Skip to contentSkip to conversation

ARM: dts: stm32: Move ethernet PHY into SoM DT

PATCH In review Marek Vasut 2 participants 3 messages Jul 29, 2020 – Aug 28, 2020

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/2 ARM: dts: stm32: Move ethernet PHY into SoM DT

The PHY and the VIO regulator is populated on the SoM, move it into the SoM DT.

Cc Alexandre Torgue <[email protected]>
Cc Maxime Coquelin <[email protected]>
Cc Patrice Chotard <[email protected]>
Cc Patrick Delaunay <[email protected]>

To: [email protected]
---
V2: No change

---
 arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi | 33 -----------------
 arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi  | 36 +++++++++++++++++++
 2 files changed, 36 insertions(+), 33 deletions(-)
arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi +0 -33
index 7c4bd615b311..9cf6d90fbf69 100644
@@ -11,7 +11,6 @@ aliases {
 		serial0 = &uart4;
 		serial1 = &usart3;
 		serial2 = &uart8;
-		ethernet0 = &ethernet0;
 	};
 
 	chosen {
@@ -33,16 +32,6 @@ display_bl: display-bl {
 		status = "okay";
 	};
 
-	ethernet_vio: vioregulator {
-		compatible = "regulator-fixed";
-		regulator-name = "vio";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
-		regulator-always-on;
-		regulator-boot-on;
-	};
-
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
 		#size-cells = <0>;
@@ -141,28 +130,6 @@ &cec {
 	status = "okay";
 };
 
-&ethernet0 {
-	status = "okay";
-	pinctrl-0 = <&ethernet0_rmii_pins_a>;
-	pinctrl-1 = <&ethernet0_rmii_sleep_pins_a>;
-	pinctrl-names = "default", "sleep";
-	phy-mode = "rmii";
-	max-speed = <100>;
-	phy-handle = <&phy0>;
-	st,eth-ref-clk-sel;
-	phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
-
-	mdio0 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "snps,dwmac-mdio";
-
-		phy0: ethernet-phy@1 {
-			reg = <1>;
-		};
-	};
-};
-
 &i2c2 {	/* Header X22 */
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c2_pins_a>;
arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi +36 -0
index ba905196fb54..d30a3c60da9b 100644
@@ -9,6 +9,10 @@
 #include <dt-bindings/mfd/st,stpmic1.h>
 
 / {
+	aliases {
+		ethernet0 = &ethernet0;
+	};
+
 	memory@c0000000 {
 		device_type = "memory";
 		reg = <0xC0000000 0x40000000>;
@@ -55,6 +59,16 @@ retram: retram@38000000 {
 			no-map;
 		};
 	};
+
+	ethernet_vio: vioregulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
 };
 
 &adc {
@@ -94,6 +108,28 @@ &dts {
 	status = "okay";
 };
 
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	max-speed = <100>;
+	phy-handle = <&phy0>;
+	st,eth-ref-clk-sel;
+	phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy@1 {
+			reg = <1>;
+		};
+	};
+};
+
 &i2c4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c4_pins_a>;
Signature · 7 lines
2.27.0


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#1 lore raw

PATCH v2 2/2 ARM: dts: stm32: Add DHSOM based DRC02 board

Add DT for DH DRC02 unit, which is a universal controller device. The system has two ethernet ports, two CANs, RS485 and RS232, USB, capacitive buttons and an OLED display.

Cc Alexandre Torgue <[email protected]>
Cc Maxime Coquelin <[email protected]>
Cc Patrice Chotard <[email protected]>
Cc Patrick Delaunay <[email protected]>

To: [email protected]
---
V2: - Invert the RS485 RE/DE polarity
- Write electronics with lowercase e

---
 arch/arm/boot/dts/Makefile                    |   1 +
 arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dts |  35 ++++
 arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts  |   4 +-
 .../arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi | 157 ++++++++++++++++++
 4 files changed, 195 insertions(+), 2 deletions(-)
 create mode 100644 arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dts
 create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi
arch/arm/boot/dts/Makefile +1 -0
index 4572db3fa5ae..8cdcf7316ca2 100644
@@ -1047,6 +1047,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
 	stm32746g-eval.dtb \
 	stm32h743i-eval.dtb \
 	stm32h743i-disco.dtb \
+	stm32mp153c-dhcom-drc02.dtb \
 	stm32mp157a-avenger96.dtb \
 	stm32mp157a-dhcor-avenger96.dtb \
 	stm32mp157a-dk1.dtb \
arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dts new file +35 -0
new file mode 100644
index 000000000000..02a39132958e
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
+ *
+ * DHCOM STM32MP1 variant:
+ * DHCM-STM32MP153C-C065-R102-F0819-SPI-E2-CAN2-RTC-I-01D2
+ * DHCOM PCB number: 587-200 or newer
+ * DRC02 PCB number: 568-100 or newer
+ */
+/dts-v1/;
+
+#include "stm32mp153.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-drc02.dtsi"
+
+/ {
+	model = "DH electronics STM32MP153C DHCOM DRC02";
+	compatible = "dh,stm32mp153c-dhcom-drc02", "dh,stm32mp153c-dhcom-som",
+		     "st,stm32mp153";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_a>;
+	pinctrl-1 = <&m_can1_sleep_pins_a>;
+	status = "okay";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "okay";
+};
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts +2 -2
index 197aa98d49e2..d3b81382f97c 100644
@@ -4,7 +4,7 @@
  *
  * DHCOM STM32MP1 variant:
  * DHCM-STM32MP157C-C065-R102-F0819-SPI-E2-CAN2-SDR104-RTC-WBT-T-DSI-I-01D2
- * DHCOR PCB number: 587-200 or newer
+ * DHCOM PCB number: 587-200 or newer
  * PDK2 PCB number: 516-400 or newer
  */
 /dts-v1/;
@@ -15,7 +15,7 @@
 #include "stm32mp15xx-dhcom-pdk2.dtsi"
 
 / {
-	model = "DH Electronics STM32MP157C DHCOM Premium Developer Kit (2)";
+	model = "DH electronics STM32MP157C DHCOM Premium Developer Kit (2)";
 	compatible = "dh,stm32mp157c-dhcom-pdk2", "dh,stm32mp157c-dhcom-som",
 		     "st,stm32mp157";
 };
arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi new file +157 -0

157 lines not on this page · raw message

Signature · 7 lines
2.27.0


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#2 lore raw

Re: [PATCH V2 2/2] ARM: dts: stm32: Add DHSOM based DRC02 board

Hi Marek

Quoted 14 lines · Marek Vasut

Add DT for DH DRC02 unit, which is a universal controller device. The system has two ethernet ports, two CANs, RS485 and RS232, USB, capacitive buttons and an OLED display.

Cc Alexandre Torgue <[email protected]>
Cc Maxime Coquelin <[email protected]>
Cc Patrice Chotard <[email protected]>
Cc Patrick Delaunay <[email protected]>

To: [email protected]
---
V2: - Invert the RS485 RE/DE polarity
- Write electronics with lowercase e

Quoted 9 lines
---
  arch/arm/boot/dts/Makefile                    |   1 +
  arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dts |  35 ++++
  arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts  |   4 +-
  .../arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi | 157 ++++++++++++++++++
  4 files changed, 195 insertions(+), 2 deletions(-)

create mode 100644 arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dts create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi

Series applied on stm32-next.

Regards
Alex

Quoted 229 lines
arch/arm/boot/dts/Makefile +1 -0
index 4572db3fa5ae..8cdcf7316ca2 100644
@@ -1047,6 +1047,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
  	stm32746g-eval.dtb \
  	stm32h743i-eval.dtb \
  	stm32h743i-disco.dtb \
+	stm32mp153c-dhcom-drc02.dtb \
  	stm32mp157a-avenger96.dtb \
  	stm32mp157a-dhcor-avenger96.dtb \
  	stm32mp157a-dk1.dtb \
arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dts new file +35 -0
new file mode 100644
index 000000000000..02a39132958e
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
+ *
+ * DHCOM STM32MP1 variant:
+ * DHCM-STM32MP153C-C065-R102-F0819-SPI-E2-CAN2-RTC-I-01D2
+ * DHCOM PCB number: 587-200 or newer
+ * DRC02 PCB number: 568-100 or newer
+ */
+/dts-v1/;
+
+#include "stm32mp153.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-drc02.dtsi"
+
+/ {
+	model = "DH electronics STM32MP153C DHCOM DRC02";
+	compatible = "dh,stm32mp153c-dhcom-drc02", "dh,stm32mp153c-dhcom-som",
+		     "st,stm32mp153";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_a>;
+	pinctrl-1 = <&m_can1_sleep_pins_a>;
+	status = "okay";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "okay";
+};
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts +2 -2
index 197aa98d49e2..d3b81382f97c 100644
@@ -4,7 +4,7 @@
   *
   * DHCOM STM32MP1 variant:
   * DHCM-STM32MP157C-C065-R102-F0819-SPI-E2-CAN2-SDR104-RTC-WBT-T-DSI-I-01D2
- * DHCOR PCB number: 587-200 or newer
+ * DHCOM PCB number: 587-200 or newer
   * PDK2 PCB number: 516-400 or newer
   */
  /dts-v1/;
@@ -15,7 +15,7 @@
  #include "stm32mp15xx-dhcom-pdk2.dtsi"
 
  / {
-	model = "DH Electronics STM32MP157C DHCOM Premium Developer Kit (2)";
+	model = "DH electronics STM32MP157C DHCOM Premium Developer Kit (2)";
  	compatible = "dh,stm32mp157c-dhcom-pdk2", "dh,stm32mp157c-dhcom-som",
  		     "st,stm32mp157";
  };
arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi new file +147 -0
new file mode 100644
index 000000000000..62ab23824a3e
@@ -0,0 +1,157 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&adc {
+	status = "disabled";
+};
+
+&dac {
+	status = "disabled";
+};
+
+&gpiob {
+	/*
+	 * NOTE: On DRC02, the RS485_RX_En is controlled by a separate
+	 * GPIO line, however the STM32 UART driver assumes RX happens
+	 * during TX anyway and that it only controls drive enable DE
+	 * line. Hence, the RX is always enabled here.
+	 */
+	rs485-rx-en {
+		gpio-hog;
+		gpios = <8 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "rs485-rx-en";
+	};
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "Out1",
+			  "Out2", "", "", "";
+};
+
+&gpioi {
+	gpio-line-names = "In1", "", "", "",
+			  "", "", "", "",
+			  "In2", "", "", "",
+			  "", "", "", "";
+
+	/*
+	 * NOTE: The USB Hub on the DRC02 needs a reset signal to be
+	 * pulled high in order to be detected by the USB Controller.
+	 * This signal should be handled by USB power sequencing in
+	 * order to reset the Hub when USB bus is powered down, but
+	 * so far there is no such functionality.
+	 */
+	usb-hub {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "usb-hub-reset";
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c04";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&i2c5 {	/* TP7/TP8 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&sdmmc3 {
+	/*
+	 * On DRC02, the SoM does not have SDIO WiFi. The pins
+	 * are used for on-board microSD slot instead.
+	 */
+	/delete-property/broken-cd;
+	cd-gpios = <&gpioi 10 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins_a>;
+	cs-gpios = <&gpioz 3 0>;
+	/* Use PIO for the display */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";	/* Enable once there is display driver */
+	/*
+	 * Note: PF3/GPIO_A , PD6/GPIO_B , PG0/GPIO_C , PC6/GPIO_E are
+	 * also connected to the display board connector.
+	 */
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_a>;
+	status = "okay";
+};
+
+/*
+ * Note: PI3 is UART1_RTS and PI5 is UART1_CTS on DRC02 (uart4 of STM32MP1),
+ *       however the STM32MP1 pinmux cannot map them to UART4 .
+ */
+
+&uart8 {	/* RS485 */
+	linux,rs485-enabled-at-boot-time;
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a>;
+	rts-gpios = <&gpioe 6 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};

arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi line 157

Quoted 10 lines
arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi new file +10 -0
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+	vdda1v1-supply = <&reg11>;
+	vdda1v8-supply = <&reg18>;
+};

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel