4.14.190-rc1 review

This is the start of the stable review cycle for the 4.14.190 release. There are 64 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Wed, 29 Jul 2020 13:48:51 +0000. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

	https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.14.190-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.14.y
and the diffstat can be found below.

thanks,

greg k-h

-------------
Pseudo-Shortlog of commits:

Greg Kroah-Hartman <[email protected]>

    Linux 4.14.190-rc1

Mark O'Donovan <[email protected]>
ath9k: Fix regression with Atheros 9271

Qiujun Huang <[email protected]>
ath9k: Fix general protection fault in ath9k_hif_usb_rx_cb

John David Anglin <[email protected]>
parisc: Add atomic64_set_release() define to avoid CPU soft lockups

Michael J. Ruhl <[email protected]>
io-mapping: indicate mapping failure

Hugh Dickins <[email protected]>
mm/memcg: fix refcount error while moving and swapping

Fangrui Song <[email protected]>
Makefile: Fix GCC_TOOLCHAIN_DIR prefix for Clang cross compilation

Tetsuo Handa <[email protected]>
vt: Reject zero-sized screen buffer size.

Tetsuo Handa <[email protected]>

    fbdev: Detect integer underflow at "struct fbcon_ops"->clear_margins.

Serge Semin <[email protected]>
serial: 8250_mtk: Fix high-speed baud rates clamping

Yang Yingliang <[email protected]>

    serial: 8250: fix null-ptr-deref in serial8250_start_tx()

Ian Abbott <[email protected]>
staging: comedi: addi_apci_1564: check INSN_CONFIG_DIGITAL_TRIG shift

Ian Abbott <[email protected]>
staging: comedi: addi_apci_1500: check INSN_CONFIG_DIGITAL_TRIG shift

Ian Abbott <[email protected]>
staging: comedi: ni_6527: fix INSN_CONFIG_DIGITAL_TRIG support

Ian Abbott <[email protected]>
staging: comedi: addi_apci_1032: check INSN_CONFIG_DIGITAL_TRIG shift

Rustam Kovhaev <[email protected]>
staging: wlan-ng: properly check endpoint types

Steve French <[email protected]>
Revert "cifs: Fix the target file was deleted when rename failed."

Forest Crossman <[email protected]>
usb: xhci: Fix ASM2142/ASM3142 DMA addressing

Chunfeng Yun <[email protected]>
usb: xhci-mtk: fix the failure of bandwidth allocation

Tetsuo Handa <[email protected]>
binder: Don't use mmput() from shrinker function.

Arnd Bergmann <[email protected]>
x86: math-emu: Fix up 'cmp' insn for clang ias

Will Deacon <[email protected]>
arm64: Use test_tsk_thread_flag() for checking TIF_SINGLESTEP

Evgeny Novikov <[email protected]>
usb: gadget: udc: gr_udc: fix memleak on error handling path in gr_ep_init()

Ilya Katsnelson <[email protected]>
Input: synaptics - enable InterTouch for ThinkPad X1E 1st gen

Leonid Ravich <[email protected]>
dmaengine: ioat setting ioat timeout as module parameter

Evgeny Novikov <[email protected]>
hwmon: (aspeed-pwm-tacho) Avoid possible buffer overflow

Marc Kleine-Budde <[email protected]>
regmap: dev_get_regmap_match(): fix string comparison

leilk.liu <[email protected]>
spi: mediatek: use correct SPI_CFG2_REG MACRO

Merlijn Wajer <[email protected]>
Input: add SW_MACHINE_COVER

Dinghao Liu <[email protected]>
dmaengine: tegra210-adma: Fix runtime PM imbalance on error

Hans de Goede <[email protected]>
HID: apple: Disable Fn-key key-re-mapping on clone keyboards

Federico Ricchiuto <[email protected]>
HID: i2c-hid: add Mediacom FlexBook edge13 to descriptor override

Pi-Hsun Shih <[email protected]>
scripts/decode_stacktrace: strip basepath from all paths

Matthew Howell <[email protected]>
serial: exar: Fix GPIO configuration for Sealevel cards based on XR17V35X

Cong Wang <[email protected]>
bonding: check return value of register_netdevice() in bond_newlink()

Wolfram Sang <[email protected]>
i2c: rcar: always clear ICSAR to avoid side effects

guodeqing <[email protected]>
ipvs: fix the connection sync failed in some cases

Liu Jian <[email protected]>
mlxsw: destroy workqueue when trap_register in mlxsw_emad_init

Taehee Yoo <[email protected]>
bonding: check error value of register_netdevice() immediately

Wang Hai <[email protected]>
net: smc91x: Fix possible memory leak in smc_drv_probe()

Chen-Yu Tsai <[email protected]>
drm: sun4i: hdmi: Fix inverted HPD result

Sergey Organov <[email protected]>
net: dp83640: fix SIOCSHWTSTAMP to update the struct with actual configuration

George Kennedy <[email protected]>

    ax88172a: fix ax88172a_unbind() failures

Christophe JAILLET <[email protected]>
hippi: Fix a size used in a 'pci_free_consistent()' in an error handling path

Vasundhara Volam <[email protected]>
bnxt_en: Fix race when modifying pause settings.

Robbie Ko <[email protected]>
btrfs: fix page leaks after failure to lock page for delalloc

Boris Burkov <[email protected]>
btrfs: fix mount failure caused by race with umount

Filipe Manana <[email protected]>
btrfs: fix double free on ulist after backref resolution failure

Hans de Goede <[email protected]>

    ASoC: rt5670: Correct RT5670_LDO_SEL_MASK

Takashi Iwai <[email protected]>
ALSA: info: Drop WARN_ON() from buffer NULL sanity check

Oleg Nesterov <[email protected]>
uprobes: Change handle_swbp() to send SIGTRAP with si_code=SI_KERNEL, to fix GDB regression

Yang Yingliang <[email protected]>
IB/umem: fix reference count leak in ib_umem_odp_get()

Vladimir Oltean <[email protected]>
spi: spi-fsl-dspi: Exit the ISR with IRQ_NONE when it's not ours

Olga Kornievskaia <[email protected]>
SUNRPC reverting d03727b248d0 ("NFSv4 fix CLOSE not waiting for direct IO compeletion")

Thomas Gleixner <[email protected]>
irqdomain/treewide: Keep firmware node unconditionally allocated

Ben Skeggs <[email protected]>
drm/nouveau/i2c/g94-: increase NV_PMGR_DP_AUXCTL_TRANSACTREQ timeout

Tom Rix <[email protected]>
net: sky2: initialize return of gm_phy_read

Xie He <[email protected]>
drivers/net/wan/lapbether: Fixed the value of hard_header_len

Max Filippov <[email protected]>
xtensa: update *pos in cpuinfo_op.next

Max Filippov <[email protected]>
xtensa: fix __sync_fetch_and_{and,or}_4 declarations

Tom Rix <[email protected]>
scsi: scsi_transport_spi: Fix function pointer check

Markus Theil <[email protected]>
mac80211: allow rx of mesh eapol frames with default rx key

Jacky Hu <[email protected]>
pinctrl: amd: fix npins for uart0 in kerncz_groups

Navid Emamdoost <[email protected]>
gpio: arizona: put pm_runtime in case of failure

Navid Emamdoost <[email protected]>
gpio: arizona: handle pm_runtime_get_sync failure case

-------------

Diffstat:

 Makefile                                           |  6 +--
 arch/arm64/kernel/debug-monitors.c                 |  4 +-
 arch/parisc/include/asm/atomic.h                   |  2 +
 arch/x86/kernel/apic/io_apic.c                     | 10 ++---
 arch/x86/kernel/apic/msi.c                         | 16 ++++---
 arch/x86/kernel/apic/vector.c                      |  1 -
 arch/x86/math-emu/wm_sqrt.S                        |  2 +-
 arch/x86/platform/uv/uv_irq.c                      |  3 +-
 arch/xtensa/kernel/setup.c                         |  3 +-
 arch/xtensa/kernel/xtensa_ksyms.c                  |  4 +-
 drivers/android/binder_alloc.c                     |  2 +-
 drivers/base/regmap/regmap.c                       |  2 +-
 drivers/dma/ioat/dma.c                             | 12 +++++
 drivers/dma/ioat/dma.h                             |  2 -
 drivers/dma/tegra210-adma.c                        |  5 ++-
 drivers/gpio/gpio-arizona.c                        |  7 ++-
 drivers/gpu/drm/nouveau/nvkm/subdev/i2c/auxg94.c   |  4 +-
 drivers/gpu/drm/nouveau/nvkm/subdev/i2c/auxgm200.c |  4 +-
 drivers/gpu/drm/sun4i/sun4i_hdmi_enc.c             |  2 +-
 drivers/hid/hid-apple.c                            | 18 ++++++++
 drivers/hid/i2c-hid/i2c-hid-dmi-quirks.c           |  8 ++++
 drivers/hwmon/aspeed-pwm-tacho.c                   |  2 +
 drivers/i2c/busses/i2c-rcar.c                      |  3 ++
 drivers/infiniband/core/umem_odp.c                 |  3 +-
 drivers/input/mouse/synaptics.c                    |  1 +
 drivers/iommu/amd_iommu.c                          |  5 ++-
 drivers/iommu/intel_irq_remapping.c                |  2 +-
 drivers/net/bonding/bond_main.c                    | 10 +++--
 drivers/net/bonding/bond_netlink.c                 |  3 +-
 drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c  |  5 ++-
 drivers/net/ethernet/marvell/sky2.c                |  2 +-
 drivers/net/ethernet/mellanox/mlxsw/core.c         |  3 +-
 drivers/net/ethernet/smsc/smc91x.c                 |  4 +-
 drivers/net/hippi/rrunner.c                        |  2 +-
 drivers/net/phy/dp83640.c                          |  4 ++
 drivers/net/usb/ax88172a.c                         |  1 +
 drivers/net/wan/lapbether.c                        |  9 +++-
 drivers/net/wireless/ath/ath9k/hif_usb.c           | 52 +++++++++++++++++-----
 drivers/net/wireless/ath/ath9k/hif_usb.h           |  5 +++
 drivers/pci/host/vmd.c                             |  5 ++-
 drivers/pinctrl/pinctrl-amd.h                      |  2 +-
 drivers/scsi/scsi_transport_spi.c                  |  2 +-
 drivers/spi/spi-fsl-dspi.c                         |  4 +-
 drivers/spi/spi-mt65xx.c                           | 15 ++++---
 drivers/staging/comedi/drivers/addi_apci_1032.c    | 20 ++++++---
 drivers/staging/comedi/drivers/addi_apci_1500.c    | 24 +++++++---
 drivers/staging/comedi/drivers/addi_apci_1564.c    | 20 ++++++---
 drivers/staging/comedi/drivers/ni_6527.c           |  2 +-
 drivers/staging/wlan-ng/prism2usb.c                | 16 ++++++-
 drivers/tty/serial/8250/8250_core.c                |  2 +-
 drivers/tty/serial/8250/8250_exar.c                | 12 ++++-
 drivers/tty/serial/8250/8250_mtk.c                 | 18 ++++++++
 drivers/tty/vt/vt.c                                | 29 +++++++-----
 drivers/usb/gadget/udc/gr_udc.c                    |  7 ++-
 drivers/usb/host/xhci-mtk-sch.c                    |  4 ++
 drivers/usb/host/xhci-pci.c                        |  3 ++
 drivers/video/fbdev/core/bitblit.c                 |  4 +-
 drivers/video/fbdev/core/fbcon_ccw.c               |  4 +-
 drivers/video/fbdev/core/fbcon_cw.c                |  4 +-
 drivers/video/fbdev/core/fbcon_ud.c                |  4 +-
 fs/btrfs/backref.c                                 |  1 +
 fs/btrfs/extent_io.c                               |  3 +-
 fs/btrfs/volumes.c                                 |  8 ++++
 fs/cifs/inode.c                                    | 10 +----
 fs/nfs/direct.c                                    | 13 ++----
 fs/nfs/file.c                                      |  1 -
 include/linux/io-mapping.h                         |  5 ++-
 include/linux/mod_devicetable.h                    |  2 +-
 include/uapi/linux/input-event-codes.h             |  3 +-
 kernel/events/uprobes.c                            |  2 +-
 mm/memcontrol.c                                    |  4 +-
 net/mac80211/rx.c                                  | 26 +++++++++++
 net/netfilter/ipvs/ip_vs_sync.c                    | 12 +++--
 scripts/decode_stacktrace.sh                       |  4 +-
 sound/core/info.c                                  |  4 +-
 sound/soc/codecs/rt5670.h                          |  2 +-
 76 files changed, 387 insertions(+), 147 deletions(-)

From: Navid Emamdoost <[email protected]>

[ Upstream commit e6f390a834b56583e6fc0949822644ce92fbb107 ]

Calling pm_runtime_get_sync increments the counter even in case of failure, causing incorrect ref count. Call pm_runtime_put if pm_runtime_get_sync fails.

---
 drivers/gpio/gpio-arizona.c | 1 +
 1 file changed, 1 insertion(+)

index d4e6ba0301bc3..e09834b91ea52 100644
@@ -111,6 +111,7 @@ static int arizona_gpio_direction_out(struct gpio_chip *chip,
 		ret = pm_runtime_get_sync(chip->parent);
 		if (ret < 0) {
 			dev_err(chip->parent, "Failed to resume: %d\n", ret);
+			pm_runtime_put(chip->parent);
 			return ret;
 		}
 	}

2.25.1

From: Navid Emamdoost <[email protected]>

[ Upstream commit 861254d826499944cb4d9b5a15f5a794a6b99a69 ]

Calling pm_runtime_get_sync increments the counter even in case of failure, causing incorrect ref count if pm_runtime_put is not called in error handling paths. Call pm_runtime_put if pm_runtime_get_sync fails.

---
 drivers/gpio/gpio-arizona.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

index e09834b91ea52..694674dfbf82a 100644
@@ -69,6 +69,7 @@ static int arizona_gpio_get(struct gpio_chip *chip, unsigned offset)
 		ret = pm_runtime_get_sync(chip->parent);
 		if (ret < 0) {
 			dev_err(chip->parent, "Failed to resume: %d\n", ret);
+			pm_runtime_put_autosuspend(chip->parent);
 			return ret;
 		}
 

@@ -77,12 +78,15 @@ static int arizona_gpio_get(struct gpio_chip *chip, unsigned offset)
 		if (ret < 0) {
 			dev_err(chip->parent, "Failed to drop cache: %d\n",
 				ret);
+			pm_runtime_put_autosuspend(chip->parent);
 			return ret;
 		}
 
 		ret = regmap_read(arizona->regmap, reg, &val);
-		if (ret < 0)
+		if (ret < 0) {
+			pm_runtime_put_autosuspend(chip->parent);
 			return ret;
+		}
 
 		pm_runtime_mark_last_busy(chip->parent);
 		pm_runtime_put_autosuspend(chip->parent);

2.25.1

From: Jacky Hu <[email protected]>

[ Upstream commit 69339d083dfb7786b0e0b3fc19eaddcf11fabdfb ]

uart0_pins is defined as:
static const unsigned uart0_pins[] = {135, 136, 137, 138, 139};

which npins is wronly specified as 9 later

	{
		.name = "uart0",
		.pins = uart0_pins,
		.npins = 9,
	},

npins should be 5 instead of 9 according to the definition.

---
 drivers/pinctrl/pinctrl-amd.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

index 8fa453a59da5e..884f48f7a6a36 100644
@@ -252,7 +252,7 @@ static const struct amd_pingroup kerncz_groups[] = {
 	{
 		.name = "uart0",
 		.pins = uart0_pins,
-		.npins = 9,
+		.npins = 5,
 	},
 	{
 		.name = "uart1",

2.25.1

From: Markus Theil <[email protected]>

[ Upstream commit 0b467b63870d9c05c81456aa9bfee894ab2db3b6 ]

Without this patch, eapol frames cannot be received in mesh mode, when 802.1X should be used. Initially only a MGTK is defined, which is found and set as rx->key, when there are no other keys set. ieee80211_drop_unencrypted would then drop these eapol frames, as they are data frames without encryption and there exists some rx->key.

Fix this by differentiating between mesh eapol frames and other data frames with existing rx->key. Allow mesh mesh eapol frames only if they are for our vif address.

With this patch in-place, ieee80211_rx_h_mesh_fwding continues after the ieee80211_drop_unencrypted check and notices, that these eapol frames have to be delivered locally, as they should.

---
 net/mac80211/rx.c | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

index 56d7a3dfa543b..04ae9de55d74b 100644
@@ -2120,6 +2120,7 @@ static int ieee80211_802_1x_port_control(struct ieee80211_rx_data *rx)
 
 static int ieee80211_drop_unencrypted(struct ieee80211_rx_data *rx, __le16 fc)
 {
+	struct ieee80211_hdr *hdr = (void *)rx->skb->data;
 	struct sk_buff *skb = rx->skb;
 	struct ieee80211_rx_status *status = IEEE80211_SKB_RXCB(skb);
 

@@ -2130,6 +2131,31 @@ static int ieee80211_drop_unencrypted(struct ieee80211_rx_data *rx, __le16 fc)
 	if (status->flag & RX_FLAG_DECRYPTED)
 		return 0;
 
+	/* check mesh EAPOL frames first */
+	if (unlikely(rx->sta && ieee80211_vif_is_mesh(&rx->sdata->vif) &&
+		     ieee80211_is_data(fc))) {
+		struct ieee80211s_hdr *mesh_hdr;
+		u16 hdr_len = ieee80211_hdrlen(fc);
+		u16 ethertype_offset;
+		__be16 ethertype;
+
+		if (!ether_addr_equal(hdr->addr1, rx->sdata->vif.addr))
+			goto drop_check;
+
+		/* make sure fixed part of mesh header is there, also checks skb len */
+		if (!pskb_may_pull(rx->skb, hdr_len + 6))
+			goto drop_check;
+
+		mesh_hdr = (struct ieee80211s_hdr *)(skb->data + hdr_len);
+		ethertype_offset = hdr_len + ieee80211_get_mesh_hdrlen(mesh_hdr) +
+				   sizeof(rfc1042_header);
+
+		if (skb_copy_bits(rx->skb, ethertype_offset, &ethertype, 2) == 0 &&
+		    ethertype == rx->sdata->control_port_protocol)
+			return 0;
+	}
+
+drop_check:
 	/* Drop unencrypted frames if key is set. */
 	if (unlikely(!ieee80211_has_protected(fc) &&
 		     !ieee80211_is_any_nullfunc(fc) &&

2.25.1

From: Tom Rix <[email protected]>

[ Upstream commit 5aee52c44d9170591df65fafa1cd408acc1225ce ]

clang static analysis flags several null function pointer problems.

drivers/scsi/scsi_transport_spi.c:374:1: warning: Called function pointer is null (null dereference) [core.CallAndMessage] spi_transport_max_attr(offset, "%d\n");
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Reviewing the store_spi_store_max macro

	if (i->f->set_##field)
		return -EINVAL;

should be

	if (!i->f->set_##field)
		return -EINVAL;

---
 drivers/scsi/scsi_transport_spi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

index d0219e36080c3..e626fc2cc7813 100644
@@ -349,7 +349,7 @@ store_spi_transport_##field(struct device *dev, 			\
 	struct spi_transport_attrs *tp					\
 		= (struct spi_transport_attrs *)&starget->starget_data;	\
 									\
-	if (i->f->set_##field)						\
+	if (!i->f->set_##field)						\
 		return -EINVAL;						\
 	val = simple_strtoul(buf, NULL, 0);				\
 	if (val > tp->max_##field)					\

2.25.1

From: Max Filippov <[email protected]>

[ Upstream commit 73f9941306d5ce030f3ffc7db425c7b2a798cf8e ]

Building xtensa kernel with gcc-10 produces the following warnings:
arch/xtensa/kernel/xtensa_ksyms.c:90:15: warning: conflicting types
for built-in function ‘__sync_fetch_and_and_4’; expected ‘unsigned int(volatile void *, unsigned int)’ [-Wbuiltin-declaration-mismatch]
arch/xtensa/kernel/xtensa_ksyms.c:96:15: warning: conflicting types
for built-in function ‘__sync_fetch_and_or_4’; expected ‘unsigned int(volatile void *, unsigned int)’ [-Wbuiltin-declaration-mismatch]

Fix declarations of these functions to avoid the warning.

---
 arch/xtensa/kernel/xtensa_ksyms.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

index dc7b470a423a6..58b79e2ea569c 100644
@@ -82,13 +82,13 @@ void __xtensa_libgcc_window_spill(void)
 }
 EXPORT_SYMBOL(__xtensa_libgcc_window_spill);
 
-unsigned long __sync_fetch_and_and_4(unsigned long *p, unsigned long v)
+unsigned int __sync_fetch_and_and_4(volatile void *p, unsigned int v)
 {
 	BUG();
 }
 EXPORT_SYMBOL(__sync_fetch_and_and_4);
 
-unsigned long __sync_fetch_and_or_4(unsigned long *p, unsigned long v)
+unsigned int __sync_fetch_and_or_4(volatile void *p, unsigned int v)
 {
 	BUG();
 }

2.25.1

From: Max Filippov <[email protected]>

[ Upstream commit 0d5ab144429e8bd80889b856a44d56ab4a5cd59b ]

Increment *pos in the cpuinfo_op.next to fix the following warning triggered by cat /proc/cpuinfo:

seq_file: buggy .next function c_next did not update position index

---
 arch/xtensa/kernel/setup.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

index 92fb20777bb0e..a19c61b261422 100644
@@ -711,7 +711,8 @@ c_start(struct seq_file *f, loff_t *pos)
 static void *
 c_next(struct seq_file *f, void *v, loff_t *pos)
 {
-	return NULL;
+	++*pos;
+	return c_start(f, pos);
 }
 
 static void

2.25.1

From: Xie He <[email protected]>

[ Upstream commit 9dc829a135fb5927f1519de11286e2bbb79f5b66 ]

When this driver transmits data,
first this driver will remove a pseudo header of 1 byte, then the lapb module will prepend the LAPB header of 2 or 3 bytes, then this driver will prepend a length field of 2 bytes, then the underlying Ethernet device will prepend its own header.

So, the header length required should be:
-1 + 3 + 2 + "the header length needed by the underlying device".

This patch fixes kernel panic when this driver is used with AF_PACKET SOCK_DGRAM sockets.

---
 drivers/net/wan/lapbether.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

index 0e3f8ed84660e..ac34257e9f203 100644
@@ -308,7 +308,6 @@ static void lapbeth_setup(struct net_device *dev)
 	dev->netdev_ops	     = &lapbeth_netdev_ops;
 	dev->needs_free_netdev = true;
 	dev->type            = ARPHRD_X25;
-	dev->hard_header_len = 3;
 	dev->mtu             = 1000;
 	dev->addr_len        = 0;
 }

@@ -329,6 +328,14 @@ static int lapbeth_new_device(struct net_device *dev)
 	if (!ndev)
 		goto out;
 
+	/* When transmitting data:
+	 * first this driver removes a pseudo header of 1 byte,
+	 * then the lapb module prepends an LAPB header of at most 3 bytes,
+	 * then this driver prepends a length field of 2 bytes,
+	 * then the underlying Ethernet device prepends its own header.
+	 */
+	ndev->hard_header_len = -1 + 3 + 2 + dev->hard_header_len;
+
 	lapbeth = netdev_priv(ndev);
 	lapbeth->axdev = ndev;
 

2.25.1

From: Tom Rix <[email protected]>

[ Upstream commit 28b18e4eb515af7c6661c3995c6e3c34412c2874 ]

clang static analysis flags this garbage return

drivers/net/ethernet/marvell/sky2.c:208:2: warning: Undefined or garbage value returned to caller [core.uninitialized.UndefReturn]

        return v;
        ^~~~~~~~

static inline u16 gm_phy_read( ...

{
	u16 v;
	__gm_phy_read(hw, port, reg, &v);
	return v;
}

__gm_phy_read can return without setting v.

So handle similar to skge.c's gm_phy_read, initialize v.

---
 drivers/net/ethernet/marvell/sky2.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

index 5046efdad5390..34ae4bf6e7162 100644
@@ -215,7 +215,7 @@ io_error:
 
 static inline u16 gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg)
 {
-	u16 v;
+	u16 v = 0;
 	__gm_phy_read(hw, port, reg, &v);
 	return v;
 }

2.25.1

From: Ben Skeggs <[email protected]>

[ Upstream commit 0156e76d388310a490aeb0f2fbb5b284ded3aecc ]

Tegra TRM says worst-case reply time is 1216us, and this should fix some spurious timeouts that have been popping up.

---
 drivers/gpu/drm/nouveau/nvkm/subdev/i2c/auxg94.c   | 4 ++--
 drivers/gpu/drm/nouveau/nvkm/subdev/i2c/auxgm200.c | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

index c8ab1b5741a3e..db7769cb33eba 100644
@@ -118,10 +118,10 @@ g94_i2c_aux_xfer(struct nvkm_i2c_aux *obj, bool retry,
 		if (retries)
 			udelay(400);
 
-		/* transaction request, wait up to 1ms for it to complete */
+		/* transaction request, wait up to 2ms for it to complete */
 		nvkm_wr32(device, 0x00e4e4 + base, 0x00010000 | ctrl);
 
-		timeout = 1000;
+		timeout = 2000;
 		do {
 			ctrl = nvkm_rd32(device, 0x00e4e4 + base);
 			udelay(1);

index 7ef60895f43a7..edb6148cbca04 100644
@@ -118,10 +118,10 @@ gm200_i2c_aux_xfer(struct nvkm_i2c_aux *obj, bool retry,
 		if (retries)
 			udelay(400);
 
-		/* transaction request, wait up to 1ms for it to complete */
+		/* transaction request, wait up to 2ms for it to complete */
 		nvkm_wr32(device, 0x00d954 + base, 0x00010000 | ctrl);
 
-		timeout = 1000;
+		timeout = 2000;
 		do {
 			ctrl = nvkm_rd32(device, 0x00d954 + base);
 			udelay(1);

2.25.1

From: Thomas Gleixner <[email protected]>

[ Upstream commit e3beca48a45b5e0e6e6a4e0124276b8248dcc9bb ]

Quite some non OF/ACPI users of irqdomains allocate firmware nodes of type IRQCHIP_FWNODE_NAMED or IRQCHIP_FWNODE_NAMED_ID and free them right after creating the irqdomain. The only purpose of these FW nodes is to convey name information. When this was introduced the core code did not store the pointer to the node in the irqdomain. A recent change stored the firmware node pointer in irqdomain for other reasons and missed to notice that the usage sites which do the alloc_fwnode/create_domain/free_fwnode sequence are broken by this. Storing a dangling pointer is dangerous itself, but in case that the domain is destroyed later on this leads to a double free.

Remove the freeing of the firmware node after creating the irqdomain from all affected call sites to cure this.

---
 arch/x86/kernel/apic/io_apic.c      | 10 +++++-----
 arch/x86/kernel/apic/msi.c          | 16 +++++++++++-----
 arch/x86/kernel/apic/vector.c       |  1 -
 arch/x86/platform/uv/uv_irq.c       |  3 ++-
 drivers/iommu/amd_iommu.c           |  5 +++--
 drivers/iommu/intel_irq_remapping.c |  2 +-
 drivers/pci/host/vmd.c              |  5 +++--
 7 files changed, 25 insertions(+), 17 deletions(-)

index 2271adbc3c42a..b5652233e6745 100644
@@ -2233,12 +2233,12 @@ static int mp_irqdomain_create(int ioapic)
 	ip->irqdomain = irq_domain_create_linear(fn, hwirqs, cfg->ops,
 						 (void *)(long)ioapic);
 
-	/* Release fw handle if it was allocated above */
-	if (!cfg->dev)
-		irq_domain_free_fwnode(fn);
-
-	if (!ip->irqdomain)
+	if (!ip->irqdomain) {
+		/* Release fw handle if it was allocated above */
+		if (!cfg->dev)
+			irq_domain_free_fwnode(fn);
 		return -ENOMEM;
+	}
 
 	ip->irqdomain->parent = parent;
 

index f10e7f93b0e2c..8c102d62b8596 100644
@@ -149,10 +149,11 @@ void __init arch_init_msi_domain(struct irq_domain *parent)
 		msi_default_domain =
 			pci_msi_create_irq_domain(fn, &pci_msi_domain_info,
 						  parent);
-		irq_domain_free_fwnode(fn);
 	}
-	if (!msi_default_domain)
+	if (!msi_default_domain) {
+		irq_domain_free_fwnode(fn);
 		pr_warn("failed to initialize irqdomain for MSI/MSI-x.\n");
+	}
 }
 
 #ifdef CONFIG_IRQ_REMAP

@@ -185,7 +186,8 @@ struct irq_domain *arch_create_remap_msi_irq_domain(struct irq_domain *parent,
 	if (!fn)
 		return NULL;
 	d = pci_msi_create_irq_domain(fn, &pci_msi_ir_domain_info, parent);
-	irq_domain_free_fwnode(fn);
+	if (!d)
+		irq_domain_free_fwnode(fn);
 	return d;
 }
 #endif

@@ -248,7 +250,8 @@ static struct irq_domain *dmar_get_irq_domain(void)
 	if (fn) {
 		dmar_domain = msi_create_irq_domain(fn, &dmar_msi_domain_info,
 						    x86_vector_domain);
-		irq_domain_free_fwnode(fn);
+		if (!dmar_domain)
+			irq_domain_free_fwnode(fn);
 	}
 out:
 	mutex_unlock(&dmar_lock);

@@ -373,7 +376,10 @@ struct irq_domain *hpet_create_irq_domain(int hpet_id)
 	}
 
 	d = msi_create_irq_domain(fn, domain_info, parent);
-	irq_domain_free_fwnode(fn);
+	if (!d) {
+		irq_domain_free_fwnode(fn);
+		kfree(domain_info);
+	}
 	return d;
 }
 

index b958082c74a77..36cd34524ac19 100644
@@ -457,7 +457,6 @@ int __init arch_early_irq_init(void)
 	x86_vector_domain = irq_domain_create_tree(fn, &x86_vector_domain_ops,
 						   NULL);
 	BUG_ON(x86_vector_domain == NULL);
-	irq_domain_free_fwnode(fn);
 	irq_set_default_host(x86_vector_domain);
 
 	arch_init_msi_domain(x86_vector_domain);

index 03fc397335b74..c9fc725a1dcf4 100644
@@ -171,9 +171,10 @@ static struct irq_domain *uv_get_irq_domain(void)
 		goto out;
 
 	uv_domain = irq_domain_create_tree(fn, &uv_domain_ops, NULL);
-	irq_domain_free_fwnode(fn);
 	if (uv_domain)
 		uv_domain->parent = x86_vector_domain;
+	else
+		irq_domain_free_fwnode(fn);
 out:
 	mutex_unlock(&uv_lock);
 

index 778f167be2d35..494caaa265af0 100644
@@ -4394,9 +4394,10 @@ int amd_iommu_create_irq_domain(struct amd_iommu *iommu)
 	if (!fn)
 		return -ENOMEM;
 	iommu->ir_domain = irq_domain_create_tree(fn, &amd_ir_domain_ops, iommu);
-	irq_domain_free_fwnode(fn);
-	if (!iommu->ir_domain)
+	if (!iommu->ir_domain) {
+		irq_domain_free_fwnode(fn);
 		return -ENOMEM;
+	}
 
 	iommu->ir_domain->parent = arch_get_ir_parent_domain();
 	iommu->msi_domain = arch_create_remap_msi_irq_domain(iommu->ir_domain,

index 25842b566c39c..154949a499c21 100644
@@ -536,8 +536,8 @@ static int intel_setup_irq_remapping(struct intel_iommu *iommu)
 					    0, INTR_REMAP_TABLE_ENTRIES,
 					    fn, &intel_ir_domain_ops,
 					    iommu);
-	irq_domain_free_fwnode(fn);
 	if (!iommu->ir_domain) {
+		irq_domain_free_fwnode(fn);
 		pr_err("IR%d: failed to allocate irqdomain\n", iommu->seq_id);
 		goto out_free_bitmap;
 	}

index af6d5da10ea5f..05f191ae0ff1b 100644
@@ -638,9 +638,10 @@ static int vmd_enable_domain(struct vmd_dev *vmd)
 
 	vmd->irq_domain = pci_msi_create_irq_domain(fn, &vmd_msi_domain_info,
 						    x86_vector_domain);
-	irq_domain_free_fwnode(fn);
-	if (!vmd->irq_domain)
+	if (!vmd->irq_domain) {
+		irq_domain_free_fwnode(fn);
 		return -ENODEV;
+	}
 
 	pci_add_resource(&resources, &vmd->resources[0]);
 	pci_add_resource(&resources, &vmd->resources[1]);

2.25.1

From: Olga Kornievskaia <[email protected]>

commit 65caafd0d2145d1dd02072c4ced540624daeab40 upstream.

Reverting commit d03727b248d0 "NFSv4 fix CLOSE not waiting for direct IO compeletion". This patch made it so that fput() by calling inode_dio_done() in nfs_file_release() would wait uninterruptably for any outstanding directIO to the file (but that wait on IO should be killable).

The problem the patch was also trying to address was REMOVE returning ERR_ACCESS because the file is still opened, is supposed to be resolved by server returning ERR_FILE_OPEN and not ERR_ACCESS.

---
 fs/nfs/direct.c |   13 ++++---------
 fs/nfs/file.c   |    1 -
 2 files changed, 4 insertions(+), 10 deletions(-)

@@ -396,6 +396,8 @@ static void nfs_direct_complete(struct n
 {
 	struct inode *inode = dreq->inode;
 
+	inode_dio_end(inode);
+
 	if (dreq->iocb) {
 		long res = (long) dreq->error;
 		if (dreq->count != 0) {

@@ -407,10 +409,7 @@ static void nfs_direct_complete(struct n
 
 	complete(&dreq->completion);
 
-	igrab(inode);
 	nfs_direct_req_release(dreq);
-	inode_dio_end(inode);
-	iput(inode);
 }
 
 static void nfs_direct_read_completion(struct nfs_pgio_header *hdr)

@@ -540,10 +539,8 @@ static ssize_t nfs_direct_read_schedule_
 	 * generic layer handle the completion.
 	 */
 	if (requested_bytes == 0) {
-		igrab(inode);
-		nfs_direct_req_release(dreq);
 		inode_dio_end(inode);
-		iput(inode);
+		nfs_direct_req_release(dreq);
 		return result < 0 ? result : -EIO;
 	}
 

@@ -960,10 +957,8 @@ static ssize_t nfs_direct_write_schedule
 	 * generic layer handle the completion.
 	 */
 	if (requested_bytes == 0) {
-		igrab(inode);
-		nfs_direct_req_release(dreq);
 		inode_dio_end(inode);
-		iput(inode);
+		nfs_direct_req_release(dreq);
 		return result < 0 ? result : -EIO;
 	}
 

@@ -82,7 +82,6 @@ nfs_file_release(struct inode *inode, st
 	dprintk("NFS: release(%pD2)\n", filp);
 
 	nfs_inc_stats(inode, NFSIOS_VFSRELEASE);
-	inode_dio_wait(inode);
 	nfs_file_clear_open_context(filp);
 	return 0;
 }

From: Vladimir Oltean <[email protected]>

commit d41f36a6464a85c06ad920703d878e4491d2c023 upstream.

The DSPI interrupt can be shared between two controllers at least on the LX2160A. In that case, the driver for one controller might misbehave and consume the other's interrupt. Fix this by actually checking if any of the bits in the status register have been asserted.

---
 drivers/spi/spi-fsl-dspi.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

@@ -886,9 +886,11 @@ static irqreturn_t dspi_interrupt(int ir
 					trans_mode);
 			}
 		}
+
+		return IRQ_HANDLED;
 	}
 
-	return IRQ_HANDLED;
+	return IRQ_NONE;
 }
 
 static const struct of_device_id fsl_dspi_dt_ids[] = {

From: Yang Yingliang <[email protected]>

Add missing mmput() on error path to avoid ref-count leak.

This problem is introduced by 79bb5b7ee177 ("RDMA/umem: Fix missing mmap_sem in get umem ODP call") and resolved by f27a0d50a4bc ("RDMA/umem: Use umem->owning_mm inside ODP").
So, it's only needed in stable-4.14 and stable-4.19.

---
 drivers/infiniband/core/umem_odp.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

@@ -306,7 +306,8 @@ int ib_umem_odp_get(struct ib_ucontext *
 		vma = find_vma(mm, ib_umem_start(umem));
 		if (!vma || !is_vm_hugetlb_page(vma)) {
 			up_read(&mm->mmap_sem);
-			return -EINVAL;
+			ret_val = -EINVAL;
+			goto out_mm;
 		}
 		h = hstate_vma(vma);
 		umem->page_shift = huge_page_shift(h);

From: Oleg Nesterov <[email protected]>

commit fe5ed7ab99c656bd2f5b79b49df0e9ebf2cead8a upstream.

If a tracee is uprobed and it hits int3 inserted by debugger, handle_swbp() does send_sig(SIGTRAP, current, 0) which means si_code == SI_USER. This used to work when this code was written, but then GDB started to validate si_code and now it simply can't use breakpoints if the tracee has an active uprobe:

	# cat test.c
	void unused_func(void)
	{
	}
	int main(void)
	{
		return 0;
	}

	# gcc -g test.c -o test
	# perf probe -x ./test -a unused_func
	# perf record -e probe_test:unused_func gdb ./test -ex run
	GNU gdb (GDB) 10.0.50.20200714-git
	...
	Program received signal SIGTRAP, Trace/breakpoint trap.
	0x00007ffff7ddf909 in dl_main () from /lib64/ld-linux-x86-64.so.2
	(gdb)

The tracee hits the internal breakpoint inserted by GDB to monitor shared library events but GDB misinterprets this SIGTRAP and reports a signal.

Change handle_swbp() to use force_sig(SIGTRAP), this matches do_int3_user() and fixes the problem.

This is the minimal fix for -stable, arch/x86/kernel/uprobes.c is equally wrong; it should use send_sigtrap(TRAP_TRACE) instead of send_sig(SIGTRAP), but this doesn't confuse GDB and needs another x86-specific patch.

---
 kernel/events/uprobes.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -1893,7 +1893,7 @@ static void handle_swbp(struct pt_regs *
 	if (!uprobe) {
 		if (is_swbp > 0) {
 			/* No matching uprobe; signal SIGTRAP. */
-			send_sig(SIGTRAP, current, 0);
+			force_sig(SIGTRAP, current);
 		} else {
 			/*
 			 * Either we raced with uprobe_unregister() or we can't

From: Takashi Iwai <[email protected]>

commit 60379ba08532eca861e933b389526a4dc89e0c42 upstream.

snd_info_get_line() has a sanity check of NULL buffer -- both buffer itself being NULL and buffer->buffer being NULL. Basically both checks are valid and necessary, but the problem is that it's with snd_BUG_ON() macro that triggers WARN_ON(). The latter condition (NULL buffer->buffer) can be met arbitrarily by user since the buffer is allocated at the first write, so it means that user can trigger WARN_ON() at will.

This patch addresses it by simply moving buffer->buffer NULL check out of snd_BUG_ON() so that spurious WARNING is no longer triggered.

---
 sound/core/info.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

@@ -634,7 +634,9 @@ int snd_info_get_line(struct snd_info_bu
 {
 	int c = -1;
 
-	if (snd_BUG_ON(!buffer || !buffer->buffer))
+	if (snd_BUG_ON(!buffer))
+		return 1;
+	if (!buffer->buffer)
 		return 1;
 	if (len <= 0 || buffer->stop || buffer->error)
 		return 1;

From: Hans de Goede <[email protected]>

commit 5cacc6f5764e94fa753b2c1f5f7f1f3f74286e82 upstream.

The RT5670_PWR_ANLG1 register has 3 bits to select the LDO voltage, so the correct mask is 0x7 not 0x3.

Because of this wrong mask we were programming the ldo bits to a setting of binary 001 (0x05 & 0x03) instead of binary 101 when moving to SND_SOC_BIAS_PREPARE.

According to the datasheet 001 is a reserved value, so no idea what it did, since the driver was working fine before I guess we got lucky and it does something which is ok.

---
 sound/soc/codecs/rt5670.h |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -760,7 +760,7 @@
 #define RT5670_PWR_VREF2_BIT			4
 #define RT5670_PWR_FV2				(0x1 << 3)
 #define RT5670_PWR_FV2_BIT			3
-#define RT5670_LDO_SEL_MASK			(0x3)
+#define RT5670_LDO_SEL_MASK			(0x7)
 #define RT5670_LDO_SEL_SFT			0
 
 /* Power Management for Analog 2 (0x64) */

From: Filipe Manana <[email protected]>

commit 580c079b5766ac706f56eec5c79aee4bf929fef6 upstream.

At btrfs_find_all_roots_safe() we allocate a ulist and set the **roots argument to point to it. However if later we fail due to an error returned by find_parent_nodes(), we free that ulist but leave a dangling pointer in the **roots argument. Upon receiving the error, a caller of this function can attempt to free the same ulist again, resulting in an invalid memory access.

One such scenario is during qgroup accounting:

btrfs_qgroup_account_extents()

--> calls btrfs_find_all_roots() passes &new_roots (a stack allocated
pointer) to btrfs_find_all_roots()

--> btrfs_find_all_roots() just calls btrfs_find_all_roots_safe()
passing &new_roots to it

--> allocates ulist and assigns its address to **roots (which
points to new_roots from btrfs_qgroup_account_extents())

--> find_parent_nodes() returns an error, so we free the ulist
and leave **roots pointing to it after returning

--> btrfs_qgroup_account_extents() sees btrfs_find_all_roots() returned
an error and jumps to the label 'cleanup', which just tries to free again the same ulist

Stack trace example:

 ------------[ cut here ]------------
 BTRFS: tree first key check failed
 WARNING: CPU: 1 PID: 1763215 at fs/btrfs/disk-io.c:422 btrfs_verify_level_key+0xe0/0x180 [btrfs]
 Modules linked in: dm_snapshot dm_thin_pool (...)
 CPU: 1 PID: 1763215 Comm: fsstress Tainted: G        W         5.8.0-rc3-btrfs-next-64 #1
 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
 RIP: 0010:btrfs_verify_level_key+0xe0/0x180 [btrfs]
 Code: 28 5b 5d (...)
 RSP: 0018:ffffb89b473779a0 EFLAGS: 00010286
 RAX: 0000000000000000 RBX: ffff90397759bf08 RCX: 0000000000000000
 RDX: 0000000000000001 RSI: 0000000000000027 RDI: 00000000ffffffff
 RBP: ffff9039a419c000 R08: 0000000000000000 R09: 0000000000000000
 R10: 0000000000000000 R11: ffffb89b43301000 R12: 000000000000005e
 R13: ffffb89b47377a2e R14: ffffb89b473779af R15: 0000000000000000
 FS:  00007fc47e1e1000(0000) GS:ffff9039ac200000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 00007fc47e1df000 CR3: 00000003d9e4e001 CR4: 00000000003606e0
 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
 Call Trace:
  read_block_for_search+0xf6/0x350 [btrfs]
  btrfs_next_old_leaf+0x242/0x650 [btrfs]
  resolve_indirect_refs+0x7cf/0x9e0 [btrfs]
  find_parent_nodes+0x4ea/0x12c0 [btrfs]
  btrfs_find_all_roots_safe+0xbf/0x130 [btrfs]
  btrfs_qgroup_account_extents+0x9d/0x390 [btrfs]
  btrfs_commit_transaction+0x4f7/0xb20 [btrfs]
  btrfs_sync_file+0x3d4/0x4d0 [btrfs]
  do_fsync+0x38/0x70
  __x64_sys_fdatasync+0x13/0x20
  do_syscall_64+0x5c/0xe0
  entry_SYSCALL_64_after_hwframe+0x44/0xa9
 RIP: 0033:0x7fc47e2d72e3
 Code: Bad RIP value.
 RSP: 002b:00007fffa32098c8 EFLAGS: 00000246 ORIG_RAX: 000000000000004b
 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007fc47e2d72e3
 RDX: 00007fffa3209830 RSI: 00007fffa3209830 RDI: 0000000000000003
 RBP: 000000000000072e R08: 0000000000000001 R09: 0000000000000003
 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000000003e8
 R13: 0000000051eb851f R14: 00007fffa3209970 R15: 00005607c4ac8b50
 irq event stamp: 0
 hardirqs last  enabled at (0): [<0000000000000000>] 0x0
 hardirqs last disabled at (0): [<ffffffffb8eb5e85>] copy_process+0x755/0x1eb0
 softirqs last  enabled at (0): [<ffffffffb8eb5e85>] copy_process+0x755/0x1eb0
 softirqs last disabled at (0): [<0000000000000000>] 0x0
 ---[ end trace 8639237550317b48 ]---
 BTRFS error (device sdc): tree first key mismatch detected, bytenr=62324736 parent_transid=94 key expected=(262,108,1351680) has=(259,108,1921024)
 general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b6b: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC PTI
 CPU: 2 PID: 1763215 Comm: fsstress Tainted: G        W         5.8.0-rc3-btrfs-next-64 #1
 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
 RIP: 0010:ulist_release+0x14/0x60 [btrfs]
 Code: c7 07 00 (...)
 RSP: 0018:ffffb89b47377d60 EFLAGS: 00010282
 RAX: 6b6b6b6b6b6b6b6b RBX: ffff903959b56b90 RCX: 0000000000000000
 RDX: 0000000000000001 RSI: 0000000000270024 RDI: ffff9036e2adc840
 RBP: ffff9036e2adc848 R08: 0000000000000000 R09: 0000000000000000
 R10: 0000000000000000 R11: 0000000000000000 R12: ffff9036e2adc840
 R13: 0000000000000015 R14: ffff9039a419ccf8 R15: ffff90395d605840
 FS:  00007fc47e1e1000(0000) GS:ffff9039ac600000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 00007f8c1c0a51c8 CR3: 00000003d9e4e004 CR4: 00000000003606e0
 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
 Call Trace:
  ulist_free+0x13/0x20 [btrfs]
  btrfs_qgroup_account_extents+0xf3/0x390 [btrfs]
  btrfs_commit_transaction+0x4f7/0xb20 [btrfs]
  btrfs_sync_file+0x3d4/0x4d0 [btrfs]
  do_fsync+0x38/0x70
  __x64_sys_fdatasync+0x13/0x20
  do_syscall_64+0x5c/0xe0
  entry_SYSCALL_64_after_hwframe+0x44/0xa9
 RIP: 0033:0x7fc47e2d72e3
 Code: Bad RIP value.
 RSP: 002b:00007fffa32098c8 EFLAGS: 00000246 ORIG_RAX: 000000000000004b
 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007fc47e2d72e3
 RDX: 00007fffa3209830 RSI: 00007fffa3209830 RDI: 0000000000000003
 RBP: 000000000000072e R08: 0000000000000001 R09: 0000000000000003
 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000000003e8
 R13: 0000000051eb851f R14: 00007fffa3209970 R15: 00005607c4ac8b50
 Modules linked in: dm_snapshot dm_thin_pool (...)
 ---[ end trace 8639237550317b49 ]---
 RIP: 0010:ulist_release+0x14/0x60 [btrfs]
 Code: c7 07 00 (...)
 RSP: 0018:ffffb89b47377d60 EFLAGS: 00010282
 RAX: 6b6b6b6b6b6b6b6b RBX: ffff903959b56b90 RCX: 0000000000000000
 RDX: 0000000000000001 RSI: 0000000000270024 RDI: ffff9036e2adc840
 RBP: ffff9036e2adc848 R08: 0000000000000000 R09: 0000000000000000
 R10: 0000000000000000 R11: 0000000000000000 R12: ffff9036e2adc840
 R13: 0000000000000015 R14: ffff9039a419ccf8 R15: ffff90395d605840
 FS:  00007fc47e1e1000(0000) GS:ffff9039ad200000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 00007f6a776f7d40 CR3: 00000003d9e4e002 CR4: 00000000003606e0
 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400

Fix this by making btrfs_find_all_roots_safe() set *roots to NULL after it frees the ulist.

---
 fs/btrfs/backref.c |    1 +
 1 file changed, 1 insertion(+)

@@ -1420,6 +1420,7 @@ static int btrfs_find_all_roots_safe(str
 		if (ret < 0 && ret != -ENOENT) {
 			ulist_free(tmp);
 			ulist_free(*roots);
+			*roots = NULL;
 			return ret;
 		}
 		node = ulist_next(tmp, &uiter);

From: Boris Burkov <[email protected]>

commit 48cfa61b58a1fee0bc49eef04f8ccf31493b7cdd upstream.

It is possible to cause a btrfs mount to fail by racing it with a slow umount. The crux of the sequence is generic_shutdown_super not yet calling sop->put_super before btrfs_mount_root calls btrfs_open_devices. If that occurs, btrfs_open_devices will decide the opened counter is non-zero, increment it, and skip resetting fs_devices->total_rw_bytes to
0. From here, mount will call sget which will result in grab_super trying to take the super block umount semaphore. That semaphore will be held by the slow umount, so mount will block. Before up-ing the semaphore, umount will delete the super block, resulting in mount's sget reliably allocating a new one, which causes the mount path to dutifully fill it out, and increment total_rw_bytes a second time, which causes the mount to fail, as we see double the expected bytes.

Here is the sequence laid out in greater detail:

CPU0 CPU1
down_write sb->s_umount
btrfs_kill_super
kill_anon_super(sb)

    generic_shutdown_super(sb);
      shrink_dcache_for_umount(sb);
      sync_filesystem(sb);
      evict_inodes(sb); // SLOW

                                              btrfs_mount_root
                                                btrfs_scan_one_device
                                                fs_devices = device->fs_devices
                                                fs_info->fs_devices = fs_devices
                                                // fs_devices-opened makes this a no-op
                                                btrfs_open_devices(fs_devices, mode, fs_type)
                                                s = sget(fs_type, test, set, flags, fs_info);
                                                  find sb in s_instances
                                                  grab_super(sb);
                                                    down_write(&s->s_umount); // blocks

      sop->put_super(sb)
        // sb->fs_devices->opened == 2; no-op
      spin_lock(&sb_lock);
      hlist_del_init(&sb->s_instances);
      spin_unlock(&sb_lock);
      up_write(&sb->s_umount);
                                                    return 0;
                                                  retry lookup
                                                  don't find sb in s_instances (deleted by CPU0)
                                                  s = alloc_super
                                                  return s;
                                                btrfs_fill_super(s, fs_devices, data)
                                                  open_ctree // fs_devices total_rw_bytes improperly set!
                                                    btrfs_read_chunk_tree
                                                      read_one_dev // increment total_rw_bytes again!!
                                                      super_total_bytes < fs_devices->total_rw_bytes // ERROR!!!

To fix this, we clear total_rw_bytes from within btrfs_read_chunk_tree before the calls to read_one_dev, while holding the sb umount semaphore and the uuid mutex.

To reproduce, it is sufficient to dirty a decent number of inodes, then quickly umount and mount.

  for i in $(seq 0 500)
  do
    dd if=/dev/zero of="/mnt/foo/$i" bs=1M count=1
  done
  umount /mnt/foo&
  mount /mnt/foo

does the trick for me.

---
 fs/btrfs/volumes.c |    8 ++++++++
 1 file changed, 8 insertions(+)

@@ -6902,6 +6902,14 @@ int btrfs_read_chunk_tree(struct btrfs_f
 	mutex_lock(&fs_info->chunk_mutex);
 
 	/*
+	 * It is possible for mount and umount to race in such a way that
+	 * we execute this code path, but open_fs_devices failed to clear
+	 * total_rw_bytes. We certainly want it cleared before reading the
+	 * device items, so clear it here.
+	 */
+	fs_info->fs_devices->total_rw_bytes = 0;
+
+	/*
 	 * Read all device items, and then all the chunk items. All
 	 * device items are found before any chunk item (their object id
 	 * is smaller than the lowest possible object id for a chunk

From: Robbie Ko <[email protected]>

commit 5909ca110b29aa16b23b52b8de8d3bb1035fd738 upstream.

When locking pages for delalloc, we check if it's dirty and mapping still matches. If it does not match, we need to return -EAGAIN and release all pages. Only the current page was put though, iterate over all the remaining pages too.

---
 fs/btrfs/extent_io.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

@@ -1721,7 +1721,8 @@ static int __process_pages_contig(struct
 				if (!PageDirty(pages[i]) ||
 				    pages[i]->mapping != mapping) {
 					unlock_page(pages[i]);
-					put_page(pages[i]);
+					for (; i < ret; i++)
+						put_page(pages[i]);
 					err = -EAGAIN;
 					goto out;
 				}

From: Vasundhara Volam <[email protected]>

[ Upstream commit 163e9ef63641a02de4c95cd921577265c52e1ce2 ]

The driver was modified to not rely on rtnl lock to protect link settings about 2 years ago. The pause setting was missed when making that change. Fix it by acquiring link_lock mutex before calling bnxt_hwrm_set_pause().

