target/arm: Various v8.1M minor features
Subsystems (7)
cover target/arm: Various v8.1M minor features
This patchseries implements various minor v8.1M new features, notably the branch-future and low-overhead-loop extensions.
(None of this will get enabled until we have enough to implement a CPU model which has v8.1M, which will be the Cortex-M55, but as usual we can get stuff into the tree gradually.)
Patch 1 is a decodetree fix suggested by Richard that is necessary to avoid wrong-decode of the changes to t32.decode by later patches.
thanks
-- PMM
Peter Maydell (10):
decodetree: Fix codegen for non-overlapping group inside overlapping
group
target/arm: Implement v8.1M NOCP handling
target/arm: Implement v8.1M conditional-select insns target/arm: Make the t32 insn[25:23]=111 group non-overlapping target/arm: Don't allow BLX imm for M-profile
target/arm: Implement v8.1M branch-future insns (as NOPs) target/arm: Implement v8.1M low-overhead-loop instructions target/arm: Fix has_vfp/has_neon ID reg squashing for M-profile target/arm: Implement FPSCR.LTPSIZE for M-profile LOB extension target/arm: Fix writing to FPSCR.FZ16 on M-profile
target/arm/cpu.h | 7 ++ target/arm/m-nocp.decode | 10 ++- target/arm/t32.decode | 50 +++++++---- target/arm/cpu.c | 34 ++++--- target/arm/translate.c | 157 +++++++++++++++++++++++++++++++++ target/arm/vfp_helper.c | 30 +++++-- scripts/decodetree.py | 2 +- target/arm/translate-vfp.c.inc | 17 +++- 8 files changed, 268 insertions(+), 39 deletions(-)
Signature · 1 line
2.20.1
PATCH 1/1 Deprecate TileGX port
Deprecate our TileGX target support:
* we have no active maintainer for it
* it has had essentially no contributions (other than tree-wide cleanups and similar) since it was first added
* the Linux kernel dropped support in 2018, as has glibc
Note the deprecation in the manual, but don't try to print a warning when QEMU runs -- printing unsuppressable messages is more obtrusive for linux-user mode than it would be for system-emulation mode, and it doesn't seem worth trying to invent a new suppressible-error system for linux-user just for this.
---
We discussed dropping this target last year:
https://patchew.org/QEMU/[email protected]/
and before that in 2018, when Chen told us he didn't have time to work on tilegx any more:
https://lists.gnu.org/archive/html/qemu-devel/2018-03/msg03955.html
Given that tilegx is no longer in upstream Linux I think it makes sense to finally deprecate-and-drop our linux-user support for it.
docs/system/deprecated.rst | 11 +++++++++++ 1 file changed, 11 insertions(+)
docs/system/deprecated.rst +11 -0
@@ -387,6 +387,17 @@ The above, converted to the current supported format:: json:{"file.driver":"rbd", "file.pool":"rbd", "file.image":"name"} +linux-user mode CPUs +-------------------- + +``tilegx`` CPUs (since 5.1.0) +''''''''''''''''''''''''''''' + +The ``tilegx`` guest CPU support (which was only implemented in +linux-user mode) is deprecated and will be removed in a future version +of QEMU. Support for this CPU was removed from the upstream Linux +kernel in 2018, and has also been dropped from glibc. + Related binaries ----------------
Signature · 1 line
2.20.1
Re: [PATCH] Deprecate TileGX port
Quoted 30 lines · Peter Maydell
Deprecate our TileGX target support:
* we have no active maintainer for it
* it has had essentially no contributions (other than tree-wide cleanups and similar) since it was first added
* the Linux kernel dropped support in 2018, as has glibcNote the deprecation in the manual, but don't try to print a warning when QEMU runs -- printing unsuppressable messages is more obtrusive for linux-user mode than it would be for system-emulation mode, and it doesn't seem worth trying to invent a new suppressible-error system for linux-user just for this.
Signed-off-by Peter Maydell <[email protected]>---
We discussed dropping this target last year:
https://patchew.org/QEMU/[email protected]/
and before that in 2018, when Chen told us he didn't have time to work on tilegx any more:
https://lists.gnu.org/archive/html/qemu-devel/2018-03/msg03955.html
Given that tilegx is no longer in upstream Linux I think it makes sense to finally deprecate-and-drop our linux-user support for it.
docs/system/deprecated.rst| 11 +++++++++++1 file changed, 11 insertions(+)docs/system/deprecated.rst +0
-0
docs/system/deprecated.rst The above, converted to the current supported format:: · line 394
Quoted 8 lines
docs/system/deprecated.rst +5
-0@@ -387,6 +387,17 @@ The above, converted to the current supported format:: json:{"file.driver":"rbd", "file.pool":"rbd", "file.image":"name"} +linux-user mode CPUs +-------------------- + +``tilegx`` CPUs (since 5.1.0) +'''''''''''''''''''''''''''''
Is that 5.2?
Regards,
BALATON Zoltan
Quoted 10 lines
docs/system/deprecated.rst +6
-0+ +The ``tilegx`` guest CPU support (which was only implemented in +linux-user mode) is deprecated and will be removed in a future version +of QEMU. Support for this CPU was removed from the upstream Linux +kernel in 2018, and has also been dropped from glibc. +Related binaries
----------------
Re: [PATCH] Deprecate TileGX port
Quoted 4 lines · BALATON Zoltan
Quoted 1 line · Peter Maydell
Deprecate our TileGX target support:
Is that 5.2?
This mail was patch of an accidental mailbomb of the list with a couple of dozen stale (already sent weeks/months back) patches that were hanging around in a directory that I ran 'git send-email *.patch' on by mistake. Please ignore it, and sorry for the confusion :-(
thanks
-- PMM
PATCH 1/1 Deprecate Unicore32 port
In reply to Peter MaydellDeprecate our Unicore32 target support:
* the Linux kernel dropped support for unicore32 in commit 05119217a9bd199c for its 5.9 release (with rationale in the cover letter: https://lkml.org/lkml/2020/8/3/232 )
* there is apparently no upstream toolchain that can create unicore32 binaries
* the maintainer doesn't seem to have made any contributions to QEMU since the port first landed in 2012
* nobody else seems to have made changes to the unicore code except for generic cleanups either
---
We last considered this back in 2018, but in the end both QEMU and the kernel gave the port a stay of execution; the maintenance situation doesn't seem to have improved, and now the kernel has dropped support and especially given the lack of a toolchain I think it's time to start the deprecation process here.
--- docs/system/deprecated.rst | 8 ++++++++ 1 file changed, 8 insertions(+)
docs/system/deprecated.rst +8 -0
@@ -416,6 +416,14 @@ The above, converted to the current supported format:: linux-user mode CPUs -------------------- +``unicore32`` CPUs (since 5.2.0) +'''''''''''''''''''''''''''''''' + +The ``unicore32`` guest CPU support is deprecated and will be removed in +a future version of QEMU. Support for this CPU was removed from the +upstream Linux kernel, and there is no available upstream toolchain +to build binaries for it. + ``tilegx`` CPUs (since 5.1.0) '''''''''''''''''''''''''''''
Signature · 1 line
2.20.1
PATCH 1/1 arm.risu, thumb.risu: Add v8.2 DP and FHM insns
In reply to Peter MaydellAdd coverage for the v8.2 DP and v8.2 FHM insns in the Neon extension space. (We already had the v8.1 VQRDMLAH/VQRDLSH and the v8.3 VCADD/VCMLA, so this brings the risu coverage into line with what QEMU has implemented so far.)
---
I added these patterns as part of testing for the first part of the Neon decodetree conversion and forgot I'd never sent out the risu patch for review.
arm.risu | 18 ++++++++++++++++++ thumb.risu | 18 ++++++++++++++++++ 2 files changed, 36 insertions(+)
arm.risu +18 -0
@@ -861,6 +861,24 @@ VQRDMLAH_s A1 1111001 q:1 1 d:1 size:2 vn:4 vd:4 1110 n:1 1 m:1 0 vm:4 VQRDMLSH A1 111100110 d:1 size:2 vn:4 vd:4 1100 n:1 q:1 m:1 1 vm:4 VQRDMLSH_s A1 1111001 q:1 1 d:1 size:2 vn:4 vd:4 1111 n:1 1 m:1 0 vm:4 +# +# ARMv8.2 extensions +# +@v8_2_dp + +VUDOT A1 1111110 00 d:1 10 vn:4 vd:4 1101 n:1 q:1 m:1 1 vm:4 +VSDOT A1 1111110 00 d:1 10 vn:4 vd:4 1101 n:1 q:1 m:1 0 vm:4 + +VUDOT_s A1 11111110 0 d:1 10 vn:4 vd:4 1101 n:1 q:1 m:1 1 vm:4 +VSDOT_s A1 11111110 0 d:1 10 vn:4 vd:4 1101 n:1 q:1 m:1 0 vm:4 + +@v8_2_fhm + +VFMAL A1 1111110 00 d:1 10 vn:4 vd:4 1000 n:1 q:1 m:1 1 vm:4 +VFMSL A1 1111110 01 d:1 10 vn:4 vd:4 1000 n:1 q:1 m:1 1 vm:4 +VFMAL_s A1 11111110 0 d:1 00 vn:4 vd:4 1000 n:1 q:1 m:1 1 vm:4 +VFMSL_s A1 11111110 1 d:1 00 vn:4 vd:4 1000 n:1 q:1 m:1 1 vm:4 + # # ARMv8.3 extensions #
thumb.risu +18 -0
@@ -449,6 +449,24 @@ VQRDMLAH_s T1 111 q:1 11111 d:1 size:2 vn:4 vd:4 1110 n:1 1 m:1 0 vm:4 VQRDMLSH T1 111111110 d:1 size:2 vn:4 vd:4 1100 n:1 q:1 m:1 1 vm:4 VQRDMLSH_s T1 111 q:1 11111 d:1 size:2 vn:4 vd:4 1111 n:1 1 m:1 0 vm:4 +# +# ARMv8.2 extensions +# +@v8_2_dp + +VUDOT A1 1111110 00 d:1 10 vn:4 vd:4 1101 n:1 q:1 m:1 1 vm:4 +VSDOT A1 1111110 00 d:1 10 vn:4 vd:4 1101 n:1 q:1 m:1 0 vm:4 + +VUDOT_s A1 11111110 0 d:1 10 vn:4 vd:4 1101 n:1 q:1 m:1 1 vm:4 +VSDOT_s A1 11111110 0 d:1 10 vn:4 vd:4 1101 n:1 q:1 m:1 0 vm:4 + +@v8_2_fhm + +VFMAL A1 1111110 00 d:1 10 vn:4 vd:4 1000 n:1 q:1 m:1 1 vm:4 +VFMSL A1 1111110 01 d:1 10 vn:4 vd:4 1000 n:1 q:1 m:1 1 vm:4 +VFMAL_s A1 11111110 0 d:1 00 vn:4 vd:4 1000 n:1 q:1 m:1 1 vm:4 +VFMSL_s A1 11111110 1 d:1 00 vn:4 vd:4 1000 n:1 q:1 m:1 1 vm:4 + # # ARMv8.3 extensions #
Signature · 1 line
2.20.1
PATCH 1/1 Makefile: Remove config-devices.mak on "make clean"
In reply to Peter MaydellThe config-devices.mak files are generated by "make", and so they should be deleted by "make clean".
(This is different from config-host.mak and config-all-disas.mak, which are created by "configure" and so only deleted by "make distclen".)
If we don't delete these files on "make clean", then the build tree is left in a state where it has the config-devices.mak file but not the config-devices.mak.d file, and make will not realize that it needs to rebuild config-devices.mak if, for instance, hw/sd/Kconfig changes.
NB: config-all-devices.mak is also generated by "make", but we already remove it on "make clean".
---
I didn't remove the existing 'rm -f $(SUBDIR_DEVICES_MAK)' from the 'distclean' rules on the basis that config-all-devices.mak is explicitly removed in both 'distclean' and 'clean', despite 'distclean' depending on 'clean'...
--- Makefile | 1 + 1 file changed, 1 insertion(+)
Makefile +1 -0
@@ -775,6 +775,7 @@ clean: recurse-clean rm -f storage-daemon/qapi/qapi-gen-timestamp rm -rf qga/qapi-generated rm -f config-all-devices.mak + rm -f $(SUBDIR_DEVICES_MAK) VERSION ?= $(shell cat VERSION)
Signature · 1 line
2.20.1
PATCH 1/1 Deprecate lm32 port
In reply to Peter MaydellDeprecate our lm32 target support. Michael Walle (former lm32 maintainer) suggested that we do this in 2019:
https://www.mail-archive.com/[email protected]/msg605024.html
because the only public user of the architecture is the many-years-dead milkymist project. (The Linux port to lm32 was never merged upstream.)
