Skip to contentSkip to conversation

drivers/net/wan/hdlc: Set skb->protocol before transmitting

PATCH Applied Xie He 2 participants 2 messages Sep 16, 2020 – Sep 17, 2020

Subsystems (3)
lore
Share & tools
lore

Xie He

author
#0 lore raw

PATCH 1/1 drivers/net/wan/hdlc: Set skb->protocol before transmitting

This patch sets skb->protocol before transmitting frames on the HDLC device, so that a user listening on the HDLC device with an AF_PACKET socket will see outgoing frames' sll_protocol field correctly set and consistent with that of incoming frames.

1. Control frames in hdlc_cisco and hdlc_ppp

When these drivers send control frames, skb->protocol is not set.

This value should be set to htons(ETH_P_HDLC), because when receiving control frames, their skb->protocol is set to htons(ETH_P_HDLC).

When receiving, hdlc_type_trans in hdlc.h is called, which then calls cisco_type_trans or ppp_type_trans. The skb->protocol of control frames is set to htons(ETH_P_HDLC) so that the control frames can be received by hdlc_rcv in hdlc.c, which calls cisco_rx or ppp_rx to process the control frames.

2. hdlc_fr

When this driver sends control frames, skb->protocol is set to internal values used in this driver.

When this driver sends data frames (from upper stacked PVC devices), skb->protocol is the same as that of the user data packet being sent on the upper PVC device (for normal PVC devices), or is htons(ETH_P_802_3) (for Ethernet-emulating PVC devices).

However, skb->protocol for both control frames and data frames should be set to htons(ETH_P_HDLC), because when receiving, all frames received on the HDLC device will have their skb->protocol set to htons(ETH_P_HDLC).

When receiving, hdlc_type_trans in hdlc.h is called, and because this driver doesn't provide a type_trans function in struct hdlc_proto, all frames will have their skb->protocol set to htons(ETH_P_HDLC). The frames are then received by hdlc_rcv in hdlc.c, which calls fr_rx to process the frames (control frames are consumed and data frames are re-received on upper PVC devices).

Cc Krzysztof Halasa <[email protected]>
---
 drivers/net/wan/hdlc_cisco.c | 1 +
 drivers/net/wan/hdlc_fr.c    | 3 +++
 drivers/net/wan/hdlc_ppp.c   | 1 +
 3 files changed, 5 insertions(+)
drivers/net/wan/hdlc_cisco.c +1 -0
index 444130655d8e..cb5898f7d68c 100644
@@ -118,6 +118,7 @@ static void cisco_keepalive_send(struct net_device *dev, u32 type,
 	skb_put(skb, sizeof(struct cisco_packet));
 	skb->priority = TC_PRIO_CONTROL;
 	skb->dev = dev;
+	skb->protocol = htons(ETH_P_HDLC);
 	skb_reset_network_header(skb);
 
 	dev_queue_xmit(skb);
drivers/net/wan/hdlc_fr.c +3 -0
index 12b35404cd8e..d6cfd51613ed 100644
@@ -433,6 +433,8 @@ static netdev_tx_t pvc_xmit(struct sk_buff *skb, struct net_device *dev)
 			if (pvc->state.fecn) /* TX Congestion counter */
 				dev->stats.tx_compressed++;
 			skb->dev = pvc->frad;
+			skb->protocol = htons(ETH_P_HDLC);
+			skb_reset_network_header(skb);
 			dev_queue_xmit(skb);
 			return NETDEV_TX_OK;
 		}
@@ -555,6 +557,7 @@ static void fr_lmi_send(struct net_device *dev, int fullrep)
 	skb_put(skb, i);
 	skb->priority = TC_PRIO_CONTROL;
 	skb->dev = dev;
+	skb->protocol = htons(ETH_P_HDLC);
 	skb_reset_network_header(skb);
 
 	dev_queue_xmit(skb);
drivers/net/wan/hdlc_ppp.c +1 -0
index 16f33d1ffbfb..64f855651336 100644
@@ -251,6 +251,7 @@ static void ppp_tx_cp(struct net_device *dev, u16 pid, u8 code,
 
 	skb->priority = TC_PRIO_CONTROL;
 	skb->dev = dev;
+	skb->protocol = htons(ETH_P_HDLC);
 	skb_reset_network_header(skb);
 	skb_queue_tail(&tx_queue, skb);
 }
Signature · 1 line
2.25.1
maintainer Applied
#1 lore raw

From: Xie He <[email protected]>
Date: Wed, 16 Sep 2020 14:25:07 -0700

Quoted 39 lines

This patch sets skb->protocol before transmitting frames on the HDLC device, so that a user listening on the HDLC device with an AF_PACKET socket will see outgoing frames' sll_protocol field correctly set and consistent with that of incoming frames.

1. Control frames in hdlc_cisco and hdlc_ppp

When these drivers send control frames, skb->protocol is not set.

This value should be set to htons(ETH_P_HDLC), because when receiving control frames, their skb->protocol is set to htons(ETH_P_HDLC).

When receiving, hdlc_type_trans in hdlc.h is called, which then calls cisco_type_trans or ppp_type_trans. The skb->protocol of control frames is set to htons(ETH_P_HDLC) so that the control frames can be received by hdlc_rcv in hdlc.c, which calls cisco_rx or ppp_rx to process the control frames.

2. hdlc_fr

When this driver sends control frames, skb->protocol is set to internal values used in this driver.

When this driver sends data frames (from upper stacked PVC devices), skb->protocol is the same as that of the user data packet being sent on the upper PVC device (for normal PVC devices), or is htons(ETH_P_802_3) (for Ethernet-emulating PVC devices).

However, skb->protocol for both control frames and data frames should be set to htons(ETH_P_HDLC), because when receiving, all frames received on the HDLC device will have their skb->protocol set to htons(ETH_P_HDLC).

When receiving, hdlc_type_trans in hdlc.h is called, and because this driver doesn't provide a type_trans function in struct hdlc_proto, all frames will have their skb->protocol set to htons(ETH_P_HDLC). The frames are then received by hdlc_rcv in hdlc.c, which calls fr_rx to process the frames (control frames are consumed and data frames are re-received on upper PVC devices).

Quoted 2 lines
Cc Krzysztof Halasa <[email protected]>

Applied, thank you.