Skip to contentSkip to conversation

pinctrl: amd: fix npins for uart0 in kerncz_groups

PATCH In review Sasha Levin 2 participants 11 messages Jul 14, 2020 – Jul 22, 2020

Subsystems (5)
lore
Share & tools
lore

Sasha Levin

author maintainer
#0 lore raw

PATCH 1/9 pinctrl: amd: fix npins for uart0 in kerncz_groups

From: Jacky Hu <[email protected]>

[ Upstream commit 69339d083dfb7786b0e0b3fc19eaddcf11fabdfb ]

uart0_pins is defined as:
static const unsigned uart0_pins[] = {135, 136, 137, 138, 139};

which npins is wronly specified as 9 later

	{
		.name = "uart0",
		.pins = uart0_pins,
		.npins = 9,
	},

npins should be 5 instead of 9 according to the definition.

---
 drivers/pinctrl/pinctrl-amd.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/pinctrl/pinctrl-amd.h +1 -1
index 7bfea47dbb472..f63417197a62f 100644
@@ -249,7 +249,7 @@ static const struct amd_pingroup kerncz_groups[] = {
 	{
 		.name = "uart0",
 		.pins = uart0_pins,
-		.npins = 9,
+		.npins = 5,
 	},
 	{
 		.name = "uart1",
Signature · 1 line
2.25.1
author maintainer
#1 lore raw

PATCH 2/9 mac80211: allow rx of mesh eapol frames with default rx key

From: Markus Theil <[email protected]>

[ Upstream commit 0b467b63870d9c05c81456aa9bfee894ab2db3b6 ]

Without this patch, eapol frames cannot be received in mesh mode, when 802.1X should be used. Initially only a MGTK is defined, which is found and set as rx->key, when there are no other keys set. ieee80211_drop_unencrypted would then drop these eapol frames, as they are data frames without encryption and there exists some rx->key.

Fix this by differentiating between mesh eapol frames and other data frames with existing rx->key. Allow mesh mesh eapol frames only if they are for our vif address.

With this patch in-place, ieee80211_rx_h_mesh_fwding continues after the ieee80211_drop_unencrypted check and notices, that these eapol frames have to be delivered locally, as they should.

---
 net/mac80211/rx.c | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)
net/mac80211/rx.c +26 -0
index a74a6ff18f919..886dce84e70c0 100644
@@ -1963,6 +1963,7 @@ static int ieee80211_802_1x_port_control(struct ieee80211_rx_data *rx)
 
 static int ieee80211_drop_unencrypted(struct ieee80211_rx_data *rx, __le16 fc)
 {
+	struct ieee80211_hdr *hdr = (void *)rx->skb->data;
 	struct sk_buff *skb = rx->skb;
 	struct ieee80211_rx_status *status = IEEE80211_SKB_RXCB(skb);
 
@@ -1973,6 +1974,31 @@ static int ieee80211_drop_unencrypted(struct ieee80211_rx_data *rx, __le16 fc)
 	if (status->flag & RX_FLAG_DECRYPTED)
 		return 0;
 
+	/* check mesh EAPOL frames first */
+	if (unlikely(rx->sta && ieee80211_vif_is_mesh(&rx->sdata->vif) &&
+		     ieee80211_is_data(fc))) {
+		struct ieee80211s_hdr *mesh_hdr;
+		u16 hdr_len = ieee80211_hdrlen(fc);
+		u16 ethertype_offset;
+		__be16 ethertype;
+
+		if (!ether_addr_equal(hdr->addr1, rx->sdata->vif.addr))
+			goto drop_check;
+
+		/* make sure fixed part of mesh header is there, also checks skb len */
+		if (!pskb_may_pull(rx->skb, hdr_len + 6))
+			goto drop_check;
+
+		mesh_hdr = (struct ieee80211s_hdr *)(skb->data + hdr_len);
+		ethertype_offset = hdr_len + ieee80211_get_mesh_hdrlen(mesh_hdr) +
+				   sizeof(rfc1042_header);
+
+		if (skb_copy_bits(rx->skb, ethertype_offset, &ethertype, 2) == 0 &&
+		    ethertype == rx->sdata->control_port_protocol)
+			return 0;
+	}
+
+drop_check:
 	/* Drop unencrypted frames if key is set. */
 	if (unlikely(!ieee80211_has_protected(fc) &&
 		     !ieee80211_is_any_nullfunc(fc) &&
Signature · 1 line
2.25.1
author maintainer
#2 lore raw

PATCH 3/9 scsi: scsi_transport_spi: Fix function pointer check

In reply to Sasha Levin

From: Tom Rix <[email protected]>

[ Upstream commit 5aee52c44d9170591df65fafa1cd408acc1225ce ]

clang static analysis flags several null function pointer problems.

