configure: add support for pseudo-"in source tree" builds
PATCH v2 1/1 configure: add support for pseudo-"in source tree" builds
Meson requires the build dir to be separate from the source tree. Many people are used to just running "./configure && make" though and the meson conversion breaks that.
This introduces some backcompat support to make it appear as if an "in source tree" build is being done, but with the the results in the "build/" directory. This allows "./configure && make" to work as it did historically, albeit with the output binaries staying under build/.
---
This is a simple integration of Eric's proposal from
https://lists.gnu.org/archive/html/qemu-devel/2020-03/msg07290.html
with a bit of configure magic. It is enough to enable
./configure
make
make check
I've not tested it beyond that. Note it blows away the "build/" dir each time ./configure is run so it is pristine each time.
We could optionally symlink binaries from build/ into $PWD if people think that is important, eg by changing GNUmakefile to have:
recurse: all
for bin in `find build -maxdepth 1 -type f -executable | grep -v -E '(ninjatool|config.status)'`; \
do \
ln -f -s $$bin . ; \
doneand some cleanup logic to purge the symlinks for "make clean"
This goes on top of Paolo's most recent meson port v175 posting, or whatever number it is upto now :-)
In v2:
- Use a marker file so we don't blow away a build/ dir we didn't create
- Silence the distclean rule
- Fix broken use of error_exit that's not defined yet
- Add comment to GNUmakefile
.gitignore | 2 ++ configure | 48 +++++++++++++++++++++++++++++++++++++++++++++--- 2 files changed, 47 insertions(+), 3 deletions(-)
.gitignore +2 -0
@@ -1,3 +1,5 @@ +/GNUmakefile +/build/ /.doctrees /config-devices.* /config-all-devices.*
configure +45 -3
60 lines not on this page · raw message
Signature · 1 line
2.26.2
Quoted 77 lines · Daniel P. Berrangé
Meson requires the build dir to be separate from the source tree. Many people are used to just running "./configure && make" though and the meson conversion breaks that.
This introduces some backcompat support to make it appear as if an "in source tree" build is being done, but with the the results in the "build/" directory. This allows "./configure && make" to work as it did historically, albeit with the output binaries staying under build/.
Signed-off-by Daniel P. Berrangé <[email protected]>---
This is a simple integration of Eric's proposal from
https://lists.gnu.org/archive/html/qemu-devel/2020-03/msg07290.html
with a bit of configure magic. It is enough to enable
./configure
make
make checkI've not tested it beyond that. Note it blows away the "build/" dir each time ./configure is run so it is pristine each time.
We could optionally symlink binaries from build/ into $PWD if people think that is important, eg by changing GNUmakefile to have:
recurse: all
for bin in `find build -maxdepth 1 -type f -executable | grep -v -E '(ninjatool|config.status)'`; \ do \ ln -f -s $$bin . ; \ doneand some cleanup logic to purge the symlinks for "make clean"
This goes on top of Paolo's most recent meson port v175 posting, or whatever number it is upto now :-)
In v2:
- Use a marker file so we don't blow away a build/ dir we didn't create
- Silence the distclean rule
- Fix broken use oferror_exitthat's not defined yet
- Add comment to GNUmakefile.gitignore | 2 ++ configure | 48 +++++++++++++++++++++++++++++++++++++++++++++--- 2 files changed, 47 insertions(+), 3 deletions(-).gitignore +2
-0@@ -1,3 +1,5 @@ +/GNUmakefile +/build/ /.doctrees /config-devices.* /config-all-devices.*configure +7
