Skip to contentSkip to conversation

Extend peci feature

PATCH In review Billy Tsai 3 participants 6 messages Oct 16, 2020 – Oct 28, 2020

Subsystems (4)
lore
Share & tools
lore

Billy Tsai

author reviewer
#0 lore raw

cover Extend peci feature

This patch series extend the peci to support 64byte mode and simplify the setting of peci operation rate.

Billy Tsai (3):
peci: aspeed: make the driver support 64byte mode
peci: aspeed: Auto calculate the adapter divisor
dt-bindings: Change the meaning of clock-frequency

 .../devicetree/bindings/peci/peci-aspeed.yaml |  56 +++----
 arch/arm/boot/dts/aspeed-g6.dtsi              |   4 +-
 drivers/peci/busses/peci-aspeed.c             | 158 ++++++++++++------
 3 files changed, 136 insertions(+), 82 deletions(-)
Signature · 1 line
2.17.1
author reviewer
#1 lore raw

PATCH 1/3 peci: aspeed: make the driver support 64byte mode

At ast2600 peci add the new feature can support the transfer size up to 64 bytes.
We can use the dts property "64byte-mode" to enable it.

---
 drivers/peci/busses/peci-aspeed.c | 67 +++++++++++++++++++++++++------
 1 file changed, 55 insertions(+), 12 deletions(-)
drivers/peci/busses/peci-aspeed.c +55 -12
index 2673d4c4dcf9..d6039b1c4494 100644
@@ -28,6 +28,9 @@
 #define   ASPEED_PECI_CTRL_INVERT_IN		BIT(6)
 #define   ASPEED_PECI_CTRL_BUS_CONTENT_EN	BIT(5)
 #define   ASPEED_PECI_CTRL_PECI_EN		BIT(4)
+#define   ASPEED_PECI_CTRL_64BYTE_MODE_EN	BIT(1)
+#define     ASPEED_PECI_32BYTE_MODE		0
+#define     ASPEED_PECI_64BYTE_MODE		1
 #define   ASPEED_PECI_CTRL_PECI_CLK_EN		BIT(0)
 
 /* Timing Negotiation Register */
@@ -79,7 +82,7 @@
 #define   ASPEED_PECI_INT_TIMING_RESULT_MASK	GENMASK(29, 16)
 	  /* bits[4..0]: Same bit fields in the 'Interrupt Register' */
 
-/* Rx/Tx Data Buffer Registers */
+/* 32Bytes mode: Rx/Tx Data Buffer Registers */
 #define ASPEED_PECI_W_DATA0			0x20
 #define ASPEED_PECI_W_DATA1			0x24
 #define ASPEED_PECI_W_DATA2			0x28
@@ -96,7 +99,39 @@
 #define ASPEED_PECI_R_DATA5			0x54
 #define ASPEED_PECI_R_DATA6			0x58
 #define ASPEED_PECI_R_DATA7			0x5c
-#define   ASPEED_PECI_DATA_BUF_SIZE_MAX		32
+/* 64Bytes mode: Rx/Tx Data Buffer Registers */
+#define ASPEED_PECI_64B_W_DATA0  0x80
+#define ASPEED_PECI_64B_W_DATA1  0x84
+#define ASPEED_PECI_64B_W_DATA2  0x88
+#define ASPEED_PECI_64B_W_DATA3  0x8C
+#define ASPEED_PECI_64B_W_DATA4  0x90
+#define ASPEED_PECI_64B_W_DATA5  0x94
+#define ASPEED_PECI_64B_W_DATA6  0x98
+#define ASPEED_PECI_64B_W_DATA7  0x9C
+#define ASPEED_PECI_64B_W_DATA8  0xA0
+#define ASPEED_PECI_64B_W_DATA9  0xA4
+#define ASPEED_PECI_64B_W_DATAA  0xA8
+#define ASPEED_PECI_64B_W_DATAB  0xAC
+#define ASPEED_PECI_64B_W_DATAC  0xB0
+#define ASPEED_PECI_64B_W_DATAD  0xB4
+#define ASPEED_PECI_64B_W_DATAE  0xB8
+#define ASPEED_PECI_64B_W_DATAF  0xBC
+#define ASPEED_PECI_64B_R_DATA0  0xC0
+#define ASPEED_PECI_64B_R_DATA1  0xC4
+#define ASPEED_PECI_64B_R_DATA2  0xC8
+#define ASPEED_PECI_64B_R_DATA3  0xCC
+#define ASPEED_PECI_64B_R_DATA4  0xD0
+#define ASPEED_PECI_64B_R_DATA5  0xD4
+#define ASPEED_PECI_64B_R_DATA6  0xD8
+#define ASPEED_PECI_64B_R_DATA7  0xDC
+#define ASPEED_PECI_64B_R_DATA8  0xE0
+#define ASPEED_PECI_64B_R_DATA9  0xE4
+#define ASPEED_PECI_64B_R_DATAA  0xE8
+#define ASPEED_PECI_64B_R_DATAB  0xEC
+#define ASPEED_PECI_64B_R_DATAC  0xF0
+#define ASPEED_PECI_64B_R_DATAD  0xF4
+#define ASPEED_PECI_64B_R_DATAE  0xF8
+#define ASPEED_PECI_64B_R_DATAF  0xFC
 
