Add SDM630/636/660 interconnect driver
Subsystems (3)
v2 cover Add SDM630/636/660 interconnect driver
From: AngeloGioacchino Del Regno <[email protected]>
This patch series adds the SDM660 interconnect provider driver in order to stop some timeouts and achieve some decent performance by avoiding to be NoC limited.
It's also providing some power consumption improvement, but I have only measured that as less heat, which is quite important when working on thermally constrained devices like smartphones.
Please note that this driver's yaml binding is referring to a MMCC clock, so this series does depend on the SDM660 MMCC driver that I have sent separately.
The multimedia clock is required only for the Multimedia NoC (mnoc).
This patch series has been tested against the following devices:
- Sony Xperia XA2 Ultra (SDM630 Nile Discovery)
- Sony Xperia 10 (SDM630 Ganges Kirin)
- Sony Xperia 10 Plus (SDM636 Ganges Mermaid)
Changes in v2:
- Added missing qcom,mmcc-sdm660.h dt-binding include in the interconnect/qcom,sdm660.yaml binding, as pointed out by Rob Herring
AngeloGioacchino Del Regno (2):
interconnect: qcom: Add SDM660 interconnect provider driver
dt-bindings: interconnect: Add bindings for Qualcomm SDM660 NoC
AngeloGioacchino Del Regno (2):
interconnect: qcom: Add SDM660 interconnect provider driver
dt-bindings: interconnect: Add bindings for Qualcomm SDM660 NoC
.../bindings/interconnect/qcom,sdm660.yaml | 147 +++ drivers/interconnect/qcom/Kconfig | 9 + drivers/interconnect/qcom/Makefile | 2 + drivers/interconnect/qcom/sdm660.c | 919 ++++++++++++++++++ .../dt-bindings/interconnect/qcom,sdm660.h | 116 +++ 5 files changed, 1193 insertions(+) create mode 100644 Documentation/devicetree/bindings/interconnect/qcom,sdm660.yaml create mode 100644 drivers/interconnect/qcom/sdm660.c create mode 100644 include/dt-bindings/interconnect/qcom,sdm660.h
Signature · 1 line
2.28.0
PATCH v2 1/2 interconnect: qcom: Add SDM660 interconnect provider driver
From: AngeloGioacchino Del Regno <[email protected]>
Introduce a driver for the Qualcomm interconnect busses found in the SDM630/SDM636/SDM660 SoCs.
The topology consists of several NoCs that are controlled by a remote processor that collects the aggregated bandwidth for each master-slave pairs.
On a note, these chips are managing the "bus QoS" in a "hybrid"
fashion: some of the paths in the topology are managed through (and by, of course) the RPM uC, while some others are "AP Owned", meaning that the AP shall do direct writes to the appropriate QoS registers for the specific paths and ports, instead of sending an indication to the RPM and leaving the job to that one.
--- drivers/interconnect/qcom/Kconfig | 9 + drivers/interconnect/qcom/Makefile | 2 + drivers/interconnect/qcom/sdm660.c | 919 ++++++++++++++++++ .../dt-bindings/interconnect/qcom,sdm660.h | 116 +++ 4 files changed, 1046 insertions(+) create mode 100644 drivers/interconnect/qcom/sdm660.c create mode 100644 include/dt-bindings/interconnect/qcom,sdm660.h
drivers/interconnect/qcom/Kconfig +9 -0
@@ -42,6 +42,15 @@ config INTERCONNECT_QCOM_QCS404 This is a driver for the Qualcomm Network-on-Chip on qcs404-based platforms. +config INTERCONNECT_QCOM_SDM660 + tristate "Qualcomm SDM660 interconnect driver" + depends on INTERCONNECT_QCOM + depends on QCOM_SMD_RPM + select INTERCONNECT_QCOM_SMD_RPM + help + This is a driver for the Qualcomm Network-on-Chip on sdm660-based + platforms. + config INTERCONNECT_QCOM_RPMH tristate
drivers/interconnect/qcom/Makefile +2 -0
