J2700: Enable various peripherals
cover J2700: Enable various peripherals
Enable USB, HyperFlasha and CPSW on J7200 SoC
Based on top of https://patchwork.ozlabs.org/project/uboot/list/?series=194305
Vignesh Raghavendra (6):
arm: dts: k3-j7200: Add USB related DT entries
board: ti: j721e: Add support for HyperFlash detection
ARM: dts: k3-j7200: Add wkup gpio node
ARM: dts: k3-j7200: Add HyperBus and HyperFlash nodes
ARM: dts: k3-j7200-mcu-wakeup: Add CPSW2G support
arm: dts: k3-j7200-common-proc-board: Enable CPSW2G port
.../k3-j7200-common-proc-board-u-boot.dtsi | 29 ++++ arch/arm/dts/k3-j7200-common-proc-board.dts | 72 ++++++++ arch/arm/dts/k3-j7200-main.dtsi | 30 ++++ arch/arm/dts/k3-j7200-mcu-wakeup.dtsi | 155 ++++++++++++++++++ .../arm/dts/k3-j7200-r5-common-proc-board.dts | 18 ++ arch/arm/dts/k3-j7200-som-p0.dtsi | 33 ++++ arch/arm/dts/k3-j7200.dtsi | 6 +- board/ti/j721e/evm.c | 30 ++++ 8 files changed, 371 insertions(+), 2 deletions(-)
Signature · 1 line
2.28.0
PATCH 1/6 arm: dts: k3-j7200: Add USB related DT entries
Add USB related DT entries to enable USB device mode.
--- .../k3-j7200-common-proc-board-u-boot.dtsi | 14 +++++++++ arch/arm/dts/k3-j7200-common-proc-board.dts | 18 +++++++++++ arch/arm/dts/k3-j7200-main.dtsi | 30 +++++++++++++++++++ .../arm/dts/k3-j7200-r5-common-proc-board.dts | 18 +++++++++++ 4 files changed, 80 insertions(+)
arch/arm/dts/k3-j7200-common-proc-board-u-boot.dtsi +14 -0
@@ -102,3 +102,17 @@ &exp2 { u-boot,dm-spl; }; + +&main_usbss0_pins_default { + u-boot,dm-spl; +}; + +&usbss0 { + u-boot,dm-spl; + ti,usb2-only; +}; + +&usb0 { + dr_mode = "peripheral"; + u-boot,dm-spl; +};
arch/arm/dts/k3-j7200-common-proc-board.dts +18 -0
@@ -30,6 +30,12 @@ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */ >; }; + + main_usbss0_pins_default: main_usbss0_pins_default { + pinctrl-single,pins = < + J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */ + >; + }; }; &wkup_uart0 {
@@ -121,3 +127,15 @@ #gpio-cells = <2>; }; }; + +&usbss0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_usbss0_pins_default>; + ti,vbus-divider; + ti,usb2-only; +}; + +&usb0 { + dr_mode = "otg"; + maximum-speed = "high-speed"; +};
arch/arm/dts/k3-j7200-main.dtsi +30 -0
@@ -310,4 +310,34 @@ clocks = <&k3_clks 193 1>; power-domains = <&k3_pds 193 TI_SCI_PD_EXCLUSIVE>; }; + + usbss0: cdns_usb at 4104000 { + compatible = "ti,j721e-usb"; + reg = <0x00 0x4104000 0x00 0x100>; + dma-coherent; + power-domains = <&k3_pds 288 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 288 12>, <&k3_clks 288 3>; + clock-names = "usb2_refclk", "lpm_clk"; + assigned-clocks = <&k3_clks 288 12>; /* USB2_REFCLK */ + assigned-clock-parents = <&k3_clks 288 13>; /* HFOSC0 */ + #address-cells = <2>; + #size-cells = <2>; + ranges; + + usb0: usb at 6000000 { + compatible = "cdns,usb3"; + reg = <0x00 0x6000000 0x00 0x10000>, + <0x00 0x6010000 0x00 0x10000>, + <0x00 0x6020000 0x00 0x10000>; + reg-names = "otg", "xhci", "dev"; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */ + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, /* irq.6 */ + <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; /* otgirq.0 */ + interrupt-names = "host", + "peripheral", + "otg"; + maximum-speed = "super-speed"; + dr_mode = "otg"; + }; + }; };
arch/arm/dts/k3-j7200-r5-common-proc-board.dts +18 -0
@@ -129,6 +129,12 @@ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */ >; }; + + main_usbss0_pins_default: main_usbss0_pins_default { + pinctrl-single,pins = < + J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */ + >; + }; }; &wkup_uart0 {
@@ -196,4 +202,16 @@ }; }; +&usbss0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_usbss0_pins_default>; + ti,vbus-divider; + ti,usb2-only; +}; + +&usb0 { + dr_mode = "otg"; + maximum-speed = "high-speed"; +}; + #include "k3-j7200-common-proc-board-u-boot.dtsi"
Signature · 1 line
2.28.0
PATCH 2/6 board: ti: j721e: Add support for HyperFlash detection
In reply to Vignesh RaghavendraOn J7200 SoC OSPI0 and HypeFlash are muxed at HW level and only one of them can be used at any time. J7200 EVM has both HyperFlash and OSPI flash on board. There is a user switch (SW3.1) that can be toggled to select OSPI flash vs HyperFlash.
Read the state of this switch via wkup_gpio0_6 line and fixup the DT nodes to select OSPI0 vs HyperFlash
--- board/ti/j721e/evm.c | 30 ++++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+)
board/ti/j721e/evm.c +30 -0
@@ -89,6 +89,34 @@ int board_fit_config_name_match(const char *name) }#endif +#if CONFIG_IS_ENABLED (DM_GPIO ) &&CONFIG_IS_ENABLED (OF_LIBFDT ) +/* Returns 1, if onboard mux is set to hyperflash */ +static void __maybe_unused detect_enable_hyperflash (void *blob) +{ +struct gpio_desc desc = {0 }; + +if (dm_gpio_lookup_name ("6" , &desc)) +return ; + +if (dm_gpio_request (&desc,"6" )) +return ; + +if (dm_gpio_set_dir_flags (&desc,GPIOD_IS_IN )) +return ; + +if (dm_gpio_get_value (&desc)) { +int offset; + +do_fixup_by_compat (blob,"ti,am654-hbmc" ,"status" , +"okay" ,sizeof ("okay" ),0 ); + offset =fdt_node_offset_by_compatible (blob,-1 , +"ti,j721e-ospi" ); +fdt_setprop (blob, offset,"status" ,"disabled" , +sizeof ("disabled" )); + } +} +#endif +#if defined(CONFIG_OF_LIBFDT ) && defined(CONFIG_OF_BOARD_SETUP )int ft_board_setup (void *blob,struct bd_info *bd) {
@@ -101,6 +129,8 @@ int ft_board_setup(void *blob, struct bd_info *bd)if (ret)printf ("%s: fixing up msmc ram failed %d\n" , __func__, ret); +detect_enable_hyperflash (blob); + return ret; }#endif
Signature · 1 line
2.28.0
PATCH 3/6 ARM: dts: k3-j7200: Add wkup gpio node
In reply to Vignesh RaghavendraAdd wkup_gpio0 node required for detecting whether board mux is set HyperFlash.
