Skip to contentSkip to conversation

spi: mvebu_a3700_spi: add support for cs-gpios

PATCH New George Hilliard 2 participants 2 messages Sep 30, 2020 – Oct 14, 2020 SPI

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 spi: mvebu_a3700_spi: add support for cs-gpios

The device tree has a way to specify GPIO lines as chip selects. From the binding docs:

So if for example the controller has 2 CS lines, and the cs-gpios property looks like this:

cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>;

Then it should be configured so that num_chipselect = 4 with the following mapping:

cs0 : &gpio1 0 0
cs1 : native
cs2 : &gpio1 1 0
cs3 : &gpio1 2 0

Add support for this, while retaining backward-compatibility with existing device trees; the driver will preserve existing behavior if a cs-gpios list is not given, or if a particular line is specified as <0> (native).

This implementation is inspired by similar implementations in neighboring drivers for other platforms: atmega, mxc, etc.

---
 drivers/spi/mvebu_a3700_spi.c | 41 ++++++++++++++++++++++++++++++-----
 1 file changed, 35 insertions(+), 6 deletions(-)
drivers/spi/mvebu_a3700_spi.c +35 -6
index e860b9ec64..eb13cf349e 100644
@@ -15,6 +15,7 @@
 #include <asm/io.h>
 #include <dm/device_compat.h>
 #include <linux/bitops.h>
+#include <asm/gpio.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -27,6 +28,7 @@ DECLARE_GLOBAL_DATA_PTR;
 #define MVEBU_SPI_A3700_SPI_EN_0		BIT(16)
 #define MVEBU_SPI_A3700_CLK_PRESCALE_MASK	0x1f
 
+#define MAX_CS_COUNT	4
 
 /* SPI registers */
 struct spi_reg {
@@ -39,16 +41,23 @@ struct spi_reg {
 struct mvebu_spi_platdata {
 	struct spi_reg *spireg;
 	struct clk clk;
+	struct gpio_desc cs_gpios[MAX_CS_COUNT];
 };
 
-static void spi_cs_activate(struct spi_reg *reg, int cs)
+static void spi_cs_activate(struct mvebu_spi_platdata *plat, int cs)
 {
-	setbits_le32(&reg->ctrl, MVEBU_SPI_A3700_SPI_EN_0 << cs);
+	if (CONFIG_IS_ENABLED(DM_GPIO) && dm_gpio_is_valid(&plat->cs_gpios[cs]))
+		dm_gpio_set_value(&plat->cs_gpios[cs], 1);
+	else
+		setbits_le32(&plat->spireg->ctrl, MVEBU_SPI_A3700_SPI_EN_0 << cs);
 }
 
-static void spi_cs_deactivate(struct spi_reg *reg, int cs)
+static void spi_cs_deactivate(struct mvebu_spi_platdata *plat, int cs)
 {
-	clrbits_le32(&reg->ctrl, MVEBU_SPI_A3700_SPI_EN_0 << cs);
+	if (CONFIG_IS_ENABLED(DM_GPIO) && dm_gpio_is_valid(&plat->cs_gpios[cs]))
+		dm_gpio_set_value(&plat->cs_gpios[cs], 0);
+	else
+		clrbits_le32(&plat->spireg->ctrl, MVEBU_SPI_A3700_SPI_EN_0 << cs);
 }
 
 /**
@@ -150,7 +159,7 @@ static int mvebu_spi_xfer(struct udevice *dev, unsigned int bitlen,
 	/* Activate CS */
 	if (flags & SPI_XFER_BEGIN) {
 		debug("SPI: activate cs.\n");
-		spi_cs_activate(reg, spi_chip_select(dev));
+		spi_cs_activate(plat, spi_chip_select(dev));
 	}
 
 	/* Send and/or receive */
@@ -169,7 +178,7 @@ static int mvebu_spi_xfer(struct udevice *dev, unsigned int bitlen,
 			return ret;
 
 		debug("SPI: deactivate cs.\n");
-		spi_cs_deactivate(reg, spi_chip_select(dev));
+		spi_cs_deactivate(plat, spi_chip_select(dev));
 	}
 
 	return 0;
@@ -247,6 +256,26 @@ static int mvebu_spi_probe(struct udevice *bus)
 
 	writel(data, &reg->cfg);
 
+	/* Set up CS GPIOs in device tree, if any */
+	if (CONFIG_IS_ENABLED(DM_GPIO) && gpio_get_list_count(bus, "cs-gpios") > 0) {
+		int i;
+
+		for (i = 0; i < ARRAY_SIZE(plat->cs_gpios); i++) {
+			ret = gpio_request_by_name(bus, "cs-gpios", i, &plat->cs_gpios[i], 0);
+			if (ret < 0 || !dm_gpio_is_valid(&plat->cs_gpios[i])) {
+				/* Use the native CS function for this line */
+				continue;
+			}
+
+			ret = dm_gpio_set_dir_flags(&plat->cs_gpios[i],
+						    GPIOD_IS_OUT | GPIOD_ACTIVE_LOW);
+			if (ret) {
+				dev_err(bus, "Setting cs %d error\n", i);
+				return ret;
+			}
+		}
+	}
+
 	return 0;
 }
 
Signature · 1 line
2.23.3
#1 lore raw

PATCH v3 1/1 spi: mvebu_a3700_spi: add support for cs-gpios

Quoted 21 lines · George Hilliard

The device tree has a way to specify GPIO lines as chip selects. From the binding docs:

So if for example the controller has 2 CS lines, and the cs-gpios property looks like this:

cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>;

Then it should be configured so that num_chipselect = 4 with the following mapping:

cs0 : &gpio1 0 0
cs1 : native
cs2 : &gpio1 1 0
cs3 : &gpio1 2 0

Add support for this, while retaining backward-compatibility with existing device trees; the driver will preserve existing behavior if a cs-gpios list is not given, or if a particular line is specified as <0> (native).