-0@@ -11,6 +11,51 @@ unset CLICOLOR_FORCE GREP_OPTIONS # Don't allow CCACHE, if present, to use cached results of compile tests! export CCACHE_RECACHE=yes +# make source path absolute +source_path=$(cd "$(dirname -- "$0")"; pwd) + +if test "$PWD" == "$source_path" +then + echo "Using './build' as the directory for build output" +
configure unset CLICOLOR_FORCE GREP_OPTIONS · line 30
Quoted 10 lines
configure +10
-0+ MARKER=build/auto-created-by-configure + + if test -e build + then + if test -f $MARKER + then + rm -rf build + else + echo "ERROR: ./build dir already exists and was not previously created by configure" + exit 1
Tested normal build in fresh clone, then in my current workdir:
./configure
Using './build' as the directory for build output
ERROR: ./build dir already exists and was not previously created by configure
Quoted 42 lines
configure +28
-3+ fi + fi + + mkdir build + touch $MARKER + + cat > GNUmakefile <<EOF +# This file is auto-generated by configure to support in-source tree +# 'make' command invokation + +ifeq (\$(MAKECMDGOALS),) +recurse: all +endif + +.NOTPARALLEL: % +%: force + @echo 'changing dir to build for \$(MAKE) "\$(MAKECMDGOALS)"...' + @\$(MAKE) -C build -f Makefile \$(MAKECMDGOALS) + @if test "\$(MAKECMDGOALS)" = "distclean" && test -e build/auto-created-by-configure ; then rm -rf build GNUmakefile ; fi +force: ; +.PHONY: force +GNUmakefile: ; + +EOF + cd build + exec $source_path/configure "$@" +fi + # Temporary directory used for files created while # configure runs. Since it is in the build directory # we can safely blow away any previous version of it@@ -297,9 +342,6 @@ ld_has() { $ld --help 2>/dev/null | grep ".$1" >/dev/null 2>&1 } -# make source path absolute -source_path=$(cd "$(dirname -- "$0")"; pwd) - if printf %s\\n "$source_path" "$PWD" | grep -q "[[:space:]:]"; then error_exit "main directory cannot contain spaces nor colons"
Quoted 6 lines · Daniel P. Berrangé
Meson requires the build dir to be separate from the source tree. Many people are used to just running "./configure && make" though and the meson conversion breaks that.
This introduces some backcompat support to make it appear as if an "in source tree" build is being done, but with the the results in the
s/the the/the/
Quoted 35 lines
"build/" directory. This allows "./configure && make" to work as it did historically, albeit with the output binaries staying under build/.
Signed-off-by Daniel P. Berrangé <[email protected]>---
In v2:
- Use a marker file so we don't blow away a build/ dir we didn't create
- Silence the distclean rule
- Fix broken use oferror_exitthat's not defined yet
- Add comment to GNUmakefile.gitignore | 2 ++ configure | 48 +++++++++++++++++++++++++++++++++++++++++++++--- 2 files changed, 47 insertions(+), 3 deletions(-).gitignore +2
-0@@ -1,3 +1,5 @@ +/GNUmakefile +/build/ /.doctrees /config-devices.* /config-all-devices.*configure +0
-0
configure unset CLICOLOR_FORCE GREP_OPTIONS · line 15
Quoted 5 lines
configure +2
-0@@ -11,6 +11,51 @@ unset CLICOLOR_FORCE GREP_OPTIONS # Don't allow CCACHE, if present, to use cached results of compile tests! export CCACHE_RECACHE=yes +# make source path absolute +source_path=$(cd "$(dirname -- "$0")"; pwd)
Our mails crossed; my 1 comment about CDPATH impacting this is still valid.
configure unset CLICOLOR_FORCE GREP_OPTIONS · line 17
Quoted 2 lines
configure +2
-0+ +if test "$PWD" == "$source_path"
and s/==/=/ for non-bash
configure unset CLICOLOR_FORCE GREP_OPTIONS · line 30
Quoted 13 lines
configure +13
-0+then + echo "Using './build' as the directory for build output" + + MARKER=build/auto-created-by-configure + + if test -e build + then + if test -f $MARKER + then + rm -rf build + else + echo "ERROR: ./build dir already exists and was not previously created by configure" + exit 1
TAB damage.
configure unset CLICOLOR_FORCE GREP_OPTIONS · line 39
Quoted 9 lines
configure +9
-0+ fi + fi + + mkdir build + touch $MARKER + + cat > GNUmakefile <<EOF +# This file is auto-generated by configure to support in-source tree +# 'make' command invokation
invocation
Quoted 5 lines
configure +5
-0+ +ifeq (\$(MAKECMDGOALS),) +recurse: all +endif +
configure unset CLICOLOR_FORCE GREP_OPTIONS · line 54
Quoted 10 lines
configure +10
-0+.NOTPARALLEL: % +%: force + @echo 'changing dir to build for \$(MAKE) "\$(MAKECMDGOALS)"...' + @\$(MAKE) -C build -f Makefile \$(MAKECMDGOALS) + @if test "\$(MAKECMDGOALS)" = "distclean" && test -e build/auto-created-by-configure ; then rm -rf build GNUmakefile ; fi +force: ; +.PHONY: force +GNUmakefile: ; + +EOF
Quote the first EOF to avoid having to quote all $ in the heredoc
Quoted 9 lines
configure +4
-0+ cd build + exec $source_path/configure "$@" +fi + # Temporary directory used for files created while # configure runs. Since it is in the build directory # we can safely blow away any previous version of it
configure ld_has() { · line 347
Quoted 9 lines
configure +0
-3@@ -297,9 +342,6 @@ ld_has() { $ld --help 2>/dev/null | grep ".$1" >/dev/null 2>&1 } -# make source path absolute -source_path=$(cd "$(dirname -- "$0")"; pwd) - if printf %s\\n "$source_path" "$PWD" | grep -q "[[:space:]:]"; then error_exit "main directory cannot contain spaces nor colons"
With corrections, this is looking good; I'm okay if v3 includes:
Signature · 3 lines
Eric Blake, Principal Software Engineer Red Hat, Inc. +1-919-301-3226 Virtualization: qemu.org | libvirt.org
Quoted 8 lines · Daniel P. Berrangé
Meson requires the build dir to be separate from the source tree. Many people are used to just running "./configure && make" though and the meson conversion breaks that.
This introduces some backcompat support to make it appear as if an "in source tree" build is being done, but with the the results in the "build/" directory. This allows "./configure && make" to work as it did historically, albeit with the output binaries staying under build/.
An observation:
If you already had out-of-tree builds, this does not change anything. You can do an incremental build, where a tree that builds pre-merge should continue to build incrementally with 'make -C dir' post-merge.
If you are used to in-tree builds, and do a fresh checkout, this lets you maintain the illusion of an in-tree build although binaries may be located differently than you are used to.
But if you do an incremental update to an in-tree build, this will cause some odd behaviors, starting with the git update:
$ git merge $paolos_tag error: The following untracked working tree files would be overwritten by merge: accel/kvm/trace.h ... util/trace.h Please move or remove them before you merge. Aborting $ find -name trace.h -delete $ git merge $paolos_tag $ git am $this_patch $ make config-host.mak is out-of-date, running configure Using './build' as the directory for build output Submodule 'meson' (https://github.com/mesonbuild/meson/) registered for path 'meson' Cloning into '/home/eblake/qemu-tmp2/meson'... ... Command line for building ['libcommon.fa'] is long, using a response file ./ninjatool -t ninja2make --omit clean dist uninstall < build.ninja > Makefile.ninja /bin/sh: build.ninja: No such file or directory GEN tests/test-qapi-gen make: Nothing to be done for 'all'. $ echo $? 0 $ make changing dir to build for make ""... make[1]: Entering directory '/home/eblake/qemu-tmp2/build' Makefile:84: *** This is an out of tree build but your source tree (/home/eblake/qemu-tmp2) seems to have been used for an in-tree build. You can fix this by running "make distclean && rm -rf *-linux-user *-softmmu" in your source tree. Stop. make[1]: Leaving directory '/home/eblake/qemu-tmp2/build' make: *** [GNUmakefile:11: all] Error 2 $ echo $? 2
So I'm not sure why the first build gets as far as it does, but does NOT complete things and yet does not fail make, but my advice is that you should NOT try to an incremental build on in-tree build when crossing the meson epoch. If you are a fan of in-tree convenience, you need a ONE-TIME distclean when pulling in these changes (the fact that you HAVE to clean up trace.h files to merge in the meson stuff should be a hint for that). After that has been done, you can go back to pretending meson supports in-tree.
Signature · 3 lines
Eric Blake, Principal Software Engineer Red Hat, Inc. +1-919-301-3226 Virtualization: qemu.org | libvirt.org
Quoted 22 lines · Eric Blake
Quoted 8 lines · Daniel P. Berrangé
Meson requires the build dir to be separate from the source tree. Many people are used to just running "./configure && make" though and the meson conversion breaks that.
This introduces some backcompat support to make it appear as if an "in source tree" build is being done, but with the the results in the "build/" directory. This allows "./configure && make" to work as it did historically, albeit with the output binaries staying under build/.
An observation:
If you already had out-of-tree builds, this does not change anything. You can do an incremental build, where a tree that builds pre-merge should continue to build incrementally with 'make -C dir' post-merge.
If you are used to in-tree builds, and do a fresh checkout, this lets you maintain the illusion of an in-tree build although binaries may be located differently than you are used to.