drivers/scsi/scsi_transport_spi.c:374:1: warning: Called function pointer is null (null dereference) [core.CallAndMessage] spi_transport_max_attr(offset, "%d\n");
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Reviewing the store_spi_store_max macro

	if (i->f->set_##field)
		return -EINVAL;

should be

	if (!i->f->set_##field)
		return -EINVAL;
---
 drivers/scsi/scsi_transport_spi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/scsi/scsi_transport_spi.c +1 -1
index 319868f3f6743..083cd11ce7d7d 100644
@@ -353,7 +353,7 @@ store_spi_transport_##field(struct device *dev, 			\
 	struct spi_transport_attrs *tp					\
 		= (struct spi_transport_attrs *)&starget->starget_data;	\
 									\
-	if (i->f->set_##field)						\
+	if (!i->f->set_##field)						\
 		return -EINVAL;						\
 	val = simple_strtoul(buf, NULL, 0);				\
 	if (val > tp->max_##field)					\
Signature · 1 line
2.25.1
author maintainer
#3 lore raw

PATCH 4/9 xtensa: fix __sync_fetch_and_{and,or}_4 declarations

In reply to Sasha Levin

From: Max Filippov <[email protected]>

[ Upstream commit 73f9941306d5ce030f3ffc7db425c7b2a798cf8e ]

Building xtensa kernel with gcc-10 produces the following warnings:
arch/xtensa/kernel/xtensa_ksyms.c:90:15: warning: conflicting types
for built-in function ‘__sync_fetch_and_and_4’; expected ‘unsigned int(volatile void *, unsigned int)’ [-Wbuiltin-declaration-mismatch]
arch/xtensa/kernel/xtensa_ksyms.c:96:15: warning: conflicting types
for built-in function ‘__sync_fetch_and_or_4’; expected ‘unsigned int(volatile void *, unsigned int)’ [-Wbuiltin-declaration-mismatch]

Fix declarations of these functions to avoid the warning.

---
 arch/xtensa/kernel/xtensa_ksyms.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/xtensa/kernel/xtensa_ksyms.c +2 -2
index e2dd9109df633..00f17b5ec9c92 100644
@@ -82,13 +82,13 @@ void __xtensa_libgcc_window_spill(void)
 }
 EXPORT_SYMBOL(__xtensa_libgcc_window_spill);
 
-unsigned long __sync_fetch_and_and_4(unsigned long *p, unsigned long v)
+unsigned int __sync_fetch_and_and_4(volatile void *p, unsigned int v)
 {
 	BUG();
 }
 EXPORT_SYMBOL(__sync_fetch_and_and_4);
 
-unsigned long __sync_fetch_and_or_4(unsigned long *p, unsigned long v)
+unsigned int __sync_fetch_and_or_4(volatile void *p, unsigned int v)
 {
 	BUG();
 }
Signature · 1 line
2.25.1
author maintainer
#4 lore raw

PATCH 5/9 xtensa: update *pos in cpuinfo_op.next

In reply to Sasha Levin

From: Max Filippov <[email protected]>

[ Upstream commit 0d5ab144429e8bd80889b856a44d56ab4a5cd59b ]

Increment *pos in the cpuinfo_op.next to fix the following warning triggered by cat /proc/cpuinfo:

seq_file: buggy .next function c_next did not update position index

---
 arch/xtensa/kernel/setup.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
arch/xtensa/kernel/setup.c +2 -1
index 49ccbd9022f61..92f5a259e2517 100644
@@ -716,7 +716,8 @@ c_start(struct seq_file *f, loff_t *pos)
 static void *
 c_next(struct seq_file *f, void *v, loff_t *pos)
 {
-	return NULL;
+	++*pos;
+	return c_start(f, pos);
 }
 
 static void
Signature · 1 line
2.25.1
author maintainer
#5 lore raw

PATCH 6/9 drivers/net/wan/lapbether: Fixed the value of hard_header_len

In reply to Sasha Levin

From: Xie He <[email protected]>

[ Upstream commit 9dc829a135fb5927f1519de11286e2bbb79f5b66 ]

When this driver transmits data,
first this driver will remove a pseudo header of 1 byte, then the lapb module will prepend the LAPB header of 2 or 3 bytes, then this driver will prepend a length field of 2 bytes, then the underlying Ethernet device will prepend its own header.

So, the header length required should be:
-1 + 3 + 2 + "the header length needed by the underlying device".

This patch fixes kernel panic when this driver is used with AF_PACKET SOCK_DGRAM sockets.

---
 drivers/net/wan/lapbether.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)
drivers/net/wan/lapbether.c +8 -1
index 6676607164d65..f5657783fad4e 100644
@@ -308,7 +308,6 @@ static void lapbeth_setup(struct net_device *dev)
 	dev->netdev_ops	     = &lapbeth_netdev_ops;
 	dev->destructor	     = free_netdev;
 	dev->type            = ARPHRD_X25;
-	dev->hard_header_len = 3;
 	dev->mtu             = 1000;
 	dev->addr_len        = 0;
 }
@@ -329,6 +328,14 @@ static int lapbeth_new_device(struct net_device *dev)
 	if (!ndev)
 		goto out;
 
+	/* When transmitting data:
+	 * first this driver removes a pseudo header of 1 byte,
+	 * then the lapb module prepends an LAPB header of at most 3 bytes,
+	 * then this driver prepends a length field of 2 bytes,
+	 * then the underlying Ethernet device prepends its own header.
+	 */
+	ndev->hard_header_len = -1 + 3 + 2 + dev->hard_header_len;
+
 	lapbeth = netdev_priv(ndev);
 	lapbeth->axdev = ndev;
 
Signature · 1 line
2.25.1
author maintainer
#6 lore raw

PATCH 7/9 ALSA: hda/hdmi: fix failures at PCM open on Intel ICL and later

In reply to Sasha Levin

From: Kai Vehmanen <[email protected]>

[ Upstream commit 56275036d8185f92eceac7479d48b858ee3dab84 ]

When HDMI PCM devices are opened in a specific order, with at least one HDMI/DP receiver connected, ALSA PCM open fails to -EBUSY on the connected monitor, on recent Intel platforms (ICL/JSL and newer). While this is not a typical sequence, at least Pulseaudio does this every time when it is started, to discover the available PCMs.

The rootcause is an invalid assumption in hdmi_add_pin(), where the total number of converters is assumed to be known at the time the function is called. On older Intel platforms this held true, but after ICL/JSL, the order how pins and converters are in the subnode list as returned by snd_hda_get_sub_nodes(), was changed. As a result, information for some converters was not stored to per_pin->mux_nids. And this means some pins cannot be connected to all converters, and application instead gets -EBUSY instead at open.

The assumption that converters are always before pins in the subnode list, is not really a valid one. Fix the problem in hdmi_parse_codec() by introducing separate loops for discovering converters and pins.

---
 sound/pci/hda/patch_hdmi.c | 36 +++++++++++++++++++++++-------------
 1 file changed, 23 insertions(+), 13 deletions(-)
sound/pci/hda/patch_hdmi.c +23 -13
index b249b1b857464..6aa7403ad80ac 100644
@@ -1735,33 +1735,43 @@ static int hdmi_add_cvt(struct hda_codec *codec, hda_nid_t cvt_nid)
 
 static int hdmi_parse_codec(struct hda_codec *codec)
 {
-	hda_nid_t nid;
+	hda_nid_t start_nid;
+	unsigned int caps;
 	int i, nodes;
 
-	nodes = snd_hda_get_sub_nodes(codec, codec->core.afg, &nid);
-	if (!nid || nodes < 0) {
+	nodes = snd_hda_get_sub_nodes(codec, codec->core.afg, &start_nid);
+	if (!start_nid || nodes < 0) {
 		codec_warn(codec, "HDMI: failed to get afg sub nodes\n");
 		return -EINVAL;
 	}
 
-	for (i = 0; i < nodes; i++, nid++) {
-		unsigned int caps;
-		unsigned int type;
+	/*
+	 * hdmi_add_pin() assumes total amount of converters to
+	 * be known, so first discover all converters
+	 */
+	for (i = 0; i < nodes; i++) {
+		hda_nid_t nid = start_nid + i;
 
 		caps = get_wcaps(codec, nid);
-		type = get_wcaps_type(caps);
 
 		if (!(caps & AC_WCAP_DIGITAL))
 			continue;
 
-		switch (type) {
-		case AC_WID_AUD_OUT:
+		if (get_wcaps_type(caps) == AC_WID_AUD_OUT)
 			hdmi_add_cvt(codec, nid);
-			break;
-		case AC_WID_PIN:
+	}
+
+	/* discover audio pins */
+	for (i = 0; i < nodes; i++) {
+		hda_nid_t nid = start_nid + i;
+
+		caps = get_wcaps(codec, nid);
+
+		if (!(caps & AC_WCAP_DIGITAL))
+			continue;
+
+		if (get_wcaps_type(caps) == AC_WID_PIN)
 			hdmi_add_pin(codec, nid);
-			break;
-		}
 	}
 
 	return 0;
Signature · 1 line
2.25.1
#7 lore raw

Re: [PATCH AUTOSEL 4.4 7/9] ALSA: hda/hdmi: fix failures at PCM open on Intel ICL and later

Hi Sasha,

Quoted 7 lines · Sasha Levin

From: Kai Vehmanen <[email protected]>

[ Upstream commit 56275036d8185f92eceac7479d48b858ee3dab84 ]

When HDMI PCM devices are opened in a specific order, with at least one HDMI/DP receiver connected, ALSA PCM open fails to -EBUSY on the connected monitor, on recent Intel platforms (ICL/JSL and newer). While

we don't have Ice Lake hardware support in the HDA HDMI codec driver in any 4.x stable trees (only in 5.1+), so this patch will not help on those and can be dropped.

Br, Kai

author maintainer
#8 lore raw

Re: [PATCH AUTOSEL 4.4 7/9] ALSA: hda/hdmi: fix failures at PCM open on Intel ICL and later

Quoted 8 lines · Kai Vehmanen

Hi Sasha,

Quoted 4 lines · Sasha Levin

From: Kai Vehmanen <[email protected]>

[ Upstream commit 56275036d8185f92eceac7479d48b858ee3dab84 ]

Quoted 7 lines
Quoted 3 lines

When HDMI PCM devices are opened in a specific order, with at least one HDMI/DP receiver connected, ALSA PCM open fails to -EBUSY on the connected monitor, on recent Intel platforms (ICL/JSL and newer). While

we don't have Ice Lake hardware support in the HDA HDMI codec driver in any 4.x stable trees (only in 5.1+), so this patch will not help on those and can be dropped.

Will do, thank you.

Signature · 2 lines
Thanks,
Sasha
author maintainer
#9 lore raw

PATCH 8/9 net: sky2: initialize return of gm_phy_read

In reply to Sasha Levin

From: Tom Rix <[email protected]>

[ Upstream commit 28b18e4eb515af7c6661c3995c6e3c34412c2874 ]

clang static analysis flags this garbage return

drivers/net/ethernet/marvell/sky2.c:208:2: warning: Undefined or garbage value returned to caller [core.uninitialized.UndefReturn]

        return v;
        ^~~~~~~~

static inline u16 gm_phy_read( ...

{
	u16 v;
	__gm_phy_read(hw, port, reg, &v);
	return v;
}

__gm_phy_read can return without setting v.

So handle similar to skge.c's gm_phy_read, initialize v.

---
 drivers/net/ethernet/marvell/sky2.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/marvell/sky2.c +1 -1
index 8ba9eadc20791..3fb9cbdac3bf0 100644
@@ -215,7 +215,7 @@ static int __gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg, u16 *val)
 
 static inline u16 gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg)
 {
-	u16 v;
+	u16 v = 0;
 	__gm_phy_read(hw, port, reg, &v);
 	return v;
 }
Signature · 1 line
2.25.1
author maintainer
#10 lore raw

PATCH 9/9 drm/nouveau/i2c/g94-: increase NV_PMGR_DP_AUXCTL_TRANSACTREQ timeout

In reply to Sasha Levin

From: Ben Skeggs <[email protected]>

[ Upstream commit 0156e76d388310a490aeb0f2fbb5b284ded3aecc ]

Tegra TRM says worst-case reply time is 1216us, and this should fix some spurious timeouts that have been popping up.

---
 drivers/gpu/drm/nouveau/nvkm/subdev/i2c/auxg94.c   | 4 ++--
 drivers/gpu/drm/nouveau/nvkm/subdev/i2c/auxgm204.c | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)
drivers/gpu/drm/nouveau/nvkm/subdev/i2c/auxg94.c +2 -2
index 954f5b76bfcf7..d44965f805fe9 100644
@@ -118,10 +118,10 @@ g94_i2c_aux_xfer(struct nvkm_i2c_aux *obj, bool retry,
 		if (retries)
 			udelay(400);
 
-		/* transaction request, wait up to 1ms for it to complete */
+		/* transaction request, wait up to 2ms for it to complete */
 		nvkm_wr32(device, 0x00e4e4 + base, 0x00010000 | ctrl);
 
-		timeout = 1000;
+		timeout = 2000;
 		do {
 			ctrl = nvkm_rd32(device, 0x00e4e4 + base);
 			udelay(1);
drivers/gpu/drm/nouveau/nvkm/subdev/i2c/auxgm204.c +2 -2
index bed231b56dbd2..7cac8fe372b6b 100644
@@ -118,10 +118,10 @@ gm204_i2c_aux_xfer(struct nvkm_i2c_aux *obj, bool retry,
 		if (retries)
 			udelay(400);
 
-		/* transaction request, wait up to 1ms for it to complete */
+		/* transaction request, wait up to 2ms for it to complete */
 		nvkm_wr32(device, 0x00d954 + base, 0x00010000 | ctrl);
 
-		timeout = 1000;
+		timeout = 2000;
 		do {
 			ctrl = nvkm_rd32(device, 0x00d954 + base);
 			udelay(1);
Signature · 1 line
2.25.1