Skip to contentSkip to conversation

net: stmmac: Modify configuration method of EEE timers

PATCH Applied Voon Weifeng 2 participants 2 messages Oct 1, 2020 – Oct 3, 2020

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 net: stmmac: Modify configuration method of EEE timers

From: "Vineetha G. Jaya Kumaran" <[email protected]>

Ethtool manual stated that the tx-timer is the "the amount of time the device should stay in idle mode prior to asserting its Tx LPI". The previous implementation for "ethtool --set-eee tx-timer" sets the LPI TW timer duration which is not correct. Hence, this patch fixes the "ethtool --set-eee tx-timer" to configure the EEE LPI timer.

The LPI TW Timer will be using the defined default value instead of "ethtool --set-eee tx-timer" which follows the EEE LS timer implementation.

Fixes d765955d2ae0 ("stmmac: add the Energy Efficient Ethernet support")

Changelog V2
*Not removing/modifying the eee_timer.
*EEE LPI timer can be configured through ethtool and also the eee_timer module param.
*EEE TW Timer will be configured with default value only, not able to be configured through ethtool or module param. This follows the implementation of the EEE LS Timer.

---
 drivers/net/ethernet/stmicro/stmmac/stmmac.h  |  2 ++
 .../ethernet/stmicro/stmmac/stmmac_ethtool.c  | 12 +++++++++-
 .../net/ethernet/stmicro/stmmac/stmmac_main.c | 23 ++++++++++++-------
 3 files changed, 28 insertions(+), 9 deletions(-)
drivers/net/ethernet/stmicro/stmmac/stmmac.h +2 -0
index 9c02fc754bf1..545696971f65 100644
@@ -203,6 +203,8 @@ struct stmmac_priv {
 	int eee_enabled;
 	int eee_active;
 	int tx_lpi_timer;
+	int tx_lpi_enabled;
+	int eee_tw_timer;
 	unsigned int mode;
 	unsigned int chain_mode;
 	int extend_desc;
drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c +11 -1
index 430a4b32ec1e..814879f91f76 100644
@@ -665,6 +665,7 @@ static int stmmac_ethtool_op_get_eee(struct net_device *dev,
 	edata->eee_enabled = priv->eee_enabled;
 	edata->eee_active = priv->eee_active;
 	edata->tx_lpi_timer = priv->tx_lpi_timer;
+	edata->tx_lpi_enabled = priv->tx_lpi_enabled;
 
 	return phylink_ethtool_get_eee(priv->phylink, edata);
 }
@@ -678,6 +679,10 @@ static int stmmac_ethtool_op_set_eee(struct net_device *dev,
 	if (!priv->dma_cap.eee)
 		return -EOPNOTSUPP;
 
+	if (priv->tx_lpi_enabled != edata->tx_lpi_enabled)
+		netdev_warn(priv->dev,
+			    "Setting EEE tx-lpi is not supported\n");
+
 	if (!edata->eee_enabled)
 		stmmac_disable_eee_mode(priv);
 
@@ -685,7 +690,12 @@ static int stmmac_ethtool_op_set_eee(struct net_device *dev,
 	if (ret)
 		return ret;
 
-	priv->tx_lpi_timer = edata->tx_lpi_timer;
+	if (edata->eee_enabled &&
+	    priv->tx_lpi_timer != edata->tx_lpi_timer) {
+		priv->tx_lpi_timer = edata->tx_lpi_timer;
+		stmmac_eee_init(priv);
+	}
+
 	return 0;
 }
 
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +15 -8
index 89b2b3472852..b56b13d64ab4 100644
@@ -94,7 +94,7 @@ static const u32 default_msg_level = (NETIF_MSG_DRV | NETIF_MSG_PROBE |
 static int eee_timer = STMMAC_DEFAULT_LPI_TIMER;
 module_param(eee_timer, int, 0644);
 MODULE_PARM_DESC(eee_timer, "LPI tx expiration time in msec");
-#define STMMAC_LPI_T(x) (jiffies + msecs_to_jiffies(x))
+#define STMMAC_LPI_T(x) (jiffies + usecs_to_jiffies(x))
 
 /* By default the driver will use the ring mode to manage tx and rx descriptors,
  * but allow user to force to use the chain instead of the ring
@@ -370,7 +370,7 @@ static void stmmac_eee_ctrl_timer(struct timer_list *t)
 	struct stmmac_priv *priv = from_timer(priv, t, eee_ctrl_timer);
 
 	stmmac_enable_eee_mode(priv);
-	mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(eee_timer));
+	mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer));
 }
 
 /**
@@ -383,7 +383,7 @@ static void stmmac_eee_ctrl_timer(struct timer_list *t)
  */
 bool stmmac_eee_init(struct stmmac_priv *priv)
 {
-	int tx_lpi_timer = priv->tx_lpi_timer;
+	int eee_tw_timer = priv->eee_tw_timer;
 
