Add support to handle prefetchable memory
cover Add support to handle prefetchable memory
This patch series adds support for configuring the DesignWare IP's ATU region for prefetchable memory translations.
It first starts by flagging a warning if the size of non-prefetchable aperture goes beyond 32-bit as PCIe spec doesn't allow it. And then adds required support for programming the ATU to handle higher (i.e. >4GB) sizes and then finally adds support for differentiating between prefetchable and non-prefetchable regions and configuring one of the ATU regions for prefetchable memory translations purpose.
Vidya Sagar (3):
PCI: of: Warn if non-prefetchable memory aperture size is > 32-bit
PCI: dwc: Add support to program ATU for >4GB memory aperture sizes
PCI: dwc: Add support to handle prefetchable memory mapping
.../pci/controller/dwc/pcie-designware-host.c | 39 ++++++++++++++++--- drivers/pci/controller/dwc/pcie-designware.c | 12 +++--- drivers/pci/controller/dwc/pcie-designware.h | 4 +- drivers/pci/of.c | 5 +++ 4 files changed, 48 insertions(+), 12 deletions(-)
Signature · 1 line
2.17.1
PATCH 1/3 PCI: of: Warn if non-prefetchable memory aperture size is > 32-bit
As per PCIe spec r5.0, sec 7.5.1.3.8 only 32-bit BAR registers are defined for non-prefetchable memory and hence a warning should be reported when the size of them go beyond 32-bits.
--- drivers/pci/of.c | 5 +++++ 1 file changed, 5 insertions(+)
drivers/pci/of.c +5 -0
@@ -556,6 +556,11 @@ static int pci_parse_request_of_pci_ranges(struct device *dev,break ;case IORESOURCE_MEM : res_valid |= !(res->flags &IORESOURCE_PREFETCH ); + +if (!(res->flags &IORESOURCE_PREFETCH )) +if (upper_32_bits (resource_size (res))) +dev_warn (dev,"Memory resource size exceeds max for 32 bits\n" ); +break ; } }
Signature · 1 line
2.17.1
Re: [PATCH 1/3] PCI: of: Warn if non-prefetchable memory aperture size is > 32-bit
Quoted 9 lines · Vidya Sagar
As per PCIe spec r5.0, sec 7.5.1.3.8 only 32-bit BAR registers are defined for non-prefetchable memory and hence a warning should be reported when the size of them go beyond 32-bits.
Signed-off-by Vidya Sagar <[email protected]>--- drivers/pci/of.c | 5 +++++ 1 file changed, 5 insertions(+)
PATCH 2/3 PCI: dwc: Add support to program ATU for >4GB memory aperture sizes
In reply to Vidya SagarAdd support to program the ATU to enable translations for >4GB sizes of the prefetchable memory apertures.
--- drivers/pci/controller/dwc/pcie-designware.c | 12 +++++++----- drivers/pci/controller/dwc/pcie-designware.h | 3 ++- 2 files changed, 9 insertions(+), 6 deletions(-)
drivers/pci/controller/dwc/pcie-designware.c +7 -5
@@ -228,7 +228,7 @@ static void dw_pcie_writel_ob_unroll(struct dw_pcie *pci, u32 index, u32 reg,static void dw_pcie_prog_outbound_atu_unroll (struct dw_pcie *pci,u8 func_no,int index,int type,u64 cpu_addr,u64 pci_addr, -u32 size) +u64 size) {u32 retries, val;u64 limit_addr = cpu_addr + size -1 ;
@@ -245,8 +245,10 @@ static void dw_pcie_prog_outbound_atu_unroll(struct dw_pcie *pci, u8 func_no, lower_32_bits(pci_addr));dw_pcie_writel_ob_unroll (pci, index,PCIE_ATU_UNR_UPPER_TARGET ,upper_32_bits (pci_addr)); -dw_pcie_writel_ob_unroll (pci, index,PCIE_ATU_UNR_REGION_CTRL1 , - type |PCIE_ATU_FUNC_NUM (func_no)); + val = type |PCIE_ATU_FUNC_NUM (func_no); + val =upper_32_bits (size -1 ) ? + val |PCIE_ATU_INCREASE_REGION_SIZE : val; +dw_pcie_writel_ob_unroll (pci, index,PCIE_ATU_UNR_REGION_CTRL1 , val);dw_pcie_writel_ob_unroll (pci, index,PCIE_ATU_UNR_REGION_CTRL2 ,PCIE_ATU_ENABLE );
@@ -267,7 +269,7 @@ static void dw_pcie_prog_outbound_atu_unroll(struct dw_pcie *pci, u8 func_no,static void __dw_pcie_prog_outbound_atu (struct dw_pcie *pci,u8 func_no,int index,int type,u64 cpu_addr, -u64 pci_addr,u32 size) +u64 pci_addr,u64 size) {u32 retries, val;
@@ -311,7 +313,7 @@ static void __dw_pcie_prog_outbound_atu(struct dw_pcie *pci, u8 func_no, }void dw_pcie_prog_outbound_atu (struct dw_pcie *pci,int index,int type, -u64 cpu_addr,u64 pci_addr,u32 size) +u64 cpu_addr,u64 pci_addr,u64 size) {__dw_pcie_prog_outbound_atu (pci,0 , index, type, cpu_addr, pci_addr, size);
drivers/pci/controller/dwc/pcie-designware.h +2 -1
@@ -84,6 +84,7 @@#define PCIE_ATU_REGION_INDEX1 0x1#define PCIE_ATU_REGION_INDEX0 0x0#define PCIE_ATU_CR1 0x904 +#define PCIE_ATU_INCREASE_REGION_SIZE BIT(13)#define PCIE_ATU_TYPE_MEM 0x0#define PCIE_ATU_TYPE_IO 0x2#define PCIE_ATU_TYPE_CFG0 0x4
@@ -295,7 +296,7 @@ void dw_pcie_upconfig_setup(struct dw_pcie *pci);int dw_pcie_wait_for_link (struct dw_pcie *pci);void dw_pcie_prog_outbound_atu (struct dw_pcie *pci,int index,int type,u64 cpu_addr,u64 pci_addr, -u32 size); +u64 size);void dw_pcie_prog_ep_outbound_atu (struct dw_pcie *pci,u8 func_no,int index,int type,u64 cpu_addr,u64 pci_addr,u32 size);
Signature · 1 line
2.17.1
Re: [PATCH 2/3] PCI: dwc: Add support to program ATU for >4GB memory aperture sizes
Quoted 9 lines · Vidya Sagar
Add support to program the ATU to enable translations for >4GB sizes of the prefetchable memory apertures.
Signed-off-by Vidya Sagar <[email protected]>--- drivers/pci/controller/dwc/pcie-designware.c | 12 +++++++----- drivers/pci/controller/dwc/pcie-designware.h | 3 ++- 2 files changed, 9 insertions(+), 6 deletions(-)
PATCH 3/3 PCI: dwc: Add support to handle prefetchable memory mapping
In reply to Vidya SagarDWC sub-system currently doesn't differentiate between prefetchable and non-prefetchable memory aperture entries in the 'ranges' property and provides ATU mapping only for the first memory aperture entry out of all the entries present. This was introduced by the
commit 0f71c60ffd26 ("PCI: dwc: Remove storing of PCI resources"). Mapping for a memory apreture is required if its CPU address and the bus address are different and the current mechanism works only if the memory aperture which needs mapping happens to be the first entry. It doesn't work either if the memory aperture that needs mapping is not the first entry or if both prefetchable and non-prefetchable apertures need mapping.
This patch fixes this issue by differentiating between prefetchable and non-prefetchable apertures in the 'ranges' property there by removing the dependency on the order in which they are specified and adds support for mapping prefetchable aperture using ATU region-3 if required.
---
Changes from previous versions:
* Addressed Rob's comments and as part of that split the patch into three sub-patches
* Rewrote commit subject and description
* Addressed review comments from Lorenzo
.../pci/controller/dwc/pcie-designware-host.c | 39 ++++++++++++++++--- drivers/pci/controller/dwc/pcie-designware.h | 1 + 2 files changed, 34 insertions(+), 6 deletions(-)
drivers/pci/controller/dwc/pcie-designware-host.c +33 -6
@@ -529,9 +529,39 @@ static struct pci_ops dw_pcie_ops = { .write = pci_generic_config_write, }; +static void dw_pcie_setup_mem_atu (struct pcie_port *pp, +struct resource_entry *win) +{ +struct dw_pcie *pci =to_dw_pcie_from_pp (pp); + +/* Check for prefetchable memory aperture */ +if (win->res->flags &IORESOURCE_PREFETCH ) { +/* Number of view ports must at least be 4 to enable mapping */ +if (pci->num_viewport <4 ) { +dev_warn (pci->dev, +"Insufficient ATU regions to map Prefetchable memory\n" ); + }else { +dw_pcie_prog_outbound_atu (pci, +PCIE_ATU_REGION_INDEX3 , +PCIE_ATU_TYPE_MEM , + win->res->start, + win->res->start - win->offset, +resource_size (win->res)); + } + }else {/* Non-prefetchable memory aperture */ +dw_pcie_prog_outbound_atu (pci, +PCIE_ATU_REGION_INDEX0 , +PCIE_ATU_TYPE_MEM , + win->res->start, + win->res->start - win->offset, +resource_size (win->res)); + } +} +void dw_pcie_setup_rc (struct pcie_port *pp) {u32 val, ctrl, num_ctrls; +struct resource_entry *win;struct dw_pcie *pci =to_dw_pcie_from_pp (pp);/*
@@ -586,13 +616,10 @@ void dw_pcie_setup_rc(struct pcie_port *pp)* ATU, so we should not program the ATU here. */ if (pp->bridge->child_ops == &dw_child_pcie_ops) { -struct resource_entry *entry = -resource_list_first_type (&pp->bridge->windows,IORESOURCE_MEM ); +resource_list_for_each_entry (win, &pp->bridge->windows) +if (resource_type (win->res) ==IORESOURCE_MEM ) +dw_pcie_setup_mem_atu (pp, win); -dw_pcie_prog_outbound_atu (pci,PCIE_ATU_REGION_INDEX0 , -PCIE_ATU_TYPE_MEM , entry->res->start, - entry->res->start - entry->offset, -resource_size (entry->res));if (pci->num_viewport >2 ) dw_pcie_prog_outbound_atu(pci, PCIE_ATU_REGION_INDEX2, PCIE_ATU_TYPE_IO, pp->io_base,
drivers/pci/controller/dwc/pcie-designware.h +1 -0
@@ -80,6 +80,7 @@#define PCIE_ATU_VIEWPORT 0x900#define PCIE_ATU_REGION_INBOUND BIT(31)#define PCIE_ATU_REGION_OUTBOUND 0 +#define PCIE_ATU_REGION_INDEX3 0x3#define PCIE_ATU_REGION_INDEX2 0x2#define PCIE_ATU_REGION_INDEX1 0x1#define PCIE_ATU_REGION_INDEX0 0x0
Signature · 1 line
2.17.1
Rob Herring
reviewerRe: [PATCH 3/3] PCI: dwc: Add support to handle prefetchable memory mapping
Quoted 12 lines · Vidya Sagar
DWC sub-system currently doesn't differentiate between prefetchable and non-prefetchable memory aperture entries in the 'ranges' property and provides ATU mapping only for the first memory aperture entry out of all the entries present. This was introduced by the
commit0f71c60ffd26("PCI: dwc: Remove storing of PCI resources"). Mapping for a memory apreture is required if its CPU address and the bus address are different and the current mechanism works only if the memory aperture which needs mapping happens to be the first entry. It doesn't work either if the memory aperture that needs mapping is not the first entry or if both prefetchable and non-prefetchable apertures need mapping.
Quoted 6 lines
This patch fixes this issue by differentiating between prefetchable and non-prefetchable apertures in the 'ranges' property there by removing the dependency on the order in which they are specified and adds support for mapping prefetchable aperture using ATU region-3 if required.
Fixes 0f71c60ffd26 ("PCI: dwc: Remove storing of PCI resources")
Fixes should come first, then new features.
Quoted 1 line
'Link' is the link for this message and should be a lore.kernel.org link. Maintainers will add it.
Quoted 39 lines
Signed-off-by Vidya Sagar <[email protected]>---
Changes from previous versions:
* Addressed Rob's comments and as part of that split the patch into three sub-patches
* Rewrote commit subject and description
* Addressed review comments from Lorenzo.../pci/controller/dwc/pcie-designware-host.c | 39 ++++++++++++++++--- drivers/pci/controller/dwc/pcie-designware.h | 1 + 2 files changed, 34 insertions(+), 6 deletions(-)drivers/pci/controller/dwc/pcie-designware-host.c +19
-0@@ -529,9 +529,39 @@ static struct pci_ops dw_pcie_ops = { .write = pci_generic_config_write, }; +static void dw_pcie_setup_mem_atu (struct pcie_port *pp, +struct resource_entry *win) +{ +struct dw_pcie *pci =to_dw_pcie_from_pp (pp); + +/* Check for prefetchable memory aperture */ +if (win->res->flags &IORESOURCE_PREFETCH ) { +/* Number of view ports must at least be 4 to enable mapping */ +if (pci->num_viewport <4 ) { +dev_warn (pci->dev, +"Insufficient ATU regions to map Prefetchable memory\n" ); + }else { +dw_pcie_prog_outbound_atu (pci, +PCIE_ATU_REGION_INDEX3 , +PCIE_ATU_TYPE_MEM , + win->res->start, + win->res->start - win->offset, +resource_size (win->res)); + }
drivers/pci/controller/dwc/pcie-designware-host.c static struct pci_ops dw_pcie_ops = { · line 560
Quoted 10 lines
drivers/pci/controller/dwc/pcie-designware-host.c +10
-0+ }else {/* Non-prefetchable memory aperture */ +dw_pcie_prog_outbound_atu (pci, +PCIE_ATU_REGION_INDEX0 , +PCIE_ATU_TYPE_MEM , + win->res->start, + win->res->start - win->offset, +resource_size (win->res)); + } +} +
This is in no way a minimal fix. I'll send my proposed fix.
Quoted 39 lines
drivers/pci/controller/dwc/pcie-designware-host.c +4
-6void dw_pcie_setup_rc (struct pcie_port *pp) {u32 val, ctrl, num_ctrls; +struct resource_entry *win;struct dw_pcie *pci =to_dw_pcie_from_pp (pp);/* @@ -586,13 +616,10 @@ void dw_pcie_setup_rc(struct pcie_port *pp)* ATU, so we should not program the ATU here. */ if (pp->bridge->child_ops == &dw_child_pcie_ops) { -struct resource_entry *entry = -resource_list_first_type (&pp->bridge->windows,IORESOURCE_MEM ); +resource_list_for_each_entry (win, &pp->bridge->windows) +if (resource_type (win->res) ==IORESOURCE_MEM ) +dw_pcie_setup_mem_atu (pp, win); -dw_pcie_prog_outbound_atu (pci,PCIE_ATU_REGION_INDEX0 , -PCIE_ATU_TYPE_MEM , entry->res->start, - entry->res->start - entry->offset, -resource_size (entry->res));if (pci->num_viewport >2 ) dw_pcie_prog_outbound_atu(pci, PCIE_ATU_REGION_INDEX2, PCIE_ATU_TYPE_IO, pp->io_base,drivers/pci/controller/dwc/pcie-designware.h +1
-1@@ -80,6 +80,7 @@#define PCIE_ATU_VIEWPORT 0x900#define PCIE_ATU_REGION_INBOUND BIT(31)#define PCIE_ATU_REGION_OUTBOUND 0 +#define PCIE_ATU_REGION_INDEX3 0x3#define PCIE_ATU_REGION_INDEX2 0x2#define PCIE_ATU_REGION_INDEX1 0x1#define PCIE_ATU_REGION_INDEX0 0x0 --2.17.1
Quoted 10 lines · Vidya Sagar
This patch series adds support for configuring the DesignWare IP's ATU region for prefetchable memory translations.
It first starts by flagging a warning if the size of non-prefetchable aperture goes beyond 32-bit as PCIe spec doesn't allow it. And then adds required support for programming the ATU to handle higher (i.e. >4GB) sizes and then finally adds support for differentiating between prefetchable and non-prefetchable regions and configuring one of the ATU regions for prefetchable memory translations purpose.
