add Intel MAX 10 BMC MFD driver & hwmon sub driver
Subsystems (3)
Xu Yilun
maintainerv3 cover add Intel MAX 10 BMC MFD driver & hwmon sub driver
I recently realized that maintainers may have trouble to apply patches to their trees if the patches depend on other being-reviewed patches. So I'm trying to wrapper the 2 patches into one patchset and let all the maintainers see the dependencies.
But the patch version is then not aligned between the 2 patches. I'm not sure how to handle it. I just picked the smaller number on Subject, but you could still see their own version changes in commit message of each patch. Sorry if it makes confusing.
Patch #1 implements the basic functions of the BMC chip for some Intel FPGA PCIe Acceleration Cards (PAC). The BMC is implemented using the Intel MAX 10 CPLD.
This BMC chip is connected to the FPGA by a SPI bus. To provide direct register access from the FPGA, the "SPI slave to Avalon Master Bridge" (spi-avmm) IP is integrated in the chip. It converts encoded streams of bytes from the host to the internal register read/write on the Avalon bus. So This driver uses the regmap-spi-avmm for register accessing.
Patch #2 adds support for the hwmon sub device in Intel MAX 10 BMC
Xu Yilun (2):
mfd: intel-m10-bmc: add Intel MAX 10 BMC chip support for Intel FPGA
PAC
hwmon: intel-m10-bmc-hwmon: add hwmon support for Intel MAX 10 BMC
.../ABI/testing/sysfs-driver-intel-m10-bmc | 15 + Documentation/hwmon/index.rst | 1 + Documentation/hwmon/intel-m10-bmc-hwmon.rst | 78 +++++ drivers/hwmon/Kconfig | 11 + drivers/hwmon/Makefile | 1 + drivers/hwmon/intel-m10-bmc-hwmon.c | 334 +++++++++++++++++++++ drivers/mfd/Kconfig | 13 + drivers/mfd/Makefile | 2 + drivers/mfd/intel-m10-bmc.c | 164 ++++++++++ include/linux/mfd/intel-m10-bmc.h | 65 ++++ 10 files changed, 684 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-driver-intel-m10-bmc create mode 100644 Documentation/hwmon/intel-m10-bmc-hwmon.rst create mode 100644 drivers/hwmon/intel-m10-bmc-hwmon.c create mode 100644 drivers/mfd/intel-m10-bmc.c create mode 100644 include/linux/mfd/intel-m10-bmc.h
Signature · 1 line
2.7.4
Xu Yilun
maintainerPATCH v3 2/2 hwmon: intel-m10-bmc-hwmon: add hwmon support for Intel MAX 10 BMC
This patch adds hwmon functionality for Intel MAX 10 BMC chip. This BMC chip connects to a set of sensor chips to monitor current, voltage, thermal and power of different components on board. The BMC firmware is responsible for sensor data sampling and recording in shared registers. Host driver reads the sensor data from these shared registers and exposes them to users as hwmon interfaces.
---
v2: add the Documentation
refactor the code, provide static hwmon_channel_info remove Unnecessary hwmon-sysfs.h
make the sensor data table const
v3: make the data tables a pointer array indexed by hwmon_sensor_types
some minor fixes
--- Documentation/hwmon/index.rst | 1 + Documentation/hwmon/intel-m10-bmc-hwmon.rst | 78 +++++++ drivers/hwmon/Kconfig | 11 + drivers/hwmon/Makefile | 1 + drivers/hwmon/intel-m10-bmc-hwmon.c | 334 ++++++++++++++++++++++++++++ 5 files changed, 425 insertions(+) create mode 100644 Documentation/hwmon/intel-m10-bmc-hwmon.rst create mode 100644 drivers/hwmon/intel-m10-bmc-hwmon.c
Documentation/hwmon/index.rst +1 -0
@@ -74,6 +74,7 @@ Hardware Monitoring Kernel Drivers ina209 ina2xx ina3221 + intel-m10-bmc-hwmon ir35221 ir38064 isl68137
Documentation/hwmon/intel-m10-bmc-hwmon.rst new file +78 -0
78 lines not on this page · raw message
drivers/hwmon/Kconfig +11 -0
@@ -2064,6 +2064,17 @@ config SENSORS_XGENE If you say yes here you get support for the temperature and power sensors for APM X-Gene SoC. +config SENSORS_INTEL_M10_BMC_HWMON + tristate "Intel MAX10 BMC Hardware Monitoring" + depends on MFD_INTEL_M10_BMC + help + This driver provides support for the hardware monitoring functionality + on Intel MAX10 BMC chip. + + This BMC Chip is used on Intel FPGA PCIe Acceleration Cards (PAC). Its + sensors monitor various telemetry data of different components on the + card, e.g. board temperature, FPGA core temperature/voltage/current. + if ACPI comment "ACPI drivers"
drivers/hwmon/Makefile +1 -0
@@ -90,6 +90,7 @@ obj-$(CONFIG_SENSORS_IIO_HWMON) += iio_hwmon.o obj-$(CONFIG_SENSORS_INA209) += ina209.o obj-$(CONFIG_SENSORS_INA2XX) += ina2xx.o obj-$(CONFIG_SENSORS_INA3221) += ina3221.o +obj-$(CONFIG_SENSORS_INTEL_M10_BMC_HWMON) += intel-m10-bmc-hwmon.o obj-$(CONFIG_SENSORS_IT87) += it87.o obj-$(CONFIG_SENSORS_JC42) += jc42.o obj-$(CONFIG_SENSORS_K8TEMP) += k8temp.o
drivers/hwmon/intel-m10-bmc-hwmon.c new file +334 -0
334 lines not on this page · raw message
Signature · 1 line
2.7.4
Re: [PATCH v3 2/2] hwmon: intel-m10-bmc-hwmon: add hwmon support for Intel MAX 10 BMC
Quoted 11 lines · Xu Yilun
This patch adds hwmon functionality for Intel MAX 10 BMC chip. This BMC chip connects to a set of sensor chips to monitor current, voltage, thermal and power of different components on board. The BMC firmware is responsible for sensor data sampling and recording in shared registers. Host driver reads the sensor data from these shared registers and exposes them to users as hwmon interfaces.
Signed-off-by Xu Yilun <[email protected]>Signed-off-by Wu Hao <[email protected]>Signed-off-by Matthew Gerlach <[email protected]>Signed-off-by Tom Rix <[email protected]>
Quoted 488 lines
---
v2: add the Documentation
refactor the code, provide statichwmon_channel_inforemove Unnecessaryhwmon-sysfs.h
make the sensor data table const
v3: make the data tables a pointer array indexed byhwmon_sensor_types
some minor fixes--- Documentation/hwmon/index.rst | 1 + Documentation/hwmon/intel-m10-bmc-hwmon.rst | 78 +++++++ drivers/hwmon/Kconfig | 11 + drivers/hwmon/Makefile | 1 + drivers/hwmon/intel-m10-bmc-hwmon.c | 334 ++++++++++++++++++++++++++++ 5 files changed, 425 insertions(+) create mode 100644 Documentation/hwmon/intel-m10-bmc-hwmon.rst create mode 100644 drivers/hwmon/intel-m10-bmc-hwmon.cDocumentation/hwmon/index.rst +1