In commit 4b4d96c776f552e (March 2020) we marked it as 'orphan' in the MAINTAINERS file, but didn't officially deprecate it. Mark it deprecated now, with the intention of removing it from QEMU in mid-2021 before the 6.1 release.
---
Based-on: [email protected] ("Deprecate Unicore32 port") to avoid the obvious textual-conflict.
docs/system/deprecated.rst | 8 ++++++++ 1 file changed, 8 insertions(+)
docs/system/deprecated.rst +8 -0
@@ -416,6 +416,14 @@ The above, converted to the current supported format:: linux-user mode CPUs -------------------- +``lm32`` CPUs (since 5.2.0) +''''''''''''''''''''''''''' + +The ``lm32`` guest CPU support is deprecated and will be removed in +a future version of QEMU. The only public user of this architecture +was the milkymist project, which has been dead for years; there was +never an upstream Linux port. + ``unicore32`` CPUs (since 5.2.0) ''''''''''''''''''''''''''''''''
Signature · 1 line
2.20.1
PATCH 1/1 arm.risu: Add patterns for fp16 insns
In reply to Peter MaydellAdd patterns for the fp16 half-precision floating point extension. Where older pre-fp16 patterns used to include UNDEF encodings that now mean fp16, constrain them so that tests generated from those patterns will give the same results on CPUs both with and without fp16.
---
This is what I've been testing my fp16 support patchset with. NB that if you have pre-built golden-reference files for the old patterns that wanted to see UNDEFs for fp16 insns you'll need to regenerate those at some point when the fp16 support lands for -cpu max.
arm.risu | 218 +++++++++++++++++++++++++++++++++++++++++++------------ 1 file changed, 170 insertions(+), 48 deletions(-)
arm.risu +170 -48
@@ -456,6 +456,9 @@ VLDST_UNDEF A1c 1111 0100 1 x 0 0 any:8 11 any2:10 # space (table A7-9 in DDI0406B) # We include UNDEF combinations here; there are no # UNPREDICTABLE encodings we need to avoid. +# We avoid size encodings that are fp16 under the v8.2-FP16 extension: +# sz=1 for the float insns which have a 1-bit size field in bit 20, +# and instead hard-wire that bit to 0. ########################################################### VHADD A1 1111 001 u 0 d sz:2 vn:4 vd:4 0000 n q m 0 vm:4
@@ -471,9 +474,9 @@ VORN A1 1111 0010 0 d 11 vn:4 vd:4 0001 n q m 1 vm:4 VEOR_VBIT A1 1111 0011 0 d op:2 vn:4 vd:4 0001 n q m 1 vm:4 VQSUB A1 1111 001 u 0 d sz:2 vn:4 vd:4 0010 n q m 1 vm:4 VCGT A1 1111 001 u 0 d sz:2 vn:4 vd:4 0011 n q m 0 vm:4 -VCGT A2 1111 0011 0 d 1 sz vn:4 vd:4 1110 n q m 0 vm:4 +VCGT A2 1111 0011 0 d 1 0 vn:4 vd:4 1110 n q m 0 vm:4 VCGE A1 1111 001 u 0 d sz:2 vn:4 vd:4 0011 n q m 1 vm:4 -VCGE A2 1111 0011 0 d 0 sz vn:4 vd:4 1110 n q m 0 vm:4 +VCGE A2 1111 0011 0 d 0 0 vn:4 vd:4 1110 n q m 0 vm:4 VSHL A1 1111 001 u 0 d sz:2 vn:4 vd:4 0100 n q m 0 vm:4 VQSHL A1 1111 001 u 0 d sz:2 vn:4 vd:4 0100 n q m 1 vm:4 VRSHL A1 1111 001 u 0 d sz:2 vn:4 vd:4 0101 n q m 0 vm:4
@@ -486,7 +489,7 @@ VADD A1 1111 0010 0 d sz:2 vn:4 vd:4 1000 n q m 0 vm:4 VSUB A1 1111 0011 0 d sz:2 vn:4 vd:4 1000 n q m 0 vm:4 VTST A1 1111 0010 0 d sz:2 vn:4 vd:4 1000 n q m 1 vm:4 VCEQ A1 1111 0011 0 d sz:2 vn:4 vd:4 1000 n q m 1 vm:4 -VCEQ A2 1111 0010 0 d 0 sz vn:4 vd:4 1110 n q m 0 vm:4 +VCEQ A2 1111 0010 0 d 0 0 vn:4 vd:4 1110 n q m 0 vm:4 VMLA A1 1111 001 op 0 d sz:2 vn:4 vd:4 1001 n q m 0 vm:4 VMUL A1 1111 001 op 0 d sz:2 vn:4 vd:4 1001 n q m 1 vm:4 VPMAX A1 1111 001 u 0 d sz:2 vn:4 vd:4 1010 n q m 0 vm:4
@@ -495,22 +498,22 @@ VQDMULH A1 1111 0010 0 d sz:2 vn:4 vd:4 1011 n q m 0 vm:4 VQRDMULH A1 1111 0011 0 d sz:2 vn:4 vd:4 1011 n q m 0 vm:4 VPADD A1 1111 0010 0 d sz:2 vn:4 vd:4 1011 n q m 1 vm:4 # NB: VFM is VFPv4 only. There is no Neon encoding for VFNM. -VFM A1 1111 0010 0 d op sz vn:4 vd:4 1100 n q m 1 vm:4 -VADD_float A1 1111 0010 0 d 0 sz vn:4 vd:4 1101 n q m 0 vm:4 -VSUB_float A1 1111 0010 0 d 1 sz vn:4 vd:4 1101 n q m 0 vm:4 -VPADD_float A1 1111 0011 0 d 0 sz vn:4 vd:4 1101 n q m 0 vm:4 -VABD_float A1 1111 0011 0 d 1 sz vn:4 vd:4 1101 n q m 0 vm:4 -VMLA_float A1 1111 0010 0 d 0 sz vn:4 vd:4 1101 n q m 1 vm:4 -VMLS_float A1 1111 0010 0 d 1 sz vn:4 vd:4 1101 n q m 1 vm:4 -VMUL_float A1 1111 0011 0 d 0 sz vn:4 vd:4 1101 n q m 1 vm:4 -VACGE A1 1111 0011 0 d 0 sz vn:4 vd:4 1110 n q m 1 vm:4 -VACGT A1 1111 0011 0 d 1 sz vn:4 vd:4 1110 n q m 1 vm:4 -VMAX_float A1 1111 0010 0 d 0 sz vn:4 vd:4 1111 n q m 0 vm:4 -VMIN_float A1 1111 0010 0 d 1 sz vn:4 vd:4 1111 n q m 0 vm:4 -VPMAX_float A1 1111 0011 0 d 0 sz vn:4 vd:4 1111 n q m 0 vm:4 -VPMIN_float A1 1111 0011 0 d 1 sz vn:4 vd:4 1111 n q m 0 vm:4 -VRECPS A1 1111 0010 0 d 0 sz vn:4 vd:4 1111 n q m 1 vm:4 -VRSQRTS A1 1111 0010 0 d 1 sz vn:4 vd:4 1111 n q m 1 vm:4 +VFM A1 1111 0010 0 d op 0 vn:4 vd:4 1100 n q m 1 vm:4 +VADD_float A1 1111 0010 0 d 0 0 vn:4 vd:4 1101 n q m 0 vm:4 +VSUB_float A1 1111 0010 0 d 1 0 vn:4 vd:4 1101 n q m 0 vm:4 +VPADD_float A1 1111 0011 0 d 0 0 vn:4 vd:4 1101 n q m 0 vm:4 +VABD_float A1 1111 0011 0 d 1 0 vn:4 vd:4 1101 n q m 0 vm:4 +VMLA_float A1 1111 0010 0 d 0 0 vn:4 vd:4 1101 n q m 1 vm:4 +VMLS_float A1 1111 0010 0 d 1 0 vn:4 vd:4 1101 n q m 1 vm:4 +VMUL_float A1 1111 0011 0 d 0 0 vn:4 vd:4 1101 n q m 1 vm:4 +VACGE A1 1111 0011 0 d 0 0 vn:4 vd:4 1110 n q m 1 vm:4 +VACGT A1 1111 0011 0 d 1 0 vn:4 vd:4 1110 n q m 1 vm:4 +VMAX_float A1 1111 0010 0 d 0 0 vn:4 vd:4 1111 n q m 0 vm:4 +VMIN_float A1 1111 0010 0 d 1 0 vn:4 vd:4 1111 n q m 0 vm:4 +VPMAX_float A1 1111 0011 0 d 0 0 vn:4 vd:4 1111 n q m 0 vm:4 +VPMIN_float A1 1111 0011 0 d 1 0 vn:4 vd:4 1111 n q m 0 vm:4 +VRECPS A1 1111 0010 0 d 0 0 vn:4 vd:4 1111 n q m 1 vm:4 +VRSQRTS A1 1111 0010 0 d 1 0 vn:4 vd:4 1111 n q m 1 vm:4 ########### Neon 1 reg + modified immediate ############### # Instructions from the Neon "1 reg + modified immediate"
@@ -577,15 +580,19 @@ VQDMULL A1 1111 0010 1 d sz:2 vn:4 vd:4 1101 n 0 m 0 vm:4 { $sz != 3; } # (table A7-11 in DDI0406B) # UNDEF cases included. # sz = 11 is in vext/vtbl/vtbx/vdup/2reg-misc space. +# We avoid f=1 sz=01 which is v8.2-FP16 ########################################################### # includes float variants -VMLA_scalar A1 1111 001 q 1 d sz:2 vn:4 vd:4 0 0 0 f n 1 m 0 vm:4 { $sz != 3; } -VMLS_scalar A1 1111 001 q 1 d sz:2 vn:4 vd:4 0 1 0 f n 1 m 0 vm:4 { $sz != 3; } +VMLA_scalar A1 1111 001 q 1 d sz:2 vn:4 vd:4 0 0 0 f n 1 m 0 vm:4 \ + { $sz != 3 && ($f == 0 || $sz != 1); } +VMLS_scalar A1 1111 001 q 1 d sz:2 vn:4 vd:4 0 1 0 f n 1 m 0 vm:4 \ + { $sz != 3 && ($f == 0 || $sz != 1); } VMLAL_scalar A2 1111 001 u 1 d sz:2 vn:4 vd:4 0 0 1 0 n 1 m 0 vm:4 { $sz != 3; } VMLSL_scalar A2 1111 001 u 1 d sz:2 vn:4 vd:4 0 1 1 0 n 1 m 0 vm:4 { $sz != 3; } VQDMLAL_scalar A2 1111 0010 1 d sz:2 vn:4 vd:4 0 0 11 n 1 m 0 vm:4 { $sz != 3; } VQDMLSL_scalar A2 1111 0010 1 d sz:2 vn:4 vd:4 0 1 11 n 1 m 0 vm:4 { $sz != 3; } -VMUL_scalar A1 1111 001 q 1 d sz:2 vn:4 vd:4 100 f n 1 m 0 vm:4 { $sz != 3; } +VMUL_scalar A1 1111 001 q 1 d sz:2 vn:4 vd:4 100 f n 1 m 0 vm:4 \ + { $sz != 3 && ($f == 0 || $sz != 1); } VMULL_scalar A2 1111 001 u 1 d sz:2 vn:4 vd:4 1010 n 1 m 0 vm:4 { $sz != 3; } VQDMULL_scalar A2 1111 0010 1 d sz:2 vn:4 vd:4 1011 n 1 m 0 vm:4 { $sz != 3; } VQDMULH_scalar A2 1111 001 q 1 d sz:2 vn:4 vd:4 1100 n 1 m 0 vm:4 { $sz != 3; }
@@ -595,6 +602,7 @@ VQRDMULH_scalar A2 1111 001 q 1 d sz:2 vn:4 vd:4 1101 n 1 m 0 vm:4 { $sz != 3; } # Instructions from the Neon "2 regs miscellaneous" space # (table A7-13 in DDI0406B) # UNDEF cases included. +# We avoid f=1 sz=01 which is v8.2-FP16 ########################################################### VREV A1 1111 0011 1 d 11 sz:2 00 vd:4 000 op:2 q m 0 vm:4 VPADDL A1 1111 0011 1 d 11 sz:2 00 vd:4 0010 op q m 0 vm:4
@@ -605,13 +613,13 @@ VMVN A1 1111 0011 1 d 11 sz:2 00 vd:4 0 1011 q m 0 vm:4 VPADAL A1 1111 0011 1 d 11 sz:2 00 vd:4 0110 op q m 0 vm:4 VQABS A1 1111 0011 1 d 11 sz:2 00 vd:4 0111 0 q m 0 vm:4 VQNEG A1 1111 0011 1 d 11 sz:2 00 vd:4 0111 1 q m 0 vm:4 -VCGT0 A1 1111 0011 1 d 11 sz:2 01 vd:4 0 f 000 q m 0 vm:4 -VCGE0 A1 1111 0011 1 d 11 sz:2 01 vd:4 0 f 001 q m 0 vm:4 -VCEQ0 A1 1111 0011 1 d 11 sz:2 01 vd:4 0 f 010 q m 0 vm:4 -VCLE0 A1 1111 0011 1 d 11 sz:2 01 vd:4 0 f 011 q m 0 vm:4 -VCLT0 A1 1111 0011 1 d 11 sz:2 01 vd:4 0 f 100 q m 0 vm:4 -VABS A1 1111 0011 1 d 11 sz:2 01 vd:4 0 f 110 q m 0 vm:4 -VNEG A1 1111 0011 1 d 11 sz:2 01 vd:4 0 f 111 q m 0 vm:4 +VCGT0 A1 1111 0011 1 d 11 sz:2 01 vd:4 0 f 000 q m 0 vm:4 { $f == 0 || $sz != 1; } +VCGE0 A1 1111 0011 1 d 11 sz:2 01 vd:4 0 f 001 q m 0 vm:4 { $f == 0 || $sz != 1; } +VCEQ0 A1 1111 0011 1 d 11 sz:2 01 vd:4 0 f 010 q m 0 vm:4 { $f == 0 || $sz != 1; } +VCLE0 A1 1111 0011 1 d 11 sz:2 01 vd:4 0 f 011 q m 0 vm:4 { $f == 0 || $sz != 1; } +VCLT0 A1 1111 0011 1 d 11 sz:2 01 vd:4 0 f 100 q m 0 vm:4 { $f == 0 || $sz != 1; } +VABS A1 1111 0011 1 d 11 sz:2 01 vd:4 0 f 110 q m 0 vm:4 { $f == 0 || $sz != 1; } +VNEG A1 1111 0011 1 d 11 sz:2 01 vd:4 0 f 111 q m 0 vm:4 { $f == 0 || $sz != 1; } VSWP A1 1111 0011 1 d 11 sz:2 10 vd:4 00000 q m 0 vm:4 # d == m gives UNKNOWN results, so avoid it VTRN A1 1111 0011 1 d 11 sz:2 10 vd:4 00001 q m 0 vm:4 { ($d != $m) || ($vd != $vm); }
@@ -624,10 +632,10 @@ VSHLL A2 1111 0011 1 d 11 sz:2 10 vd:4 0011 0 0 m 0 vm:4 # float-halfprec (A8.6.299) # NB that half-precision needs at least an A9; A8 doesn't have it VCVT_half A1 1111 0011 1 d 11 sz:2 10 vd:4 011 op 0 0 m 0 vm:4 -VRECPE A1 1111 0011 1 d 11 sz:2 11 vd:4 010 f 0 q m 0 vm:4 -VRSQRTE A1 1111 0011 1 d 11 sz:2 11 vd:4 010 f 1 q m 0 vm:4 -# float to int, neon versions (A8.6.294) -VCVT_neon A1 1111 0011 1 d 11 sz:2 11 vd:4 0 11 op:2 q m 0 vm:4 +VRECPE A1 1111 0011 1 d 11 sz:2 11 vd:4 010 f 0 q m 0 vm:4 { $f == 0 || $sz != 1; } +VRSQRTE A1 1111 0011 1 d 11 sz:2 11 vd:4 010 f 1 q m 0 vm:4 { $f == 0 || $sz != 1; } +# float to int, neon versions (A8.6.294); avoid sz=01 which is FP16 +VCVT_neon A1 1111 0011 1 d 11 sz:2 11 vd:4 0 11 op:2 q m 0 vm:4 { $sz != 1; } ########### Neon other #################################### # Instructions which have their own entry in the top level
@@ -649,6 +657,8 @@ VDUP_scalar A1 1111 0011 1 d 11 imm:4 vd:4 11000 q m 0 vm:4 # "VFP data-processing instructions" space # as described in DDI0406B table A7-16 and the subtables # it refers to. +# These don't include fp16, which has [11:9] 0b100 +# (described in the Arm ARM as [11:9] 0b10 and a 2-bit size field) ########################################################### # VMLA, VMLS
@@ -752,7 +762,7 @@ VLDM A2b cond:4 110 p 0 d w 1 rn:4 vd:4 1010 00 imm:6 \ # UNDEF cases for both A1 and A2: P==U && W==1 VLDM A1c cond:4 110 p u d 1 1 rn:4 vd:4 101 x imm:8 !constraints { $p == $u; } -# VSTR +# VSTR (no overlap with VSTR_f16) # both A1 and A2 encodings, U = 1 VSTR A1a cond:4 1101 1 d 00 rn:4 vd:4 101 x imm:8 \ !memory { reg_plus_imm($rn, $imm * 4); }
@@ -760,7 +770,7 @@ VSTR A1a cond:4 1101 1 d 00 rn:4 vd:4 101 x imm:8 \ VSTR A1b cond:4 1101 0 d 00 rn:4 vd:4 101 x imm:8 \ !memory { reg_minus_imm($rn, $imm * 4); } -# VLDR +# VLDR (no overlap with VLDR_f16) # both A1 and A2 encodings, U = 1 VLDR A1a cond:4 1101 1 d 01 rn:4 vd:4 101 x imm:8 \ !memory { reg_plus_imm($rn, $imm * 4); }
@@ -799,9 +809,9 @@ VMOV_core_double A1 cond:4 1100 010 op:1 rt2:4 rt:4 1011 00 m:1 1 vm:4 { $op == # VSEL VSEL A1 1111 11100 d cc:2 vn:4 vd:4 101 sz n 0 m 0 vm:4 # VMINNM and VMAXNM -# neon -VMINMAXNM A1 1111 00110 d op sz vn:4 vd:4 1111 n q m 1 vm:4 -# vfp +# neon: sz=0 (avoiding sz=1 which is FP16) +VMINMAXNM A1 1111 00110 d op 0 vn:4 vd:4 1111 n q m 1 vm:4 +# vfp (does not overlap with FP16) VMINMAXNM A2 1111 11101 d 00 vn:4 vd:4 101 sz n op m 0 vm:4 # Crypto
@@ -842,8 +852,8 @@ VCVT_rm A1 1111 11101 d 1111 rm:2 vd:4 101 sz op 1 m 0 vm:4 # 64<->16 conversions (see also pattern earlier which is the sz==0 case) VCVT_B_TT_64 A1 cond:4 1110 1 d 11 001 op vd:4 101 1 t 1 m 0 vm:4 -# VCVT with rounding mode specified, neon -VCVT_rm_neon A1 1111 00111 d 11 size:2 11 vd:4 00 rm:2 op q m 0 vm:4 +# VCVT with rounding mode specified, neon; avoid sz=0b01 which is FP16 +VCVT_rm_neon A1 1111 00111 d 11 size:2 11 vd:4 00 rm:2 op q m 0 vm:4 { $size != 1; } # CRC # Note that sz == 0b11 is UNPREDICTABLE (either UNDEF, NOP or as if == 0b10)
@@ -879,16 +889,128 @@ VFMSL A1 1111110 01 d:1 10 vn:4 vd:4 1000 n:1 q:1 m:1 1 vm:4 VFMAL_s A1 11111110 0 d:1 00 vn:4 vd:4 1000 n:1 q:1 m:1 1 vm:4 VFMSL_s A1 11111110 1 d:1 00 vn:4 vd:4 1000 n:1 q:1 m:1 1 vm:4 +@v8_2_fp16 + +# v8.2-FP16 adds a lot of "and 16-bit flavour" to existing insn encodings; +# these patterns are arranged in the same order as the earlier v7 patterns. +# Pattern names follow the non-fp16 names with a _f16 suffix. + +# FP16: neon 3-reg-same: bit 20 sz=1 for f16 +VCGT_f16 A2 1111 0011 0 d 1 1 vn:4 vd:4 1110 n q m 0 vm:4 +VCGE_f16 A2 1111 0011 0 d 0 1 vn:4 vd:4 1110 n q m 0 vm:4 +VCEQ_f16 A2 1111 0010 0 d 0 1 vn:4 vd:4 1110 n q m 0 vm:4 +VFM_f16 A1 1111 0010 0 d op 1 vn:4 vd:4 1100 n q m 1 vm:4 +VADD_float_f16 A1 1111 0010 0 d 0 1 vn:4 vd:4 1101 n q m 0 vm:4 +VSUB_float_f16 A1 1111 0010 0 d 1 1 vn:4 vd:4 1101 n q m 0 vm:4 +VPADD_float_f16 A1 1111 0011 0 d 0 1 vn:4 vd:4 1101 n q m 0 vm:4 +VABD_float_f16 A1 1111 0011 0 d 1 1 vn:4 vd:4 1101 n q m 0 vm:4 +VMLA_float_f16 A1 1111 0010 0 d 0 1 vn:4 vd:4 1101 n q m 1 vm:4 +VMLS_float_f16 A1 1111 0010 0 d 1 1 vn:4 vd:4 1101 n q m 1 vm:4 +VMUL_float_f16 A1 1111 0011 0 d 0 1 vn:4 vd:4 1101 n q m 1 vm:4 +VACGE_f16 A1 1111 0011 0 d 0 1 vn:4 vd:4 1110 n q m 1 vm:4 +VACGT_f16 A1 1111 0011 0 d 1 1 vn:4 vd:4 1110 n q m 1 vm:4 +VMAX_float_f16 A1 1111 0010 0 d 0 1 vn:4 vd:4 1111 n q m 0 vm:4 +VMIN_float_f16 A1 1111 0010 0 d 1 1 vn:4 vd:4 1111 n q m 0 vm:4 +VPMAX_float_f16 A1 1111 0011 0 d 0 1 vn:4 vd:4 1111 n q m 0 vm:4 +VPMIN_float_f16 A1 1111 0011 0 d 1 1 vn:4 vd:4 1111 n q m 0 vm:4 +VRECPS_f16 A1 1111 0010 0 d 0 1 vn:4 vd:4 1111 n q m 1 vm:4 +VRSQRTS_f16 A1 1111 0010 0 d 1 1 vn:4 vd:4 1111 n q m 1 vm:4 + +# FP16: neon 2-reg-scalar : f=1 sz=01 +VMLA_scalar_f16 A1 1111 001 q 1 d 01 vn:4 vd:4 0 0 0 f n 1 m 0 vm:4 +VMLS_scalar_f16 A1 1111 001 q 1 d 01 vn:4 vd:4 0 1 0 f n 1 m 0 vm:4 +VMUL_scalar_f16 A1 1111 001 q 1 d 01 vn:4 vd:4 100 f n 1 m 0 vm:4 + +# FP16: Neon 2-reg-shift +# this doesn't overlap with the non-fp16 insn, which has 111 in [11:9] +VCVT_f16 A1 1111 001 u 1 d imm:6 vd:4 110 op 0 q m 1 vm:4 { ($imm & 0x38) != 0; } + +# FP16: neon 2-reg-misc: f=1 sz=01 +VCGT0_f16 A1 1111 0011 1 d 11 01 01 vd:4 0 f 000 q m 0 vm:4 +VCGE0_f16 A1 1111 0011 1 d 11 01 01 vd:4 0 f 001 q m 0 vm:4 +VCEQ0_f16 A1 1111 0011 1 d 11 01 01 vd:4 0 f 010 q m 0 vm:4 +VCLE0_f16 A1 1111 0011 1 d 11 01 01 vd:4 0 f 011 q m 0 vm:4 +VCLT0_f16 A1 1111 0011 1 d 11 01 01 vd:4 0 f 100 q m 0 vm:4 +VABS_f16 A1 1111 0011 1 d 11 01 01 vd:4 0 f 110 q m 0 vm:4 +VNEG_f16 A1 1111 0011 1 d 11 01 01 vd:4 0 f 111 q m 0 vm:4 +VRECPE_f16 A1 1111 0011 1 d 11 01 11 vd:4 010 f 0 q m 0 vm:4 +VRSQRTE_f16 A1 1111 0011 1 d 11 01 11 vd:4 010 f 1 q m 0 vm:4 +VCVT_neon_f16 A1 1111 0011 1 d 11 01 11 vd:4 0 11 op:2 q m 0 vm:4 + +# FP16: vfp: these have no overlap with non-fp16 patterns, where [11:9] is 101 +VMLA_f16 A2 cond:4 11100 d 00 vn:4 vd:4 1001 n op m 0 vm:4 +VNMLA_f16 A1 cond:4 11100 d 01 vn:4 vd:4 1001 n op m 0 vm:4 +VNMUL_f16 A2 cond:4 11100 d 10 vn:4 vd:4 1001 n 1 m 0 vm:4 +VMUL_f16 A2 cond:4 11100 d 10 vn:4 vd:4 1001 n 0 m 0 vm:4 +VADD_f16 A2 cond:4 11100 d 11 vn:4 vd:4 1001 n 0 m 0 vm:4 +VSUB_f16 A2 cond:4 11100 d 11 vn:4 vd:4 1001 n 1 m 0 vm:4 +VDIV_f16 A1 cond:4 11101 d 00 vn:4 vd:4 1001 n 0 m 0 vm:4 +VMOV_imm_f16 A2 cond:4 11101 d 11 immh:4 vd:4 1001 0000 imml:4 +VABS_f16 A2 cond:4 11101 d 11 0000 vd:4 1001 1 1 m 0 vm:4 +VNEG_f16 A2 cond:4 11101 d 11 0001 vd:4 1001 0 1 m 0 vm:4 +VSQRT_f16 A1 cond:4 11101 d 11 0001 vd:4 1001 1 1 m 0 vm:4 +VCMP_f16 A1 cond:4 11101 d 11 0100 vd:4 1001 e 1 m 0 vm:4 +VCMP_f16 A2 cond:4 11101 d 11 0101 vd:4 1001 e 1 0 0 0000 +VCVT_a_f16 A1 cond:4 11101 d 111 000 vd:4 1001 op 1 m 0 vm:4 +VCVT_b_f16 A1 cond:4 11101 d 111 10 x vd:4 1001 op 1 m 0 vm:4 +# VCVT between fp and fixed point (A.8.6.297); same UNPREDICTABLE as non-fp16 +# sx==1 case first: +VCVT_c_f16 A1 cond:4 11101 d 111 op 1 u vd:4 1001 1 1 i 0 imm:4 +# sx==0, bit 3 == 0 +VCVT_d_f16 A1 cond:4 11101 d 111 op 1 u vd:4 1001 0 1 i 0 0 imm:3 +# sx==0, bit 3 == 1, bits 2..0 and 5 0 +VCVT_e_f16 A1 cond:4 11101 d 111 op 1 u vd:4 1001 0 1 0 0 1000 +VFM_f16 A2 cond:4 11101 d 10 vn:4 vd:4 1001 n op m 0 vm:4 +VFNM_f16 A1 cond:4 11101 d 01 vn:4 vd:4 1001 n op m 0 vm:4 +# both A1 and A2 encodings, U = 1 +VSTR_f16 A1a cond:4 1101 1 d 00 rn:4 vd:4 1001 imm:8 \ + !memory { reg_plus_imm($rn, $imm * 2); } +# both A1 and A2 encodings, U = 0 +VSTR_f16 A1b cond:4 1101 0 d 00 rn:4 vd:4 1001 imm:8 \ + !memory { reg_minus_imm($rn, $imm * 2); } +# both A1 and A2 encodings, U = 1 +VLDR_f16 A1a cond:4 1101 1 d 01 rn:4 vd:4 1001 imm:8 \ + !memory { reg_plus_imm($rn, $imm * 2); } +# both A1 and A2 encodings, U = 0 +VLDR_f16 A1b cond:4 1101 0 d 01 rn:4 vd:4 1001 imm:8 \ + !memory { reg_minus_imm($rn, $imm * 2); } + +# FP16: v8-only insns +# Neon insns with sz=0b01 +VCVT_rm_neon_f16 A1 1111 00111 d 11 01 11 vd:4 00 rm:2 op q m 0 vm:4 +VRINTX_neon_f16 A1 1111 00111 d 11 01 10 vd:4 01001 q m 0 vm:4 +VRINTZ_neon_f16 A1 1111 00111 d 11 01 10 vd:4 01011 q m 0 vm:4 +VRINTANPM_neon_f16 A1 1111 00111 d 11 01 10 vd:4 01 op:3 q m 0 vm:4 +# Neon insn with sz=1 +VMINMAXNM_f16 A1 1111 00110 d op 1 vn:4 vd:4 1111 n q m 1 vm:4 +# VFP insns which don't overlap non-fp16 rules (which have 101 in [11:9]) +VCVT_rm_f16 A1 1111 11101 d 1111 rm:2 vd:4 1001 op 1 m 0 vm:4 +VSEL_f16 A1 1111 11100 d cc:2 vn:4 vd:4 1001 n 0 m 0 vm:4 +VMINMAXNM_f16 A2 1111 11101 d 00 vn:4 vd:4 1001 n op m 0 vm:4 +VRINTX_f16 A1 cond:4 11101 d 110111 vd:4 1001 0 1 m 0 vm:4 +VRINTZR_f16 A1 cond:4 11101 d 110110 vd:4 1001 op 1 m 0 vm:4 +VRINTANPM_f16 A1 1111 11101 d 1110 rmode:2 vd:4 1001 0 1 m 0 vm:4 + +# FP16: Insns which are new for v8.2 FP16: +VINS_f16 A1 1111 11101 d 110000 vd:4 101011 m 0 vm:4 +VMOVX_f16 A1 1111 11101 d 110000 vd:4 101001 m 0 vm:4 +# VMOV between general-purpose register and half-precision +VMOV_core_f16 A1 cond:4 1110000 op:1 vn:4 rt:4 1001 n 0010000 + +@v8_2_fp16_v8_3_compnum +# These are only present if both v8.2-FP16 and v8.3-CompNum are implemented +# sz=0 for FP16 +VCADD_f16 A1 1111110 rot:1 1 d:1 0 0 vn:4 vd:4 1000 n:1 q:1 m:1 0 vm:4 +VCMLA_f16 A1 1111110 rot:2 d:1 1 0 vn:4 vd:4 1000 n:1 q:1 m:1 0 vm:4 +VCMLA_s_f16 A1 11111110 0 d:1 rot:2 vn:4 vd:4 1000 n:1 q:1 m:1 0 vm:4 + # # ARMv8.3 extensions # @v8_3_compnum -# Disable fp16 until qemu supports it. -VCADD A1 1111110 rot:1 1 d:1 0 s:1 vn:4 vd:4 1000 n:1 q:1 m:1 0 vm:4 \ -!constraints { $s != 0; } - -VCMLA A1 1111110 rot:2 d:1 1 s:1 vn:4 vd:4 1000 n:1 q:1 m:1 0 vm:4 \ -!constraints { $s != 0; } -VCMLA_s A1 11111110 s:1 d:1 rot:2 vn:4 vd:4 1000 n:1 q:1 m:1 0 vm:4 \ -!constraints { $s != 0; } +# We avoid the FP16 parts of this, which are in @v8_2_fp16_v8_3_compnum, +# so here s=1 +VCADD A1 1111110 rot:1 1 d:1 0 1 vn:4 vd:4 1000 n:1 q:1 m:1 0 vm:4 +VCMLA A1 1111110 rot:2 d:1 1 1 vn:4 vd:4 1000 n:1 q:1 m:1 0 vm:4 +VCMLA_s A1 11111110 1 d:1 rot:2 vn:4 vd:4 1000 n:1 q:1 m:1 0 vm:4
Signature · 1 line
2.20.1
PATCH 1/1 configure: Test that gio libs from pkg-config work
In reply to Peter MaydellOn some hosts (eg Ubuntu Bionic) pkg-config returns a set of libraries for gio-2.0 which don't actually work when compiling statically. (Specifically, the returned library string includes -lmount, but not -lblkid which -lmount depends upon, so linking fails due to missing symbols.)
Check that the libraries work, and don't enable gio if they don't, in the same way we do for gnutls.
---
I wanted a statically-linked system emulation binary (which, yes, I know is not really something we support :-)). I got one with suitably liberal use of --disable-foo configure options, and this was the only thing I couldn't work around that way. The patch is needed because there's no --disable-gio. I suppose we could add that instead (or as well)...
Possibly meson offers a nicer way to do this, but this was simple and gnutls is doing the check this way already.
--- configure | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-)
configure +9 -1
@@ -3762,13 +3762,21 @@ if test "$static" = yes && test "$mingw32" = yes; then fi if $pkg_config --atleast-version=$glib_req_ver gio-2.0; then - gio=yes gio_cflags=$($pkg_config --cflags gio-2.0) gio_libs=$($pkg_config --libs gio-2.0) gdbus_codegen=$($pkg_config --variable=gdbus_codegen gio-2.0) if [ ! -x "$gdbus_codegen" ]; then gdbus_codegen= fi + # Check that the libraries actually work -- Ubuntu 18.04 ships + # with pkg-config --static --libs data for gio-2.0 that is missing + # -lblkid and will give a link error. + write_c_skeleton + if compile_prog "" "gio_libs" ; then + gio=yes + else + gio=no + fi else gio=no fi
Signature · 1 line
2.20.1
PATCH 1/1 docs/system/arm/virt: Document mte machine option
In reply to Peter MaydellCommit 6a0b7505f1fd6769c which added documentation of the virt board crossed in the post with commit 6f4e1405b91da0d0 which added a new 'mte' machine option. Update the docs to include the new option.
--- docs/system/arm/virt.rst | 4 ++++ 1 file changed, 4 insertions(+)
docs/system/arm/virt.rst +4 -0
@@ -79,6 +79,10 @@ virtualization Set ``on``/``off`` to enable/disable emulating a guest CPU which implements the Arm Virtualization Extensions. The default is ``off``. +mte + Set ``on``/``off`` to enable/disable emulating a guest CPU which implements the + Arm Memory Tagging Extensions. The default is ``off``. + highmem Set ``on``/``off`` to enable/disable placing devices and RAM in physical address space above 32 bits. The default is ``on`` for machine types
Signature · 1 line
2.20.1
Re: [PATCH for-5.1] docs/system/arm/virt: Document mte machine option
Patchew URL: https://patchew.org/QEMU/[email protected]/
Patchew URL: https://patchew.org/QEMU/[email protected]/
Hi,
This series seems to have some coding style problems. See output below for more information:
Type: series
Message-id: [email protected]
Subject: [PATCH for-5.1] docs/system/arm/virt: Document mte machine option
=== TEST SCRIPT BEGIN ===
#!/bin/bash
git rev-parse base > /dev/null || exit 0
git config --local diff.renamelimit 0
git config --local diff.renames True
git config --local diff.algorithm histogram./scripts/checkpatch.pl --mailback base..
=== TEST SCRIPT END ===
Updating 3c8cf5a9c21ff8782164d1def7f44bd888713384
From https://github.com/patchew-project/qemu
* [new tag] patchew/[email protected] -> patchew/[email protected]
Switched to a new branch 'test'
=== OUTPUT BEGIN ===
checkpatch.pl: no revisions returned for revlist '1' === OUTPUT END ===
Test command exited with code: 255
The full log is available at
http://patchew.org/logs/[email protected]/testing.checkpatch/?type=message.
---
Email generated automatically by Patchew [https://patchew.org/].
Please send your feedback to [email protected]
PATCH 1/10 decodetree: Fix codegen for non-overlapping group inside overlapping group
In reply to Peter MaydellFor nested groups like:
{
[
pattern 1
pattern 2
]
pattern 3
}the intended behaviour is that patterns 1 and 2 must not overlap with each other; if the insn matches neither then we fall through to pattern 3 as the next thing in the outer overlapping group.
Currently we generate incorrect code for this situation, because in the code path for a failed match inside the inner non-overlapping group we generate a "return" statement, which causes decode to stop entirely rather than continuing to the next thing in the outer group.
Generate a "break" instead, so that decode flow behaves as required for this nested group case.
--- scripts/decodetree.py | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
scripts/decodetree.py +1 -1
@@ -548,7 +548,7 @@ class Tree: output(ind, ' /* ', str_match_bits(innerbits, innermask), ' */\n') s.output_code(i + 4, extracted, innerbits, innermask) - output(ind, ' return false;\n') + output(ind, ' break;\n') output(ind, '}\n') # end Tree
Signature · 1 line
2.20.1
PATCH 1/1 hw/arm/armsse: Assert info->num_cpus is in-bounds in armsse_realize()
In reply to Peter MaydellIn armsse_realize() we have a loop over [0, info->num_cpus), which indexes into various fixed-size arrays in the ARMSSE struct. This confuses Coverity, which warns that we might overrun those arrays (CID 1430326, 1430337, 1430371, 1430414, 1430430). This can't actually happen, because the info struct is always one of the entries in the armsse_variants[] array and num_cpus is either 1 or 2; we also already assert in armsse_init() that num_cpus is not too large. However, adding an assert to armsse_realize() like the one in armsse_init() should help Coverity figure out that these code paths aren't possible.
--- hw/arm/armsse.c | 2 ++ 1 file changed, 2 insertions(+)
hw/arm/armsse.c +2 -0
@@ -452,6 +452,8 @@ static void armsse_realize(DeviceState *dev, Error **errp)return ; } +assert (info->num_cpus <=SSE_MAX_CPUS ); +/* max SRAM_ADDR_WIDTH: 24 - log2(SRAM_NUM_BANK) */ assert (is_power_of_2 (info->sram_banks)); addr_width_max =24 -ctz32 (info->sram_banks);
Signature · 1 line
2.20.1
PATCH 1/1 hw/input/virtio-input-hid.c: Don't undef CONFIG_CURSES
In reply to Peter Maydellvirtio-input-hid.c undefines CONFIG_CURSES before including ui/console.h. However since commits e2f82e924d057935 and b0766612d16da18 that header does not have behaviour dependent on CONFIG_CURSES. Remove the now-unneeded undef.
---
NB: tested with 'make check' only.
hw/input/virtio-input-hid.c | 1 - 1 file changed, 1 deletion(-)
hw/input/virtio-input-hid.c +0 -1
@@ -12,7 +12,6 @@#include "hw/qdev-properties.h" #include "hw/virtio/virtio-input.h" -#undef CONFIG_CURSES#include "ui/console.h" #include "standard-headers/linux/input.h"
Signature · 1 line
2.20.1
PATCH 1/1 hw/arm/netduino2, netduinoplus2: Set system_clock_scale
In reply to Peter MaydellThe netduino2 and netduinoplus2 boards forgot to set the system_clock_scale global, which meant that if guest code used the systick timer in "use the processor clock" mode it would hang because time never advances.
Set the global to match the documented CPU clock speed of these boards. Judging by the data sheet this is slightly simplistic because the SoC allows configuration of the SYSCLK source and frequency via the RCC (reset and clock control) module, but we don't model that.
---
NB: tested with "make check" only...
hw/arm/netduino2.c | 10 ++++++++++ hw/arm/netduinoplus2.c | 10 ++++++++++ 2 files changed, 20 insertions(+)
hw/arm/netduino2.c +10 -0
@@ -30,10 +30,20 @@#include "hw/arm/stm32f205_soc.h" #include "hw/arm/boot.h" +/* Main SYSCLK frequency in Hz (120MHz) */ +#define SYSCLK_FRQ 120000000ULL +static void netduino2_init (MachineState *machine) {DeviceState *dev; +/* +* TODO: ideally we would model the SoC RCC and let it handle +* system_clock_scale, including its ability to define different +* possible SYSCLK sources. +*/ + system_clock_scale =NANOSECONDS_PER_SECOND /SYSCLK_FRQ ; + dev =qdev_new (TYPE_STM32F205_SOC );qdev_prop_set_string (dev,"cpu-type" ,ARM_CPU_TYPE_NAME ("cortex-m3" ));sysbus_realize_and_unref (SYS_BUS_DEVICE (dev), &error_fatal);
hw/arm/netduinoplus2.c +10 -0
@@ -30,10 +30,20 @@#include "hw/arm/stm32f405_soc.h" #include "hw/arm/boot.h" +/* Main SYSCLK frequency in Hz (168MHz) */ +#define SYSCLK_FRQ 168000000ULL +static void netduinoplus2_init (MachineState *machine) {DeviceState *dev; +/* +* TODO: ideally we would model the SoC RCC and let it handle +* system_clock_scale, including its ability to define different +* possible SYSCLK sources. +*/ + system_clock_scale =NANOSECONDS_PER_SECOND /SYSCLK_FRQ ; + dev =qdev_new (TYPE_STM32F405_SOC );qdev_prop_set_string (dev,"cpu-type" ,ARM_CPU_TYPE_NAME ("cortex-m4" ));sysbus_realize_and_unref (SYS_BUS_DEVICE (dev), &error_fatal);
Signature · 1 line
2.20.1
Re: [PATCH for-5.1] hw/arm/netduino2, netduinoplus2: Set system_clock_scale
Quoted 5 lines · Peter Maydell
The netduino2 and netduinoplus2 boards forgot to set the
system_clock_scaleglobal, which meant that if guest code used the systick timer in "use the processor clock" mode it would hang because time never advances.
Quoted 7 lines
Set the global to match the documented CPU clock speed of these boards. Judging by the data sheet this is slightly simplistic because the SoC allows configuration of the SYSCLK source and frequency via the RCC (reset and clock control) module, but we don't model that.
Signed-off-by Peter Maydell <[email protected]>
Alistair
Quoted 61 lines
---
NB: tested with "make check" only...hw/arm/netduino2.c | 10 ++++++++++ hw/arm/netduinoplus2.c | 10 ++++++++++ 2 files changed, 20 insertions(+)hw/arm/netduino2.c +10
-0@@ -30,10 +30,20 @@#include "hw/arm/stm32f205_soc.h" #include "hw/arm/boot.h" +/* Main SYSCLK frequency in Hz (120MHz) */ +#define SYSCLK_FRQ 120000000ULL +static void netduino2_init (MachineState *machine) {DeviceState *dev; +/* +* TODO: ideally we would model the SoC RCC and let it handle +* system_clock_scale, including its ability to define different +* possible SYSCLK sources. +*/ + system_clock_scale =NANOSECONDS_PER_SECOND /SYSCLK_FRQ ; + dev =qdev_new (TYPE_STM32F205_SOC );qdev_prop_set_string (dev,"cpu-type" ,ARM_CPU_TYPE_NAME ("cortex-m3" ));sysbus_realize_and_unref (SYS_BUS_DEVICE (dev), &error_fatal);hw/arm/netduinoplus2.c +10
-1@@ -30,10 +30,20 @@#include "hw/arm/stm32f405_soc.h" #include "hw/arm/boot.h" +/* Main SYSCLK frequency in Hz (168MHz) */ +#define SYSCLK_FRQ 168000000ULL +static void netduinoplus2_init (MachineState *machine) {DeviceState *dev; +/* +* TODO: ideally we would model the SoC RCC and let it handle +* system_clock_scale, including its ability to define different +* possible SYSCLK sources. +*/ + system_clock_scale =NANOSECONDS_PER_SECOND /SYSCLK_FRQ ; + dev =qdev_new (TYPE_STM32F405_SOC );qdev_prop_set_string (dev,"cpu-type" ,ARM_CPU_TYPE_NAME ("cortex-m4" ));sysbus_realize_and_unref (SYS_BUS_DEVICE (dev), &error_fatal); --2.20.1
Re: [PATCH for-5.1] hw/arm/netduino2, netduinoplus2: Set system_clock_scale
Quoted 7 lines · Alistair Francis
Quoted 5 lines · Peter Maydell
The netduino2 and netduinoplus2 boards forgot to set the
system_clock_scaleglobal, which meant that if guest code used the systick timer in "use the processor clock" mode it would hang because time never advances.
Quoted 6 lines
Quoted 6 lines
Set the global to match the documented CPU clock speed of these boards. Judging by the data sheet this is slightly simplistic because the SoC allows configuration of the SYSCLK source and frequency via the RCC (reset and clock control) module, but we don't model that.
Thanks for fixing this Peter.
Alistair
Quoted 67 lines
Quoted 1 line
Signed-off-by Peter Maydell <[email protected]>Reviewed-by Alistair Francis <[email protected]>Alistair
Quoted 61 lines
---
NB: tested with "make check" only...hw/arm/netduino2.c | 10 ++++++++++ hw/arm/netduinoplus2.c | 10 ++++++++++ 2 files changed, 20 insertions(+)hw/arm/netduino2.c +10
-0@@ -30,10 +30,20 @@#include "hw/arm/stm32f205_soc.h" #include "hw/arm/boot.h" +/* Main SYSCLK frequency in Hz (120MHz) */ +#define SYSCLK_FRQ 120000000ULL +static void netduino2_init (MachineState *machine) {DeviceState *dev; +/* +* TODO: ideally we would model the SoC RCC and let it handle +* system_clock_scale, including its ability to define different +* possible SYSCLK sources. +*/ + system_clock_scale =NANOSECONDS_PER_SECOND /SYSCLK_FRQ ; + dev =qdev_new (TYPE_STM32F205_SOC );qdev_prop_set_string (dev,"cpu-type" ,ARM_CPU_TYPE_NAME ("cortex-m3" ));sysbus_realize_and_unref (SYS_BUS_DEVICE (dev), &error_fatal);hw/arm/netduinoplus2.c +10
-1@@ -30,10 +30,20 @@#include "hw/arm/stm32f405_soc.h" #include "hw/arm/boot.h" +/* Main SYSCLK frequency in Hz (168MHz) */ +#define SYSCLK_FRQ 168000000ULL +static void netduinoplus2_init (MachineState *machine) {DeviceState *dev; +/* +* TODO: ideally we would model the SoC RCC and let it handle +* system_clock_scale, including its ability to define different +* possible SYSCLK sources. +*/ + system_clock_scale =NANOSECONDS_PER_SECOND /SYSCLK_FRQ ; + dev =qdev_new (TYPE_STM32F405_SOC );qdev_prop_set_string (dev,"cpu-type" ,ARM_CPU_TYPE_NAME ("cortex-m4" ));sysbus_realize_and_unref (SYS_BUS_DEVICE (dev), &error_fatal); --2.20.1
Re: [PATCH for-5.1] hw/arm/netduino2, netduinoplus2: Set system_clock_scale
Quoted 9 lines · Alistair Francis
Quoted 7 lines · Alistair Francis
Quoted 5 lines · Peter Maydell
The netduino2 and netduinoplus2 boards forgot to set the
system_clock_scaleglobal, which meant that if guest code used the systick timer in "use the processor clock" mode it would hang because time never advances.
Quoted 8 lines
Quoted 6 lines
Quoted 6 lines
Set the global to match the documented CPU clock speed of these boards. Judging by the data sheet this is slightly simplistic because the SoC allows configuration of the SYSCLK source and frequency via the RCC (reset and clock control) module, but we don't model that.
Thanks for fixing this Peter.
This is already in master (commit e7e5a9595ab) -- this email is one of a set of stale patchmails I sent out by mistake on Monday when I mangled a git send-email command. Sorry for the confusion.
-- PMM
Re: [PATCH for-5.1] hw/arm/netduino2, netduinoplus2: Set system_clock_scale
Quoted 16 lines · Peter Maydell
Quoted 14 lines · Alistair Francis
Quoted 12 lines · Alistair Francis
Quoted 10 lines · Peter Maydell
The netduino2 and netduinoplus2 boards forgot to set the
system_clock_scaleglobal, which meant that if guest code used the systick timer in "use the processor clock" mode it would hang because time never advances.Set the global to match the documented CPU clock speed of these boards. Judging by the data sheet this is slightly simplistic because the SoC allows configuration of the SYSCLK source and frequency via the RCC (reset and clock control) module, but we don't model that.
Quoted 5 lines
Quoted 3 lines
Quoted 1 line
Quoted 1 line
Thanks for fixing this Peter.
This is already in master (commit
e7e5a9595ab) -- this email is
I thought I saw that in the bug report, but I just assumed it was pointing to a branch.
Quoted 2 lines
one of a set of stale patchmails I sent out by mistake on Monday when I mangled a git send-email command. Sorry for the confusion.
Strange. No worries.
Alistair
Quoted 2 lines
-- PMM
PATCH 1/1 hw/timer/armv7m_systick: assert that board code set system_clock_scale
In reply to Peter MaydellIt is the responsibility of board code for an armv7m system to set system_clock_scale appropriately for the CPU speed of the core. If it forgets to do this, then QEMU will hang if the guest tries to use the systick timer in the "tick at the CPU clock frequency" mode.
