iio: temperature: mlx90632: Add extended calibration calculations
Subsystems (2)
Crt Mori
maintainerv6 cover iio: temperature: mlx90632: Add extended calibration calculations
Add extended calibration calculations for the new subversion of DSP5.
V6 review comments from Andy Shevchenko <[email protected]:
- Covert all while loops to regmap_read_poll_timeout or read_poll_timeout even though udelay of more than 20ms is used in the second. Problem was, that timeout needs to be 800ms, while polling frequency could be 20ms, but we konw that that will generate more noise on line than needed. Did some tests and current number combination seems best. This also caused that commit messages were adjusted.
V5 review comments from Andy Shevchenko <[email protected]:
- Swap order of patches to avoid re-doing the calculations
- Add fixed name defines for Ambient and Object RAM temperature channels as per suggestion of the Jonathan Cameron <[email protected]>
V5:
- Add style changes patch along with current series.
V4 review comments from Andy Shevchenko <[email protected]>:
- Move the function creation for Ta4 to first patch
- Add kernel doc patch for documenting internal struct
- Add patch to convert while loops to do-while loops for polling
V3 review comments from Andy Shevchenko <[email protected]>:
- Change commit message text to more proper English as per suggestions
- Drop unneeded brackets and parentheses
- Use defines from limits.h
- Remove userspace typedefs as leftovers from porting
- Testing of timeout loops with iopoll.h was no successful, because delay between measurements is 10ms, but we need to fill at least 3 channels, so final timeout should be 40ms which is out of scope of usleep function
- Fixing some typos in comments
V2 review comments from Andy Shevchenko <[email protected]>:
- Convert divison back to shifts to make it more readable
Crt Mori (5):
iio:temperature:mlx90632: Reduce number of equal calulcations iio:temperature:mlx90632: Add kerneldoc to the internal struct iio:temperature:mlx90632: Convert polling while loop to regmap iio:temperature:mlx90632: Adding extended calibration option iio:temperature:mlx90632: Some stylefixing leftovers
drivers/iio/temperature/mlx90632.c | 274 ++++++++++++++++++++++++++--- 1 file changed, 247 insertions(+), 27 deletions(-)
Signature · 1 line
2.25.1
Crt Mori
maintainerPATCH v6 1/5 iio:temperature:mlx90632: Reduce number of equal calulcations
TAdut4 was calculated each iteration although it did not change. In light of near future additions of the Extended range DSP calculations, this function refactoring will help reduce unrelated changes in that series as well as reduce the number of new functions needed.
--- drivers/iio/temperature/mlx90632.c | 21 +++++++++++++-------- 1 file changed, 13 insertions(+), 8 deletions(-)
drivers/iio/temperature/mlx90632.c +13 -8
@@ -374,11 +374,11 @@ static s32 mlx90632_calc_temp_ambient(s16 ambient_new_raw, s16 ambient_old_raw, }static s32 mlx90632_calc_temp_object_iteration (s32 prev_object_temp,s64 object, -s64 TAdut,s32 Fa,s32 Fb, +s64 TAdut,s64 TAdut4,s32 Fa,s32 Fb,s32 Ga,s16 Ha,s16 Hb,u16 emissivity) { -s64 calcedKsTO, calcedKsTA, ir_Alpha, TAdut4, Alpha_corr; +s64 calcedKsTO, calcedKsTA, ir_Alpha, Alpha_corr;s64 Ha_customer, Hb_customer; Ha_customer = ((s64 )Ha *1000000LL ) >>14ULL ;
