net: stmmac: Enable VLAN filter fail queue for Intel platform data
Subsystems (4)
cover net: stmmac: Enable VLAN filter fail queue for Intel platform data
This is a follow-up on a earlier patch submission at:-
https://patchwork.ozlabs.org/patch/1275604/
Changes since the previous patch submission:
- Enable VLAN fail queue for Intel platform data (dwmac-intel).
- Steer the VLAN failed packet to the last Rx queue.
Chuah, Kim Tatt (1):
net: stmmac: Add option for VLAN filter fail queue enable
drivers/net/ethernet/stmicro/stmmac/common.h | 2 ++ drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c | 5 +++++ drivers/net/ethernet/stmicro/stmmac/dwmac4.h | 1 + drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c | 15 +++++++++++++-- drivers/net/ethernet/stmicro/stmmac/dwmac5.h | 6 ++++++ drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 3 +++ include/linux/stmmac.h | 2 ++ 7 files changed, 32 insertions(+), 2 deletions(-)
Signature · 1 line
2.17.0
PATCH 1/1 net: stmmac: Add option for VLAN filter fail queue enable
From: "Chuah, Kim Tatt" <[email protected]>
Add option in plat_stmmacenet_data struct to enable VLAN Filter Fail Queuing. This option allows packets that fail VLAN filter to be routed to a specific Rx queue when Receive All is also set.
When this option is enabled:
- Enable VFFQ only when entering promiscuous mode, because Receive All will pass up all rx packets that failed address filtering (similar to promiscuous mode).
- VLAN-promiscuous mode is never entered to allow rx packet to fail VLAN filters and get routed to selected VFFQ Rx queue.
--- drivers/net/ethernet/stmicro/stmmac/common.h | 2 ++ drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c | 5 +++++ drivers/net/ethernet/stmicro/stmmac/dwmac4.h | 1 + drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c | 15 +++++++++++++-- drivers/net/ethernet/stmicro/stmmac/dwmac5.h | 6 ++++++ drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 3 +++ include/linux/stmmac.h | 2 ++ 7 files changed, 32 insertions(+), 2 deletions(-)
drivers/net/ethernet/stmicro/stmmac/common.h +2 -0
@@ -481,6 +481,8 @@ struct mac_device_info {unsigned int num_vlan;u32 vlan_filter[32 ];unsigned int promisc; +bool vlan_fail_q_en; +u8 vlan_fail_q; };struct stmmac_rx_routing {
drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c +5 -0
@@ -321,6 +321,11 @@ static int intel_mgbe_common_data(struct pci_dev *pdev,/* Set the maxmtu to a default of JUMBO_LEN */ plat->maxmtu =JUMBO_LEN ; + plat->vlan_fail_q_en = true; + +/* Use the last Rx queue */ + plat->vlan_fail_q = plat->rx_queues_to_use -1 ; +return 0 ; }
drivers/net/ethernet/stmicro/stmmac/dwmac4.h +1 -0
@@ -76,6 +76,7 @@#define GMAC_PACKET_FILTER_HPF BIT(10)#define GMAC_PACKET_FILTER_VTFE BIT(16)#define GMAC_PACKET_FILTER_IPFE BIT(20) +#define GMAC_PACKET_FILTER_RA BIT(31)#define GMAC_MAX_PERFECT_ADDRESSES 128
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c +13 -2
@@ -618,7 +618,18 @@ static void dwmac4_set_filter(struct mac_device_info *hw, value &= ~GMAC_PACKET_FILTER_PM ; value &= ~GMAC_PACKET_FILTER_PR ;if (dev->flags &IFF_PROMISC ) { - value =GMAC_PACKET_FILTER_PR |GMAC_PACKET_FILTER_PCF ; +/* VLAN Tag Filter Fail Packets Queuing */ +if (hw->vlan_fail_q_en) { + value =readl (ioaddr +GMAC_RXQ_CTRL4 ); + value &= ~GMAC_RXQCTRL_VFFQ_MASK ; + value |=GMAC_RXQCTRL_VFFQE | + (hw->vlan_fail_q <<GMAC_RXQCTRL_VFFQ_SHIFT ); +writel (value, ioaddr +GMAC_RXQ_CTRL4 ); + value =GMAC_PACKET_FILTER_PR |GMAC_PACKET_FILTER_RA ; + }else { + value =GMAC_PACKET_FILTER_PR |GMAC_PACKET_FILTER_PCF ; + } + }else if ((dev->flags &IFF_ALLMULTI ) || (netdev_mc_count (dev) > hw->multicast_filter_bins)) {/* Pass all multi */
@@ -680,7 +691,7 @@ static void dwmac4_set_filter(struct mac_device_info *hw,writel (value, ioaddr +GMAC_PACKET_FILTER ); -if (dev->flags &IFF_PROMISC ) { +if (dev->flags &IFF_PROMISC && !hw->vlan_fail_q_en) {if (!hw->promisc) { hw->promisc =1 ;dwmac4_vlan_promisc_enable (dev, hw);
drivers/net/ethernet/stmicro/stmmac/dwmac5.h +6 -0
@@ -92,6 +92,12 @@#define TCEIE BIT(0)#define DMA_ECC_INT_STATUS 0x00001088 +/* EQoS version 5.xx VLAN Tag Filter Fail Packets Queuing */ +#define GMAC_RXQ_CTRL4 0x00000094 +#define GMAC_RXQCTRL_VFFQ_MASK GENMASK(19, 17) +#define GMAC_RXQCTRL_VFFQ_SHIFT 17 +#define GMAC_RXQCTRL_VFFQE BIT(16) +int dwmac5_safety_feat_config (void __iomem *ioaddr,unsigned int asp); int dwmac5_safety_feat_irq_status(struct net_device *ndev, void __iomem *ioaddr, unsigned int asp,
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +3 -0
@@ -4709,6 +4709,9 @@ static int stmmac_hw_init(struct stmmac_priv *priv)if (priv->dma_cap.tsoen)dev_info (priv->device,"TSO supported\n" ); + priv->hw->vlan_fail_q_en = priv->plat->vlan_fail_q_en; + priv->hw->vlan_fail_q = priv->plat->vlan_fail_q; +/* Run HW quirks, if any */ if (priv->hwif_quirks) { ret = priv->hwif_quirks (priv);
include/linux/stmmac.h +2 -0
@@ -198,5 +198,7 @@ struct plat_stmmacenet_data {int mac_port_sel_speed;bool en_tx_lpi_clockgating;int has_xgmac; +bool vlan_fail_q_en; + u8 vlan_fail_q; };#endif
Signature · 7 lines
2.17.0 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH net-next 1/1] net: stmmac: Add option for VLAN filter fail queue enable
From: Wong Vee Khee <[email protected]>
Date: Fri, 25 Sep 2020 17:40:41 +0800
Quoted 13 lines
From: "Chuah, Kim Tatt" <[email protected]>
Add option in
plat_stmmacenet_datastruct to enable VLAN Filter Fail Queuing. This option allows packets that fail VLAN filter to be routed to a specific Rx queue when Receive All is also set.When this option is enabled:
- Enable VFFQ only when entering promiscuous mode, because Receive All will pass up all rx packets that failed address filtering (similar to promiscuous mode).
- VLAN-promiscuous mode is never entered to allow rx packet to fail VLAN filters and get routed to selected VFFQ Rx queue.
Quoted 4 lines
Reviewed-by Voon Weifeng <[email protected]>Reviewed-by Ong Boon Leong <[email protected]>Signed-off-by Chuah, Kim Tatt <[email protected]>Signed-off-by Ong Boon Leong <[email protected]>
Applied.