gpio: sprd: Clear interrupt when setting the type as edge
Subsystems (2)
Chunyan Zhang
reviewerPATCH v2 1/1 gpio: sprd: Clear interrupt when setting the type as edge
From: Taiping Lai <[email protected]>
The raw interrupt status of GPIO maybe set before the interrupt is enabled, which would trigger the interrupt event once enabled it from user side. This is the case for edge interrupts only. Adding a clear operation when setting interrupt type can avoid that.
There're a few considerations for the solution:
1) This issue is for edge interrupt only; The interrupts requested by users are IRQ_TYPE_LEVEL_HIGH as default, so clearing interrupt when request is useless.
2) The interrupt type can be set to edge when request and following up with clearing it though, but the problem is still there once users set the interrupt type to level trggier.
3) We can add a clear operation after each time of setting interrupt enable bit, but it is redundant for level trigger interrupt.
Therefore, the solution is this patch seems the best for now.
---
* Changes since v1:
- Rebased on v5.9-rc1.
--- drivers/gpio/gpio-sprd.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/gpio/gpio-sprd.c +3 -0
@@ -149,17 +149,20 @@ static int sprd_gpio_irq_set_type(struct irq_data *data,sprd_gpio_update (chip, offset,SPRD_GPIO_IS ,0 );sprd_gpio_update (chip, offset,SPRD_GPIO_IBE ,0 );sprd_gpio_update (chip, offset,SPRD_GPIO_IEV ,1 ); +sprd_gpio_update (chip, offset,SPRD_GPIO_IC ,1 );irq_set_handler_locked (data, handle_edge_irq);break ;case IRQ_TYPE_EDGE_FALLING :sprd_gpio_update (chip, offset,SPRD_GPIO_IS ,0 );sprd_gpio_update (chip, offset,SPRD_GPIO_IBE ,0 );sprd_gpio_update (chip, offset,SPRD_GPIO_IEV ,0 ); +sprd_gpio_update (chip, offset,SPRD_GPIO_IC ,1 );irq_set_handler_locked (data, handle_edge_irq);break ;case IRQ_TYPE_EDGE_BOTH :sprd_gpio_update (chip, offset,SPRD_GPIO_IS ,0 );sprd_gpio_update (chip, offset,SPRD_GPIO_IBE ,1 ); +sprd_gpio_update (chip, offset,SPRD_GPIO_IC ,1 );irq_set_handler_locked (data, handle_edge_irq);break ;case IRQ_TYPE_LEVEL_HIGH :
Signature · 1 line
2.20.1
Bartosz Golaszewski
AppliedQuoted 56 lines · Chunyan Zhang
From: Taiping Lai <[email protected]>
The raw interrupt status of GPIO maybe set before the interrupt is enabled, which would trigger the interrupt event once enabled it from user side. This is the case for edge interrupts only. Adding a clear operation when setting interrupt type can avoid that.
There're a few considerations for the solution:
1) This issue is for edge interrupt only; The interrupts requested by users areIRQ_TYPE_LEVEL_HIGHas default, so clearing interrupt when request is useless.
2) The interrupt type can be set to edge when request and following up with clearing it though, but the problem is still there once users set the interrupt type to level trggier.
3) We can add a clear operation after each time of setting interrupt enable bit, but it is redundant for level trigger interrupt.Therefore, the solution is this patch seems the best for now.
Fixes 9a3821c2bb47 ("gpio: Add GPIO driver for Spreadtrum SC9860 platform")Signed-off-by Taiping Lai <[email protected]>Signed-off-by Chunyan Zhang <[email protected]>---
* Changes since v1:
- Rebased on v5.9-rc1.--- drivers/gpio/gpio-sprd.c | 3 +++ 1 file changed, 3 insertions(+)drivers/gpio/gpio-sprd.c +3
-1@@ -149,17 +149,20 @@ static int sprd_gpio_irq_set_type(struct irq_data *data,sprd_gpio_update (chip, offset,SPRD_GPIO_IS ,0 );sprd_gpio_update (chip, offset,SPRD_GPIO_IBE ,0 );sprd_gpio_update (chip, offset,SPRD_GPIO_IEV ,1 ); +sprd_gpio_update (chip, offset,SPRD_GPIO_IC ,1 );irq_set_handler_locked (data, handle_edge_irq);break ;case IRQ_TYPE_EDGE_FALLING :sprd_gpio_update (chip, offset,SPRD_GPIO_IS ,0 );sprd_gpio_update (chip, offset,SPRD_GPIO_IBE ,0 );sprd_gpio_update (chip, offset,SPRD_GPIO_IEV ,0 ); +sprd_gpio_update (chip, offset,SPRD_GPIO_IC ,1 );irq_set_handler_locked (data, handle_edge_irq);break ;case IRQ_TYPE_EDGE_BOTH :sprd_gpio_update (chip, offset,SPRD_GPIO_IS ,0 );sprd_gpio_update (chip, offset,SPRD_GPIO_IBE ,1 ); +sprd_gpio_update (chip, offset,SPRD_GPIO_IC ,1 );irq_set_handler_locked (data, handle_edge_irq);break ;case IRQ_TYPE_LEVEL_HIGH : --
Quoted 2 lines
2.20.1
Queued for fixes, thanks!
Bartosz