@@ -393,30 +393,35 @@ static s32 mlx90632_calc_temp_object_iteration(s32 prev_object_temp, s64 object, Alpha_corr = emissivity *div64_s64 (Alpha_corr,100000LL ); Alpha_corr =div64_s64 (Alpha_corr,1000LL ); ir_Alpha =div64_s64 ((s64 )object *10000000LL , Alpha_corr); - TAdut4 = (div64_s64 (TAdut,10000LL ) +27315 ) * - (div64_s64 (TAdut,10000LL ) +27315 ) * - (div64_s64 (TAdut,10000LL ) +27315 ) * - (div64_s64 (TAdut,10000LL ) +27315 );return (int_sqrt64 (int_sqrt64 (ir_Alpha *1000000000000LL + TAdut4)) -27315 - Hb_customer) *10 ; } +static s64 mlx90632_calc_ta4 (s64 TAdut,s64 scale) +{ +return (div64_s64 (TAdut, scale) +27315 ) * + (div64_s64 (TAdut, scale) +27315 ) * + (div64_s64 (TAdut, scale) +27315 ) * + (div64_s64 (TAdut, scale) +27315 ); +} +static s32 mlx90632_calc_temp_object (s64 object,s64 ambient,s32 Ea,s32 Eb,s32 Fa,s32 Fb,s32 Ga,s16 Ha,s16 Hb,u16 tmp_emi) { -s64 kTA, kTA0, TAdut; +s64 kTA, kTA0, TAdut, TAdut4;s64 temp =25000 ;s8 i; kTA = (Ea *1000LL ) >>16LL ; kTA0 = (Eb *1000LL ) >>8LL ; TAdut =div64_s64 (((ambient - kTA0) *1000000LL ), kTA) +25 *1000000LL ; + TAdut4 =mlx90632_calc_ta4 (TAdut,10000LL );/* Iterations of calculation as described in datasheet */ for (i =0 ; i <5 ; ++i) { - temp =mlx90632_calc_temp_object_iteration (temp, object, TAdut, + temp =mlx90632_calc_temp_object_iteration (temp, object, TAdut, TAdut4, Fa, Fb, Ga, Ha, Hb, tmp_emi); }
Signature · 1 line
2.25.1
Crt Mori
maintainerPATCH v6 2/5 iio:temperature:mlx90632: Add kerneldoc to the internal struct
In reply to Crt MoriDocument internal/private struct for mlx90632 device.
--- drivers/iio/temperature/mlx90632.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)
drivers/iio/temperature/mlx90632.c +8 -1
@@ -89,9 +89,16 @@#define MLX90632_MAX_MEAS_NUM 31/**< Maximum measurements in list */ #define MLX90632_SLEEP_DELAY_MS 3000/**< Autosleep delay */ +/** +* struct mlx90632_data - private data for the MLX90632 device +* @client: I2C client of the device +* @lock: Internal mutex for multiple reads for single measurement +* @regmap: Regmap of the device +* @emissivity: Object emissivity from 0 to 1000 where 1000 = 1. +*/ struct mlx90632_data {struct i2c_client *client; -struct mutex lock;/* Multiple reads for single measurement */ +struct mutex lock;struct regmap *regmap;u16 emissivity; };
Signature · 1 line
2.25.1
Crt Mori
maintainerPATCH v6 3/5 iio:temperature:mlx90632: Convert polling while loop to regmap
In reply to Crt MoriReduce number of lines and improve readability to convert polling while loops to regmap_read_poll_timeout.
--- drivers/iio/temperature/mlx90632.c | 16 +++++----------- 1 file changed, 5 insertions(+), 11 deletions(-)
drivers/iio/temperature/mlx90632.c +5 -11
@@ -180,25 +180,19 @@ static s32 mlx90632_pwr_continuous(struct regmap *regmap)*/ static int mlx90632_perform_measurement (struct mlx90632_data *data) { -int ret, tries =100 ;unsigned int reg_status; +int ret; ret =regmap_update_bits (data->regmap,MLX90632_REG_STATUS ,MLX90632_STAT_DATA_RDY ,0 );if (ret <0 )return ret; -while (tries-- >0 ) { - ret =regmap_read (data->regmap,MLX90632_REG_STATUS , - ®_status); -if (ret <0 ) -return ret; -if (reg_status &MLX90632_STAT_DATA_RDY ) -break ; -usleep_range (10000 ,11000 ); - } + ret =regmap_read_poll_timeout (data->regmap,MLX90632_REG_STATUS , reg_status, + !(reg_status &MLX90632_STAT_DATA_RDY ),10000 , +100 *10000 ); -if (tries <0 ) { +if (ret <0 ) {dev_err (&data->client->dev,"data not ready" );return -ETIMEDOUT ; }
Signature · 1 line
2.25.1
Re: [PATCH v6 3/5] iio:temperature:mlx90632: Convert polling while loop to regmap
Quoted 3 lines · Crt Mori
Reduce number of lines and improve readability to convert polling while loops to
regmap_read_poll_timeout.
Usually we refer to a function as regmap_read_poll_timeout(). Note parentheses. I think Jonathan can fix when applying, no need to resend.
