remoteproc: Add initial zynqmp R5 remoteproc driver
Subsystems (2)
PATCH v8 5/5 remoteproc: Add initial zynqmp R5 remoteproc driver
R5 is included in Xilinx Zynq UltraScale MPSoC so by adding this remotproc driver, we can boot the R5 sub-system in different configurations.
---
v2:
- remove domain struct as per review from Mathieu
v3:
- add xilinx-related platform mgmt fn's instead of wrapping around function pointer in xilinx eemi ops struct
v4:
- add default values for enums
- fix formatting as per checkpatch.pl --strict. Note that 1 warning and 1 check are still raised as each is due to fixing the warning results in that
particular line going over 80 characters.
v5:
- parse_fw change from use of rproc_of_resm_mem_entry_init to rproc_mem_entry_init and use of alloc/release
- var's of type zynqmp_r5_pdata all have same local variable name
- use dev_dbg instead of dev_info
v6:
- adding memory carveouts is handled much more similarly. All mem carveouts are
now described in reserved memory as needed. That is, TCM nodes are not coupled to remoteproc anymore. This is reflected in the remoteproc R5
driver
and the device tree binding.
- remove mailbox from device tree binding as it is not necessary for elf loading
- use lockstep-mode property for configuring RPU
v7:
- remove unused headers
- change u32 *lockstep_mode -> u32 lockstep_mode;
- change device-tree binding "lockstep-mode" to xlnx,cluster-mode
- remove zynqmp_r5_mem_probe and loop to Probe R5 memory devices at remoteproc-probe time
- remove is_r5_mode_set from zynqmp rpu remote processor private data
- do not error out if no mailbox is provided
- remove zynqmp_r5_remoteproc_probe call of platform_set_drvdata as pdata is
handled in zynqmp_r5_remoteproc_remove
v8:
- remove old acks, reviewed-by's in commit message
--- drivers/remoteproc/Kconfig | 10 + drivers/remoteproc/Makefile | 1 + drivers/remoteproc/zynqmp_r5_remoteproc.c | 911 ++++++++++++++++++++++ 3 files changed, 922 insertions(+) create mode 100644 drivers/remoteproc/zynqmp_r5_remoteproc.c
drivers/remoteproc/Kconfig +10 -0
@@ -249,6 +249,16 @@ config STM32_RPROC This can be either built-in or a loadable module. +config ZYNQMP_R5_REMOTEPROC + tristate "ZynqMP_R5 remoteproc support" + depends on ARM64 && PM && ARCH_ZYNQMP + select RPMSG_VIRTIO + select MAILBOX + select ZYNQMP_IPI_MBOX + help + Say y here to support ZynqMP R5 remote processors via the remote + processor framework. + endif # REMOTEPROC endmenu
drivers/remoteproc/Makefile +1 -0
@@ -28,5 +28,6 @@ obj-$(CONFIG_QCOM_WCNSS_PIL) += qcom_wcnss_pil.o qcom_wcnss_pil-y += qcom_wcnss.o qcom_wcnss_pil-y += qcom_wcnss_iris.o obj-$(CONFIG_ST_REMOTEPROC) += st_remoteproc.o +obj-$(CONFIG_ZYNQMP_R5_REMOTEPROC) += zynqmp_r5_remoteproc.o obj-$(CONFIG_ST_SLIM_REMOTEPROC) += st_slim_rproc.o obj-$(CONFIG_STM32_RPROC) += stm32_rproc.o
drivers/remoteproc/zynqmp_r5_remoteproc.c new file +911 -0
911 lines not on this page · raw message
Signature · 1 line
2.17.1