But if you do an incremental update to an in-tree build, this will cause some odd behaviors, starting with the git update:
snip.
Quoted 7 lines
So I'm not sure why the first build gets as far as it does, but does NOT complete things and yet does not fail make, but my advice is that you should NOT try to an incremental build on in-tree build when crossing the meson epoch. If you are a fan of in-tree convenience, you need a ONE-TIME distclean when pulling in these changes (the fact that you HAVE to clean up
trace.hfiles to merge in the meson stuff should be a hint for that). After that has been done, you can go back to pretending meson supports in-tree.
Yeah, I think that's something we'll have to live with. The amount of extra complexity that would be required to try to make the incremental build work across the meson introduction would be quite large. A more efficient use of time is to just clean the dir manually, rather than debugging some makefile rules that will only be needed once.
Regards,
Daniel
Signature · 3 lines
|: https://berrange.com -o- https://www.flickr.com/photos/dberrange :| |: https://libvirt.org -o- https://fstop138.berrange.com :| |: https://entangle-photo.org -o- https://www.instagram.com/dberrange :|
Am 20.08.2020 um 23:15 hat Eric Blake geschrieben:
Quoted 61 lines · Daniel P. Berrangé
Quoted 8 lines
Meson requires the build dir to be separate from the source tree. Many people are used to just running "./configure && make" though and the meson conversion breaks that.
This introduces some backcompat support to make it appear as if an "in source tree" build is being done, but with the the results in the "build/" directory. This allows "./configure && make" to work as it did historically, albeit with the output binaries staying under build/.
An observation:
If you already had out-of-tree builds, this does not change anything. You can do an incremental build, where a tree that builds pre-merge should continue to build incrementally with 'make -C dir' post-merge.
If you are used to in-tree builds, and do a fresh checkout, this lets you maintain the illusion of an in-tree build although binaries may be located differently than you are used to.
But if you do an incremental update to an in-tree build, this will cause some odd behaviors, starting with the git update:
$ git merge $paolos_tag error: The following untracked working tree files would be overwritten by merge: accel/kvm/trace.h ... util/trace.h Please move or remove them before you merge. Aborting $ find -name trace.h -delete $ git merge $paolos_tag $ git am $this_patch $ make config-host.mak is out-of-date, running configure Using './build' as the directory for build output Submodule 'meson' (https://github.com/mesonbuild/meson/) registered for path 'meson' Cloning into '/home/eblake/qemu-tmp2/meson'... ... Command line for building ['libcommon.fa'] is long, using a response file ./ninjatool -t ninja2make --omit clean dist uninstall < build.ninja > Makefile.ninja /bin/sh: build.ninja: No such file or directory GEN tests/test-qapi-gen make: Nothing to be done for 'all'. $ echo $? 0 $ make changing dir to build for make ""... make[1]: Entering directory '/home/eblake/qemu-tmp2/build' Makefile:84: *** This is an out of tree build but your source tree (/home/eblake/qemu-tmp2) seems to have been used for an in-tree build. You can fix this by running "make distclean && rm -rf *-linux-user *-softmmu" in your source tree. Stop. make[1]: Leaving directory '/home/eblake/qemu-tmp2/build' make: *** [GNUmakefile:11: all] Error 2 $ echo $? 2
Quoted 7 lines
So I'm not sure why the first build gets as far as it does, but does NOT complete things and yet does not fail make, but my advice is that you should NOT try to an incremental build on in-tree build when crossing the meson epoch. If you are a fan of in-tree convenience, you need a ONE-TIME distclean when pulling in these changes (the fact that you HAVE to clean up
trace.hfiles to merge in the meson stuff should be a hint for that). After that has been done, you can go back to pretending meson supports in-tree.
Sounds like it will be painful to switch between branches based on make and branches based on meson. By extension, it will also be painful to check out and build old versions for comparison, or doing that even more than once during git bisect. :-(
Kevin
Quoted 11 lines · Kevin Wolf
Quoted 7 lines
So I'm not sure why the first build gets as far as it does, but does NOT complete things and yet does not fail make, but my advice is that you should NOT try to an incremental build on in-tree build when crossing the meson epoch. If you are a fan of in-tree convenience, you need a ONE-TIME distclean when pulling in these changes (the fact that you HAVE to clean up
trace.hfiles to merge in the meson stuff should be a hint for that). After that has been done, you can go back to pretending meson supports in-tree.Sounds like it will be painful to switch between branches based on make and branches based on meson. By extension, it will also be painful to check out and build old versions for comparison, or doing that even more than once during git bisect. :-(
Not if you switch to out-of-tree builds...
Paolo
Am 21.08.2020 um 12:15 hat Paolo Bonzini geschrieben:
Quoted 8 lines · Kevin Wolf
Quoted 7 lines
Quoted 7 lines
So I'm not sure why the first build gets as far as it does, but does NOT complete things and yet does not fail make, but my advice is that you should NOT try to an incremental build on in-tree build when crossing the meson epoch. If you are a fan of in-tree convenience, you need a ONE-TIME distclean when pulling in these changes (the fact that you HAVE to clean up
trace.hfiles to merge in the meson stuff should be a hint for that). After that has been done, you can go back to pretending meson supports in-tree.
Quoted 6 lines
Quoted 4 lines
Sounds like it will be painful to switch between branches based on make and branches based on meson. By extension, it will also be painful to check out and build old versions for comparison, or doing that even more than once during git bisect. :-(
Not if you switch to out-of-tree builds...
I don't see what out-of-tree builds change about this unless I delete and reconfigure them after each step? Even in those cases where I use out-of-tree builds, I often reuse the same directory.
Kevin
Quoted 8 lines · Kevin Wolf
Quoted 5 lines
Quoted 4 lines
Sounds like it will be painful to switch between branches based on make and branches based on meson. By extension, it will also be painful to check out and build old versions for comparison, or doing that even more than once during git bisect. :-(
Not if you switch to out-of-tree builds...
I don't see what out-of-tree builds change about this unless I delete and reconfigure them after each step? Even in those cases where I use out-of-tree builds, I often reuse the same directory.
In two ways:
1) bisection will rarely jump around the point where Meson was introduced. First, because if it coincides with the 5.1.0 release, then you know in advance if the problem was introduced before or after the merge. Second, because the bisection will quickly land on a merge commit, and then you can (just for going down the merged branch) use a separate out-of-tree build directory.
2) for the rare case of working on a branch that was developed pre-Meson and has not been rebased (or need not be rebased), you again use a separate out-of-tree build directory just for that one, and you don't have to worry about doing distclean or an incremental builds.
Paolo
Quoted 70 lines · Kevin Wolf
Am 20.08.2020 um 23:15 hat Eric Blake geschrieben:
Quoted 61 lines · Daniel P. Berrangé
Quoted 8 lines
Meson requires the build dir to be separate from the source tree. Many people are used to just running "./configure && make" though and the meson conversion breaks that.
This introduces some backcompat support to make it appear as if an "in source tree" build is being done, but with the the results in the "build/" directory. This allows "./configure && make" to work as it did historically, albeit with the output binaries staying under build/.
An observation:
If you already had out-of-tree builds, this does not change anything. You can do an incremental build, where a tree that builds pre-merge should continue to build incrementally with 'make -C dir' post-merge.
If you are used to in-tree builds, and do a fresh checkout, this lets you maintain the illusion of an in-tree build although binaries may be located differently than you are used to.
But if you do an incremental update to an in-tree build, this will cause some odd behaviors, starting with the git update:
$ git merge $paolos_tag error: The following untracked working tree files would be overwritten by merge: accel/kvm/trace.h ... util/trace.h Please move or remove them before you merge. Aborting $ find -name trace.h -delete $ git merge $paolos_tag $ git am $this_patch $ make config-host.mak is out-of-date, running configure Using './build' as the directory for build output Submodule 'meson' (https://github.com/mesonbuild/meson/) registered for path 'meson' Cloning into '/home/eblake/qemu-tmp2/meson'... ... Command line for building ['libcommon.fa'] is long, using a response file ./ninjatool -t ninja2make --omit clean dist uninstall < build.ninja > Makefile.ninja /bin/sh: build.ninja: No such file or directory GEN tests/test-qapi-gen make: Nothing to be done for 'all'. $ echo $? 0 $ make changing dir to build for make ""... make[1]: Entering directory '/home/eblake/qemu-tmp2/build' Makefile:84: *** This is an out of tree build but your source tree (/home/eblake/qemu-tmp2) seems to have been used for an in-tree build. You can fix this by running "make distclean && rm -rf *-linux-user *-softmmu" in your source tree. Stop. make[1]: Leaving directory '/home/eblake/qemu-tmp2/build' make: *** [GNUmakefile:11: all] Error 2 $ echo $? 2Quoted 7 lines
So I'm not sure why the first build gets as far as it does, but does NOT complete things and yet does not fail make, but my advice is that you should NOT try to an incremental build on in-tree build when crossing the meson epoch. If you are a fan of in-tree convenience, you need a ONE-TIME distclean when pulling in these changes (the fact that you HAVE to clean up
trace.hfiles to merge in the meson stuff should be a hint for that). After that has been done, you can go back to pretending meson supports in-tree.
Quoted 4 lines
Sounds like it will be painful to switch between branches based on make and branches based on meson. By extension, it will also be painful to check out and build old versions for comparison, or doing that even more than once during git bisect. :-(
Such is life when using in-source-dir builds.
Even with our current build system, using a separate build directory makes it easier to work across multiple branches, as you can trivially keep the builds from each branch separate and they won't interfere with each other.
Regards,
Daniel
Signature · 3 lines
|: https://berrange.com -o- https://www.flickr.com/photos/dberrange :| |: https://libvirt.org -o- https://fstop138.berrange.com :| |: https://entangle-photo.org -o- https://www.instagram.com/dberrange :|
Paolo Bonzini
AppliedQuoted 120 lines · Daniel P. Berrangé
Meson requires the build dir to be separate from the source tree. Many people are used to just running "./configure && make" though and the meson conversion breaks that.
This introduces some backcompat support to make it appear as if an "in source tree" build is being done, but with the the results in the "build/" directory. This allows "./configure && make" to work as it did historically, albeit with the output binaries staying under build/.
Signed-off-by Daniel P. Berrangé <[email protected]>---
This is a simple integration of Eric's proposal from
https://lists.gnu.org/archive/html/qemu-devel/2020-03/msg07290.html
with a bit of configure magic. It is enough to enable
./configure
make
make checkI've not tested it beyond that. Note it blows away the "build/" dir each time ./configure is run so it is pristine each time.
We could optionally symlink binaries from build/ into $PWD if people think that is important, eg by changing GNUmakefile to have:
recurse: all
for bin in `find build -maxdepth 1 -type f -executable | grep -v -E '(ninjatool|config.status)'`; \ do \ ln -f -s $$bin . ; \ doneand some cleanup logic to purge the symlinks for "make clean"
This goes on top of Paolo's most recent meson port v175 posting, or whatever number it is upto now :-)
In v2:
- Use a marker file so we don't blow away a build/ dir we didn't create
- Silence the distclean rule
- Fix broken use oferror_exitthat's not defined yet
- Add comment to GNUmakefile.gitignore | 2 ++ configure | 48 +++++++++++++++++++++++++++++++++++++++++++++--- 2 files changed, 47 insertions(+), 3 deletions(-).gitignore +2
-0@@ -1,3 +1,5 @@ +/GNUmakefile +/build/ /.doctrees /config-devices.* /config-all-devices.*configure +45
-0@@ -11,6 +11,51 @@ unset CLICOLOR_FORCE GREP_OPTIONS # Don't allow CCACHE, if present, to use cached results of compile tests! export CCACHE_RECACHE=yes +# make source path absolute +source_path=$(cd "$(dirname -- "$0")"; pwd) + +if test "$PWD" == "$source_path" +then + echo "Using './build' as the directory for build output" + + MARKER=build/auto-created-by-configure + + if test -e build + then + if test -f $MARKER + then + rm -rf build + else + echo "ERROR: ./build dir already exists and was not previously created by configure" + exit 1 + fi + fi + + mkdir build + touch $MARKER + + cat > GNUmakefile <<EOF +# This file is auto-generated by configure to support in-source tree +# 'make' command invokation + +ifeq (\$(MAKECMDGOALS),) +recurse: all +endif + +.NOTPARALLEL: % +%: force + @echo 'changing dir to build for \$(MAKE) "\$(MAKECMDGOALS)"...' + @\$(MAKE) -C build -f Makefile \$(MAKECMDGOALS) + @if test "\$(MAKECMDGOALS)" = "distclean" && test -e build/auto-created-by-configure ; then rm -rf build GNUmakefile ; fi +force: ; +.PHONY: force +GNUmakefile: ; + +EOF + cd build + exec $source_path/configure "$@" +fi + # Temporary directory used for files created while # configure runs. Since it is in the build directory # we can safely blow away any previous version of it
configure ld_has() { · line 347
Quoted 9 lines
configure +0
-3@@ -297,9 +342,6 @@ ld_has() { $ld --help 2>/dev/null | grep ".$1" >/dev/null 2>&1 } -# make source path absolute -source_path=$(cd "$(dirname -- "$0")"; pwd) - if printf %s\\n "$source_path" "$PWD" | grep -q "[[:space:]:]"; then error_exit "main directory cannot contain spaces nor colons"
Queued, thanks!
Paolo
Am 20.08.2020 um 19:31 hat Daniel P. Berrangé geschrieben:
Quoted 16 lines
Meson requires the build dir to be separate from the source tree. Many people are used to just running "./configure && make" though and the meson conversion breaks that.
This introduces some backcompat support to make it appear as if an "in source tree" build is being done, but with the the results in the "build/" directory. This allows "./configure && make" to work as it did historically, albeit with the output binaries staying under build/.
Signed-off-by Daniel P. Berrangé <[email protected]>---
This is a simple integration of Eric's proposal from
https://lists.gnu.org/archive/html/qemu-devel/2020-03/msg07290.html
Quoted 8 lines
with a bit of configure magic. It is enough to enable
./configure
make
make checkI've not tested it beyond that. Note it blows away the "build/" dir each time ./configure is run so it is pristine each time.
I guess "make install" is the only other one that normal users would care about. We shoud make sure that it works (I don't see why it wouldn't, but worth testing anyway).
Kevin
Quoted 23 lines · Kevin Wolf
Am 20.08.2020 um 19:31 hat Daniel P. Berrangé geschrieben:
Quoted 22 lines
Meson requires the build dir to be separate from the source tree. Many people are used to just running "./configure && make" though and the meson conversion breaks that.
This introduces some backcompat support to make it appear as if an "in source tree" build is being done, but with the the results in the "build/" directory. This allows "./configure && make" to work as it did historically, albeit with the output binaries staying under build/.
Signed-off-by Daniel P. Berrangé <[email protected]>---
This is a simple integration of Eric's proposal from
https://lists.gnu.org/archive/html/qemu-devel/2020-03/msg07290.html
with a bit of configure magic. It is enough to enable
./configure
make
make check
Quoted 6 lines
Quoted 2 lines
I've not tested it beyond that. Note it blows away the "build/" dir each time ./configure is run so it is pristine each time.
I guess "make install" is the only other one that normal users would care about. We shoud make sure that it works (I don't see why it wouldn't, but worth testing anyway).
I've just tested "make instal DESTDIR=pwd/vroot" in order to validate that variables are passed through too, and it appears to be succesful.
$ make install DESTDIR=`pwd`/vroot ...snip... $ find vroot/ | head -30 vroot/ vroot/usr vroot/usr/local vroot/usr/local/bin vroot/usr/local/bin/qemu-nbd vroot/usr/local/bin/qemu-keymap vroot/usr/local/bin/qemu-pr-helper vroot/usr/local/bin/qemu-storage-daemon vroot/usr/local/bin/elf2dmp vroot/usr/local/bin/qemu-img vroot/usr/local/bin/qemu-edid vroot/usr/local/bin/qemu-system-x86_64 vroot/usr/local/bin/qemu-ga vroot/usr/local/bin/qemu-io vroot/usr/local/var vroot/usr/local/var/run vroot/usr/local/libexec vroot/usr/local/libexec/vhost-user-gpu vroot/usr/local/libexec/qemu-bridge-helper vroot/usr/local/libexec/virtfs-proxy-helper vroot/usr/local/libexec/virtiofsd vroot/usr/local/share vroot/usr/local/share/icons vroot/usr/local/share/icons/hicolor vroot/usr/local/share/icons/hicolor/256x256 vroot/usr/local/share/icons/hicolor/256x256/apps vroot/usr/local/share/icons/hicolor/256x256/apps/qemu.png vroot/usr/local/share/icons/hicolor/48x48 vroot/usr/local/share/icons/hicolor/48x48/apps vroot/usr/local/share/icons/hicolor/48x48/apps/qemu.png ...snip...
Regards,
Daniel
Signature · 3 lines
|: https://berrange.com -o- https://www.flickr.com/photos/dberrange :| |: https://libvirt.org -o- https://fstop138.berrange.com :| |: https://entangle-photo.org -o- https://www.instagram.com/dberrange :|