Precisely what I meant, thanks!
Quoted 41 lines
Signed-off-by Crt Mori <[email protected]>--- drivers/iio/temperature/mlx90632.c | 16 +++++----------- 1 file changed, 5 insertions(+), 11 deletions(-)drivers/iio/temperature/mlx90632.c +5
-12@@ -180,25 +180,19 @@ static s32 mlx90632_pwr_continuous(struct regmap *regmap)*/ static int mlx90632_perform_measurement (struct mlx90632_data *data) { -int ret, tries =100 ;unsigned int reg_status; +int ret; ret =regmap_update_bits (data->regmap,MLX90632_REG_STATUS ,MLX90632_STAT_DATA_RDY ,0 );if (ret <0 )return ret; -while (tries-- >0 ) { - ret =regmap_read (data->regmap,MLX90632_REG_STATUS , - ®_status); -if (ret <0 ) -return ret; -if (reg_status &MLX90632_STAT_DATA_RDY ) -break ; -usleep_range (10000 ,11000 ); - } + ret =regmap_read_poll_timeout (data->regmap,MLX90632_REG_STATUS , reg_status, + !(reg_status &MLX90632_STAT_DATA_RDY ),10000 , +100 *10000 ); -if (tries <0 ) { +if (ret <0 ) {dev_err (&data->client->dev,"data not ready" );return -ETIMEDOUT ; } --
Quoted 2 lines
2.25.1
--
With Best Regards,
Andy Shevchenko
Crt Mori
maintainerPATCH v6 4/5 iio:temperature:mlx90632: Adding extended calibration option
In reply to Crt MoriFor some time the market wants medical grade accuracy in medical range, while still retaining the declared accuracy outside of the medical range within the same sensor. That is why we created extended calibration which is automatically switched to when object temperature is too high.
This patch also introduces the object_ambient_temperature variable which is needed for more accurate calculation of the object infra-red footprint as sensor's ambient temperature might be totally different than what the ambient temperature is at object and that is why we can have some more errors which can be eliminated. Currently this temperature is fixed at 25, but the interface to adjust it by user (with external sensor or just IR measurement of the other object which acts as ambient), will be introduced in another commit.
--- drivers/iio/temperature/mlx90632.c | 218 ++++++++++++++++++++++++++++- 1 file changed, 216 insertions(+), 2 deletions(-)
drivers/iio/temperature/mlx90632.c +216 -2
@@ -10,7 +10,9 @@#include <linux/err.h> #include <linux/gpio/consumer.h> #include <linux/i2c.h> +#include <linux/iopoll.h> #include <linux/kernel.h> +#include <linux/limits.h> #include <linux/module.h> #include <linux/math64.h> #include <linux/of.h>
@@ -58,6 +60,8 @@/* Control register address - volatile */ #define MLX90632_REG_CONTROL 0x3001/* Control Register address */ #define MLX90632_CFG_PWR_MASK GENMASK(2, 1)/* PowerMode Mask */ +#define MLX90632_CFG_MTYP_MASK GENMASK(8, 4)/* Meas select Mask */ +/* PowerModes statuses */ #define MLX90632_PWR_STATUS (ctrl_val) (ctrl_val << 1)#define MLX90632_PWR_STATUS_HALT MLX90632_PWR_STATUS(0)/* hold */
