mx6qsabrelite: increase offset for environment on SPI
PATCH 1/1 mx6qsabrelite: increase offset for environment on SPI
The size of the binary created with the default U-boot config is much greater than the default offset for environment 0x60000. If the new version is flashed onto SPI it overlaps with the stored environment. This leads to U-Boot corruption in case of saving environment onto SPI and non-bootable SabreLite board.
--- configs/mx6qsabrelite_defconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
configs/mx6qsabrelite_defconfig +1 -1
@@ -4,7 +4,7 @@ CONFIG_SYS_TEXT_BASE=0x17800000 CONFIG_SYS_MALLOC_F_LEN=0x4000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x60000 +CONFIG_ENV_OFFSET=0xC0000 CONFIG_MX6Q=y CONFIG_TARGET_NITROGEN6X=y CONFIG_DM_GPIO=y
Signature · 1 line
2.25.4
PATCH 1/1 mx6qsabrelite: increase offset for environment on SPI
Quoted 17 lines · Denis Pynkin
The size of the binary created with the default U-boot config is much greater than the default offset for environment
0x60000. If the new version is flashed onto SPI it overlaps with the stored environment. This leads to U-Boot corruption in case of saving environment onto SPI and non-bootable SabreLite board.Signed-off-by Denis Pynkin <[email protected]>--- configs/mx6qsabrelite_defconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)configs/mx6qsabrelite_defconfig +0
-0
configs/mx6qsabrelite_defconfig CONFIG_SYS_TEXT_BASE=0x17800000 · line 10
Quoted 8 lines
configs/mx6qsabrelite_defconfig +1
-1@@ -4,7 +4,7 @@ CONFIG_SYS_TEXT_BASE=0x17800000 CONFIG_SYS_MALLOC_F_LEN=0x4000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x60000 +CONFIG_ENV_OFFSET=0xC0000 CONFIG_MX6Q=y CONFIG_TARGET_NITROGEN6X=y CONFIG_DM_GPIO=y
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH 1/1 mx6qsabrelite: increase offset for environment on SPI
In reply to Denis PynkinHi Denis,
Quoted 8 lines · Denis Pynkin
The size of the binary created with the default U-boot config is much greater than the default offset for environment
0x60000. If the new version is flashed onto SPI it overlaps with the stored environment. This leads to U-Boot corruption in case of saving environment onto SPI and non-bootable SabreLite board.Signed-off-by Denis Pynkin <[email protected]>
In case you want to detect errors like this again in the future, you could add CONFIG_BOARD_SIZE_LIMIT that detects such overlaps in build-time.
Please check commit 033f6ea5fa5f ("mx53loco: Fix U-Boot corruption after saving the environment")
The addition of CONFIG_BOARD_SIZE_LIMIT can be a separate patch though.
PATCH 1/1 mx6qsabrelite: increase offset for environment on SPI
Quoted 14 lines · Fabio Estevam
Hi Denis,
Quoted 8 lines · Denis Pynkin
The size of the binary created with the default U-boot config is much greater than the default offset for environment
0x60000. If the new version is flashed onto SPI it overlaps with the stored environment. This leads to U-Boot corruption in case of saving environment onto SPI and non-bootable SabreLite board.Signed-off-by Denis Pynkin <[email protected]>Reviewed-by Fabio Estevam <[email protected]>
Quoted 7 lines
In case you want to detect errors like this again in the future, you could add
CONFIG_BOARD_SIZE_LIMITthat detects such overlaps in build-time.Please check commit
033f6ea5fa5f("mx53loco: Fix U-Boot corruption after saving the environment")The addition of
CONFIG_BOARD_SIZE_LIMITcan be a separate patch though.
Hold on. Can we shrink the board back down so that we don't need to move the environment? Moving the environment is bad as it will also break existing users. Thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200914/76207c23/attachment.sig>
PATCH 1/1 mx6qsabrelite: increase offset for environment on SPI
14.09.2020 15:33, Tom Rini wrote?:
Quoted 15 lines · Fabio Estevam
Quoted 14 lines
Quoted 8 lines
The size of the binary created with the default U-boot config is much greater than the default offset for environment
0x60000. If the new version is flashed onto SPI it overlaps with the stored environment. This leads to U-Boot corruption in case of saving environment onto SPI and non-bootable SabreLite board.Signed-off-by Denis Pynkin <[email protected]>Reviewed-by Fabio Estevam <[email protected]>In case you want to detect errors like this again in the future, you could add
CONFIG_BOARD_SIZE_LIMITthat detects such overlaps in build-time.
Quoted 8 lines
Quoted 4 lines
Please check commit
033f6ea5fa5f("mx53loco: Fix U-Boot corruption after saving the environment")The addition of
CONFIG_BOARD_SIZE_LIMITcan be a separate patch though.Hold on. Can we shrink the board back down so that we don't need to move the environment? Moving the environment is bad as it will also break existing users. Thanks!
I don't think so to be honest.
Current sizes even for u-boot-nodtb.imx in my builds are:
- 595308 (0x9156C) -- cross-compilation
- 470780 (0x72EFC) -- native build
which is much larger than current offset 393216 (0x60000)
The offset for environment CONFIG_ENV_OFFSET=0x60000 were added in commit a09fea1 just a year ago.
Not sure if it was tested with SabreLite board tbh -- this is a bulk commit aimed for ARMv8 and sizes of binaries produced with pre-a09fea1 commit are also larger than the current offset.
Signature · 1 line
wbr, Denis
PATCH 1/1 mx6qsabrelite: increase offset for environment on SPI
Quoted 21 lines · Denis Pynkin
14.09.2020 15:33, Tom Rini wrote?:
Quoted 20 lines · Fabio Estevam
Quoted 18 lines
Quoted 8 lines
The size of the binary created with the default U-boot config is much greater than the default offset for environment
0x60000. If the new version is flashed onto SPI it overlaps with the stored environment. This leads to U-Boot corruption in case of saving environment onto SPI and non-bootable SabreLite board.Signed-off-by Denis Pynkin <[email protected]>Reviewed-by Fabio Estevam <[email protected]>In case you want to detect errors like this again in the future, you could add
CONFIG_BOARD_SIZE_LIMITthat detects such overlaps in build-time.Please check commit
033f6ea5fa5f("mx53loco: Fix U-Boot corruption after saving the environment")The addition of
CONFIG_BOARD_SIZE_LIMITcan be a separate patch though.
Quoted 8 lines
Quoted 3 lines
Hold on. Can we shrink the board back down so that we don't need to move the environment? Moving the environment is bad as it will also break existing users. Thanks!
I don't think so to be honest.
Current sizes even foru-boot-nodtb.imxin my builds are:
- 595308 (0x9156C) -- cross-compilation
- 470780 (0x72EFC) -- native build
I'd like to have one thread where we see what on earth is going on there. That's a rather crazy size difference and very troubling.
Quoted 7 lines
which is much larger than current offset 393216 (
0x60000)The offset for environment
CONFIG_ENV_OFFSET=0x60000were added in commit a09fea1 just a year ago.
Not sure if it was tested with SabreLite board tbh -- this is a bulk commit aimed for ARMv8 and sizes of binaries produced with pre-a09fea1 commit are also larger than the current offset.
Ah, so here's what's going on then. Commit a09fea1 wasn't about ARMv8, it was about migrating options to the defconfig files. In this case, it should have been set to the value you're changing it to now, at least from a read of the patch (include/configs/mx6sabre_common.h would set it to 0xC0000 if CONFIG_ENV_IS_IN_MMC), but I thought I had done that migration with my hack to make a tool that had the in-use value be printed. So I'm going to re-check that whole thing to see what else might be wrong as well. Thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200914/8ada3a7b/attachment.sig>
PATCH 1/1 mx6qsabrelite: increase offset for environment on SPI
Quoted 42 lines · Tom Rini
Quoted 21 lines · Denis Pynkin
14.09.2020 15:33, Tom Rini wrote?:
Quoted 20 lines · Fabio Estevam
Quoted 18 lines
Quoted 8 lines
The size of the binary created with the default U-boot config is much greater than the default offset for environment
0x60000. If the new version is flashed onto SPI it overlaps with the stored environment. This leads to U-Boot corruption in case of saving environment onto SPI and non-bootable SabreLite board.Signed-off-by Denis Pynkin <[email protected]>Reviewed-by Fabio Estevam <[email protected]>In case you want to detect errors like this again in the future, you could add
CONFIG_BOARD_SIZE_LIMITthat detects such overlaps in build-time.Please check commit
033f6ea5fa5f("mx53loco: Fix U-Boot corruption after saving the environment")The addition of
CONFIG_BOARD_SIZE_LIMITcan be a separate patch though.Quoted 8 lines
Quoted 3 lines
Hold on. Can we shrink the board back down so that we don't need to move the environment? Moving the environment is bad as it will also break existing users. Thanks!
I don't think so to be honest.
Current sizes even foru-boot-nodtb.imxin my builds are:
- 595308 (0x9156C) -- cross-compilation
- 470780 (0x72EFC) -- native buildI'd like to have one thread where we see what on earth is going on there. That's a rather crazy size difference and very troubling.
Quoted 7 lines
which is much larger than current offset 393216 (
0x60000)The offset for environment
CONFIG_ENV_OFFSET=0x60000were added in commit a09fea1 just a year ago.
Not sure if it was tested with SabreLite board tbh -- this is a bulk commit aimed for ARMv8 and sizes of binaries produced with pre-a09fea1 commit are also larger than the current offset.
Quoted 8 lines
Ah, so here's what's going on then. Commit a09fea1 wasn't about ARMv8, it was about migrating options to the defconfig files. In this case, it should have been set to the value you're changing it to now, at least from a read of the patch (
include/configs/mx6sabre_common.hwould set it to0xC0000ifCONFIG_ENV_IS_IN_MMC), but I thought I had done that migration with my hack to make a tool that had the in-use value be printed. So I'm going to re-check that whole thing to see what else might be wrong as well. Thanks!
Ah, so, mx6qsabrelite falls in to the "nitrogen6x" family and not the rest of the "sabre" board families. As such, it's always had the env offset of 0x60000. Jumping back somewhat arbitrarily to v2014.10, I see with gcc-4.9 a size of 404480 on u-boot.imx which is still bigger.
The commit message isn't clear however, as environment is in MMC and not SPI, so SPI booting should be fine. But MMC/eMMC is where this case can happen (I'm not sure which device is SD slot and which is eMMC on this hardware off-hand). Thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200914/190444d7/attachment.sig>
PATCH 1/1 mx6qsabrelite: increase offset for environment on SPI
Quoted 57 lines · Tom Rini
Quoted 42 lines · Tom Rini
Quoted 21 lines · Denis Pynkin
14.09.2020 15:33, Tom Rini wrote?:
Quoted 20 lines · Fabio Estevam
Quoted 18 lines
Quoted 8 lines
The size of the binary created with the default U-boot config is much greater than the default offset for environment
0x60000. If the new version is flashed onto SPI it overlaps with the stored environment. This leads to U-Boot corruption in case of saving environment onto SPI and non-bootable SabreLite board.Signed-off-by Denis Pynkin <[email protected]>Reviewed-by Fabio Estevam <[email protected]>In case you want to detect errors like this again in the future, you could add
CONFIG_BOARD_SIZE_LIMITthat detects such overlaps in build-time.Please check commit
033f6ea5fa5f("mx53loco: Fix U-Boot corruption after saving the environment")The addition of
CONFIG_BOARD_SIZE_LIMITcan be a separate patch though.Quoted 8 lines
Quoted 3 lines
Hold on. Can we shrink the board back down so that we don't need to move the environment? Moving the environment is bad as it will also break existing users. Thanks!
I don't think so to be honest.
Current sizes even foru-boot-nodtb.imxin my builds are:
- 595308 (0x9156C) -- cross-compilation
- 470780 (0x72EFC) -- native buildI'd like to have one thread where we see what on earth is going on there. That's a rather crazy size difference and very troubling.
Quoted 7 lines
which is much larger than current offset 393216 (
0x60000)The offset for environment
CONFIG_ENV_OFFSET=0x60000were added in commit a09fea1 just a year ago.
Not sure if it was tested with SabreLite board tbh -- this is a bulk commit aimed for ARMv8 and sizes of binaries produced with pre-a09fea1 commit are also larger than the current offset.Quoted 8 lines
Ah, so here's what's going on then. Commit a09fea1 wasn't about ARMv8, it was about migrating options to the defconfig files. In this case, it should have been set to the value you're changing it to now, at least from a read of the patch (
include/configs/mx6sabre_common.hwould set it to0xC0000ifCONFIG_ENV_IS_IN_MMC), but I thought I had done that migration with my hack to make a tool that had the in-use value be printed. So I'm going to re-check that whole thing to see what else might be wrong as well. Thanks!Ah, so, mx6qsabrelite falls in to the "nitrogen6x" family and not the rest of the "sabre" board families. As such, it's always had the env offset of
0x60000. Jumping back somewhat arbitrarily to v2014.10, I see with gcc-4.9 a size of 404480 on u-boot.imx which is still bigger.
Quoted 4 lines
The commit message isn't clear however, as environment is in MMC and not SPI, so SPI booting should be fine. But MMC/eMMC is where this case can happen (I'm not sure which device is SD slot and which is eMMC on this hardware off-hand). Thanks!
To my shame -- I didn't even thought about the booting from MMC, but yes -- should be the same issue in case if U-Boot is placed on SD-card.
This device have 2MB SPI NOR flash there the U-Boot could be flashed with an environment. We are using this approach, so I attempt to describe the issue from this point of view.
Should I try to re-word the description? Or may I ask you to add a better description?
Signature · 1 line
wbr, Denis
PATCH 1/1 mx6qsabrelite: increase offset for environment on SPI
Quoted 66 lines · Denis Pynkin
Quoted 57 lines · Tom Rini
Quoted 42 lines · Tom Rini
Quoted 21 lines · Denis Pynkin
14.09.2020 15:33, Tom Rini wrote?:
Quoted 20 lines · Fabio Estevam
Quoted 18 lines
Quoted 8 lines
The size of the binary created with the default U-boot config is much greater than the default offset for environment
0x60000. If the new version is flashed onto SPI it overlaps with the stored environment. This leads to U-Boot corruption in case of saving environment onto SPI and non-bootable SabreLite board.Signed-off-by Denis Pynkin <[email protected]>Reviewed-by Fabio Estevam <[email protected]>In case you want to detect errors like this again in the future, you could add
CONFIG_BOARD_SIZE_LIMITthat detects such overlaps in build-time.Please check commit
033f6ea5fa5f("mx53loco: Fix U-Boot corruption after saving the environment")The addition of
CONFIG_BOARD_SIZE_LIMITcan be a separate patch though.Quoted 8 lines
Quoted 3 lines
Hold on. Can we shrink the board back down so that we don't need to move the environment? Moving the environment is bad as it will also break existing users. Thanks!
I don't think so to be honest.
Current sizes even foru-boot-nodtb.imxin my builds are:
- 595308 (0x9156C) -- cross-compilation
- 470780 (0x72EFC) -- native buildI'd like to have one thread where we see what on earth is going on there. That's a rather crazy size difference and very troubling.
Quoted 7 lines
which is much larger than current offset 393216 (
0x60000)The offset for environment
CONFIG_ENV_OFFSET=0x60000were added in commit a09fea1 just a year ago.
Not sure if it was tested with SabreLite board tbh -- this is a bulk commit aimed for ARMv8 and sizes of binaries produced with pre-a09fea1 commit are also larger than the current offset.Quoted 8 lines
Ah, so here's what's going on then. Commit a09fea1 wasn't about ARMv8, it was about migrating options to the defconfig files. In this case, it should have been set to the value you're changing it to now, at least from a read of the patch (
include/configs/mx6sabre_common.hwould set it to0xC0000ifCONFIG_ENV_IS_IN_MMC), but I thought I had done that migration with my hack to make a tool that had the in-use value be printed. So I'm going to re-check that whole thing to see what else might be wrong as well. Thanks!Ah, so, mx6qsabrelite falls in to the "nitrogen6x" family and not the rest of the "sabre" board families. As such, it's always had the env offset of
0x60000. Jumping back somewhat arbitrarily to v2014.10, I see with gcc-4.9 a size of 404480 on u-boot.imx which is still bigger.Quoted 4 lines
The commit message isn't clear however, as environment is in MMC and not SPI, so SPI booting should be fine. But MMC/eMMC is where this case can happen (I'm not sure which device is SD slot and which is eMMC on this hardware off-hand). Thanks!
To my shame -- I didn't even thought about the booting from MMC, but yes -- should be the same issue in case if U-Boot is placed on SD-card.
Quoted 6 lines
This device have 2MB SPI NOR flash there the U-Boot could be flashed with an environment. We are using this approach, so I attempt to describe the issue from this point of view.
Should I try to re-word the description? Or may I ask you to add a better description?
Well, there's a few things going on here then. The defconfig has ENV_IS_IN_MMC, not ENV_IS_IN_SPI. So SPI booting should be fine we're putting U-Boot and environment on entirely different media. There's no conflict. Booting from the first MMC device can be broken as that's where we say the environment should be and 'saveenv' will scribble all over it. So can you confirm what the breaking condition you see is? The commit message talks about SPI, but SPI should work as-is.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200914/b1a8d569/attachment.sig>
PATCH 1/1 mx6qsabrelite: increase offset for environment on SPI
Quoted 74 lines · Tom Rini
Quoted 66 lines · Denis Pynkin
Quoted 57 lines · Tom Rini
Quoted 42 lines · Tom Rini
Quoted 21 lines · Denis Pynkin
14.09.2020 15:33, Tom Rini wrote?:
Quoted 20 lines · Fabio Estevam
Quoted 18 lines
Quoted 8 lines
The size of the binary created with the default U-boot config is much greater than the default offset for environment
0x60000. If the new version is flashed onto SPI it overlaps with the stored environment. This leads to U-Boot corruption in case of saving environment onto SPI and non-bootable SabreLite board.Signed-off-by Denis Pynkin <[email protected]>Reviewed-by Fabio Estevam <[email protected]>In case you want to detect errors like this again in the future, you could add
CONFIG_BOARD_SIZE_LIMITthat detects such overlaps in build-time.Please check commit
033f6ea5fa5f("mx53loco: Fix U-Boot corruption after saving the environment")The addition of
CONFIG_BOARD_SIZE_LIMITcan be a separate patch though.Quoted 8 lines
Quoted 3 lines
Hold on. Can we shrink the board back down so that we don't need to move the environment? Moving the environment is bad as it will also break existing users. Thanks!
I don't think so to be honest.
Current sizes even foru-boot-nodtb.imxin my builds are:
- 595308 (0x9156C) -- cross-compilation
- 470780 (0x72EFC) -- native buildI'd like to have one thread where we see what on earth is going on there. That's a rather crazy size difference and very troubling.
Quoted 7 lines
which is much larger than current offset 393216 (
0x60000)The offset for environment
CONFIG_ENV_OFFSET=0x60000were added in commit a09fea1 just a year ago.
Not sure if it was tested with SabreLite board tbh -- this is a bulk commit aimed for ARMv8 and sizes of binaries produced with pre-a09fea1 commit are also larger than the current offset.Quoted 8 lines
Ah, so here's what's going on then. Commit a09fea1 wasn't about ARMv8, it was about migrating options to the defconfig files. In this case, it should have been set to the value you're changing it to now, at least from a read of the patch (
include/configs/mx6sabre_common.hwould set it to0xC0000ifCONFIG_ENV_IS_IN_MMC), but I thought I had done that migration with my hack to make a tool that had the in-use value be printed. So I'm going to re-check that whole thing to see what else might be wrong as well. Thanks!Ah, so, mx6qsabrelite falls in to the "nitrogen6x" family and not the rest of the "sabre" board families. As such, it's always had the env offset of
0x60000. Jumping back somewhat arbitrarily to v2014.10, I see with gcc-4.9 a size of 404480 on u-boot.imx which is still bigger.Quoted 4 lines
The commit message isn't clear however, as environment is in MMC and not SPI, so SPI booting should be fine. But MMC/eMMC is where this case can happen (I'm not sure which device is SD slot and which is eMMC on this hardware off-hand). Thanks!
To my shame -- I didn't even thought about the booting from MMC, but yes -- should be the same issue in case if U-Boot is placed on SD-card.
Quoted 6 lines
This device have 2MB SPI NOR flash there the U-Boot could be flashed with an environment. We are using this approach, so I attempt to describe the issue from this point of view.
Should I try to re-word the description? Or may I ask you to add a better description?
Quoted 7 lines
Well, there's a few things going on here then. The defconfig has
ENV_IS_IN_MMC, notENV_IS_IN_SPI. So SPI booting should be fine we're putting U-Boot and environment on entirely different media. There's no conflict. Booting from the first MMC device can be broken as that's where we say the environment should be and 'saveenv' will scribble all over it. So can you confirm what the breaking condition you see is? The commit message talks about SPI, but SPI should work as-is.
You are absolutely right.
My fault -- copy-paste the patch from my project as is without additional testing.
Did an additional tests with default value 0x60000:
- works well with the combination U-Boot on SPI NOR flash + environment on MMC
- corrupted U-Boot on MMC after saveenv if used U-Boot on MMC
- corrupted U-Boot after saveenv if it is configured
with CONFIG_ENV_IS_IN_SPI_FLASH=y and flashed on SPI
The value 0xC0000 fixes the issue for both corrupted cases.
Thanks a lot for pointing to incorrect description and misunderstanding!
Signature · 1 line
wbr, Denis
PATCH v2 1/1 mx6qsabrelite: increase the environment offset
The size of the binary created with the default U-boot config is much greater than the default offset for environment 0x60000. In case if that binary is used for booting via MMC it is overlapped with the environment stored on MMC.
This leads to U-Boot corruption while saving environment with saveenv command and non-bootable SabreLite board.
The offset for environment CONFIG_ENV_OFFSET=0x60000 was added in commit a09fea1 but did not count in the change to 0xC0000 if option CONFIG_ENV_IS_IN_MMC is used.
The offset is also used for variant with environment saving onto SPI NOR flash (with enabled option CONFIG_ENV_IS_IN_SPI_FLASH). In that case the U-Boot binary flashed on SPI NOR is also corrupted after environment saving with the original 0x60000 offset.
--- configs/mx6qsabrelite_defconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
configs/mx6qsabrelite_defconfig +1 -1
@@ -4,7 +4,7 @@ CONFIG_SYS_TEXT_BASE=0x17800000 CONFIG_SYS_MALLOC_F_LEN=0x4000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x60000 +CONFIG_ENV_OFFSET=0xC0000 CONFIG_MX6Q=y CONFIG_TARGET_NITROGEN6X=y CONFIG_DM_GPIO=y
Signature · 1 line
2.25.4
PATCH v2 1/1 mx6qsabrelite: increase the environment offset
Quoted 11 lines · Denis Pynkin
The size of the binary created with the default U-boot config is much greater than the default offset for environment
0x60000. In case if that binary is used for booting via MMC it is overlapped with the environment stored on MMC.
This leads to U-Boot corruption while saving environment withsaveenvcommand and non-bootable SabreLite board.The offset for environment
CONFIG_ENV_OFFSET=0x60000was added in commit a09fea1 but did not count in the change to0xC0000if optionCONFIG_ENV_IS_IN_MMCis used.
Quoted 6 lines
The offset is also used for variant with environment saving onto SPI NOR flash (with enabled option
CONFIG_ENV_IS_IN_SPI_FLASH). In that case the U-Boot binary flashed on SPI NOR is also corrupted after environment saving with the original0x60000offset.Signed-off-by Denis Pynkin <[email protected]>
Thanks for rewording.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200915/0ce4521e/attachment.sig>
PATCH v2 1/1 mx6qsabrelite: increase the environment offset
In reply to Denis PynkinQuoted 13 lines
The size of the binary created with the default U-boot config is much greater than the default offset for environment
0x60000.
In case if that binary is used for booting via MMC it is overlapped with the environment stored on MMC.
This leads to U-Boot corruption while saving environment withsaveenvcommand and non-bootable SabreLite board.
The offset for environmentCONFIG_ENV_OFFSET=0x60000was added in commit a09fea1 but did not count in the change to0xC0000if optionCONFIG_ENV_IS_IN_MMCis used.
The offset is also used for variant with environment saving onto SPI NOR flash (with enabled optionCONFIG_ENV_IS_IN_SPI_FLASH). In that case the U-Boot binary flashed on SPI NOR is also corrupted after environment saving with the original0x60000offset.
Quoted 2 lines
Signed-off-by Denis Pynkin <[email protected]>Reviewed-by Tom Rini <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================