We forgot that in a couple of our boards (see commits ce4f70e81ed23c93f, e7e5a9595ab1136). Add an assertion in the systick reset method so we don't let any new boards in with the same bug.
---
In the longer term we should make this a clocktree input and plumb it through the armv7m container and so on, but for the moment this assert() improves the current situation.
--- hw/timer/armv7m_systick.c | 8 ++++++++ 1 file changed, 8 insertions(+)
hw/timer/armv7m_systick.c +8 -0
@@ -202,6 +202,14 @@ static void systick_reset(DeviceState *dev) {SysTickState *s =SYSTICK (dev); +/* +* Forgetting to set system_clock_scale is always a board code +* bug. We can't check this earlier because for some boards +* (like stellaris) it is not yet configured at the point where +* the systick device is realized. +*/ +assert (system_clock_scale !=0 ); + s->control =0 ; s->reload =0 ; s->tick =0 ;
Signature · 1 line
2.20.1
PATCH 1/1 hw/arm/mps2: New board model mps2-386
In reply to Peter MaydellImplement a model of the MPS2 with the AN386 firmware. This is essentially identical to the AN385 firmware, but it has a Cortex-M4 rather than a Cortex-M3.
--- hw/arm/mps2.c | 30 +++++++++++++++++++++++++++--- 1 file changed, 27 insertions(+), 3 deletions(-)
hw/arm/mps2.c +27 -3
@@ -15,6 +15,7 @@* as seen by the guest depend significantly on the FPGA image. * We model the following FPGA images: * "mps2-an385" -- Cortex-M3 as documented in ARM Application Note AN385 +* "mps2-an386" -- Cortex-M4 as documented in ARM Application Note AN386 * "mps2-an511" -- Cortex-M3 'DesignStart' as documented in AN511 * * Links to the TRM for the board itself and to the various Application
@@ -47,6 +48,7 @@typedef enum MPS2FPGAType {FPGA_AN385 , +FPGA_AN386 ,FPGA_AN511 , }MPS2FPGAType ;
@@ -79,6 +81,7 @@ typedef struct {#define TYPE_MPS2_MACHINE "mps2"#define TYPE_MPS2_AN385_MACHINE MACHINE_TYPE_NAME("mps2-an385") +#define TYPE_MPS2_AN386_MACHINE MACHINE_TYPE_NAME("mps2-an386")#define TYPE_MPS2_AN511_MACHINE MACHINE_TYPE_NAME("mps2-an511")#define MPS2_MACHINE (obj) \
@@ -142,7 +145,7 @@ static void mps2_common_init(MachineState *machine)* * Common to both boards: * 0x21000000..0x21ffffff : PSRAM (16MB) -* AN385 only: +* AN385/AN386 only: * 0x00000000 .. 0x003fffff : ZBT SSRAM1 * 0x00400000 .. 0x007fffff : mirror of ZBT SSRAM1 * 0x20000000 .. 0x203fffff : ZBT SSRAM 2&3
@@ -157,7 +160,7 @@ static void mps2_common_init(MachineState *machine)* 0x20000000 .. 0x2001ffff : SRAM * 0x20400000 .. 0x207fffff : ZBT SSRAM 2&3 * -* The AN385 has a feature where the lowest 16K can be mapped +* The AN385/AN386 has a feature where the lowest 16K can be mapped * either to the bottom of the ZBT SSRAM1 or to the block RAM. * This is of no use for QEMU so we don't implement it (as if * zbt_boot_ctrl is always zero).
@@ -166,6 +169,7 @@ static void mps2_common_init(MachineState *machine)switch (mmc->fpga_type) {case FPGA_AN385 : +case FPGA_AN386 :make_ram (&mms->ssram1,"mps.ssram1" ,0x0 ,0x400000 );make_ram_alias (&mms->ssram1_m,"mps.ssram1_m" , &mms->ssram1,0x400000 );make_ram (&mms->ssram23,"mps.ssram23" ,0x20000000 ,0x400000 );
@@ -193,6 +197,7 @@ static void mps2_common_init(MachineState *machine) armv7m =DEVICE (&mms->armv7m);switch (mmc->fpga_type) {case FPGA_AN385 : +case FPGA_AN386 :qdev_prop_set_uint32 (armv7m,"num-irq" ,32 );break ;case FPGA_AN511 :
@@ -229,6 +234,7 @@ static void mps2_common_init(MachineState *machine)switch (mmc->fpga_type) {case FPGA_AN385 : +case FPGA_AN386 : {/* The overflow IRQs for UARTs 0, 1 and 2 are ORed together. * Overflow for UARTs 4 and 5 doesn't trigger any interrupt.
@@ -380,7 +386,7 @@ static void mps2_common_init(MachineState *machine)*/ lan9118_init (&nd_table[0 ],0x40200000 ,qdev_get_gpio_in (armv7m, - mmc->fpga_type ==FPGA_AN385 ?13 :47 )); + mmc->fpga_type ==FPGA_AN511 ?47 :13 )); system_clock_scale =NANOSECONDS_PER_SECOND /SYSCLK_FRQ ;
@@ -409,6 +415,17 @@ static void mps2_an385_class_init(ObjectClass *oc, void *data) mmc->scc_id =0x41043850 ; } +static void mps2_an386_class_init (ObjectClass *oc,void *data) +{ +MachineClass *mc =MACHINE_CLASS (oc); +MPS2MachineClass *mmc =MPS2_MACHINE_CLASS (oc); + + mc->desc ="ARM MPS2 with AN386 FPGA image for Cortex-M4" ; + mmc->fpga_type =FPGA_AN386 ; + mc->default_cpu_type =ARM_CPU_TYPE_NAME ("cortex-m4" ); + mmc->scc_id =0x41043860 ; +} +static void mps2_an511_class_init (ObjectClass *oc,void *data) {MachineClass *mc =MACHINE_CLASS (oc);
@@ -435,6 +452,12 @@ static const TypeInfo mps2_an385_info = { .class_init = mps2_an385_class_init, }; +static const TypeInfo mps2_an386_info = { + .name =TYPE_MPS2_AN386_MACHINE , + .parent =TYPE_MPS2_MACHINE , + .class_init = mps2_an386_class_init, +}; +static const TypeInfo mps2_an511_info = { .name =TYPE_MPS2_AN511_MACHINE , .parent =TYPE_MPS2_MACHINE ,
@@ -445,6 +468,7 @@ static void mps2_machine_init(void) {type_register_static (&mps2_info);type_register_static (&mps2_an385_info); +type_register_static (&mps2_an386_info);type_register_static (&mps2_an511_info); }
Signature · 1 line
2.20.1
PATCH 1/1 hw/timer/imx_epit: Avoid assertion when CR.SWR is written
In reply to Peter MaydellThe imx_epit device has a software-controllable reset triggered by setting the SWR bit in the CR register. An error in commit cc2722ec83ad9 means that we will end up assert()ing if the guest does this, because the code in imx_epit_write() starts ptimer transactions, and then imx_epit_reset() also starts ptimre transactions, triggering "ptimer_transaction_begin: Assertion `!s->in_transaction' failed".
The cleanest way to avoid this double-transaction is to move the start-transaction for the CR write handling down below the check of the SWR bit.
---
I don't have a test image for KZM so this is the minimal obviously-safe change. I'm pretty sure that actually we could add a "break" after the imx_epit_reset() call because all of the work done by the following code is duplicating the ptimer setup done by the reset function. But I'm not really happy making that change without a test image...
--- hw/timer/imx_epit.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-)
hw/timer/imx_epit.c +6 -3
@@ -199,15 +199,18 @@ static void imx_epit_write(void *opaque, hwaddr offset, uint64_t value,switch (offset >>2 ) {case 0 :/* CR */ -ptimer_transaction_begin (s->timer_cmp); -ptimer_transaction_begin (s->timer_reload); oldcr = s->cr; s->cr = value &0x03ffffff ;if (s->cr &CR_SWR ) {/* handle the reset */ imx_epit_reset (DEVICE (s)); - }else { + } + +ptimer_transaction_begin (s->timer_cmp); +ptimer_transaction_begin (s->timer_reload); + +if (!(s->cr &CR_SWR )) {imx_epit_set_freq (s); }
Signature · 1 line
2.20.1
RFC PATCH v2 1/1 linux-user: Use FD_32BIT_MODE fd flag for 32-bit guests
In reply to Peter MaydellIf the guest is 32 bit then there is a potential problem if the host gives us back a 64-bit sized value that we can't fit into the ABI the guest requires. This is a theoretical issue for many syscalls, but a real issue for directory reads where the host is using ext3 or ext4. There the 'offset' values retured via the getdents syscall are hashes, and on a 64-bit system they will always fill the full 64 bits.
Use the FD_32BIT_MODE fd flag to tell the kernel to stick to 32-bit sized hashes for fds used by the guest.
This is an RFC patch because the kernel patch that adds the new fd flag hasn't yet been accepted upstream. The kernel patch is:
https://patchew.org/QEMU/[email protected]/
---
This is just a minor update of the testing patch I sent out in the thread discussing Linus's v1 kernel patch.
linux-user/syscall.c | 32 ++++++++++++++++++++++++++++++++ 1 file changed, 32 insertions(+)
linux-user/syscall.c +32 -0
@@ -884,6 +884,33 @@ static inline int host_to_target_sock_type(int host_type)return target_type; } +/* +* If the guest is using a 32 bit ABI then we should try to ask the kernel +* to provide 32-bit offsets in getdents syscalls, as otherwise some +* filesystems will return 64-bit hash values which we can't fit into +* the field sizes the guest ABI mandates. +*/ +#ifndef FD_32BIT_MODE +#define FD_32BIT_MODE 2 +#endif + +static inline void request_32bit_fs (int fd) +{ +#if HOST_LONG_BITS >TARGET_ABI_BITS +/* +* Ignore errors, which are likely due to the host kernel being +* too old to support FD_32BIT_MODE. We'll continue anyway, which +* might or might not work, depending on the guest code and on the +* host filesystem. +*/ +int flags =fcntl (fd,F_GETFD ); +if (flags ==-1 ) { +return ; + } +fcntl (fd,F_SETFD , flags |FD_32BIT_MODE ); +#endif +} +static abi_ulong target_brk;static abi_ulong target_original_brk;static abi_ulong brk_page;
@@ -7725,6 +7752,7 @@ static abi_long do_syscall1(void *cpu_env, int num, abi_long arg1,target_to_host_bitmask (arg2, fcntl_flags_tbl), arg3));fd_trans_unregister (ret); +request_32bit_fs (ret);unlock_user (p, arg1,0 );return ret;#endif
@@ -7735,6 +7763,7 @@ static abi_long do_syscall1(void *cpu_env, int num, abi_long arg1,target_to_host_bitmask (arg3, fcntl_flags_tbl), arg4));fd_trans_unregister (ret); +request_32bit_fs (ret);unlock_user (p, arg2,0 );return ret;#if defined(TARGET_NR_name_to_handle_at) && defined(CONFIG_OPEN_BY_HANDLE )
@@ -7746,6 +7775,7 @@ static abi_long do_syscall1(void *cpu_env, int num, abi_long arg1,case TARGET_NR_open_by_handle_at: ret =do_open_by_handle_at (arg1, arg2, arg3);fd_trans_unregister (ret); +request_32bit_fs (ret);return ret;#endif case TARGET_NR_close:
@@ -7790,6 +7820,7 @@ static abi_long do_syscall1(void *cpu_env, int num, abi_long arg1,return -TARGET_EFAULT ; ret =get_errno (creat (p, arg2));fd_trans_unregister (ret); +request_32bit_fs (ret);unlock_user (p, arg1,0 );return ret;#endif
@@ -12419,6 +12450,7 @@ static abi_long do_syscall1(void *cpu_env, int num, abi_long arg1, } ret =get_errno (memfd_create (p, arg2));fd_trans_unregister (ret); +request_32bit_fs (ret);unlock_user (p, arg1,0 );return ret;#endif
Signature · 1 line
2.20.1
PATCH 1/1 hw/display/bcm2835_fb.c: Initialize all fields of struct
In reply to Peter MaydellIn bcm2835_fb_mbox_push(), Coverity complains (CID 1429989) that we pass a pointer to a local struct to another function without initializing all its fields. This is a real bug:bcm2835_fb_reconfigure() copies the whole of our new BCM2385FBConfig struct into s->config, so any fields we don't initialize will corrupt the state of the device.
Copy the two fields which we don't want to update (pixo and alpha) from the existing config so we don't accidentally change them.
---
Not sure why this wasn't a visible bug -- alpha isn't used, but if pixo changes from zero to non-zero we flip from RGB to BGR...
--- hw/display/bcm2835_fb.c | 4 ++++ 1 file changed, 4 insertions(+)
hw/display/bcm2835_fb.c +4 -0
@@ -282,6 +282,10 @@ static void bcm2835_fb_mbox_push(BCM2835FBState *s, uint32_t value) newconf.base = s->vcram_base | (value &0xc0000000 ); newconf.base +=BCM2835_FB_OFFSET ; +/* Copy fields which we don't want to change from the existing config */ + newconf.pixo = s->config.pixo; + newconf.alpha = s->config.alpha; +bcm2835_fb_validate_config (&newconf); pitch =bcm2835_fb_get_pitch (&newconf);
Signature · 1 line
2.20.1
PATCH 1/1 qapi/machine.json: Fix missing newline in doc comment
In reply to Peter MaydellIn commit 176d2cda0dee9f4 we added the @die-id field to the CpuInstanceProperties struct, but in the process accidentally removed the newline between the doc-comment lines for @core-id and @thread-id.
Put the newline back in; this fixes a misformatting in the generated HTML QMP reference manual.
---
Not very important but I've suggested for-5.1 as it's a safe docs fix. You can see the misrendered doc at
https://www.qemu.org/docs/master/interop/qemu-qmp-ref.html#index-CpuInstanceProperties
qapi/machine.json | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
qapi/machine.json +2 -1
@@ -825,7 +825,8 @@ # @node-id: NUMA node ID the CPU belongs to # @socket-id: socket number within node/board the CPU belongs to # @die-id: die number within node/board the CPU belongs to (Since 4.1) -# @core-id: core number within die the CPU belongs to# @thread-id: thread number within core the CPU belongs to +# @core-id: core number within die the CPU belongs to +# @thread-id: thread number within core the CPU belongs to # # Note: currently there are 5 properties that could be present # but management should be prepared to pass through other
Signature · 1 line
2.20.1
PATCH 1/1 hw/intc/arm_gicv3_cpuif: Don't copy CPU's maintenance interrupt
In reply to Peter MaydellIn gicv3_init_cpuif() we copy the ARMCPU gicv3_maintenance_interrupt into the GICv3CPUState struct's maintenance_irq field. This will only work if the board happens to have already wired up the CPU maintenance IRQ before the GIC was realized. Unfortunately this is not the case for the 'virt' board, and so the value that gets copied is NULL (since a qemu_irq is really a pointer to an IRQState struct under the hood). The effect is that the CPU interface code never actually raises the maintenance in2Dterrupt line.
Instead, since the GICv3CPUState has a pointer to the CPUState, make the dereference at the point where we want to raise the interrupt, to avoid an implicit requirement on board code to wire things up in a particular order.
---
QEMU's implementation here is a bit odd because we've put all the logic into the "GIC" device where in real hardware it's split between a GIC device and the CPU interface part in the CPU. If we had arranged it in that way then we wouldn't have this odd bit of code where the GIC device needs to raise an IRQ line that belongs to the CPU.
Not sure why we've never noticed this bug previously with KVM as a guest, you'd think we'd have spotted "maintenance interrupts just don't work"...
--- include/hw/intc/arm_gicv3_common.h | 1 - hw/intc/arm_gicv3_cpuif.c | 5 ++--- 2 files changed, 2 insertions(+), 4 deletions(-)
include/hw/intc/arm_gicv3_common.h +0 -1
@@ -153,7 +153,6 @@ struct GICv3CPUState {qemu_irq parent_fiq;qemu_irq parent_virq;qemu_irq parent_vfiq; -qemu_irq maintenance_irq;/* Redistributor */ uint32_t level;/* Current IRQ level */
hw/intc/arm_gicv3_cpuif.c +2 -3
@@ -399,6 +399,7 @@ static void gicv3_cpuif_virt_update(GICv3CPUState *cs)int irqlevel =0 ;int fiqlevel =0 ;int maintlevel =0 ; +ARMCPU *cpu =ARM_CPU (cs->cpu); idx =hppvi_index (cs);trace_gicv3_cpuif_virt_update (gicv3_redist_affid (cs), idx);
@@ -424,7 +425,7 @@ static void gicv3_cpuif_virt_update(GICv3CPUState *cs)qemu_set_irq (cs->parent_vfiq, fiqlevel);qemu_set_irq (cs->parent_virq, irqlevel); -qemu_set_irq (cs->maintenance_irq, maintlevel); +qemu_set_irq (cpu->gicv3_maintenance_interrupt, maintlevel); }static uint64_t icv_ap_read (CPUARMState *env,const ARMCPRegInfo *ri)
@@ -2624,8 +2625,6 @@ void gicv3_init_cpuif(GICv3State *s) && cpu->gic_num_lrs) {int j; - cs->maintenance_irq = cpu->gicv3_maintenance_interrupt; - cs->num_list_regs = cpu->gic_num_lrs; cs->vpribits = cpu->gic_vpribits; cs->vprebits = cpu->gic_vprebits;
Signature · 1 line
2.20.1
PATCH 1/1 msf2-soc, stellaris: Don't wire up SYSRESETREQ
In reply to Peter MaydellThe MSF2 SoC model and the Stellaris board code both wire SYSRESETREQ up to a function that just invokes
qemu_system_reset_request(SHUTDOWN_CAUSE_GUEST_RESET);
This is now the default action that the NVIC does if the line is not connected, so we can delete the handling code.
--- hw/arm/msf2-soc.c | 11 ----------- hw/arm/stellaris.c | 12 ------------ 2 files changed, 23 deletions(-)
hw/arm/msf2-soc.c +0 -11
@@ -30,7 +30,6 @@#include "hw/irq.h" #include "hw/arm/msf2-soc.h" #include "hw/misc/unimp.h" -#include "sysemu/runstate.h" #include "sysemu/sysemu.h" #define MSF2_TIMER_BASE 0x40004000
@@ -59,13 +58,6 @@ static const int spi_irq[MSF2_NUM_SPIS] = { 2, 3 };static const int uart_irq[MSF2_NUM_UARTS ] = {10 ,11 };static const int timer_irq[MSF2_NUM_TIMERS ] = {14 ,15 }; -static void do_sys_reset (void *opaque,int n,int level) -{ -if (level) { -qemu_system_reset_request (SHUTDOWN_CAUSE_GUEST_RESET ); - } -} -static void m2sxxx_soc_initfn (Object *obj) {MSF2State *s =MSF2_SOC (obj);
@@ -130,9 +122,6 @@ static void m2sxxx_soc_realize(DeviceState *dev_soc, Error **errp)return ; } -qdev_connect_gpio_out_named (DEVICE (&s->armv7m.nvic),"SYSRESETREQ" ,0 , -qemu_allocate_irq (&do_sys_reset,NULL ,0 )); - system_clock_scale =NANOSECONDS_PER_SECOND / s->m3clk;for (i =0 ; i <MSF2_NUM_UARTS ; i++) {
hw/arm/stellaris.c +0 -12
@@ -18,7 +18,6 @@#include "hw/boards.h" #include "qemu/log.h" #include "exec/address-spaces.h" -#include "sysemu/runstate.h" #include "sysemu/sysemu.h" #include "hw/arm/armv7m.h" #include "hw/char/pl011.h"
@@ -1206,14 +1205,6 @@ static void stellaris_adc_init(Object *obj)qdev_init_gpio_in (dev, stellaris_adc_trigger,1 ); } -static -void do_sys_reset (void *opaque,int n,int level) -{ -if (level) { -qemu_system_reset_request (SHUTDOWN_CAUSE_GUEST_RESET ); - } -} -/* Board init. */ static stellaris_board_info stellaris_boards[] = { {"LM3S811EVB" ,
@@ -1317,9 +1308,6 @@ static void stellaris_init(MachineState *ms, stellaris_board_info *board)/* This will exit with an error if the user passed us a bad cpu_type */ sysbus_realize_and_unref (SYS_BUS_DEVICE (nvic), &error_fatal); -qdev_connect_gpio_out_named (nvic,"SYSRESETREQ" ,0 , -qemu_allocate_irq (&do_sys_reset,NULL ,0 )); -if (board->dc1 & (1 <<16 )) { dev = sysbus_create_varargs(TYPE_STELLARIS_ADC, 0x40038000, qdev_get_gpio_in(nvic, 14),
Signature · 1 line
2.20.1
PATCH 1/1 hw/virtio/virtio-iommu-pci.c: Fix typo in error message
In reply to Peter MaydellFix a typo in an error message in virtio_iommu_pci_realize():
"Check you machine" should be "Check your machine".
--- hw/virtio/virtio-iommu-pci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
hw/virtio/virtio-iommu-pci.c +1 -1
@@ -48,7 +48,7 @@ static void virtio_iommu_pci_realize(VirtIOPCIProxy *vpci_dev, Error **errp)"%s machine fails to create iommu-map device tree bindings" , mc->name);error_append_hint (errp, -"Check you machine implements a hotplug handler " +"Check your machine implements a hotplug handler " "for the virtio-iommu-pci device\n" );error_append_hint (errp,"Check the guest is booted without FW or with " "-no-acpi\n" );
Signature · 1 line
2.20.1
PATCH 1/1 hw/intc/arm_gicv3_cpuif: Make GIC maintenance interrupts work
In reply to Peter MaydellIn gicv3_init_cpuif() we copy the ARMCPU gicv3_maintenance_interrupt into the GICv3CPUState struct's maintenance_irq field. This will only work if the board happens to have already wired up the CPU maintenance IRQ before the GIC was realized. Unfortunately this is not the case for the 'virt' board, and so the value that gets copied is NULL (since a qemu_irq is really a pointer to an IRQState struct under the hood). The effect is that the CPU interface code never actually raises the maintenance interrupt line.
Instead, since the GICv3CPUState has a pointer to the CPUState, make the dereference at the point where we want to raise the interrupt, to avoid an implicit requirement on board code to wire things up in a particular order.
---
QEMU's implementation here is a bit odd because we've put all the logic into the "GIC" device where in real hardware it's split between a GIC device and the CPU interface part in the CPU. If we had arranged it in that way then we wouldn't have this odd bit of code where the GIC device needs to raise an IRQ line that belongs to the CPU.
Not sure why we've never noticed this bug previously with KVM as a guest, you'd think we'd have spotted "maintenance interrupts just don't work"...
--- include/hw/intc/arm_gicv3_common.h | 1 - hw/intc/arm_gicv3_cpuif.c | 5 ++--- 2 files changed, 2 insertions(+), 4 deletions(-)
include/hw/intc/arm_gicv3_common.h +0 -1
@@ -153,7 +153,6 @@ struct GICv3CPUState {qemu_irq parent_fiq;qemu_irq parent_virq;qemu_irq parent_vfiq; -qemu_irq maintenance_irq;/* Redistributor */ uint32_t level;/* Current IRQ level */
hw/intc/arm_gicv3_cpuif.c +2 -3
@@ -399,6 +399,7 @@ static void gicv3_cpuif_virt_update(GICv3CPUState *cs)int irqlevel =0 ;int fiqlevel =0 ;int maintlevel =0 ; +ARMCPU *cpu =ARM_CPU (cs->cpu); idx =hppvi_index (cs);trace_gicv3_cpuif_virt_update (gicv3_redist_affid (cs), idx);
@@ -424,7 +425,7 @@ static void gicv3_cpuif_virt_update(GICv3CPUState *cs)qemu_set_irq (cs->parent_vfiq, fiqlevel);qemu_set_irq (cs->parent_virq, irqlevel); -qemu_set_irq (cs->maintenance_irq, maintlevel); +qemu_set_irq (cpu->gicv3_maintenance_interrupt, maintlevel); }static uint64_t icv_ap_read (CPUARMState *env,const ARMCPRegInfo *ri)
@@ -2624,8 +2625,6 @@ void gicv3_init_cpuif(GICv3State *s) && cpu->gic_num_lrs) {int j; - cs->maintenance_irq = cpu->gicv3_maintenance_interrupt; - cs->num_list_regs = cpu->gic_num_lrs; cs->vpribits = cpu->gic_vpribits; cs->vprebits = cpu->gic_vprebits;
Signature · 1 line
2.20.1
PATCH 1/1 hw/arm/nrf51_soc: Set system_clock_scale
In reply to Peter MaydellThe nrf51 SoC model wasn't setting the system_clock_scale global.which meant that if guest code used the systick timer in "use the processor clock" mode it would hang because time never advances.
