dt-bindings: Add DT bindings for RaspberryPi 7" display ATTINY88-based regulator/backlight controller
Subsystems (3)
PATCH 1/2 dt-bindings: Add DT bindings for RaspberryPi 7" display ATTINY88-based regulator/backlight controller
Add DT bindings for RaspberryPi 7" display ATTINY88-based regulator/backlight controller, this one is used in the Raspberry Pi 7" touchscreen display unit.
To: [email protected]
Cc: Eric Anholt <[email protected]>
Cc: Mark Brown <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: Sam Ravnborg <[email protected]>
Cc: [email protected]
--- ...ypi,7inch-touchscreen-panel-regulator.yaml | 44 +++++++++++++++++++ 1 file changed, 44 insertions(+) create mode 100644 Documentation/devicetree/bindings/regulator/raspberrypi,7inch-touchscreen-panel-regulator.yaml
Documentation/devicetree/bindings/regulator/raspberrypi,7inch-touchscreen-panel-regulator.yaml new file +44 -0
@@ -0,0 +1,44 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/raspberrypi,7inch-touchscreen-panel-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RaspberryPi 7" display ATTINY88-based regulator/backlight controller + +maintainers: + - Marek Vasut <[email protected]> + +description: | + The RaspberryPi 7" display has an ATTINY88-based regulator/backlight + controller on the PCB, which is used to turn the display unit on/off + and control the backlight. + +allOf: + - $ref: "regulator.yaml#" + +properties: + compatible: + const: raspberrypi,7inch-touchscreen-panel-regulator + + reg: + maxItems: 1 + +additionalProperties: false + +required: + - compatible + - reg + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + regulator@45 { + compatible = "raspberrypi,7inch-touchscreen-panel-regulator"; + reg = <0x45>; + }; + }; + +...
Signature · 1 line
2.28.0
PATCH 2/2 regulator: rpi-panel: Add regulator/backlight driver for RPi panel
This regulator/backlight driver handles the ATTINY88 present on the RPi 7" touchscreen panel and exposes the power/backlight interfaces.
To: [email protected]
Cc: Eric Anholt <[email protected]>
Cc: Mark Brown <[email protected]>
Cc: Sam Ravnborg <[email protected]>
--- drivers/regulator/Kconfig | 10 + drivers/regulator/Makefile | 1 + .../regulator/rpi-panel-attiny-regulator.c | 214 ++++++++++++++++++ 3 files changed, 225 insertions(+) create mode 100644 drivers/regulator/rpi-panel-attiny-regulator.c
drivers/regulator/Kconfig +10 -0
@@ -864,6 +864,16 @@ config REGULATOR_QCOM_USB_VBUS Say M here if you want to include support for enabling the VBUS output as a module. The module will be named "qcom_usb_vbus_regulator". +config REGULATOR_RASPBERRYPI_TOUCHSCREEN_ATTINY + tristate "Raspberry Pi 7-inch touchscreen panel ATTINY regulator" + depends on BACKLIGHT_CLASS_DEVICE + depends on I2C + select REGMAP_I2C + help + This driver supports ATTINY regulator on the Raspberry Pi 7-inch + touchscreen unit. The regulator is used to enable power to the + TC358762, display and to control backlight. + config REGULATOR_RC5T583 tristate "RICOH RC5T583 Power regulators" depends on MFD_RC5T583
drivers/regulator/Makefile +1 -0
@@ -107,6 +107,7 @@ obj-$(CONFIG_REGULATOR_TPS51632) += tps51632-regulator.o obj-$(CONFIG_REGULATOR_PBIAS) += pbias-regulator.o obj-$(CONFIG_REGULATOR_PCAP) += pcap-regulator.o obj-$(CONFIG_REGULATOR_PCF50633) += pcf50633-regulator.o +obj-$(CONFIG_REGULATOR_RASPBERRYPI_TOUCHSCREEN_ATTINY) += rpi-panel-attiny-regulator.o obj-$(CONFIG_REGULATOR_RC5T583) += rc5t583-regulator.o obj-$(CONFIG_REGULATOR_RK808) += rk808-regulator.o obj-$(CONFIG_REGULATOR_RN5T618) += rn5t618-regulator.o
drivers/regulator/rpi-panel-attiny-regulator.c new file +214 -0
214 lines not on this page · raw message
Signature · 6 lines
2.28.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Mark Brown
maintainerQuoted 3 lines · Marek Vasut
Add DT bindings for RaspberryPi 7" display ATTINY88-based regulator/backlight controller, this one is used in the Raspberry Pi 7" touchscreen display unit.
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git for-next
Thanks!
[1/2] regulator: Add DT bindings for RaspberryPi 7" display ATTINY88-based regulator/backlight controller
commit: 9c535960891470eaec5664eed2a56dbb2b6a205b
[2/2] regulator: rpi-panel: Add regulator/backlight driver for RPi panel
commit: 38573472278da49e2ab588062d88bc2f0c11a325All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel