Skip to contentSkip to conversation

docs:dev-tools: Fix typo in Documentation/dev-tools

PATCH In review Masanari Iida 3 participants 3 messages Sep 17, 2020 – Sep 18, 2020

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 docs:dev-tools: Fix typo in Documentation/dev-tools

This patch fixes some spelling typos found in
Documentation/dev-tools.

---
 Documentation/dev-tools/kasan.rst    | 4 ++--
 Documentation/dev-tools/kcov.rst     | 2 +-
 Documentation/dev-tools/kmemleak.rst | 2 +-
 3 files changed, 4 insertions(+), 4 deletions(-)
Documentation/dev-tools/kasan.rst +2 -2
index c09c9ca2ff1c..49ec0ab6cfc7 100644
@@ -328,7 +328,7 @@ using something like insmod or modprobe. The module is called ``test_kasan``.
 ~~~~~~~~~~~~~
 
 With ``CONFIG_KUNIT`` built-in, ``CONFIG_KASAN_KUNIT_TEST`` can be built-in
-on any architecure that supports KASAN. These and any other KUnit
+on any architecture that supports KASAN. These and any other KUnit
 tests enabled will run and print the results at boot as a late-init
 call.
 
@@ -349,5 +349,5 @@ converted to KUnit. These tests can be run only as a module with
 ``CONFIG_KASAN`` built-in. The type of error expected and the
 function being run is printed before the expression expected to give
 an error. Then the error is printed, if found, and that test
-should be interpretted to pass only if the error was the one expected
+should be interpreted to pass only if the error was the one expected
 by the test.
Documentation/dev-tools/kcov.rst +1 -1
index 8548b0b04e43..d2c4c27e1702 100644
@@ -243,7 +243,7 @@ handles as they don't belong to a particular subsystem. The bytes 4-7 are
 currently reserved and must be zero. In the future the number of bytes
 used for the subsystem or handle ids might be increased.
 
-When a particular userspace proccess collects coverage via a common
+When a particular userspace process collects coverage via a common
 handle, kcov will collect coverage for each code section that is annotated
 to use the common handle obtained as kcov_handle from the current
 task_struct. However non common handles allow to collect coverage
Documentation/dev-tools/kmemleak.rst +1 -1
index a41a2d238af2..1c935f41cd3a 100644
@@ -229,7 +229,7 @@ Testing with kmemleak-test
 
 To check if you have all set up to use kmemleak, you can use the kmemleak-test
 module, a module that deliberately leaks memory. Set CONFIG_DEBUG_KMEMLEAK_TEST
-as module (it can't be used as bult-in) and boot the kernel with kmemleak
+as module (it can't be used as built-in) and boot the kernel with kmemleak
 enabled. Load the module and perform a scan with::
 
         # modprobe kmemleak-test
Signature · 1 line
2.28.0.497.g54e85e7af1ac
reviewer Acked-by on v1 1/1
#1 lore raw
Quoted 9 lines · Masanari Iida

This patch fixes some spelling typos found in
Documentation/dev-tools.

---
 Documentation/dev-tools/kasan.rst    | 4 ++--
 Documentation/dev-tools/kcov.rst     | 2 +-
 Documentation/dev-tools/kmemleak.rst | 2 +-
 3 files changed, 4 insertions(+), 4 deletions(-)

Thanks.

Signature · 1 line
~Randy
Reviewed-by on v1 1/1
#2 lore raw
In reply to Masanari Iida
Quoted 49 lines · Masanari Iida

This patch fixes some spelling typos found in
Documentation/dev-tools.

---
 Documentation/dev-tools/kasan.rst    | 4 ++--
 Documentation/dev-tools/kcov.rst     | 2 +-
 Documentation/dev-tools/kmemleak.rst | 2 +-
 3 files changed, 4 insertions(+), 4 deletions(-)
Documentation/dev-tools/kasan.rst +2 -2
index c09c9ca2ff1c..49ec0ab6cfc7 100644
@@ -328,7 +328,7 @@ using something like insmod or modprobe. The module is called ``test_kasan``.
 ~~~~~~~~~~~~~
 
 With ``CONFIG_KUNIT`` built-in, ``CONFIG_KASAN_KUNIT_TEST`` can be built-in
-on any architecure that supports KASAN. These and any other KUnit
+on any architecture that supports KASAN. These and any other KUnit
 tests enabled will run and print the results at boot as a late-init
 call.
 
@@ -349,5 +349,5 @@ converted to KUnit. These tests can be run only as a module with
 ``CONFIG_KASAN`` built-in. The type of error expected and the
 function being run is printed before the expression expected to give
 an error. Then the error is printed, if found, and that test
-should be interpretted to pass only if the error was the one expected
+should be interpreted to pass only if the error was the one expected
 by the test.
Documentation/dev-tools/kcov.rst +1 -1
index 8548b0b04e43..d2c4c27e1702 100644
@@ -243,7 +243,7 @@ handles as they don't belong to a particular subsystem. The bytes 4-7 are
 currently reserved and must be zero. In the future the number of bytes
 used for the subsystem or handle ids might be increased.
 
-When a particular userspace proccess collects coverage via a common
+When a particular userspace process collects coverage via a common
 handle, kcov will collect coverage for each code section that is annotated
 to use the common handle obtained as kcov_handle from the current
 task_struct. However non common handles allow to collect coverage
Documentation/dev-tools/kmemleak.rst +0 -0
index a41a2d238af2..1c935f41cd3a 100644

Documentation/dev-tools/kmemleak.rst Testing with kmemleak-test · line 235

Quoted 8 lines
Documentation/dev-tools/kmemleak.rst +1 -1
@@ -229,7 +229,7 @@ Testing with kmemleak-test
 
 To check if you have all set up to use kmemleak, you can use the kmemleak-test
 module, a module that deliberately leaks memory. Set CONFIG_DEBUG_KMEMLEAK_TEST
-as module (it can't be used as bult-in) and boot the kernel with kmemleak
+as module (it can't be used as built-in) and boot the kernel with kmemleak
 enabled. Load the module and perform a scan with::
 
         # modprobe kmemleak-test