Skip to contentSkip to conversation

acpi/pwm/i915: Convert pwm-crc and i915 driver's PWM code to use the atomic PWM API

PATCH Superseded Hans de Goede 3 participants 21 messages Aug 24, 2020

Subsystems (6)

v6 of 10 Superseded Latest is v10 →

lore
Share & tools
lore
#0 lore raw

v6 cover acpi/pwm/i915: Convert pwm-crc and i915 driver's PWM code to use the atomic PWM API

Hi All,

Here is v6 of my patch series converting the i915 driver's code for controlling the panel's backlight with an external PWM controller to use the atomic PWM API. See below for the changelog.

This version of the series has been rebased on 5.9-rc1 and has a Reviewed-by or Acked-by for all patches.

The main purpose of sending this new version out is to allow the intel-gfx CI to play with it.

As discussed before, because of interdependencies of the patches I plan to push the entire series to drm-intel-next-queued once it has passed CI.

Thierry, I believe from our previous discussion that you are ok with pushing the pwm-crc and pwm-lpss patches through the drm-intel tree, but you have not given your Acked-by for this. If you are not ok with me pushing these out this way please let me now ASAP. If you are ok with this an Acked-by would be appreciated.

This series has been tested (and re-tested after adding various bug-fixes) extensively. It has been tested on the following devices:

-Asus T100TA BYT + CRC-PMIC PWM
-Toshiba WT8-A BYT + CRC-PMIC PWM -Thundersoft TS178 BYT + CRC-PMIC PWM, inverse PWM -Asus T100HA CHT + CRC-PMIC PWM
-Terra Pad 1061 BYT + LPSS PWM
-Trekstor Twin 10.1 BYT + LPSS PWM
-Asus T101HA CHT + CRC-PMIC PWM
-GPD Pocket CHT + CRC-PMIC PWM

Regards,

Hans

Changelog:

Changes in v6:
- Rebase on v5.9-rc1
- Adjust pwm-crc patches for pwm_state.period and .duty_cycle now being u64

Changes in v5:
- Dropped the "pwm: lpss: Correct get_state result for base_unit == 0" patch. The base_unit == 0 condition should never happen and sofar it is unclear what the proper behavior / correct values to store in the pwm_state should be when this does happen. Since this patch was added as an extra pwm-lpss fix in v4 of this patch-set and otherwise is orthogonal to the of this patch-set just drop it (again).
- "[PATCH 04/16] pwm: lpss: Add range limit check for the base_unit register value"
- Use clamp_val(... instead of clam_t(unsigned long long, ...
- "[PATCH 05/16] pwm: lpss: Add pwm_lpss_prepare_enable() helper"
- This is a new patch in v5 of this patchset
- [PATCH 06/16] pwm: lpss: Use pwm_lpss_apply() when restoring state on resume
- Use the new pwm_lpss_prepare_enable() helper

Changes in v4:
- "[PATCH v4 06/16] pwm: lpss: Correct get_state result for base_unit == 0"
- This is a new patch in v4 of this patchset
- "[PATCH v4 12/16] pwm: crc: Implement get_state() method"
- Use DIV_ROUND_UP when calculating the period and duty_cycle values
- "[PATCH v4 16/16] drm/i915: panel: Use atomic PWM API for devs with an external PWM controller"
- Add a note to the commit message about the changes in pwm_disable_backlight()
- Use the pwm_set/get_relative_duty_cycle() helpers

Changes in v3:
- "[PATCH v3 04/15] pwm: lpss: Add range limit check for the base_unit register value"
- Use base_unit_range - 1 as maximum value for the clamp()
- "[PATCH v3 05/15] pwm: lpss: Use pwm_lpss_apply() when restoring state on resume"
- This replaces the "pwm: lpss: Set SW_UPDATE bit when enabling the PWM" patch from previous versions of this patch-set, which really was a hack working around the resume issue which this patch fixes properly.
- PATCH v3 6 - 11 pwm-crc changes:
- Various small changes resulting from the reviews by Andy and Uwe, including some refactoring of the patches to reduce the amount of churn in the patch-set

Changes in v2:
- Fix coverletter subject
- Drop accidentally included debugging patch
- "[PATCH v3 02/15] ACPI / LPSS: Save Cherry Trail PWM ctx registers only once (
- Move #define LPSS_SAVE_CTX_ONCE define to group it with LPSS_SAVE_CTX

#1 lore raw

PATCH v6 1/16 ACPI / LPSS: Resume Cherry Trail PWM controller in no-irq phase

The DSDTs on most Cherry Trail devices have an ugly clutch where the PWM controller gets poked from the _PS0 method of the graphics-card device:

	Local0 = PSAT /* \_SB_.PCI0.GFX0.PSAT */
	If (((Local0 & 0x03) == 0x03))
	{
	    PSAT &= 0xFFFFFFFC
	    Local1 = PSAT /* \_SB_.PCI0.GFX0.PSAT */
	    RSTA = Zero
	    RSTF = Zero
	    RSTA = One
	    RSTF = One
	    PWMB |= 0xC0000000
	    PWMC = PWMB /* \_SB_.PCI0.GFX0.PWMB */
	}

Where PSAT is the power-status register of the PWM controller, so if it is in D3 when the GFX0 device's PS0 method runs then it will turn it on and restore the PWM ctrl register value it saved from its PS3 handler. Note not only does it restore it, it ors it with 0xC0000000 turning it on at a time where we may not want it to get turned on at all.

The pwm_get call which the i915 driver does to get a reference to the PWM controller, already adds a device-link making the GFX0 device a consumer of the PWM device. So it should already have been resumed when the above AML runs and the AML should thus not do its undesirable poking of the PWM controller register.

But the PCI core powers on PCI devices in the no-irq resume phase and thus calls the troublesome PS0 method in the no-irq resume phase. Where as LPSS devices by default are resumed in the early resume phase.

This commit sets the resume_from_noirq flag in the bsw_pwm_dev_desc struct, so that Cherry Trail PWM controllers will be resumed in the no-irq phase. Together with the device-link added by the pwm-get this ensures that the PWM controller will be on when the troublesome PS0 method runs, which stops it from poking the PWM controller.

---
 drivers/acpi/acpi_lpss.c | 1 +
 1 file changed, 1 insertion(+)
drivers/acpi/acpi_lpss.c +1 -0
index 5e2bfbcf526f..67892fc0b822 100644
@@ -257,6 +257,7 @@ static const struct lpss_device_desc bsw_pwm_dev_desc = {
 	.flags = LPSS_SAVE_CTX | LPSS_NO_D3_DELAY,
 	.prv_offset = 0x800,
 	.setup = bsw_pwm_setup,
+	.resume_from_noirq = true,
 };
 
 static const struct lpss_device_desc byt_uart_dev_desc = {
Signature · 1 line
2.28.0
#2 lore raw

PATCH v6 2/16 ACPI / LPSS: Save Cherry Trail PWM ctx registers only once (at activation)

In reply to Hans de Goede

The DSDTs on most Cherry Trail devices have an ugly clutch where the PWM controller gets turned off from the _PS3 method of the graphics-card dev:

            Method (_PS3, 0, Serialized)  // _PS3: Power State 3
            {
                ...
                            PWMB = PWMC /* \_SB_.PCI0.GFX0.PWMC */
                            PSAT |= 0x03
                            Local0 = PSAT /* \_SB_.PCI0.GFX0.PSAT */
                ...
            }

Where PSAT is the power-status register of the PWM controller.

Since the i915 driver will do a pwm_get on the pwm device as it uses it to control the LCD panel backlight, there is a device-link marking the i915 device as a consumer of the pwm device. So that the PWM controller will always be suspended after the i915 driver suspends (which is the right thing to do). This causes the above GFX0 PS3 AML code to run before acpi_lpss.c calls acpi_lpss_save_ctx().

So on these devices the PWM controller will already be off when acpi_lpss_save_ctx() runs. This causes it to read/save all 1-s (0xffffffff) as ctx register values.

When these bogus values get restored on resume the PWM controller actually keeps working, since most bits are reserved, but this does set bit 3 of the LPSS General purpose register, which for the PWM controller has the following function: "This bit is re-used to support 32kHz slow mode. Default is 19.2MHz as PWM source clock".

This causes the clock of the PWM controller to switch from 19.2MHz to 32KHz, which is a slow-down of a factor 600. Surprisingly enough so far there have been few bug reports about this. This is likely because the i915 driver was hardcoding the PWM frequency to 46 KHz, which divided by 600 would result in a PWM frequency of approx. 78 Hz, which mostly still works fine. There are some bug reports about the LCD backlight flickering after suspend/resume which are likely caused by this issue.

But with the upcoming patch-series to finally switch the i915 drivers code for external PWM controllers to use the atomic API and to honor the PWM frequency specified in the video BIOS (VBT), this becomes a much bigger problem. On most cases the VBT specifies either 200 Hz or 20 KHz as PWM frequency, which with the mentioned issue ends up being either 1/3 Hz, where the backlight actually visible blinks on and off every 3s, or in 33 Hz and horrible flickering of the backlight.

There are a number of possible solutions to this problem:

1. Make acpi_lpss_save_ctx() run before GFX0._PS3
Pro: Clean solution from pov of not medling with save/restore ctx code
Con: As mentioned the current ordering is the right thing to do
Con: Requires assymmetry in at what suspend/resume phase we do the save vs
restore, requiring more suspend/resume ordering hacks in already convoluted acpi_lpss.c suspend/resume code.
2. Do some sort of save once mode for the LPSS ctx
Pro: Reasonably clean
Con: Needs a new LPSS flag + code changes to handle the flag
3. Detect we have failed to save the ctx registers and do not restore them
Pro: Not PWM specific, might help with issues on other LPSS devices too
Con: If we can get away with not restoring the ctx why bother with it at
all?
4. Do not save the ctx for CHT PWM controllers
Pro: Clean, as simple as dropping a flag?
Con: Not so simple as dropping a flag, needs a new flag to ensure that
we still do lpss_deassert_reset() on device activation.
5. Make the pwm-lpss code fixup the LPSS-context registers
Pro: Keeps acpi_lpss.c code clean
Con: Moves knowledge of LPSS-context into the pwm-lpss.c code

1 and 5 both do not seem to be a desirable way forward.