Quoted 4 lines
Vidya Sagar (3):
PCI: of: Warn if non-prefetchable memory aperture size is > 32-bit
PCI: dwc: Add support to program ATU for >4GB memory aperture sizes
PCI: dwc: Add support to handle prefetchable memory mapping
For 2nd & 3rd,
But, I still want someone to ack 1st patch, not me.
To Vidya,
If possible, can you ask your coworker to give 'Tested-by'? It will be very helpful. Thank you.
Best regards,
Jingoo Han
Quoted 9 lines
.../pci/controller/dwc/pcie-designware-host.c | 39 ++++++++++++++++--- drivers/pci/controller/dwc/pcie-designware.c | 12 +++--- drivers/pci/controller/dwc/pcie-designware.h | 4 +- drivers/pci/of.c | 5 +++ 4 files changed, 48 insertions(+), 12 deletions(-)Signature · 1 line
2.17.1
Thierry Reding
Tested-byQuoted 16 lines · Jingoo Han
Quoted 10 lines · Vidya Sagar
This patch series adds support for configuring the DesignWare IP's ATU region for prefetchable memory translations.
It first starts by flagging a warning if the size of non-prefetchable aperture goes beyond 32-bit as PCIe spec doesn't allow it. And then adds required support for programming the ATU to handle higher (i.e. >4GB) sizes and then finally adds support for differentiating between prefetchable and non-prefetchable regions and configuring one of the ATU regions for prefetchable memory translations purpose.Quoted 4 lines
Vidya Sagar (3):
PCI: of: Warn if non-prefetchable memory aperture size is > 32-bit
PCI: dwc: Add support to program ATU for >4GB memory aperture sizes
PCI: dwc: Add support to handle prefetchable memory mapping
Quoted 7 lines
For 2nd & 3rd,
Acked-by Jingoo <[email protected]>But, I still want someone to ack 1st patch, not me.
To Vidya,
If possible, can you ask your coworker to give 'Tested-by'? It will be very helpful. Thank you.
On next-20201026 (but also going back quite a while) I'm seeing this during boot on Jetson AGX Xavier (Tegra194):
[ 3.493382] ahci 0001:01:00.0: version 3.0 [ 3.493889] ahci 0001:01:00.0: SSS flag set, parallel bus scan disabled [ 4.497706] ahci 0001:01:00.0: controller reset failed (0xffffffff) [ 4.498114] ahci: probe of 0001:01:00.0 failed with error -5
After applying this series, AHCI over PCI is back to normal:
[ 3.543230] ahci 0001:01:00.0: AHCI 0001.0000 32 slots 1 ports 6 Gbps 0x1 impl SATA mode [ 3.550841] ahci 0001:01:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.559747] scsi host0: ahci [ 3.561998] ata1: SATA max UDMA/133 abar m512@0x1230010000 port 0x1230010100 irq 63
So for the series:
Lorenzo / Bjorn,
Could you please review patches-1 & 2 in this series?
For the third patch, we already went with Rob's patch @ http://patchwork.ozlabs.org/project/linux-pci/patch/[email protected]/
Thanks,
Vidya Sagar
Quoted 44 lines · Thierry Reding
Quoted 16 lines · Jingoo Han
Quoted 10 lines · Vidya Sagar
This patch series adds support for configuring the DesignWare IP's ATU region for prefetchable memory translations.
It first starts by flagging a warning if the size of non-prefetchable aperture goes beyond 32-bit as PCIe spec doesn't allow it. And then adds required support for programming the ATU to handle higher (i.e. >4GB) sizes and then finally adds support for differentiating between prefetchable and non-prefetchable regions and configuring one of the ATU regions for prefetchable memory translations purpose.Quoted 4 lines
Vidya Sagar (3):
PCI: of: Warn if non-prefetchable memory aperture size is > 32-bit
PCI: dwc: Add support to program ATU for >4GB memory aperture sizes
PCI: dwc: Add support to handle prefetchable memory mappingQuoted 7 lines
For 2nd & 3rd,
Acked-by Jingoo <[email protected]>But, I still want someone to ack 1st patch, not me.
