mm-slub-extend-slub_debug-syntax-for-multiple-blocks.patch removed from -mm tree
The patch titled
Subject: mm, slub: extend slub_debug syntax for multiple blocks
has been removed from the -mm tree. Its filename was
mm-slub-extend-slub_debug-syntax-for-multiple-blocks.patch
This patch was dropped because it was merged into mainline or a subsystem tree
------------------------------------------------------
From: Vlastimil Babka <[email protected]>
Subject: mm, slub: extend slub_debug syntax for multiple blocks
Patch series "slub_debug fixes and improvements".
The slub_debug kernel boot parameter can either apply a single set of options to all caches or a list of caches. There is a use case where debugging is applied for all caches and then disabled at runtime for specific caches, for performance and memory consumption reasons [1]. As runtime changes are dangerous, extend the boot parameter syntax so that multiple blocks of either global or slab-specific options can be specified, with blocks delimited by ';'. This will also support the use case of [1] without runtime changes.
For details see the updated Documentation/vm/slub.rst
[1] https://lore.kernel.org/r/[email protected]
---
Documentation/admin-guide/kernel-parameters.txt | 2 Documentation/vm/slub.rst | 18 + mm/slub.c | 179 +++++++++----- 3 files changed, 146 insertions(+), 53 deletions(-)
Documentation/admin-guide/kernel-parameters.txt renamed from Documentation/admin-guide/kernel-parameters.txt~mm-slub-extend-slub_debug-syntax-for-multiple-blocks +1 -1
@@ -4689,7 +4689,7 @@ fragmentation. Defaults to 1 for systems with more than 32MB of RAM, 0 otherwise. - slub_debug[=options[,slabs]] [MM, SLUB] + slub_debug[=options[,slabs][;[options[,slabs]]...] [MM, SLUB] Enabling slub_debug allows one to determine the culprit if slab objects become corrupted. Enabling slub_debug can create guard zones around objects and
Documentation/vm/slub.rst renamed from Documentation/vm/slub.rst~mm-slub-extend-slub_debug-syntax-for-multiple-blocks +18 -0
@@ -41,6 +41,11 @@ slub_debug=<Debug-Options>,<slab name1>, Enable options only for select slabs (no spaces after a comma) +Multiple blocks of options for all slabs or selected slabs can be given, with +blocks of options delimited by ';'. The last of "all slabs" blocks is applied +to all slabs except those that match one of the "select slabs" block. Options +of the first "select slabs" blocks that matches the slab's name are applied. + Possible debug options are:: F Sanity checks on (enables SLAB_DEBUG_CONSISTENCY_CHECKS
@@ -83,6 +88,19 @@ switch off debugging for such caches by slub_debug=O +You can apply different options to different list of slab names, using blocks +of options. This will enable red zoning for dentry and user tracking for +kmalloc. All other slabs will not get any debugging enabled:: + + slub_debug=Z,dentry;U,kmalloc-* + +You can also enable options (e.g. sanity checks and poisoning) for all caches +except some that are deemed too performance critical and don't need to be +debugged by specifying global debug options followed by a list of slab names +with "-" as options:: + + slub_debug=FZ;-,zs_handle,zspage + In case you forgot to enable debugging on the kernel command line: It is possible to enable debugging manually when the kernel is up. Look at the contents of::
mm/slub.c renamed from mm/slub.c~mm-slub-extend-slub_debug-syntax-for-multiple-blocks +127 -52
238 lines not on this page · raw message
_
Patches currently in -mm which might be from [email protected] are