Skip to contentSkip to conversation

wdt: Add support for watchdogs on Kendryte K210

PATCH Superseded Sean Anderson 3 participants 12 messages Sep 9, 2020 – Nov 4, 2020 1 message not in the archive

Subsystems (2)

v4 of 6 Superseded Latest is v6 →

lore
Share & tools
lore
#0 lore raw

v4 cover wdt: Add support for watchdogs on Kendryte K210

This series depends on
https://patchwork.ozlabs.org/project/uboot/list/?series=200642

Changes in v4:
- Fix build error without CONFIG_CLK

Changes in v3:
- Note dependency on "time: Fix get_ticks being non-monotonic"
- Add a few signed-off-bys which were sent for version 1

Changes in v2:
- Fix fls being off-by-one when compared to log_2_n_round_up
- Move watchdog enable to k210.dtsi as it does not depend on anything board-specific.

Sean Anderson (7):
wdt: dw: Switch to using fls for log2
wdt: dw: Switch to if(CONFIG()) instead of using #if
wdt: dw: Fix clock rate being off by 1000
wdt: dw: Enable the clock before using it
wdt: dw: Free the clock on error
riscv: Add watchdog bindings for the k210
riscv: Enable watchdog for the k210

 arch/riscv/dts/k210.dtsi          |  1 -
 board/sipeed/maix/Kconfig         |  2 ++
 drivers/watchdog/designware_wdt.c | 39 ++++++++++++++++++++-----------
 3 files changed, 27 insertions(+), 15 deletions(-)
Signature · 1 line
2.28.0
#1 lore raw

PATCH v4 1/7 wdt: dw: Switch to using fls for log2

log_2_n_round_up is only found in arm. fls performs the same job and is generic.

---

(no changes since v2)

Changes in v2:
- Fix fls being off-by-one when compared to log_2_n_round_up

 drivers/watchdog/designware_wdt.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/watchdog/designware_wdt.c +1 -2
index 12f09a7a39..f25c8d9ab3 100644
@@ -9,7 +9,6 @@
 #include <reset.h>
 #include <wdt.h>
 #include <asm/io.h>
-#include <asm/utils.h>
 #include <linux/bitops.h>
 
 #define DW_WDT_CR	0x00
@@ -35,7 +34,7 @@ static int designware_wdt_settimeout(void __iomem *base, unsigned int clk_khz,
 	signed int i;
 
 	/* calculate the timeout range value */
-	i = log_2_n_round_up(timeout * clk_khz) - 16;
+	i = fls(timeout * clk_khz - 1) - 16;
 	i = clamp(i, 0, 15);
 
 	writel(i | (i << 4), base + DW_WDT_TORR);
Signature · 1 line
2.28.0
#2 lore raw

PATCH v4 2/7 wdt: dw: Switch to if(CONFIG()) instead of using #if

In reply to Sean Anderson

This is preferred over #if because the compiler can check syntax even if the feature is disabled. This cannot be used for CONFIG_CLK because CONFIG_DW_WDT_CLOCK_KHZ is not defined on all platforms.

---

(no changes since v1)

 drivers/watchdog/designware_wdt.c | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)
drivers/watchdog/designware_wdt.c +9 -9
index f25c8d9ab3..49cf861d46 100644
@@ -136,17 +136,17 @@ static int designware_wdt_probe(struct udevice *dev)
 	priv->clk_khz = CONFIG_DW_WDT_CLOCK_KHZ;
 #endif
 
-#if CONFIG_IS_ENABLED(DM_RESET)
-	struct reset_ctl_bulk resets;
+	if (CONFIG_IS_ENABLED(DM_RESET)) {
+		struct reset_ctl_bulk resets;
 
-	ret = reset_get_bulk(dev, &resets);
-	if (ret)
-		return ret;
+		ret = reset_get_bulk(dev, &resets);
+		if (ret)
+			return ret;
 
-	ret = reset_deassert_bulk(&resets);
-	if (ret)
-		return ret;
-#endif
+		ret = reset_deassert_bulk(&resets);
+		if (ret)
+			return ret;
+	}
 
 	/* reset to disable the watchdog */
 	return designware_wdt_stop(dev);
Signature · 1 line
2.28.0
#3 lore raw

PATCH v4 3/7 wdt: dw: Fix clock rate being off by 1000

In reply to Sean Anderson

The clock subsystem returns clock rates in Hz. We need to divide by 1000 so the rate is in kHz.

Fixes cf89ef8d10f240554541c20b2e1bdcdd58d1d7e6

---

(no changes since v1)

 drivers/watchdog/designware_wdt.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/watchdog/designware_wdt.c +1 -1
index 49cf861d46..41866fa01b 100644
@@ -129,7 +129,7 @@ static int designware_wdt_probe(struct udevice *dev)
 	if (ret)
 		return ret;
 
-	priv->clk_khz = clk_get_rate(&clk);
+	priv->clk_khz = clk_get_rate(&clk) / 1000;
 	if (!priv->clk_khz)
 		return -EINVAL;
 #else
Signature · 1 line
2.28.0
#4 lore raw

PATCH v4 4/7 wdt: dw: Enable the clock before using it

In reply to Sean Anderson

The watchdog won't work if the clock isn't enabled.

Fixes cf89ef8d10f240554541c20b2e1bdcdd58d1d7e6

---

(no changes since v1)

 drivers/watchdog/designware_wdt.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/watchdog/designware_wdt.c +4 -0
index 41866fa01b..e6f5437056 100644
@@ -129,6 +129,10 @@ static int designware_wdt_probe(struct udevice *dev)
 	if (ret)
 		return ret;
 
+	ret = clk_enable(&clk);
+	if (ret)
+		return ret;
+
 	priv->clk_khz = clk_get_rate(&clk) / 1000;
 	if (!priv->clk_khz)
 		return -EINVAL;
Signature · 1 line
2.28.0
#5 lore raw

PATCH v4 5/7 wdt: dw: Free the clock on error

In reply to Sean Anderson

The clock subsystem requires that clk_free be called on clocks obtained via clk_get_*.

---

Changes in v4:
- Fix build error without CONFIG_CLK

 drivers/watchdog/designware_wdt.c | 18 +++++++++++++-----
 1 file changed, 13 insertions(+), 5 deletions(-)
drivers/watchdog/designware_wdt.c +13 -5
index e6f5437056..b952737fb4 100644
@@ -131,11 +131,13 @@ static int designware_wdt_probe(struct udevice *dev)
 
 	ret = clk_enable(&clk);
 	if (ret)
-		return ret;
+		goto err;
 
 	priv->clk_khz = clk_get_rate(&clk) / 1000;
-	if (!priv->clk_khz)
-		return -EINVAL;
+	if (!priv->clk_khz) {
+		ret = -EINVAL;
+		goto err;
+	}
 #else
 	priv->clk_khz = CONFIG_DW_WDT_CLOCK_KHZ;
 #endif
@@ -145,15 +147,21 @@ static int designware_wdt_probe(struct udevice *dev)
 
 		ret = reset_get_bulk(dev, &resets);
 		if (ret)
-			return ret;
+			goto err;
 
 		ret = reset_deassert_bulk(&resets);
 		if (ret)
-			return ret;
+			goto err;
 	}
 
 	/* reset to disable the watchdog */
 	return designware_wdt_stop(dev);
+
+err:
+#if CONFIG_IS_ENABLED(CLK)
+	clk_free(&clk);
+#endif
+	return ret;
 }
 
 static const struct wdt_ops designware_wdt_ops = {
Signature · 1 line
2.28.0
#6 lore raw

PATCH v4 6/7 riscv: Add watchdog bindings for the k210

In reply to Sean Anderson

This adds the necessary bindings. Most of them are already there.

---

(no changes since v2)

Changes in v2:
- Move watchdog enable to k210.dtsi as it does not depend on anything board-specific.

 arch/riscv/dts/k210.dtsi | 1 -
 1 file changed, 1 deletion(-)
arch/riscv/dts/k210.dtsi +0 -1
index 84cff51c36..81ac417dde 100644
@@ -426,7 +426,6 @@
 				interrupts = <21>;
 				clocks = <&sysclk K210_CLK_WDT0>;
 				resets = <&sysrst K210_RST_WDT0>;
-				status = "disabled";
 			};
 
 			wdt1: watchdog at 50410000 {
Signature · 1 line
2.28.0
#7 lore raw

PATCH v4 7/7 riscv: Enable watchdog for the k210

In reply to Sean Anderson

This enables the necessary config options.

---

(no changes since v3)

Changes in v3:
- Note dependency on "time: Fix get_ticks being non-monotonic"
- Add a few signed-off-bys which were sent for version 1

 board/sipeed/maix/Kconfig | 2 ++
 1 file changed, 2 insertions(+)
board/sipeed/maix/Kconfig +2 -0
index 0cdcd32adc..b9dac5a64e 100644
@@ -44,4 +44,6 @@ config BOARD_SPECIFIC_OPTIONS
 	imply RESET_SYSCON
 	imply SYSRESET
 	imply SYSRESET_SYSCON
+	imply WDT
+	imply DESIGNWARE_WATCHDOG
 endif
Signature · 1 line
2.28.0
#8 lore raw

v4 cover wdt: Add support for watchdogs on Kendryte K210

In reply to Sean Anderson
Quoted 24 lines · Sean Anderson

This series depends on
https://patchwork.ozlabs.org/project/uboot/list/?series=200642

Changes in v4:
- Fix build error without CONFIG_CLK

Changes in v3:
- Note dependency on "time: Fix get_ticks being non-monotonic"
- Add a few signed-off-bys which were sent for version 1

Changes in v2:
- Fix fls being off-by-one when compared to log_2_n_round_up
- Move watchdog enable to k210.dtsi as it does not depend on anything board-specific.

Sean Anderson (7):
wdt: dw: Switch to using fls for log2
wdt: dw: Switch to if(CONFIG()) instead of using #if
wdt: dw: Fix clock rate being off by 1000
wdt: dw: Enable the clock before using it
wdt: dw: Free the clock on error
riscv: Add watchdog bindings for the k210
riscv: Enable watchdog for the k210

Quoted 5 lines
 arch/riscv/dts/k210.dtsi          |  1 -
 board/sipeed/maix/Kconfig         |  2 ++
 drivers/watchdog/designware_wdt.c | 39 ++++++++++++++++++++-----------
 3 files changed, 27 insertions(+), 15 deletions(-)

*ping*

Marek can these go into -next?

--Sean

#9 lore raw

v4 cover wdt: Add support for watchdogs on Kendryte K210

Quoted 31 lines · Sean Anderson
Quoted 24 lines · Sean Anderson

This series depends on
https://patchwork.ozlabs.org/project/uboot/list/?series=200642

Changes in v4:
- Fix build error without CONFIG_CLK

Changes in v3:
- Note dependency on "time: Fix get_ticks being non-monotonic"
- Add a few signed-off-bys which were sent for version 1

Changes in v2:
- Fix fls being off-by-one when compared to log_2_n_round_up
- Move watchdog enable to k210.dtsi as it does not depend on anything board-specific.

Sean Anderson (7):
wdt: dw: Switch to using fls for log2
wdt: dw: Switch to if(CONFIG()) instead of using #if
wdt: dw: Fix clock rate being off by 1000
wdt: dw: Enable the clock before using it
wdt: dw: Free the clock on error
riscv: Add watchdog bindings for the k210
riscv: Enable watchdog for the k210

Quoted 5 lines
 arch/riscv/dts/k210.dtsi          |  1 -
 board/sipeed/maix/Kconfig         |  2 ++
 drivers/watchdog/designware_wdt.c | 39 ++++++++++++++++++++-----------
 3 files changed, 27 insertions(+), 15 deletions(-)
Quoted 6 lines

*ping*

Marek can these go into -next?

--Sean

*second ping*

It appears that an earlier version of this series [1] was assigned to Marek Vasut, but that the current version is assigned to Rick Chen. v2 should be marked as superseded. Can this get picked up for the merge window?

--Sean

[1] https://patchwork.ozlabs.org/project/uboot/list/?series=194673
[2] https://patchwork.ozlabs.org/project/uboot/list/?series=200657

#10 lore raw

v4 cover wdt: Add support for watchdogs on Kendryte K210

Quoted 40 lines · Sean Anderson
Quoted 31 lines · Sean Anderson
Quoted 24 lines · Sean Anderson

This series depends on
https://patchwork.ozlabs.org/project/uboot/list/?series=200642

Changes in v4:
- Fix build error without CONFIG_CLK

Changes in v3:
- Note dependency on "time: Fix get_ticks being non-monotonic"
- Add a few signed-off-bys which were sent for version 1

Changes in v2:
- Fix fls being off-by-one when compared to log_2_n_round_up
- Move watchdog enable to k210.dtsi as it does not depend on anything board-specific.

Sean Anderson (7):
wdt: dw: Switch to using fls for log2
wdt: dw: Switch to if(CONFIG()) instead of using #if
wdt: dw: Fix clock rate being off by 1000
wdt: dw: Enable the clock before using it
wdt: dw: Free the clock on error
riscv: Add watchdog bindings for the k210
riscv: Enable watchdog for the k210

Quoted 5 lines
 arch/riscv/dts/k210.dtsi          |  1 -
 board/sipeed/maix/Kconfig         |  2 ++
 drivers/watchdog/designware_wdt.c | 39 ++++++++++++++++++++-----------
 3 files changed, 27 insertions(+), 15 deletions(-)
Quoted 6 lines

*ping*

Marek can these go into -next?

--Sean

Quoted 6 lines

*second ping*

It appears that an earlier version of this series [1] was assigned to Marek Vasut, but that the current version is assigned to Rick Chen. v2 should be marked as superseded. Can this get picked up for the merge window?

The v2 mess-up was me, probably, some typo or another. For v4, it looks fine to me. Rick?

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20201026/84ab3e46/attachment-0001.sig>

A message that is not in the archive (sent off-list or not yet received): [email protected]

#12 lore raw

v4 cover wdt: Add support for watchdogs on Kendryte K210

<[email protected]> ? 2020?11?4? ?? ??10:01???

Quoted 50 lines

-----Original Message-----
From: U-Boot [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Sean Anderson
Sent: Friday, October 23, 2020 9:30 PM
To: u-boot at lists.denx.de
Cc: Bin Meng; Marek Vasut; Jagan Teki; Simon Glass; Heinrich Schuchardt
Subject: Re: [PATCH v4 0/7] wdt: Add support for watchdogs on Kendryte K210

Quoted 31 lines · Sean Anderson
Quoted 24 lines · Sean Anderson

This series depends on
https://patchwork.ozlabs.org/project/uboot/list/?series=200642

Changes in v4:
- Fix build error without CONFIG_CLK

Changes in v3:
- Note dependency on "time: Fix get_ticks being non-monotonic"
- Add a few signed-off-bys which were sent for version 1

Changes in v2:
- Fix fls being off-by-one when compared to log_2_n_round_up
- Move watchdog enable to k210.dtsi as it does not depend on anything board-specific.

Sean Anderson (7):
wdt: dw: Switch to using fls for log2
wdt: dw: Switch to if(CONFIG()) instead of using #if
wdt: dw: Fix clock rate being off by 1000
wdt: dw: Enable the clock before using it
wdt: dw: Free the clock on error
riscv: Add watchdog bindings for the k210
riscv: Enable watchdog for the k210

Quoted 5 lines
 arch/riscv/dts/k210.dtsi          |  1 -
 board/sipeed/maix/Kconfig         |  2 ++
 drivers/watchdog/designware_wdt.c | 39 ++++++++++++++++++++-----------
 3 files changed, 27 insertions(+), 15 deletions(-)
Quoted 6 lines

*ping*

Marek can these go into -next?

--Sean

Quoted 6 lines

*second ping*

It appears that an earlier version of this series [1] was assigned to Marek Vasut, but that the current version is assigned to Rick Chen. v2 should be marked as superseded. Can this get picked up for the merge window?

Those patchs seem have been reviewed and tagged.
If no other comments furthermore.
I can help to pull via riscv tree later.

But it shall sync to master again:
Applying: wdt: dw: Switch to using fls for log2
Applying: wdt: dw: Switch to if(CONFIG()) instead of using #if
Applying: wdt: dw: Fix clock rate being off by 1000
error: patch failed: drivers/watchdog/designware_wdt.c:129
error: drivers/watchdog/designware_wdt.c: patch does not apply Patch failed at 0003 wdt: dw: Fix clock rate being off by 1000

Thanks,
Rick

Quoted 5 lines

--Sean

[1] https://patchwork.ozlabs.org/project/uboot/list/?series=194673
[2] https://patchwork.ozlabs.org/project/uboot/list/?series=200657