Skip to contentSkip to conversation

arm64: dts: ls1088a: add more thermal zone support

PATCH Applied [email protected] 3 participants 6 messages Jul 15, 2020 – Aug 22, 2020

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/2 arm64: dts: ls1088a: add more thermal zone support

From: Yuantian Tang <[email protected]>

There are 2 thermal zones in ls1088a soc. Add the other thermal zone node to enable it.
Also update the values in calibration table to make the temperatures monitored more precise.

---
v2:
- remove useless alert trip

 .../arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 94 +++++++++++--------
 1 file changed, 56 insertions(+), 38 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi +56 -38
index 169f4742ae3b..b961a896ede7 100644
@@ -130,19 +130,19 @@
 	};
 
 	thermal-zones {
-		cpu_thermal: cpu-thermal {
+		core-cluster {
 			polling-delay-passive = <1000>;
 			polling-delay = <5000>;
 			thermal-sensors = <&tmu 0>;
 
 			trips {
-				cpu_alert: cpu-alert {
+				core_cluster_alert: core-cluster-alert {
 					temperature = <85000>;
 					hysteresis = <2000>;
 					type = "passive";
 				};
 
-				cpu_crit: cpu-crit {
+				core-cluster-crit {
 					temperature = <95000>;
 					hysteresis = <2000>;
 					type = "critical";
@@ -151,7 +151,7 @@
 
 			cooling-maps {
 				map0 {
-					trip = <&cpu_alert>;
+					trip = <&core_cluster_alert>;
 					cooling-device =
 						<&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
 						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
@@ -164,6 +164,20 @@
 				};
 			};
 		};
+
+		soc {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+			thermal-sensors = <&tmu 1>;
+
+			trips {
+				soc-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
 	};
 
 	timer {
@@ -210,45 +224,49 @@
 			compatible = "fsl,qoriq-tmu";
 			reg = <0x0 0x1f80000 0x0 0x10000>;
 			interrupts = <0 23 0x4>;
-			fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>;
+			fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x70062>;
 			fsl,tmu-calibration =
 				/* Calibration data group 1 */
-				<0x00000000 0x00000026
-				0x00000001 0x0000002d
-				0x00000002 0x00000032
-				0x00000003 0x00000039
-				0x00000004 0x0000003f
-				0x00000005 0x00000046
-				0x00000006 0x0000004d
-				0x00000007 0x00000054
-				0x00000008 0x0000005a
-				0x00000009 0x00000061
-				0x0000000a 0x0000006a
-				0x0000000b 0x00000071
+				<0x00000000 0x00000023
+				0x00000001 0x0000002a
+				0x00000002 0x00000030
+				0x00000003 0x00000037
+				0x00000004 0x0000003d
+				0x00000005 0x00000044
+				0x00000006 0x0000004a
+				0x00000007 0x00000051
+				0x00000008 0x00000057
+				0x00000009 0x0000005e
+				0x0000000a 0x00000064
+				0x0000000b 0x0000006b
 				/* Calibration data group 2 */
-				0x00010000 0x00000025
-				0x00010001 0x0000002c
-				0x00010002 0x00000035
-				0x00010003 0x0000003d
-				0x00010004 0x00000045
-				0x00010005 0x0000004e
-				0x00010006 0x00000057
-				0x00010007 0x00000061
-				0x00010008 0x0000006b
-				0x00010009 0x00000076
+				0x00010000 0x00000022
+				0x00010001 0x0000002a
+				0x00010002 0x00000032
+				0x00010003 0x0000003a
+				0x00010004 0x00000042
+				0x00010005 0x0000004a
+				0x00010006 0x00000052
+				0x00010007 0x0000005a
+				0x00010008 0x00000062
+				0x00010009 0x0000006a
 				/* Calibration data group 3 */
-				0x00020000 0x00000029
-				0x00020001 0x00000033
-				0x00020002 0x0000003d
-				0x00020003 0x00000049
-				0x00020004 0x00000056
-				0x00020005 0x00000061
-				0x00020006 0x0000006d
+				0x00020000 0x00000021
+				0x00020001 0x0000002b
+				0x00020002 0x00000035
+				0x00020003 0x00000040
+				0x00020004 0x0000004a
+				0x00020005 0x00000054
+				0x00020006 0x0000005e
 				/* Calibration data group 4 */
-				0x00030000 0x00000021
-				0x00030001 0x0000002a
-				0x00030002 0x0000003c
-				0x00030003 0x0000004e>;
+				0x00030000 0x00000010
+				0x00030001 0x0000001c
+				0x00030002 0x00000027
+				0x00030003 0x00000032
+				0x00030004 0x0000003e
+				0x00030005 0x00000049
+				0x00030006 0x00000054
+				0x00030007 0x00000060>;
 			little-endian;
 			#thermal-sensor-cells = <1>;
 		};
Signature · 1 line
2.17.1
#1 lore raw

PATCH v2 2/2 arm64: dts: ls208xa: add more thermal zone support

From: Yuantian Tang <[email protected]>

There are 7 thermal zones in ls208xa soc. Add the other thermal zone nodes to enable them.

