Skip to contentSkip to conversation

ARM: dts: stm32: Move ethernet PHY into SoM DT

PATCH New Marek Vasut 1 participant 2 messages Jul 24, 2020

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 ARM: dts: stm32: Move ethernet PHY into SoM DT

The PHY and the VIO regulator is populated on the SoM, move it into the SoM DT.

Cc Alexandre Torgue <[email protected]>
Cc Maxime Coquelin <[email protected]>
Cc Patrice Chotard <[email protected]>
Cc Patrick Delaunay <[email protected]>

To: [email protected]

---
 arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi | 33 -----------------
 arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi  | 36 +++++++++++++++++++
 2 files changed, 36 insertions(+), 33 deletions(-)
arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi +0 -33
index 7c4bd615b311..9cf6d90fbf69 100644
@@ -11,7 +11,6 @@ aliases {
 		serial0 = &uart4;
 		serial1 = &usart3;
 		serial2 = &uart8;
-		ethernet0 = &ethernet0;
 	};
 
 	chosen {
@@ -33,16 +32,6 @@ display_bl: display-bl {
 		status = "okay";
 	};
 
-	ethernet_vio: vioregulator {
-		compatible = "regulator-fixed";
-		regulator-name = "vio";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
-		regulator-always-on;
-		regulator-boot-on;
-	};
-
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
 		#size-cells = <0>;
@@ -141,28 +130,6 @@ &cec {
 	status = "okay";
 };
 
-&ethernet0 {
-	status = "okay";
-	pinctrl-0 = <&ethernet0_rmii_pins_a>;
-	pinctrl-1 = <&ethernet0_rmii_sleep_pins_a>;
-	pinctrl-names = "default", "sleep";
-	phy-mode = "rmii";
-	max-speed = <100>;
-	phy-handle = <&phy0>;
-	st,eth-ref-clk-sel;
-	phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
-
-	mdio0 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "snps,dwmac-mdio";
-
-		phy0: ethernet-phy@1 {
-			reg = <1>;
-		};
-	};
-};
-
 &i2c2 {	/* Header X22 */
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c2_pins_a>;
arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi +36 -0
index ba905196fb54..d30a3c60da9b 100644
@@ -9,6 +9,10 @@
 #include <dt-bindings/mfd/st,stpmic1.h>
 
 / {
+	aliases {
+		ethernet0 = &ethernet0;
+	};
+
 	memory@c0000000 {
 		device_type = "memory";
 		reg = <0xC0000000 0x40000000>;
@@ -55,6 +59,16 @@ retram: retram@38000000 {
 			no-map;
 		};
 	};
+
+	ethernet_vio: vioregulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
 };
 
 &adc {
@@ -94,6 +108,28 @@ &dts {
 	status = "okay";
 };
 
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	max-speed = <100>;
+	phy-handle = <&phy0>;
+	st,eth-ref-clk-sel;
+	phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy@1 {
+			reg = <1>;
+		};
+	};
+};
+
 &i2c4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c4_pins_a>;
Signature · 7 lines
2.27.0


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#1 lore raw

PATCH 2/2 ARM: dts: stm32: Add DHSOM based DRC02 board

Add DT for DH DRC02 unit, which is a universal controller device. The system has two ethernet ports, two CANs, RS485 and RS232, USB, capacitive buttons and an OLED display.

Cc Alexandre Torgue <[email protected]>
Cc Maxime Coquelin <[email protected]>
Cc Patrice Chotard <[email protected]>
Cc Patrick Delaunay <[email protected]>

To: [email protected]

---
 arch/arm/boot/dts/Makefile                    |   1 +
 arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dts |  35 ++++
 arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts  |   2 +-
 .../arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi | 157 ++++++++++++++++++
 4 files changed, 194 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dts
 create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi
arch/arm/boot/dts/Makefile +1 -0
index e71ff271fa63..2b19246f6f06 100644
@@ -1047,6 +1047,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
 	stm32746g-eval.dtb \
 	stm32h743i-eval.dtb \
 	stm32h743i-disco.dtb \
+	stm32mp153c-dhcom-drc02.dtb \
 	stm32mp157a-avenger96.dtb \
 	stm32mp157a-dhcor-avenger96.dtb \
 	stm32mp157a-dk1.dtb \
arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dts new file +35 -0
new file mode 100644
index 000000000000..7dd99ad5ad9a
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
+ *
+ * DHCOM STM32MP1 variant:
+ * DHCM-STM32MP153C-C065-R102-F0819-SPI-E2-CAN2-RTC-I-01D2
+ * DHCOM PCB number: 587-200 or newer
+ * DRC02 PCB number: 568-100 or newer
+ */
+/dts-v1/;
+
+#include "stm32mp153.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-drc02.dtsi"
+
+/ {
+	model = "DH Electronics STM32MP153C DHCOM DRC02";
+	compatible = "dh,stm32mp153c-dhcom-drc02", "dh,stm32mp153c-dhcom-som",
+		     "st,stm32mp153";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_a>;
+	pinctrl-1 = <&m_can1_sleep_pins_a>;
+	status = "okay";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "okay";
+};
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts +1 -1
index 197aa98d49e2..9f7349eddd57 100644
@@ -4,7 +4,7 @@
  *
  * DHCOM STM32MP1 variant:
  * DHCM-STM32MP157C-C065-R102-F0819-SPI-E2-CAN2-SDR104-RTC-WBT-T-DSI-I-01D2
- * DHCOR PCB number: 587-200 or newer
+ * DHCOM PCB number: 587-200 or newer
  * PDK2 PCB number: 516-400 or newer
  */
 /dts-v1/;
arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi new file +157 -0

157 lines not on this page · raw message

Signature · 7 lines
2.27.0


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel