Enable mt7531 switch support for MT7629
Subsystems (3)
v2 cover Enable mt7531 switch support for MT7629
This patch series enable MT7629 sgmii mode with mt7531 switch support,
1. enable mt7629 sgmii mode support in mediatek eth driver
2. enable mt7629 ethernet dts node with sgmii mode and mt7531 switch support
Change since V1:
- use driver private data from dts to decide the register offset (SGMSYS_GEN2_SPEED) instead of check #ifdefs in drivers.
MarkLee (2):
eth: mtk-eth: enable mt7629 sgmii mode support in mediatek eth driver
arm: dts: mediatek: enable sgmii mode and mt7531 switch for mt7629
arch/arm/dts/mt7629-rfb.dts | 12 +++++++----- drivers/net/mtk_eth.c | 3 ++- drivers/net/mtk_eth.h | 1 + 3 files changed, 10 insertions(+), 6 deletions(-)
Signature · 1 line
2.17.1
PATCH RESEND v2 1/2 eth: mtk-eth: enable mt7629 sgmii mode support in mediatek eth driver
The sgmii mode init flow is almost the same for all mediatek SoC, the only difference is the register offset(SGMSYS_GEN2_SPEED) is 0x2028 in the old chip(mt7622) but changed to 0x128 for the newer chip(mt7629 and the following chips).
---
V2: use driver private data from dts to decide the register offset
(SGMSYS_GEN2_SPEED) instead of check #ifdefs in drivers.
--- drivers/net/mtk_eth.c | 3 ++- drivers/net/mtk_eth.h | 1 + 2 files changed, 3 insertions(+), 1 deletion(-)
drivers/net/mtk_eth.c +2 -1
@@ -1090,7 +1090,8 @@ static int mtk_phy_probe(struct udevice *dev)static void mtk_sgmii_init (struct mtk_eth_priv *priv) {/* Set SGMII GEN2 speed(2.5G) */ -clrsetbits_le32 (priv->sgmii_base +SGMSYS_GEN2_SPEED , +clrsetbits_le32 (priv->sgmii_base + ((priv->soc ==SOC_MT7622 ) ? +SGMSYS_GEN2_SPEED :SGMSYS_GEN2_SPEED_V2 ),SGMSYS_SPEED_2500 ,SGMSYS_SPEED_2500 );/* Disable SGMII AN */
drivers/net/mtk_eth.h +1 -0
@@ -45,6 +45,7 @@#define SGMII_PHYA_PWD BIT(4)#define SGMSYS_GEN2_SPEED 0x2028 +#define SGMSYS_GEN2_SPEED_V2 0x128#define SGMSYS_SPEED_2500 BIT(2)/* Frame Engine Registers */
Signature · 1 line
2.17.1
PATCH RESEND v2 2/2 arm: dts: mediatek: enable sgmii mode and mt7531 switch for mt7629
In reply to MarkLeeThis patch enable sgmii mode and mt7531 switch support in mt7629 ethernet dts node
---
V2: no changes
--- arch/arm/dts/mt7629-rfb.dts | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-)
arch/arm/dts/mt7629-rfb.dts +7 -5
@@ -24,12 +24,14 @@ ð { status = "okay"; - mediatek,gmac-id = <1>; - phy-mode = "gmii"; - phy-handle = <&phy0>; + mediatek,gmac-id = <0>; + phy-mode = "sgmii"; + mediatek,switch = "mt7531"; + reset-gpios = <&gpio 28 GPIO_ACTIVE_HIGH>; - phy0: ethernet-phy at 0 { - reg = <0>; + fixed-link { + speed = <1000>; + full-duplex; }; };
Signature · 1 line
2.17.1