description = "${6} ${conf_desc}";
 			${kernel_line}
 			${fdt_line}
@@ -434,6 +449,13 @@ fitimage_assemble() {
 	#
 	fitimage_emit_section_maint ${1} confstart
 
+	# kernel-fitimage.bbclass currently only supports a single kernel (no less or
+	# more) to be added to the FIT image along with 0 or more device trees and
+	# 0 or 1 ramdisk.
+	# If a device tree is to be part of the FIT image, then select
+	# the default configuration to be used is based on the dtbcount. If there is
+	# no dtb present than select the default configuation to be based on
+	# the kernelcount.
 	if [ -n "${DTBS}" ]; then
 		i=1
 		for DTB in ${DTBS}; do
@@ -445,6 +467,9 @@ fitimage_assemble() {
 			fi
 			i=`expr ${i} + 1`
 		done
+	else
+		defaultconfigcount=1
+		fitimage_emit_section_config ${1} "${kernelcount}" "" "${ramdiskcount}" "${setupcount}" "${defaultconfigcount}"
 	fi
 
 	fitimage_emit_section_maint ${1} sectend
Signature · 1 line
2.17.1