@@ -7,6 +7,7 @@ icc-osm-l3-objs := osm-l3.o qnoc-qcs404-objs := qcs404.o icc-rpmh-obj := icc-rpmh.o qnoc-sc7180-objs := sc7180.o +qnoc-sdm660-objs := sdm660.o qnoc-sdm845-objs := sdm845.o qnoc-sm8150-objs := sm8150.o qnoc-sm8250-objs := sm8250.o
@@ -19,6 +20,7 @@ obj-$(CONFIG_INTERCONNECT_QCOM_OSM_L3) += icc-osm-l3.o obj-$(CONFIG_INTERCONNECT_QCOM_QCS404) += qnoc-qcs404.o obj-$(CONFIG_INTERCONNECT_QCOM_RPMH) += icc-rpmh.o obj-$(CONFIG_INTERCONNECT_QCOM_SC7180) += qnoc-sc7180.o +obj-$(CONFIG_INTERCONNECT_QCOM_SDM660) += qnoc-sdm660.o obj-$(CONFIG_INTERCONNECT_QCOM_SDM845) += qnoc-sdm845.o obj-$(CONFIG_INTERCONNECT_QCOM_SM8150) += qnoc-sm8150.o obj-$(CONFIG_INTERCONNECT_QCOM_SM8250) += qnoc-sm8250.o
drivers/interconnect/qcom/sdm660.c new file +919 -0
919 lines not on this page · raw message
include/dt-bindings/interconnect/qcom,sdm660.h new file +116 -0
116 lines not on this page · raw message
Signature · 1 line
2.28.0
Rob Herring
maintainerRe: [PATCH v2 1/2] interconnect: qcom: Add SDM660 interconnect provider driver
Quoted 15 lines · On Mon, Sep 28, 2020 at 09:58:52PM +0200, [email protected] wrote:
From: AngeloGioacchino Del Regno <[email protected]>
Introduce a driver for the Qualcomm interconnect busses found in the SDM630/SDM636/SDM660 SoCs.
The topology consists of several NoCs that are controlled by a remote processor that collects the aggregated bandwidth for each master-slave pairs.On a note, these chips are managing the "bus QoS" in a "hybrid"
fashion: some of the paths in the topology are managed through (and by, of course) the RPM uC, while some others are "AP Owned", meaning that the AP shall do direct writes to the appropriate QoS registers for the specific paths and ports, instead of sending an indication to the RPM and leaving the job to that one.
Quoted 6 lines
Signed-off-by AngeloGioacchino Del Regno <[email protected]>--- drivers/interconnect/qcom/Kconfig | 9 + drivers/interconnect/qcom/Makefile | 2 + drivers/interconnect/qcom/sdm660.c | 919 ++++++++++++++++++ .../dt-bindings/interconnect/qcom,sdm660.h | 116 +++
This goes with the binding.
Quoted 3 lines
4 files changed, 1046 insertions(+) create mode 100644 drivers/interconnect/qcom/sdm660.c create mode 100644 include/dt-bindings/interconnect/qcom,sdm660.h
PATCH v2 2/2 dt-bindings: interconnect: Add bindings for Qualcomm SDM660 NoC
In reply to [email protected]From: AngeloGioacchino Del Regno <[email protected]>
Add the bindings for the Qualcomm SDM660-class NoC, valid for SDM630, SDM636, SDM660 and SDA variants.
--- .../bindings/interconnect/qcom,sdm660.yaml | 147 ++++++++++++++++++ 1 file changed, 147 insertions(+) create mode 100644 Documentation/devicetree/bindings/interconnect/qcom,sdm660.yaml
Documentation/devicetree/bindings/interconnect/qcom,sdm660.yaml new file +147 -0
@@ -0,0 +1,147 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/interconnect/qcom,sdm660.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SDM660 Network-On-Chip interconnect + +maintainers: + - Georgi Djakov <[email protected]> + +description: | + The Qualcomm SDM660 interconnect providers support adjusting the + bandwidth requirements between the various NoC fabrics. + +properties: + reg: + maxItems: 1 + + compatible: + enum: + - qcom,sdm660-a2noc + - qcom,sdm660-bimc + - qcom,sdm660-cnoc + - qcom,sdm660-gnoc + - qcom,sdm660-mnoc + - qcom,sdm660-snoc + + '#interconnect-cells': + const: 1 + + clocks: + minItems: 1 + maxItems: 3 + + clock-names: + minItems: 1 + maxItems: 3 + +required: + - compatible + - reg + - '#interconnect-cells' + - clock-names + - clocks + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + enum: + - qcom,sdm660-mnoc + then: + properties: + clocks: + items: + - description: Bus Clock. + - description: Bus A Clock. + - description: CPU-NoC High-performance Bus Clock. + clock-names: + items: + - const: bus + - const: bus_a + - const: iface + + - if: + properties: + compatible: + contains: + enum: + - qcom,sdm660-a2noc + - qcom,sdm660-bimc + - qcom,sdm660-cnoc + - qcom,sdm660-gnoc + - qcom,sdm660-snoc + then: + properties: + clocks: + items: + - description: Bus Clock. + - description: Bus A Clock. + clock-names: + items: + - const: bus + - const: bus_a + +examples: + - | + #include <dt-bindings/clock/qcom,rpmcc.h> + #include <dt-bindings/clock/qcom,mmcc-sdm660.h> + + bimc: interconnect@1008000 { + compatible = "qcom,sdm660-bimc"; + reg = <0x01008000 0x78000>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_BIMC_CLK>, + <&rpmcc RPM_SMD_BIMC_A_CLK>; + }; + + cnoc: interconnect@1500000 { + compatible = "qcom,sdm660-cnoc"; + reg = <0x01500000 0x10000>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_CNOC_CLK>, + <&rpmcc RPM_SMD_CNOC_A_CLK>; + }; + + snoc: interconnect@1626000 { + compatible = "qcom,sdm660-snoc"; + reg = <0x01626000 0x7090>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_SNOC_CLK>, + <&rpmcc RPM_SMD_SNOC_A_CLK>; + }; + + a2noc: interconnect@1704000 { + compatible = "qcom,sdm660-a2noc"; + reg = <0x01704000 0xc100>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_AGGR2_NOC_CLK>, + <&rpmcc RPM_SMD_AGGR2_NOC_A_CLK>; + }; + + mnoc: interconnect@1745000 { + compatible = "qcom,sdm660-mnoc"; + reg = <0x01745000 0xa010>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a", "iface"; + clocks = <&rpmcc RPM_SMD_MMSSNOC_AXI_CLK>, + <&rpmcc RPM_SMD_MMSSNOC_AXI_CLK_A>, + <&mmcc AHB_CLK_SRC>; + }; + + gnoc: interconnect@17900000 { + compatible = "qcom,sdm660-gnoc"; + reg = <0x17900000 0xe000>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&xo_board>, <&xo_board>; + };
Signature · 1 line
2.28.0
Rob Herring
maintainerRe: [PATCH v2 2/2] dt-bindings: interconnect: Add bindings for Qualcomm SDM660 NoC
Quoted 11 lines · On Mon, 28 Sep 2020 21:58:53 +0200, [email protected] wrote:
From: AngeloGioacchino Del Regno <[email protected]>
Add the bindings for the Qualcomm SDM660-class NoC, valid for SDM630, SDM636, SDM660 and SDA variants.
Signed-off-by AngeloGioacchino Del Regno <[email protected]>--- .../bindings/interconnect/qcom,sdm660.yaml | 147 ++++++++++++++++++ 1 file changed, 147 insertions(+) create mode 100644 Documentation/devicetree/bindings/interconnect/qcom,sdm660.yaml
My bot found errors running 'make dt_binding_check' on your patch:
Documentation/devicetree/bindings/interconnect/qcom,sdm660.example.dts:20:18: fatal error: dt-bindings/clock/qcom,mmcc-sdm660.h: No such file or directory
20 | #include <dt-bindings/clock/qcom,mmcc-sdm660.h>
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
compilation terminated.
make[1]: *** [scripts/Makefile.lib:342: Documentation/devicetree/bindings/interconnect/qcom,sdm660.example.dt.yaml] Error 1 make[1]: *** Waiting for unfinished jobs....
make: *** [Makefile:1366: dt_binding_check] Error 2
See https://patchwork.ozlabs.org/patch/1372879
If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure dt-schema is up to date:
pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
Rob Herring
maintainerRe: [PATCH v2 2/2] dt-bindings: interconnect: Add bindings for Qualcomm SDM660 NoC
In reply to [email protected]Quoted 40 lines · On Mon, Sep 28, 2020 at 09:58:53PM +0200, [email protected] wrote:
From: AngeloGioacchino Del Regno <[email protected]>
Add the bindings for the Qualcomm SDM660-class NoC, valid for SDM630, SDM636, SDM660 and SDA variants.
