ath10k: Introduce download cal from mtd
Subsystems (6)
PATCH 1/1 ath10k: Introduce download cal from mtd
Most of routers that have the ath10k wifi chip integrated in the Soc have the pre-cal data stored in the art (or equivalent) mtd partition. Introduce a new function to directly extract and use it based on what is set in the dt if the system have mtd support.
Pre-cal file have still priority to everything else.
Tested-on: QCA9984 hw1.0 PCI 10.4
--- drivers/net/wireless/ath/ath10k/core.c | 74 ++++++++++++++++++++++++++ drivers/net/wireless/ath/ath10k/core.h | 3 ++ 2 files changed, 77 insertions(+)
drivers/net/wireless/ath/ath10k/core.c +74 -0
@@ -13,6 +13,7 @@#include <linux/ctype.h> #include <linux/pm_qos.h> #include <asm/byteorder.h> +#include <linux/mtd/mtd.h> #include "core.h" #include "mac.h"
@@ -1701,6 +1702,69 @@ static int ath10k_download_and_run_otp(struct ath10k *ar)return 0 ; } +static int ath10k_download_cal_mtd (struct ath10k *ar) +{ +#ifdef CONFIG_MTD +struct device_node *node, *mtd_node =NULL ; +struct mtd_info *mtd; +const __be32 *list; +u32 offset, size; +const char *part; +phandle phandle; +size_t retlen; +char *file; +int ret; + + node = ar->dev->of_node; +if (!node) +return -ENOENT ; + + list =of_get_property (node,"qcom,ath10k-pre-calibration-data-mtd" , &size); +if (!list || (size != (3 *sizeof (*list)))) +return -EINVAL ; + + phandle =be32_to_cpup (list++); +if (phandle) + mtd_node =of_find_node_by_phandle (phandle); + +if (!mtd_node) +return -ENODEV ; + + part =of_get_property (mtd_node,"label" ,NULL ); +if (!part) + part = mtd_node->name; + + mtd =get_mtd_device_nm (part); +if (IS_ERR (mtd)) +return -ENODEV ; + + offset =be32_to_cpup (list++); + size =be32_to_cpup (list); + + file =kzalloc (size,GFP_KERNEL ); +if (!file) +return -ENOMEM ; + + ret =mtd_read (mtd, offset, size, &retlen, file); +put_mtd_device (mtd); + + ret =ath10k_download_board_data (ar, file, size); +if (ret) { +ath10k_err (ar,"failed to download cal_file data: %d\n" , ret); + goto err; + } + +ath10k_dbg (ar,ATH10K_DBG_BOOT ,"boot cal file downloaded\n" ); + +return 0 ; + +err: +kfree (file); +return ret; +#endif +return -EOPNOTSUPP ; +} +static int ath10k_download_cal_file (struct ath10k *ar,const struct firmware *file) {
@@ -2047,6 +2111,16 @@ static int ath10k_core_pre_cal_download(struct ath10k *ar) goto success; } +ath10k_dbg (ar,ATH10K_DBG_BOOT , +"boot did not find a pre calibration file, try MTD next: %d\n" , + ret); + + ret =ath10k_download_cal_mtd (ar); +if (ret ==0 ) { + ar->cal_mode =ATH10K_PRE_CAL_MODE_MTD ; + goto success; + } +ath10k_dbg (ar,ATH10K_DBG_BOOT ,"boot did not find a pre calibration file, try DT next: %d\n" , ret);
drivers/net/wireless/ath/ath10k/core.h +3 -0
@@ -864,6 +864,7 @@ enum ath10k_cal_mode {ATH10K_CAL_MODE_OTP ,ATH10K_CAL_MODE_DT ,ATH10K_PRE_CAL_MODE_FILE , +ATH10K_PRE_CAL_MODE_MTD ,ATH10K_PRE_CAL_MODE_DT , ATH10K_CAL_MODE_EEPROM, };
@@ -886,6 +887,8 @@ static inline const char *ath10k_cal_mode_str(enum ath10k_cal_mode mode)return "dt" ;case ATH10K_PRE_CAL_MODE_FILE :return "pre-cal-file" ; +case ATH10K_PRE_CAL_MODE_MTD : +return "pre-cal-mtd" ;case ATH10K_PRE_CAL_MODE_DT :return "pre-cal-dt" ;case ATH10K_CAL_MODE_EEPROM :
Signature · 7 lines
2.27.0 _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k
PATCH 2/2 dt: bindings: ath10k: Document qcom,ath10k-pre-calibration-data-mtd
Document use of qcom,ath10k-pre-calibration-data-mtd bindings used to define from where the driver will load the pre-cal data in the defined mtd partition.
--- .../devicetree/bindings/net/wireless/qcom,ath10k.txt | 12 +++++++++--- 1 file changed, 9 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +9 -3
@@ -15,9 +15,9 @@ and also uses most of the properties defined in this doc (except "qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data" to carry pre calibration data. -In general, entry "qcom,ath10k-pre-calibration-data" and -"qcom,ath10k-calibration-data" conflict with each other and only one -can be provided per device. +In general, entry "qcom,ath10k-pre-calibration-data", +"qcom,ath10k-calibration-data-mtd" and "qcom,ath10k-calibration-data" conflict with +each other and only one can be provided per device. SNOC based devices (i.e. wcn3990) uses compatible string "qcom,wcn3990-wifi".
@@ -63,6 +63,12 @@ Optional properties: hw versions. - qcom,ath10k-pre-calibration-data : pre calibration data as an array, the length can vary between hw versions. +- qcom,ath10k-pre-calibration-data-mtd : + Usage: optional + Value type: <phandle offset size> + Definition: pre calibration data read from mtd partition. Take 3 value, the + mtd to read data from, the offset in the mtd partition and the + size of data to read. - <supply-name>-supply: handle to the regulator device tree node optional "supply-name" are "vdd-0.8-cx-mx", "vdd-1.8-xo", "vdd-1.3-rfa", "vdd-3.3-ch0",
Signature · 7 lines
2.27.0 _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k
Re: [PATCH 2/2] dt: bindings: ath10k: Document qcom, ath10k-pre-calibration-data-mtd
Quoted 5 lines · Ansuel Smith
Document use of qcom,ath10k-pre-calibration-data-mtd bindings used to define from where the driver will load the pre-cal data in the defined mtd partition.
Signed-off-by Ansuel Smith <[email protected]>
Q: Doesn't mtd now come with nvmem support from the get go? So the MAC-Addresses and pre-caldata could be specified as a nvmem-node in the devicetree? I remember seeing that this was worked on or was this mtd->nvmem dropped?
Cheers,
Christian
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
R: [PATCH 2/2] dt: bindings: ath10k: Document qcom, ath10k-pre-calibration-data-mtd
Quoted 24 lines
-----Messaggio originale-----
Da: Christian Lamparter <[email protected]>
Inviato: venerdì 18 settembre 2020 18:54
A: Ansuel Smith <[email protected]>; Kalle Valo <[email protected]>
Cc: [email protected]; [email protected]; linux- [email protected]; [email protected]; [email protected]; David S. Miller <[email protected]>; Rob Herring <[email protected]>; Jakub Kicinski <[email protected]>; linux- [email protected]; Srinivas Kandagatla <[email protected]>; Bartosz Golaszewski <[email protected]>
Oggetto: Re: [PATCH 2/2] dt: bindings: ath10k: Document qcom, ath10k- pre-calibration-data-mtdQuoted 5 lines · Ansuel Smith
Document use of qcom,ath10k-pre-calibration-data-mtd bindings used to define from where the driver will load the pre-cal data in the defined mtd partition.
Signed-off-by Ansuel Smith <[email protected]>
Quoted 7 lines
Q: Doesn't mtd now come with nvmem support from the get go? So the MAC-Addresses and pre-caldata could be specified as a nvmem-node in the devicetree? I remember seeing that this was worked on or was this
mtd->nvmemdropped?Cheers,
Christian
Can you give me some example where this is used? I can't find any reference.