---
 drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

index 3c78cd1cdd6fb..6edbbfc1709a2 100644
@@ -1287,8 +1287,11 @@ static int bnxt_set_pauseparam(struct net_device *dev,
 	if (epause->tx_pause)
 		link_info->req_flow_ctrl |= BNXT_LINK_PAUSE_TX;
 
-	if (netif_running(dev))
+	if (netif_running(dev)) {
+		mutex_lock(&bp->link_lock);
 		rc = bnxt_hwrm_set_pause(bp);
+		mutex_unlock(&bp->link_lock);
+	}
 	return rc;
 }
 

2.25.1

From: Christophe JAILLET <[email protected]>

[ Upstream commit 3195c4706b00106aa82c73acd28340fa8fc2bfc1 ]

The size used when calling 'pci_alloc_consistent()' and 'pci_free_consistent()' should match.

Fix it and have it consistent with the corresponding call in 'rr_close()'.

---
 drivers/net/hippi/rrunner.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

index d7ba2b813effc..40ef4aeb0ef04 100644
@@ -1250,7 +1250,7 @@ static int rr_open(struct net_device *dev)
 		rrpriv->info = NULL;
 	}
 	if (rrpriv->rx_ctrl) {
-		pci_free_consistent(pdev, sizeof(struct ring_ctrl),
+		pci_free_consistent(pdev, 256 * sizeof(struct ring_ctrl),
 				    rrpriv->rx_ctrl, rrpriv->rx_ctrl_dma);
 		rrpriv->rx_ctrl = NULL;
 	}

2.25.1

From: George Kennedy <[email protected]>

[ Upstream commit c28d9a285668c799eeae2f7f93e929a6028a4d6d ]

If ax88172a_unbind() fails, make sure that the return code is less than zero so that cleanup is done properly and avoid UAF.

---
 drivers/net/usb/ax88172a.c | 1 +
 1 file changed, 1 insertion(+)

index 914cac55a7ae7..909755ef71ac3 100644
@@ -210,6 +210,7 @@ static int ax88172a_bind(struct usbnet *dev, struct usb_interface *intf)
 	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf, 0);
 	if (ret < ETH_ALEN) {
 		netdev_err(dev->net, "Failed to read MAC address: %d\n", ret);
+		ret = -EIO;
 		goto free;
 	}
 	memcpy(dev->net->dev_addr, buf, ETH_ALEN);

2.25.1

From: Sergey Organov <[email protected]>

[ Upstream commit 473309fb8372365ad211f425bca760af800e10a7 ]

A driver which supports hardware time stamping shall update the struct with the actual, possibly more permissive configuration.

Do update the struct passed when we upscale the requested time stamping mode.

---
 drivers/net/phy/dp83640.c | 4 ++++
 1 file changed, 4 insertions(+)

index c52c016676af3..5752280fdb408 100644
@@ -1339,6 +1339,7 @@ static int dp83640_hwtstamp(struct phy_device *phydev, struct ifreq *ifr)
 		dp83640->hwts_rx_en = 1;
 		dp83640->layer = PTP_CLASS_L4;
 		dp83640->version = PTP_CLASS_V1;
+		cfg.rx_filter = HWTSTAMP_FILTER_PTP_V1_L4_EVENT;
 		break;
 	case HWTSTAMP_FILTER_PTP_V2_L4_EVENT:
 	case HWTSTAMP_FILTER_PTP_V2_L4_SYNC:

@@ -1346,6 +1347,7 @@ static int dp83640_hwtstamp(struct phy_device *phydev, struct ifreq *ifr)
 		dp83640->hwts_rx_en = 1;
 		dp83640->layer = PTP_CLASS_L4;
 		dp83640->version = PTP_CLASS_V2;
+		cfg.rx_filter = HWTSTAMP_FILTER_PTP_V2_L4_EVENT;
 		break;
 	case HWTSTAMP_FILTER_PTP_V2_L2_EVENT:
 	case HWTSTAMP_FILTER_PTP_V2_L2_SYNC:

@@ -1353,6 +1355,7 @@ static int dp83640_hwtstamp(struct phy_device *phydev, struct ifreq *ifr)
 		dp83640->hwts_rx_en = 1;
 		dp83640->layer = PTP_CLASS_L2;
 		dp83640->version = PTP_CLASS_V2;
+		cfg.rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
 		break;
 	case HWTSTAMP_FILTER_PTP_V2_EVENT:
 	case HWTSTAMP_FILTER_PTP_V2_SYNC:

@@ -1360,6 +1363,7 @@ static int dp83640_hwtstamp(struct phy_device *phydev, struct ifreq *ifr)
 		dp83640->hwts_rx_en = 1;
 		dp83640->layer = PTP_CLASS_L4 | PTP_CLASS_L2;
 		dp83640->version = PTP_CLASS_V2;
+		cfg.rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT;
 		break;
 	default:
 		return -ERANGE;

2.25.1

From: Chen-Yu Tsai <[email protected]>

[ Upstream commit baa1841eb797eadce6c907bdaed7cd6f01815404 ]

When the extra HPD polling in sun4i_hdmi was removed, the result of HPD was accidentally inverted.

Fix this by inverting the check.

---
 drivers/gpu/drm/sun4i/sun4i_hdmi_enc.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

index 82cb939351889..c9f1a8cd5f2ac 100644
@@ -215,7 +215,7 @@ sun4i_hdmi_connector_detect(struct drm_connector *connector, bool force)
 	unsigned long reg;
 
 	reg = readl(hdmi->base + SUN4I_HDMI_HPD_REG);
-	if (reg & SUN4I_HDMI_HPD_HIGH) {
+	if (!(reg & SUN4I_HDMI_HPD_HIGH)) {
 		cec_phys_addr_invalidate(hdmi->cec_adap);
 		return connector_status_disconnected;
 	}

2.25.1

From: Wang Hai <[email protected]>

[ Upstream commit bca9749b1aa23d964d3ab930938af66dbf887f15 ]

If try_toggle_control_gpio() failed in smc_drv_probe(), free_netdev(ndev) should be called to free the ndev created earlier. Otherwise, a memleak will occur.

---
 drivers/net/ethernet/smsc/smc91x.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

index 96ac0d3af6f5b..f570a37c68c23 100644
@@ -2294,7 +2294,7 @@ static int smc_drv_probe(struct platform_device *pdev)
 		ret = try_toggle_control_gpio(&pdev->dev, &lp->power_gpio,
 					      "power", 0, 0, 100);
 		if (ret)
-			return ret;
+			goto out_free_netdev;
 
 		/*
 		 * Optional reset GPIO configured? Minimum 100 ns reset needed

@@ -2303,7 +2303,7 @@ static int smc_drv_probe(struct platform_device *pdev)
 		ret = try_toggle_control_gpio(&pdev->dev, &lp->reset_gpio,
 					      "reset", 0, 0, 100);
 		if (ret)
-			return ret;
+			goto out_free_netdev;
 
 		/*
 		 * Need to wait for optional EEPROM to load, max 750 us according

2.25.1

From: Taehee Yoo <[email protected]>

[ Upstream commit 544f287b84959203367cd29e16e772717612fab4 ]

If register_netdevice() is failed, net_device should not be used because variables are uninitialized or freed.
So, the routine should be stopped immediately.
But, bond_create() doesn't check return value of register_netdevice() immediately. That will result in a panic because of using uninitialized or freed memory.

Test commands:

    modprobe netdev-notifier-error-inject
    echo -22 > /sys/kernel/debug/notifier-error-inject/netdev/\

actions/NETDEV_REGISTER/error
modprobe bonding max_bonds=3

Splat looks like:

[  375.028492][  T193] general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b6b: 0000 [#1] SMP DEBUG_PAGEALLOC PTI
[  375.033207][  T193] CPU: 2 PID: 193 Comm: kworker/2:2 Not tainted 5.8.0-rc4+ #645
[  375.036068][  T193] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[  375.039673][  T193] Workqueue: events linkwatch_event
[  375.041557][  T193] RIP: 0010:dev_activate+0x4a/0x340
[  375.043381][  T193] Code: 40 a8 04 0f 85 db 00 00 00 8b 83 08 04 00 00 85 c0 0f 84 0d 01 00 00 31 d2 89 d0 48 8d 04 40 48 c1 e0 07 48 03 83 00 04 00 00 <48> 8b 48 10 f6 41 10 01 75 08 f0 80 a1 a0 01 00 00 fd 48 89 48 08
[  375.050267][  T193] RSP: 0018:ffff9f8facfcfdd8 EFLAGS: 00010202
[  375.052410][  T193] RAX: 6b6b6b6b6b6b6b6b RBX: ffff9f8fae6ea000 RCX: 0000000000000006
[  375.055178][  T193] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9f8fae6ea000
[  375.057762][  T193] RBP: ffff9f8fae6ea000 R08: 0000000000000000 R09: 0000000000000000
[  375.059810][  T193] R10: 0000000000000001 R11: 0000000000000000 R12: ffff9f8facfcfe08
[  375.061892][  T193] R13: ffffffff883587e0 R14: 0000000000000000 R15: ffff9f8fae6ea580
[  375.063931][  T193] FS:  0000000000000000(0000) GS:ffff9f8fbae00000(0000) knlGS:0000000000000000
[  375.066239][  T193] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  375.067841][  T193] CR2: 00007f2f542167a0 CR3: 000000012cee6002 CR4: 00000000003606e0
[  375.069657][  T193] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  375.071471][  T193] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  375.073269][  T193] Call Trace:
[  375.074005][  T193]  linkwatch_do_dev+0x4d/0x50
[  375.075052][  T193]  __linkwatch_run_queue+0x10b/0x200
[  375.076244][  T193]  linkwatch_event+0x21/0x30
[  375.077274][  T193]  process_one_work+0x252/0x600
[  375.078379][  T193]  ? process_one_work+0x600/0x600
[  375.079518][  T193]  worker_thread+0x3c/0x380
[  375.080534][  T193]  ? process_one_work+0x600/0x600
[  375.081668][  T193]  kthread+0x139/0x150
[  375.082567][  T193]  ? kthread_park+0x90/0x90
[  375.083567][  T193]  ret_from_fork+0x22/0x30

---
 drivers/net/bonding/bond_main.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)

index fef599eb822b6..1f867e275408e 100644
@@ -4773,15 +4773,19 @@ int bond_create(struct net *net, const char *name)
 	bond_dev->rtnl_link_ops = &bond_link_ops;
 
 	res = register_netdevice(bond_dev);
+	if (res < 0) {
+		free_netdev(bond_dev);
+		rtnl_unlock();
+
+		return res;
+	}
 
 	netif_carrier_off(bond_dev);
 
 	bond_work_init_all(bond);
 
 	rtnl_unlock();
-	if (res < 0)
-		free_netdev(bond_dev);
-	return res;
+	return 0;
 }
 
 static int __net_init bond_net_init(struct net *net)

2.25.1

From: Liu Jian <[email protected]>

[ Upstream commit 5dbaeb87f2b309936be0aeae00cbc9e7f20ab296 ]

When mlxsw_core_trap_register fails in mlxsw_emad_init, destroy_workqueue() shouled be called to destroy mlxsw_core->emad_wq.

---
 drivers/net/ethernet/mellanox/mlxsw/core.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

index fad26046e1595..96f9f267d16d4 100644
@@ -619,7 +619,7 @@ static int mlxsw_emad_init(struct mlxsw_core *mlxsw_core)
 	err = mlxsw_core_trap_register(mlxsw_core, &mlxsw_emad_rx_listener,
 				       mlxsw_core);
 	if (err)
-		return err;
+		goto err_trap_register;
 
 	err = mlxsw_core->driver->basic_trap_groups_set(mlxsw_core);
 	if (err)

@@ -631,6 +631,7 @@ static int mlxsw_emad_init(struct mlxsw_core *mlxsw_core)
 err_emad_trap_set:
 	mlxsw_core_trap_unregister(mlxsw_core, &mlxsw_emad_rx_listener,
 				   mlxsw_core);
+err_trap_register:
 	destroy_workqueue(mlxsw_core->emad_wq);
 	return err;
 }

2.25.1

From: guodeqing <[email protected]>

[ Upstream commit 8210e344ccb798c672ab237b1a4f241bda08909b ]

The sync_thread_backup only checks sk_receive_queue is empty or not, there is a situation which cannot sync the connection entries when sk_receive_queue is empty and sk_rmem_alloc is larger than sk_rcvbuf, the sync packets are dropped in __udp_enqueue_schedule_skb, this is because the packets in reader_queue is not read, so the rmem is not reclaimed.

Here I add the check of whether the reader_queue of the udp sock is empty or not to solve this problem.

---
 net/netfilter/ipvs/ip_vs_sync.c | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)

index b373e053ff9a3..90261055062ed 100644
@@ -1726,6 +1726,8 @@ static int sync_thread_backup(void *data)
 {
 	struct ip_vs_sync_thread_data *tinfo = data;
 	struct netns_ipvs *ipvs = tinfo->ipvs;
+	struct sock *sk = tinfo->sock->sk;
+	struct udp_sock *up = udp_sk(sk);
 	int len;
 
 	pr_info("sync thread started: state = BACKUP, mcast_ifn = %s, "

@@ -1733,12 +1735,14 @@ static int sync_thread_backup(void *data)
 		ipvs->bcfg.mcast_ifn, ipvs->bcfg.syncid, tinfo->id);
 
 	while (!kthread_should_stop()) {
-		wait_event_interruptible(*sk_sleep(tinfo->sock->sk),
-			 !skb_queue_empty(&tinfo->sock->sk->sk_receive_queue)
-			 || kthread_should_stop());
+		wait_event_interruptible(*sk_sleep(sk),
+					 !skb_queue_empty_lockless(&sk->sk_receive_queue) ||
+					 !skb_queue_empty_lockless(&up->reader_queue) ||
+					 kthread_should_stop());
 
 		/* do we have data now? */
-		while (!skb_queue_empty(&(tinfo->sock->sk->sk_receive_queue))) {
+		while (!skb_queue_empty_lockless(&sk->sk_receive_queue) ||
+		       !skb_queue_empty_lockless(&up->reader_queue)) {
 			len = ip_vs_receive(tinfo->sock, tinfo->buf,
 					ipvs->bcfg.sync_maxlen);
 			if (len <= 0) {

2.25.1

From: Wolfram Sang <[email protected]>

[ Upstream commit eb01597158ffb1853a7a7fc2c57d4c844640f75e ]

On R-Car Gen2, we get a timeout when reading from the address set in ICSAR, even though the slave interface is disabled. Clearing it fixes this situation. Note that Gen3 is not affected.

To reproduce: bind and undbind an I2C slave on some bus, run 'i2cdetect' on that bus.

---
 drivers/i2c/busses/i2c-rcar.c | 3 +++
 1 file changed, 3 insertions(+)

index 132c4a405bf83..db9ca8e926ca7 100644
@@ -817,6 +817,7 @@ static int rcar_unreg_slave(struct i2c_client *slave)
 	/* disable irqs and ensure none is running before clearing ptr */
 	rcar_i2c_write(priv, ICSIER, 0);
 	rcar_i2c_write(priv, ICSCR, 0);
+	rcar_i2c_write(priv, ICSAR, 0); /* Gen2: must be 0 if not using slave */
 
 	synchronize_irq(priv->irq);
 	priv->slave = NULL;

@@ -914,6 +915,8 @@ static int rcar_i2c_probe(struct platform_device *pdev)
 	if (ret < 0)
 		goto out_pm_put;
 
+	rcar_i2c_write(priv, ICSAR, 0); /* Gen2: must be 0 if not using slave */
+
 	if (priv->devtype == I2C_RCAR_GEN3) {
 		priv->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
 		if (!IS_ERR(priv->rstc)) {

2.25.1

From: Cong Wang <[email protected]>

[ Upstream commit c75d1d5248c0c97996051809ad0e9f154ba5d76e ]

Very similar to commit 544f287b8495
("bonding: check error value of register_netdevice() immediately"), we should immediately check the return value of register_netdevice() before doing anything else.

---
 drivers/net/bonding/bond_netlink.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

index 77babf1417a7e..0e95eeb822ea5 100644
@@ -451,11 +451,10 @@ static int bond_newlink(struct net *src_net, struct net_device *bond_dev,
 		return err;
 
 	err = register_netdevice(bond_dev);
-
-	netif_carrier_off(bond_dev);
 	if (!err) {
 		struct bonding *bond = netdev_priv(bond_dev);
 
+		netif_carrier_off(bond_dev);
 		bond_work_init_all(bond);
 	}
 

2.25.1

From: Matthew Howell <[email protected]>

[ Upstream commit 5fdbe136ae19ab751daaa4d08d9a42f3e30d17f9 ]

Sealevel XR17V35X based devices are inoperable on kernel versions 4.11 and above due to a change in the GPIO preconfiguration introduced in commit
7dea8165f1d. This patch fixes this by preconfiguring the GPIO on Sealevel cards to the value (0x00) used prior to commit 7dea8165f1d

With GPIOs preconfigured as per commit 7dea8165f1d all ports on Sealevel XR17V35X based devices become stuck in high impedance mode, regardless of dip-switch or software configuration. This causes the device to become effectively unusable. This patch (in various forms) has been distributed to our customers and no issues related to it have been reported.

---
 drivers/tty/serial/8250/8250_exar.c | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)

index 899f36b59af79..ed81128bb42e0 100644
@@ -229,7 +229,17 @@ static void setup_gpio(struct pci_dev *pcidev, u8 __iomem *p)
 	 * devices will export them as GPIOs, so we pre-configure them safely
 	 * as inputs.
 	 */
-	u8 dir = pcidev->vendor == PCI_VENDOR_ID_EXAR ? 0xff : 0x00;
+
+	u8 dir = 0x00;
+
+	if  ((pcidev->vendor == PCI_VENDOR_ID_EXAR) &&
+		(pcidev->subsystem_vendor != PCI_VENDOR_ID_SEALEVEL)) {
+		// Configure GPIO as inputs for Commtech adapters
+		dir = 0xff;
+	} else {
+		// Configure GPIO as outputs for SeaLevel adapters
+		dir = 0x00;
+	}
 
 	writeb(0x00, p + UART_EXAR_MPIOINT_7_0);
 	writeb(0x00, p + UART_EXAR_MPIOLVL_7_0);

2.25.1

From: Pi-Hsun Shih <[email protected]>

[ Upstream commit d178770d8d21489abf5bafefcbb6d5243b482e9a ]

Currently the basepath is removed only from the beginning of the string. When the symbol is inlined and there's multiple line outputs of addr2line, only the first line would have basepath removed.

Change to remove the basepath prefix from all lines.

---
 scripts/decode_stacktrace.sh | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

index 5aa75a0a1cede..946735bd5a252 100755
@@ -77,8 +77,8 @@ parse_symbol() {
 		return
 	fi
 
-	# Strip out the base of the path
-	code=${code#$basepath/}
+	# Strip out the base of the path on each line
+	code=$(while read -r line; do echo "${line#$basepath/}"; done <<< "$code")
 
 	# In the case of inlines, move everything to same line
 	code=${code//$'\n'/' '}

2.25.1

From: Federico Ricchiuto <[email protected]>

[ Upstream commit 43e666acb79f3d355dd89bf20f4d25d3b15da13e ]

The Mediacom FlexBook edge13 uses the SIPODEV SP1064 touchpad, which does not supply descriptors, so it has to be added to the override list.

---
 drivers/hid/i2c-hid/i2c-hid-dmi-quirks.c | 8 ++++++++
 1 file changed, 8 insertions(+)

index 681ac9bc68b3d..f98c1e1b1dbdc 100644
@@ -373,6 +373,14 @@ static const struct dmi_system_id i2c_hid_dmi_desc_override_table[] = {
 		},
 		.driver_data = (void *)&sipodev_desc
 	},
+	{
+		.ident = "Mediacom FlexBook edge 13",
+		.matches = {
+			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "MEDIACOM"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "FlexBook_edge13-M-FBE13"),
+		},
+		.driver_data = (void *)&sipodev_desc
+	},
 	{
 		.ident = "Odys Winbook 13",
 		.matches = {

2.25.1

From: Hans de Goede <[email protected]>

[ Upstream commit a5d81646fa294eed57786a9310b06ca48902adf8 ]

The Maxxter KB-BT-001 Bluetooth keyboard, which looks somewhat like the Apple Wireless Keyboard, is using the vendor and product IDs (05AC:0239) of the Apple Wireless Keyboard (2009 ANSI version) <sigh>.

But its F1 - F10 keys are marked as sending F1 - F10, not the special functions hid-apple.c maps them too; and since its descriptors do not contain the HID_UP_CUSTOM | 0x0003 usage apple-hid looks for for the Fn-key, apple_setup_input() never gets called, so F1 - F6 are mapped to key-codes which have not been set in the keybit array causing them to not send any events at all.

The lack of a usage code matching the Fn key in the clone is actually useful as this allows solving this problem in a generic way.

This commits adds a fn_found flag and it adds a input_configured callback which checks if this flag is set once all usages have been mapped. If it is not set, then assume this is a clone and clear the quirks bitmap so that the hid-apple code does not add any special handling to this keyboard.

This fixes F1 - F6 not sending anything at all and F7 - F12 sending the wrong codes on the Maxxter KB-BT-001 Bluetooth keyboard and on similar clones.

---
 drivers/hid/hid-apple.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

index 8ab8f2350bbcd..b58ab769aa7b3 100644
@@ -57,6 +57,7 @@ MODULE_PARM_DESC(swap_opt_cmd, "Swap the Option (\"Alt\") and Command (\"Flag\")
 struct apple_sc {
 	unsigned long quirks;
 	unsigned int fn_on;
+	unsigned int fn_found;
 	DECLARE_BITMAP(pressed_numlock, KEY_CNT);
 };
 

@@ -342,12 +343,15 @@ static int apple_input_mapping(struct hid_device *hdev, struct hid_input *hi,
 		struct hid_field *field, struct hid_usage *usage,
 		unsigned long **bit, int *max)
 {
+	struct apple_sc *asc = hid_get_drvdata(hdev);
+
 	if (usage->hid == (HID_UP_CUSTOM | 0x0003) ||
 			usage->hid == (HID_UP_MSVENDOR | 0x0003) ||
 			usage->hid == (HID_UP_HPVENDOR2 | 0x0003)) {
 		/* The fn key on Apple USB keyboards */
 		set_bit(EV_REP, hi->input->evbit);
 		hid_map_usage_clear(hi, usage, bit, max, EV_KEY, KEY_FN);
+		asc->fn_found = true;
 		apple_setup_input(hi->input);
 		return 1;
 	}

@@ -374,6 +378,19 @@ static int apple_input_mapped(struct hid_device *hdev, struct hid_input *hi,
 	return 0;
 }
 
+static int apple_input_configured(struct hid_device *hdev,
+		struct hid_input *hidinput)
+{
+	struct apple_sc *asc = hid_get_drvdata(hdev);
+
+	if ((asc->quirks & APPLE_HAS_FN) && !asc->fn_found) {
+		hid_info(hdev, "Fn key not found (Apple Wireless Keyboard clone?), disabling Fn key handling\n");
+		asc->quirks = 0;
+	}
+
+	return 0;
+}
+
 static int apple_probe(struct hid_device *hdev,
 		const struct hid_device_id *id)
 {

@@ -588,6 +605,7 @@ static struct hid_driver apple_driver = {
 	.event = apple_event,
 	.input_mapping = apple_input_mapping,
 	.input_mapped = apple_input_mapped,
+	.input_configured = apple_input_configured,
 };
 module_hid_driver(apple_driver);
 

2.25.1

From: Dinghao Liu <[email protected]>

[ Upstream commit 5b78fac4b1ba731cf4177fdbc1e3a4661521bcd0 ]

pm_runtime_get_sync() increments the runtime PM usage counter even when it returns an error code. Thus a pairing decrement is needed on the error handling path to keep the counter balanced.

---
 drivers/dma/tegra210-adma.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

index 045351f3549c1..86b45198fb962 100644
@@ -583,6 +583,7 @@ static int tegra_adma_alloc_chan_resources(struct dma_chan *dc)
 
 	ret = pm_runtime_get_sync(tdc2dev(tdc));
 	if (ret < 0) {
+		pm_runtime_put_noidle(tdc2dev(tdc));
 		free_irq(tdc->irq, tdc);
 		return ret;
 	}

@@ -764,8 +765,10 @@ static int tegra_adma_probe(struct platform_device *pdev)
 	pm_runtime_enable(&pdev->dev);
 
 	ret = pm_runtime_get_sync(&pdev->dev);
-	if (ret < 0)
+	if (ret < 0) {
+		pm_runtime_put_noidle(&pdev->dev);
 		goto rpm_disable;
+	}
 
 	ret = tegra_adma_init(tdma);
 	if (ret)

2.25.1

From: Merlijn Wajer <[email protected]>

[ Upstream commit c463bb2a8f8d7d97aa414bf7714fc77e9d3b10df ]

This event code represents the state of a removable cover of a device. Value 0 means that the cover is open or removed, value 1 means that the cover is closed.

---
 include/linux/mod_devicetable.h        | 2 +-
 include/uapi/linux/input-event-codes.h | 3 ++-
 2 files changed, 3 insertions(+), 2 deletions(-)

index eba777807fc04..6f8eb1238235f 100644
@@ -293,7 +293,7 @@ struct pcmcia_device_id {
 #define INPUT_DEVICE_ID_LED_MAX		0x0f
 #define INPUT_DEVICE_ID_SND_MAX		0x07
 #define INPUT_DEVICE_ID_FF_MAX		0x7f
-#define INPUT_DEVICE_ID_SW_MAX		0x0f
+#define INPUT_DEVICE_ID_SW_MAX		0x10
 #define INPUT_DEVICE_ID_PROP_MAX	0x1f
 
 #define INPUT_DEVICE_ID_MATCH_BUS	1

index 61769d4b7dbac..bce76e55a3c82 100644
@@ -793,7 +793,8 @@
 #define SW_LINEIN_INSERT	0x0d  /* set = inserted */
 #define SW_MUTE_DEVICE		0x0e  /* set = device disabled */
 #define SW_PEN_INSERTED		0x0f  /* set = pen inserted */
-#define SW_MAX			0x0f
+#define SW_MACHINE_COVER	0x10  /* set = cover closed */
+#define SW_MAX			0x10
 #define SW_CNT			(SW_MAX+1)
 
 /*

2.25.1

From: leilk.liu <[email protected]>

[ Upstream commit 44b37eb79e16a56cb30ba55b2da452396b941e7a ]

this patch use correct SPI_CFG2_REG offset.

---
 drivers/spi/spi-mt65xx.c | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)

index 0c2867deb36fc..da28c52c9da19 100644
@@ -41,7 +41,6 @@
 #define SPI_CFG0_SCK_LOW_OFFSET           8
 #define SPI_CFG0_CS_HOLD_OFFSET           16
 #define SPI_CFG0_CS_SETUP_OFFSET          24
-#define SPI_ADJUST_CFG0_SCK_LOW_OFFSET    16
 #define SPI_ADJUST_CFG0_CS_HOLD_OFFSET    0
 #define SPI_ADJUST_CFG0_CS_SETUP_OFFSET   16
 

@@ -53,6 +52,8 @@
 #define SPI_CFG1_CS_IDLE_MASK             0xff
 #define SPI_CFG1_PACKET_LOOP_MASK         0xff00
 #define SPI_CFG1_PACKET_LENGTH_MASK       0x3ff0000
+#define SPI_CFG2_SCK_HIGH_OFFSET          0
+#define SPI_CFG2_SCK_LOW_OFFSET           16
 
 #define SPI_CMD_ACT                  BIT(0)
 #define SPI_CMD_RESUME               BIT(1)

@@ -259,7 +260,7 @@ static void mtk_spi_set_cs(struct spi_device *spi, bool enable)
 static void mtk_spi_prepare_transfer(struct spi_master *master,
 				     struct spi_transfer *xfer)
 {
-	u32 spi_clk_hz, div, sck_time, cs_time, reg_val = 0;
+	u32 spi_clk_hz, div, sck_time, cs_time, reg_val;
 	struct mtk_spi *mdata = spi_master_get_devdata(master);
 
 	spi_clk_hz = clk_get_rate(mdata->spi_clk);

@@ -272,18 +273,18 @@ static void mtk_spi_prepare_transfer(struct spi_master *master,
 	cs_time = sck_time * 2;
 
 	if (mdata->dev_comp->enhance_timing) {
+		reg_val = (((sck_time - 1) & 0xffff)
+			   << SPI_CFG2_SCK_HIGH_OFFSET);
 		reg_val |= (((sck_time - 1) & 0xffff)
-			   << SPI_CFG0_SCK_HIGH_OFFSET);
-		reg_val |= (((sck_time - 1) & 0xffff)
-			   << SPI_ADJUST_CFG0_SCK_LOW_OFFSET);
+			   << SPI_CFG2_SCK_LOW_OFFSET);
 		writel(reg_val, mdata->base + SPI_CFG2_REG);
-		reg_val |= (((cs_time - 1) & 0xffff)
+		reg_val = (((cs_time - 1) & 0xffff)
 			   << SPI_ADJUST_CFG0_CS_HOLD_OFFSET);
 		reg_val |= (((cs_time - 1) & 0xffff)
 			   << SPI_ADJUST_CFG0_CS_SETUP_OFFSET);
 		writel(reg_val, mdata->base + SPI_CFG0_REG);
 	} else {
-		reg_val |= (((sck_time - 1) & 0xff)
+		reg_val = (((sck_time - 1) & 0xff)
 			   << SPI_CFG0_SCK_HIGH_OFFSET);
 		reg_val |= (((sck_time - 1) & 0xff) << SPI_CFG0_SCK_LOW_OFFSET);
 		reg_val |= (((cs_time - 1) & 0xff) << SPI_CFG0_CS_HOLD_OFFSET);

2.25.1

From: Marc Kleine-Budde <[email protected]>

[ Upstream commit e84861fec32dee8a2e62bbaa52cded6b05a2a456 ]

This function is used by dev_get_regmap() to retrieve a regmap for the specified device. If the device has more than one regmap, the name parameter can be used to specify one.

The code here uses a pointer comparison to check for equal strings. This however will probably always fail, as the regmap->name is allocated via kstrdup_const() from the regmap's config->name.

Fix this by using strcmp() instead.

---
 drivers/base/regmap/regmap.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

index 013d0a2b3ba0a..4e0cc40ad9ceb 100644
@@ -1242,7 +1242,7 @@ static int dev_get_regmap_match(struct device *dev, void *res, void *data)
 
 	/* If the user didn't specify a name match any */
 	if (data)
-		return (*r)->name == data;
+		return !strcmp((*r)->name, data);
 	else
 		return 1;
 }

2.25.1

From: Evgeny Novikov <[email protected]>

[ Upstream commit bc4071aafcf4d0535ee423b69167696d6c03207d ]

aspeed_create_fan() reads a pwm_port value using of_property_read_u32(). If pwm_port will be more than ARRAY_SIZE(pwm_port_params), there will be a buffer overflow in aspeed_create_pwm_port()->aspeed_set_pwm_port_enable(). The patch fixes the potential buffer overflow.

Found by Linux Driver Verification project (linuxtesting.org).

---
 drivers/hwmon/aspeed-pwm-tacho.c | 2 ++
 1 file changed, 2 insertions(+)

index 69b97d45e3cbb..e4337e9dda444 100644
@@ -878,6 +878,8 @@ static int aspeed_create_fan(struct device *dev,
 	ret = of_property_read_u32(child, "reg", &pwm_port);
 	if (ret)
 		return ret;
+	if (pwm_port >= ARRAY_SIZE(pwm_port_params))
+		return -EINVAL;
 	aspeed_create_pwm_port(priv, (u8)pwm_port);
 
 	ret = of_property_count_u8_elems(child, "cooling-levels");

2.25.1

From: Leonid Ravich <[email protected]>

[ Upstream commit 87730ccbddcb48478b1b88e88b14e73424130764 ]

DMA transaction time to completion is a function of PCI bandwidth, transaction size and a queue depth. So hard coded value for timeouts might be wrong for some scenarios.

---
 drivers/dma/ioat/dma.c | 12 ++++++++++++
 drivers/dma/ioat/dma.h |  2 --
 2 files changed, 12 insertions(+), 2 deletions(-)

index e3899ae429e0f..4c2b41beaf638 100644
@@ -38,6 +38,18 @@
 
 #include "../dmaengine.h"
 
+int completion_timeout = 200;
+module_param(completion_timeout, int, 0644);
+MODULE_PARM_DESC(completion_timeout,
+		"set ioat completion timeout [msec] (default 200 [msec])");
+int idle_timeout = 2000;
+module_param(idle_timeout, int, 0644);
+MODULE_PARM_DESC(idle_timeout,
+		"set ioat idel timeout [msec] (default 2000 [msec])");
+
+#define IDLE_TIMEOUT msecs_to_jiffies(idle_timeout)
+#define COMPLETION_TIMEOUT msecs_to_jiffies(completion_timeout)
+
 static char *chanerr_str[] = {
 	"DMA Transfer Source Address Error",
 	"DMA Transfer Destination Address Error",

index 56200eefcf5ee..01f9299572303 100644
@@ -111,8 +111,6 @@ struct ioatdma_chan {
 	#define IOAT_RUN 5
 	#define IOAT_CHAN_ACTIVE 6
 	struct timer_list timer;
-	#define COMPLETION_TIMEOUT msecs_to_jiffies(100)
-	#define IDLE_TIMEOUT msecs_to_jiffies(2000)
 	#define RESET_DELAY msecs_to_jiffies(100)
 	struct ioatdma_device *ioat_dma;
 	dma_addr_t completion_dma;

2.25.1

From: Ilya Katsnelson <[email protected]>

[ Upstream commit dcb00fc799dc03fd320e123e4c81b3278c763ea5 ]

Tested on my own laptop, touchpad feels slightly more responsive with this on, though it might just be placebo.

---
 drivers/input/mouse/synaptics.c | 1 +
 1 file changed, 1 insertion(+)

index 85db184321f78..0714d572e49a3 100644
@@ -182,6 +182,7 @@ static const char * const smbus_pnp_ids[] = {
 	"LEN0093", /* T480 */
 	"LEN0096", /* X280 */
 	"LEN0097", /* X280 -> ALPS trackpoint */
+	"LEN0099", /* X1 Extreme 1st */
 	"LEN009b", /* T580 */
 	"LEN200f", /* T450s */
 	"LEN2044", /* L470  */

2.25.1

From: Evgeny Novikov <[email protected]>

[ Upstream commit c8f8529e2c4141afa2ebb487ad48e8a6ec3e8c99 ]

gr_ep_init() does not assign the allocated request anywhere if allocation of memory for the buffer fails. This is a memory leak fixed by the given patch.

Found by Linux Driver Verification project (linuxtesting.org).

---
 drivers/usb/gadget/udc/gr_udc.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

index feb73a1c42ef9..be094f4e116b1 100644
@@ -2000,9 +2000,12 @@ static int gr_ep_init(struct gr_udc *dev, int num, int is_in, u32 maxplimit)
 
 	if (num == 0) {
 		_req = gr_alloc_request(&ep->ep, GFP_ATOMIC);
+		if (!_req)
+			return -ENOMEM;
+
 		buf = devm_kzalloc(dev->dev, PAGE_SIZE, GFP_DMA | GFP_ATOMIC);
-		if (!_req || !buf) {
-			/* possible _req freed by gr_probe via gr_remove */
+		if (!buf) {
+			gr_free_request(&ep->ep, _req);
 			return -ENOMEM;
 		}
 

2.25.1

From: Will Deacon <[email protected]>

[ Upstream commit 5afc78551bf5d53279036e0bf63314e35631d79f ]

Rather than open-code test_tsk_thread_flag() at each callsite, simply replace the couple of offenders with calls to test_tsk_thread_flag() directly.

---
 arch/arm64/kernel/debug-monitors.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

index db7ed460a5476..2ccd0a99d8b35 100644
@@ -389,14 +389,14 @@ void user_rewind_single_step(struct task_struct *task)
 	 * If single step is active for this thread, then set SPSR.SS
 	 * to 1 to avoid returning to the active-pending state.
 	 */
-	if (test_ti_thread_flag(task_thread_info(task), TIF_SINGLESTEP))
+	if (test_tsk_thread_flag(task, TIF_SINGLESTEP))
 		set_regs_spsr_ss(task_pt_regs(task));
 }
 NOKPROBE_SYMBOL(user_rewind_single_step);
 
 void user_fastforward_single_step(struct task_struct *task)
 {
-	if (test_ti_thread_flag(task_thread_info(task), TIF_SINGLESTEP))
+	if (test_tsk_thread_flag(task, TIF_SINGLESTEP))
 		clear_regs_spsr_ss(task_pt_regs(task));
 }
 

2.25.1

From: Arnd Bergmann <[email protected]>

[ Upstream commit 81e96851ea32deb2c921c870eecabf335f598aeb ]

The clang integrated assembler requires the 'cmp' instruction to have a length prefix here:

arch/x86/math-emu/wm_sqrt.S:212:2: error: ambiguous instructions require an explicit suffix (could be 'cmpb', 'cmpw', or 'cmpl')
cmp $0xffffffff,-24(%ebp)
^

Make this a 32-bit comparison, which it was clearly meant to be.

---
 arch/x86/math-emu/wm_sqrt.S | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

index f031c0e193565..515cdee90df72 100644
@@ -209,7 +209,7 @@ sqrt_stage_2_finish:
 
 #ifdef PARANOID
 /* It should be possible to get here only if the arg is ffff....ffff */
-	cmp	$0xffffffff,FPU_fsqrt_arg_1
+	cmpl	$0xffffffff,FPU_fsqrt_arg_1
 	jnz	sqrt_stage_2_error
 #endif /* PARANOID */
 

2.25.1

From: Tetsuo Handa <[email protected]>

commit f867c771f98891841c217fa8459244ed0dd28921 upstream.

syzbot is reporting that mmput() from shrinker function has a risk of deadlock [1], for delayed_uprobe_add() from update_ref_ctr() calls kzalloc(GFP_KERNEL) with delayed_uprobe_lock held, and uprobe_clear_state() from __mmput() also holds delayed_uprobe_lock.

Commit a1b2289cef92ef0e ("android: binder: drop lru lock in isolate callback") replaced mmput() with mmput_async() in order to avoid sleeping with spinlock held. But this patch replaces mmput() with mmput_async() in order not to start __mmput() from shrinker context.

[1] https://syzkaller.appspot.com/bug?id=bc9e7303f537c41b2b0cc2dfcea3fc42964c2d45

---
 drivers/android/binder_alloc.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -968,7 +968,7 @@ enum lru_status binder_alloc_free_page(s
 		trace_binder_unmap_user_end(alloc, index);
 	}
 	up_read(&mm->mmap_sem);
-	mmput(mm);
+	mmput_async(mm);
 
 	trace_binder_unmap_kernel_start(alloc, index);
 

From: Chunfeng Yun <[email protected]>

commit 5ce1a24dd98c00a57a8fa13660648abf7e08e3ef upstream.

The wMaxPacketSize field of endpoint descriptor may be zero as default value in alternate interface, and they are not actually selected when start stream, so skip them when try to allocate bandwidth.

---
 drivers/usb/host/xhci-mtk-sch.c |    4 ++++
 1 file changed, 4 insertions(+)

@@ -284,6 +284,10 @@ static bool need_bw_sch(struct usb_host_
 	if (is_fs_or_ls(speed) && !has_tt)
 		return false;
 
+	/* skip endpoint with zero maxpkt */
+	if (usb_endpoint_maxp(&ep->desc) == 0)
+		return false;
+
 	return true;
 }
 

From: Forest Crossman <[email protected]>

commit dbb0897e805f2ab1b8bc358f6c3d878a376b8897 upstream.

The ASM2142/ASM3142 (same PCI IDs) does not support full 64-bit DMA addresses, which can cause silent memory corruption or IOMMU errors on platforms that use the upper bits. Add the XHCI_NO_64BIT_SUPPORT quirk to fix this issue.

---
 drivers/usb/host/xhci-pci.c |    3 +++
 1 file changed, 3 insertions(+)

@@ -235,6 +235,9 @@ static void xhci_pci_quirks(struct devic
 	if (pdev->vendor == PCI_VENDOR_ID_ASMEDIA &&
 			pdev->device == 0x1142)
 		xhci->quirks |= XHCI_TRUST_TX_LENGTH;
+	if (pdev->vendor == PCI_VENDOR_ID_ASMEDIA &&
+			pdev->device == 0x2142)
+		xhci->quirks |= XHCI_NO_64BIT_SUPPORT;
 
 	if (pdev->vendor == PCI_VENDOR_ID_ASMEDIA &&
 		pdev->device == PCI_DEVICE_ID_ASMEDIA_1042A_XHCI)

From: Steve French <[email protected]>

commit 0e6705182d4e1b77248a93470d6d7b3013d59b30 upstream.

This reverts commit 9ffad9263b467efd8f8dc7ae1941a0a655a2bab2.

Upon additional testing with older servers, it was found that the original commit introduced a regression when using the old SMB1 dialect and rsyncing over an existing file.

The patch will need to be respun to address this, likely including a larger refactoring of the SMB1 and SMB3 rename code paths to make it less confusing and also to address some additional rename error cases that SMB3 may be able to workaround.

---
 fs/cifs/inode.c |   10 ++--------
 1 file changed, 2 insertions(+), 8 deletions(-)

@@ -1778,7 +1778,6 @@ cifs_rename2(struct inode *source_dir, s
 	FILE_UNIX_BASIC_INFO *info_buf_target;
 	unsigned int xid;
 	int rc, tmprc;
-	bool new_target = d_really_is_negative(target_dentry);
 
 	if (flags & ~RENAME_NOREPLACE)
 		return -EINVAL;

@@ -1855,13 +1854,8 @@ cifs_rename2(struct inode *source_dir, s
 	 */
 
 unlink_target:
-	/*
-	 * If the target dentry was created during the rename, try
-	 * unlinking it if it's not negative
-	 */
-	if (new_target &&
-	    d_really_is_positive(target_dentry) &&
-	    (rc == -EACCES || rc == -EEXIST)) {
+	/* Try unlinking the target dentry if it's not negative */
+	if (d_really_is_positive(target_dentry) && (rc == -EACCES || rc == -EEXIST)) {
 		if (d_is_dir(target_dentry))
 			tmprc = cifs_rmdir(target_dir, target_dentry);
 		else

From: Rustam Kovhaev <[email protected]>

commit faaff9765664009c1c7c65551d32e9ed3b1dda8f upstream.

As syzkaller detected, wlan-ng driver does not do sanity check of endpoints in prism2sta_probe_usb(), add check for xfer direction and type

---
 drivers/staging/wlan-ng/prism2usb.c |   16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)

@@ -61,11 +61,25 @@ static int prism2sta_probe_usb(struct us
 			       const struct usb_device_id *id)
 {
 	struct usb_device *dev;
-
+	const struct usb_endpoint_descriptor *epd;
+	const struct usb_host_interface *iface_desc = interface->cur_altsetting;
 	struct wlandevice *wlandev = NULL;
 	struct hfa384x *hw = NULL;
 	int result = 0;
 
+	if (iface_desc->desc.bNumEndpoints != 2) {
+		result = -ENODEV;
+		goto failed;
+	}
+
+	result = -EINVAL;
+	epd = &iface_desc->endpoint[1].desc;
+	if (!usb_endpoint_is_bulk_in(epd))
+		goto failed;
+	epd = &iface_desc->endpoint[2].desc;
+	if (!usb_endpoint_is_bulk_out(epd))
+		goto failed;
+
 	dev = interface_to_usbdev(interface);
 	wlandev = create_wlan();
 	if (!wlandev) {

From: Ian Abbott <[email protected]>

commit 0bd0db42a030b75c20028c7ba6e327b9cb554116 upstream.

The INSN_CONFIG comedi instruction with sub-instruction code INSN_CONFIG_DIGITAL_TRIG includes a base channel in data[3]. This is used as a right shift amount for other bitmask values without being checked. Shift amounts greater than or equal to 32 will result in undefined behavior. Add code to deal with this.

---
 drivers/staging/comedi/drivers/addi_apci_1032.c |   20 ++++++++++++++------
 1 file changed, 14 insertions(+), 6 deletions(-)

@@ -115,14 +115,22 @@ static int apci1032_cos_insn_config(stru
 				    unsigned int *data)
 {
 	struct apci1032_private *devpriv = dev->private;
-	unsigned int shift, oldmask;
+	unsigned int shift, oldmask, himask, lomask;
 
 	switch (data[0]) {
 	case INSN_CONFIG_DIGITAL_TRIG:
 		if (data[1] != 0)
 			return -EINVAL;
 		shift = data[3];
-		oldmask = (1U << shift) - 1;
+		if (shift < 32) {
+			oldmask = (1U << shift) - 1;
+			himask = data[4] << shift;
+			lomask = data[5] << shift;
+		} else {
+			oldmask = 0xffffffffu;
+			himask = 0;
+			lomask = 0;
+		}
 		switch (data[2]) {
 		case COMEDI_DIGITAL_TRIG_DISABLE:
 			devpriv->ctrl = 0;

@@ -145,8 +153,8 @@ static int apci1032_cos_insn_config(stru
 				devpriv->mode2 &= oldmask;
 			}
 			/* configure specified channels */
-			devpriv->mode1 |= data[4] << shift;
-			devpriv->mode2 |= data[5] << shift;
+			devpriv->mode1 |= himask;
+			devpriv->mode2 |= lomask;
 			break;
 		case COMEDI_DIGITAL_TRIG_ENABLE_LEVELS:
 			if (devpriv->ctrl != (APCI1032_CTRL_INT_ENA |

@@ -163,8 +171,8 @@ static int apci1032_cos_insn_config(stru
 				devpriv->mode2 &= oldmask;
 			}
 			/* configure specified channels */
-			devpriv->mode1 |= data[4] << shift;
-			devpriv->mode2 |= data[5] << shift;
+			devpriv->mode1 |= himask;
+			devpriv->mode2 |= lomask;
 			break;
 		default:
 			return -EINVAL;

From: Ian Abbott <[email protected]>

commit f07804ec77d77f8a9dcf570a24154e17747bc82f upstream.

ni6527_intr_insn_config() processes INSN_CONFIG comedi instructions for the "interrupt" subdevice. When data[0] is INSN_CONFIG_DIGITAL_TRIG it is configuring the digital trigger. When data[2] is COMEDI_DIGITAL_TRIG_ENABLE_EDGES it is configuring rising and falling edge detection for the digital trigger, using a base channel number (or shift amount) in data[3], a rising edge bitmask in data[4] and falling edge bitmask in data[5].

If the base channel number (shift amount) is greater than or equal to the number of channels (24) of the digital input subdevice, there are no changes to the rising and falling edges, so the mask of channels to be changed can be set to 0, otherwise the mask of channels to be changed, and the rising and falling edge bitmasks are shifted by the base channel number before calling ni6527_set_edge_detection() to change the appropriate registers. Unfortunately, the code is comparing the base channel (shift amount) to the interrupt subdevice's number of channels
(1) instead of the digital input subdevice's number of channels (24). Fix it by comparing to 32 because all shift amounts for an unsigned int must be less than that and everything from bit 24 upwards is ignored by ni6527_set_edge_detection() anyway.

---
 drivers/staging/comedi/drivers/ni_6527.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -341,7 +341,7 @@ static int ni6527_intr_insn_config(struc
 		case COMEDI_DIGITAL_TRIG_ENABLE_EDGES:
 			/* check shift amount */
 			shift = data[3];
-			if (shift >= s->n_chan) {
+			if (shift >= 32) {
 				mask = 0;
 				rising = 0;
 				falling = 0;

From: Ian Abbott <[email protected]>

commit fc846e9db67c7e808d77bf9e2ef3d49e3820ce5d upstream.

The INSN_CONFIG comedi instruction with sub-instruction code INSN_CONFIG_DIGITAL_TRIG includes a base channel in data[3]. This is used as a right shift amount for other bitmask values without being checked. Shift amounts greater than or equal to 32 will result in undefined behavior. Add code to deal with this, adjusting the checks for invalid channels so that enabled channel bits that would have been lost by shifting are also checked for validity. Only channels 0 to 15 are valid.

---
 drivers/staging/comedi/drivers/addi_apci_1500.c |   24 +++++++++++++++++++-----
 1 file changed, 19 insertions(+), 5 deletions(-)

@@ -461,13 +461,14 @@ static int apci1500_di_cfg_trig(struct c
 	struct apci1500_private *devpriv = dev->private;
 	unsigned int trig = data[1];
 	unsigned int shift = data[3];
-	unsigned int hi_mask = data[4] << shift;
-	unsigned int lo_mask = data[5] << shift;
-	unsigned int chan_mask = hi_mask | lo_mask;
-	unsigned int old_mask = (1 << shift) - 1;
+	unsigned int hi_mask;
+	unsigned int lo_mask;
+	unsigned int chan_mask;
+	unsigned int old_mask;
 	unsigned int pm;
 	unsigned int pt;
 	unsigned int pp;
+	unsigned int invalid_chan;
 
 	if (trig > 1) {
 		dev_dbg(dev->class_dev,

@@ -475,7 +476,20 @@ static int apci1500_di_cfg_trig(struct c
 		return -EINVAL;
 	}
 
-	if (chan_mask > 0xffff) {
+	if (shift <= 16) {
+		hi_mask = data[4] << shift;
+		lo_mask = data[5] << shift;
+		old_mask = (1U << shift) - 1;
+		invalid_chan = (data[4] | data[5]) >> (16 - shift);
+	} else {
+		hi_mask = 0;
+		lo_mask = 0;
+		old_mask = 0xffff;
+		invalid_chan = data[4] | data[5];
+	}
+	chan_mask = hi_mask | lo_mask;
+
+	if (invalid_chan) {
 		dev_dbg(dev->class_dev, "invalid digital trigger channel\n");
 		return -EINVAL;
 	}

From: Ian Abbott <[email protected]>

commit 926234f1b8434c4409aa4c53637aa3362ca07cea upstream.

The INSN_CONFIG comedi instruction with sub-instruction code INSN_CONFIG_DIGITAL_TRIG includes a base channel in data[3]. This is used as a right shift amount for other bitmask values without being checked. Shift amounts greater than or equal to 32 will result in undefined behavior. Add code to deal with this.

---
 drivers/staging/comedi/drivers/addi_apci_1564.c |   20 ++++++++++++++------
 1 file changed, 14 insertions(+), 6 deletions(-)

@@ -340,14 +340,22 @@ static int apci1564_cos_insn_config(stru
 				    unsigned int *data)
 {
 	struct apci1564_private *devpriv = dev->private;
-	unsigned int shift, oldmask;
+	unsigned int shift, oldmask, himask, lomask;
 
 	switch (data[0]) {
 	case INSN_CONFIG_DIGITAL_TRIG:
 		if (data[1] != 0)
 			return -EINVAL;
 		shift = data[3];
-		oldmask = (1U << shift) - 1;
+		if (shift < 32) {
+			oldmask = (1U << shift) - 1;
+			himask = data[4] << shift;
+			lomask = data[5] << shift;
+		} else {
+			oldmask = 0xffffffffu;
+			himask = 0;
+			lomask = 0;
+		}
 		switch (data[2]) {
 		case COMEDI_DIGITAL_TRIG_DISABLE:
 			devpriv->ctrl = 0;

@@ -371,8 +379,8 @@ static int apci1564_cos_insn_config(stru
 				devpriv->mode2 &= oldmask;
 			}
 			/* configure specified channels */
-			devpriv->mode1 |= data[4] << shift;
-			devpriv->mode2 |= data[5] << shift;
+			devpriv->mode1 |= himask;
+			devpriv->mode2 |= lomask;
 			break;
 		case COMEDI_DIGITAL_TRIG_ENABLE_LEVELS:
 			if (devpriv->ctrl != (APCI1564_DI_IRQ_ENA |

@@ -389,8 +397,8 @@ static int apci1564_cos_insn_config(stru
 				devpriv->mode2 &= oldmask;
 			}
 			/* configure specified channels */
-			devpriv->mode1 |= data[4] << shift;
-			devpriv->mode2 |= data[5] << shift;
+			devpriv->mode1 |= himask;
+			devpriv->mode2 |= lomask;
 			break;
 		default:
 			return -EINVAL;

From: Yang Yingliang <[email protected]>

commit f4c23a140d80ef5e6d3d1f8f57007649014b60fa upstream.

I got null-ptr-deref in serial8250_start_tx():

[   78.114630] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[   78.123778] Mem abort info:
[   78.126560]   ESR = 0x86000007
[   78.129603]   EC = 0x21: IABT (current EL), IL = 32 bits
[   78.134891]   SET = 0, FnV = 0
[   78.137933]   EA = 0, S1PTW = 0
[   78.141064] user pgtable: 64k pages, 48-bit VAs, pgdp=00000027d41a8600
[   78.147562] [0000000000000000] pgd=00000027893f0003, p4d=00000027893f0003, pud=00000027893f0003, pmd=00000027c9a20003, pte=0000000000000000
[   78.160029] Internal error: Oops: 86000007 [#1] SMP
[   78.164886] Modules linked in: sunrpc vfat fat aes_ce_blk crypto_simd cryptd aes_ce_cipher crct10dif_ce ghash_ce sha2_ce sha256_arm64 sha1_ce ses enclosure sg sbsa_gwdt ipmi_ssif spi_dw_mmio sch_fq_codel vhost_net tun vhost vhost_iotlb tap ip_tables ext4 mbcache jbd2 ahci hisi_sas_v3_hw libahci hisi_sas_main libsas hns3 scsi_transport_sas hclge libata megaraid_sas ipmi_si hnae3 ipmi_devintf ipmi_msghandler br_netfilter bridge stp llc nvme nvme_core xt_sctp sctp libcrc32c dm_mod nbd
[   78.207383] CPU: 11 PID: 23258 Comm: null-ptr Not tainted 5.8.0-rc6+ #48
[   78.214056] Hardware name: Huawei TaiShan 2280 V2/BC82AMDC, BIOS 2280-V2 CS V3.B210.01 03/12/2020
[   78.222888] pstate: 80400089 (Nzcv daIf +PAN -UAO BTYPE=--)
[   78.228435] pc : 0x0
[   78.230618] lr : serial8250_start_tx+0x160/0x260
[   78.235215] sp : ffff800062eefb80
[   78.238517] x29: ffff800062eefb80 x28: 0000000000000fff
[   78.243807] x27: ffff800062eefd80 x26: ffff202fd83b3000
[   78.249098] x25: ffff800062eefd80 x24: ffff202fd83b3000
[   78.254388] x23: ffff002fc5e50be8 x22: 0000000000000002
[   78.259679] x21: 0000000000000001 x20: 0000000000000000
[   78.264969] x19: ffffa688827eecc8 x18: 0000000000000000
[   78.270259] x17: 0000000000000000 x16: 0000000000000000
[   78.275550] x15: ffffa68881bc67a8 x14: 00000000000002e6
[   78.280841] x13: ffffa68881bc67a8 x12: 000000000000c539
[   78.286131] x11: d37a6f4de9bd37a7 x10: ffffa68881cccff0
[   78.291421] x9 : ffffa68881bc6000 x8 : ffffa688819daa88
[   78.296711] x7 : ffffa688822a0f20 x6 : ffffa688819e0000
[   78.302002] x5 : ffff800062eef9d0 x4 : ffffa68881e707a8
[   78.307292] x3 : 0000000000000000 x2 : 0000000000000002
[   78.312582] x1 : 0000000000000001 x0 : ffffa688827eecc8
[   78.317873] Call trace:
[   78.320312]  0x0
[   78.322147]  __uart_start.isra.9+0x64/0x78
[   78.326229]  uart_start+0xb8/0x1c8
[   78.329620]  uart_flush_chars+0x24/0x30
[   78.333442]  n_tty_receive_buf_common+0x7b0/0xc30
[   78.338128]  n_tty_receive_buf+0x44/0x2c8
[   78.342122]  tty_ioctl+0x348/0x11f8
[   78.345599]  ksys_ioctl+0xd8/0xf8
[   78.348903]  __arm64_sys_ioctl+0x2c/0xc8
[   78.352812]  el0_svc_common.constprop.2+0x88/0x1b0
[   78.357583]  do_el0_svc+0x44/0xd0
[   78.360887]  el0_sync_handler+0x14c/0x1d0
[   78.364880]  el0_sync+0x140/0x180
[   78.368185] Code: bad PC value

SERIAL_PORT_DFNS is not defined on each arch, if it's not defined, serial8250_set_defaults() won't be called in serial8250_isa_init_ports(), so the p->serial_in pointer won't be initialized, and it leads a null-ptr-deref. Fix this problem by calling serial8250_set_defaults() after init uart port.

---
 drivers/tty/serial/8250/8250_core.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -534,6 +534,7 @@ static void __init serial8250_isa_init_p
 		 */
 		up->mcr_mask = ~ALPHA_KLUDGE_MCR;
 		up->mcr_force = ALPHA_KLUDGE_MCR;
+		serial8250_set_defaults(up);
 	}
 
 	/* chain base port ops to support Remote Supervisor Adapter */

@@ -557,7 +558,6 @@ static void __init serial8250_isa_init_p
 		port->membase  = old_serial_port[i].iomem_base;
 		port->iotype   = old_serial_port[i].io_type;
 		port->regshift = old_serial_port[i].iomem_reg_shift;
-		serial8250_set_defaults(up);
 
 		port->irqflags |= irqflag;
 		if (serial8250_isa_config != NULL)

From: Serge Semin <[email protected]>

commit 551e553f0d4ab623e2a6f424ab5834f9c7b5229c upstream.

Commit 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port") fixed limits of a baud rate setting for a generic 8250 port. In other words since that commit the baud rate has been permitted to be within [uartclk / 16 / UART_DIV_MAX; uartclk / 16], which is absolutely normal for a standard 8250 UART port. But there are custom 8250 ports, which provide extended baud rate limits. In particular the Mediatek 8250 port can work with baud rates up to "uartclk" speed.

Normally that and any other peculiarity is supposed to be handled in a custom set_termios() callback implemented in the vendor-specific 8250-port glue-driver. Currently that is how it's done for the most of the vendor-specific 8250 ports, but for some reason for Mediatek a solution has been spread out to both the glue-driver and to the generic 8250-port code. Due to that a bug has been introduced, which permitted the extended baud rate limit for all even for standard 8250-ports. The bug has been fixed by the commit 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port") by narrowing the baud rates limit back down to the normal bounds. Unfortunately by doing so we also broke the Mediatek-specific extended bauds feature.

A fix of the problem described above is twofold. First since we can't get back the extended baud rate limits feature to the generic set_termios() function and that method supports only a standard baud rates range, the requested baud rate must be locally stored before calling it and then restored back to the new termios structure after the generic set_termios() finished its magic business. By doing so we still use the serial8250_do_set_termios() method to set the LCR/MCR/FCR/etc. registers, while the extended baud rate setting procedure will be performed later in the custom Mediatek-specific set_termios() callback. Second since a true baud rate is now fully calculated in the custom set_termios() method we need to locally update the port timeout by calling the uart_update_timeout() function. After the fixes described above are implemented in the 8250_mtk.c driver, the Mediatek 8250-port should get back to normally working with extended baud rates.

---
 drivers/tty/serial/8250/8250_mtk.c |   18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

@@ -45,8 +45,21 @@ mtk8250_set_termios(struct uart_port *po
 	unsigned long flags;
 	unsigned int baud, quot;
 
+	/*
+	 * Store the requested baud rate before calling the generic 8250
+	 * set_termios method. Standard 8250 port expects bauds to be
+	 * no higher than (uartclk / 16) so the baud will be clamped if it
+	 * gets out of that bound. Mediatek 8250 port supports speed
+	 * higher than that, therefore we'll get original baud rate back
+	 * after calling the generic set_termios method and recalculate
+	 * the speed later in this method.
+	 */
+	baud = tty_termios_baud_rate(termios);
+
 	serial8250_do_set_termios(port, termios, old);
 
+	tty_termios_encode_baud_rate(termios, baud, baud);
+
 	/*
 	 * Mediatek UARTs use an extra highspeed register (UART_MTK_HIGHS)
 	 *

@@ -85,6 +98,11 @@ mtk8250_set_termios(struct uart_port *po
 	 */
 	spin_lock_irqsave(&port->lock, flags);
 
+	/*
+	 * Update the per-port timeout.
+	 */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
 	/* set DLAB we have cval saved in up->lcr from the call to the core */
 	serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB);
 	serial_dl_write(up, quot);

From: Tetsuo Handa <[email protected]>

commit 033724d6864245a11f8e04c066002e6ad22b3fd0 upstream.

syzbot is reporting general protection fault in bitfill_aligned() [1] caused by integer underflow in bit_clear_margins(). The cause of this problem is when and how do_vc_resize() updates vc->vc_{cols,rows}.

If vc_do_resize() fails (e.g. kzalloc() fails) when var.xres or var.yres is going to shrink, vc->vc_{cols,rows} will not be updated. This allows bit_clear_margins() to see info->var.xres < (vc->vc_cols * cw) or info->var.yres < (vc->vc_rows * ch). Unexpectedly large rw or bh will try to overrun the __iomem region and causes general protection fault.

Also, vc_resize(vc, 0, 0) does not set vc->vc_{cols,rows} = 0 due to

  new_cols = (cols ? cols : vc->vc_cols);
  new_rows = (lines ? lines : vc->vc_rows);

exception. Since cols and lines are calculated as

  cols = FBCON_SWAP(ops->rotate, info->var.xres, info->var.yres);
  rows = FBCON_SWAP(ops->rotate, info->var.yres, info->var.xres);
  cols /= vc->vc_font.width;
  rows /= vc->vc_font.height;
  vc_resize(vc, cols, rows);

in fbcon_modechanged(), var.xres < vc->vc_font.width makes cols = 0 and var.yres < vc->vc_font.height makes rows = 0. This means that

  const int fd = open("/dev/fb0", O_ACCMODE);
  struct fb_var_screeninfo var = { };
  ioctl(fd, FBIOGET_VSCREENINFO, &var);
  var.xres = var.yres = 1;
  ioctl(fd, FBIOPUT_VSCREENINFO, &var);

easily reproduces integer underflow bug explained above.

Of course, callers of vc_resize() are not handling vc_do_resize() failure is bad. But we can't avoid vc_resize(vc, 0, 0) which returns 0. Therefore, as a band-aid workaround, this patch checks integer underflow in "struct fbcon_ops"->clear_margins call, assuming that vc->vc_cols * vc->vc_font.width and vc->vc_rows * vc->vc_font.heigh do not cause integer overflow.

[1] https://syzkaller.appspot.com/bug?id=a565882df74fa76f10d3a6fec4be31098dbb37c6

---
 drivers/video/fbdev/core/bitblit.c   |    4 ++--
 drivers/video/fbdev/core/fbcon_ccw.c |    4 ++--
 drivers/video/fbdev/core/fbcon_cw.c  |    4 ++--
 drivers/video/fbdev/core/fbcon_ud.c  |    4 ++--
 4 files changed, 8 insertions(+), 8 deletions(-)

@@ -216,7 +216,7 @@ static void bit_clear_margins(struct vc_
 	region.color = color;
 	region.rop = ROP_COPY;
 
-	if (rw && !bottom_only) {
+	if ((int) rw > 0 && !bottom_only) {
 		region.dx = info->var.xoffset + rs;
 		region.dy = 0;
 		region.width = rw;

@@ -224,7 +224,7 @@ static void bit_clear_margins(struct vc_
 		info->fbops->fb_fillrect(info, &region);
 	}
 
-	if (bh) {
+	if ((int) bh > 0) {
 		region.dx = info->var.xoffset;
 		region.dy = info->var.yoffset + bs;
 		region.width = rs;

@@ -201,7 +201,7 @@ static void ccw_clear_margins(struct vc_
 	region.color = color;
 	region.rop = ROP_COPY;
 
-	if (rw && !bottom_only) {
+	if ((int) rw > 0 && !bottom_only) {
 		region.dx = 0;
 		region.dy = info->var.yoffset;
 		region.height = rw;

@@ -209,7 +209,7 @@ static void ccw_clear_margins(struct vc_
 		info->fbops->fb_fillrect(info, &region);
 	}
 
-	if (bh) {
+	if ((int) bh > 0) {
 		region.dx = info->var.xoffset + bs;
 		region.dy = 0;
                 region.height = info->var.yres_virtual;

@@ -184,7 +184,7 @@ static void cw_clear_margins(struct vc_d
 	region.color = color;
 	region.rop = ROP_COPY;
 
-	if (rw && !bottom_only) {
+	if ((int) rw > 0 && !bottom_only) {
 		region.dx = 0;
 		region.dy = info->var.yoffset + rs;
 		region.height = rw;

@@ -192,7 +192,7 @@ static void cw_clear_margins(struct vc_d
 		info->fbops->fb_fillrect(info, &region);
 	}
 
-	if (bh) {
+	if ((int) bh > 0) {
 		region.dx = info->var.xoffset;
 		region.dy = info->var.yoffset;
                 region.height = info->var.yres;

@@ -231,7 +231,7 @@ static void ud_clear_margins(struct vc_d
 	region.color = color;
 	region.rop = ROP_COPY;
 
-	if (rw && !bottom_only) {
+	if ((int) rw > 0 && !bottom_only) {
 		region.dy = 0;
 		region.dx = info->var.xoffset;
 		region.width  = rw;

@@ -239,7 +239,7 @@ static void ud_clear_margins(struct vc_d
 		info->fbops->fb_fillrect(info, &region);
 	}
 
-	if (bh) {
+	if ((int) bh > 0) {
 		region.dy = info->var.yoffset;
 		region.dx = info->var.xoffset;
                 region.height  = bh;

From: Tetsuo Handa <[email protected]>

commit ce684552a266cb1c7cc2f7e623f38567adec6653 upstream.

syzbot is reporting general protection fault in do_con_write() [1] caused by vc->vc_screenbuf == ZERO_SIZE_PTR caused by vc->vc_screenbuf_size == 0 caused by vc->vc_cols == vc->vc_rows == vc->vc_size_row == 0 caused by fb_set_var() from ioctl(FBIOPUT_VSCREENINFO) on /dev/fb0 , for gotoxy(vc, 0, 0) from reset_terminal() from vc_init() from vc_allocate()
from con_install() from tty_init_dev() from tty_open() on such console
causes vc->vc_pos == 0x10000000e due to
((unsigned long) ZERO_SIZE_PTR) + -1U * 0 + (-1U << 1).

I don't think that a console with 0 column or 0 row makes sense. And it seems that vc_do_resize() does not intend to allow resizing a console to 0 column or 0 row due to

  new_cols = (cols ? cols : vc->vc_cols);
  new_rows = (lines ? lines : vc->vc_rows);

exception.

Theoretically, cols and rows can be any range as long as 0 < cols * rows * 2 <= KMALLOC_MAX_SIZE is satisfied (e.g. cols == 1048576 && rows == 2 is possible) because of

  vc->vc_size_row = vc->vc_cols << 1;
  vc->vc_screenbuf_size = vc->vc_rows * vc->vc_size_row;

in visual_init() and kzalloc(vc->vc_screenbuf_size) in vc_allocate().

Since we can detect cols == 0 or rows == 0 via screenbuf_size = 0 in visual_init(), we can reject kzalloc(0). Then, vc_allocate() will return an error, and con_write() will not be called on a console with 0 column or 0 row.

We need to make sure that integer overflow in visual_init() won't happen. Since vc_do_resize() restricts cols <= 32767 and rows <= 32767, applying 1 <= cols <= 32767 and 1 <= rows <= 32767 restrictions to vc_allocate() will be practically fine.

This patch does not touch con_init(), for returning -EINVAL there does not help when we are not returning -ENOMEM.

[1] https://syzkaller.appspot.com/bug?extid=017265e8553724e514e8

---
 drivers/tty/vt/vt.c |   29 ++++++++++++++++++-----------
 1 file changed, 18 insertions(+), 11 deletions(-)

@@ -762,10 +762,19 @@ static const struct tty_port_operations
 	.destruct = vc_port_destruct,
 };
 
+/*
+ * Change # of rows and columns (0 means unchanged/the size of fg_console)
+ * [this is to be used together with some user program
+ * like resize that changes the hardware videomode]
+ */
+#define VC_MAXCOL (32767)
+#define VC_MAXROW (32767)
+
 int vc_allocate(unsigned int currcons)	/* return 0 on success */
 {
 	struct vt_notifier_param param;
 	struct vc_data *vc;
+	int err;
 
 	WARN_CONSOLE_UNLOCKED();
 

@@ -795,6 +804,11 @@ int vc_allocate(unsigned int currcons)	/
 	if (!*vc->vc_uni_pagedir_loc)
 		con_set_default_unimap(vc);
 
+	err = -EINVAL;
+	if (vc->vc_cols > VC_MAXCOL || vc->vc_rows > VC_MAXROW ||
+	    vc->vc_screenbuf_size > KMALLOC_MAX_SIZE || !vc->vc_screenbuf_size)
+		goto err_free;
+	err = -ENOMEM;
 	vc->vc_screenbuf = kzalloc(vc->vc_screenbuf_size, GFP_KERNEL);
 	if (!vc->vc_screenbuf)
 		goto err_free;

@@ -812,7 +826,7 @@ int vc_allocate(unsigned int currcons)	/
 err_free:
 	kfree(vc);
 	vc_cons[currcons].d = NULL;
-	return -ENOMEM;
+	return err;
 }
 
 static inline int resize_screen(struct vc_data *vc, int width, int height,

@@ -827,14 +841,6 @@ static inline int resize_screen(struct v
 	return err;
 }
 
-/*
- * Change # of rows and columns (0 means unchanged/the size of fg_console)
- * [this is to be used together with some user program
- * like resize that changes the hardware videomode]
- */
-#define VC_RESIZE_MAXCOL (32767)
-#define VC_RESIZE_MAXROW (32767)
-
 /**
  *	vc_do_resize	-	resizing method for the tty
  *	@tty: tty being resized

@@ -869,7 +875,7 @@ static int vc_do_resize(struct tty_struc
 	user = vc->vc_resize_user;
 	vc->vc_resize_user = 0;
 
-	if (cols > VC_RESIZE_MAXCOL || lines > VC_RESIZE_MAXROW)
+	if (cols > VC_MAXCOL || lines > VC_MAXROW)
 		return -EINVAL;
 
 	new_cols = (cols ? cols : vc->vc_cols);

@@ -880,7 +886,7 @@ static int vc_do_resize(struct tty_struc
 	if (new_cols == vc->vc_cols && new_rows == vc->vc_rows)
 		return 0;
 
-	if (new_screen_size > KMALLOC_MAX_SIZE)
+	if (new_screen_size > KMALLOC_MAX_SIZE || !new_screen_size)
 		return -EINVAL;
 	newscreen = kzalloc(new_screen_size, GFP_USER);
 	if (!newscreen)

@@ -3031,6 +3037,7 @@ static int __init con_init(void)
 		INIT_WORK(&vc_cons[currcons].SAK_work, vc_SAK);
 		tty_port_init(&vc->port);
 		visual_init(vc, currcons, 1);
+		/* Assuming vc->vc_{cols,rows,screenbuf_size} are sane here. */
 		vc->vc_screenbuf = kzalloc(vc->vc_screenbuf_size, GFP_NOWAIT);
 		vc_init(vc, vc->vc_rows, vc->vc_cols,
 			currcons || !vc->vc_sw->con_save_screen);

From: Fangrui Song <[email protected]>

commit ca9b31f6bb9c6aa9b4e5f0792f39a97bbffb8c51 upstream.

When CROSS_COMPILE is set (e.g. aarch64-linux-gnu-), if $(CROSS_COMPILE)elfedit is found at /usr/bin/aarch64-linux-gnu-elfedit, GCC_TOOLCHAIN_DIR will be set to /usr/bin/. --prefix= will be set to /usr/bin/ and Clang as of 11 will search for both $(prefix)aarch64-linux-gnu-$needle and $(prefix)$needle.

GCC searchs for $(prefix)aarch64-linux-gnu/$version/$needle, $(prefix)aarch64-linux-gnu/$needle and $(prefix)$needle. In practice, $(prefix)aarch64-linux-gnu/$needle rarely contains executables.

To better model how GCC's -B/--prefix takes in effect in practice, newer Clang (since
https://github.com/llvm/llvm-project/commit/3452a0d8c17f7166f479706b293caf6ac76ffd90)
only searches for $(prefix)$needle. Currently it will find /usr/bin/as instead of /usr/bin/aarch64-linux-gnu-as.

Set --prefix= to $(GCC_TOOLCHAIN_DIR)$(notdir $(CROSS_COMPILE)) (/usr/bin/aarch64-linux-gnu-) so that newer Clang can find the appropriate cross compiling GNU as (when -no-integrated-as is in effect).

---
 Makefile |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -482,7 +482,7 @@ ifeq ($(cc-name),clang)
 ifneq ($(CROSS_COMPILE),)
 CLANG_FLAGS	+= --target=$(notdir $(CROSS_COMPILE:%-=%))
 GCC_TOOLCHAIN_DIR := $(dir $(shell which $(CROSS_COMPILE)elfedit))
-CLANG_FLAGS	+= --prefix=$(GCC_TOOLCHAIN_DIR)
+CLANG_FLAGS	+= --prefix=$(GCC_TOOLCHAIN_DIR)$(notdir $(CROSS_COMPILE))
 GCC_TOOLCHAIN	:= $(realpath $(GCC_TOOLCHAIN_DIR)/..)
 endif
 ifneq ($(GCC_TOOLCHAIN),)

From: Hugh Dickins <[email protected]>

commit 8d22a9351035ef2ff12ef163a1091b8b8cf1e49c upstream.

It was hard to keep a test running, moving tasks between memcgs with move_charge_at_immigrate, while swapping: mem_cgroup_id_get_many()'s refcount is discovered to be 0 (supposedly impossible), so it is then forced to REFCOUNT_SATURATED, and after thousands of warnings in quick succession, the test is at last put out of misery by being OOM killed.

This is because of the way moved_swap accounting was saved up until the task move gets completed in __mem_cgroup_clear_mc(), deferred from when mem_cgroup_move_swap_account() actually exchanged old and new ids. Concurrent activity can free up swap quicker than the task is scanned, bringing id refcount down 0 (which should only be possible when offlining).

Just skip that optimization: do that part of the accounting immediately.

---
 mm/memcontrol.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

@@ -4883,7 +4883,6 @@ static void __mem_cgroup_clear_mc(void)
 		if (!mem_cgroup_is_root(mc.to))
 			page_counter_uncharge(&mc.to->memory, mc.moved_swap);
 
-		mem_cgroup_id_get_many(mc.to, mc.moved_swap);
 		css_put_many(&mc.to->css, mc.moved_swap);
 
 		mc.moved_swap = 0;

@@ -5074,7 +5073,8 @@ put:			/* get_mctgt_type() gets the page
 			ent = target.ent;
 			if (!mem_cgroup_move_swap_account(ent, mc.from, mc.to)) {
 				mc.precharge--;
-				/* we fixup refcnts and charges later. */
+				mem_cgroup_id_get_many(mc.to, 1);
+				/* we fixup other refcnts and charges later. */
 				mc.moved_swap++;
 			}
 			break;

From: Michael J. Ruhl <[email protected]>

commit e0b3e0b1a04367fc15c07f44e78361545b55357c upstream.

The !ATOMIC_IOMAP version of io_maping_init_wc will always return success, even when the ioremap fails.

Since the ATOMIC_IOMAP version returns NULL when the init fails, and callers check for a NULL return on error this is unexpected.

During a device probe, where the ioremap failed, a crash can look like this:

    BUG: unable to handle page fault for address: 0000000000210000
     #PF: supervisor write access in kernel mode
     #PF: error_code(0x0002) - not-present page
     Oops: 0002 [#1] PREEMPT SMP
     CPU: 0 PID: 177 Comm:
     RIP: 0010:fill_page_dma [i915]
       gen8_ppgtt_create [i915]
       i915_ppgtt_create [i915]
       intel_gt_init [i915]
       i915_gem_init [i915]
       i915_driver_probe [i915]
       pci_device_probe
       really_probe
       driver_probe_device

The remap failure occurred much earlier in the probe. If it had been propagated, the driver would have exited with an error.

Return NULL on ioremap failure.

[[email protected]: detect ioremap_wc() errors earlier]

---
 include/linux/io-mapping.h |    5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

@@ -120,9 +120,12 @@ io_mapping_init_wc(struct io_mapping *io
 		   resource_size_t base,
 		   unsigned long size)
 {
+	iomap->iomem = ioremap_wc(base, size);
+	if (!iomap->iomem)
+		return NULL;
+
 	iomap->base = base;
 	iomap->size = size;
-	iomap->iomem = ioremap_wc(base, size);
 #if defined(pgprot_noncached_wc) /* archs can't agree on a name ... */
 	iomap->prot = pgprot_noncached_wc(PAGE_KERNEL);
 #elif defined(pgprot_writecombine)

From: John David Anglin <[email protected]>

commit be6577af0cef934ccb036445314072e8cb9217b9 upstream.

Stalls are quite frequent with recent kernels. I enabled CONFIG_SOFTLOCKUP_DETECTOR and I caught the following stall:

watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [cc1:22803]
CPU: 0 PID: 22803 Comm: cc1 Not tainted 5.6.17+ #3
Hardware name: 9000/800/rp3440
 IAOQ[0]: d_alloc_parallel+0x384/0x688
 IAOQ[1]: d_alloc_parallel+0x388/0x688
 RP(r2): d_alloc_parallel+0x134/0x688
Backtrace:
 [<000000004036974c>] __lookup_slow+0xa4/0x200
 [<0000000040369fc8>] walk_component+0x288/0x458
 [<000000004036a9a0>] path_lookupat+0x88/0x198
 [<000000004036e748>] filename_lookup+0xa0/0x168
 [<000000004036e95c>] user_path_at_empty+0x64/0x80
 [<000000004035d93c>] vfs_statx+0x104/0x158
 [<000000004035dfcc>] __do_sys_lstat64+0x44/0x80
 [<000000004035e5a0>] sys_lstat64+0x20/0x38
 [<0000000040180054>] syscall_exit+0x0/0x14

The code was stuck in this loop in d_alloc_parallel:

    4037d414:   0e 00 10 dc     ldd 0(r16),ret0
    4037d418:   c7 fc 5f ed     bb,< ret0,1f,4037d414 <d_alloc_parallel+0x384>
    4037d41c:   08 00 02 40     nop

This is the inner loop of bit_spin_lock which is called by hlist_bl_unlock in d_alloc_parallel:

static inline void bit_spin_lock(int bitnum, unsigned long *addr) {
/*
* Assuming the lock is uncontended, this never enters
* the body of the outer loop. If it is contended, then
* within the inner loop a non-atomic test is used to
* busywait with less bus contention for a good time to
* attempt to acquire the lock bit.
*/
preempt_disable();

#if defined(CONFIG_SMP) || defined(CONFIG_DEBUG_SPINLOCK)
        while (unlikely(test_and_set_bit_lock(bitnum, addr))) {
                preempt_enable();
                do {
                        cpu_relax();
                } while (test_bit(bitnum, addr));
                preempt_disable();
        }
#endif
        __acquire(bitlock);
}

After consideration, I realized that we must be losing bit unlocks. Then, I noticed that we missed defining atomic64_set_release(). Adding this define fixes the stalls in bit operations.

---
 arch/parisc/include/asm/atomic.h |    2 ++
 1 file changed, 2 insertions(+)

@@ -258,6 +258,8 @@ atomic64_set(atomic64_t *v, s64 i)
 	_atomic_spin_unlock_irqrestore(v, flags);
 }
 
+#define atomic64_set_release(v, i)	atomic64_set((v), (i))
+
 static __inline__ s64
 atomic64_read(const atomic64_t *v)
 {

From: Qiujun Huang <[email protected]>

commit 2bbcaaee1fcbd83272e29f31e2bb7e70d8c49e05 upstream.

In ath9k_hif_usb_rx_cb interface number is assumed to be 0. usb_ifnum_to_if(urb->dev, 0)
But it isn't always true.

The case reported by syzbot:
https://lore.kernel.org/linux-usb/[email protected]
usb 2-1: new high-speed USB device number 2 using dummy_hcd usb 2-1: config 1 has an invalid interface number: 2 but max is 0 usb 2-1: config 1 has no interface number 0
usb 2-1: New USB device found, idVendor=0cf3, idProduct=9271, bcdDevice= 1.08
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3

general protection fault, probably for non-canonical address
0xdffffc0000000015: 0000 [#1] SMP KASAN
KASAN: null-ptr-deref in range [0x00000000000000a8-0x00000000000000af]
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.0-rc5-syzkaller #0

Call Trace

__usb_hcd_giveback_urb+0x29a/0x550 drivers/usb/core/hcd.c:1650
usb_hcd_giveback_urb+0x368/0x420 drivers/usb/core/hcd.c:1716
dummy_timer+0x1258/0x32ae drivers/usb/gadget/udc/dummy_hcd.c:1966
call_timer_fn+0x195/0x6f0 kernel/time/timer.c:1404
expire_timers kernel/time/timer.c:1449 [inline]
__run_timers kernel/time/timer.c:1773 [inline]
__run_timers kernel/time/timer.c:1740 [inline]
run_timer_softirq+0x5f9/0x1500 kernel/time/timer.c:1786
__do_softirq+0x21e/0x950 kernel/softirq.c:292
invoke_softirq kernel/softirq.c:373 [inline]
irq_exit+0x178/0x1a0 kernel/softirq.c:413
exiting_irq arch/x86/include/asm/apic.h:546 [inline]
smp_apic_timer_interrupt+0x141/0x540 arch/x86/kernel/apic/apic.c:1146
apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:829

---
 drivers/net/wireless/ath/ath9k/hif_usb.c |   48 +++++++++++++++++++++++--------
 drivers/net/wireless/ath/ath9k/hif_usb.h |    5 +++
 2 files changed, 42 insertions(+), 11 deletions(-)

@@ -641,9 +641,9 @@ err:
 
 static void ath9k_hif_usb_rx_cb(struct urb *urb)
 {
-	struct sk_buff *skb = (struct sk_buff *) urb->context;
-	struct hif_device_usb *hif_dev =
-		usb_get_intfdata(usb_ifnum_to_if(urb->dev, 0));
+	struct rx_buf *rx_buf = (struct rx_buf *)urb->context;
+	struct hif_device_usb *hif_dev = rx_buf->hif_dev;
+	struct sk_buff *skb = rx_buf->skb;
 	int ret;
 
 	if (!skb)

@@ -683,14 +683,15 @@ resubmit:
 	return;
 free:
 	kfree_skb(skb);
+	kfree(rx_buf);
 }
 
 static void ath9k_hif_usb_reg_in_cb(struct urb *urb)
 {
-	struct sk_buff *skb = (struct sk_buff *) urb->context;
+	struct rx_buf *rx_buf = (struct rx_buf *)urb->context;
+	struct hif_device_usb *hif_dev = rx_buf->hif_dev;
+	struct sk_buff *skb = rx_buf->skb;
 	struct sk_buff *nskb;
-	struct hif_device_usb *hif_dev =
-		usb_get_intfdata(usb_ifnum_to_if(urb->dev, 0));
 	int ret;
 
 	if (!skb)

@@ -748,6 +749,7 @@ resubmit:
 	return;
 free:
 	kfree_skb(skb);
+	kfree(rx_buf);
 	urb->context = NULL;
 }
 

@@ -793,7 +795,7 @@ static int ath9k_hif_usb_alloc_tx_urbs(s
 	init_usb_anchor(&hif_dev->mgmt_submitted);
 
 	for (i = 0; i < MAX_TX_URB_NUM; i++) {
-		tx_buf = kzalloc(sizeof(struct tx_buf), GFP_KERNEL);
+		tx_buf = kzalloc(sizeof(*tx_buf), GFP_KERNEL);
 		if (!tx_buf)
 			goto err;
 

@@ -830,8 +832,9 @@ static void ath9k_hif_usb_dealloc_rx_urb
 
 static int ath9k_hif_usb_alloc_rx_urbs(struct hif_device_usb *hif_dev)
 {
-	struct urb *urb = NULL;
+	struct rx_buf *rx_buf = NULL;
 	struct sk_buff *skb = NULL;
+	struct urb *urb = NULL;
 	int i, ret;
 
 	init_usb_anchor(&hif_dev->rx_submitted);

@@ -839,6 +842,12 @@ static int ath9k_hif_usb_alloc_rx_urbs(s
 
 	for (i = 0; i < MAX_RX_URB_NUM; i++) {
 
+		rx_buf = kzalloc(sizeof(*rx_buf), GFP_KERNEL);
+		if (!rx_buf) {
+			ret = -ENOMEM;
+			goto err_rxb;
+		}
+
 		/* Allocate URB */
 		urb = usb_alloc_urb(0, GFP_KERNEL);
 		if (urb == NULL) {

@@ -853,11 +862,14 @@ static int ath9k_hif_usb_alloc_rx_urbs(s
 			goto err_skb;
 		}
 
+		rx_buf->hif_dev = hif_dev;
+		rx_buf->skb = skb;
+
 		usb_fill_bulk_urb(urb, hif_dev->udev,
 				  usb_rcvbulkpipe(hif_dev->udev,
 						  USB_WLAN_RX_PIPE),
 				  skb->data, MAX_RX_BUF_SIZE,
-				  ath9k_hif_usb_rx_cb, skb);
+				  ath9k_hif_usb_rx_cb, rx_buf);
 
 		/* Anchor URB */
 		usb_anchor_urb(urb, &hif_dev->rx_submitted);

@@ -883,6 +895,8 @@ err_submit:
 err_skb:
 	usb_free_urb(urb);
 err_urb:
+	kfree(rx_buf);
+err_rxb:
 	ath9k_hif_usb_dealloc_rx_urbs(hif_dev);
 	return ret;
 }

@@ -894,14 +908,21 @@ static void ath9k_hif_usb_dealloc_reg_in
 
 static int ath9k_hif_usb_alloc_reg_in_urbs(struct hif_device_usb *hif_dev)
 {
-	struct urb *urb = NULL;
+	struct rx_buf *rx_buf = NULL;
 	struct sk_buff *skb = NULL;
+	struct urb *urb = NULL;
 	int i, ret;
 
 	init_usb_anchor(&hif_dev->reg_in_submitted);
 
 	for (i = 0; i < MAX_REG_IN_URB_NUM; i++) {
 
+		rx_buf = kzalloc(sizeof(*rx_buf), GFP_KERNEL);
+		if (!rx_buf) {
+			ret = -ENOMEM;
+			goto err_rxb;
+		}
+
 		/* Allocate URB */
 		urb = usb_alloc_urb(0, GFP_KERNEL);
 		if (urb == NULL) {

@@ -916,11 +937,14 @@ static int ath9k_hif_usb_alloc_reg_in_ur
 			goto err_skb;
 		}
 
+		rx_buf->hif_dev = hif_dev;
+		rx_buf->skb = skb;
+
 		usb_fill_int_urb(urb, hif_dev->udev,
 				  usb_rcvintpipe(hif_dev->udev,
 						  USB_REG_IN_PIPE),
 				  skb->data, MAX_REG_IN_BUF_SIZE,
-				  ath9k_hif_usb_reg_in_cb, skb, 1);
+				  ath9k_hif_usb_reg_in_cb, rx_buf, 1);
 
 		/* Anchor URB */
 		usb_anchor_urb(urb, &hif_dev->reg_in_submitted);

@@ -946,6 +970,8 @@ err_submit:
 err_skb:
 	usb_free_urb(urb);
 err_urb:
+	kfree(rx_buf);
+err_rxb:
 	ath9k_hif_usb_dealloc_reg_in_urbs(hif_dev);
 	return ret;
 }

@@ -86,6 +86,11 @@ struct tx_buf {
 	struct list_head list;
 };
 
+struct rx_buf {
+	struct sk_buff *skb;
+	struct hif_device_usb *hif_dev;
+};
+
 #define HIF_USB_TX_STOP  BIT(0)
 #define HIF_USB_TX_FLUSH BIT(1)
 

From: Mark O'Donovan <[email protected]>

commit 92f53e2fda8bb9a559ad61d57bfb397ce67ed0ab upstream.

This fix allows ath9k_htc modules to connect to WLAN once again.

---
 drivers/net/wireless/ath/ath9k/hif_usb.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

@@ -731,11 +731,13 @@ static void ath9k_hif_usb_reg_in_cb(stru
 			return;
 		}
 
+		rx_buf->skb = nskb;
+
 		usb_fill_int_urb(urb, hif_dev->udev,
 				 usb_rcvintpipe(hif_dev->udev,
 						 USB_REG_IN_PIPE),
 				 nskb->data, MAX_REG_IN_BUF_SIZE,
-				 ath9k_hif_usb_reg_in_cb, nskb, 1);
+				 ath9k_hif_usb_reg_in_cb, rx_buf, 1);
 	}
 
 resubmit: