Skip to contentSkip to conversation

firmware: qcom_scm: disable SDI at boot

RFC PATCH New Brian Norris 1 participant 1 message Jul 21, 2020 Arm Qualcomm mailing list

lore
Share & tools
lore
#0 lore raw

RFC PATCH 1/1 firmware: qcom_scm: disable SDI at boot

*** Disclaimer: I know extremely little about Qualcomm's undocumented SMC API. ***

I'm trying to get upstream support for an IPQ4019 device I have, and by default, warm boot does not work properly -- it appears to trap into TrustZone. I find that the downstream/vendor kernel makes this call at boot, with notes about the watchdog and SDI configuration. It appears some of this is leftover from when they had download-mode enabled, as well as some other debug features, and they didn't get completely turned off in the production bootloader. But I reall can't tell that well; I'm just going off the minimal source code and git logs.

Because this is so undocumented, I can't tell what the right thing to do is -- should this go behind a DT property? Should I apply it only for ipq4019? Is there a better way to describe and document the bits used in this command?

If it helps, I can try to shop around for some testing on other systems.

---
 drivers/firmware/qcom_scm.c | 20 ++++++++++++++++++++
 drivers/firmware/qcom_scm.h |  1 +
 2 files changed, 21 insertions(+)
drivers/firmware/qcom_scm.c +20 -0
index 0e7233a20f34..70c46f1668d1 100644
@@ -394,6 +394,20 @@ static int __qcom_scm_set_dload_mode(struct device *dev, bool enable)
 	return qcom_scm_call(__scm->dev, &desc, NULL);
 }
 
+static int __qcom_scm_disable_sdi(struct device *dev)
+{
+	struct qcom_scm_desc desc = {
+		.svc = QCOM_SCM_SVC_BOOT,
+		.cmd = QCOM_SCM_BOOT_CONFIG_SDI,
+		.arginfo = QCOM_SCM_ARGS(2),
+		.args[0] = 1  /* 1: disable watchdog debug */,
+		.args[1] = 0  /* 0: disable SDI */,
+		.owner = ARM_SMCCC_OWNER_SIP,
+	};
+
+	return qcom_scm_call(__scm->dev, &desc, NULL);
+}
+
 static void qcom_scm_set_download_mode(bool enable)
 {
 	bool avail;
@@ -1122,6 +1136,12 @@ static int qcom_scm_probe(struct platform_device *pdev)
 	if (download_mode)
 		qcom_scm_set_download_mode(true);
 
+	/*
+	 * Some bootloaders leave this enabled by default, which prevents
+	 * normal warm reboot.
+	 */
+	__qcom_scm_disable_sdi(__scm->dev);
+
 	return 0;
 }
 
drivers/firmware/qcom_scm.h +1 -0
index d9ed670da222..39c3dc0dfc50 100644
@@ -74,6 +74,7 @@ extern int scm_legacy_call(struct device *dev, const struct qcom_scm_desc *desc,
 #define QCOM_SCM_SVC_BOOT		0x01
 #define QCOM_SCM_BOOT_SET_ADDR		0x01
 #define QCOM_SCM_BOOT_TERMINATE_PC	0x02
+#define QCOM_SCM_BOOT_CONFIG_SDI	0x09
 #define QCOM_SCM_BOOT_SET_DLOAD_MODE	0x10
 #define QCOM_SCM_BOOT_SET_REMOTE_STATE	0x0a
 #define QCOM_SCM_FLUSH_FLAG_MASK	0x3
Signature · 1 line
2.27.0