3 and 4 seem ok, but they both assume that restoring the LPSS-context registers is not necessary. I have done a couple of test and those do show that restoring the LPSS-context indeed does not seem to be necessary on devices using s2idle suspend (and successfully reaching S0i3). But I have no hardware to test deep / S3 suspend. So I'm not sure that not restoring the context is safe.

That leaves solution 2, which is about as simple / clean as 3 and 4, so this commit fixes the described problem by implementing a new LPSS_SAVE_CTX_ONCE flag and setting that for the CHT PWM controllers.

---
Changes in v2:
- Move #define LPSS_SAVE_CTX_ONCE define to group it with LPSS_SAVE_CTX

---
 drivers/acpi/acpi_lpss.c | 21 +++++++++++++++++----
 1 file changed, 17 insertions(+), 4 deletions(-)
drivers/acpi/acpi_lpss.c +17 -4
index 67892fc0b822..a8d7d83ac761 100644
@@ -67,7 +67,15 @@ ACPI_MODULE_NAME("acpi_lpss");
 #define LPSS_CLK_DIVIDER		BIT(2)
 #define LPSS_LTR			BIT(3)
 #define LPSS_SAVE_CTX			BIT(4)
-#define LPSS_NO_D3_DELAY		BIT(5)
+/*
+ * For some devices the DSDT AML code for another device turns off the device
+ * before our suspend handler runs, causing us to read/save all 1-s (0xffffffff)
+ * as ctx register values.
+ * Luckily these devices always use the same ctx register values, so we can
+ * work around this by saving the ctx registers once on activation.
+ */
+#define LPSS_SAVE_CTX_ONCE		BIT(5)
+#define LPSS_NO_D3_DELAY		BIT(6)
 
 struct lpss_private_data;
 
@@ -254,7 +262,7 @@ static const struct lpss_device_desc byt_pwm_dev_desc = {
 };
 
 static const struct lpss_device_desc bsw_pwm_dev_desc = {
-	.flags = LPSS_SAVE_CTX | LPSS_NO_D3_DELAY,
+	.flags = LPSS_SAVE_CTX_ONCE | LPSS_NO_D3_DELAY,
 	.prv_offset = 0x800,
 	.setup = bsw_pwm_setup,
 	.resume_from_noirq = true,
@@ -885,9 +893,14 @@ static int acpi_lpss_activate(struct device *dev)
 	 * we have to deassert reset line to be sure that ->probe() will
 	 * recognize the device.
 	 */
-	if (pdata->dev_desc->flags & LPSS_SAVE_CTX)
+	if (pdata->dev_desc->flags & (LPSS_SAVE_CTX | LPSS_SAVE_CTX_ONCE))
 		lpss_deassert_reset(pdata);
 
+#ifdef CONFIG_PM
+	if (pdata->dev_desc->flags & LPSS_SAVE_CTX_ONCE)
+		acpi_lpss_save_ctx(dev, pdata);
+#endif
+
 	return 0;
 }
 
@@ -1031,7 +1044,7 @@ static int acpi_lpss_resume(struct device *dev)
 
 	acpi_lpss_d3_to_d0_delay(pdata);
 
-	if (pdata->dev_desc->flags & LPSS_SAVE_CTX)
+	if (pdata->dev_desc->flags & (LPSS_SAVE_CTX | LPSS_SAVE_CTX_ONCE))
 		acpi_lpss_restore_ctx(dev, pdata);
 
 	return 0;
Signature · 6 lines
2.28.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#3 lore raw

PATCH v6 3/16 pwm: lpss: Fix off by one error in base_unit math in pwm_lpss_prepare()

In reply to Hans de Goede

According to the data-sheet the way the PWM controller works is that each input clock-cycle the base_unit gets added to a N bit counter and that counter overflowing determines the PWM output frequency.

So assuming e.g. a 16 bit counter this means that if base_unit is set to 1, after 65535 input clock-cycles the counter has been increased from 0 to 65535 and it will overflow on the next cycle, so it will overflow after every 65536 clock cycles and thus the calculations done in pwm_lpss_prepare() should use 65536 and not 65535.

This commit fixes this. Note this also aligns the calculations in pwm_lpss_prepare() with those in pwm_lpss_get_state().

Note this effectively reverts commit 684309e5043e ("pwm: lpss: Avoid potential overflow of base_unit"). The next patch in this series really fixes the potential overflow of the base_unit value.

Fixes 684309e5043e ("pwm: lpss: Avoid potential overflow of base_unit")

---
Changes in v3:
- Add Fixes tag
- Add Reviewed-by: Andy Shevchenko tag

---
 drivers/pwm/pwm-lpss.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/pwm/pwm-lpss.c +3 -3
index 9d965ffe66d1..43b1fc634af1 100644
@@ -93,7 +93,7 @@ static void pwm_lpss_prepare(struct pwm_lpss_chip *lpwm, struct pwm_device *pwm,
 	 * The equation is:
 	 * base_unit = round(base_unit_range * freq / c)
 	 */
-	base_unit_range = BIT(lpwm->info->base_unit_bits) - 1;
+	base_unit_range = BIT(lpwm->info->base_unit_bits);
 	freq *= base_unit_range;
 
 	base_unit = DIV_ROUND_CLOSEST_ULL(freq, c);
@@ -104,8 +104,8 @@ static void pwm_lpss_prepare(struct pwm_lpss_chip *lpwm, struct pwm_device *pwm,
 
 	orig_ctrl = ctrl = pwm_lpss_read(pwm);
 	ctrl &= ~PWM_ON_TIME_DIV_MASK;
-	ctrl &= ~(base_unit_range << PWM_BASE_UNIT_SHIFT);
-	base_unit &= base_unit_range;
+	ctrl &= ~((base_unit_range - 1) << PWM_BASE_UNIT_SHIFT);
+	base_unit &= (base_unit_range - 1);
 	ctrl |= (u32) base_unit << PWM_BASE_UNIT_SHIFT;
 	ctrl |= on_time_div;
 
Signature · 6 lines
2.28.0

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#4 lore raw

PATCH v6 4/16 pwm: lpss: Add range limit check for the base_unit register value

In reply to Hans de Goede

When the user requests a high enough period ns value, then the calculations in pwm_lpss_prepare() might result in a base_unit value of 0.

But according to the data-sheet the way the PWM controller works is that each input clock-cycle the base_unit gets added to a N bit counter and that counter overflowing determines the PWM output frequency. Adding 0 to the counter is a no-op. The data-sheet even explicitly states that writing 0 to the base_unit bits will result in the PWM outputting a continuous 0 signal.

When the user requestes a low enough period ns value, then the calculations in pwm_lpss_prepare() might result in a base_unit value which is bigger then base_unit_range - 1. Currently the codes for this deals with this by applying a mask:

	base_unit &= (base_unit_range - 1);

But this means that we let the value overflow the range, we throw away the higher bits and store whatever value is left in the lower bits into the register leading to a random output frequency, rather then clamping the output frequency to the highest frequency which the hardware can do.

This commit fixes both issues by clamping the base_unit value to be between 1 and (base_unit_range - 1).

Fixes 684309e5043e ("pwm: lpss: Avoid potential overflow of base_unit")

---
Changes in v5:
- Use clamp_val(... instead of clam_t(unsigned long long, ...

Changes in v3:
- Change upper limit of clamp to (base_unit_range - 1)
- Add Fixes tag

---
 drivers/pwm/pwm-lpss.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/pwm/pwm-lpss.c +2 -1
index 43b1fc634af1..da9bc3d10104 100644
@@ -97,6 +97,8 @@ static void pwm_lpss_prepare(struct pwm_lpss_chip *lpwm, struct pwm_device *pwm,
 	freq *= base_unit_range;
 
 	base_unit = DIV_ROUND_CLOSEST_ULL(freq, c);
+	/* base_unit must not be 0 and we also want to avoid overflowing it */
+	base_unit = clamp_val(base_unit, 1, base_unit_range - 1);
 
 	on_time_div = 255ULL * duty_ns;
 	do_div(on_time_div, period_ns);
@@ -105,7 +107,6 @@ static void pwm_lpss_prepare(struct pwm_lpss_chip *lpwm, struct pwm_device *pwm,
 	orig_ctrl = ctrl = pwm_lpss_read(pwm);
 	ctrl &= ~PWM_ON_TIME_DIV_MASK;
 	ctrl &= ~((base_unit_range - 1) << PWM_BASE_UNIT_SHIFT);
-	base_unit &= (base_unit_range - 1);
 	ctrl |= (u32) base_unit << PWM_BASE_UNIT_SHIFT;
 	ctrl |= on_time_div;
 
Signature · 6 lines
2.28.0

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#5 lore raw

PATCH v6 5/16 pwm: lpss: Add pwm_lpss_prepare_enable() helper

In reply to Hans de Goede

In the not-enabled -> enabled path pwm_lpss_apply() needs to get a runtime-pm reference; and then on any errors it needs to release it again.

This leads to somewhat hard to read code. This commit introduces a new pwm_lpss_prepare_enable() helper and moves all the steps necessary for the not-enabled -> enabled transition there, so that we can error check the entire transition in a single place and only have one pm_runtime_put() on failure call site.

While working on this I noticed that the enabled -> enabled (update settings) path was quite similar, so I've added an enable parameter to the new pwm_lpss_prepare_enable() helper, which allows using it in that path too.