---
v2:
- remove useless alert trip
- add cooling-map to core cluster zones.

 .../arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 141 ++++++++++++++++--
 1 file changed, 132 insertions(+), 9 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi +132 -9
index 41102dacc2e1..cc36c969dd9d 100644
@@ -79,20 +79,62 @@
 	};
 
 	thermal-zones {
-		cpu_thermal: cpu-thermal {
+		ddr-controller1 {
 			polling-delay-passive = <1000>;
 			polling-delay = <5000>;
+			thermal-sensors = <&tmu 1>;
 
+			trips {
+				ddr-ctrler1-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		ddr-controller2 {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+			thermal-sensors = <&tmu 2>;
+
+			trips {
+				ddr-ctrler2-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		ddr-controller3 {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+			thermal-sensors = <&tmu 3>;
+
+			trips {
+				ddr-ctrler3-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		core-cluster1 {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
 			thermal-sensors = <&tmu 4>;
 
 			trips {
-				cpu_alert: cpu-alert {
-					temperature = <75000>;
+				core_cluster1_alert: core-cluster1-alert {
+					temperature = <85000>;
 					hysteresis = <2000>;
 					type = "passive";
 				};
-				cpu_crit: cpu-crit {
-					temperature = <85000>;
+
+				core-cluster1-crit {
+					temperature = <95000>;
 					hysteresis = <2000>;
 					type = "critical";
 				};
@@ -100,14 +142,95 @@
 
 			cooling-maps {
 				map0 {
-					trip = <&cpu_alert>;
+					trip = <&core_cluster1_alert>;
 					cooling-device =
 						<&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		core-cluster2 {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+			thermal-sensors = <&tmu 5>;
+
+			trips {
+				core_cluster2_alert: core-cluster2-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				core-cluster2-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&core_cluster2_alert>;
+					cooling-device =
 						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		core-cluster3 {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+			thermal-sensors = <&tmu 6>;
+
+			trips {
+				core_cluster3_alert: core-cluster3-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				core-cluster3-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&core_cluster3_alert>;
+					cooling-device =
 						<&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-						<&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		core-cluster4 {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+			thermal-sensors = <&tmu 7>;
+
+			trips {
+				core_cluster4_alert: core-cluster4-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				core-cluster4-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&core_cluster4_alert>;
+					cooling-device =
 						<&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
 						<&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
 				};
Signature · 1 line
2.17.1
Reviewed-by on v2 2/2
#2 lore raw

Re: [PATCH 2/2 v2] arm64: dts: ls208xa: add more thermal zone support

Quoted 7 lines · On Wed, Jul 15, 2020 at 12:25 PM <[email protected]> wrote:

From: Yuantian Tang <[email protected]>

There are 7 thermal zones in ls208xa soc. Add the other thermal zone nodes to enable them.

Quoted 183 lines

---
v2:
- remove useless alert trip
- add cooling-map to core cluster zones.

 .../arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 141 ++++++++++++++++--
 1 file changed, 132 insertions(+), 9 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi +132 -10
index 41102dacc2e1..cc36c969dd9d 100644
@@ -79,20 +79,62 @@
        };
 
        thermal-zones {
-               cpu_thermal: cpu-thermal {
+               ddr-controller1 {
                        polling-delay-passive = <1000>;
                        polling-delay = <5000>;
+                       thermal-sensors = <&tmu 1>;
 
+                       trips {
+                               ddr-ctrler1-crit {
+                                       temperature = <95000>;
+                                       hysteresis = <2000>;
+                                       type = "critical";
+                               };
+                       };
+               };
+
+               ddr-controller2 {
+                       polling-delay-passive = <1000>;
+                       polling-delay = <5000>;
+                       thermal-sensors = <&tmu 2>;
+
+                       trips {
+                               ddr-ctrler2-crit {
+                                       temperature = <95000>;
+                                       hysteresis = <2000>;
+                                       type = "critical";
+                               };
+                       };
+               };
+
+               ddr-controller3 {
+                       polling-delay-passive = <1000>;
+                       polling-delay = <5000>;
+                       thermal-sensors = <&tmu 3>;
+
+                       trips {
+                               ddr-ctrler3-crit {
+                                       temperature = <95000>;
+                                       hysteresis = <2000>;
+                                       type = "critical";
+                               };
+                       };
+               };
+
+               core-cluster1 {
+                       polling-delay-passive = <1000>;
+                       polling-delay = <5000>;
                        thermal-sensors = <&tmu 4>;
 
