dt-bindings: arm: fsl: Add binding for Variscite VAR-SOM-MX8MM module
Subsystems (2)
PATCH v2 1/4 dt-bindings: arm: fsl: Add binding for Variscite VAR-SOM-MX8MM module
Add a binding for the Variscite VAR-SOM-MX8MM System on Module.
---
Changes since v1:
1. None
--- Documentation/devicetree/bindings/arm/fsl.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/fsl.yaml +1 -0
@@ -342,6 +342,7 @@ properties: items: - enum: - fsl,imx8mm-evk # i.MX8MM EVK Board + - variscite,var-som-mx8mm # i.MX8MM Variscite VAR-SOM-MX8MM module - const: fsl,imx8mm - description: i.MX8MN based Boards
Signature · 1 line
2.17.1
PATCH v2 2/4 dt-bindings: arm: fsl: Add binding for Variscite Symphony board with VAR-SOM-MX8MM
Add a binding for the Variscite Symphony evaluation kit board with VAR-SOM-MX8MM System on Module.
---
Changes since v1:
1. None
--- Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++ 1 file changed, 6 insertions(+)
Documentation/devicetree/bindings/arm/fsl.yaml +6 -0
@@ -345,6 +345,12 @@ properties: - variscite,var-som-mx8mm # i.MX8MM Variscite VAR-SOM-MX8MM module - const: fsl,imx8mm + - description: Variscite VAR-SOM-MX8MM based boards + items: + - const: variscite,var-som-mx8mm-symphony + - const: variscite,var-som-mx8mm + - const: fsl,imx8mm + - description: i.MX8MN based Boards items: - enum:
Signature · 1 line
2.17.1
PATCH v2 3/4 arm64: dts: imx8mm-var-som: Add Variscite VAR-SOM-MX8MM System on Module
In reply to Krzysztof KozlowskiAdd DTSI of Variscite VAR-SOM-MX8MM System on Module in a basic version, delivered with Variscite Symphony Evaluation kit. This version comes with:
- 2 GB of RAM,
- 16 GB eMMC,
- Gigabit Ethernet PHY,
- 802.11 ac/a/b/g/n WiFi with 4.2 Bluetooth (Cypress CYW43353),
- CAN bus,
- Audio codec (not yet configured in DTSI).
---
Changes since v1:
1. None
--- .../boot/dts/freescale/imx8mm-var-som.dtsi | 579 ++++++++++++++++++ 1 file changed, 579 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +579 -0
@@ -0,0 +1,579 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2019 NXP + * Copyright (C) 2020 Krzysztof Kozlowski <[email protected]> + */ + +#include "imx8mm.dtsi" + +/ { + model = "Variscite VAR-SOM-MX8MM module"; + compatible = "variscite,var-som-mx8mm", "fsl,imx8mm"; + + chosen { + stdout-path = &uart4; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0x0 0x40000000 0 0x80000000>; + }; + + reg_eth_phy: regulator-0 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_eth_phy>; + regulator-name = "eth_phy_pwr"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&A53_0 { + cpu-supply = <&buck2_reg>; +}; + +&A53_1 { + cpu-supply = <&buck2_reg>; +}; + +&A53_2 { + cpu-supply = <&buck2_reg>; +}; + +&A53_3 { + cpu-supply = <&buck2_reg>; +}; + +&ddrc { + operating-points-v2 = <&ddrc_opp_table>; + + ddrc_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-25M { + opp-hz = /bits/ 64 <25000000>; + }; + + opp-100M { + opp-hz = /bits/ 64 <100000000>; + }; + + opp-750M { + opp-hz = /bits/ 64 <750000000>; + }; + }; +}; + +&ecspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + cs-gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>, + <&gpio1 0 GPIO_ACTIVE_HIGH>; + fsl,spi-num-chipselects = <2>; + /delete-property/ dmas; + /delete-property/ dma-names; + status = "okay"; + + /* Resistive touch controller */ + touchscreen@0 { + reg = <0>; + compatible = "ti,ads7846"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_restouch>; + interrupt-parent = <&gpio1>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + + spi-max-frequency = <1500000>; + pendown-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; + + ti,x-min = /bits/ 16 <125>; + touchscreen-size-x = /bits/ 16 <4008>; + ti,y-min = /bits/ 16 <282>; + touchscreen-size-y = /bits/ 16 <3864>; + ti,x-plate-ohms = /bits/ 16 <180>; + touchscreen-max-pressure = /bits/ 16 <255>; + touchscreen-average-samples = /bits/ 16 <10>; + ti,debounce-tol = /bits/ 16 <3>; + ti,debounce-rep = /bits/ 16 <1>; + ti,settle-delay-usec = /bits/ 16 <150>; + ti,keep-vref-on; + wakeup-source; + }; + + can: can@1 { + /* TODO: binding not documented, patches on the LKML */ + compatible = "microchip,mcp2517fd"; + reg = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can>; + interrupt-parent = <&gpio1>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + spi-max-frequency = <20000000>; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii"; + phy-handle = <ðphy>; + phy-supply = <®_eth_phy>; + phy-reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + phy-reset-duration = <100>; + phy-reset-post-delay = <100>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <4>; + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic@4b { + compatible = "rohm,bd71847"; + reg = <0x4b>; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio2>; + interrupts = <8 GPIO_ACTIVE_LOW>; + rohm,reset-snvs-powered; + + regulators { + buck1_reg: BUCK1 { + regulator-name = "BUCK1"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + }; + + buck2_reg: BUCK2 { + regulator-name = "BUCK2"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <1000000>; + rohm,dvs-idle-voltage = <900000>; + }; + + buck3_reg: BUCK3 { + regulator-name = "BUCK3"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + regulator-always-on; + }; + + buck4_reg: BUCK4 { + regulator-name = "BUCK4"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5_reg: BUCK5 { + regulator-name = "BUCK5"; + regulator-min-microvolt = <1605000>; + regulator-max-microvolt = <1995000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6_reg: BUCK6 { + regulator-name = "BUCK6"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: LDO1 { + regulator-name = "LDO1"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <1900000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "LDO2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "LDO3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "LDO4"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo5_reg: LDO5 { + regulator-compatible = "LDO5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo6_reg: LDO6 { + regulator-name = "LDO6"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + /* TODO: configure audio, as of now just put a placeholder */ + wm8904: codec@1a { + compatible = "wlf,wm8904"; + reg = <0x1a>; + status = "disabled"; + }; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +/* Bluetooth */ +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + assigned-clocks = <&clk IMX8MM_CLK_UART2>; + assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>; + uart-has-rtscts; + status = "okay"; +}; + +/* Console */ +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbotg1 { + dr_mode = "otg"; + usb-role-switch; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "otg"; + usb-role-switch; + status = "okay"; +}; + +/* WIFI */ +&usdhc1 { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + bus-width = <4>; + non-removable; + keep-power-in-suspend; + status = "okay"; + + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +/* SD */ +&usdhc2 { + assigned-clocks = <&clk IMX8MM_CLK_USDHC2>; + assigned-clock-rates = <200000000>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + cd-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <®_usdhc2_vmmc>; + status = "okay"; +}; + +/* eMMC */ +&usdhc3 { + assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>; + assigned-clock-rates = <400000000>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + + pinctrl_can: cangrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x16 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x13 + MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x13 + MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x13 + MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x13 + MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x13 + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 + >; + }; + + pinctrl_pcie0: pcie0grp { + fsl,pins = < + MX8MM_IOMUXC_SAI2_RXFS_GPIO4_IO21 0x41 + >; + }; + + pinctrl_pmic: pmicirq { + fsl,pins = < + MX8MM_IOMUXC_SD1_DATA6_GPIO2_IO8 0x41 + >; + }; + + pinctrl_reg_eth_phy: regethphygrp { + fsl,pins = < + MX8MM_IOMUXC_SD1_DATA7_GPIO2_IO9 0x41 + >; + }; + + pinctrl_restouch: restouchgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x1c0 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x140 + MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x140 + MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x140 + MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x140 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140 + MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1grp100mhz { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1grp200mhz { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2grpgpio { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0xc1 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3grp100mhz { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3grp200mhz { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + >; + }; +};
Signature · 1 line
2.17.1
Re: [PATCH v2 3/4] arm64: dts: imx8mm-var-som: Add Variscite VAR-SOM-MX8MM System on Module
Quoted 92 lines · Krzysztof Kozlowski
Add DTSI of Variscite VAR-SOM-MX8MM System on Module in a basic version, delivered with Variscite Symphony Evaluation kit. This version comes with:
- 2 GB of RAM,
- 16 GB eMMC,
- Gigabit Ethernet PHY,
- 802.11 ac/a/b/g/n WiFi with 4.2 Bluetooth (Cypress CYW43353),
- CAN bus,
- Audio codec (not yet configured in DTSI).Signed-off-by Krzysztof Kozlowski <[email protected]>---
Changes since v1:
1. None--- .../boot/dts/freescale/imx8mm-var-som.dtsi | 579 ++++++++++++++++++ 1 file changed, 579 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsiarch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +65
-0@@ -0,0 +1,579 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2019 NXP + * Copyright (C) 2020 Krzysztof Kozlowski <[email protected]> + */ + +#include "imx8mm.dtsi" + +/ { + model = "Variscite VAR-SOM-MX8MM module"; + compatible = "variscite,var-som-mx8mm", "fsl,imx8mm"; + + chosen { + stdout-path = &uart4; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0x0 0x40000000 0 0x80000000>; + }; + + reg_eth_phy: regulator-0 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_eth_phy>; + regulator-name = "eth_phy_pwr"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&A53_0 { + cpu-supply = <&buck2_reg>; +}; + +&A53_1 { + cpu-supply = <&buck2_reg>; +}; + +&A53_2 { + cpu-supply = <&buck2_reg>; +}; + +&A53_3 { + cpu-supply = <&buck2_reg>; +}; + +&ddrc { + operating-points-v2 = <&ddrc_opp_table>; + + ddrc_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-25M { + opp-hz = /bits/ 64 <25000000>; + }; + + opp-100M { + opp-hz = /bits/ 64 <100000000>; + }; + + opp-750M { + opp-hz = /bits/ 64 <750000000>;
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi line 75
Quoted 10 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +10
-0+ }; + }; +}; + +&ecspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + cs-gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>, + <&gpio1 0 GPIO_ACTIVE_HIGH>; + fsl,spi-num-chipselects = <2>;
This property is not supported any more.
Quoted 22 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +22
-0+ /delete-property/ dmas; + /delete-property/ dma-names; + status = "okay"; + + /* Resistive touch controller */ + touchscreen@0 { + reg = <0>; + compatible = "ti,ads7846"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_restouch>; + interrupt-parent = <&gpio1>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + + spi-max-frequency = <1500000>; + pendown-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; + + ti,x-min = /bits/ 16 <125>; + touchscreen-size-x = /bits/ 16 <4008>; + ti,y-min = /bits/ 16 <282>; + touchscreen-size-y = /bits/ 16 <3864>; + ti,x-plate-ohms = /bits/ 16 <180>; + touchscreen-max-pressure = /bits/ 16 <255>;
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi line 107
Quoted 10 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +10
-0+ touchscreen-average-samples = /bits/ 16 <10>; + ti,debounce-tol = /bits/ 16 <3>; + ti,debounce-rep = /bits/ 16 <1>; + ti,settle-delay-usec = /bits/ 16 <150>; + ti,keep-vref-on; + wakeup-source; + }; + + can: can@1 { + /* TODO: binding not documented, patches on the LKML */
Do not submit stuff that haven't landed.
Quoted 9 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +9
-0+ compatible = "microchip,mcp2517fd"; + reg = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can>; + interrupt-parent = <&gpio1>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + spi-max-frequency = <20000000>; + }; +};
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi line 126
Quoted 10 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +10
-0+ +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii"; + phy-handle = <ðphy>; + phy-supply = <®_eth_phy>; + phy-reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + phy-reset-duration = <100>; + phy-reset-post-delay = <100>;
These properties are deprecated. Check out bindings/net/fsl-fec.txt.
Quoted 223 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +223
-0+ fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <4>; + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic@4b { + compatible = "rohm,bd71847"; + reg = <0x4b>; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio2>; + interrupts = <8 GPIO_ACTIVE_LOW>; + rohm,reset-snvs-powered; + + regulators { + buck1_reg: BUCK1 { + regulator-name = "BUCK1"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + }; + + buck2_reg: BUCK2 { + regulator-name = "BUCK2"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <1000000>; + rohm,dvs-idle-voltage = <900000>; + }; + + buck3_reg: BUCK3 { + regulator-name = "BUCK3"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + regulator-always-on; + }; + + buck4_reg: BUCK4 { + regulator-name = "BUCK4"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5_reg: BUCK5 { + regulator-name = "BUCK5"; + regulator-min-microvolt = <1605000>; + regulator-max-microvolt = <1995000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6_reg: BUCK6 { + regulator-name = "BUCK6"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: LDO1 { + regulator-name = "LDO1"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <1900000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "LDO2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "LDO3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "LDO4"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo5_reg: LDO5 { + regulator-compatible = "LDO5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo6_reg: LDO6 { + regulator-name = "LDO6"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + /* TODO: configure audio, as of now just put a placeholder */ + wm8904: codec@1a { + compatible = "wlf,wm8904"; + reg = <0x1a>; + status = "disabled"; + }; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +/* Bluetooth */ +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + assigned-clocks = <&clk IMX8MM_CLK_UART2>; + assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>; + uart-has-rtscts; + status = "okay"; +}; + +/* Console */ +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbotg1 { + dr_mode = "otg"; + usb-role-switch; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "otg"; + usb-role-switch; + status = "okay"; +}; + +/* WIFI */ +&usdhc1 { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + bus-width = <4>; + non-removable; + keep-power-in-suspend; + status = "okay"; + + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +/* SD */ +&usdhc2 { + assigned-clocks = <&clk IMX8MM_CLK_USDHC2>; + assigned-clock-rates = <200000000>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + cd-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <®_usdhc2_vmmc>; + status = "okay"; +}; + +/* eMMC */ +&usdhc3 { + assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>; + assigned-clock-rates = <400000000>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +};
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi line 359
Quoted 10 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +10
-0+ +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default";
The property 'pinctrl-names' should be used with pinctrl-X as pair.
Shawn
Quoted 223 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +220
-0+ + pinctrl_can: cangrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x16 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x13 + MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x13 + MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x13 + MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x13 + MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x13 + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 + >; + }; + + pinctrl_pcie0: pcie0grp { + fsl,pins = < + MX8MM_IOMUXC_SAI2_RXFS_GPIO4_IO21 0x41 + >; + }; + + pinctrl_pmic: pmicirq { + fsl,pins = < + MX8MM_IOMUXC_SD1_DATA6_GPIO2_IO8 0x41 + >; + }; + + pinctrl_reg_eth_phy: regethphygrp { + fsl,pins = < + MX8MM_IOMUXC_SD1_DATA7_GPIO2_IO9 0x41 + >; + }; + + pinctrl_restouch: restouchgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x1c0 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x140 + MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x140 + MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x140 + MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x140 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140 + MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1grp100mhz { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1grp200mhz { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2grpgpio { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0xc1 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3grp100mhz { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3grp200mhz { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + >; + }; +};Signature · 1 line
2.17.1
Re: [PATCH v2 3/4] arm64: dts: imx8mm-var-som: Add Variscite VAR-SOM-MX8MM System on Module
Quoted 97 lines · Shawn Guo
Quoted 96 lines · Krzysztof Kozlowski
Add DTSI of Variscite VAR-SOM-MX8MM System on Module in a basic version, delivered with Variscite Symphony Evaluation kit. This version comes with:
- 2 GB of RAM,
- 16 GB eMMC,
- Gigabit Ethernet PHY,
- 802.11 ac/a/b/g/n WiFi with 4.2 Bluetooth (Cypress CYW43353),
- CAN bus,
- Audio codec (not yet configured in DTSI).Signed-off-by Krzysztof Kozlowski <[email protected]>---
Changes since v1:
1. None--- .../boot/dts/freescale/imx8mm-var-som.dtsi | 579 ++++++++++++++++++ 1 file changed, 579 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsiarch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +69
-0@@ -0,0 +1,579 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2019 NXP + * Copyright (C) 2020 Krzysztof Kozlowski <[email protected]> + */ + +#include "imx8mm.dtsi" + +/ { + model = "Variscite VAR-SOM-MX8MM module"; + compatible = "variscite,var-som-mx8mm", "fsl,imx8mm"; + + chosen { + stdout-path = &uart4; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0x0 0x40000000 0 0x80000000>; + }; + + reg_eth_phy: regulator-0 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_eth_phy>; + regulator-name = "eth_phy_pwr"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&A53_0 { + cpu-supply = <&buck2_reg>; +}; + +&A53_1 { + cpu-supply = <&buck2_reg>; +}; + +&A53_2 { + cpu-supply = <&buck2_reg>; +}; + +&A53_3 { + cpu-supply = <&buck2_reg>; +}; + +&ddrc { + operating-points-v2 = <&ddrc_opp_table>; + + ddrc_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-25M { + opp-hz = /bits/ 64 <25000000>; + }; + + opp-100M { + opp-hz = /bits/ 64 <100000000>; + }; + + opp-750M { + opp-hz = /bits/ 64 <750000000>; + }; + }; +}; +
Quoted 8 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi line 75
Quoted 6 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +6
-0+&ecspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + cs-gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>, + <&gpio1 0 GPIO_ACTIVE_HIGH>; + fsl,spi-num-chipselects = <2>;This property is not supported any more.
Sure.
Quoted 27 lines
Quoted 27 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +26
-0+ /delete-property/ dmas; + /delete-property/ dma-names; + status = "okay"; + + /* Resistive touch controller */ + touchscreen@0 { + reg = <0>; + compatible = "ti,ads7846"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_restouch>; + interrupt-parent = <&gpio1>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + + spi-max-frequency = <1500000>; + pendown-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; + + ti,x-min = /bits/ 16 <125>; + touchscreen-size-x = /bits/ 16 <4008>; + ti,y-min = /bits/ 16 <282>; + touchscreen-size-y = /bits/ 16 <3864>; + ti,x-plate-ohms = /bits/ 16 <180>; + touchscreen-max-pressure = /bits/ 16 <255>; + touchscreen-average-samples = /bits/ 16 <10>; + ti,debounce-tol = /bits/ 16 <3>; + ti,debounce-rep = /bits/ 16 <1>; + ti,settle-delay-usec = /bits/ 16 <150>;
Quoted 8 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi line 107
Quoted 6 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +6
-0+ ti,keep-vref-on; + wakeup-source; + }; + + can: can@1 { + /* TODO: binding not documented, patches on the LKML */Do not submit stuff that haven't landed.
It is in the HW so for completeness of HW description it has a meaning. However if that's not desired, I can skip it.
Quoted 14 lines
Quoted 14 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +13
-0+ compatible = "microchip,mcp2517fd"; + reg = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can>; + interrupt-parent = <&gpio1>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + spi-max-frequency = <20000000>; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>;
Quoted 8 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi line 126
Quoted 6 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +6
-0+ phy-mode = "rgmii"; + phy-handle = <ðphy>; + phy-supply = <®_eth_phy>; + phy-reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + phy-reset-duration = <100>; + phy-reset-post-delay = <100>;These properties are deprecated. Check out
bindings/net/fsl-fec.txt.
OK
Quoted 228 lines
Quoted 228 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +227
-0+ fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <4>; + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic@4b { + compatible = "rohm,bd71847"; + reg = <0x4b>; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio2>; + interrupts = <8 GPIO_ACTIVE_LOW>; + rohm,reset-snvs-powered; + + regulators { + buck1_reg: BUCK1 { + regulator-name = "BUCK1"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + }; + + buck2_reg: BUCK2 { + regulator-name = "BUCK2"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <1000000>; + rohm,dvs-idle-voltage = <900000>; + }; + + buck3_reg: BUCK3 { + regulator-name = "BUCK3"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + regulator-always-on; + }; + + buck4_reg: BUCK4 { + regulator-name = "BUCK4"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5_reg: BUCK5 { + regulator-name = "BUCK5"; + regulator-min-microvolt = <1605000>; + regulator-max-microvolt = <1995000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6_reg: BUCK6 { + regulator-name = "BUCK6"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: LDO1 { + regulator-name = "LDO1"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <1900000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "LDO2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "LDO3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "LDO4"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo5_reg: LDO5 { + regulator-compatible = "LDO5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo6_reg: LDO6 { + regulator-name = "LDO6"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + /* TODO: configure audio, as of now just put a placeholder */ + wm8904: codec@1a { + compatible = "wlf,wm8904"; + reg = <0x1a>; + status = "disabled"; + }; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +/* Bluetooth */ +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + assigned-clocks = <&clk IMX8MM_CLK_UART2>; + assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>; + uart-has-rtscts; + status = "okay"; +}; + +/* Console */ +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbotg1 { + dr_mode = "otg"; + usb-role-switch; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "otg"; + usb-role-switch; + status = "okay"; +}; + +/* WIFI */ +&usdhc1 { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + bus-width = <4>; + non-removable; + keep-power-in-suspend; + status = "okay"; + + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +/* SD */ +&usdhc2 { + assigned-clocks = <&clk IMX8MM_CLK_USDHC2>; + assigned-clock-rates = <200000000>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + cd-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <®_usdhc2_vmmc>; + status = "okay"; +}; + +/* eMMC */ +&usdhc3 { + assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>; + assigned-clock-rates = <400000000>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>;
Quoted 8 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi line 359
Quoted 6 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi new file +6
-0+ fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default";The property 'pinctrl-names' should be used with pinctrl-X as pair.
Indeed, this does not make much sense. Thanks for the review.
Best regards,
Krzysztof
PATCH v2 4/4 arm64: dts: imx8mm-var-som-symphony: Add Variscite Symphony board with VAR-SOM-MX8MM
In reply to Krzysztof KozlowskiAdd a DTS for Variscite Symphony evaluation kit with VAR-SOM-MX8MM System on Module.
---
Changes since v1:
1. Remove duplicated "leds" node,
2. Fix heartbeat to active low,
3. Add nxp,ptn5150 extcon.
--- arch/arm64/boot/dts/freescale/Makefile | 1 + .../dts/freescale/imx8mm-var-som-symphony.dts | 248 ++++++++++++++++++ 2 files changed, 249 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
arch/arm64/boot/dts/freescale/Makefile +1 -0
@@ -29,6 +29,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts new file +248 -0
248 lines not on this page · raw message
Signature · 1 line
2.17.1
Re: [PATCH v2 4/4] arm64: dts: imx8mm-var-som-symphony: Add Variscite Symphony board with VAR-SOM-MX8MM
Quoted 39 lines · Krzysztof Kozlowski
Add a DTS for Variscite Symphony evaluation kit with VAR-SOM-MX8MM System on Module.
Signed-off-by Krzysztof Kozlowski <[email protected]>---
Changes since v1:
1. Remove duplicated "leds" node,
2. Fix heartbeat to active low,
3. Add nxp,ptn5150 extcon.--- arch/arm64/boot/dts/freescale/Makefile | 1 + .../dts/freescale/imx8mm-var-som-symphony.dts | 248 ++++++++++++++++++ 2 files changed, 249 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dtsarch/arm64/boot/dts/freescale/Makefile +1
-0@@ -29,6 +29,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtbarch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts new file +4
-0@@ -0,0 +1,248 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Krzysztof Kozlowski <[email protected]> + */
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts line 14
Quoted 10 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts new file +10
-0+ +/dts-v1/; + +#include "imx8mm-var-som.dtsi" + +/ { + model = "Variscite VAR-SOM-MX8MM Symphony evaluation board"; + compatible = "variscite,var-som-mx8mm-symphony", "variscite,var-som-mx8mm", "fsl,imx8mm"; + + reg_usdhc2_vmmc: regulator-1 {
regulator-usdhc2-vmmc
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts line 25
Quoted 11 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts new file +11
-0+ compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb_otg2_vbus: regulator-2 {
regulator-usb-otg2-vbus
Quoted 155 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts new file +155
-0+ compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb_otg2_vbus>; + regulator-name = "usb_otg2_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio5 1 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + gpio-keys { + compatible = "gpio-keys"; + + back { + label = "Back"; + gpios = <&pca9534 1 GPIO_ACTIVE_LOW>; + linux,code = <KEY_BACK>; + }; + + home { + label = "Home"; + gpios = <&pca9534 2 GPIO_ACTIVE_LOW>; + linux,code = <KEY_HOME>; + }; + + menu { + label = "Menu"; + gpios = <&pca9534 3 GPIO_ACTIVE_LOW>; + linux,code = <KEY_MENU>; + }; + }; + + leds { + compatible = "gpio-leds"; + + heartbeat { + label = "Heartbeat"; + gpios = <&pca9534 0 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +ðphy { + reset-gpios = <&pca9534 5 GPIO_ACTIVE_HIGH>; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pca9534: gpio@20 { + compatible = "nxp,pca9534"; + reg = <0x20>; + gpio-controller; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pca9534>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + #gpio-cells = <2>; + wakeup-source; + + /* USB 3.0 OTG (usbotg1) / SATA port switch, set to USB 3.0 */ + usb3-sata-sel-hog { + gpio-hog; + gpios = <4 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "usb3_sata_sel"; + }; + + som-vselect-hog { + gpio-hog; + gpios = <6 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "som_vselect"; + }; + + enet-sel-hog { + gpio-hog; + gpios = <7 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "enet_sel"; + }; + }; + + extcon_usbotg1: typec@3d { + compatible = "nxp,ptn5150"; + reg = <0x3d>; + int-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ptn5150>; + status = "okay"; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + /* Capacitive touch controller */ + ft5x06_ts: touchscreen@38 { + compatible = "edt,edt-ft5406"; + reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_captouch>; + interrupt-parent = <&gpio5>; + interrupts = <4 GPIO_ACTIVE_HIGH>; + + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-inverted-x; + touchscreen-inverted-y; + }; + + rtc@68 { + compatible = "dallas,ds1337"; + reg = <0x68>; + wakeup-source; + }; +}; + +/* Header */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +/* Header */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&usbotg1 { + disable-over-current; + extcon = <&extcon_usbotg1>, <&extcon_usbotg1>; +}; + +&usbotg2 { + dr_mode = "host"; + vbus-supply = <®_usb_otg2_vbus>; + srp-disable; + hnp-disable; + adp-disable; + disable-over-current; + /delete-property/ usb-role-switch; + /* + * FIXME: having USB2 enabled hangs the boot just after: + * [ 1.943365] ci_hdrc ci_hdrc.1: EHCI Host Controller
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts line 190
Quoted 10 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts new file +10
-0+ * [ 1.948287] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 + * [ 1.971006] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 + * [ 1.977203] hub 1-0:1.0: USB hub found + * [ 1.980987] hub 1-0:1.0: 1 port detected + */ + status = "disabled"; +}; + +&iomuxc { + pinctrl-names = "default";
Drop this.
Shawn
Quoted 61 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts new file +58
-0+ + pinctrl_captouch: captouchgrp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4 0x16 + >; + }; + + pinctrl_gpio_led: gpioledgrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 + >; + }; + + pinctrl_pca9534: pca9534grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x16 + >; + }; + + pinctrl_ptn5150: ptn5150grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x16 + >; + }; + + pinctrl_reg_usb_otg2_vbus: regusbotg2vbusgrp { + fsl,pins = < + MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1 0x16 + >; + }; + + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 + >; + }; +};Signature · 1 line
2.17.1
Re: [PATCH v2 4/4] arm64: dts: imx8mm-var-som-symphony: Add Variscite Symphony board with VAR-SOM-MX8MM
Quoted 44 lines · Shawn Guo
Quoted 43 lines · Krzysztof Kozlowski
Add a DTS for Variscite Symphony evaluation kit with VAR-SOM-MX8MM System on Module.
Signed-off-by Krzysztof Kozlowski <[email protected]>---
Changes since v1:
1. Remove duplicated "leds" node,
2. Fix heartbeat to active low,
3. Add nxp,ptn5150 extcon.--- arch/arm64/boot/dts/freescale/Makefile | 1 + .../dts/freescale/imx8mm-var-som-symphony.dts | 248 ++++++++++++++++++ 2 files changed, 249 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dtsarch/arm64/boot/dts/freescale/Makefile +1
-0@@ -29,6 +29,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtbarch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts new file +8
-0@@ -0,0 +1,248 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Krzysztof Kozlowski <[email protected]> + */ + +/dts-v1/; + +#include "imx8mm-var-som.dtsi"
Quoted 8 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts line 14
Quoted 6 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts new file +6
-0+ +/ { + model = "Variscite VAR-SOM-MX8MM Symphony evaluation board"; + compatible = "variscite,var-som-mx8mm-symphony", "variscite,var-som-mx8mm", "fsl,imx8mm"; + + reg_usdhc2_vmmc: regulator-1 {regulator-usdhc2-vmmc
You mean the node name? If so, it's not correct with device tree specification:
"The node-name (...) should describe the general class of device.:
If appropriate, the name should be one of the following choices:
(...)
- regulator"
Adding specific function/type/usage to the name of the node is a opposite choice to "general class".
Quoted 174 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts line 25
Quoted 12 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts new file +11
-0+ compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb_otg2_vbus: regulator-2 {regulator-usb-otg2-vbus
Quoted 159 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts new file +159
-0+ compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb_otg2_vbus>; + regulator-name = "usb_otg2_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio5 1 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + gpio-keys { + compatible = "gpio-keys"; + + back { + label = "Back"; + gpios = <&pca9534 1 GPIO_ACTIVE_LOW>; + linux,code = <KEY_BACK>; + }; + + home { + label = "Home"; + gpios = <&pca9534 2 GPIO_ACTIVE_LOW>; + linux,code = <KEY_HOME>; + }; + + menu { + label = "Menu"; + gpios = <&pca9534 3 GPIO_ACTIVE_LOW>; + linux,code = <KEY_MENU>; + }; + }; + + leds { + compatible = "gpio-leds"; + + heartbeat { + label = "Heartbeat"; + gpios = <&pca9534 0 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +ðphy { + reset-gpios = <&pca9534 5 GPIO_ACTIVE_HIGH>; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pca9534: gpio@20 { + compatible = "nxp,pca9534"; + reg = <0x20>; + gpio-controller; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pca9534>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + #gpio-cells = <2>; + wakeup-source; + + /* USB 3.0 OTG (usbotg1) / SATA port switch, set to USB 3.0 */ + usb3-sata-sel-hog { + gpio-hog; + gpios = <4 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "usb3_sata_sel"; + }; + + som-vselect-hog { + gpio-hog; + gpios = <6 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "som_vselect"; + }; + + enet-sel-hog { + gpio-hog; + gpios = <7 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "enet_sel"; + }; + }; + + extcon_usbotg1: typec@3d { + compatible = "nxp,ptn5150"; + reg = <0x3d>; + int-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ptn5150>; + status = "okay"; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + /* Capacitive touch controller */ + ft5x06_ts: touchscreen@38 { + compatible = "edt,edt-ft5406"; + reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_captouch>; + interrupt-parent = <&gpio5>; + interrupts = <4 GPIO_ACTIVE_HIGH>; + + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-inverted-x; + touchscreen-inverted-y; + }; + + rtc@68 { + compatible = "dallas,ds1337"; + reg = <0x68>; + wakeup-source; + }; +}; + +/* Header */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +/* Header */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&usbotg1 { + disable-over-current; + extcon = <&extcon_usbotg1>, <&extcon_usbotg1>; +}; + +&usbotg2 { + dr_mode = "host"; + vbus-supply = <®_usb_otg2_vbus>; + srp-disable; + hnp-disable; + adp-disable; + disable-over-current; + /delete-property/ usb-role-switch; + /* + * FIXME: having USB2 enabled hangs the boot just after: + * [ 1.943365] ci_hdrc ci_hdrc.1: EHCI Host Controller + * [ 1.948287] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 + * [ 1.971006] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 + * [ 1.977203] hub 1-0:1.0: USB hub found + * [ 1.980987] hub 1-0:1.0: 1 port detected
Quoted 8 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts line 190
Quoted 6 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts new file +6
-0+ */ + status = "disabled"; +}; + +&iomuxc { + pinctrl-names = "default";Drop this.
Indeed, thanks.
Best regards,
Krzysztof
Re: [PATCH v2 4/4] arm64: dts: imx8mm-var-som-symphony: Add Variscite Symphony board with VAR-SOM-MX8MM
Quoted 61 lines · Krzysztof Kozlowski
Quoted 44 lines · Shawn Guo
Quoted 43 lines · Krzysztof Kozlowski
Add a DTS for Variscite Symphony evaluation kit with VAR-SOM-MX8MM System on Module.
Signed-off-by Krzysztof Kozlowski <[email protected]>---
Changes since v1:
1. Remove duplicated "leds" node,
2. Fix heartbeat to active low,
3. Add nxp,ptn5150 extcon.--- arch/arm64/boot/dts/freescale/Makefile | 1 + .../dts/freescale/imx8mm-var-som-symphony.dts | 248 ++++++++++++++++++ 2 files changed, 249 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dtsarch/arm64/boot/dts/freescale/Makefile +1
-0@@ -29,6 +29,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtbarch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts new file +8
-0@@ -0,0 +1,248 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Krzysztof Kozlowski <[email protected]> + */ + +/dts-v1/; + +#include "imx8mm-var-som.dtsi"Quoted 8 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts line 14
Quoted 6 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts new file +6
-0+ +/ { + model = "Variscite VAR-SOM-MX8MM Symphony evaluation board"; + compatible = "variscite,var-som-mx8mm-symphony", "variscite,var-som-mx8mm", "fsl,imx8mm"; + + reg_usdhc2_vmmc: regulator-1 {regulator-usdhc2-vmmc
You mean the node name? If so, it's not correct with device tree specification:
"The node-name (...) should describe the general class of device.:
If appropriate, the name should be one of the following choices:
(...)
- regulator"
Quoted 2 lines
Adding specific function/type/usage to the name of the node is a opposite choice to "general class".
Well, the node is named in general class, i.e. regulator-xxx, and we would like the suffix to be a bit more specific. We have been using this name schema for fixed-regulator on i.MX platforms for long time.
Shawn
Re: [PATCH v2 4/4] arm64: dts: imx8mm-var-som-symphony: Add Variscite Symphony board with VAR-SOM-MX8MM
Quoted 62 lines · Shawn Guo
Quoted 61 lines · Krzysztof Kozlowski
Quoted 44 lines · Shawn Guo
Quoted 43 lines · Krzysztof Kozlowski
Add a DTS for Variscite Symphony evaluation kit with VAR-SOM-MX8MM System on Module.
Signed-off-by Krzysztof Kozlowski <[email protected]>---
Changes since v1:
1. Remove duplicated "leds" node,
2. Fix heartbeat to active low,
3. Add nxp,ptn5150 extcon.--- arch/arm64/boot/dts/freescale/Makefile | 1 + .../dts/freescale/imx8mm-var-som-symphony.dts | 248 ++++++++++++++++++ 2 files changed, 249 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dtsarch/arm64/boot/dts/freescale/Makefile +1
-0@@ -29,6 +29,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtbarch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts new file +8
-0@@ -0,0 +1,248 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Krzysztof Kozlowski <[email protected]> + */ + +/dts-v1/; + +#include "imx8mm-var-som.dtsi"Quoted 8 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts line 14
Quoted 6 lines
arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts new file +6
-0+ +/ { + model = "Variscite VAR-SOM-MX8MM Symphony evaluation board"; + compatible = "variscite,var-som-mx8mm-symphony", "variscite,var-som-mx8mm", "fsl,imx8mm"; + + reg_usdhc2_vmmc: regulator-1 {regulator-usdhc2-vmmc
You mean the node name? If so, it's not correct with device tree specification:
"The node-name (...) should describe the general class of device.:
If appropriate, the name should be one of the following choices:
(...)
- regulator"
Quoted 6 lines
Quoted 2 lines
Adding specific function/type/usage to the name of the node is a opposite choice to "general class".
Well, the node is named in general class, i.e. regulator-xxx, and we would like the suffix to be a bit more specific. We have been using this name schema for fixed-regulator on i.MX platforms for long time.
Name "regulator-usdhc2-vmmc" is not general, it is specific. The DT specification gives the example of generic name and it is "regulator".
It is the same with CPU nodes having names "cpu@0", not "cpu-a53@0" or whatever other suffix. It is the same reason why I2C is "i2c@12345678", not "i2c_1@" or "i2c_for_abcd".
The suffix is not needed as Linux does not use it (instead uses regulator-name which is specific). Humans on the other hand can understand the specifics from the label and from the regulator name. Therefore they also do not need the suffix.
I know that other i.MX DTSes follow this pattern but it is still not the recommended one. It's a pattern which should be replaced.
Anyway, if the names of regulators stop this patch from being applied, I will change them to expected.
Best regards,
Krzysztof