To Vidya,
If possible, can you ask your coworker to give 'Tested-by'? It will be very helpful. Thank you.On next-20201026 (but also going back quite a while) I'm seeing this during boot on Jetson AGX Xavier (Tegra194):
[ 3.493382] ahci 0001:01:00.0: version 3.0 [ 3.493889] ahci 0001:01:00.0: SSS flag set, parallel bus scan disabled [ 4.497706] ahci 0001:01:00.0: controller reset failed (0xffffffff) [ 4.498114] ahci: probe of 0001:01:00.0 failed with error -5After applying this series, AHCI over PCI is back to normal:
[ 3.543230] ahci 0001:01:00.0: AHCI 0001.0000 32 slots 1 ports 6 Gbps 0x1 impl SATA mode [ 3.550841] ahci 0001:01:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.559747] scsi host0: ahci [ 3.561998] ata1: SATA max UDMA/133 abar m512@0x1230010000 port 0x1230010100 irq 63So for the series:
Tested-by Thierry Reding <[email protected]>
Hi Lorenzo & Bjorn,
Sorry to bother you.
Could you please take a look at the patches-1 & 2 from this series?
Thanks,
Vidya Sagar
Quoted 57 lines · Vidya Sagar
External email: Use caution opening links or attachments
Lorenzo / Bjorn,
Could you please review patches-1 & 2 in this series? For the third patch, we already went with Rob's patch @
http://patchwork.ozlabs.org/project/linux-pci/patch/[email protected]/Thanks,
Vidya SagarQuoted 44 lines · Thierry Reding
Quoted 16 lines · Jingoo Han
Quoted 10 lines · Vidya Sagar
This patch series adds support for configuring the DesignWare IP's ATU region for prefetchable memory translations.
It first starts by flagging a warning if the size of non-prefetchable aperture goes beyond 32-bit as PCIe spec doesn't allow it. And then adds required support for programming the ATU to handle higher (i.e. >4GB) sizes and then finally adds support for differentiating between prefetchable and non-prefetchable regions and configuring one of the ATU regions for prefetchable memory translations purpose.Quoted 4 lines
Vidya Sagar (3):
PCI: of: Warn if non-prefetchable memory aperture size is > 32-bit
PCI: dwc: Add support to program ATU for >4GB memory aperture sizes
PCI: dwc: Add support to handle prefetchable memory mappingQuoted 7 lines
For 2nd & 3rd,
Acked-by Jingoo <[email protected]>But, I still want someone to ack 1st patch, not me.
To Vidya,
If possible, can you ask your coworker to give 'Tested-by'? It will be very helpful. Thank you.On next-20201026 (but also going back quite a while) I'm seeing this during boot on Jetson AGX Xavier (Tegra194):
[ 3.493382] ahci 0001:01:00.0: version 3.0
[ 3.493889] ahci 0001:01:00.0: SSS flag set, parallel bus scan disabled [ 4.497706] ahci 0001:01:00.0: controller reset failed (0xffffffff) [ 4.498114] ahci: probe of 0001:01:00.0 failed with error -5After applying this series, AHCI over PCI is back to normal:
[ 3.543230] ahci 0001:01:00.0: AHCI 0001.0000 32 slots 1 ports 6 Gbps
0x1impl SATA mode [ 3.550841] ahci 0001:01:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.559747] scsi host0: ahci
[ 3.561998] ata1: SATA max UDMA/133 abar m512@0x1230010000 port0x1230010100irq 63So for the series:
Tested-by Thierry Reding <[email protected]>
Re: [PATCH 0/3] Add support to handle prefetchable memoryg
Quoted 3 lines · Vidya Sagar
Hi Lorenzo & Bjorn,
Sorry to bother you.
Could you please take a look at the patches-1 & 2 from this series?
IIUC we should:
(1) apply https://patchwork.kernel.org/project/linux-pci/patch/[email protected]
(2) apply [1,2] from this series
For (2), are they rebased against v5.10-rc3 with (1) applied ? I need to check but I will probably have to use v5.10-rc3 as baseline owing to commit:
9fff3256f93d
(1) depends on it.
Lorenzo
Quoted 67 lines
Thanks,
Vidya SagarQuoted 63 lines · Vidya Sagar
External email: Use caution opening links or attachments
Lorenzo / Bjorn,
Could you please review patches-1 & 2 in this series? For the third patch, we already went with Rob's patch @
http://patchwork.ozlabs.org/project/linux-pci/patch/[email protected]/Thanks,
Vidya SagarQuoted 50 lines · Thierry Reding
Quoted 17 lines · Jingoo Han
Quoted 11 lines · Vidya Sagar
This patch series adds support for configuring the DesignWare IP's ATU region for prefetchable memory translations.