 	/* Using PCS we cannot dial with the phy registers at this stage
 	 * so we do not support extra feature like EEE.
@@ -403,7 +403,7 @@ bool stmmac_eee_init(struct stmmac_priv *priv)
 		if (priv->eee_enabled) {
 			netdev_dbg(priv->dev, "disable EEE\n");
 			del_timer_sync(&priv->eee_ctrl_timer);
-			stmmac_set_eee_timer(priv, priv->hw, 0, tx_lpi_timer);
+			stmmac_set_eee_timer(priv, priv->hw, 0, eee_tw_timer);
 		}
 		mutex_unlock(&priv->lock);
 		return false;
@@ -411,11 +411,12 @@ bool stmmac_eee_init(struct stmmac_priv *priv)
 
 	if (priv->eee_active && !priv->eee_enabled) {
 		timer_setup(&priv->eee_ctrl_timer, stmmac_eee_ctrl_timer, 0);
-		mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(eee_timer));
 		stmmac_set_eee_timer(priv, priv->hw, STMMAC_DEFAULT_LIT_LS,
-				     tx_lpi_timer);
+				     eee_tw_timer);
 	}
 
+	mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer));
+
 	mutex_unlock(&priv->lock);
 	netdev_dbg(priv->dev, "Energy-Efficient Ethernet initialized\n");
 	return true;
@@ -930,6 +931,7 @@ static void stmmac_mac_link_down(struct phylink_config *config,
 
 	stmmac_mac_set(priv, priv->ioaddr, false);
 	priv->eee_active = false;
+	priv->tx_lpi_enabled = false;
 	stmmac_eee_init(priv);
 	stmmac_set_eee_pls(priv, priv->hw, false);
 }
@@ -1027,6 +1029,7 @@ static void stmmac_mac_link_up(struct phylink_config *config,
 	if (phy && priv->dma_cap.eee) {
 		priv->eee_active = phy_init_eee(phy, 1) >= 0;
 		priv->eee_enabled = stmmac_eee_init(priv);
+		priv->tx_lpi_enabled = priv->eee_enabled;
 		stmmac_set_eee_pls(priv, priv->hw, true);
 	}
 }
@@ -2061,7 +2064,7 @@ static int stmmac_tx_clean(struct stmmac_priv *priv, int budget, u32 queue)
 
 	if ((priv->eee_enabled) && (!priv->tx_path_in_lpi_mode)) {
 		stmmac_enable_eee_mode(priv);
-		mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(eee_timer));
+		mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer));
 	}
 
 	/* We still have pending packets, let's call for a new scheduling */
@@ -2694,7 +2697,11 @@ static int stmmac_hw_setup(struct net_device *dev, bool init_ptp)
 			netdev_warn(priv->dev, "PTP init failed\n");
 	}
 
-	priv->tx_lpi_timer = STMMAC_DEFAULT_TWT_LS;
+	priv->eee_tw_timer = STMMAC_DEFAULT_TWT_LS;
+
+	/* Convert the timer from msec to usec */
+	if (!priv->tx_lpi_timer)
+		priv->tx_lpi_timer = eee_timer * 1000;
 
 	if (priv->use_riwt) {
 		if (!priv->rx_riwt)
Signature · 1 line
2.17.1
maintainer Applied
#1 lore raw

From: Voon Weifeng <[email protected]>
Date: Thu, 1 Oct 2020 23:56:09 +0800

Quoted 15 lines

From: "Vineetha G. Jaya Kumaran" <[email protected]>

Ethtool manual stated that the tx-timer is the "the amount of time the device should stay in idle mode prior to asserting its Tx LPI". The previous implementation for "ethtool --set-eee tx-timer" sets the LPI TW timer duration which is not correct. Hence, this patch fixes the "ethtool --set-eee tx-timer" to configure the EEE LPI timer.

The LPI TW Timer will be using the defined default value instead of "ethtool --set-eee tx-timer" which follows the EEE LS timer implementation.

Fixes d765955d2ae0 ("stmmac: add the Energy Efficient Ethernet support")
Quoted 7 lines

Changelog V2
*Not removing/modifying the eee_timer.
*EEE LPI timer can be configured through ethtool and also the eee_timer module param.
*EEE TW Timer will be configured with default value only, not able to be configured through ethtool or module param. This follows the implementation of the EEE LS Timer.

Please put the Changelog above the various signoffs and other tags, as those should be at the end of the commit log message.

Just out of curiousity, where did you see put the changelog after the tags, and thus caused you to use this layout? If you decided that on your own, this is pretty much always a bad idea. Look to other patches which have been accepted as a guide for how to format your commit log message.

Applied, thank you.