Skip to contentSkip to conversation

arm64: dts: ti: k3-j7200: add dma and mcu cpsw

PATCH Superseded Grygorii Strashko 2 participants 7 messages Sep 18, 2020

Subsystems (2)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

v3 cover arm64: dts: ti: k3-j7200: add dma and mcu cpsw

Hi All,

This series adds DT nodes for TI J7200 SoC
- Ringacc and UDMA nodes for Main and MCU NAVSS, which are compatible with J721E Soc, to enable DMA support
- MCU CPSW2g DT nodes to enable networking and board data

This series depends on:
- [PATCH v4 0/5] arm64: Initial support for Texas Instrument's J7200 Platform [1]
from: Lokesh Vutla <[email protected]>

[1] https://patchwork.kernel.org/cover/11774429/

Changes in v3:
- rebase on top of [1]
- updated dependencies
- added tested-by

Changes in v2:
- fixed DT build warnings (Nishanth Menon)

v1: https://lore.kernel.org/patchwork/cover/1301067/

Grygorii Strashko (3):
arm64: dts: ti: k3-j7200-main: add main navss cpts node
arm64: dts: ti: k3-j7200-mcu: add mcu cpsw nuss node
arm64: dts: ti: k3-j7200-common-proc-board: add mcu cpsw nuss pinmux and phy defs

Peter Ujfalusi (1):
arm64: dts: ti: k3-j7200: add DMA support

 .../dts/ti/k3-j7200-common-proc-board.dts     |  45 +++++++
 arch/arm64/boot/dts/ti/k3-j7200-main.dtsi     |  48 +++++++
 .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi      | 118 ++++++++++++++++++
 3 files changed, 211 insertions(+)
Signature · 7 lines
2.17.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#1 lore raw

PATCH v3 1/4 arm64: dts: ti: k3-j7200: add DMA support

From: Peter Ujfalusi <[email protected]>

Add the intr, inta, ringacc and udmap nodes for main and mcu NAVSS.

---
 arch/arm64/boot/dts/ti/k3-j7200-main.dtsi     | 36 +++++++++++++++
 .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi      | 44 +++++++++++++++++++
 2 files changed, 80 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +36 -0
index 3df49577b06a..c5015df58cd4 100644
@@ -93,6 +93,42 @@
 			interrupt-names = "rx_011";
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 		};
+
+		main_ringacc: ringacc@3c000000 {
+			compatible = "ti,am654-navss-ringacc";
+			reg =	<0x0 0x3c000000 0x0 0x400000>,
+				<0x0 0x38000000 0x0 0x400000>,
+				<0x0 0x31120000 0x0 0x100>,
+				<0x0 0x33000000 0x0 0x40000>;
+			reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target";
+			ti,num-rings = <1024>;
+			ti,sci-rm-range-gp-rings = <0x1>; /* GP ring range */
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <211>;
+			msi-parent = <&main_udmass_inta>;
+		};
+
+		main_udmap: dma-controller@31150000 {
+			compatible = "ti,j721e-navss-main-udmap";
+			reg =	<0x0 0x31150000 0x0 0x100>,
+				<0x0 0x34000000 0x0 0x100000>,
+				<0x0 0x35000000 0x0 0x100000>;
+			reg-names = "gcfg", "rchanrt", "tchanrt";
+			msi-parent = <&main_udmass_inta>;
+			#dma-cells = <1>;
+
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <212>;
+			ti,ringacc = <&main_ringacc>;
+
+			ti,sci-rm-range-tchan = <0x0d>, /* TX_CHAN */
+						<0x0f>, /* TX_HCHAN */
+						<0x10>; /* TX_UHCHAN */
+			ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */
+						<0x0b>, /* RX_HCHAN */
+						<0x0c>; /* RX_UHCHAN */
+			ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
+		};
 	};
 
 	main_pmx0: pinctrl@11c000 {
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +44 -0

48 lines not on this page · raw message

Signature · 7 lines
2.17.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#2 lore raw

Re: [PATCH v3 1/4] arm64: dts: ti: k3-j7200: add DMA support

Hi Grygorii,

Quoted 3 lines · Grygorii Strashko

From: Peter Ujfalusi <[email protected]>

Add the intr, inta, ringacc and udmap nodes for main and mcu NAVSS.

Need to update the changelog, intr and inta are not part of this revised series.

Quoted 70 lines
---
 arch/arm64/boot/dts/ti/k3-j7200-main.dtsi     | 36 +++++++++++++++
 .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi      | 44 +++++++++++++++++++
 2 files changed, 80 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +36 -0
index 3df49577b06a..c5015df58cd4 100644
@@ -93,6 +93,42 @@
 			interrupt-names = "rx_011";
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 		};
+
+		main_ringacc: ringacc@3c000000 {
+			compatible = "ti,am654-navss-ringacc";
+			reg =	<0x0 0x3c000000 0x0 0x400000>,
+				<0x0 0x38000000 0x0 0x400000>,
+				<0x0 0x31120000 0x0 0x100>,
+				<0x0 0x33000000 0x0 0x40000>;
+			reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target";
+			ti,num-rings = <1024>;
+			ti,sci-rm-range-gp-rings = <0x1>; /* GP ring range */
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <211>;
+			msi-parent = <&main_udmass_inta>;
+		};
+
+		main_udmap: dma-controller@31150000 {
+			compatible = "ti,j721e-navss-main-udmap";
+			reg =	<0x0 0x31150000 0x0 0x100>,
+				<0x0 0x34000000 0x0 0x100000>,
+				<0x0 0x35000000 0x0 0x100000>;
+			reg-names = "gcfg", "rchanrt", "tchanrt";
+			msi-parent = <&main_udmass_inta>;
+			#dma-cells = <1>;
+
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <212>;
+			ti,ringacc = <&main_ringacc>;
+
+			ti,sci-rm-range-tchan = <0x0d>, /* TX_CHAN */
+						<0x0f>, /* TX_HCHAN */
+						<0x10>; /* TX_UHCHAN */
+			ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */
+						<0x0b>, /* RX_HCHAN */
+						<0x0c>; /* RX_UHCHAN */
+			ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
+		};
 	};
 
 	main_pmx0: pinctrl@11c000 {
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +6 -0
index ec2745e0768e..7ecdfdb46436 100644
@@ -92,4 +92,48 @@
 		ti,sci-dev-id = <137>;
 		ti,interrupt-ranges = <16 960 16>;
 	};
+
+	cbass_mcu_navss: navss@28380000 {
+		compatible = "simple-mfd";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;

arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi line 110

Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +10 -0
+		dma-coherent;
+		dma-ranges;
+		ti,sci-dev-id = <232>;
+
+		mcu_ringacc: ringacc@2b800000 {
+			compatible = "ti,am654-navss-ringacc";
+			reg =	<0x0 0x2b800000 0x0 0x400000>,
+				<0x0 0x2b000000 0x0 0x400000>,
+				<0x0 0x28590000 0x0 0x100>,
+				<0x0 0x2a500000 0x0 0x40000>;

Please use style consistent with existing dts nodes, not a fan of mismatched usage. We are using 0x00 for the higher 32-bit addresses and sizes. Comment applies to all the nodes and all patches in the series.

regards
Suman

Quoted 20 lines
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +19 -0
+			reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target";
+			ti,num-rings = <286>;
+			ti,sci-rm-range-gp-rings = <0x1>; /* GP ring range */
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <235>;
+			msi-parent = <&main_udmass_inta>;
+		};
+
+		mcu_udmap: dma-controller@285c0000 {
+			compatible = "ti,j721e-navss-mcu-udmap";
+			reg =	<0x0 0x285c0000 0x0 0x100>,
+				<0x0 0x2a800000 0x0 0x40000>,
+				<0x0 0x2aa00000 0x0 0x40000>;
+			reg-names = "gcfg", "rchanrt", "tchanrt";
+			msi-parent = <&main_udmass_inta>;
+			#dma-cells = <1>;
+
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <236>;

arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi line 139

Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +9 -0
+			ti,ringacc = <&mcu_ringacc>;
+
+			ti,sci-rm-range-tchan = <0x0d>, /* TX_CHAN */
+						<0x0f>; /* TX_HCHAN */
+			ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */
+						<0x0b>; /* RX_HCHAN */
+			ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
+		};
+	};
 };

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#3 lore raw

PATCH v3 2/4 arm64: dts: ti: k3-j7200-main: add main navss cpts node

In reply to Grygorii Strashko

Add DT node for Main NAVSS CPTS module.