---
 drivers/pwm/pwm-lpss.c | 45 ++++++++++++++++++++++++------------------
 1 file changed, 26 insertions(+), 19 deletions(-)
drivers/pwm/pwm-lpss.c +26 -19
index da9bc3d10104..8a136ba2a583 100644
@@ -122,41 +122,48 @@ static inline void pwm_lpss_cond_enable(struct pwm_device *pwm, bool cond)
 		pwm_lpss_write(pwm, pwm_lpss_read(pwm) | PWM_ENABLE);
 }
 
+static int pwm_lpss_prepare_enable(struct pwm_lpss_chip *lpwm,
+				   struct pwm_device *pwm,
+				   const struct pwm_state *state,
+				   bool enable)
+{
+	int ret;
+
+	ret = pwm_lpss_is_updating(pwm);
+	if (ret)
+		return ret;
+
+	pwm_lpss_prepare(lpwm, pwm, state->duty_cycle, state->period);
+	pwm_lpss_cond_enable(pwm, enable && lpwm->info->bypass == false);
+	ret = pwm_lpss_wait_for_update(pwm);
+	if (ret)
+		return ret;
+
+	pwm_lpss_cond_enable(pwm, enable && lpwm->info->bypass == true);
+	return 0;
+}
+
 static int pwm_lpss_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 			  const struct pwm_state *state)
 {
 	struct pwm_lpss_chip *lpwm = to_lpwm(chip);
-	int ret;
+	int ret = 0;
 
 	if (state->enabled) {
 		if (!pwm_is_enabled(pwm)) {
 			pm_runtime_get_sync(chip->dev);
-			ret = pwm_lpss_is_updating(pwm);
-			if (ret) {
-				pm_runtime_put(chip->dev);
-				return ret;
-			}
-			pwm_lpss_prepare(lpwm, pwm, state->duty_cycle, state->period);
-			pwm_lpss_cond_enable(pwm, lpwm->info->bypass == false);
-			ret = pwm_lpss_wait_for_update(pwm);
-			if (ret) {
+			ret = pwm_lpss_prepare_enable(lpwm, pwm, state, true);
+			if (ret)
 				pm_runtime_put(chip->dev);
-				return ret;
-			}
-			pwm_lpss_cond_enable(pwm, lpwm->info->bypass == true);
 		} else {
-			ret = pwm_lpss_is_updating(pwm);
-			if (ret)
-				return ret;
-			pwm_lpss_prepare(lpwm, pwm, state->duty_cycle, state->period);
-			return pwm_lpss_wait_for_update(pwm);
+			ret = pwm_lpss_prepare_enable(lpwm, pwm, state, false);
 		}
 	} else if (pwm_is_enabled(pwm)) {
 		pwm_lpss_write(pwm, pwm_lpss_read(pwm) & ~PWM_ENABLE);
 		pm_runtime_put(chip->dev);
 	}
 
-	return 0;
+	return ret;
 }
 
 static void pwm_lpss_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
Signature · 6 lines
2.28.0

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#6 lore raw

PATCH v6 6/16 pwm: lpss: Use pwm_lpss_apply() when restoring state on resume

In reply to Hans de Goede

Before this commit a suspend + resume of the LPSS PWM controller would result in the controller being reset to its defaults of output-freq = clock/256, duty-cycle=100%, until someone changes to the output-freq and/or duty-cycle are made.

This problem has been masked so far because the main consumer (the i915 driver) was always making duty-cycle changes on resume. With the conversion of the i915 driver to the atomic PWM API the driver now only disables/enables the PWM on suspend/resume leaving the output-freq and duty as is, triggering this problem.

The LPSS PWM controller has a mechanism where the ctrl register value and the actual base-unit and on-time-div values used are latched. When software sets the SW_UPDATE bit then at the end of the current PWM cycle, the new values from the ctrl-register will be latched into the actual registers, and the SW_UPDATE bit will be cleared.

The problem is that before this commit our suspend/resume handling consisted of simply saving the PWM ctrl register on suspend and restoring it on resume, without setting the PWM_SW_UPDATE bit. When the controller has lost its state over a suspend/resume and thus has been reset to the defaults, just restoring the register is not enough. We must also set the SW_UPDATE bit to tell the controller to latch the restored values into the actual registers.

Fixing this problem is not as simple as just or-ing in the value which is being restored with SW_UPDATE. If the PWM was enabled before we must write the new settings + PWM_SW_UPDATE before setting PWM_ENABLE. We must also wait for PWM_SW_UPDATE to become 0 again and depending on the model we must do this either before or after the setting of PWM_ENABLE.

All the necessary logic for doing this is already present inside pwm_lpss_apply(), so instead of duplicating this inside the resume handler, this commit makes the resume handler use pwm_lpss_apply() to restore the settings when necessary. This fixes the output-freq and duty-cycle being reset to their defaults on resume.

---
Changes in v6:
- Add a pwm_lpss_restore_state() helper for re-applying the PWM state on resume

Changes in v5:
- The changes to pwm_lpss_apply() are much cleaner now thanks to the new pwm_lpss_prepare_enable() helper.

Changes in v3:
- This replaces the "pwm: lpss: Set SW_UPDATE bit when enabling the PWM" patch from previous versions of this patch-set, which really was a hack working around the resume issue which this patch fixes properly.

---
 drivers/pwm/pwm-lpss.c | 49 +++++++++++++++++++++++++++++++++++++++---
 1 file changed, 46 insertions(+), 3 deletions(-)
drivers/pwm/pwm-lpss.c +46 -3
index 8a136ba2a583..d77869be053c 100644
@@ -166,6 +166,24 @@ static int pwm_lpss_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 	return ret;
 }
 
+/*
+ * This is a mirror of pwm_lpss_apply() without pm_runtime reference handling
+ * for restoring the PWM state on resume.
+ */
+static int pwm_lpss_restore_state(struct pwm_lpss_chip *lpwm,
+				  struct pwm_device *pwm,
+				  const struct pwm_state *state)
+{
+	int ret = 0;
+
+	if (state->enabled)
+		ret = pwm_lpss_prepare_enable(lpwm, pwm, state, !pwm_is_enabled(pwm));
+	else if (pwm_is_enabled(pwm))
+		pwm_lpss_write(pwm, pwm_lpss_read(pwm) & ~PWM_ENABLE);
+
+	return ret;
+}
+
 static void pwm_lpss_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
 			       struct pwm_state *state)
 {
@@ -278,10 +296,35 @@ EXPORT_SYMBOL_GPL(pwm_lpss_suspend);
 int pwm_lpss_resume(struct device *dev)
 {
 	struct pwm_lpss_chip *lpwm = dev_get_drvdata(dev);
-	int i;
+	struct pwm_state saved_state;
+	struct pwm_device *pwm;
+	int i, ret;
+	u32 ctrl;
 
-	for (i = 0; i < lpwm->info->npwm; i++)
-		writel(lpwm->saved_ctrl[i], lpwm->regs + i * PWM_SIZE + PWM);
+	for (i = 0; i < lpwm->info->npwm; i++) {
+		pwm = &lpwm->chip.pwms[i];
+
+		ctrl = pwm_lpss_read(pwm);
+		/* If we did not reach S0i3/S3 the controller keeps its state */
+		if (ctrl == lpwm->saved_ctrl[i])
+			continue;
+
+		/*
+		 * We cannot just blindly restore the old value here. Since we
+		 * are changing the settings we must set SW_UPDATE and if the
+		 * PWM was enabled before we must write the new settings +
+		 * PWM_SW_UPDATE before setting PWM_ENABLE. We must also wait
+		 * for PWM_SW_UPDATE to become 0 again and depending on the
+		 * model we must do this either before or after the setting of
+		 * PWM_ENABLE.
+		 */
+		saved_state = pwm->state;
+		/* Update enabled to its actual setting after resume */
+		pwm->state.enabled = !!(ctrl & PWM_ENABLE);
+		ret = pwm_lpss_restore_state(lpwm, pwm, &saved_state);
+		if (ret)
+			dev_err(dev, "Error restoring state on resume\n");
+	}
 
 	return 0;
 }
Signature · 6 lines
2.28.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#7 lore raw

PATCH v6 7/16 pwm: crc: Fix period / duty_cycle times being off by a factor of 256

In reply to Hans de Goede

While looking into adding atomic-pwm support to the pwm-crc driver I noticed something odd, there is a PWM_BASE_CLK define of 6 MHz and there is a clock-divider which divides this with a value between 1-128, and there are 256 duty-cycle steps.

The pwm-crc code before this commit assumed that a clock-divider setting of 1 means that the PWM output is running at 6 MHZ, if that is true, where do these 256 duty-cycle steps come from?

This would require an internal frequency of 256 * 6 MHz = 1.5 GHz, that seems unlikely for a PMIC which is using a silicon process optimized for power-switching transistors. It is way more likely that there is an 8 bit counter for the duty cycle which acts as an extra fixed divider wrt the PWM output frequency.

The main user of the pwm-crc driver is the i915 GPU driver which uses it for backlight control. Lets compare the PWM register values set by the video-BIOS (the GOP), assuming the extra fixed divider is present versus the PWM frequency specified in the Video-BIOS-Tables:

Device: PWM Hz set by BIOS PWM Hz specified in VBT
Asus T100TA 200 200
Asus T100HA 200 200
Lenovo Miix 2 8 23437 20000
Toshiba WT8-A 23437 20000

So as we can see if we assume the extra division by 256 then the register values set by the GOP are an exact match for the VBT values, where as otherwise the values would be of by a factor of 256.

This commit fixes the period / duty_cycle calculations to take the extra division by 256 into account.

---
Changes in v3:
- Use NSEC_PER_USEC instead of adding a new (non-sensical) NSEC_PER_MHZ define

---
 drivers/pwm/pwm-crc.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/pwm/pwm-crc.c +3 -3
index 272eeb071147..c056eb9b858c 100644
@@ -21,8 +21,8 @@
 
 #define PWM_MAX_LEVEL		0xFF
 
-#define PWM_BASE_CLK		6000000  /* 6 MHz */
-#define PWM_MAX_PERIOD_NS	21333    /* 46.875KHz */
+#define PWM_BASE_CLK_MHZ	6	/* 6 MHz */
+#define PWM_MAX_PERIOD_NS	5461333	/* 183 Hz */
 
 /**
  * struct crystalcove_pwm - Crystal Cove PWM controller
@@ -72,7 +72,7 @@ static int crc_pwm_config(struct pwm_chip *c, struct pwm_device *pwm,
 
 		/* changing the clk divisor, need to disable fisrt */
 		crc_pwm_disable(c, pwm);
-		clk_div = PWM_BASE_CLK * period_ns / NSEC_PER_SEC;
+		clk_div = PWM_BASE_CLK_MHZ * period_ns / (256 * NSEC_PER_USEC);
 
 		regmap_write(crc_pwm->regmap, PWM0_CLK_DIV,
 					clk_div | PWM_OUTPUT_ENABLE);
Signature · 6 lines
2.28.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#8 lore raw

PATCH v6 8/16 pwm: crc: Fix off-by-one error in the clock-divider calculations

In reply to Hans de Goede

The CRC PWM controller has a clock-divider which divides the clock with a value between 1-128. But as can seen from the PWM_DIV_CLK_xxx defines, this range maps to a register value of 0-127.