-0@@ -74,6 +74,7 @@ Hardware Monitoring Kernel Drivers ina209 ina2xx ina3221 + intel-m10-bmc-hwmon ir35221 ir38064 isl68137Documentation/hwmon/intel-m10-bmc-hwmon.rst new file +78
-0@@ -0,0 +1,78 @@ +.. SPDX-License-Identifier: GPL-2.0 + +Kernel driver intel-m10-bmc-hwmon +================================= + +Supported chips: + + * Intel MAX 10 BMC for Intel PAC N3000 + + Prefix: 'n3000bmc-hwmon' + +Author: Xu Yilun <[email protected]> + + +Description +----------- + +This driver adds the temperature, voltage, current and power reading +support for the Intel MAX 10 Board Management Controller (BMC) chip. +The BMC chip is integrated in some Intel Programmable Acceleration +Cards (PAC). It connects to a set of sensor chips to monitor the +sensor data of different components on the board. The BMC firmware is +responsible for sensor data sampling and recording in shared +registers. The host driver reads the sensor data from these shared +registers and exposes them to users as hwmon interfaces. + +The BMC chip is implemented using the Intel MAX 10 CPLD. It could be +reprogramed to some variants in order to support different Intel +PACs. The driver is designed to be able to distinguish between the +variants, but now it only supports the BMC for Intel PAC N3000. + + +Sysfs attributes +---------------- + +The following attributes are supported: + +- Intel MAX 10 BMC for Intel PAC N3000: + +======================= ======================================================= +tempX_input Temperature of the component (specified by tempX_label) +tempX_max Temperature maximum setpoint of the component +tempX_crit Temperature critical setpoint of the component +tempX_max_hyst Hysteresis for temperature maximum of the component +tempX_crit_hyst Hysteresis for temperature critical of the component +temp1_label "Board Temperature" +temp2_label "FPGA Die Temperature" +temp3_label "QSFP0 Temperature" +temp4_label "QSFP1 Temperature" +temp5_label "Retimer A Temperature" +temp6_label "Retimer A SerDes Temperature" +temp7_label "Retimer B Temperature" +temp8_label "Retimer B SerDes Temperature" + +inX_input Measured voltage of the component (specified by + inX_label) +in0_label "QSFP0 Supply Voltage" +in1_label "QSFP1 Supply Voltage" +in2_label "FPGA Core Voltage" +in3_label "12V Backplane Voltage" +in4_label "1.2V Voltage" +in5_label "12V AUX Voltage" +in6_label "1.8V Voltage" +in7_label "3.3V Voltage" + +currX_input Measured current of the component (specified by + currX_label) +curr1_label "FPGA Core Current" +curr2_label "12V Backplane Current" +curr3_label "12V AUX Current" + +powerX_input Measured power of the component (specified by + powerX_label) +power1_label "Board Power" + +======================= ======================================================= + +All the attributes are read-only.drivers/hwmon/Kconfig +11
-0@@ -2064,6 +2064,17 @@ config SENSORS_XGENE If you say yes here you get support for the temperature and power sensors for APM X-Gene SoC. +config SENSORS_INTEL_M10_BMC_HWMON + tristate "Intel MAX10 BMC Hardware Monitoring" + depends on MFD_INTEL_M10_BMC + help + This driver provides support for the hardware monitoring functionality + on Intel MAX10 BMC chip. + + This BMC Chip is used on Intel FPGA PCIe Acceleration Cards (PAC). Its + sensors monitor various telemetry data of different components on the + card, e.g. board temperature, FPGA core temperature/voltage/current. + if ACPI comment "ACPI drivers"drivers/hwmon/Makefile +1
-0@@ -90,6 +90,7 @@ obj-$(CONFIG_SENSORS_IIO_HWMON) += iio_hwmon.o obj-$(CONFIG_SENSORS_INA209) += ina209.o obj-$(CONFIG_SENSORS_INA2XX) += ina2xx.o obj-$(CONFIG_SENSORS_INA3221) += ina3221.o +obj-$(CONFIG_SENSORS_INTEL_M10_BMC_HWMON) += intel-m10-bmc-hwmon.o obj-$(CONFIG_SENSORS_IT87) += it87.o obj-$(CONFIG_SENSORS_JC42) += jc42.o obj-$(CONFIG_SENSORS_K8TEMP) += k8temp.odrivers/hwmon/intel-m10-bmc-hwmon.c new file +334
-0@@ -0,0 +1,334 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* Intel MAX 10 BMC HWMON Driver +* +* Copyright (C) 2018-2020 Intel Corporation. All rights reserved. +* +*/ +#include <linux/device.h> +#include <linux/hwmon.h> +#include <linux/mfd/intel-m10-bmc.h> +#include <linux/module.h> +#include <linux/mod_devicetable.h> +#include <linux/platform_device.h> + +struct m10bmc_sdata { +unsigned int reg_input; +unsigned int reg_max; +unsigned int reg_crit; +unsigned int reg_hyst; +unsigned int reg_min; +unsigned int multiplier; +const char *label; +}; + +struct m10bmc_hwmon_board_data { +const struct m10bmc_sdata *tables[hwmon_max]; +const struct hwmon_channel_info **hinfo; +}; + +struct m10bmc_hwmon { +struct device *dev; +struct hwmon_chip_info chip; +char *hw_name; +struct intel_m10bmc *m10bmc; +const struct m10bmc_hwmon_board_data *bdata; +}; + +static const struct m10bmc_sdata n3000bmc_temp_tbl[] = { + {0x100 ,0x104 ,0x108 ,0x10c ,0x0 ,500 ,"Board Temperature" }, + {0x110 ,0x114 ,0x118 ,0x0 ,0x0 ,500 ,"FPGA Die Temperature" }, + {0x11c ,0x124 ,0x120 ,0x0 ,0x0 ,500 ,"QSFP0 Temperature" }, + {0x12c ,0x134 ,0x130 ,0x0 ,0x0 ,500 ,"QSFP1 Temperature" }, + {0x168 ,0x0 ,0x0 ,0x0 ,0x0 ,500 ,"Retimer A Temperature" }, + {0x16c ,0x0 ,0x0 ,0x0 ,0x0 ,500 ,"Retimer A SerDes Temperature" }, + {0x170 ,0x0 ,0x0 ,0x0 ,0x0 ,500 ,"Retimer B Temperature" }, + {0x174 ,0x0 ,0x0 ,0x0 ,0x0 ,500 ,"Retimer B SerDes Temperature" }, +}; + +static const struct m10bmc_sdata n3000bmc_in_tbl[] = { + {0x128 ,0x0 ,0x0 ,0x0 ,0x0 ,1 ,"QSFP0 Supply Voltage" }, + {0x138 ,0x0 ,0x0 ,0x0 ,0x0 ,1 ,"QSFP1 Supply Voltage" }, + {0x13c ,0x0 ,0x0 ,0x0 ,0x0 ,1 ,"FPGA Core Voltage" }, + {0x144 ,0x0 ,0x0 ,0x0 ,0x0 ,1 ,"12V Backplane Voltage" }, + {0x14c ,0x0 ,0x0 ,0x0 ,0x0 ,1 ,"1.2V Voltage" }, + {0x150 ,0x0 ,0x0 ,0x0 ,0x0 ,1 ,"12V AUX Voltage" }, + {0x158 ,0x0 ,0x0 ,0x0 ,0x0 ,1 ,"1.8V Voltage" }, + {0x15c ,0x0 ,0x0 ,0x0 ,0x0 ,1 ,"3.3V Voltage" }, +}; + +static const struct m10bmc_sdata n3000bmc_curr_tbl[] = { + {0x140 ,0x0 ,0x0 ,0x0 ,0x0 ,1 ,"FPGA Core Current" }, + {0x148 ,0x0 ,0x0 ,0x0 ,0x0 ,1 ,"12V Backplane Current" }, + {0x154 ,0x0 ,0x0 ,0x0 ,0x0 ,1 ,"12V AUX Current" }, +}; + +static const struct m10bmc_sdata n3000bmc_power_tbl[] = { + {0x160 ,0x0 ,0x0 ,0x0 ,0x0 ,1000 ,"Board Power" }, +}; + +static const struct hwmon_channel_info *n3000bmc_hinfo[] = { +HWMON_CHANNEL_INFO (temp, +HWMON_T_INPUT |HWMON_T_MAX |HWMON_T_MAX_HYST | +HWMON_T_CRIT |HWMON_T_CRIT_HYST |HWMON_T_LABEL , +HWMON_T_INPUT |HWMON_T_MAX |HWMON_T_CRIT | +HWMON_T_LABEL , +HWMON_T_INPUT |HWMON_T_MAX |HWMON_T_CRIT | +HWMON_T_LABEL , +HWMON_T_INPUT |HWMON_T_MAX |HWMON_T_CRIT | +HWMON_T_LABEL , +HWMON_T_INPUT |HWMON_T_LABEL , +HWMON_T_INPUT |HWMON_T_LABEL , +HWMON_T_INPUT |HWMON_T_LABEL , +HWMON_T_INPUT |HWMON_T_LABEL ), +HWMON_CHANNEL_INFO (in, +HWMON_I_INPUT |HWMON_I_LABEL , +HWMON_I_INPUT |HWMON_I_LABEL , +HWMON_I_INPUT |HWMON_I_LABEL , +HWMON_I_INPUT |HWMON_I_LABEL , +HWMON_I_INPUT |HWMON_I_LABEL , +HWMON_I_INPUT |HWMON_I_LABEL , +HWMON_I_INPUT |HWMON_I_LABEL , +HWMON_I_INPUT |HWMON_I_LABEL ), +HWMON_CHANNEL_INFO (curr, +HWMON_C_INPUT |HWMON_C_LABEL , +HWMON_C_INPUT |HWMON_C_LABEL , +HWMON_C_INPUT |HWMON_C_LABEL ), +HWMON_CHANNEL_INFO (power, +HWMON_P_INPUT |HWMON_P_LABEL ), +NULL +}; + +static const struct m10bmc_hwmon_board_data n3000bmc_hwmon_bdata = { + .tables = { + [hwmon_temp] = n3000bmc_temp_tbl, + [hwmon_in] = n3000bmc_in_tbl, + [hwmon_curr] = n3000bmc_curr_tbl, + [hwmon_power] = n3000bmc_power_tbl, + }, + + .hinfo = n3000bmc_hinfo, +}; + +static umode_t +m10bmc_hwmon_is_visible (const void *data,enum hwmon_sensor_types type, +u32 attr,int channel) +{ +return 0444 ; +} + +static const struct m10bmc_sdata * +find_sensor_data (struct m10bmc_hwmon *hw,enum hwmon_sensor_types type, +int channel) +{ +const struct m10bmc_sdata *tbl; + + tbl = hw->bdata->tables[type]; +if (!tbl) +return ERR_PTR (-EOPNOTSUPP ); + +return &tbl[channel]; +} + +static int do_sensor_read (struct m10bmc_hwmon *hw, +const struct m10bmc_sdata *data, +unsigned int regoff,long *val) +{ +unsigned int regval; +int ret; + + ret =m10bmc_sys_read (hw->m10bmc, regoff, ®val); +if (ret) +return ret; + +/* +* BMC Firmware will return 0xdeadbeef if the sensor value is invalid +* at that time. This usually happens on sensor channels which connect +* to external pluggable modules, e.g. QSFP temperature and voltage. +* When the QSFP is unplugged from cage, driver will get 0xdeadbeef +* from their registers. +*/ +if (regval ==0xdeadbeef ) +return -ENODATA ; + + *val = regval * data->multiplier; + +return 0 ; +} + +static int m10bmc_hwmon_read (struct device *dev,enum hwmon_sensor_types type, +u32 attr,int channel,long *val) +{ +struct m10bmc_hwmon *hw =dev_get_drvdata (dev); +unsigned int reg =0 , reg_hyst =0 ; +const struct m10bmc_sdata *data; +long hyst, value; +int ret; + + data =find_sensor_data (hw, type, channel); +if (IS_ERR (data)) +return PTR_ERR (data); + +switch (type) { +case hwmon_temp: +switch (attr) { +case hwmon_temp_input: + reg = data->reg_input; +break ; +case hwmon_temp_max_hyst: + reg_hyst = data->reg_hyst; + fallthrough; +case hwmon_temp_max: + reg = data->reg_max; +break ; +case hwmon_temp_crit_hyst: + reg_hyst = data->reg_hyst; + fallthrough; +case hwmon_temp_crit: + reg = data->reg_crit; +break ; +default : +return -EOPNOTSUPP ; + } +break ; +case hwmon_in: +switch (attr) { +case hwmon_in_input: + reg = data->reg_input; +break ; +case hwmon_in_max: + reg = data->reg_max; +break ; +case hwmon_in_crit: + reg = data->reg_crit; +break ; +case hwmon_in_min: + reg = data->reg_min; +break ; +default : +return -EOPNOTSUPP ; + } +break ; +case hwmon_curr: +switch (attr) { +case hwmon_curr_input: + reg = data->reg_input; +break ; +case hwmon_curr_max: + reg = data->reg_max; +break ; +case hwmon_curr_crit: + reg = data->reg_crit; +break ; +default : +return -EOPNOTSUPP ; + } +break ; +case hwmon_power: +switch (attr) { +case hwmon_power_input: + reg = data->reg_input; +break ; +default : +return -EOPNOTSUPP ; + } +break ; +default : +return -EOPNOTSUPP ; + } + +if (!reg) +return -EOPNOTSUPP ; + + ret =do_sensor_read (hw, data, reg, &value); +if (ret) +return ret; + +if (reg_hyst) { + ret =do_sensor_read (hw, data, reg_hyst, &hyst); +if (ret) +return ret; + + value -= hyst; + } + + *val = value; + +return 0 ; +} + +static int m10bmc_hwmon_read_string (struct device *dev, +enum hwmon_sensor_types type, +u32 attr,int channel,const char **str) +{ +struct m10bmc_hwmon *hw =dev_get_drvdata (dev); +const struct m10bmc_sdata *data; + + data =find_sensor_data (hw, type, channel); +if (IS_ERR (data)) +return PTR_ERR (data); + + *str = data->label; + +return 0 ; +} + +static const struct hwmon_ops m10bmc_hwmon_ops = { + .is_visible = m10bmc_hwmon_is_visible, + .read = m10bmc_hwmon_read, + .read_string = m10bmc_hwmon_read_string, +}; + +static int m10bmc_hwmon_probe (struct platform_device *pdev) +{ +const struct platform_device_id *id =platform_get_device_id (pdev); +struct intel_m10bmc *m10bmc =dev_get_drvdata (pdev->dev.parent); +struct device *hwmon_dev, *dev = &pdev->dev; +struct m10bmc_hwmon *hw; +int i; + + hw =devm_kzalloc (dev,sizeof (*hw),GFP_KERNEL ); +if (!hw) +return -ENOMEM ; + + hw->dev = dev; + hw->m10bmc = m10bmc; + hw->bdata = (const struct m10bmc_hwmon_board_data *)id->driver_data; + + hw->chip.info = hw->bdata->hinfo; + hw->chip.ops = &m10bmc_hwmon_ops; + + hw->hw_name =devm_kstrdup (dev, id->name,GFP_KERNEL ); +if (!hw->hw_name) +return -ENOMEM ; + +for (i =0 ; hw->hw_name[i]; i++) +if (hwmon_is_bad_char (hw->hw_name[i])) + hw->hw_name[i] ='_' ; + + hwmon_dev =devm_hwmon_device_register_with_info (dev, hw->hw_name, + hw, &hw->chip,NULL ); +return PTR_ERR_OR_ZERO (hwmon_dev); +} + +static const struct platform_device_id intel_m10bmc_hwmon_ids[] = { + { + .name ="n3000bmc-hwmon" , + .driver_data = (unsigned long )&n3000bmc_hwmon_bdata, + }, + { } +}; + +static struct platform_driver intel_m10bmc_hwmon_driver = { + .probe = m10bmc_hwmon_probe, + .driver = { + .name ="intel-m10-bmc-hwmon" , + }, + .id_table = intel_m10bmc_hwmon_ids, +}; +module_platform_driver (intel_m10bmc_hwmon_driver); + +MODULE_DEVICE_TABLE (platform, intel_m10bmc_hwmon_ids); +MODULE_AUTHOR ("Intel Corporation" ); +MODULE_DESCRIPTION ("Intel MAX 10 BMC hardware monitor" ); +MODULE_LICENSE ("GPL" );
Guenter Roeck
maintainerQuoted 10 lines · Xu Yilun
I recently realized that maintainers may have trouble to apply patches to their trees if the patches depend on other being-reviewed patches. So I'm trying to wrapper the 2 patches into one patchset and let all the maintainers see the dependencies.
But the patch version is then not aligned between the 2 patches. I'm not sure how to handle it. I just picked the smaller number on Subject, but you could still see their own version changes in commit message of each patch. Sorry if it makes confusing.
If you started with separate patches, it would be much better to pick the larger number, and add a note into the individual patch(es) stating the reason for the gap. Everything else is highly confusing. I would not be surprised if no one in the mfd world even looks at the mfd patch since it went back from v6 (?) to v3 according to its subject line.
