Skip to contentSkip to conversation

net: fec: Fix phy_device lookup for phy_reset_after_clk_enable()

PATCH Applied Marek Vasut 2 participants 2 messages Oct 10, 2020 – Oct 12, 2020

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 net: fec: Fix phy_device lookup for phy_reset_after_clk_enable()

The phy_reset_after_clk_enable() is always called with ndev->phydev, however that pointer may be NULL even though the PHY device instance already exists and is sufficient to perform the PHY reset.

This condition happens in fec_open(), where the clock must be enabled first, then the PHY must be reset, and then the PHY IDs can be read out of the PHY.

If the PHY still is not bound to the MAC, but there is OF PHY node and a matching PHY device instance already, use the OF PHY node to obtain the PHY device instance, and then use that PHY device instance when triggering the PHY reset.

Fixes 1b0a83ac04e3 ("net: fec: add phy_reset_after_clk_enable() support")
Cc Christoph Niedermaier <[email protected]>
Cc David S. Miller <[email protected]>
Cc NXP Linux Team <[email protected]>
Cc Richard Leitner <[email protected]>
Cc Shawn Guo <[email protected]>

---
V2: - put_device() the phy_dev reference from of_phy_find_device()
- Add additional explanation into the commit message

---
 drivers/net/ethernet/freescale/fec_main.c | 25 +++++++++++++++++++++--
 1 file changed, 23 insertions(+), 2 deletions(-)
drivers/net/ethernet/freescale/fec_main.c +23 -2
index 2d5433301843..8f7eca1e7716 100644
@@ -1912,6 +1912,27 @@ static int fec_enet_mdio_write(struct mii_bus *bus, int mii_id, int regnum,
 	return ret;
 }
 
+static void fec_enet_phy_reset_after_clk_enable(struct net_device *ndev)
+{
+	struct fec_enet_private *fep = netdev_priv(ndev);
+	struct phy_device *phy_dev = ndev->phydev;
+
+	if (phy_dev) {
+		phy_reset_after_clk_enable(phy_dev);
+	} else if (fep->phy_node) {
+		/*
+		 * If the PHY still is not bound to the MAC, but there is
+		 * OF PHY node and a matching PHY device instance already,
+		 * use the OF PHY node to obtain the PHY device instance,
+		 * and then use that PHY device instance when triggering
+		 * the PHY reset.
+		 */
+		phy_dev = of_phy_find_device(fep->phy_node);
+		phy_reset_after_clk_enable(phy_dev);
+		put_device(&phy_dev->mdio.dev);
+	}
+}
+
 static int fec_enet_clk_enable(struct net_device *ndev, bool enable)
 {
 	struct fec_enet_private *fep = netdev_priv(ndev);
@@ -1938,7 +1959,7 @@ static int fec_enet_clk_enable(struct net_device *ndev, bool enable)
 		if (ret)
 			goto failed_clk_ref;
 
-		phy_reset_after_clk_enable(ndev->phydev);
+		fec_enet_phy_reset_after_clk_enable(ndev);
 	} else {
 		clk_disable_unprepare(fep->clk_enet_out);
 		if (fep->clk_ptp) {
@@ -2987,7 +3008,7 @@ fec_enet_open(struct net_device *ndev)
 	 * phy_reset_after_clk_enable() before because the PHY wasn't probed.
 	 */
 	if (reset_again)
-		phy_reset_after_clk_enable(ndev->phydev);
+		fec_enet_phy_reset_after_clk_enable(ndev);
 
 	/* Probe and connect to PHY when open the interface */
 	ret = fec_enet_mii_probe(ndev);
Signature · 1 line
2.28.0
maintainer Applied
#1 lore raw
Quoted 13 lines · On Sat, 10 Oct 2020 11:10:00 +0200 Marek Vasut wrote:

The phy_reset_after_clk_enable() is always called with ndev->phydev, however that pointer may be NULL even though the PHY device instance already exists and is sufficient to perform the PHY reset.

This condition happens in fec_open(), where the clock must be enabled first, then the PHY must be reset, and then the PHY IDs can be read out of the PHY.

If the PHY still is not bound to the MAC, but there is OF PHY node and a matching PHY device instance already, use the OF PHY node to obtain the PHY device instance, and then use that PHY device instance when triggering the PHY reset.

Quoted 7 lines
Fixes 1b0a83ac04e3 ("net: fec: add phy_reset_after_clk_enable() support")
Cc Christoph Niedermaier <[email protected]>
Cc David S. Miller <[email protected]>
Cc NXP Linux Team <[email protected]>
Cc Richard Leitner <[email protected]>
Cc Shawn Guo <[email protected]>

Applied.