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
R: [PATCH 2/2] dt: bindings: ath10k: Document qcom, ath10k-pre-calibration-data-mtd
In reply to Christian LamparterQuoted 24 lines
-----Messaggio originale-----
Da: Christian Lamparter <[email protected]>
Inviato: venerdì 18 settembre 2020 18:54
A: Ansuel Smith <[email protected]>; Kalle Valo <[email protected]>
Cc: [email protected]; [email protected]; linux- [email protected]; [email protected]; [email protected]; David S. Miller <[email protected]>; Rob Herring <[email protected]>; Jakub Kicinski <[email protected]>; linux- [email protected]; Srinivas Kandagatla <[email protected]>; Bartosz Golaszewski <[email protected]>
Oggetto: Re: [PATCH 2/2] dt: bindings: ath10k: Document qcom, ath10k- pre-calibration-data-mtdQuoted 5 lines · Ansuel Smith
Document use of qcom,ath10k-pre-calibration-data-mtd bindings used to define from where the driver will load the pre-cal data in the defined mtd partition.
Signed-off-by Ansuel Smith <[email protected]>
Quoted 7 lines
Q: Doesn't mtd now come with nvmem support from the get go? So the MAC-Addresses and pre-caldata could be specified as a nvmem-node in the devicetree? I remember seeing that this was worked on or was this
mtd->nvmemdropped?Cheers,
Christian
Sorry a lot for the double email... I think I found what you are talking about. It looks like the code was merged but not the documentation.
Will do some test and check if this works.
This should be the related patch.
https://patchwork.ozlabs.org/project/linux-mtd/patch/[email protected]/
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Re: R: [PATCH 2/2] dt: bindings: ath10k: Document qcom, ath10k-pre-calibration-data-mtd
Quoted 32 lines · On 2020-09-18 20:31, [email protected] wrote:
Quoted 24 lines
-----Messaggio originale-----
Da: Christian Lamparter <[email protected]>
Inviato: venerdì 18 settembre 2020 18:54
A: Ansuel Smith <[email protected]>; Kalle Valo <[email protected]>
Cc: [email protected]; [email protected]; linux- [email protected]; [email protected]; [email protected]; David S. Miller <[email protected]>; Rob Herring <[email protected]>; Jakub Kicinski <[email protected]>; linux- [email protected]; Srinivas Kandagatla <[email protected]>; Bartosz Golaszewski <[email protected]>
Oggetto: Re: [PATCH 2/2] dt: bindings: ath10k: Document qcom, ath10k- pre-calibration-data-mtdQuoted 5 lines · Ansuel Smith
Document use of qcom,ath10k-pre-calibration-data-mtd bindings used to define from where the driver will load the pre-cal data in the defined mtd partition.
Signed-off-by Ansuel Smith <[email protected]>Quoted 7 lines
Q: Doesn't mtd now come with nvmem support from the get go? So the MAC-Addresses and pre-caldata could be specified as a nvmem-node in the devicetree? I remember seeing that this was worked on or was this
mtd->nvmemdropped?Cheers,
Christian
Quoted 7 lines
Sorry a lot for the double email... I think I found what you are talking about. It looks like the code was merged but not the documentation.
Will do some test and check if this works.This should be the related patch.
https://patchwork.ozlabs.org/project/linux-mtd/patch/[email protected]/
Well, I guess the version that was merged:
|commit c4dfa25ab307a277eafa7067cd927fbe4d9be4ba |Author: Alban Bedel <[email protected]> |Date: Tue Nov 13 15:01:10 2018 +0100 | | mtd: add support for reading MTD devices via the nvmem API | | Allow drivers that use the nvmem API to read data stored on MTD devices. | For this the mtd devices are registered as read-only NVMEM providers. | | >>>We don't support device tree systems for now.<<<
answers this. Sorry for the noise. Yee, this likely isn't going to work as it is still disabled on purpose.
Regards,
Christian
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k