---
 arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +12 -0
index c5015df58cd4..31bd0c5ffb8b 100644
@@ -129,6 +129,18 @@
 						<0x0c>; /* RX_UHCHAN */
 			ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
 		};
+
+		cpts@310d0000 {
+			compatible = "ti,j721e-cpts";
+			reg = <0x0 0x310d0000 0x0 0x400>;
+			reg-names = "cpts";
+			clocks = <&k3_clks 201 1>;
+			clock-names = "cpts";
+			interrupts-extended = <&main_navss_intr 391>;
+			interrupt-names = "cpts";
+			ti,cpts-periodic-outputs = <6>;
+			ti,cpts-ext-ts-inputs = <8>;
+		};
 	};
 
 	main_pmx0: pinctrl@11c000 {
Signature · 7 lines
2.17.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#4 lore raw

PATCH v3 3/4 arm64: dts: ti: k3-j7200-mcu: add mcu cpsw nuss node

In reply to Grygorii Strashko

Add DT node for The TI j7200 MCU SoC Gigabit Ethernet two ports Switch subsystem (MCU CPSW NUSS).

---
 .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi      | 74 +++++++++++++++++++
 1 file changed, 74 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +74 -0
index 7ecdfdb46436..a994276a8b3d 100644
@@ -34,6 +34,20 @@
 		};
 	};
 
+	mcu_conf: syscon@40f00000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x0 0x40f00000 0x0 0x20000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x40f00000 0x20000>;
+
+		phy_gmii_sel: phy@4040 {
+			compatible = "ti,am654-phy-gmii-sel";
+			reg = <0x4040 0x4>;
+			#phy-cells = <1>;
+		};
+	};
+
 	chipid@43000014 {
 		compatible = "ti,am654-chipid";
 		reg = <0x00 0x43000014 0x00 0x4>;
@@ -136,4 +150,64 @@
 			ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
 		};
 	};
+
+	mcu_cpsw: ethernet@46000000 {
+		compatible = "ti,j721e-cpsw-nuss";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		reg = <0x0 0x46000000 0x0 0x200000>;
+		reg-names = "cpsw_nuss";
+		ranges = <0x0 0x0 0x0 0x46000000 0x0 0x200000>;
+		dma-coherent;
+		clocks = <&k3_clks 18 21>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 18 TI_SCI_PD_EXCLUSIVE>;
+
+		dmas = <&mcu_udmap 0xf000>,
+		       <&mcu_udmap 0xf001>,
+		       <&mcu_udmap 0xf002>,
+		       <&mcu_udmap 0xf003>,
+		       <&mcu_udmap 0xf004>,
+		       <&mcu_udmap 0xf005>,
+		       <&mcu_udmap 0xf006>,
+		       <&mcu_udmap 0xf007>,
+		       <&mcu_udmap 0x7000>;
+		dma-names = "tx0", "tx1", "tx2", "tx3",
+			    "tx4", "tx5", "tx6", "tx7",
+			    "rx";
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cpsw_port1: port@1 {
+				reg = <1>;
+				ti,mac-only;
+				label = "port1";
+				ti,syscon-efuse = <&mcu_conf 0x200>;
+				phys = <&phy_gmii_sel 1>;
+			};
+		};
+
+		davinci_mdio: mdio@f00 {
+			compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+			reg = <0x0 0xf00 0x0 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&k3_clks 18 21>;
+			clock-names = "fck";
+			bus_freq = <1000000>;
+		};
+
+		cpts@3d000 {
+			compatible = "ti,am65-cpts";
+			reg = <0x0 0x3d000 0x0 0x400>;
+			clocks = <&k3_clks 18 2>;
+			clock-names = "cpts";
+			interrupts-extended = <&gic500 GIC_SPI 858 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "cpts";
+			ti,cpts-ext-ts-inputs = <4>;
+			ti,cpts-periodic-outputs = <2>;
+		};
+	};
 };
Signature · 1 line
2.17.1
#5 lore raw

Re: [PATCH v3 3/4] arm64: dts: ti: k3-j7200-mcu: add mcu cpsw nuss node

Quoted 2 lines · Grygorii Strashko

Add DT node for The TI j7200 MCU SoC Gigabit Ethernet two ports Switch subsystem (MCU CPSW NUSS).

nit, %s/j7200/J7200/ on this patch and the next.

regards
Suman

Quoted 98 lines
---
 .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi      | 74 +++++++++++++++++++
 1 file changed, 74 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +74 -0
index 7ecdfdb46436..a994276a8b3d 100644
@@ -34,6 +34,20 @@
 		};
 	};
 
+	mcu_conf: syscon@40f00000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x0 0x40f00000 0x0 0x20000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x40f00000 0x20000>;
+
+		phy_gmii_sel: phy@4040 {
+			compatible = "ti,am654-phy-gmii-sel";
+			reg = <0x4040 0x4>;
+			#phy-cells = <1>;
+		};
+	};
+
 	chipid@43000014 {
 		compatible = "ti,am654-chipid";
 		reg = <0x00 0x43000014 0x00 0x4>;
@@ -136,4 +150,64 @@
 			ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
 		};
 	};
+
+	mcu_cpsw: ethernet@46000000 {
+		compatible = "ti,j721e-cpsw-nuss";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		reg = <0x0 0x46000000 0x0 0x200000>;
+		reg-names = "cpsw_nuss";
+		ranges = <0x0 0x0 0x0 0x46000000 0x0 0x200000>;
+		dma-coherent;
+		clocks = <&k3_clks 18 21>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 18 TI_SCI_PD_EXCLUSIVE>;
+
+		dmas = <&mcu_udmap 0xf000>,
+		       <&mcu_udmap 0xf001>,
+		       <&mcu_udmap 0xf002>,
+		       <&mcu_udmap 0xf003>,
+		       <&mcu_udmap 0xf004>,
+		       <&mcu_udmap 0xf005>,
+		       <&mcu_udmap 0xf006>,
+		       <&mcu_udmap 0xf007>,
+		       <&mcu_udmap 0x7000>;
+		dma-names = "tx0", "tx1", "tx2", "tx3",
+			    "tx4", "tx5", "tx6", "tx7",
+			    "rx";
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cpsw_port1: port@1 {
+				reg = <1>;
+				ti,mac-only;
+				label = "port1";
+				ti,syscon-efuse = <&mcu_conf 0x200>;
+				phys = <&phy_gmii_sel 1>;
+			};
+		};
+
+		davinci_mdio: mdio@f00 {
+			compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+			reg = <0x0 0xf00 0x0 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&k3_clks 18 21>;
+			clock-names = "fck";
+			bus_freq = <1000000>;
+		};
+
+		cpts@3d000 {
+			compatible = "ti,am65-cpts";
+			reg = <0x0 0x3d000 0x0 0x400>;
+			clocks = <&k3_clks 18 2>;
+			clock-names = "cpts";
+			interrupts-extended = <&gic500 GIC_SPI 858 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "cpts";
+			ti,cpts-ext-ts-inputs = <4>;
+			ti,cpts-periodic-outputs = <2>;
+		};
+	};
 };
#6 lore raw

PATCH v3 4/4 arm64: dts: ti: k3-j7200-common-proc-board: add mcu cpsw nuss pinmux and phy defs

In reply to Grygorii Strashko

The TI j7200 EVM base board has TI DP83867 PHY connected to external CPSW NUSS Port 1 in rgmii-rxid mode.

Hence, add pinmux and Ethernet PHY configuration for TI j7200 SoC MCU Gigabit Ethernet two ports Switch subsystem (CPSW NUSS).

---
 .../dts/ti/k3-j7200-common-proc-board.dts     | 45 +++++++++++++++++++
 1 file changed, 45 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +45 -0
index e27069317c4e..f7e6b9b5ef5f 100644
@@ -6,6 +6,7 @@
 /dts-v1/;
 
 #include "k3-j7200-som-p0.dtsi"
+#include <dt-bindings/net/ti-dp83867.h>
 
 / {
 	chosen {
@@ -14,6 +15,32 @@
 	};
 };
 
+&wkup_pmx0 {
+	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
+			J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
+			J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
+			J721E_WKUP_IOPAD(0x0074, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
+			J721E_WKUP_IOPAD(0x0078, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
+			J721E_WKUP_IOPAD(0x007c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
+			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
+			J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
+			J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
+			J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
+			J721E_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* MCU_RGMII1_TXC */
+			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
+		>;
+	};
+
+	mcu_mdio_pins_default: mcu-mdio1-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
+			J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
+		>;
+	};
+};
+
 &wkup_uart0 {
 	/* Wakeup UART is used by System firmware */
 	status = "disabled";
@@ -62,3 +89,21 @@
 	/* UART not brought out */
 	status = "disabled";
 };
+
+&mcu_cpsw {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
+};
+
+&davinci_mdio {
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+	};
+};
+
+&cpsw_port1 {
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&phy0>;
+};
Signature · 1 line
2.17.1