Thanks,
Guenter
Quoted 39 lines
Patch #1 implements the basic functions of the BMC chip for some Intel FPGA PCIe Acceleration Cards (PAC). The BMC is implemented using the Intel MAX 10 CPLD.
This BMC chip is connected to the FPGA by a SPI bus. To provide direct register access from the FPGA, the "SPI slave to Avalon Master Bridge" (spi-avmm) IP is integrated in the chip. It converts encoded streams of bytes from the host to the internal register read/write on the Avalon bus. So This driver uses the regmap-spi-avmm for register accessing.
Patch #2 adds support for the hwmon sub device in Intel MAX 10 BMC
Xu Yilun (2):
mfd: intel-m10-bmc: add Intel MAX 10 BMC chip support for Intel FPGA
PAC
hwmon: intel-m10-bmc-hwmon: add hwmon support for Intel MAX 10 BMC.../ABI/testing/sysfs-driver-intel-m10-bmc | 15 + Documentation/hwmon/index.rst | 1 + Documentation/hwmon/intel-m10-bmc-hwmon.rst | 78 +++++ drivers/hwmon/Kconfig | 11 + drivers/hwmon/Makefile | 1 + drivers/hwmon/intel-m10-bmc-hwmon.c | 334 +++++++++++++++++++++ drivers/mfd/Kconfig | 13 + drivers/mfd/Makefile | 2 + drivers/mfd/intel-m10-bmc.c | 164 ++++++++++ include/linux/mfd/intel-m10-bmc.h | 65 ++++ 10 files changed, 684 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-driver-intel-m10-bmc create mode 100644 Documentation/hwmon/intel-m10-bmc-hwmon.rst create mode 100644 drivers/hwmon/intel-m10-bmc-hwmon.c create mode 100644 drivers/mfd/intel-m10-bmc.c create mode 100644 include/linux/mfd/intel-m10-bmc.hSignature · 1 line
2.7.4
Xu Yilun
maintainerHi Guenter,
Quoted 12 lines · Guenter Roeck
Quoted 10 lines · Xu Yilun
I recently realized that maintainers may have trouble to apply patches to their trees if the patches depend on other being-reviewed patches. So I'm trying to wrapper the 2 patches into one patchset and let all the maintainers see the dependencies.
But the patch version is then not aligned between the 2 patches. I'm not sure how to handle it. I just picked the smaller number on Subject, but you could still see their own version changes in commit message of each patch. Sorry if it makes confusing.
Quoted 5 lines
If you started with separate patches, it would be much better to pick the larger number, and add a note into the individual patch(es) stating the reason for the gap. Everything else is highly confusing. I would not be surprised if no one in the mfd world even looks at the mfd patch since it went back from v6 (?) to v3 according to its subject line.
I got it. Thanks for your guide.
Fortunately, the mfd maintainer has replied and applied the mfd patch (the previous separate one). And I see you added a Reviewed-by for the hwmon patch, so I assume I don't have to do anything more, is it?
I'll take care of the version number next time.
Thanks,
Yilun
Quoted 43 lines
Thanks,
GuenterQuoted 39 lines
Patch #1 implements the basic functions of the BMC chip for some Intel FPGA PCIe Acceleration Cards (PAC). The BMC is implemented using the Intel MAX 10 CPLD.
This BMC chip is connected to the FPGA by a SPI bus. To provide direct register access from the FPGA, the "SPI slave to Avalon Master Bridge" (spi-avmm) IP is integrated in the chip. It converts encoded streams of bytes from the host to the internal register read/write on the Avalon bus. So This driver uses the regmap-spi-avmm for register accessing.