Set the global to match the documented CPU clock speed for this SoC.
This SoC in fact doesn't have a SysTick timer (which is the only thing currently that cares about the system_clock_scale), because it's a configurable option in the Cortex-M0. However our Cortex-M0 and thus our nrf51 and our micro:bit board do provide a SysTick, so we ought to provide a functional one rather than a broken one.
---
Tested with 'make check'/'make check-acceptance' only.
hw/arm/nrf51_soc.c | 5 +++++ 1 file changed, 5 insertions(+)
hw/arm/nrf51_soc.c +5 -0
@@ -32,6 +32,9 @@#define BASE_TO_IRQ (base) ((base >> 12) & 0x1F) +/* HCLK (the main CPU clock) on this SoC is always 16MHz */ +#define HCLK_FRQ 16000000 +static uint64_t clock_read (void *opaque,hwaddr addr,unsigned int size) { qemu_log_mask(LOG_UNIMP, "%s: 0x%" HWADDR_PRIx " [%u]\n",
@@ -65,6 +68,8 @@ static void nrf51_soc_realize(DeviceState *dev_soc, Error **errp)return ; } + system_clock_scale =NANOSECONDS_PER_SECOND /HCLK_FRQ ; +object_property_set_link (OBJECT (&s->cpu),"memory" ,OBJECT (&s->container), &error_abort);if (!sysbus_realize (SYS_BUS_DEVICE (&s->cpu), errp)) {
Signature · 1 line
2.20.1
PATCH 1/1 meson.build: Don't look for libudev for static builds
In reply to Peter Maydellcommit f01496a314d916 moved the logic for detecting libudev from configure to meson.build, but in the process it dropped the condition that meant we only ask pkg-config about libudev for a non-static build.
This breaks static builds of the system emulators on at least Ubuntu 18.04.4, because on that host there is no static libudev but pkg-config still claims it exists.
Reinstate the logic that we had in the configure check.
---
We could certainly do something cleverer here, but basic "convert from configure to meson" should in general not also be changing the detection logic IMHO. We can make the logic smarter as a follow-on patch if desired.
--- meson.build | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
meson.build +1 -1
@@ -271,7 +271,7 @@ if 'CONFIG_CURL' in config_host link_args: config_host['CURL_LIBS'].split()) endif libudev = not_found -if targetos == 'linux' and (have_system or have_tools) +if targetos == 'linux' and (have_system or have_tools) and not enable_static libudev = dependency('libudev', required: get_option('mpath').enabled(), static: enable_static)
Signature · 1 line
2.20.1
PATCH 1/1 target/arm: Delete unused ARM_FEATURE_CRC
In reply to Peter MaydellIn commit 962fcbf2efe57231a9f5df we converted the uses of the ARM_FEATURE_CRC bit to use the aa32_crc32 isar_feature test instead. However we forgot to remove the now-unused definition of the feature name in the enum. Delete it now.
--- target/arm/cpu.h | 1 - 1 file changed, 1 deletion(-)
target/arm/cpu.h +0 -1
@@ -1950,7 +1950,6 @@ enum arm_features {ARM_FEATURE_V8 ,ARM_FEATURE_AARCH64 ,/* supports 64 bit mode */ ARM_FEATURE_CBAR ,/* has cp15 CBAR */ -ARM_FEATURE_CRC ,/* ARMv8 CRC instructions */ ARM_FEATURE_CBAR_RO ,/* has cp15 CBAR and it is read-only */ ARM_FEATURE_EL2 ,/* has EL2 Virtualization support */ ARM_FEATURE_EL3, /* has EL3 Secure monitor support */
Signature · 1 line
2.20.1
PATCH 1/1 target/arm: Delete unused VFP_DREG macros
In reply to Peter MaydellAs part of the Neon decodetree conversion we removed all the uses of the VFP_DREG macros, but forgot to remove the macro definitions. Do so now.
--- target/arm/translate.c | 15 --------------- 1 file changed, 15 deletions(-)
target/arm/translate.c +0 -15
@@ -2471,21 +2471,6 @@ static int disas_dsp_insn(DisasContext *s, uint32_t insn)return 1 ; } -#define VFP_REG_SHR (x, n) (((n) > 0) ? (x) >> (n) : (x) << -(n)) -#define VFP_DREG (reg, insn, bigbit, smallbit) do { \ - if (dc_isar_feature(aa32_simd_r32, s)) { \ - reg = (((insn) >> (bigbit)) & 0x0f) \ - | (((insn) >> ((smallbit) - 4)) & 0x10); \ - } else { \ - if (insn & (1 << (smallbit))) \ - return 1; \ - reg = ((insn) >> (bigbit)) & 0x0f; \ - }} while (0) - -#define VFP_DREG_D (reg, insn) VFP_DREG(reg, insn, 12, 22) -#define VFP_DREG_N (reg, insn) VFP_DREG(reg, insn, 16, 7) -#define VFP_DREG_M (reg, insn) VFP_DREG(reg, insn, 0, 5) -static inline bool use_goto_tb (DisasContext *s,target_ulong dest) {#ifndef CONFIG_USER_ONLY
Signature · 1 line
2.20.1
PATCH 1/1 linux-user/arm/signal.c: Drop TARGET_CONFIG_CPU_32
In reply to Peter MaydellThe Arm signal-handling code has some parts ifdeffed with a TARGET_CONFIG_CPU_32, which is always defined. This is a leftover from when this code's structure was based on the Linux kernel signal handling code, where it was intended to support 26-bit Arm CPUs. The kernel dropped its CONFIG_CPU_32 in kernel commit 4da8b8208eded0ba21e3 in 2009.
QEMU has never had 26-bit CPU support and is unlikely to ever add it; we certainly aren't going to support 26-bit Linux binaries via linux-user mode. The ifdef is just unhelpful noise, so remove it entirely.
---
Based-on: <[email protected]> ("[PATCH v2] target/arm: Allow user-mode code to write CPSR.E via MSR") to avoid a textual conflict.
linux-user/arm/signal.c | 6 ------ 1 file changed, 6 deletions(-)
linux-user/arm/signal.c +0 -6
@@ -126,8 +126,6 @@ struct rt_sigframe_v2abi_ulong retcode[4 ]; }; -#define TARGET_CONFIG_CPU_32 1 -/* * For ARM syscalls, we encode the syscall number into the instruction. */
@@ -187,9 +185,7 @@ setup_sigcontext(struct target_sigcontext *sc, /*struct _fpstate *fpstate,*/__put_user (env->regs[13 ], &sc->arm_sp);__put_user (env->regs[14 ], &sc->arm_lr);__put_user (env->regs[15 ], &sc->arm_pc); -#ifdef TARGET_CONFIG_CPU_32 __put_user (cpsr_read (env), &sc->arm_cpsr); -#endif __put_user (/* current->thread.trap_no */ 0 , &sc->trap_no);__put_user (/* current->thread.error_code */ 0 , &sc->error_code);
@@ -549,11 +545,9 @@ restore_sigcontext(CPUARMState *env, struct target_sigcontext *sc)__get_user (env->regs[13 ], &sc->arm_sp);__get_user (env->regs[14 ], &sc->arm_lr);__get_user (env->regs[15 ], &sc->arm_pc); -#ifdef TARGET_CONFIG_CPU_32 __get_user (cpsr, &sc->arm_cpsr);cpsr_write (env, cpsr,CPSR_USER |CPSR_EXEC , CPSRWriteByInstr);arm_rebuild_hflags (env); -#endif err |= !valid_user_regs (env);
Signature · 1 line
2.20.1
PATCH v2 1/1 target/arm: Allow user-mode code to write CPSR.E via MSR
In reply to Peter MaydellUsing the MSR instruction to write to CPSR.E is deprecated, but it is required to work from any mode including unprivileged code. We were incorrectly forbidding usermode code from writing it because CPSR_USER did not include the CPSR_E bit.
We use CPSR_USER in only three places:
* as the mask of what to allow userspace MSR to write to CPSR
* when deciding what bits a linux-user signal-return should be able to write from the sigcontext structure
* in target_user_copy_regs() when we set up the initial registers for the linux-user process
In the first two cases not being able to update CPSR.E is a bug, and in the third case it doesn't matter because CPSR.E is always 0 there. So we can fix both bugs by adding CPSR_E to CPSR_USER.
Because the cpsr_write() in restore_sigcontext() is now changing a CPSR bit which is cached in hflags, we need to add an arm_rebuild_hflags() call there; the callsite in target_user_copy_regs() was already rebuilding hflags for other reasons.
(The recommended way to change CPSR.E is to use the 'SETEND' instruction, which we do correctly allow from usermode code.)
---
v2 changes:
* fixed wrong variable name in commit message
* added arm_rebuild_hflags() call in restore_sigcontext()
--- target/arm/cpu.h | 2 +- linux-user/arm/signal.c | 1 + 2 files changed, 2 insertions(+), 1 deletion(-)
target/arm/cpu.h +1 -1
@@ -1230,7 +1230,7 @@ void pmu_init(ARMCPU *cpu);#define CACHED_CPSR_BITS (CPSR_T | CPSR_AIF | CPSR_GE | CPSR_IT | CPSR_Q \ | CPSR_NZCV)/* Bits writable in user mode. */ -#define CPSR_USER (CPSR_NZCV | CPSR_Q | CPSR_GE) +#define CPSR_USER (CPSR_NZCV | CPSR_Q | CPSR_GE | CPSR_E)/* Execution state bits. MRS read as zero, MSR writes ignored. */ #define CPSR_EXEC (CPSR_T | CPSR_IT | CPSR_J | CPSR_IL)
linux-user/arm/signal.c +1 -0
@@ -552,6 +552,7 @@ restore_sigcontext(CPUARMState *env, struct target_sigcontext *sc)#ifdef TARGET_CONFIG_CPU_32 __get_user (cpsr, &sc->arm_cpsr);cpsr_write (env, cpsr,CPSR_USER |CPSR_EXEC , CPSRWriteByInstr); +arm_rebuild_hflags (env);#endif err |= !valid_user_regs (env);
Signature · 1 line
2.20.1
PATCH 1/1 osdep.h: Add doc comment for qemu_get_thread_id()
In reply to Peter MaydellAdd a documentation comment for qemu_get_thread_id(): since this is rather host-OS-specific it's useful if people writing the implementation and people thinking of using the function know what the purpose and limitations are.
---
Based on conversation with Dan on IRC, and prompted by the recent patch to add OpenBSD support.
Q: should we document exactly what the thread-id value is for each host platform in the QMP documentation ? Somebody writing a management layer app should ideally not have to grovel through the application to figure out what they should do with the integer value they get back from query-cpus...
include/qemu/osdep.h | 14 ++++++++++++++ 1 file changed, 14 insertions(+)
include/qemu/osdep.h +14 -0
@@ -515,6 +515,20 @@ bool qemu_has_ofd_lock(void);bool qemu_write_pidfile (const char *pidfile,Error **errp); +/** +* qemu_get_thread_id: Return OS-specific ID of current thread +* +* This function returns an OS-specific identifier of the +* current thread. This will be used for the "thread-id" field in +* the response to the QMP query-cpus and query-iothreads commands. +* The intention is that a VM management layer application can then +* use it to tie specific QEMU vCPU and IO threads to specific host +* CPUs using whatever the host OS's CPU affinity setting API is. +* New implementations of this function for new host OSes should +* return the most sensible integer ID that works for that purpose. +* +* This function should not be used for anything else inside QEMU. +*/ int qemu_get_thread_id (void );#ifndef CONFIG_IOVEC
Signature · 1 line
2.20.1
PATCH 1/1 net/tap-solaris.c: Include qemu-common.h for TFR macro
In reply to Peter MaydellIn commit a8d2532645cf5ce4 we cleaned up usage of the qemu-common.h header so that it was always included from .c files and never from other .h files. We missed adding it to net/tap-solaris.c (which previously was pulling it in via tap-int.h), which broke building on Solaris hosts.
---
Untested: Michele, could you give this a try?
--- net/tap-solaris.c | 1 + 1 file changed, 1 insertion(+)
net/tap-solaris.c +1 -0
@@ -27,6 +27,7 @@#include "tap_int.h" #include "qemu/ctype.h" #include "qemu/cutils.h" +#include "qemu-common.h" #include <sys/ethernet.h> #include <sys/sockio.h>
Signature · 1 line
2.20.1