Signed-off-by AngeloGioacchino Del Regno <[email protected]>--- .../bindings/interconnect/qcom,sdm660.yaml | 147 ++++++++++++++++++ 1 file changed, 147 insertions(+) create mode 100644 Documentation/devicetree/bindings/interconnect/qcom,sdm660.yamlDocumentation/devicetree/bindings/interconnect/qcom,sdm660.yaml new file +23
-0@@ -0,0 +1,147 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/interconnect/qcom,sdm660.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SDM660 Network-On-Chip interconnect + +maintainers: + - Georgi Djakov <[email protected]> + +description: | + The Qualcomm SDM660 interconnect providers support adjusting the + bandwidth requirements between the various NoC fabrics. + +properties: + reg: + maxItems: 1 + + compatible: + enum: + - qcom,sdm660-a2noc + - qcom,sdm660-bimc
Documentation/devicetree/bindings/interconnect/qcom,sdm660.yaml line 33
Quoted 10 lines
Documentation/devicetree/bindings/interconnect/qcom,sdm660.yaml new file +10
-0+ - qcom,sdm660-cnoc + - qcom,sdm660-gnoc + - qcom,sdm660-mnoc + - qcom,sdm660-snoc + + '#interconnect-cells': + const: 1 + + clocks: + minItems: 1
Looks like 2 is the min?
Quoted 24 lines
Documentation/devicetree/bindings/interconnect/qcom,sdm660.yaml new file +24
-0+ maxItems: 3 + + clock-names: + minItems: 1 + maxItems: 3 + +required: + - compatible + - reg + - '#interconnect-cells' + - clock-names + - clocks + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + enum: + - qcom,sdm660-mnoc + then: + properties:
Documentation/devicetree/bindings/interconnect/qcom,sdm660.yaml line 67
Quoted 10 lines
Documentation/devicetree/bindings/interconnect/qcom,sdm660.yaml new file +10
-0+ clocks: + items: + - description: Bus Clock. + - description: Bus A Clock. + - description: CPU-NoC High-performance Bus Clock. + clock-names: + items: + - const: bus + - const: bus_a + - const: iface
Given both cases are the same except the 3rd clock, all this can be moved to the main section. Then here you just need to restrict things to 2 or 3 clocks.
Quoted 83 lines
Documentation/devicetree/bindings/interconnect/qcom,sdm660.yaml new file +80
-0+ + - if: + properties: + compatible: + contains: + enum: + - qcom,sdm660-a2noc + - qcom,sdm660-bimc + - qcom,sdm660-cnoc + - qcom,sdm660-gnoc + - qcom,sdm660-snoc + then: + properties: + clocks: + items: + - description: Bus Clock. + - description: Bus A Clock. + clock-names: + items: + - const: bus + - const: bus_a + +examples: + - | + #include <dt-bindings/clock/qcom,rpmcc.h> + #include <dt-bindings/clock/qcom,mmcc-sdm660.h> + + bimc: interconnect@1008000 { + compatible = "qcom,sdm660-bimc"; + reg = <0x01008000 0x78000>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_BIMC_CLK>, + <&rpmcc RPM_SMD_BIMC_A_CLK>; + }; + + cnoc: interconnect@1500000 { + compatible = "qcom,sdm660-cnoc"; + reg = <0x01500000 0x10000>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_CNOC_CLK>, + <&rpmcc RPM_SMD_CNOC_A_CLK>; + }; + + snoc: interconnect@1626000 { + compatible = "qcom,sdm660-snoc"; + reg = <0x01626000 0x7090>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_SNOC_CLK>, + <&rpmcc RPM_SMD_SNOC_A_CLK>; + }; + + a2noc: interconnect@1704000 { + compatible = "qcom,sdm660-a2noc"; + reg = <0x01704000 0xc100>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_AGGR2_NOC_CLK>, + <&rpmcc RPM_SMD_AGGR2_NOC_A_CLK>; + }; + + mnoc: interconnect@1745000 { + compatible = "qcom,sdm660-mnoc"; + reg = <0x01745000 0xa010>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a", "iface"; + clocks = <&rpmcc RPM_SMD_MMSSNOC_AXI_CLK>, + <&rpmcc RPM_SMD_MMSSNOC_AXI_CLK_A>, + <&mmcc AHB_CLK_SRC>; + }; + + gnoc: interconnect@17900000 { + compatible = "qcom,sdm660-gnoc"; + reg = <0x17900000 0xe000>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&xo_board>, <&xo_board>; + };Signature · 1 line
2.28.0