@@ -65,6 +69,18 @@#define MLX90632_PWR_STATUS_STEP MLX90632_PWR_STATUS(2)/* step */ #define MLX90632_PWR_STATUS_CONTINUOUS MLX90632_PWR_STATUS(3)/* continuous*/ +/* Measurement types */ +#define MLX90632_MTYP_MEDICAL 0 +#define MLX90632_MTYP_EXTENDED 17 + +/* Measurement type select*/ +#define MLX90632_MTYP_STATUS (ctrl_val) (ctrl_val << 4) +#define MLX90632_MTYP_STATUS_MEDICAL MLX90632_MTYP_STATUS(MLX90632_MTYP_MEDICAL) +#define MLX90632_MTYP_STATUS_EXTENDED MLX90632_MTYP_STATUS(MLX90632_MTYP_EXTENDED) + +/* I2C command register - volatile */ +#define MLX90632_REG_I2C_CMD 0x3005/* I2C command Register address */ +/* Device status register - volatile */ #define MLX90632_REG_STATUS 0x3fff/* Device status register */ #define MLX90632_STAT_BUSY BIT(10)/* Device busy indicator */
@@ -78,9 +94,21 @@#define MLX90632_RAM_2 (meas_num) (MLX90632_ADDR_RAM + 3 * meas_num + 1)#define MLX90632_RAM_3 (meas_num) (MLX90632_ADDR_RAM + 3 * meas_num + 2) +/* Name important RAM_MEAS channels */ +#define MLX90632_RAM_DSP5_EXTENDED_AMBIENT_1 MLX90632_RAM_3(17) +#define MLX90632_RAM_DSP5_EXTENDED_AMBIENT_2 MLX90632_RAM_3(18) +#define MLX90632_RAM_DSP5_EXTENDED_OBJECT_1 MLX90632_RAM_1(17) +#define MLX90632_RAM_DSP5_EXTENDED_OBJECT_2 MLX90632_RAM_2(17) +#define MLX90632_RAM_DSP5_EXTENDED_OBJECT_3 MLX90632_RAM_1(18) +#define MLX90632_RAM_DSP5_EXTENDED_OBJECT_4 MLX90632_RAM_2(18) +#define MLX90632_RAM_DSP5_EXTENDED_OBJECT_5 MLX90632_RAM_1(19) +#define MLX90632_RAM_DSP5_EXTENDED_OBJECT_6 MLX90632_RAM_2(19) +/* Magic constants */ #define MLX90632_ID_MEDICAL 0x0105/* EEPROM DSPv5 Medical device id */ #define MLX90632_ID_CONSUMER 0x0205/* EEPROM DSPv5 Consumer device id */ +#define MLX90632_ID_EXTENDED 0x0505/* EEPROM DSPv5 Extended range device id */ +#define MLX90632_ID_MASK GENMASK(14, 0)/* DSP version and device ID in EE_VERSION */ #define MLX90632_DSP_VERSION 5/* DSP version */ #define MLX90632_DSP_MASK GENMASK(7, 0)/* DSP version in EE_VERSION */ #define MLX90632_RESET_CMD 0x0006/* Reset sensor (address or global) */
@@ -88,6 +116,7 @@#define MLX90632_REF_3 12LL/**< ResCtrlRef value of Channel 3 */ #define MLX90632_MAX_MEAS_NUM 31/**< Maximum measurements in list */ #define MLX90632_SLEEP_DELAY_MS 3000/**< Autosleep delay */ +#define MLX90632_EXTENDED_LIMIT 27000/* Extended mode raw value limit */ /** * struct mlx90632_data - private data for the MLX90632 device
@@ -95,16 +124,23 @@* @lock: Internal mutex for multiple reads for single measurement * @regmap: Regmap of the device * @emissivity: Object emissivity from 0 to 1000 where 1000 = 1. +* @mtyp: Measurement type physical sensor configuration for extended range +* calculations +* @object_ambient_temperature: Ambient temperature at object (might differ of +* the ambient temperature of sensor. */ struct mlx90632_data {struct i2c_client *client;struct mutex lock;struct regmap *regmap;u16 emissivity; +u8 mtyp; +u32 object_ambient_temperature; };static const struct regmap_range mlx90632_volatile_reg_range[] = {regmap_reg_range (MLX90632_REG_I2C_ADDR ,MLX90632_REG_CONTROL ), +regmap_reg_range (MLX90632_REG_I2C_CMD ,MLX90632_REG_I2C_CMD ),regmap_reg_range (MLX90632_REG_STATUS ,MLX90632_REG_STATUS ),regmap_reg_range (MLX90632_RAM_1 (0 ),MLX90632_RAM_3 (MLX90632_MAX_MEAS_NUM )),
@@ -120,6 +156,7 @@ static const struct regmap_range mlx90632_read_reg_range[] = {regmap_reg_range (MLX90632_EE_CTRL ,MLX90632_EE_I2C_ADDR ),regmap_reg_range (MLX90632_EE_Ha, MLX90632_EE_Hb),regmap_reg_range (MLX90632_REG_I2C_ADDR ,MLX90632_REG_CONTROL ), +regmap_reg_range (MLX90632_REG_I2C_CMD ,MLX90632_REG_I2C_CMD ),regmap_reg_range (MLX90632_REG_STATUS ,MLX90632_REG_STATUS ),regmap_reg_range (MLX90632_RAM_1 (0 ), MLX90632_RAM_3(MLX90632_MAX_MEAS_NUM)),
@@ -200,6 +237,26 @@ static int mlx90632_perform_measurement(struct mlx90632_data *data)return (reg_status &MLX90632_STAT_CYCLE_POS ) >>2 ; } +static int mlx90632_set_meas_type (struct regmap *regmap,u8 type) +{ +int ret; + +if ((type !=MLX90632_MTYP_MEDICAL ) && (type !=MLX90632_MTYP_EXTENDED )) +return -EINVAL ; + + ret =regmap_write (regmap,MLX90632_REG_I2C_CMD ,MLX90632_RESET_CMD ); +if (ret <0 ) +return ret; + + ret =regmap_write_bits (regmap,MLX90632_REG_CONTROL , + (MLX90632_CFG_MTYP_MASK |MLX90632_CFG_PWR_MASK ), + (MLX90632_MTYP_STATUS (type) |MLX90632_PWR_STATUS_HALT )); +if (ret <0 ) +return ret; + +return mlx90632_pwr_continuous (regmap); +} +static int mlx90632_channel_new_select (int perform_ret,uint8_t *channel_new,uint8_t *channel_old) {
@@ -301,6 +358,97 @@ static int mlx90632_read_all_channel(struct mlx90632_data *data,return ret; } +static int mlx90632_read_ambient_raw_extended (struct regmap *regmap, +s16 *ambient_new_raw,s16 *ambient_old_raw) +{ +unsigned int read_tmp; +int ret; + + ret =regmap_read (regmap,MLX90632_RAM_DSP5_EXTENDED_AMBIENT_1 , &read_tmp); +if (ret <0 ) +return ret; + *ambient_new_raw = (s16 )read_tmp; + + ret =regmap_read (regmap,MLX90632_RAM_DSP5_EXTENDED_AMBIENT_2 , &read_tmp); +if (ret <0 ) +return ret; + *ambient_old_raw = (s16 )read_tmp; + +return 0 ; +} + +static int mlx90632_read_object_raw_extended (struct regmap *regmap,s16 *object_new_raw) +{ +unsigned int read_tmp; +s32 read; +int ret; + + ret =regmap_read (regmap,MLX90632_RAM_DSP5_EXTENDED_OBJECT_1 , &read_tmp); +if (ret <0 ) +return ret; + read = (s16 )read_tmp; + + ret =regmap_read (regmap,MLX90632_RAM_DSP5_EXTENDED_OBJECT_2 , &read_tmp); +if (ret <0 ) +return ret; + read = read - (s16 )read_tmp; + + ret =regmap_read (regmap,MLX90632_RAM_DSP5_EXTENDED_OBJECT_3 , &read_tmp); +if (ret <0 ) +return ret; + read = read - (s16 )read_tmp; + + ret =regmap_read (regmap,MLX90632_RAM_DSP5_EXTENDED_OBJECT_4 , &read_tmp); +if (ret <0 ) +return ret; + read = (read + (s16 )read_tmp) /2 ; + + ret =regmap_read (regmap,MLX90632_RAM_DSP5_EXTENDED_OBJECT_5 , &read_tmp); +if (ret <0 ) +return ret; + read = read + (s16 )read_tmp; + + ret =regmap_read (regmap,MLX90632_RAM_DSP5_EXTENDED_OBJECT_6 , &read_tmp); +if (ret <0 ) +return ret; + read = read + (s16 )read_tmp; + +if (read >S16_MAX || read <S16_MIN ) +return -ERANGE ; + + *object_new_raw = read; + +return 0 ; +} + +static int mlx90632_read_all_channel_extended (struct mlx90632_data *data,s16 *object_new_raw, +s16 *ambient_new_raw,s16 *ambient_old_raw) +{ +s32 ret, meas; + +mutex_lock (&data->lock); + ret =mlx90632_set_meas_type (data->regmap,MLX90632_MTYP_EXTENDED ); +if (ret <0 ) + goto read_unlock; + + ret =read_poll_timeout (mlx90632_perform_measurement, meas, meas ==19 , +50000 ,800000 , false, data); +if (ret !=0 ) + goto read_unlock; + + ret =mlx90632_read_object_raw_extended (data->regmap, object_new_raw); +if (ret <0 ) + goto read_unlock; + + ret =mlx90632_read_ambient_raw_extended (data->regmap, ambient_new_raw, ambient_old_raw); + +read_unlock: + (void )mlx90632_set_meas_type (data->regmap,MLX90632_MTYP_MEDICAL ); + +mutex_unlock (&data->lock); +return ret; +} +static int mlx90632_read_ee_register (struct regmap *regmap,u16 reg_lsb,s32 *reg_value) {
@@ -355,9 +503,23 @@ static s64 mlx90632_preprocess_temp_obj(s16 object_new_raw, s16 object_old_raw,return div64_s64 ((tmp <<19ULL ),1000LL ); } +static s64 mlx90632_preprocess_temp_obj_extended (s16 object_new_raw,s16 ambient_new_raw, +s16 ambient_old_raw,s16 Ka) +{ +s64 VR_IR , kKa, tmp; + + kKa = ((s64 )Ka *1000LL ) >>10ULL ; +VR_IR = (s64 )ambient_old_raw *1000000LL + + kKa *div64_s64 ((s64 )ambient_new_raw *1000LL , +MLX90632_REF_3 ); + tmp =div64_s64 ( +div64_s64 ((s64 ) object_new_raw *1000000000000LL ,MLX90632_REF_12 ), +VR_IR ); +return div64_s64 (tmp <<19ULL ,1000LL ); +} +static s32 mlx90632_calc_temp_ambient (s16 ambient_new_raw,s16 ambient_old_raw, -s32 P_T ,s32 P_R ,s32 P_G ,s32 P_O , -s16 Gb) +s32 P_T ,s32 P_R ,s32 P_G ,s32 P_O ,s16 Gb) {s64 Asub, Bsub, Ablock, Bblock, Cblock,AMB , sum;
@@ -429,6 +591,31 @@ static s32 mlx90632_calc_temp_object(s64 object, s64 ambient, s32 Ea, s32 Eb,return temp; } +static s32 mlx90632_calc_temp_object_extended (s64 object,s64 ambient,s64 reflected, +s32 Ea,s32 Eb,s32 Fa,s32 Fb,s32 Ga, +s16 Ha,s16 Hb,u16 tmp_emi) +{ +s64 kTA, kTA0, TAdut, TAdut4, Tr4, TaTr4; +s64 temp =25000 ; +s8 i; + + kTA = (Ea *1000LL ) >>16LL ; + kTA0 = (Eb *1000LL ) >>8LL ; + TAdut =div64_s64 ((ambient - kTA0) *1000000LL , kTA) +25 *1000000LL ; + Tr4 =mlx90632_calc_ta4 (reflected,10 ); + TAdut4 =mlx90632_calc_ta4 (TAdut,10000LL ); + TaTr4 = Tr4 -div64_s64 (Tr4 - TAdut4, tmp_emi) *1000 ; + +/* Iterations of calculation as described in datasheet */ +for (i =0 ; i <5 ; ++i) { + temp =mlx90632_calc_temp_object_iteration (temp, object, TAdut, TaTr4, + Fa /2 , Fb, Ga, Ha, Hb, + tmp_emi); + } + +return temp; +} +static int mlx90632_calc_object_dsp105 (struct mlx90632_data *data,int *val) {s32 ret;
@@ -476,6 +663,26 @@ static int mlx90632_calc_object_dsp105(struct mlx90632_data *data, int *val)if (ret <0 )return ret; +if (object_new_raw >MLX90632_EXTENDED_LIMIT && + data->mtyp ==MLX90632_MTYP_EXTENDED ) { + ret =mlx90632_read_all_channel_extended (data, &object_new_raw, + &ambient_new_raw, &ambient_old_raw); +if (ret <0 ) +return ret; + +/* Use extended mode calculations */ + ambient =mlx90632_preprocess_temp_amb (ambient_new_raw, + ambient_old_raw, Gb); + object =mlx90632_preprocess_temp_obj_extended (object_new_raw, + ambient_new_raw, + ambient_old_raw, Ka); + *val =mlx90632_calc_temp_object_extended (object, ambient, + data->object_ambient_temperature, + Ea, Eb, Fa, Fb, Ga, + Ha, Hb, data->emissivity); +return 0 ; + } + ambient =mlx90632_preprocess_temp_amb (ambient_new_raw, ambient_old_raw, Gb); object = mlx90632_preprocess_temp_obj(object_new_raw,
@@ -649,6 +856,7 @@ static int mlx90632_probe(struct i2c_client *client,i2c_set_clientdata (client, indio_dev); mlx90632->client = client; mlx90632->regmap = regmap; + mlx90632->mtyp =MLX90632_MTYP_MEDICAL ;mutex_init (&mlx90632->lock); indio_dev->name = id->name;
@@ -668,12 +876,17 @@ static int mlx90632_probe(struct i2c_client *client,dev_err (&client->dev,"read of version failed: %d\n" , ret);return ret; } + read = read &MLX90632_ID_MASK ;if (read ==MLX90632_ID_MEDICAL ) {dev_dbg (&client->dev,"Detected Medical EEPROM calibration %x\n" , read); }else if (read ==MLX90632_ID_CONSUMER ) {dev_dbg (&client->dev,"Detected Consumer EEPROM calibration %x\n" , read); + }else if (read ==MLX90632_ID_EXTENDED ) { +dev_dbg (&client->dev, +"Detected Extended range EEPROM calibration %x\n" , read); + mlx90632->mtyp =MLX90632_MTYP_EXTENDED ; }else if ((read &MLX90632_DSP_MASK ) ==MLX90632_DSP_VERSION ) {dev_dbg (&client->dev,"Detected Unknown EEPROM calibration %x\n" , read);
@@ -685,6 +898,7 @@ static int mlx90632_probe(struct i2c_client *client, } mlx90632->emissivity =1000 ; + mlx90632->object_ambient_temperature =25000 ;/* 25 degrees milliCelsius */ pm_runtime_disable (&client->dev); ret =pm_runtime_set_active (&client->dev);
Signature · 1 line
2.25.1
Crt Mori
maintainerPATCH v6 5/5 iio:temperature:mlx90632: Some stylefixing leftovers
In reply to Crt MoriThere is some inconsistency and whitespace cleanup performed in this patch. It was done on top of my other patches, but I can rebase to head of the togreg branch if it would go in sooner.
--- drivers/iio/temperature/mlx90632.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-)
drivers/iio/temperature/mlx90632.c +5 -5
@@ -112,10 +112,10 @@#define MLX90632_DSP_VERSION 5/* DSP version */ #define MLX90632_DSP_MASK GENMASK(7, 0)/* DSP version in EE_VERSION */ #define MLX90632_RESET_CMD 0x0006/* Reset sensor (address or global) */ -#define MLX90632_REF_12 12LL/**< ResCtrlRef value of Ch 1 or Ch 2 */ -#define MLX90632_REF_3 12LL/**< ResCtrlRef value of Channel 3 */ -#define MLX90632_MAX_MEAS_NUM 31/**< Maximum measurements in list */ -#define MLX90632_SLEEP_DELAY_MS 3000/**< Autosleep delay */ +#define MLX90632_REF_12 12LL/* ResCtrlRef value of Ch 1 or Ch 2 */ +#define MLX90632_REF_3 12LL/* ResCtrlRef value of Channel 3 */ +#define MLX90632_MAX_MEAS_NUM 31/* Maximum measurements in list */ +#define MLX90632_SLEEP_DELAY_MS 3000/* Autosleep delay */ #define MLX90632_EXTENDED_LIMIT 27000/* Extended mode raw value limit */ /**
@@ -889,7 +889,7 @@ static int mlx90632_probe(struct i2c_client *client, mlx90632->mtyp =MLX90632_MTYP_EXTENDED ; }else if ((read &MLX90632_DSP_MASK ) ==MLX90632_DSP_VERSION ) {dev_dbg (&client->dev, -"Detected Unknown EEPROM calibration %x\n" , read); +"Detected Unknown EEPROM calibration %x\n" , read); }else { dev_err(&client->dev, "Wrong DSP version %x (expected %x)\n",
Signature · 1 line
2.25.1
Re: [PATCH v6 5/5] iio:temperature:mlx90632: Some stylefixing leftovers
Quoted 4 lines · Crt Mori
There is some inconsistency and whitespace cleanup performed in this patch. It was done on top of my other patches, but I can rebase to head of the togreg branch if it would go in sooner.
Quoted 34 lines
Signed-off-by Crt Mori <[email protected]>--- drivers/iio/temperature/mlx90632.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-)drivers/iio/temperature/mlx90632.c +5
-6@@ -112,10 +112,10 @@#define MLX90632_DSP_VERSION 5/* DSP version */ #define MLX90632_DSP_MASK GENMASK(7, 0)/* DSP version in EE_VERSION */ #define MLX90632_RESET_CMD 0x0006/* Reset sensor (address or global) */ -#define MLX90632_REF_12 12LL/**< ResCtrlRef value of Ch 1 or Ch 2 */ -#define MLX90632_REF_3 12LL/**< ResCtrlRef value of Channel 3 */ -#define MLX90632_MAX_MEAS_NUM 31/**< Maximum measurements in list */ -#define MLX90632_SLEEP_DELAY_MS 3000/**< Autosleep delay */ +#define MLX90632_REF_12 12LL/* ResCtrlRef value of Ch 1 or Ch 2 */ +#define MLX90632_REF_3 12LL/* ResCtrlRef value of Channel 3 */ +#define MLX90632_MAX_MEAS_NUM 31/* Maximum measurements in list */ +#define MLX90632_SLEEP_DELAY_MS 3000/* Autosleep delay */ #define MLX90632_EXTENDED_LIMIT 27000/* Extended mode raw value limit */ /** @@ -889,7 +889,7 @@ static int mlx90632_probe(struct i2c_client *client, mlx90632->mtyp =MLX90632_MTYP_EXTENDED ; }else if ((read &MLX90632_DSP_MASK ) ==MLX90632_DSP_VERSION ) {dev_dbg (&client->dev, -"Detected Unknown EEPROM calibration %x\n" , read); +"Detected Unknown EEPROM calibration %x\n" , read); }else { dev_err(&client->dev, "Wrong DSP version %x (expected %x)\n", --
Quoted 2 lines
2.25.1
--
With Best Regards,
Andy Shevchenko
Jonathan Cameron
maintainerQuoted 44 lines · On Tue, 18 Aug 2020 23:37:32 +0200 Crt Mori <[email protected]> wrote:
Add extended calibration calculations for the new subversion of DSP5.
V6 review comments from Andy Shevchenko <[email protected]:
- Covert all while loops toregmap_read_poll_timeoutorread_poll_timeouteven though udelay of more than 20ms is used in the second. Problem was, that timeout needs to be 800ms, while polling frequency could be 20ms, but we konw that that will generate more noise on line than needed. Did some tests and current number combination seems best. This also caused that commit messages were adjusted.
V5 review comments from Andy Shevchenko <[email protected]:
- Swap order of patches to avoid re-doing the calculations
- Add fixed name defines for Ambient and Object RAM temperature channels as per suggestion of the Jonathan Cameron <[email protected]>
V5:
- Add style changes patch along with current series.V4 review comments from Andy Shevchenko <[email protected]>:
- Move the function creation for Ta4 to first patch
- Add kernel doc patch for documenting internal struct
- Add patch to convert while loops to do-while loops for pollingV3 review comments from Andy Shevchenko <[email protected]>:
- Change commit message text to more proper English as per suggestions
- Drop unneeded brackets and parentheses
- Use defines fromlimits.h
- Remove userspace typedefs as leftovers from porting
- Testing of timeout loops withiopoll.hwas no successful, because delay between measurements is 10ms, but we need to fill at least 3 channels, so final timeout should be 40ms which is out of scope of usleep function
- Fixing some typos in commentsV2 review comments from Andy Shevchenko <[email protected]>:
- Convert divison back to shifts to make it more readableCrt Mori (5):
iio:temperature:mlx90632: Reduce number of equal calulcations iio:temperature:mlx90632: Add kerneldoc to the internal struct iio:temperature:mlx90632: Convert polling while loop to regmap iio:temperature:mlx90632: Adding extended calibration option iio:temperature:mlx90632: Some stylefixing leftovers
Quoted 3 lines
drivers/iio/temperature/mlx90632.c | 274 ++++++++++++++++++++++++++--- 1 file changed, 247 insertions(+), 27 deletions(-)
Thanks. Also thanks to Andy for all his review work on these!
Applied to the togreg branch of iio.git and pushed out as testing for the autobuilders to try and break it.
Thanks,
Jonathan