 /* Timing Negotiation */
 #define ASPEED_PECI_RD_SAMPLING_POINT_DEFAULT	8
@@ -125,6 +160,8 @@ struct aspeed_peci {
 	struct completion	xfer_complete;
 	u32			status;
 	u32			cmd_timeout_ms;
+	/* 0: older 32 bytes, 1 : 64bytes mode */
+	int			xfer_mode;
 };
 
 static inline int aspeed_peci_check_idle(struct aspeed_peci *priv)
@@ -144,12 +181,13 @@ static int aspeed_peci_xfer(struct peci_adapter *adapter,
 	struct aspeed_peci *priv = peci_get_adapdata(adapter);
 	long err, timeout = msecs_to_jiffies(priv->cmd_timeout_ms);
 	u32 peci_head, peci_state, rx_data = 0;
+	u32 max_buffer_size = (priv->xfer_mode) ? 64 : 32;
 	ulong flags;
 	int i, ret;
 	uint reg;
 
-	if (msg->tx_len > ASPEED_PECI_DATA_BUF_SIZE_MAX ||
-	    msg->rx_len > ASPEED_PECI_DATA_BUF_SIZE_MAX)
+	if (msg->tx_len > max_buffer_size ||
+	    msg->rx_len > max_buffer_size)
 		return -EINVAL;
 
 	/* Check command sts and bus idle state */
@@ -167,8 +205,11 @@ static int aspeed_peci_xfer(struct peci_adapter *adapter,
 	writel(peci_head, priv->base + ASPEED_PECI_RW_LENGTH);
 
 	for (i = 0; i < msg->tx_len; i += 4) {
-		reg = i < 16 ? ASPEED_PECI_W_DATA0 + i % 16 :
-			       ASPEED_PECI_W_DATA4 + i % 16;
+		if (priv->xfer_mode)
+			reg = ASPEED_PECI_64B_W_DATA0 + i % 16;
+		else
+			reg = i < 16 ? ASPEED_PECI_W_DATA0 + i % 16 :
+				       ASPEED_PECI_W_DATA4 + i % 16;
 		writel(le32_to_cpup((__le32 *)&msg->tx_buf[i]),
 		       priv->base + reg);
 	}
@@ -215,8 +256,11 @@ static int aspeed_peci_xfer(struct peci_adapter *adapter,
 		u8 byte_offset = i % 4;
 
 		if (byte_offset == 0) {
-			reg = i < 16 ? ASPEED_PECI_R_DATA0 + i % 16 :
-				       ASPEED_PECI_R_DATA4 + i % 16;
+			if (priv->xfer_mode)
+				reg = ASPEED_PECI_64B_R_DATA0 + i % 16;
+			else
+				reg = i < 16 ? ASPEED_PECI_R_DATA0 + i % 16 :
+					ASPEED_PECI_R_DATA4 + i % 16;
 			rx_data = readl(priv->base + reg);
 		}
 
@@ -349,10 +393,8 @@ static int aspeed_peci_init_ctrl(struct aspeed_peci *priv)
 		priv->cmd_timeout_ms = ASPEED_PECI_CMD_TIMEOUT_MS_DEFAULT;
 	}
 