                        trips {
-                               cpu_alert: cpu-alert {
-                                       temperature = <75000>;
+                               core_cluster1_alert: core-cluster1-alert {
+                                       temperature = <85000>;
                                        hysteresis = <2000>;
                                        type = "passive";
                                };
-                               cpu_crit: cpu-crit {
-                                       temperature = <85000>;
+
+                               core-cluster1-crit {
+                                       temperature = <95000>;
                                        hysteresis = <2000>;
                                        type = "critical";
                                };
@@ -100,14 +142,95 @@
 
                        cooling-maps {
                                map0 {
-                                       trip = <&cpu_alert>;
+                                       trip = <&core_cluster1_alert>;
                                        cooling-device =
                                                <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-                                               <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                               <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+                               };
+                       };
+               };
+
+               core-cluster2 {
+                       polling-delay-passive = <1000>;
+                       polling-delay = <5000>;
+                       thermal-sensors = <&tmu 5>;
+
+                       trips {
+                               core_cluster2_alert: core-cluster2-alert {
+                                       temperature = <85000>;
+                                       hysteresis = <2000>;
+                                       type = "passive";
+                               };
+
+                               core-cluster2-crit {
+                                       temperature = <95000>;
+                                       hysteresis = <2000>;
+                                       type = "critical";
+                               };
+                       };
+
+                       cooling-maps {
+                               map0 {
+                                       trip = <&core_cluster2_alert>;
+                                       cooling-device =
                                                <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-                                               <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                               <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+                               };
+                       };
+               };
+
+               core-cluster3 {
+                       polling-delay-passive = <1000>;
+                       polling-delay = <5000>;
+                       thermal-sensors = <&tmu 6>;
+
+                       trips {
+                               core_cluster3_alert: core-cluster3-alert {
+                                       temperature = <85000>;
+                                       hysteresis = <2000>;
+                                       type = "passive";
+                               };
+
+                               core-cluster3-crit {
+                                       temperature = <95000>;
+                                       hysteresis = <2000>;
+                                       type = "critical";
+                               };
+                       };
+
+                       cooling-maps {
+                               map0 {
+                                       trip = <&core_cluster3_alert>;
+                                       cooling-device =
                                                <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-                                               <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                               <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+                               };
+                       };
+               };
+
+               core-cluster4 {
+                       polling-delay-passive = <1000>;
+                       polling-delay = <5000>;
+                       thermal-sensors = <&tmu 7>;
+
+                       trips {
+                               core_cluster4_alert: core-cluster4-alert {
+                                       temperature = <85000>;
+                                       hysteresis = <2000>;
+                                       type = "passive";
+                               };
+
+                               core-cluster4-crit {
+                                       temperature = <95000>;
+                                       hysteresis = <2000>;
+                                       type = "critical";
+                               };
+                       };
+
+                       cooling-maps {
+                               map0 {
+                                       trip = <&core_cluster4_alert>;
+                                       cooling-device =
                                                <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
                                                <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
                                };
--

2.17.1

#3 lore raw
In reply to [email protected]
Quoted 11 lines · On Wed, Jul 15, 2020 at 02:49:08PM +0800, [email protected] wrote:

From: Yuantian Tang <[email protected]>

There are 2 thermal zones in ls1088a soc. Add the other thermal zone node to enable it.
Also update the values in calibration table to make the temperatures monitored more precise.

---
v2:
- remove useless alert trip

@Amit, looks good to you?