Patch #2 adds support for the hwmon sub device in Intel MAX 10 BMC
Xu Yilun (2):
mfd: intel-m10-bmc: add Intel MAX 10 BMC chip support for Intel FPGA
PAC
hwmon: intel-m10-bmc-hwmon: add hwmon support for Intel MAX 10 BMC.../ABI/testing/sysfs-driver-intel-m10-bmc | 15 + Documentation/hwmon/index.rst | 1 + Documentation/hwmon/intel-m10-bmc-hwmon.rst | 78 +++++ drivers/hwmon/Kconfig | 11 + drivers/hwmon/Makefile | 1 + drivers/hwmon/intel-m10-bmc-hwmon.c | 334 +++++++++++++++++++++ drivers/mfd/Kconfig | 13 + drivers/mfd/Makefile | 2 + drivers/mfd/intel-m10-bmc.c | 164 ++++++++++ include/linux/mfd/intel-m10-bmc.h | 65 ++++ 10 files changed, 684 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-driver-intel-m10-bmc create mode 100644 Documentation/hwmon/intel-m10-bmc-hwmon.rst create mode 100644 drivers/hwmon/intel-m10-bmc-hwmon.c create mode 100644 drivers/mfd/intel-m10-bmc.c create mode 100644 include/linux/mfd/intel-m10-bmc.hSignature · 1 line
2.7.4
Guenter Roeck
maintainerQuoted 21 lines · Xu Yilun
Hi Guenter,
Quoted 12 lines · Guenter Roeck
Quoted 10 lines · Xu Yilun
I recently realized that maintainers may have trouble to apply patches to their trees if the patches depend on other being-reviewed patches. So I'm trying to wrapper the 2 patches into one patchset and let all the maintainers see the dependencies.
But the patch version is then not aligned between the 2 patches. I'm not sure how to handle it. I just picked the smaller number on Subject, but you could still see their own version changes in commit message of each patch. Sorry if it makes confusing.
Quoted 5 lines
If you started with separate patches, it would be much better to pick the larger number, and add a note into the individual patch(es) stating the reason for the gap. Everything else is highly confusing. I would not be surprised if no one in the mfd world even looks at the mfd patch since it went back from v6 (?) to v3 according to its subject line.
Quoted 6 lines
I got it. Thanks for your guide.
Fortunately, the mfd maintainer has replied and applied the mfd patch (the previous separate one). And I see you added a Reviewed-by for the hwmon patch, so I assume I don't have to do anything more, is it?
Thanks for letting me know. I applied the hwmon driver.
Thanks,
Guenter
Quoted 48 lines
I'll take care of the version number next time.
Thanks,
YilunQuoted 43 lines
Thanks,
GuenterQuoted 39 lines
Patch #1 implements the basic functions of the BMC chip for some Intel FPGA PCIe Acceleration Cards (PAC). The BMC is implemented using the Intel MAX 10 CPLD.
This BMC chip is connected to the FPGA by a SPI bus. To provide direct register access from the FPGA, the "SPI slave to Avalon Master Bridge" (spi-avmm) IP is integrated in the chip. It converts encoded streams of bytes from the host to the internal register read/write on the Avalon bus. So This driver uses the regmap-spi-avmm for register accessing.
Patch #2 adds support for the hwmon sub device in Intel MAX 10 BMC
Xu Yilun (2):
mfd: intel-m10-bmc: add Intel MAX 10 BMC chip support for Intel FPGA
PAC
hwmon: intel-m10-bmc-hwmon: add hwmon support for Intel MAX 10 BMC.../ABI/testing/sysfs-driver-intel-m10-bmc | 15 + Documentation/hwmon/index.rst | 1 + Documentation/hwmon/intel-m10-bmc-hwmon.rst | 78 +++++ drivers/hwmon/Kconfig | 11 + drivers/hwmon/Makefile | 1 + drivers/hwmon/intel-m10-bmc-hwmon.c | 334 +++++++++++++++++++++ drivers/mfd/Kconfig | 13 + drivers/mfd/Makefile | 2 + drivers/mfd/intel-m10-bmc.c | 164 ++++++++++ include/linux/mfd/intel-m10-bmc.h | 65 ++++ 10 files changed, 684 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-driver-intel-m10-bmc create mode 100644 Documentation/hwmon/intel-m10-bmc-hwmon.rst create mode 100644 drivers/hwmon/intel-m10-bmc-hwmon.c create mode 100644 drivers/mfd/intel-m10-bmc.c create mode 100644 include/linux/mfd/intel-m10-bmc.hSignature · 1 line
2.7.4