--- arch/arm/dts/k3-j7200-common-proc-board.dts | 11 +++++++++++ arch/arm/dts/k3-j7200-mcu-wakeup.dtsi | 12 ++++++++++++ 2 files changed, 23 insertions(+)
arch/arm/dts/k3-j7200-common-proc-board.dts +11 -0
@@ -21,6 +21,12 @@ J721E_WKUP_IOPAD(0x104, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */ >; }; + + wkup_gpio_pins_default: wkup-gpio-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0xd8, PIN_INPUT, 7) /* (C14) WKUP_GPIO0_6 */ + >; + }; }; &main_pmx0 {
@@ -139,3 +145,8 @@ dr_mode = "otg"; maximum-speed = "high-speed"; }; + +&wkup_gpio0 { + pinctrl-names = "default"; + pinctrl-0 = <&wkup_gpio_pins_default>; +};
arch/arm/dts/k3-j7200-mcu-wakeup.dtsi +12 -0
@@ -114,4 +114,16 @@ clocks = <&k3_clks 195 1>; power-domains = <&k3_pds 195 TI_SCI_PD_EXCLUSIVE>; }; + + wkup_gpio0: gpio at 42110000 { + compatible = "ti,j721e-gpio", "ti,keystone-gpio"; + reg = <0x0 0x42110000 0x0 0x100>; + gpio-controller; + #gpio-cells = <2>; + ti,ngpio = <84>; + ti,davinci-gpio-unbanked = <0>; + power-domains = <&k3_pds 113 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 113 0>; + clock-names = "gpio"; + }; };
Signature · 1 line
2.28.0
PATCH 4/6 ARM: dts: k3-j7200: Add HyperBus and HyperFlash nodes
In reply to Vignesh RaghavendraJ7200 SoM has Cypress HyperFlash connected to HyperBus interface, add DT entries for the same.
--- arch/arm/dts/k3-j7200-mcu-wakeup.dtsi | 27 ++++++++++++++++++++++ arch/arm/dts/k3-j7200-som-p0.dtsi | 33 +++++++++++++++++++++++++++ arch/arm/dts/k3-j7200.dtsi | 6 +++-- 3 files changed, 64 insertions(+), 2 deletions(-)
arch/arm/dts/k3-j7200-mcu-wakeup.dtsi +27 -0
@@ -93,6 +93,33 @@ clock-names = "fclk"; }; + fss: system-controller at 47000000 { + compatible = "syscon", "simple-mfd"; + reg = <0x0 0x47000000 0x0 0x100>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + hbmc_mux: hbmc-mux { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x4 0x2>; /* HBMC select */ + }; + + hbmc: hyperbus at 47034000 { + compatible = "ti,am654-hbmc"; + reg = <0x0 0x47034000 0x0 0x100>, + <0x5 0x00000000 0x1 0x0000000>; + power-domains = <&k3_pds 102 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <2>; + #size-cells = <1>; + mux-controls = <&hbmc_mux 0>; + clocks = <&k3_clks 102 5>; + assigned-clocks = <&k3_clks 102 5>; + assigned-clock-rates = <333333333>; + }; + }; + mcu_i2c0: i2c at 40b00000 { compatible = "ti,j721e-i2c", "ti,omap4-i2c"; reg = <0x0 0x40b00000 0x0 0x100>;
arch/arm/dts/k3-j7200-som-p0.dtsi +33 -0
@@ -27,3 +27,36 @@ }; }; }; + +&wkup_pmx0 { + mcu_fss0_hpb0_pins_default: mcu-fss0-hpb0-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 1) /* (B6) MCU_OSPI0_CLK.MCU_HYPERBUS0_CK */ + J721E_WKUP_IOPAD(0x4, PIN_OUTPUT, 1) /* (C8) MCU_OSPI0_LBCLKO.MCU_HYPERBUS0_CKn */ + J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 1) /* (D6) MCU_OSPI0_CSn0.MCU_HYPERBUS0_CSn0 */ + J721E_WKUP_IOPAD(0x30, PIN_OUTPUT, 1) /* (D7) MCU_OSPI0_CSn1.MCU_HYPERBUS0_RESETn */ + J721E_WKUP_IOPAD(0x8, PIN_INPUT, 1) /* (B7) MCU_OSPI0_DQS.MCU_HYPERBUS0_RWDS */ + J721E_WKUP_IOPAD(0xc, PIN_INPUT, 1) /* (D8) MCU_OSPI0_D0.MCU_HYPERBUS0_DQ0 */ + J721E_WKUP_IOPAD(0x10, PIN_INPUT, 1) /* (C7) MCU_OSPI0_D1.MCU_HYPERBUS0_DQ1 */ + J721E_WKUP_IOPAD(0x14, PIN_INPUT, 1) /* (C5) MCU_OSPI0_D2.MCU_HYPERBUS0_DQ2 */ + J721E_WKUP_IOPAD(0x18, PIN_INPUT, 1) /* (A5) MCU_OSPI0_D3.MCU_HYPERBUS0_DQ3 */ + J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 1) /* (A6) MCU_OSPI0_D4.MCU_HYPERBUS0_DQ4 */ + J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* (B8) MCU_OSPI0_D5.MCU_HYPERBUS0_DQ5 */ + J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* (A8) MCU_OSPI0_D6.MCU_HYPERBUS0_DQ6 */ + J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (A7) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */ + >; + }; +}; + +&hbmc { + status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&mcu_fss0_hpb0_pins_default>; + ranges = <0x0 0x0 0x5 0x0 0x4000000>, /* 64MB Flash on CS0 */ + <0x1 0x0 0x5 0x4000000 0x800000>; /* 8MB RAM on CS1 */ + + flash at 0,0 { + compatible = "cypress,hyperflash", "cfi-flash"; + reg = <0x0 0x0 0x4000000>; + }; +};
arch/arm/dts/k3-j7200.dtsi +4 -2
@@ -149,7 +149,8 @@ <0x00 0x45100000 0x00 0x45100000 0x00 0x00c24000>, <0x00 0x46000000 0x00 0x46000000 0x00 0x00200000>, <0x00 0x47000000 0x00 0x47000000 0x00 0x00068400>, - <0x00 0x50000000 0x00 0x50000000 0x00 0x10000000>; + <0x00 0x50000000 0x00 0x50000000 0x00 0x10000000>, + <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>; cbass_mcu_wakeup: bus at 28380000 { compatible = "simple-bus";
@@ -165,7 +166,8 @@ <0x00 0x45100000 0x00 0x45100000 0x00 0x00c24000>, /* MMRs, remaining NAVSS */ <0x00 0x46000000 0x00 0x46000000 0x00 0x00200000>, /* CPSW */ <0x00 0x47000000 0x00 0x47000000 0x00 0x00068400>, /* OSPI register space */ - <0x00 0x50000000 0x00 0x50000000 0x00 0x10000000>; /* FSS OSPI0/1 data region 0 */ + <0x00 0x50000000 0x00 0x50000000 0x00 0x10000000>, /* FSS OSPI0/1 data region 0 */ + <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>; /* FSS OSPI0 data region 3 */ }; }; };
Signature · 1 line
2.28.0
PATCH 5/6 ARM: dts: k3-j7200-mcu-wakeup: Add CPSW2G support
In reply to Vignesh RaghavendraAdd MCU NAVSS, UDMA and CPSW2G DT nodes.
--- arch/arm/dts/k3-j7200-mcu-wakeup.dtsi | 116 ++++++++++++++++++++++++++ 1 file changed, 116 insertions(+)
arch/arm/dts/k3-j7200-mcu-wakeup.dtsi +116 -0
@@ -142,6 +142,49 @@ power-domains = <&k3_pds 195 TI_SCI_PD_EXCLUSIVE>; }; + cbass_mcu_navss: mcu-navss { + compatible = "simple-mfd"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + dma-coherent; + dma-ranges; + + ti,sci-dev-id = <232>; + + mcu_ringacc: ringacc at 2b800000 { + compatible = "ti,am654-navss-ringacc"; + reg = <0x0 0x2b800000 0x0 0x400000>, + <0x0 0x2b000000 0x0 0x400000>, + <0x0 0x28590000 0x0 0x100>, + <0x0 0x2a500000 0x0 0x40000>; + reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target"; + ti,num-rings = <286>; + ti,sci-rm-range-gp-rings = <0x1>; /* GP ring range */ + ti,sci = <&dmsc>; + ti,sci-dev-id = <235>; + }; + + mcu_udmap: dma-controller at 285c0000 { + compatible = "ti,j721e-navss-mcu-udmap"; + reg = <0x0 0x285c0000 0x0 0x100>, + <0x0 0x2a800000 0x0 0x40000>, + <0x0 0x2aa00000 0x0 0x40000>; + reg-names = "gcfg", "rchanrt", "tchanrt"; + #dma-cells = <1>; + + ti,sci = <&dmsc>; + ti,sci-dev-id = <236>; + ti,ringacc = <&mcu_ringacc>; + + ti,sci-rm-range-tchan = <0x0d>, /* TX_CHAN */ + <0x0f>; /* TX_HCHAN */ + ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */ + <0x0b>; /* RX_HCHAN */ + ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */ + }; + }; + wkup_gpio0: gpio at 42110000 { compatible = "ti,j721e-gpio", "ti,keystone-gpio"; reg = <0x0 0x42110000 0x0 0x100>;
@@ -153,4 +196,77 @@ clocks = <&k3_clks 113 0>; clock-names = "gpio"; }; + + mcu_conf: scm_conf at 40f00000 { + compatible = "syscon", "simple-mfd"; + reg = <0x0 0x40f00000 0x0 0x20000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x40f00000 0x20000>; + + phy_gmii_sel: phy at 4040 { + compatible = "ti,am654-cpsw-phy-sel"; + reg = <0x4040 0x4>; + reg-names = "gmii-sel"; + #phy-cells = <1>; + }; + }; + + mcu_cpsw: ethernet at 46000000 { + compatible = "ti,j721e-cpsw-nuss"; + #address-cells = <2>; + #size-cells = <2>; + reg = <0x0 0x46000000 0x0 0x200000>; + reg-names = "cpsw_nuss"; + ranges; + dma-coherent; + clocks = <&k3_clks 18 21>; + clock-names = "fck"; + power-domains = <&k3_pds 18 TI_SCI_PD_EXCLUSIVE>; + + dmas = <&mcu_udmap 0xf000>, + <&mcu_udmap 0xf001>, + <&mcu_udmap 0xf002>, + <&mcu_udmap 0xf003>, + <&mcu_udmap 0xf004>, + <&mcu_udmap 0xf005>, + <&mcu_udmap 0xf006>, + <&mcu_udmap 0xf007>, + <&mcu_udmap 0x7000>; + dma-names = "tx0", "tx1", "tx2", "tx3", + "tx4", "tx5", "tx6", "tx7", + "rx"; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + cpsw_port1: port at 1 { + reg = <1>; + ti,mac-only; + ti,label = "port1"; + ti,syscon-efuse = <&mcu_conf 0x200>; + phys = <&phy_gmii_sel 1>; + }; + }; + + davinci_mdio: mdio at f00 { + compatible = "ti,cpsw-mdio","ti,davinci_mdio"; + reg = <0x0 0xf00 0x0 0x100>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&k3_clks 18 21>; + clock-names = "fck"; + bus_freq = <1000000>; + }; + + cpts { + clocks = <&k3_clks 18 2>; + clock-names = "cpts"; + interrupts-extended = <&gic500 GIC_SPI 858 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cpts"; + ti,cpts-ext-ts-inputs = <4>; + ti,cpts-periodic-outputs = <2>; + }; + }; };
Signature · 1 line
2.28.0
PATCH 6/6 arm: dts: k3-j7200-common-proc-board: Enable CPSW2G port
In reply to Vignesh RaghavendraEnable CPSW2G port to support networking in U-Boot
--- .../k3-j7200-common-proc-board-u-boot.dtsi | 15 +++++++ arch/arm/dts/k3-j7200-common-proc-board.dts | 43 +++++++++++++++++++ 2 files changed, 58 insertions(+)
arch/arm/dts/k3-j7200-common-proc-board-u-boot.dtsi +15 -0
@@ -9,6 +9,9 @@ tick-timer = &timer1; }; + aliases { + ethernet0 = &cpsw_port1; + }; }; &chipid {
@@ -103,6 +106,18 @@ u-boot,dm-spl; }; +&mcu_cpsw { + reg = <0x0 0x46000000 0x0 0x200000>, + <0x0 0x40f00200 0x0 0x8>; + reg-names = "cpsw_nuss", "mac_efuse"; + + cpsw-phy-sel at 40f04040 { + compatible = "ti,am654-cpsw-phy-sel"; + reg= <0x0 0x40f04040 0x0 0x4>; + reg-names = "gmii-sel"; + }; +}; + &main_usbss0_pins_default { u-boot,dm-spl; };
arch/arm/dts/k3-j7200-common-proc-board.dts +43 -0
58 lines not on this page · raw message
Signature · 1 line
2.28.0
cover J2700: Enable various peripherals
In reply to Vignesh RaghavendraQuoted 12 lines · Vignesh Raghavendra
Enable USB, HyperFlasha and CPSW on J7200 SoC
Based on top of https://patchwork.ozlabs.org/project/uboot/list/?series=194305
Vignesh Raghavendra (6):
arm: dts: k3-j7200: Add USB related DT entries
board: ti: j721e: Add support for HyperFlash detection
ARM: dts: k3-j7200: Add wkup gpio node
ARM: dts: k3-j7200: Add HyperBus and HyperFlash nodes
ARM: dts: k3-j7200-mcu-wakeup: Add CPSW2G support
arm: dts: k3-j7200-common-proc-board: Enable CPSW2G port
Quoted 10 lines
.../k3-j7200-common-proc-board-u-boot.dtsi | 29 ++++ arch/arm/dts/k3-j7200-common-proc-board.dts | 72 ++++++++ arch/arm/dts/k3-j7200-main.dtsi | 30 ++++ arch/arm/dts/k3-j7200-mcu-wakeup.dtsi | 155 ++++++++++++++++++ .../arm/dts/k3-j7200-r5-common-proc-board.dts | 18 ++ arch/arm/dts/k3-j7200-som-p0.dtsi | 33 ++++ arch/arm/dts/k3-j7200.dtsi | 6 +- board/ti/j721e/evm.c | 30 ++++ 8 files changed, 371 insertions(+), 2 deletions(-)
Signature · 2 lines
Best regards, grygorii
cover J2700: Enable various peripherals
In reply to Vignesh RaghavendraQuoted 1 line · Vignesh Raghavendra
Enable USB, HyperFlasha and CPSW on J7200 SoC
$subject: s/J2700/J7200 :)
Thanks and regards,
Lokesh
Quoted 21 lines
Based on top of https://patchwork.ozlabs.org/project/uboot/list/?series=194305
Vignesh Raghavendra (6):
arm: dts: k3-j7200: Add USB related DT entries
board: ti: j721e: Add support for HyperFlash detection
ARM: dts: k3-j7200: Add wkup gpio node
ARM: dts: k3-j7200: Add HyperBus and HyperFlash nodes
ARM: dts: k3-j7200-mcu-wakeup: Add CPSW2G support
arm: dts: k3-j7200-common-proc-board: Enable CPSW2G port.../k3-j7200-common-proc-board-u-boot.dtsi | 29 ++++ arch/arm/dts/k3-j7200-common-proc-board.dts | 72 ++++++++ arch/arm/dts/k3-j7200-main.dtsi | 30 ++++ arch/arm/dts/k3-j7200-mcu-wakeup.dtsi | 155 ++++++++++++++++++ .../arm/dts/k3-j7200-r5-common-proc-board.dts | 18 ++ arch/arm/dts/k3-j7200-som-p0.dtsi | 33 ++++ arch/arm/dts/k3-j7200.dtsi | 6 +- board/ti/j721e/evm.c | 30 ++++ 8 files changed, 371 insertions(+), 2 deletions(-)
cover J2700: Enable various peripherals
In reply to Vignesh RaghavendraQuoted 3 lines · Vignesh Raghavendra
Enable USB, HyperFlasha and CPSW on J7200 SoC
Based on top of https://patchwork.ozlabs.org/project/uboot/list/?series=194305
Applied to u-boot-ti
Thanks and regards,
Lokesh