Quoted 5 lines

This implementation is inspired by similar implementations in neighboring drivers for other platforms: atmega, mxc, etc.

Applied to u-boot-marvell/master

Thanks,
Stefan

Quoted 88 lines
---
  drivers/spi/mvebu_a3700_spi.c | 41 ++++++++++++++++++++++++++++++-----
  1 file changed, 35 insertions(+), 6 deletions(-)
drivers/spi/mvebu_a3700_spi.c +28 -6
index e860b9ec64..eb13cf349e 100644
@@ -15,6 +15,7 @@
  #include <asm/io.h>
  #include <dm/device_compat.h>
  #include <linux/bitops.h>
+#include <asm/gpio.h>
 
  DECLARE_GLOBAL_DATA_PTR;
 
@@ -27,6 +28,7 @@ DECLARE_GLOBAL_DATA_PTR;
  #define MVEBU_SPI_A3700_SPI_EN_0		BIT(16)
  #define MVEBU_SPI_A3700_CLK_PRESCALE_MASK	0x1f
 
+#define MAX_CS_COUNT	4
 
  /* SPI registers */
  struct spi_reg {
@@ -39,16 +41,23 @@ struct spi_reg {
  struct mvebu_spi_platdata {
  	struct spi_reg *spireg;
  	struct clk clk;
+	struct gpio_desc cs_gpios[MAX_CS_COUNT];
  };
 
-static void spi_cs_activate(struct spi_reg *reg, int cs)
+static void spi_cs_activate(struct mvebu_spi_platdata *plat, int cs)
  {
-	setbits_le32(&reg->ctrl, MVEBU_SPI_A3700_SPI_EN_0 << cs);
+	if (CONFIG_IS_ENABLED(DM_GPIO) && dm_gpio_is_valid(&plat->cs_gpios[cs]))
+		dm_gpio_set_value(&plat->cs_gpios[cs], 1);
+	else
+		setbits_le32(&plat->spireg->ctrl, MVEBU_SPI_A3700_SPI_EN_0 << cs);
  }
 
-static void spi_cs_deactivate(struct spi_reg *reg, int cs)
+static void spi_cs_deactivate(struct mvebu_spi_platdata *plat, int cs)
  {
-	clrbits_le32(&reg->ctrl, MVEBU_SPI_A3700_SPI_EN_0 << cs);
+	if (CONFIG_IS_ENABLED(DM_GPIO) && dm_gpio_is_valid(&plat->cs_gpios[cs]))
+		dm_gpio_set_value(&plat->cs_gpios[cs], 0);
+	else
+		clrbits_le32(&plat->spireg->ctrl, MVEBU_SPI_A3700_SPI_EN_0 << cs);
  }
 
  /**
@@ -150,7 +159,7 @@ static int mvebu_spi_xfer(struct udevice *dev, unsigned int bitlen,
  	/* Activate CS */
  	if (flags & SPI_XFER_BEGIN) {
  		debug("SPI: activate cs.\n");
-		spi_cs_activate(reg, spi_chip_select(dev));
+		spi_cs_activate(plat, spi_chip_select(dev));
  	}
 
  	/* Send and/or receive */
@@ -169,7 +178,7 @@ static int mvebu_spi_xfer(struct udevice *dev, unsigned int bitlen,
  			return ret;
 
  		debug("SPI: deactivate cs.\n");
-		spi_cs_deactivate(reg, spi_chip_select(dev));
+		spi_cs_deactivate(plat, spi_chip_select(dev));
  	}
 
  	return 0;
@@ -247,6 +256,26 @@ static int mvebu_spi_probe(struct udevice *bus)
 
  	writel(data, &reg->cfg);
 
+	/* Set up CS GPIOs in device tree, if any */
+	if (CONFIG_IS_ENABLED(DM_GPIO) && gpio_get_list_count(bus, "cs-gpios") > 0) {
+		int i;
+
+		for (i = 0; i < ARRAY_SIZE(plat->cs_gpios); i++) {
+			ret = gpio_request_by_name(bus, "cs-gpios", i, &plat->cs_gpios[i], 0);
+			if (ret < 0 || !dm_gpio_is_valid(&plat->cs_gpios[i])) {
+				/* Use the native CS function for this line */
+				continue;
+			}
+
+			ret = dm_gpio_set_dir_flags(&plat->cs_gpios[i],
+						    GPIOD_IS_OUT | GPIOD_ACTIVE_LOW);

drivers/spi/mvebu_a3700_spi.c static int mvebu_spi_probe(struct udevice *bus) · line 281

Quoted 10 lines
drivers/spi/mvebu_a3700_spi.c +7 -0
+			if (ret) {
+				dev_err(bus, "Setting cs %d error\n", i);
+				return ret;
+			}
+		}
+	}
+
  	return 0;
  }
 

Viele Gr??e,
Stefan

Signature · 3 lines
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de