-	writel(FIELD_PREP(ASPEED_PECI_CTRL_CLK_DIV_MASK,
-			  ASPEED_PECI_CLK_DIV_DEFAULT) |
-	       ASPEED_PECI_CTRL_PECI_CLK_EN, priv->base + ASPEED_PECI_CTRL);
-
+	if (of_property_read_bool(priv->dev->of_node, "64byte-mode"))
+		priv->xfer_mode = 1;
 	/*
 	 * Timing negotiation period setting.
 	 * The unit of the programmed value is 4 times of PECI clock period.
@@ -373,6 +415,7 @@ static int aspeed_peci_init_ctrl(struct aspeed_peci *priv)
 	/* Read sampling point and clock speed setting */
 	writel(FIELD_PREP(ASPEED_PECI_CTRL_SAMPLING_MASK, rd_sampling_point) |
 	       FIELD_PREP(ASPEED_PECI_CTRL_CLK_DIV_MASK, clk_div_val) |
+	       (priv->xfer_mode ? ASPEED_PECI_CTRL_64BYTE_MODE_EN : 0) |
 	       ASPEED_PECI_CTRL_PECI_EN | ASPEED_PECI_CTRL_PECI_CLK_EN,
 	       priv->base + ASPEED_PECI_CTRL);
 
Signature · 1 line
2.17.1
author reviewer
#2 lore raw

PATCH 2/3 peci: aspeed: Auto calculate the adapter divisor

In reply to Billy Tsai

This pach change the meaning of clk-frequency property from original controller clock to bit frequency of peci negotiation stage and auto calculate the adapter divisor setting to close aim.
The expected frequency and real frequency may have errors because of the granularities of the divisor.

---
 arch/arm/boot/dts/aspeed-g6.dtsi  |  4 +-
 drivers/peci/busses/peci-aspeed.c | 91 ++++++++++++++++++-------------
 2 files changed, 53 insertions(+), 42 deletions(-)
arch/arm/boot/dts/aspeed-g6.dtsi +1 -3
index cb053a996e87..6e1e5b5733e6 100644
@@ -750,9 +750,7 @@
 		interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&syscon ASPEED_CLK_GATE_REF0CLK>;
 		resets = <&syscon ASPEED_RESET_PECI>;
-		clock-frequency = <24000000>;
-		msg-timing = <1>;
-		addr-timing = <1>;
+		clock-frequency = <1000000>;
 		rd-sampling-point = <8>;
 		cmd-timeout-ms = <1000>;
 		status = "disabled";
drivers/peci/busses/peci-aspeed.c +52 -39

115 lines not on this page · raw message

Signature · 1 line
2.17.1
maintainer
#3 lore raw

Re: [PATCH 2/3] peci: aspeed: Auto calculate the adapter divisor

Hi Billy,

Quoted 6 lines · Billy Tsai

This pach change the meaning of clk-frequency property from original controller clock to bit frequency of peci negotiation stage and auto calculate the adapter divisor setting to close aim.
The expected frequency and real frequency may have errors because of the granularities of the divisor.

This patch can't go to the mainline lists as the authors (Intel) have not yet had it merged.

Cheers,

Joel

Quoted 147 lines
---
 arch/arm/boot/dts/aspeed-g6.dtsi  |  4 +-
 drivers/peci/busses/peci-aspeed.c | 91 ++++++++++++++++++-------------
 2 files changed, 53 insertions(+), 42 deletions(-)
arch/arm/boot/dts/aspeed-g6.dtsi +1 -3
index cb053a996e87..6e1e5b5733e6 100644
@@ -750,9 +750,7 @@
                interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
                clocks = <&syscon ASPEED_CLK_GATE_REF0CLK>;
                resets = <&syscon ASPEED_RESET_PECI>;
-               clock-frequency = <24000000>;
-               msg-timing = <1>;
-               addr-timing = <1>;
+               clock-frequency = <1000000>;
                rd-sampling-point = <8>;
                cmd-timeout-ms = <1000>;
                status = "disabled";
drivers/peci/busses/peci-aspeed.c +52 -40
index d6039b1c4494..9e7c7582e4bb 100644
@@ -133,6 +133,11 @@
 #define ASPEED_PECI_64B_R_DATAE  0xF8
 #define ASPEED_PECI_64B_R_DATAF  0xFC
 
+/* Bus Frequency */
+#define ASPEED_PECI_BUS_FREQ_MAX       2000000
+#define ASPEED_PECI_BUS_FREQ_MIN       2000
+#define ASPEED_PECI_BUS_FREQ_DEFAULT   1000000
+
 /* Timing Negotiation */
 #define ASPEED_PECI_RD_SAMPLING_POINT_DEFAULT  8
 #define ASPEED_PECI_RD_SAMPLING_POINT_MAX      15
@@ -324,51 +329,47 @@ static irqreturn_t aspeed_peci_irq_handler(int irq, void *arg)
 static int aspeed_peci_init_ctrl(struct aspeed_peci *priv)
 {
        u32 msg_timing, addr_timing, rd_sampling_point;
-       u32 clk_freq, clk_divisor, clk_div_val = 0;
+       u32 clk_freq, clk_div_val = 0;
+       u32 msg_timing_idx, clk_div_val_idx;
+       int delta_value, delta_tmp, clk_divisor, clk_divisor_tmp;
        int ret;
 
-       priv->clk = devm_clk_get(priv->dev, NULL);
-       if (IS_ERR(priv->clk)) {
-               dev_err(priv->dev, "Failed to get clk source.\n");
-               return PTR_ERR(priv->clk);
-       }
-
-       ret = clk_prepare_enable(priv->clk);
-       if (ret) {
-               dev_err(priv->dev, "Failed to enable clock.\n");
-               return ret;
-       }
-
        ret = device_property_read_u32(priv->dev, "clock-frequency", &clk_freq);
-       if (ret) {
-               dev_err(priv->dev,
-                       "Could not read clock-frequency property.\n");
-               clk_disable_unprepare(priv->clk);
-               return ret;
-       }
-
-       clk_divisor = clk_get_rate(priv->clk) / clk_freq;
-
-       while ((clk_divisor >> 1) && (clk_div_val < ASPEED_PECI_CLK_DIV_MAX))
-               clk_div_val++;
-
-       ret = device_property_read_u32(priv->dev, "msg-timing", &msg_timing);
-       if (ret || msg_timing > ASPEED_PECI_MSG_TIMING_MAX) {
+       if (ret ||
+       clk_freq > ASPEED_PECI_BUS_FREQ_MAX ||
+       clk_freq < ASPEED_PECI_BUS_FREQ_MIN) {
                if (!ret)
                        dev_warn(priv->dev,
-                                "Invalid msg-timing : %u, Use default : %u\n",
-                                msg_timing, ASPEED_PECI_MSG_TIMING_DEFAULT);
-               msg_timing = ASPEED_PECI_MSG_TIMING_DEFAULT;
-       }
-
-       ret = device_property_read_u32(priv->dev, "addr-timing", &addr_timing);
-       if (ret || addr_timing > ASPEED_PECI_ADDR_TIMING_MAX) {
-               if (!ret)
-                       dev_warn(priv->dev,
-                                "Invalid addr-timing : %u, Use default : %u\n",
-                                addr_timing, ASPEED_PECI_ADDR_TIMING_DEFAULT);
-               addr_timing = ASPEED_PECI_ADDR_TIMING_DEFAULT;
+                                "Invalid clock-frequency : %u, Use default : %u\n",
+                                clk_freq, ASPEED_PECI_BUS_FREQ_DEFAULT);
+               clk_freq = ASPEED_PECI_BUS_FREQ_DEFAULT;
        }
+       /*
+        * PECI bus clock = (Ref. clk) / (1 << PECI00[10:8])
+        * PECI operation clock = (PECI bus clock)/ 4*(PECI04[15:8]*4+1)
+        * (1 << PECI00[10:8]) * (PECI04[15:8]*4+1) =
+        * (Ref. clk) / (4 * PECI operation clock)
+        */
+       clk_divisor = clk_get_rate(priv->clk) / (4*clk_freq);
+       delta_value = clk_divisor;
+       /* Find the closest divisor for clock-frequency */
+       for (msg_timing_idx = 1; msg_timing_idx <= 255; msg_timing_idx++)
+               for (clk_div_val_idx = 0; clk_div_val_idx < 7;
+                       clk_div_val_idx++) {
+                       clk_divisor_tmp = (1 << clk_div_val_idx) *
+                                       (msg_timing_idx * 4 + 1);
+                       delta_tmp = abs(clk_divisor - clk_divisor_tmp);
+                       if (delta_tmp < delta_value) {
+                               delta_value = delta_tmp;
+                               msg_timing = msg_timing_idx;
+                               clk_div_val = clk_div_val_idx;
+                       }
+               }
+       addr_timing = msg_timing;
+       dev_info(priv->dev, "Expect frequency: %d Real frequency is about: %lu",
+               clk_freq,
+               clk_get_rate(priv->clk) /
+               (4 * (1 << clk_div_val) * (msg_timing * 4 + 1)));
 
        ret = device_property_read_u32(priv->dev, "rd-sampling-point",
                                       &rd_sampling_point);
@@ -463,6 +464,18 @@ static int aspeed_peci_probe(struct platform_device *pdev)
        priv->adapter->xfer = aspeed_peci_xfer;
        priv->adapter->use_dma = false;
 
+       priv->clk = devm_clk_get(priv->dev, NULL);
+       if (IS_ERR(priv->clk)) {
+               dev_err(priv->dev, "Failed to get clk source.\n");
+               return PTR_ERR(priv->clk);
+       }
+
+       ret = clk_prepare_enable(priv->clk);
+       if (ret) {
+               dev_err(priv->dev, "Failed to enable clock.\n");
+               return ret;
+       }
+
        priv->rst = devm_reset_control_get(&pdev->dev, NULL);
        if (IS_ERR(priv->rst)) {
                dev_err(&pdev->dev,
--

2.17.1

author reviewer
#4 lore raw

PATCH 3/3 dt-bindings: Change the meaning of clock-frequency

In reply to Billy Tsai

Integration of the usage of msg-timing and addr-timing to clock-frequency. User can just set it to adjust the peci work efficient.

---
 .../devicetree/bindings/peci/peci-aspeed.yaml | 56 +++++++++----------
 1 file changed, 28 insertions(+), 28 deletions(-)
Documentation/devicetree/bindings/peci/peci-aspeed.yaml +28 -28
index 0f5c2993fe9b..7c6c895784af 100644
@@ -40,31 +40,33 @@ properties:
     maxItems: 1
 
   clock-frequency:
-    # Operation frequency of PECI controller in units of Hz.
-    minimum: 187500
-    maximum: 24000000
-
-  msg-timing:
-    description: |
-      Message timing negotiation period. This value will determine the period
-      of message timing negotiation to be issued by PECI controller. The unit
-      of the programmed value is four times of PECI clock period.
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32
-      - minimum: 0
-        maximum: 255
-        default: 1
-
-  addr-timing:
-    description: |
-      Address timing negotiation period. This value will determine the period
-      of address timing negotiation to be issued by PECI controller. The unit
-      of the programmed value is four times of PECI clock period.
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32
-      - minimum: 0
-        maximum: 255
-        default: 1
+    # The bit frequency of PECI negotiation stage in units of Hz.
+    # Driver will calculate the best divisor setting of msg-timing and
+    # addr-timing to meet the value.
+    minimum: 2000
+    maximum: 2000000
+
+  # msg-timing:
+  #   description: |
+  #     Message timing negotiation period. This value will determine the period
+  #     of message timing negotiation to be issued by PECI controller. The unit
+  #     of the programmed value is four times of PECI clock period.
+  #   allOf:
+  #     - $ref: /schemas/types.yaml#/definitions/uint32
+  #     - minimum: 0
+  #       maximum: 255
+  #       default: 1
+
+  # addr-timing:
+  #   description: |
+  #     Address timing negotiation period. This value will determine the period
+  #     of address timing negotiation to be issued by PECI controller. The unit
+  #     of the programmed value is four times of PECI clock period.
+  #   allOf:
+  #     - $ref: /schemas/types.yaml#/definitions/uint32
+  #     - minimum: 0
+  #       maximum: 255
+  #       default: 1
 
   rd-sampling-point:
     description: |
@@ -114,9 +116,7 @@ examples:
             interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
             clocks = <&syscon ASPEED_CLK_GATE_REF0CLK>;
             resets = <&syscon ASPEED_RESET_PECI>;
-            clock-frequency = <24000000>;
-            msg-timing = <1>;
-            addr-timing = <1>;
+            clock-frequency = <2000000>;
             rd-sampling-point = <8>;
             cmd-timeout-ms = <1000>;
         };
Signature · 1 line
2.17.1
maintainer
#5 lore raw

Re: [PATCH 3/3] dt-bindings: Change the meaning of clock-frequency

Quoted 2 lines · Billy Tsai

Integration of the usage of msg-timing and addr-timing to clock-frequency. User can just set it to adjust the peci work efficient.

You're breaking the ABI changing this.

Quoted 32 lines
---
 .../devicetree/bindings/peci/peci-aspeed.yaml | 56 +++++++++----------
 1 file changed, 28 insertions(+), 28 deletions(-)
Documentation/devicetree/bindings/peci/peci-aspeed.yaml +0 -18
index 0f5c2993fe9b..7c6c895784af 100644
@@ -40,31 +40,33 @@ properties:
     maxItems: 1
 
   clock-frequency:
-    # Operation frequency of PECI controller in units of Hz.
-    minimum: 187500
-    maximum: 24000000
-
-  msg-timing:
-    description: |
-      Message timing negotiation period. This value will determine the period
-      of message timing negotiation to be issued by PECI controller. The unit
-      of the programmed value is four times of PECI clock period.
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32
-      - minimum: 0
-        maximum: 255
-        default: 1
-
-  addr-timing:
-    description: |
-      Address timing negotiation period. This value will determine the period

Documentation/devicetree/bindings/peci/peci-aspeed.yaml properties: · line 45

Quoted 10 lines
Documentation/devicetree/bindings/peci/peci-aspeed.yaml +3 -7
-      of address timing negotiation to be issued by PECI controller. The unit
-      of the programmed value is four times of PECI clock period.
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32
-      - minimum: 0
-        maximum: 255
-        default: 1
+    # The bit frequency of PECI negotiation stage in units of Hz.
+    # Driver will calculate the best divisor setting of msg-timing and
+    # addr-timing to meet the value.

Use 'description' rather than comments.

Documentation/devicetree/bindings/peci/peci-aspeed.yaml properties: · line 58

Quoted 13 lines
Documentation/devicetree/bindings/peci/peci-aspeed.yaml +13 -0
+    minimum: 2000
+    maximum: 2000000
+
+  # msg-timing:
+  #   description: |
+  #     Message timing negotiation period. This value will determine the period
+  #     of message timing negotiation to be issued by PECI controller. The unit
+  #     of the programmed value is four times of PECI clock period.
+  #   allOf:
+  #     - $ref: /schemas/types.yaml#/definitions/uint32
+  #     - minimum: 0
+  #       maximum: 255
+  #       default: 1

Why is this commented out?

Quoted 28 lines
Documentation/devicetree/bindings/peci/peci-aspeed.yaml +12 -3
+
+  # addr-timing:
+  #   description: |
+  #     Address timing negotiation period. This value will determine the period
+  #     of address timing negotiation to be issued by PECI controller. The unit
+  #     of the programmed value is four times of PECI clock period.
+  #   allOf:
+  #     - $ref: /schemas/types.yaml#/definitions/uint32
+  #     - minimum: 0
+  #       maximum: 255
+  #       default: 1
 
   rd-sampling-point:
     description: |
@@ -114,9 +116,7 @@ examples:
             interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
             clocks = <&syscon ASPEED_CLK_GATE_REF0CLK>;
             resets = <&syscon ASPEED_RESET_PECI>;
-            clock-frequency = <24000000>;
-            msg-timing = <1>;
-            addr-timing = <1>;
+            clock-frequency = <2000000>;
             rd-sampling-point = <8>;
             cmd-timeout-ms = <1000>;
         };
Signature · 1 line
2.17.1