So after calculating the clock-divider we must subtract 1 to get the register value, unless the requested frequency was so high that the calculation has already resulted in a (rounded) divider value of 0.

Note that before this fix, setting a period of PWM_MAX_PERIOD_NS which corresponds to the max. divider value of 128 could have resulted in a bug where the code would use 128 as divider-register value which would have resulted in an actual divider value of 0 (and the enable bit being set). A rounding error stopped this bug from actually happen. This same rounding error means that after the subtraction of 1 it is impossible to set the divider to 128. Also bump PWM_MAX_PERIOD_NS by 1 ns to allow setting a divider of 128 (register-value 127).

---
Changes in v3:
- Introduce crc_pwm_calc_clk_div() here instead of later in the patch-set to reduce the amount of churn in the patch-set a bit

---
 drivers/pwm/pwm-crc.c | 17 ++++++++++++++---
 1 file changed, 14 insertions(+), 3 deletions(-)
drivers/pwm/pwm-crc.c +14 -3
index c056eb9b858c..44ec7d5b63e1 100644
@@ -22,7 +22,7 @@
 #define PWM_MAX_LEVEL		0xFF
 
 #define PWM_BASE_CLK_MHZ	6	/* 6 MHz */
-#define PWM_MAX_PERIOD_NS	5461333	/* 183 Hz */
+#define PWM_MAX_PERIOD_NS	5461334	/* 183 Hz */
 
 /**
  * struct crystalcove_pwm - Crystal Cove PWM controller
@@ -39,6 +39,18 @@ static inline struct crystalcove_pwm *to_crc_pwm(struct pwm_chip *pc)
 	return container_of(pc, struct crystalcove_pwm, chip);
 }
 
+static int crc_pwm_calc_clk_div(int period_ns)
+{
+	int clk_div;
+
+	clk_div = PWM_BASE_CLK_MHZ * period_ns / (256 * NSEC_PER_USEC);
+	/* clk_div 1 - 128, maps to register values 0-127 */
+	if (clk_div > 0)
+		clk_div--;
+
+	return clk_div;
+}
+
 static int crc_pwm_enable(struct pwm_chip *c, struct pwm_device *pwm)
 {
 	struct crystalcove_pwm *crc_pwm = to_crc_pwm(c);
@@ -68,11 +80,10 @@ static int crc_pwm_config(struct pwm_chip *c, struct pwm_device *pwm,
 	}
 
 	if (pwm_get_period(pwm) != period_ns) {
-		int clk_div;
+		int clk_div = crc_pwm_calc_clk_div(period_ns);
 
 		/* changing the clk divisor, need to disable fisrt */
 		crc_pwm_disable(c, pwm);
-		clk_div = PWM_BASE_CLK_MHZ * period_ns / (256 * NSEC_PER_USEC);
 
 		regmap_write(crc_pwm->regmap, PWM0_CLK_DIV,
 					clk_div | PWM_OUTPUT_ENABLE);
Signature · 1 line
2.28.0
#9 lore raw

PATCH v6 9/16 pwm: crc: Fix period changes not having any effect

In reply to Hans de Goede

The pwm-crc code is using 2 different enable bits:
1. bit 7 of the PWM0_CLK_DIV (PWM_OUTPUT_ENABLE)
2. bit 0 of the BACKLIGHT_EN register

The BACKLIGHT_EN register at address 0x51 really controls a separate output-only GPIO which is earmarked to be used as output connected to the backlight-enable pin for LCD panels, this GPO is part of the PMIC's "Display Panel Control Block." . This pin should probably be moved over to a GPIO provider driver (and consumers modified accordingly), but that is something for an(other) patch.

Enabling / disabling the actual PWM output is controlled by the PWM_OUTPUT_ENABLE bit of the PWM0_CLK_DIV register.

As the comment in the old code already indicates we must disable the PWM before we can change the clock divider. But the crc_pwm_disable() and crc_pwm_enable() calls the old code make for this only change the BACKLIGHT_EN register; and the value of that register does not matter for changing the period / the divider. What does matter is that the PWM_OUTPUT_ENABLE bit must be cleared before a new value can be written.

This commit modifies crc_pwm_config() to clear PWM_OUTPUT_ENABLE instead when changing the period, so that period changes actually work.

Note this fix will cause a significant behavior change on some devices using the CRC PWM output to drive their backlight. Before the PWM would always run with the output frequency configured by the BIOS at boot, now the period time specified by the i915 driver will actually be honored.

---
 drivers/pwm/pwm-crc.c | 7 ++-----
 1 file changed, 2 insertions(+), 5 deletions(-)
drivers/pwm/pwm-crc.c +2 -5
index 44ec7d5b63e1..81232da0c767 100644
@@ -82,14 +82,11 @@ static int crc_pwm_config(struct pwm_chip *c, struct pwm_device *pwm,
 	if (pwm_get_period(pwm) != period_ns) {
 		int clk_div = crc_pwm_calc_clk_div(period_ns);
 
-		/* changing the clk divisor, need to disable fisrt */
-		crc_pwm_disable(c, pwm);
+		/* changing the clk divisor, clear PWM_OUTPUT_ENABLE first */
+		regmap_write(crc_pwm->regmap, PWM0_CLK_DIV, 0);
 
 		regmap_write(crc_pwm->regmap, PWM0_CLK_DIV,
 					clk_div | PWM_OUTPUT_ENABLE);
-
-		/* enable back */
-		crc_pwm_enable(c, pwm);
 	}
 
 	/* change the pwm duty cycle */
Signature · 6 lines
2.28.0

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#10 lore raw

PATCH v6 10/16 pwm: crc: Enable/disable PWM output on enable/disable

In reply to Hans de Goede

The pwm-crc code is using 2 different enable bits:
1. bit 7 of the PWM0_CLK_DIV (PWM_OUTPUT_ENABLE)
2. bit 0 of the BACKLIGHT_EN register

So far we've kept the PWM_OUTPUT_ENABLE bit set when disabling the PWM, this commit makes crc_pwm_disable() clear it on disable and makes crc_pwm_enable() set it again on re-enable.

---
Changes in v3:
- Remove paragraph about tri-stating the output from the commit message, we don't have a datasheet so this was just an unfounded guess

---
 drivers/pwm/pwm-crc.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/pwm/pwm-crc.c +4 -0
index 81232da0c767..b72008c9b072 100644
@@ -54,7 +54,9 @@ static int crc_pwm_calc_clk_div(int period_ns)
 static int crc_pwm_enable(struct pwm_chip *c, struct pwm_device *pwm)
 {
 	struct crystalcove_pwm *crc_pwm = to_crc_pwm(c);
+	int div = crc_pwm_calc_clk_div(pwm_get_period(pwm));
 
+	regmap_write(crc_pwm->regmap, PWM0_CLK_DIV, div | PWM_OUTPUT_ENABLE);
 	regmap_write(crc_pwm->regmap, BACKLIGHT_EN, 1);
 
 	return 0;
@@ -63,8 +65,10 @@ static int crc_pwm_enable(struct pwm_chip *c, struct pwm_device *pwm)
 static void crc_pwm_disable(struct pwm_chip *c, struct pwm_device *pwm)
 {
 	struct crystalcove_pwm *crc_pwm = to_crc_pwm(c);
+	int div = crc_pwm_calc_clk_div(pwm_get_period(pwm));
 
 	regmap_write(crc_pwm->regmap, BACKLIGHT_EN, 0);
+	regmap_write(crc_pwm->regmap, PWM0_CLK_DIV, div);
 }
 
 static int crc_pwm_config(struct pwm_chip *c, struct pwm_device *pwm,
Signature · 1 line
2.28.0
#11 lore raw

PATCH v6 11/16 pwm: crc: Implement apply() method to support the new atomic PWM API

In reply to Hans de Goede

Replace the enable, disable and config pwm_ops with an apply op, to support the new atomic PWM API.

---
Changes in v6:
- Rebase on 5.9-rc1
- Use do_div when calculating level because pwm_state.period and .duty_cycle are now u64

Changes in v3:
- Keep crc_pwm_calc_clk_div() helper to avoid needless churn

---
 drivers/pwm/pwm-crc.c | 89 ++++++++++++++++++++++++++-----------------
 1 file changed, 54 insertions(+), 35 deletions(-)
drivers/pwm/pwm-crc.c +54 -35
index b72008c9b072..27dc30882424 100644
@@ -51,59 +51,78 @@ static int crc_pwm_calc_clk_div(int period_ns)
 	return clk_div;
 }
 
-static int crc_pwm_enable(struct pwm_chip *c, struct pwm_device *pwm)
+static int crc_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+			 const struct pwm_state *state)
 {
-	struct crystalcove_pwm *crc_pwm = to_crc_pwm(c);
-	int div = crc_pwm_calc_clk_div(pwm_get_period(pwm));
+	struct crystalcove_pwm *crc_pwm = to_crc_pwm(chip);
+	struct device *dev = crc_pwm->chip.dev;
+	int err;
 
-	regmap_write(crc_pwm->regmap, PWM0_CLK_DIV, div | PWM_OUTPUT_ENABLE);
-	regmap_write(crc_pwm->regmap, BACKLIGHT_EN, 1);
+	if (state->period > PWM_MAX_PERIOD_NS) {
+		dev_err(dev, "un-supported period_ns\n");
+		return -EINVAL;
+	}
 
-	return 0;
-}
+	if (state->polarity != PWM_POLARITY_NORMAL)
+		return -EOPNOTSUPP;
 
-static void crc_pwm_disable(struct pwm_chip *c, struct pwm_device *pwm)
-{
-	struct crystalcove_pwm *crc_pwm = to_crc_pwm(c);
-	int div = crc_pwm_calc_clk_div(pwm_get_period(pwm));
+	if (pwm_is_enabled(pwm) && !state->enabled) {
+		err = regmap_write(crc_pwm->regmap, BACKLIGHT_EN, 0);
+		if (err) {
+			dev_err(dev, "Error writing BACKLIGHT_EN %d\n", err);
+			return err;
+		}
+	}
 
-	regmap_write(crc_pwm->regmap, BACKLIGHT_EN, 0);
-	regmap_write(crc_pwm->regmap, PWM0_CLK_DIV, div);
-}
+	if (pwm_get_duty_cycle(pwm) != state->duty_cycle ||
+	    pwm_get_period(pwm) != state->period) {
+		u64 level = state->duty_cycle * PWM_MAX_LEVEL;
 