It first starts by flagging a warning if the size of non-prefetchable aperture goes beyond 32-bit as PCIe spec doesn't allow it. And then adds required support for programming the ATU to handle higher (i.e. >4GB) sizes and then finally adds support for differentiating between prefetchable and non-prefetchable regions and configuring one of
the ATU regions for prefetchable memory translations purpose.Quoted 4 lines
Vidya Sagar (3):
PCI: of: Warn if non-prefetchable memory aperture size is > 32-bit
PCI: dwc: Add support to program ATU for >4GB memory aperture sizes
PCI: dwc: Add support to handle prefetchable memory mappingQuoted 8 lines
For 2nd & 3rd,
Acked-by Jingoo <[email protected]>But, I still want someone to ack 1st patch, not me.
To Vidya,
If possible, can you ask your coworker to give 'Tested-by'? It will be very helpful.
Thank you.On next-20201026 (but also going back quite a while) I'm seeing this during boot on Jetson AGX Xavier (Tegra194):
[ 3.493382] ahci 0001:01:00.0: version 3.0
[ 3.493889] ahci 0001:01:00.0: SSS flag set, parallel bus scan disabled
[ 4.497706] ahci 0001:01:00.0: controller reset failed (0xffffffff) [ 4.498114] ahci: probe of 0001:01:00.0 failed with error -5After applying this series, AHCI over PCI is back to normal:
[ 3.543230] ahci 0001:01:00.0: AHCI 0001.0000 32 slots 1 ports 6 Gbps
0x1impl SATA mode
[ 3.550841] ahci 0001:01:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 3.559747] scsi host0: ahci
[ 3.561998] ata1: SATA max UDMA/133 abar m512@0x1230010000 port0x1230010100irq 63So for the series:
Tested-by Thierry Reding <[email protected]>
Re: [PATCH 0/3] Add support to handle prefetchable memoryg
Quoted 17 lines · Lorenzo Pieralisi
External email: Use caution opening links or attachments
Quoted 3 lines · Vidya Sagar
Hi Lorenzo & Bjorn,
Sorry to bother you.
Could you please take a look at the patches-1 & 2 from this series?IIUC we should:
(1) apply https://patchwork.kernel.org/project/linux-pci/patch/[email protected]
(2) apply [1,2] from this seriesFor (2), are they rebased against v5.10-rc3 with (1) applied ? I need to check but I will probably have to use v5.10-rc3 as baseline owing to commit:
Quoted 5 lines
9fff3256f93d(1) depends on it.
Lorenzo
My patches [1,2] from this series apply cleanly on v5.10-rc3. But with (1) applied first, there is a trivial rebase required. Let me know if you want me to send the trivial rebased version (of patch-2 particularly).
Thanks,
Vidya Sagar
Quoted 68 lines
Quoted 68 lines
Thanks,
Vidya SagarQuoted 63 lines · Vidya Sagar
External email: Use caution opening links or attachments
Lorenzo / Bjorn,
Could you please review patches-1 & 2 in this series? For the third patch, we already went with Rob's patch @
http://patchwork.ozlabs.org/project/linux-pci/patch/[email protected]/Thanks,
Vidya SagarQuoted 50 lines · Thierry Reding
Quoted 17 lines · Jingoo Han
Quoted 11 lines · Vidya Sagar
This patch series adds support for configuring the DesignWare IP's ATU region for prefetchable memory translations.
It first starts by flagging a warning if the size of non-prefetchable aperture goes beyond 32-bit as PCIe spec doesn't allow it. And then adds required support for programming the ATU to handle higher (i.e. >4GB) sizes and then finally adds support for differentiating between prefetchable and non-prefetchable regions and configuring one of
the ATU regions for prefetchable memory translations purpose.Quoted 4 lines
Vidya Sagar (3):
PCI: of: Warn if non-prefetchable memory aperture size is > 32-bit
PCI: dwc: Add support to program ATU for >4GB memory aperture sizes
PCI: dwc: Add support to handle prefetchable memory mappingQuoted 8 lines
For 2nd & 3rd,
Acked-by Jingoo <[email protected]>But, I still want someone to ack 1st patch, not me.
To Vidya,
If possible, can you ask your coworker to give 'Tested-by'? It will be very helpful.
Thank you.On next-20201026 (but also going back quite a while) I'm seeing this during boot on Jetson AGX Xavier (Tegra194):
[ 3.493382] ahci 0001:01:00.0: version 3.0
[ 3.493889] ahci 0001:01:00.0: SSS flag set, parallel bus scan disabled
[ 4.497706] ahci 0001:01:00.0: controller reset failed (0xffffffff) [ 4.498114] ahci: probe of 0001:01:00.0 failed with error -5After applying this series, AHCI over PCI is back to normal:
[ 3.543230] ahci 0001:01:00.0: AHCI 0001.0000 32 slots 1 ports 6 Gbps
0x1impl SATA mode
[ 3.550841] ahci 0001:01:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 3.559747] scsi host0: ahci
[ 3.561998] ata1: SATA max UDMA/133 abar m512@0x1230010000 port0x1230010100irq 63So for the series:
Tested-by Thierry Reding <[email protected]>
On Tue, Nov 17, 2020 at 11:04:57PM +0530, Vidya Sagar wrote:
[...]
Quoted 9 lines
Quoted 9 lines
IIUC we should:
(1) apply https://patchwork.kernel.org/project/linux-pci/patch/[email protected]
(2) apply [1,2] from this seriesFor (2), are they rebased against v5.10-rc3 with (1) applied ? I need to check but I will probably have to use v5.10-rc3 as baseline owing to commit:
Quoted 8 lines
Quoted 5 lines
9fff3256f93d(1) depends on it.
Lorenzo
My patches [1,2] from this series apply cleanly on v5.10-rc3. But with (1) applied first, there is a trivial rebase required. Let me know if you want me to send the trivial rebased version (of patch-2 particularly).
Please do - I shall apply (1) first (on top of v5.10-rc3).
Lorenzo
Jon Hunter
Tested-byQuoted 35 lines · Thierry Reding
Quoted 16 lines · Jingoo Han
Quoted 10 lines · Vidya Sagar
This patch series adds support for configuring the DesignWare IP's ATU region for prefetchable memory translations.
It first starts by flagging a warning if the size of non-prefetchable aperture goes beyond 32-bit as PCIe spec doesn't allow it. And then adds required support for programming the ATU to handle higher (i.e. >4GB) sizes and then finally adds support for differentiating between prefetchable and non-prefetchable regions and configuring one of the ATU regions for prefetchable memory translations purpose.Quoted 4 lines
Vidya Sagar (3):
PCI: of: Warn if non-prefetchable memory aperture size is > 32-bit
PCI: dwc: Add support to program ATU for >4GB memory aperture sizes
PCI: dwc: Add support to handle prefetchable memory mappingQuoted 7 lines
For 2nd & 3rd,
Acked-by Jingoo <[email protected]>But, I still want someone to ack 1st patch, not me.
To Vidya,
If possible, can you ask your coworker to give 'Tested-by'? It will be very helpful. Thank you.On next-20201026 (but also going back quite a while) I'm seeing this during boot on Jetson AGX Xavier (Tegra194):
[ 3.493382] ahci 0001:01:00.0: version 3.0 [ 3.493889] ahci 0001:01:00.0: SSS flag set, parallel bus scan disabled [ 4.497706] ahci 0001:01:00.0: controller reset failed (0xffffffff) [ 4.498114] ahci: probe of 0001:01:00.0 failed with error -5After applying this series, AHCI over PCI is back to normal:
Quoted 8 lines
[ 3.543230] ahci 0001:01:00.0: AHCI 0001.0000 32 slots 1 ports 6 Gbps 0x1 impl SATA mode [ 3.550841] ahci 0001:01:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.559747] scsi host0: ahci [ 3.561998] ata1: SATA max UDMA/133 abar m512@0x1230010000 port 0x1230010100 irq 63So for the series:
Tested-by Thierry Reding <[email protected]>
FWIW ...
Cheers
Jon
Signature · 1 line
nvpublic