arm: imx6q: pcm058: Rework SPI NOR configuration
PATCH 1/1 arm: imx6q: pcm058: Rework SPI NOR configuration
Enable CONFIG_SPL_DM_SPI_FLASH to be able to boot from SPI NOR, modify the offset of U-boot proper in the SPI NOR, so the difference in offset matches between SPL and U-boot matches that of the SD Card, allowing u-boot-with-spl.imx to also be copied to SPI NOR at an offset of 0x400. Update the README to reflect this change.
--- board/phytec/pcm058/README | 20 ++++++++++++-------- configs/pcm058_defconfig | 3 ++- 2 files changed, 14 insertions(+), 9 deletions(-)
board/phytec/pcm058/README +12 -8
@@ -61,17 +61,21 @@ Then, clear the SPI flash: => sf probe => sf erase 0x0 0x1000000 -Load the SPL from raw MMC into memory and copy to the SPI. The SPL is maximum -392*512-byte blocks in size therefore 0x188 blocks, totaling 0x31000 bytes: +Load the equivalent of u-boot-with-spl.imx from the raw MMC into memory and +copy to the SPI. The SPL is expected at an offset of 0x400, and its size is +maximum 392*512-byte blocks in size, therefore 0x188 blocks, totaling 0x31000 +bytes. Assume U-boot should fit into 640KiB, therefore 0x500 512-byte blocks, +totalling 0xA0000 bytes. Adding these together: -=> mmc read ${loadaddr} 0x2 0x188 -=> sf write ${loadaddr} 0x400 0x31000 +=> mmc read ${loadaddr} 0x2 0x688 +=> sf write ${loadaddr} 0x400 0xD1000 -Load the U-boot binary into memory and copy to the SPI. U-boot should fit into -640KiB, so 0x500 512-byte blocks, totalling 0xA0000 bytes: +The SPL is located at offset 0x400, and U-boot at 0x31400 in SPI flash, as to +match the SD Card layout. This would allow, instead of reading from the SD Card +above, with networking and TFTP correctly configured, the equivalent of: -=> mmc read ${loadaddr} 0x18a 0x500 -=> sf write ${loadaddr} 0x40000 0xA0000 +=> tftp u-boot-with-spl.imx +=> sf write ${fileaddr} 0x400 ${filesize} The default NAND bootscripts expect a single MTD partition named "rootfs", which in turn contains the UBI volumes "fit" (which contains the kernel fit-
configs/pcm058_defconfig +2 -1
@@ -7,7 +7,7 @@ CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_ENV_SIZE=0x4000 CONFIG_ENV_OFFSET=0x100000 CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_SYS_SPI_U_BOOT_OFFS=0x40000 +CONFIG_SYS_SPI_U_BOOT_OFFS=0x31400 CONFIG_MX6_OCRAM_256KB=y CONFIG_TARGET_PCM058=y CONFIG_SPL_TEXT_BASE=0x00908000
@@ -34,6 +34,7 @@ CONFIG_SPL_SEPARATE_BSS=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x18a CONFIG_SPL_DMA=y CONFIG_SPL_FS_EXT4=y +CONFIG_SPL_DM_SPI_FLASH=y CONFIG_SPL_SPI_LOAD=y CONFIG_SPL_WATCHDOG_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y
Signature · 1 line
2.26.2
PATCH 1/1 arm: imx6q: pcm058: Rework SPI NOR configuration
Quoted 8 lines
Enable
CONFIG_SPL_DM_SPI_FLASHto be able to boot from SPI NOR, modify the offset of U-boot proper in the SPI NOR, so the difference in offset matches between SPL and U-boot matches that of the SD Card, allowing u-boot-with-spl.imx to also be copied to SPI NOR at an offset of0x400. Update the README to reflect this change.Signed-off-by Niel Fourie <[email protected]>Cc Stefano Babic <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================