Shawn

Quoted 148 lines
 .../arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 94 +++++++++++--------
 1 file changed, 56 insertions(+), 38 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi +56 -38
index 169f4742ae3b..b961a896ede7 100644
@@ -130,19 +130,19 @@
 	};
 
 	thermal-zones {
-		cpu_thermal: cpu-thermal {
+		core-cluster {
 			polling-delay-passive = <1000>;
 			polling-delay = <5000>;
 			thermal-sensors = <&tmu 0>;
 
 			trips {
-				cpu_alert: cpu-alert {
+				core_cluster_alert: core-cluster-alert {
 					temperature = <85000>;
 					hysteresis = <2000>;
 					type = "passive";
 				};
 
-				cpu_crit: cpu-crit {
+				core-cluster-crit {
 					temperature = <95000>;
 					hysteresis = <2000>;
 					type = "critical";
@@ -151,7 +151,7 @@
 
 			cooling-maps {
 				map0 {
-					trip = <&cpu_alert>;
+					trip = <&core_cluster_alert>;
 					cooling-device =
 						<&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
 						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
@@ -164,6 +164,20 @@
 				};
 			};
 		};
+
+		soc {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+			thermal-sensors = <&tmu 1>;
+
+			trips {
+				soc-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
 	};
 
 	timer {
@@ -210,45 +224,49 @@
 			compatible = "fsl,qoriq-tmu";
 			reg = <0x0 0x1f80000 0x0 0x10000>;
 			interrupts = <0 23 0x4>;
-			fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>;
+			fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x70062>;
 			fsl,tmu-calibration =
 				/* Calibration data group 1 */
-				<0x00000000 0x00000026
-				0x00000001 0x0000002d
-				0x00000002 0x00000032
-				0x00000003 0x00000039
-				0x00000004 0x0000003f
-				0x00000005 0x00000046
-				0x00000006 0x0000004d
-				0x00000007 0x00000054
-				0x00000008 0x0000005a
-				0x00000009 0x00000061
-				0x0000000a 0x0000006a
-				0x0000000b 0x00000071
+				<0x00000000 0x00000023
+				0x00000001 0x0000002a
+				0x00000002 0x00000030
+				0x00000003 0x00000037
+				0x00000004 0x0000003d
+				0x00000005 0x00000044
+				0x00000006 0x0000004a
+				0x00000007 0x00000051
+				0x00000008 0x00000057
+				0x00000009 0x0000005e
+				0x0000000a 0x00000064
+				0x0000000b 0x0000006b
 				/* Calibration data group 2 */
-				0x00010000 0x00000025
-				0x00010001 0x0000002c
-				0x00010002 0x00000035
-				0x00010003 0x0000003d
-				0x00010004 0x00000045
-				0x00010005 0x0000004e
-				0x00010006 0x00000057
-				0x00010007 0x00000061
-				0x00010008 0x0000006b
-				0x00010009 0x00000076
+				0x00010000 0x00000022
+				0x00010001 0x0000002a
+				0x00010002 0x00000032
+				0x00010003 0x0000003a
+				0x00010004 0x00000042
+				0x00010005 0x0000004a
+				0x00010006 0x00000052
+				0x00010007 0x0000005a
+				0x00010008 0x00000062
+				0x00010009 0x0000006a
 				/* Calibration data group 3 */
-				0x00020000 0x00000029
-				0x00020001 0x00000033
-				0x00020002 0x0000003d
-				0x00020003 0x00000049
-				0x00020004 0x00000056
-				0x00020005 0x00000061
-				0x00020006 0x0000006d
+				0x00020000 0x00000021
+				0x00020001 0x0000002b
+				0x00020002 0x00000035
+				0x00020003 0x00000040
+				0x00020004 0x0000004a
+				0x00020005 0x00000054
+				0x00020006 0x0000005e
 				/* Calibration data group 4 */
-				0x00030000 0x00000021
-				0x00030001 0x0000002a
-				0x00030002 0x0000003c
-				0x00030003 0x0000004e>;
+				0x00030000 0x00000010
+				0x00030001 0x0000001c
+				0x00030002 0x00000027
+				0x00030003 0x00000032
+				0x00030004 0x0000003e
+				0x00030005 0x00000049
+				0x00030006 0x00000054
+				0x00030007 0x00000060>;
 			little-endian;
 			#thermal-sensor-cells = <1>;
 		};
Signature · 1 line
2.17.1
Reviewed-by on v2 1/2
#4 lore raw
In reply to [email protected]
Quoted 9 lines · On Wed, Jul 15, 2020 at 12:25 PM <[email protected]> wrote:

From: Yuantian Tang <[email protected]>

There are 2 thermal zones in ls1088a soc. Add the other thermal zone node to enable it.
Also update the values in calibration table to make the temperatures monitored more precise.

Quoted 151 lines

---
v2:
- remove useless alert trip

 .../arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 94 +++++++++++--------
 1 file changed, 56 insertions(+), 38 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi +56 -39
index 169f4742ae3b..b961a896ede7 100644
@@ -130,19 +130,19 @@
        };
 
        thermal-zones {
-               cpu_thermal: cpu-thermal {
+               core-cluster {
                        polling-delay-passive = <1000>;
                        polling-delay = <5000>;
                        thermal-sensors = <&tmu 0>;
 
                        trips {
-                               cpu_alert: cpu-alert {
+                               core_cluster_alert: core-cluster-alert {
                                        temperature = <85000>;
                                        hysteresis = <2000>;
                                        type = "passive";
                                };
 
-                               cpu_crit: cpu-crit {
+                               core-cluster-crit {
                                        temperature = <95000>;
                                        hysteresis = <2000>;
                                        type = "critical";
@@ -151,7 +151,7 @@
 
                        cooling-maps {
                                map0 {
-                                       trip = <&cpu_alert>;
+                                       trip = <&core_cluster_alert>;
                                        cooling-device =
                                                <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
                                                <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
@@ -164,6 +164,20 @@
                                };
                        };
                };
+
+               soc {
+                       polling-delay-passive = <1000>;
+                       polling-delay = <5000>;
+                       thermal-sensors = <&tmu 1>;
+
+                       trips {
+                               soc-crit {
+                                       temperature = <95000>;
+                                       hysteresis = <2000>;
+                                       type = "critical";
+                               };
+                       };
+               };
        };
 
        timer {
@@ -210,45 +224,49 @@
                        compatible = "fsl,qoriq-tmu";
                        reg = <0x0 0x1f80000 0x0 0x10000>;
                        interrupts = <0 23 0x4>;
-                       fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>;
+                       fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x70062>;
                        fsl,tmu-calibration =
                                /* Calibration data group 1 */
-                               <0x00000000 0x00000026
-                               0x00000001 0x0000002d
-                               0x00000002 0x00000032
-                               0x00000003 0x00000039
-                               0x00000004 0x0000003f
-                               0x00000005 0x00000046
-                               0x00000006 0x0000004d
-                               0x00000007 0x00000054
-                               0x00000008 0x0000005a
-                               0x00000009 0x00000061
-                               0x0000000a 0x0000006a
-                               0x0000000b 0x00000071
+                               <0x00000000 0x00000023
+                               0x00000001 0x0000002a
+                               0x00000002 0x00000030
+                               0x00000003 0x00000037
+                               0x00000004 0x0000003d
+                               0x00000005 0x00000044
+                               0x00000006 0x0000004a
+                               0x00000007 0x00000051
+                               0x00000008 0x00000057
+                               0x00000009 0x0000005e
+                               0x0000000a 0x00000064
+                               0x0000000b 0x0000006b
                                /* Calibration data group 2 */
-                               0x00010000 0x00000025
-                               0x00010001 0x0000002c
-                               0x00010002 0x00000035
-                               0x00010003 0x0000003d
-                               0x00010004 0x00000045
-                               0x00010005 0x0000004e
-                               0x00010006 0x00000057
-                               0x00010007 0x00000061
-                               0x00010008 0x0000006b
-                               0x00010009 0x00000076
+                               0x00010000 0x00000022
+                               0x00010001 0x0000002a
+                               0x00010002 0x00000032
+                               0x00010003 0x0000003a
+                               0x00010004 0x00000042
+                               0x00010005 0x0000004a
+                               0x00010006 0x00000052
+                               0x00010007 0x0000005a
+                               0x00010008 0x00000062
+                               0x00010009 0x0000006a
                                /* Calibration data group 3 */
-                               0x00020000 0x00000029
-                               0x00020001 0x00000033
-                               0x00020002 0x0000003d
-                               0x00020003 0x00000049
-                               0x00020004 0x00000056
-                               0x00020005 0x00000061
-                               0x00020006 0x0000006d
+                               0x00020000 0x00000021
+                               0x00020001 0x0000002b
+                               0x00020002 0x00000035
+                               0x00020003 0x00000040
+                               0x00020004 0x0000004a
+                               0x00020005 0x00000054
+                               0x00020006 0x0000005e
                                /* Calibration data group 4 */
-                               0x00030000 0x00000021
-                               0x00030001 0x0000002a
-                               0x00030002 0x0000003c
-                               0x00030003 0x0000004e>;
+                               0x00030000 0x00000010
+                               0x00030001 0x0000001c
+                               0x00030002 0x00000027
+                               0x00030003 0x00000032
+                               0x00030004 0x0000003e
+                               0x00030005 0x00000049
+                               0x00030006 0x00000054
+                               0x00030007 0x00000060>;
                        little-endian;
                        #thermal-sensor-cells = <1>;
                };
--

2.17.1