-static int crc_pwm_config(struct pwm_chip *c, struct pwm_device *pwm,
-			  int duty_ns, int period_ns)
-{
-	struct crystalcove_pwm *crc_pwm = to_crc_pwm(c);
-	struct device *dev = crc_pwm->chip.dev;
-	int level;
+		do_div(level, state->period);
 
-	if (period_ns > PWM_MAX_PERIOD_NS) {
-		dev_err(dev, "un-supported period_ns\n");
-		return -EINVAL;
+		err = regmap_write(crc_pwm->regmap, PWM0_DUTY_CYCLE, level);
+		if (err) {
+			dev_err(dev, "Error writing PWM0_DUTY_CYCLE %d\n", err);
+			return err;
+		}
 	}
 
-	if (pwm_get_period(pwm) != period_ns) {
-		int clk_div = crc_pwm_calc_clk_div(period_ns);
-
+	if (pwm_is_enabled(pwm) && state->enabled &&
+	    pwm_get_period(pwm) != state->period) {
 		/* changing the clk divisor, clear PWM_OUTPUT_ENABLE first */
-		regmap_write(crc_pwm->regmap, PWM0_CLK_DIV, 0);
+		err = regmap_write(crc_pwm->regmap, PWM0_CLK_DIV, 0);
+		if (err) {
+			dev_err(dev, "Error writing PWM0_CLK_DIV %d\n", err);
+			return err;
+		}
+	}
 
-		regmap_write(crc_pwm->regmap, PWM0_CLK_DIV,
-					clk_div | PWM_OUTPUT_ENABLE);
+	if (pwm_get_period(pwm) != state->period ||
+	    pwm_is_enabled(pwm) != state->enabled) {
+		int clk_div = crc_pwm_calc_clk_div(state->period);
+		int pwm_output_enable = state->enabled ? PWM_OUTPUT_ENABLE : 0;
+
+		err = regmap_write(crc_pwm->regmap, PWM0_CLK_DIV,
+				   clk_div | pwm_output_enable);
+		if (err) {
+			dev_err(dev, "Error writing PWM0_CLK_DIV %d\n", err);
+			return err;
+		}
 	}
 
-	/* change the pwm duty cycle */
-	level = duty_ns * PWM_MAX_LEVEL / period_ns;
-	regmap_write(crc_pwm->regmap, PWM0_DUTY_CYCLE, level);
+	if (!pwm_is_enabled(pwm) && state->enabled) {
+		err = regmap_write(crc_pwm->regmap, BACKLIGHT_EN, 1);
+		if (err) {
+			dev_err(dev, "Error writing BACKLIGHT_EN %d\n", err);
+			return err;
+		}
+	}
 
 	return 0;
 }
 
 static const struct pwm_ops crc_pwm_ops = {
-	.config = crc_pwm_config,
-	.enable = crc_pwm_enable,
-	.disable = crc_pwm_disable,
+	.apply = crc_pwm_apply,
 };
 
 static int crystalcove_pwm_probe(struct platform_device *pdev)
Signature · 1 line
2.28.0
#12 lore raw

PATCH v6 12/16 pwm: crc: Implement get_state() method

In reply to Hans de Goede

Implement the pwm_ops.get_state() method to complete the support for the new atomic PWM API.

---
Changes in v6:
- Rebase on 5.9-rc1
- Use DIV_ROUND_UP_ULL because pwm_state.period and .duty_cycle are now u64

Changes in v5:
- Fix an indentation issue

Changes in v4:
- Use DIV_ROUND_UP when calculating the period and duty_cycle from the controller's register values

Changes in v3:
- Add Andy's Reviewed-by tag
- Remove extra whitespace to align some code after assignments (requested by Uwe Kleine-König)

---
 drivers/pwm/pwm-crc.c | 31 +++++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)
drivers/pwm/pwm-crc.c +31 -0
index 27dc30882424..ecfdfac0c2d9 100644
@@ -121,8 +121,39 @@ static int crc_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 	return 0;
 }
 
+static void crc_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
+			      struct pwm_state *state)
+{
+	struct crystalcove_pwm *crc_pwm = to_crc_pwm(chip);
+	struct device *dev = crc_pwm->chip.dev;
+	unsigned int clk_div, clk_div_reg, duty_cycle_reg;
+	int error;
+
+	error = regmap_read(crc_pwm->regmap, PWM0_CLK_DIV, &clk_div_reg);
+	if (error) {
+		dev_err(dev, "Error reading PWM0_CLK_DIV %d\n", error);
+		return;
+	}
+
+	error = regmap_read(crc_pwm->regmap, PWM0_DUTY_CYCLE, &duty_cycle_reg);
+	if (error) {
+		dev_err(dev, "Error reading PWM0_DUTY_CYCLE %d\n", error);
+		return;
+	}
+
+	clk_div = (clk_div_reg & ~PWM_OUTPUT_ENABLE) + 1;
+
+	state->period =
+		DIV_ROUND_UP(clk_div * NSEC_PER_USEC * 256, PWM_BASE_CLK_MHZ);
+	state->duty_cycle =
+		DIV_ROUND_UP_ULL(duty_cycle_reg * state->period, PWM_MAX_LEVEL);
+	state->polarity = PWM_POLARITY_NORMAL;
+	state->enabled = !!(clk_div_reg & PWM_OUTPUT_ENABLE);
+}
+
 static const struct pwm_ops crc_pwm_ops = {
 	.apply = crc_pwm_apply,
+	.get_state = crc_pwm_get_state,
 };
 
 static int crystalcove_pwm_probe(struct platform_device *pdev)
Signature · 6 lines
2.28.0

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#13 lore raw

PATCH v6 13/16 drm/i915: panel: Add get_vbt_pwm_freq() helper

In reply to Hans de Goede

Factor the code which checks and drm_dbg_kms-s the VBT PWM frequency out of get_backlight_max_vbt().

This is a preparation patch for honering the VBT PWM frequency for devices which use an external PWM controller (devices using pwm_setup_backlight()).

---
 drivers/gpu/drm/i915/display/intel_panel.c | 27 ++++++++++++++--------
 1 file changed, 17 insertions(+), 10 deletions(-)
drivers/gpu/drm/i915/display/intel_panel.c +17 -10
index bbde3b12c311..ec6b9d704542 100644
@@ -1543,18 +1543,9 @@ static u32 vlv_hz_to_pwm(struct intel_connector *connector, u32 pwm_freq_hz)
 	return DIV_ROUND_CLOSEST(clock, pwm_freq_hz * mul);
 }
 
-static u32 get_backlight_max_vbt(struct intel_connector *connector)
+static u16 get_vbt_pwm_freq(struct drm_i915_private *dev_priv)
 {
-	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
-	struct intel_panel *panel = &connector->panel;
 	u16 pwm_freq_hz = dev_priv->vbt.backlight.pwm_freq_hz;
-	u32 pwm;
-
-	if (!panel->backlight.hz_to_pwm) {
-		drm_dbg_kms(&dev_priv->drm,
-			    "backlight frequency conversion not supported\n");
-		return 0;
-	}
 
 	if (pwm_freq_hz) {
 		drm_dbg_kms(&dev_priv->drm,
@@ -1567,6 +1558,22 @@ static u32 get_backlight_max_vbt(struct intel_connector *connector)
 			    pwm_freq_hz);
 	}
 
+	return pwm_freq_hz;
+}
+
+static u32 get_backlight_max_vbt(struct intel_connector *connector)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_panel *panel = &connector->panel;
+	u16 pwm_freq_hz = get_vbt_pwm_freq(dev_priv);
+	u32 pwm;
+
+	if (!panel->backlight.hz_to_pwm) {
+		drm_dbg_kms(&dev_priv->drm,
+			    "backlight frequency conversion not supported\n");
+		return 0;
+	}
+
 	pwm = panel->backlight.hz_to_pwm(connector, pwm_freq_hz);
 	if (!pwm) {
 		drm_dbg_kms(&dev_priv->drm,
Signature · 1 line
2.28.0
#14 lore raw

PATCH v6 14/16 drm/i915: panel: Honor the VBT PWM frequency for devs with an external PWM controller

In reply to Hans de Goede

So far for devices using an external PWM controller (devices using pwm_setup_backlight()), we have been hardcoding the period-time passed to pwm_config() to 21333 ns.

I suspect this was done because many VBTs set the PWM frequency to 200 which corresponds to a period-time of 5000000 ns, which greatly exceeds the PWM_MAX_PERIOD_NS define in the Crystal Cove PMIC PWM driver, which used to be 21333.

This PWM_MAX_PERIOD_NS define was actually based on a bug in the PWM driver where its period and duty-cycle times where off by a factor of 256.

Due to this bug the hardcoded CRC_PMIC_PWM_PERIOD_NS value of 21333 would result in the PWM driver using its divider of 128, which would result in a PWM output frequency of 6000000 Hz / 256 / 128 = 183 Hz. So actually pretty close to the default VBT value of 200 Hz.

Now that this bug in the pwm-crc driver is fixed, we can actually use the VBT defined frequency.

This is important because:

a) With the pwm-crc driver fixed it will now translate the hardcoded CRC_PMIC_PWM_PERIOD_NS value of 21333 ns / 46 Khz to a PWM output frequency of 23 KHz (the max it can do).

b) The pwm-lpss driver used on many models has always honored the 21333 ns / 46 Khz request

Some panels do not like such high output frequencies. E.g. on a Terra Pad 1061 tablet, using the LPSS PWM controller, the backlight would go from off to max, when changing the sysfs backlight brightness value from 90-100%, anything under aprox. 90% would turn the backlight fully off.

Honoring the VBT specified PWM frequency will also hopefully fix the various bug reports which we have received about users perceiving the backlight to flicker after a suspend/resume cycle.

---
 .../drm/i915/display/intel_display_types.h    |  1 +
 drivers/gpu/drm/i915/display/intel_panel.c    | 19 +++++++++++--------
 2 files changed, 12 insertions(+), 8 deletions(-)
drivers/gpu/drm/i915/display/intel_display_types.h +1 -0
index e8f809161c75..7171e7c8d928 100644
@@ -223,6 +223,7 @@ struct intel_panel {
 		bool util_pin_active_low;	/* bxt+ */
 		u8 controller;		/* bxt+ only */
 		struct pwm_device *pwm;
+		int pwm_period_ns;
 
 		/* DPCD backlight */
 		u8 pwmgen_bit_count;
drivers/gpu/drm/i915/display/intel_panel.c +11 -8
index ec6b9d704542..7fb162fac8a1 100644
@@ -40,8 +40,6 @@
 #include "intel_dsi_dcs_backlight.h"
 #include "intel_panel.h"
 
-#define CRC_PMIC_PWM_PERIOD_NS	21333
-
 void
 intel_fixed_panel_mode(const struct drm_display_mode *fixed_mode,
 		       struct drm_display_mode *adjusted_mode)
@@ -597,7 +595,7 @@ static u32 pwm_get_backlight(struct intel_connector *connector)
 	int duty_ns;
 
 	duty_ns = pwm_get_duty_cycle(panel->backlight.pwm);
-	return DIV_ROUND_UP(duty_ns * 100, CRC_PMIC_PWM_PERIOD_NS);
+	return DIV_ROUND_UP(duty_ns * 100, panel->backlight.pwm_period_ns);
 }
 
 static void lpt_set_backlight(const struct drm_connector_state *conn_state, u32 level)
@@ -671,9 +669,10 @@ static void bxt_set_backlight(const struct drm_connector_state *conn_state, u32
 static void pwm_set_backlight(const struct drm_connector_state *conn_state, u32 level)
 {
 	struct intel_panel *panel = &to_intel_connector(conn_state->connector)->panel;
-	int duty_ns = DIV_ROUND_UP(level * CRC_PMIC_PWM_PERIOD_NS, 100);
+	int duty_ns = DIV_ROUND_UP(level * panel->backlight.pwm_period_ns, 100);
 
-	pwm_config(panel->backlight.pwm, duty_ns, CRC_PMIC_PWM_PERIOD_NS);
+	pwm_config(panel->backlight.pwm, duty_ns,
+		   panel->backlight.pwm_period_ns);
 }
 
 static void
@@ -1917,6 +1916,9 @@ static int pwm_setup_backlight(struct intel_connector *connector,
 		return -ENODEV;
 	}
 
+	panel->backlight.pwm_period_ns = NSEC_PER_SEC /
+					 get_vbt_pwm_freq(dev_priv);
+
 	/*
 	 * FIXME: pwm_apply_args() should be removed when switching to
 	 * the atomic PWM API.
@@ -1926,9 +1928,10 @@ static int pwm_setup_backlight(struct intel_connector *connector,
 	panel->backlight.min = 0; /* 0% */
 	panel->backlight.max = 100; /* 100% */
 	level = intel_panel_compute_brightness(connector, 100);
-	ns = DIV_ROUND_UP(level * CRC_PMIC_PWM_PERIOD_NS, 100);
+	ns = DIV_ROUND_UP(level * panel->backlight.pwm_period_ns, 100);
 
-	retval = pwm_config(panel->backlight.pwm, ns, CRC_PMIC_PWM_PERIOD_NS);
+	retval = pwm_config(panel->backlight.pwm, ns,
+			    panel->backlight.pwm_period_ns);
 	if (retval < 0) {
 		drm_err(&dev_priv->drm, "Failed to configure the pwm chip\n");
 		pwm_put(panel->backlight.pwm);
@@ -1937,7 +1940,7 @@ static int pwm_setup_backlight(struct intel_connector *connector,
 	}
 
 	level = DIV_ROUND_UP_ULL(pwm_get_duty_cycle(panel->backlight.pwm) * 100,
-			     CRC_PMIC_PWM_PERIOD_NS);
+				 panel->backlight.pwm_period_ns);
 	panel->backlight.level =
 		intel_panel_compute_brightness(connector, level);
 	panel->backlight.enabled = panel->backlight.level != 0;
Signature · 1 line
2.28.0
#15 lore raw

PATCH v6 15/16 drm/i915: panel: Honor the VBT PWM min setting for devs with an external PWM controller

In reply to Hans de Goede

So far for devices using an external PWM controller (devices using pwm_setup_backlight()), we have been hardcoding the minimum allowed PWM level to 0. But several of these devices specify a non 0 minimum setting in their VBT.

Change pwm_setup_backlight() to use get_backlight_min_vbt() to get the minimum level.

---
 drivers/gpu/drm/i915/display/intel_panel.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/gpu/drm/i915/display/intel_panel.c +4 -3
index 7fb162fac8a1..6d27630dd1e4 100644
@@ -1925,8 +1925,8 @@ static int pwm_setup_backlight(struct intel_connector *connector,
 	 */
 	pwm_apply_args(panel->backlight.pwm);
 
-	panel->backlight.min = 0; /* 0% */
 	panel->backlight.max = 100; /* 100% */
+	panel->backlight.min = get_backlight_min_vbt(connector);
 	level = intel_panel_compute_brightness(connector, 100);
 	ns = DIV_ROUND_UP(level * panel->backlight.pwm_period_ns, 100);
 
@@ -1941,8 +1941,9 @@ static int pwm_setup_backlight(struct intel_connector *connector,
 
 	level = DIV_ROUND_UP_ULL(pwm_get_duty_cycle(panel->backlight.pwm) * 100,
 				 panel->backlight.pwm_period_ns);
-	panel->backlight.level =
-		intel_panel_compute_brightness(connector, level);
+	level = intel_panel_compute_brightness(connector, level);
+	panel->backlight.level = clamp(level, panel->backlight.min,
+				       panel->backlight.max);
 	panel->backlight.enabled = panel->backlight.level != 0;
 
 	drm_info(&dev_priv->drm, "Using %s PWM for LCD backlight control\n",
Signature · 6 lines
2.28.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#16 lore raw

PATCH v6 16/16 drm/i915: panel: Use atomic PWM API for devs with an external PWM controller

In reply to Hans de Goede

Now that the PWM drivers which we use have been converted to the atomic PWM API, we can move the i915 panel code over to using the atomic PWM API.

The removes a long standing FIXME and this removes a flicker where the backlight brightness would jump to 100% when i915 loads even if using the fastset path.

Note that this commit also simplifies pwm_disable_backlight(), by dropping the intel_panel_actually_set_backlight(..., 0) call. This call sets the PWM to 0% duty-cycle. I believe that this call was only present as a workaround for a bug in the pwm-crc.c driver where it failed to clear the PWM_OUTPUT_ENABLE bit. This is fixed by an earlier patch in this series.

After the dropping of this workaround, the usleep call, which seems unnecessary to begin with, has no useful effect anymore, so drop that too.

---
Changes in v6:
- Drop the pwm_get_period() check in pwm_setup(), it is now longer needed now that we use pwm_get_relative_duty_cycle()

Changes in v4:
- Add a note to the commit message about the dropping of the intel_panel_actually_set_backlight() and usleep() calls from pwm_disable_backlight()
- Use the pwm_set/get_relative_duty_cycle() helpers instead of using DIY code for this

---
 .../drm/i915/display/intel_display_types.h    |  3 +-
 drivers/gpu/drm/i915/display/intel_panel.c    | 70 ++++++++-----------
 2 files changed, 33 insertions(+), 40 deletions(-)
drivers/gpu/drm/i915/display/intel_display_types.h +2 -1
index 7171e7c8d928..e3ebe7c313ba 100644
@@ -28,6 +28,7 @@
 
 #include <linux/async.h>
 #include <linux/i2c.h>
+#include <linux/pwm.h>
 #include <linux/sched/clock.h>
 
 #include <drm/drm_atomic.h>
@@ -223,7 +224,7 @@ struct intel_panel {
 		bool util_pin_active_low;	/* bxt+ */
 		u8 controller;		/* bxt+ only */
 		struct pwm_device *pwm;
-		int pwm_period_ns;
+		struct pwm_state pwm_state;
 
 		/* DPCD backlight */
 		u8 pwmgen_bit_count;
drivers/gpu/drm/i915/display/intel_panel.c +31 -39

113 lines not on this page · raw message

Signature · 1 line
2.28.0
#17 lore raw

Re: [PATCH v6 16/16] drm/i915: panel: Use atomic PWM API for devs with an external PWM controller

I love your patch! Yet something to improve:

Hi Hans,

I love your patch! Yet something to improve:

[auto build test ERROR on pwm/for-next]
[also build test ERROR on pm/linux-next v5.9-rc2 next-20200824] [cannot apply to drm-intel/for-linux-next]
[If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/0day-ci/linux/commits/Hans-de-Goede/acpi-pwm-i915-Convert-pwm-crc-and-i915-driver-s-PWM-code-to-use-the-atomic-PWM-API/20200824-200516
base:   https://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm.git for-next
config: i386-randconfig-r021-20200824 (attached as .config)
compiler: gcc-9 (Debian 9.3.0-15) 9.3.0
reproduce (this is a W=1 build):
        # save the attached .config to linux build tree
        make W=1 ARCH=i386 

If you fix the issue, kindly add following tag as appropriate

All errors (new ones prefixed by >>):

ld: drivers/gpu/drm/i915/display/intel_panel.o: in function `pwm_setup_backlight':

>> drivers/gpu/drm/i915/display/intel_panel.c:1932: undefined reference to `__udivdi3'

# https://github.com/0day-ci/linux/commit/72f1809d336477ff767fc9d5b65ac79dd31b6dca
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Hans-de-Goede/acpi-pwm-i915-Convert-pwm-crc-and-i915-driver-s-PWM-code-to-use-the-atomic-PWM-API/20200824-200516 git checkout 72f1809d336477ff767fc9d5b65ac79dd31b6dca
vim +1932 drivers/gpu/drm/i915/display/intel_panel.c

1892
1893 static int pwm_setup_backlight(struct intel_connector *connector,
1894 enum pipe pipe)
1895 {
1896 struct drm_device *dev = connector->base.dev;
1897 struct drm_i915_private *dev_priv = to_i915(dev);
1898 struct intel_panel *panel = &connector->panel;
1899 const char *desc;
1900 u32 level;
1901
1902 /* Get the right PWM chip for DSI backlight according to VBT */
1903 if (dev_priv->vbt.dsi.config->pwm_blc == PPS_BLC_PMIC) {
1904 panel->backlight.pwm = pwm_get(dev->dev, "pwm_pmic_backlight");
1905 desc = "PMIC";
1906 } else {
1907 panel->backlight.pwm = pwm_get(dev->dev, "pwm_soc_backlight");
1908 desc = "SoC";
1909 }
1910
1911 if (IS_ERR(panel->backlight.pwm)) {
1912 drm_err(&dev_priv->drm, "Failed to get the %s PWM chip\n",
1913 desc);
1914 panel->backlight.pwm = NULL;
1915 return -ENODEV;
1916 }
1917
1918 panel->backlight.max = 100; /* 100% */
1919 panel->backlight.min = get_backlight_min_vbt(connector);
1920
1921 if (pwm_is_enabled(panel->backlight.pwm)) {
1922 /* PWM is already enabled, use existing settings */
1923 pwm_get_state(panel->backlight.pwm, &panel->backlight.pwm_state);
1924
1925 level = pwm_get_relative_duty_cycle(&panel->backlight.pwm_state,
1926 100);
1927 level = intel_panel_compute_brightness(connector, level);
1928 panel->backlight.level = clamp(level, panel->backlight.min,
1929 panel->backlight.max);
1930 panel->backlight.enabled = true;
1931

> 1932			drm_dbg_kms(&dev_priv->drm, "PWM already enabled at freq %lld, VBT freq %d, level %d\n",

1933 NSEC_PER_SEC / panel->backlight.pwm_state.period,
1934 get_vbt_pwm_freq(dev_priv), level);
1935 } else {
1936 /* Set period from VBT frequency, leave other settings at 0. */
1937 panel->backlight.pwm_state.period =
1938 NSEC_PER_SEC / get_vbt_pwm_freq(dev_priv);
1939 }
1940
1941 drm_info(&dev_priv->drm, "Using %s PWM for LCD backlight control\n",
1942 desc);
1943 return 0;
1944 }
1945

---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all(a)lists.01.org

#18 lore raw

[Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for acpi/pwm/i915: Convert pwm-crc and i915 driver's PWM code to use the atomic PWM API

In reply to Hans de Goede
== Series Details ==

== Series Details ==

Series: acpi/pwm/i915: Convert pwm-crc and i915 driver's PWM code to use the atomic PWM API
URL : https://patchwork.freedesktop.org/series/80943/
State : warning

== Summary ==

$ dim checkpatch origin/drm-tip
23eeb608a11a ACPI / LPSS: Resume Cherry Trail PWM controller in no-irq phase
3404311e82b8 ACPI / LPSS: Save Cherry Trail PWM ctx registers only once (at activation)
cc49add91e96 pwm: lpss: Fix off by one error in base_unit math in pwm_lpss_prepare()
a9f8c291fa0f pwm: lpss: Add range limit check for the base_unit register value
a7c9b3968280 pwm: lpss: Add pwm_lpss_prepare_enable() helper
-:45: CHECK:BOOL_COMPARISON: Using comparison to false is error prone
#45: FILE: drivers/pwm/pwm-lpss.c:137:
+	pwm_lpss_cond_enable(pwm, enable && lpwm->info->bypass == false);

-:50: CHECK:BOOL_COMPARISON: Using comparison to true is error prone #50: FILE: drivers/pwm/pwm-lpss.c:142:
+ pwm_lpss_cond_enable(pwm, enable && lpwm->info->bypass == true);

total: 0 errors, 0 warnings, 2 checks, 67 lines checked
19fbcc493a46 pwm: lpss: Use pwm_lpss_apply() when restoring state on resume 23df6f9340c1 pwm: crc: Fix period / duty_cycle times being off by a factor of 256 a9c78de3ade3 pwm: crc: Fix off-by-one error in the clock-divider calculations 9d3242bf8a3e pwm: crc: Fix period changes not having any effect
8b8e82933140 pwm: crc: Enable/disable PWM output on enable/disable
6a44ff1498a2 pwm: crc: Implement apply() method to support the new atomic PWM API c72a3592f7d9 pwm: crc: Implement get_state() method
1f8f97bf9b4a drm/i915: panel: Add get_vbt_pwm_freq() helper
c1026447b3e9 drm/i915: panel: Honor the VBT PWM frequency for devs with an external PWM controller 5e7767931e02 drm/i915: panel: Honor the VBT PWM min setting for devs with an external PWM controller 80c31f95dffd drm/i915: panel: Use atomic PWM API for devs with an external PWM controller

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#19 lore raw

[Intel-gfx] ✓ Fi.CI.BAT: success for acpi/pwm/i915: Convert pwm-crc and i915 driver's PWM code to use the atomic PWM API

In reply to Hans de Goede
== Series Details ==

== Series Details ==

Series: acpi/pwm/i915: Convert pwm-crc and i915 driver's PWM code to use the atomic PWM API
URL : https://patchwork.freedesktop.org/series/80943/
State : success

== Summary ==

CI Bug Log - changes from CI_DRM_8918 -> Patchwork_18393
====================================================

Summary
-------

**SUCCESS**

No regressions found.

External URL: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/index.html

Known issues
------------

Here are the changes found in Patchwork_18393 that come from known issues:

### IGT changes ###

#### Issues hit ####

* igt@i915_module_load@reload:
- fi-byt-j1900: [PASS][1] -> [DMESG-WARN][2] ([i915#1982]) +1 similar issue
[1]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/fi-byt-j1900/igt@[email protected]
[2]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/fi-byt-j1900/igt@[email protected]
- fi-apl-guc: [PASS][3] -> [DMESG-WARN][4] ([i915#1635] / [i915#1982])
[3]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/fi-apl-guc/igt@[email protected]
[4]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/fi-apl-guc/igt@[email protected]

* igt@kms_cursor_legacy@basic-busy-flip-before-cursor-atomic:
- fi-bsw-kefka: [PASS][5] -> [DMESG-WARN][6] ([i915#1982])
[5]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/fi-bsw-kefka/igt@[email protected]
[6]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/fi-bsw-kefka/igt@[email protected]

#### Possible fixes ####

* igt@kms_cursor_legacy@basic-busy-flip-before-cursor-atomic:
- fi-bsw-n3050: [DMESG-WARN][7] ([i915#1982]) -> [PASS][8] +1 similar issue
[7]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/fi-bsw-n3050/igt@[email protected]
[8]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/fi-bsw-n3050/igt@[email protected]

* igt@kms_flip@basic-flip-vs-wf_vblank@c-hdmi-a2:
- fi-skl-guc: [DMESG-WARN][9] ([i915#2203]) -> [PASS][10]
[9]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/fi-skl-guc/igt@kms_flip@[email protected]
[10]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/fi-skl-guc/igt@kms_flip@[email protected]

#### Warnings ####

* igt@gem_exec_suspend@basic-s0:
- fi-kbl-x1275: [DMESG-WARN][11] ([i915#62] / [i915#92]) -> [DMESG-WARN][12] ([i915#62] / [i915#92] / [i915#95]) +3 similar issues
[11]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/fi-kbl-x1275/igt@[email protected]
[12]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/fi-kbl-x1275/igt@[email protected]

* igt@kms_cursor_legacy@basic-flip-after-cursor-varying-size:
- fi-kbl-x1275: [DMESG-WARN][13] ([i915#62] / [i915#92] / [i915#95]) -> [DMESG-WARN][14] ([i915#62] / [i915#92]) +2 similar issues
[13]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/fi-kbl-x1275/igt@[email protected]
[14]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/fi-kbl-x1275/igt@[email protected]

[i915#1635]: https://gitlab.freedesktop.org/drm/intel/issues/1635
[i915#1982]: https://gitlab.freedesktop.org/drm/intel/issues/1982
[i915#2203]: https://gitlab.freedesktop.org/drm/intel/issues/2203
[i915#62]: https://gitlab.freedesktop.org/drm/intel/issues/62
[i915#92]: https://gitlab.freedesktop.org/drm/intel/issues/92
[i915#95]: https://gitlab.freedesktop.org/drm/intel/issues/95

Participating hosts (37 -> 34)
------------------------------

Missing (3): fi-byt-clapper fi-byt-squawks fi-bsw-cyan

Build changes
-------------

* Linux: CI_DRM_8918 -> Patchwork_18393

CI-20190529: 20190529
CI_DRM_8918: 7296072da95d2d2550ef2d4836bc72663ee711cc @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_5770: f1d0c240ea2e631dfb9f493f37f8fb61cb2b1cf2 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_18393: 80c31f95dffd9ca6f68ebccad21ec4a92958ba46 @ git://anongit.freedesktop.org/gfx-ci/linux

== Linux commits ==

80c31f95dffd drm/i915: panel: Use atomic PWM API for devs with an external PWM controller 5e7767931e02 drm/i915: panel: Honor the VBT PWM min setting for devs with an external PWM controller c1026447b3e9 drm/i915: panel: Honor the VBT PWM frequency for devs with an external PWM controller 1f8f97bf9b4a drm/i915: panel: Add get_vbt_pwm_freq() helper
c72a3592f7d9 pwm: crc: Implement get_state() method
6a44ff1498a2 pwm: crc: Implement apply() method to support the new atomic PWM API 8b8e82933140 pwm: crc: Enable/disable PWM output on enable/disable
9d3242bf8a3e pwm: crc: Fix period changes not having any effect
a9c78de3ade3 pwm: crc: Fix off-by-one error in the clock-divider calculations 23df6f9340c1 pwm: crc: Fix period / duty_cycle times being off by a factor of 256 19fbcc493a46 pwm: lpss: Use pwm_lpss_apply() when restoring state on resume a7c9b3968280 pwm: lpss: Add pwm_lpss_prepare_enable() helper
a9f8c291fa0f pwm: lpss: Add range limit check for the base_unit register value cc49add91e96 pwm: lpss: Fix off by one error in base_unit math in pwm_lpss_prepare() 3404311e82b8 ACPI / LPSS: Save Cherry Trail PWM ctx registers only once (at activation) 23eeb608a11a ACPI / LPSS: Resume Cherry Trail PWM controller in no-irq phase

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/index.html

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#20 lore raw

[Intel-gfx] ✓ Fi.CI.IGT: success for acpi/pwm/i915: Convert pwm-crc and i915 driver's PWM code to use the atomic PWM API

In reply to Hans de Goede
== Series Details ==

== Series Details ==

Series: acpi/pwm/i915: Convert pwm-crc and i915 driver's PWM code to use the atomic PWM API
URL : https://patchwork.freedesktop.org/series/80943/
State : success

== Summary ==

CI Bug Log - changes from CI_DRM_8918_full -> Patchwork_18393_full
====================================================

Summary
-------

**SUCCESS**

No regressions found.

Known issues
------------

Here are the changes found in Patchwork_18393_full that come from known issues:

### IGT changes ###

#### Issues hit ####

* igt@gem_ctx_isolation@preservation-s3@rcs0:
- shard-kbl: [PASS][1] -> [DMESG-WARN][2] ([i915#180]) +4 similar issues
[1]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-kbl7/igt@gem_ctx_isolation@[email protected]
[2]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-kbl7/igt@gem_ctx_isolation@[email protected]

* igt@gem_exec_balancer@bonded-early:
- shard-kbl: [PASS][3] -> [FAIL][4] ([i915#2079])
[3]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-kbl2/igt@[email protected]
[4]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-kbl2/igt@[email protected]

* igt@gem_exec_whisper@basic-forked-all:
- shard-glk: [PASS][5] -> [DMESG-WARN][6] ([i915#118] / [i915#95])
[5]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-glk6/igt@[email protected]
[6]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-glk6/igt@[email protected]

* igt@gem_partial_pwrite_pread@reads-uncached:
- shard-apl: [PASS][7] -> [FAIL][8] ([i915#1635])
[7]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-apl3/igt@[email protected]
[8]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-apl2/igt@[email protected]

* igt@kms_big_fb@linear-64bpp-rotate-0:
- shard-glk: [PASS][9] -> [DMESG-FAIL][10] ([i915#118] / [i915#95])
[9]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-glk1/igt@[email protected]
[10]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-glk8/igt@[email protected]

* igt@kms_big_fb@x-tiled-32bpp-rotate-180:
- shard-skl: [PASS][11] -> [DMESG-WARN][12] ([i915#1982]) +16 similar issues
[11]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-skl6/igt@[email protected]
[12]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-skl5/igt@[email protected]

* igt@kms_draw_crc@draw-method-rgb565-mmap-gtt-untiled:
- shard-apl: [PASS][13] -> [DMESG-WARN][14] ([i915#1635] / [i915#1982])
[13]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-apl3/igt@[email protected]
[14]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-apl4/igt@[email protected]

* igt@kms_flip@flip-vs-suspend@c-edp1:
- shard-skl: [PASS][15] -> [INCOMPLETE][16] ([i915#198])
[15]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-skl10/igt@kms_flip@[email protected]
[16]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-skl4/igt@kms_flip@[email protected]

* igt@kms_frontbuffer_tracking@fbc-stridechange:
- shard-tglb: [PASS][17] -> [DMESG-WARN][18] ([i915#1982]) +1 similar issue
[17]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-tglb2/igt@[email protected]
[18]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-tglb1/igt@[email protected]

* igt@kms_hdr@bpc-switch-dpms:
- shard-skl: [PASS][19] -> [FAIL][20] ([i915#1188])
[19]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-skl9/igt@[email protected]
[20]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-skl8/igt@[email protected]

* igt@kms_pipe_crc_basic@suspend-read-crc-pipe-c:
- shard-glk: [PASS][21] -> [DMESG-WARN][22] ([i915#1982]) +1 similar issue
[21]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-glk6/igt@[email protected]
[22]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-glk8/igt@[email protected]

* igt@kms_psr@psr2_sprite_blt:
- shard-iclb: [PASS][23] -> [SKIP][24] ([fdo#109441]) +1 similar issue
[23]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-iclb2/igt@kms_psr@psr2_sprite_blt.html
[24]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-iclb7/igt@kms_psr@psr2_sprite_blt.html

* igt@perf@polling-parameterized:
- shard-tglb: [PASS][25] -> [FAIL][26] ([i915#1542])
[25]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-tglb2/igt@[email protected]
[26]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-tglb1/igt@[email protected]

* igt@prime_busy@hang@bcs0:
- shard-hsw: [PASS][27] -> [FAIL][28] ([i915#2258]) +4 similar issues
[27]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-hsw8/igt@prime_busy@[email protected]
[28]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-hsw1/igt@prime_busy@[email protected]

#### Possible fixes ####

* igt@gem_caching@read-writes:
- shard-skl: [DMESG-WARN][29] ([i915#1982]) -> [PASS][30] +10 similar issues
[29]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-skl2/igt@[email protected]
[30]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-skl9/igt@[email protected]

* igt@gem_exec_create@forked:
- shard-glk: [DMESG-WARN][31] ([i915#118] / [i915#95]) -> [PASS][32]
[31]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-glk6/igt@[email protected]
[32]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-glk8/igt@[email protected]

* igt@i915_pm_rpm@system-suspend:
- shard-kbl: [INCOMPLETE][33] ([i915#151] / [i915#155]) -> [PASS][34]
[33]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-kbl2/igt@[email protected]
[34]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-kbl1/igt@[email protected]

* igt@kms_big_fb@x-tiled-8bpp-rotate-0:
- shard-kbl: [DMESG-WARN][35] ([i915#1982]) -> [PASS][36]
[35]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-kbl4/igt@[email protected]
[36]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-kbl7/igt@[email protected]

* igt@kms_flip@flip-vs-suspend-interruptible@a-dp1:
- shard-kbl: [DMESG-WARN][37] ([i915#180]) -> [PASS][38] +7 similar issues
[37]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-kbl4/igt@kms_flip@[email protected]
[38]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-kbl7/igt@kms_flip@[email protected]

* igt@kms_frontbuffer_tracking@fbc-1p-primscrn-cur-indfb-draw-blt:
- shard-tglb: [DMESG-WARN][39] ([i915#1982]) -> [PASS][40]
[39]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-tglb1/igt@[email protected]
[40]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-tglb7/igt@[email protected]

* igt@kms_frontbuffer_tracking@fbc-1p-primscrn-pri-shrfb-draw-pwrite:
- shard-apl: [DMESG-WARN][41] ([i915#1635] / [i915#1982]) -> [PASS][42] +1 similar issue
[41]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-apl8/igt@kms_frontbuffer_tracking@fbc-1p-primscrn-pri-shrfb-draw-pwrite.html
[42]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-apl8/igt@kms_frontbuffer_tracking@fbc-1p-primscrn-pri-shrfb-draw-pwrite.html

* igt@kms_hdr@bpc-switch:
- shard-skl: [FAIL][43] ([i915#1188]) -> [PASS][44]
[43]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-skl9/igt@[email protected]
[44]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-skl2/igt@[email protected]

* igt@kms_plane_alpha_blend@pipe-c-constant-alpha-min:
- shard-skl: [FAIL][45] ([fdo#108145] / [i915#265]) -> [PASS][46] +1 similar issue
[45]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-skl7/igt@[email protected]
[46]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-skl3/igt@[email protected]

* igt@kms_psr@psr2_primary_mmap_cpu:
- shard-iclb: [SKIP][47] ([fdo#109441]) -> [PASS][48] +1 similar issue
[47]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-iclb5/igt@kms_psr@psr2_primary_mmap_cpu.html
[48]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-iclb2/igt@kms_psr@psr2_primary_mmap_cpu.html

#### Warnings ####

* igt@kms_content_protection@atomic:
- shard-kbl: [TIMEOUT][49] ([i915#1319] / [i915#1958]) -> [TIMEOUT][50] ([i915#1319])
[49]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-kbl1/igt@[email protected]
[50]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-kbl1/igt@[email protected]

* igt@kms_flip_tiling@flip-x-tiled:
- shard-skl: [DMESG-FAIL][51] ([fdo#108145] / [i915#1982]) -> [DMESG-WARN][52] ([i915#1982])
[51]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-skl6/igt@[email protected]
[52]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-skl8/igt@[email protected]

* igt@kms_frontbuffer_tracking@psr-rgb101010-draw-mmap-cpu:
- shard-glk: [INCOMPLETE][53] ([i915#2377]) -> [SKIP][54] ([fdo#109271])
[53]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8918/shard-glk2/igt@[email protected]
[54]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/shard-glk3/igt@[email protected]

[fdo#108145]: https://bugs.freedesktop.org/show_bug.cgi?id=108145
[fdo#109271]: https://bugs.freedesktop.org/show_bug.cgi?id=109271
[fdo#109441]: https://bugs.freedesktop.org/show_bug.cgi?id=109441
[i915#118]: https://gitlab.freedesktop.org/drm/intel/issues/118
[i915#1188]: https://gitlab.freedesktop.org/drm/intel/issues/1188
[i915#1319]: https://gitlab.freedesktop.org/drm/intel/issues/1319
[i915#151]: https://gitlab.freedesktop.org/drm/intel/issues/151
[i915#1542]: https://gitlab.freedesktop.org/drm/intel/issues/1542
[i915#155]: https://gitlab.freedesktop.org/drm/intel/issues/155
[i915#1635]: https://gitlab.freedesktop.org/drm/intel/issues/1635
[i915#180]: https://gitlab.freedesktop.org/drm/intel/issues/180
[i915#1958]: https://gitlab.freedesktop.org/drm/intel/issues/1958
[i915#198]: https://gitlab.freedesktop.org/drm/intel/issues/198
[i915#1982]: https://gitlab.freedesktop.org/drm/intel/issues/1982
[i915#2079]: https://gitlab.freedesktop.org/drm/intel/issues/2079
[i915#2258]: https://gitlab.freedesktop.org/drm/intel/issues/2258
[i915#2377]: https://gitlab.freedesktop.org/drm/intel/issues/2377
[i915#265]: https://gitlab.freedesktop.org/drm/intel/issues/265
[i915#95]: https://gitlab.freedesktop.org/drm/intel/issues/95

Participating hosts (11 -> 11)
------------------------------

No changes in participating hosts

Build changes
-------------

* Linux: CI_DRM_8918 -> Patchwork_18393

CI-20190529: 20190529
CI_DRM_8918: 7296072da95d2d2550ef2d4836bc72663ee711cc @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_5770: f1d0c240ea2e631dfb9f493f37f8fb61cb2b1cf2 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_18393: 80c31f95dffd9ca6f68ebccad21ec4a92958ba46 @ git://anongit.freedesktop.org/gfx-ci/linux
piglit_4509: fdc5a4ca11124ab8413c7988896eec4c97336694 @ git://anongit.freedesktop.org/piglit

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_18393/index.html

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx