Fix --remote protocol can't be set without port argument
PATCH 1/1 Fix --remote protocol can't be set without port argument
According client-options.rst additional argumets ``port`` and ``proto`` are both optional and it's allowed to have port absent and protocol set:
--remote args
Examples:
remote server.example.net tcp
But when protocol is set without preceeding port argument, it is being misparsed as a port with subsequent error:
RESOLVE: Cannot resolve host address: server.example.net:tcp (Servname not supported for ai_socktype)
Since protocol names are predefined and don't match service names, fix this behavior by checking second argument for valid protocol first.
--- src/openvpn/options.c | 24 +++++++++++++++++------- 1 file changed, 17 insertions(+), 7 deletions(-)
src/openvpn/options.c +17 -7
@@ -5682,16 +5682,26 @@ add_option(struct options *options, re.remote = p[1 ];if (p[2 ]) { - re.remote_port = p[2 ]; -if (p[3 ]) +/* Since port is optional, second parameter can be a protocol */ +int proto =ascii2proto (p[2 ]); +sa_family_t af =ascii2af (p[2 ]); +if (proto <0 ) { -const int proto =ascii2proto (p[3 ]); -const sa_family_t af =ascii2af (p[3 ]); -if (proto <0 ) +/* Second is not proto, port then. Protocol should be third */ + re.remote_port = p[2 ]; +if (p[3 ]) { -msg (msglevel,"remote: bad protocol associated with host %s: '%s'" , p[1 ], p[3 ]); - goto err; + proto =ascii2proto (p[3 ]); + af =ascii2af (p[3 ]); +if (proto <0 ) + { +msg (msglevel,"remote: bad protocol associated with host %s: '%s'" , p[1 ], p[3 ]); + goto err; + } } + } +if (proto >=0 ) + { re.proto = proto; re.af = af; }
Signature · 1 line
2.17.1
Quoted 11 lines · Vladislav Grishenko
According
client-options.rstadditional argumets ``port`` and ``proto`` are both optional and it's allowed to have port absent and protocol set:
--remote args
Examples:
remote server.example.net tcpBut when protocol is set without preceeding port argument, it is being misparsed as a port with subsequent error:
RESOLVE: Cannot resolve host address: server.example.net:tcp (Servname not supported forai_socktype)
Quoted 4 lines
Since protocol names are predefined and don't match service names, fix this behavior by checking second argument for valid protocol first.
Signed-off-by Vladislav Grishenko <[email protected]...>
Uhm ... I'm leaning towards a NAK to this patch and would rather suggest updating the man page to be correct. This is a mistake from my side when converting the man page to .rst files. The example should be:
remote server.example.net 1194 tcp
The OpenVPN 2.4 and prior releases has this line:
--remote host [port] [proto]
But this syntax was not supported by rst2man, so it was replaced with "args" and the examples coming below; which carried an error.
Signature · 4 lines
kind regards, David Sommerseth OpenVPN Inc
Hi David,
Quoted 21 lines
-----Original Message-----
From: David Sommerseth <[email protected]...>
Sent: Tuesday, September 8, 2020 6:23 PM
To: Vladislav Grishenko <[email protected]...>; openvpn- [email protected]
Subject: Re: [Openvpn-devel] [PATCH] Fix --remote protocol can't be set without port argumentQuoted 2 lines · Vladislav Grishenko
According
client-options.rstadditional argumets ``port`` and ``proto`` are both optional and it's allowed to have port absent and protocolset:
Quoted 9 lines
--remote args
Examples:
remote server.example.net tcpBut when protocol is set without preceeding port argument, it is being misparsed as a port with subsequent error:
RESOLVE: Cannot resolve host address: server.example.net:tcp (Servname not supported forai_socktype)
Quoted 9 lines
Quoted 3 lines
Since protocol names are predefined and don't match service names, fix this behavior by checking second argument for valid protocol first.
Uhm ... I'm leaning towards a NAK to this patch and would rather suggest updating the man page to be correct. This is a mistake from my side when converting the man page to .rst files. The example should be:
remote server.example.net 1194 tcp
Hum. Initially all variants were supported, by checking numeric port and taking it as proto, if not numeric. Later port became string servname and optional logic was lost. Man pages still has all of them since that time:
remote server.exmaple.net
remote server.exmaple.net 1194
remote server.exmaple.net tcp
At first look there is no need for proto w/o port set, why it can be important?
With support of server host & port discovery (DNS SRV RFC 2782), port info is not required, only host and protocol make sense. So I though about this one little step forward toward ~consistent syntax. Does it makes any sense?
Quoted 14 lines
The OpenVPN 2.4 and prior releases has this line:
--remote host [port] [proto]
But this syntax was not supported by rst2man, so it was replaced with "args" and the examples coming below; which carried an error.
--
kind regards,David Sommerseth
OpenVPN Inc
Quoted 30 lines · Vladislav Grishenko
Hi David,
Quoted 28 lines
-----Original Message-----
From: David Sommerseth <[email protected]...>
Sent: Tuesday, September 8, 2020 6:23 PM
To: Vladislav Grishenko <[email protected]...>; openvpn- [email protected]
Subject: Re: [Openvpn-devel] [PATCH] Fix --remote protocol can't be set without port argumentQuoted 2 lines · Vladislav Grishenko
According
client-options.rstadditional argumets ``port`` and ``proto`` are both optional and it's allowed to have port absent and protocolset:
Quoted 4 lines
--remote args
Examples:
remote server.example.net tcpQuoted 8 lines
But when protocol is set without preceeding port argument, it is being misparsed as a port with subsequent error:
RESOLVE: Cannot resolve host address: server.example.net:tcp (Servname not supported forai_socktype)Since protocol names are predefined and don't match service names, fix this behavior by checking second argument for valid protocol first.
Uhm ... I'm leaning towards a NAK to this patch and would rather suggest updating the man page to be correct. This is a mistake from my side when converting the man page to .rst files. The example should be:
Quoted 6 lines
Quoted 2 lines
remote server.example.net 1194 tcp
Hum. Initially all variants were supported, by checking numeric port and taking it as proto, if not numeric. Later port became string servname and optional logic was lost.
The man page history disagrees ... even though, it doesn't say this order is explicit.
2.4 - <https://community.openvpn.net/openvpn/wiki/Openvpn24ManPage#lbAG>
2.3 - <https://community.openvpn.net/openvpn/wiki/Openvpn23ManPage#lbAG>
2.2 - <https://community.openvpn.net/openvpn/wiki/Openvpn22ManPage>
2.1 - <https://community.openvpn.net/openvpn/wiki/Openvpn21ManPage#lbAG>
Quoted 4 lines
Man pages still has all of them since that time:
Quoted 3 lines
remote server.exmaple.net
remote server.exmaple.net 1194
remote server.exmaple.net tcp
These lines comes from this commit:
<https://github.com/OpenVPN/openvpn/commit/f500c49c8e0a77ce665b11f6adbea4029cf3b85f>
Where the last line (missing port number) is incorrect.
I also don't see any commit changing the "remote" parsing in options.c in the way you describe. This section has just few changes over the years, but even back to changes 7-12 years ago, the second argument has always been processed as a port number and the third one protocol. Both causing an error if it is not a valid value. So putting protocol in the second argument would trigger an error in 2.1, 2.2, 2.3 and 2.4 as far as I can see.
Quoted 6 lines
At first look there is no need for proto w/o port set, why it can be important? With support of server host & port discovery (DNS SRV RFC 2782), port info is not required, only host and protocol make sense. So I though about this one little step forward toward ~consistent syntax. Does it makes any sense?
I don't see why OpenVPN's --remote parsing needs to comply with DNS SRV RFC standards. How is that related at all? I know we have patches for adding DNS SRV query support, but that doesn't imply passing this information via add_option(), does it?
If you use --remote vpn.example.com --proto tcp .... that will already work. What will not work is --remote vpn.example.com tcp
Also, this will work in config files:
-------------------------------
port 5000
proto udp
<connection>
remote vpn1.example.com
</connection>
<connetion>
remote vpn2.example.com
proto tcp
</connection>
-------------------------------
All of these use cases makes sense, as it depends on a pre-set value. What does not make sense to me is to muddy a pretty clearly defined argument order which has been the standard since the beginning of OpenVPN.
Signature · 4 lines
kind regards, David Sommerseth OpenVPN Inc
Ok, thank you for clarification
--
Best Regards, Vladislav Grishenko
Quoted 115 lines
-----Original Message-----
From: David Sommerseth <[email protected]...>
Sent: Wednesday, September 9, 2020 10:49 PM
To: Vladislav Grishenko <[email protected]...>; openvpn- [email protected]
Subject: Re: [Openvpn-devel] [PATCH] Fix --remote protocol can't be set without port argumentQuoted 31 lines · Vladislav Grishenko
Hi David,
Quoted 29 lines
-----Original Message-----
From: David Sommerseth <[email protected]...>
Sent: Tuesday, September 8, 2020 6:23 PM
To: Vladislav Grishenko <[email protected]...>; openvpn- [email protected]
Subject: Re: [Openvpn-devel] [PATCH] Fix --remote protocol can't be set without port argumentQuoted 3 lines · Vladislav Grishenko
According
client-options.rstadditional argumets ``port`` and ``proto`` are both optional and it's allowed to have port absent and protocolset:
Quoted 4 lines
--remote args
Examples:
remote server.example.net tcpQuoted 8 lines
But when protocol is set without preceeding port argument, it is being misparsed as a port with subsequent error:
RESOLVE: Cannot resolve host address: server.example.net:tcp (Servname not supported forai_socktype)Since protocol names are predefined and don't match service names, fix this behavior by checking second argument for valid protocol first.
Uhm ... I'm leaning towards a NAK to this patch and would rather suggest updating the man page to be correct. This is a mistake from my side when converting the man page to .rst files. The example should be:
Quoted 6 lines
Quoted 2 lines
remote server.example.net 1194 tcp
Hum. Initially all variants were supported, by checking numeric port and taking it as proto, if not numeric. Later port became string servname and optional logic was lost.
The man page history disagrees ... even though, it doesn't say this order is explicit.
2.4 -
<https://community.openvpn.net/openvpn/wiki/Openvpn24ManPage#lbAG>
2.3 -
<https://community.openvpn.net/openvpn/wiki/Openvpn23ManPage#lbAG>
2.2 - <https://community.openvpn.net/openvpn/wiki/Openvpn22ManPage>
2.1 -
<https://community.openvpn.net/openvpn/wiki/Openvpn21ManPage#lbAG>Quoted 4 lines
Man pages still has all of them since that time:
Quoted 3 lines
remote server.exmaple.net
remote server.exmaple.net 1194
remote server.exmaple.net tcpThese lines comes from this commit:
<https://github.com/OpenVPN/openvpn/commit/f500c49c8e0a77ce665b11f6adbea4029cf3b85f>Where the last line (missing port number) is incorrect.
I also don't see any commit changing the "remote" parsing in
options.cin the way you describe. This section has just few changes over the years, but even back to changes 7-12 years ago, the second argument has always been processed as a port number and the third one protocol. Both causing an error if it is not a valid value. So putting protocol in the second argument would trigger an error in 2.1, 2.2, 2.3 and 2.4 as far as I can see.Quoted 6 lines
At first look there is no need for proto w/o port set, why it can be important? With support of server host & port discovery (DNS SRV RFC 2782), port info is not required, only host and protocol make sense. So I though about this one little step forward toward ~consistent syntax. Does it makes any sense?
I don't see why OpenVPN's --remote parsing needs to comply with DNS SRV RFC standards. How is that related at all? I know we have patches for adding DNS SRV query support, but that doesn't imply passing this information via
add_option(), does it?If you use --remote vpn.example.com --proto tcp .... that will already work. What will not work is --remote vpn.example.com tcp
Also, this will work in config files:
-------------------------------
port 5000
proto udp<connection>
remote vpn1.example.com
</connection>
<connetion>
remote vpn2.example.com
proto tcp
</connection>
-------------------------------All of these use cases makes sense, as it depends on a pre-set value. What does not make sense to me is to muddy a pretty clearly defined argument order which has been the standard since the beginning of OpenVPN.
--
kind regards,David Sommerseth
OpenVPN Inc